<?xml version="1.0" encoding="utf-8"?>
<XDFFORMAT version="1.60">
  <XDFHEADER>
    <flags>0x1</flags>
    <deftitle>P12 Suite - P12 OS 12627882 (catalog draft) - CATALOG DRAFT</deftitle>
    <description>OS ID 12627882 ONLY. P12 Suite catalog draft: every item was located and checked in this OS&#x27;s code (the routine that reads it is the same code as in the P12 Suite H3 definition, OS 12627884, and its table header, lookup and values were checked); not confirmed on a vehicle. Descriptions and quoted stock values describe the H3. Big-endian. Table axes are computed by the code, so axis labels are fixed values, not bin data. NO CHECKSUM is defined on purpose: after saving, correct the P12 segment checksums (python h3suite/run.py p12 repair &lt;bin&gt;, or a flashing tool that corrects P12 segments) before any flash. Edit in small steps and log.</description>
    <BASEOFFSET offset="0" subtract="0" />
    <DEFAULTS datasizeinbits="16" sigdigits="2" outputtype="1" signed="0" lsbfirst="0" float="0" />
    <REGION type="0xFFFFFFFF" startaddress="0x0" size="0x100000" regionflags="0x0" name="Bin" desc="P12 image" />
    <CATEGORY index="0x0" name="Fuel" />
    <CATEGORY index="0x1" name="Spark" />
    <CATEGORY index="0x2" name="Airflow" />
    <CATEGORY index="0x3" name="Idle" />
    <CATEGORY index="0x4" name="Transmission" />
    <CATEGORY index="0x5" name="Diagnostics" />
    <CATEGORY index="0x6" name="Engine" />
    <CATEGORY index="0x7" name="Torque" />
    <CATEGORY index="0x8" name="Limits" />
    <CATEGORY index="0x9" name="Speedometer" />
    <CATEGORY index="0xA" name="Throttle" />
    <CATEGORY index="0xB" name="Sensors" />
    <CATEGORY index="0xC" name="Segment Info" />
  </XDFHEADER>
  <XDFTABLE uniqueid="0x0" flags="0x30">
    <title>Transient Fuel - Wall Evaporation Fraction vs MAP vs Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of the port wall fuel film that evaporates into the cylinder each update (the wall-wetting time constant), by MAP (rows) and port temperature (columns). Stock 0.10 cold to 0.22 hot at 20 kPa. Effect: raise = wall film dries faster (shorter tip-in/tip-out fuel corrections) Evidence: ledger:E0002, ledger:E0057, ledger:E0213, ledger:E0218, ledger:E0316</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (modelled temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-24" />
      <LABEL index="2" value="-8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="24" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="56" />
      <LABEL index="7" value="72" />
      <LABEL index="8" value="88" />
      <LABEL index="9" value="104" />
      <LABEL index="10" value="120" />
      <LABEL index="11" value="136" />
      <LABEL index="12" value="152" />
      <LABEL index="13" value="168" />
      <LABEL index="14" value="184" />
      <LABEL index="15" value="200" />
      <LABEL index="16" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="20" />
      <LABEL index="1" value="30" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="50" />
      <LABEL index="4" value="60" />
      <LABEL index="5" value="70" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="90" />
      <LABEL index="8" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26904" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1" flags="0x30">
    <title>Main Spark Advance - High Octane</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base spark advance vs cylinder airmass x RPM, high-octane table. The PCM runs High minus (High - Low) x the learned octane scaler: scaler 0 = pure High, 1.0 = pure Low. After a reset or fault the scaler starts at 1.0 (all Low) and octane learn moves it toward High while there is no knock (E0296). Effect: increase = more timing &amp; torque (and more knock risk) Evidence: ledger:E0002, ledger:E0003, ledger:E0004, ledger:E0006, ledger:E0069, ledger:E0071, ledger:E0175, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E0296, ledger:E1297, ledger:E1338</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2D191" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x2" flags="0x30">
    <title>Main Spark Advance - Low Octane</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base spark advance vs cylinder airmass x RPM, low-octane table. Retarded 0-10.5 deg relative to high octane at mid/high load. The PCM runs High minus (High - Low) x the learned octane scaler: scaler 0 = pure High, 1.0 = pure Low. After a reset or fault the scaler starts at 1.0 (all Low) and octane learn moves it toward High while there is no knock (E0296). Effect: increase = more timing &amp; torque (and more knock risk) Evidence: ledger:E0002, ledger:E0003, ledger:E0005, ledger:E0006, ledger:E0069, ledger:E0071, ledger:E0175, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E0296, ledger:E1297</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2D6C9" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3" flags="0x30">
    <title>Power Enrichment EQ vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded fuel mixture during power enrichment, by engine speed (EQ: 1.0 = stoichiometric, higher = richer, lambda = 1 / EQ). This is the only power enrichment mixture table and it has no load or manifold pressure input: under boost every boost level gets the same mixture at a given rpm. The PCM commands the richest of power enrichment, catalyst over-temperature protection and coolant over-temperature enrichment. Stock about 1.20 at 4000 rpm. Effect: raise = richer full-load mixture at that rpm (at every boost level) Evidence: ledger:E0030, ledger:E0041, ledger:E0126, ledger:E0175, ledger:E0257, ledger:E0260, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28E2E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4" flags="0x30">
    <title>PE enable throttle vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle opening, by engine speed, at or above which power enrichment is allowed (a barometric adder curve, all zero on the stock calibration, is added to it). Power enrichment also needs manifold pressure at or above the minimum MAP and rpm at or above the minimum rpm. Effect: lower = power enrichment starts at a smaller throttle opening Evidence: ledger:E0032, ledger:E0106, ledger:E0162, ledger:E0197, ledger:E0236, ledger:E0257, ledger:E0260, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28BCC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5" flags="0x0">
    <title>PE enable hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once power enrichment is active, the throttle threshold drops by this much, so it stays on until the throttle closes this far below the enable value. Effect: raise = power enrichment holds on longer as the throttle closes Evidence: ledger:E0032, ledger:E0147, ledger:E0151, ledger:E0194, ledger:E0197, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28BA0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6" flags="0x0">
    <title>PE ramp-in rate (Q15 per pass)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How quickly the commanded mixture moves toward the power enrichment target each update when richening. Effect: raise = power enrichment richens faster Evidence: ledger:E0031, ledger:E0145, ledger:E0151, ledger:E0194, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28BB0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction of full PE per pass</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7" flags="0x0">
    <title>PE ramp-out rate (Q15 per pass)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How quickly the commanded mixture falls back each update when leaving power enrichment or when the target leans out. Effect: raise = the mixture leans out faster after power enrichment Evidence: ledger:E0031, ledger:E0145, ledger:E0151, ledger:E0194, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28BB2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction of full PE per pass</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8" flags="0x0">
    <title>Stoichiometric AFR</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0024, ledger:E0143, ledger:E0151</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26DEE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>AFR</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9" flags="0x0">
    <title>Minimum commanded EQ under lean offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0033, ledger:E0151, ledger:E0195, ledger:E0212</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26DF0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ (fuel/air, 1.0 = stoich; lambda = 1/EQ)</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA" flags="0x0">
    <title>Maximum commanded EQ (state 2)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0033, ledger:E0151, ledger:E0195, ledger:E0212</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26DF2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ (fuel/air, 1.0 = stoich; lambda = 1/EQ)</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB" flags="0x30">
    <title>Misfire Catalyst-Protection EQ</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded EQ used ONLY while the misfire monitor sees &gt; 100 misfires in its test window: lean below ~2560 rpm, rich above, vs MAP x rpm. Normal closed loop commands 1.000 and open loop uses the OL EQ tables. Emissions/catalyst protection - do not tune Effect: fuelling during heavy misfire only (catalyst protection) Evidence: ledger:E0025, ledger:E0098, ledger:E0166, ledger:E0212, ledger:E0213, ledger:E0220, ledger:E0222, ledger:E0785, ledger:E1329</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="20" />
      <LABEL index="1" value="30" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="50" />
      <LABEL index="4" value="60" />
      <LABEL index="5" value="70" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="90" />
      <LABEL index="8" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26F60" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ (fuel/air, 1.0 = stoich; lambda = 1/EQ)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC" flags="0x30">
    <title>Open-loop EQ, in gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0041, ledger:E0043, ledger:E0120, ledger:E0121, ledger:E0164, ledger:E0175, ledger:E0196, ledger:E0211, ledger:E0213, ledger:E0222, ledger:E0257, ledger:E0260, ledger:E0288, ledger:E0785, ledger:E1329</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant at start)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>degC (modelled temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28278" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD" flags="0x30">
    <title>Open-loop EQ, park/neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0041, ledger:E0043, ledger:E0120, ledger:E0121, ledger:E0164, ledger:E0175, ledger:E0196, ledger:E0211, ledger:E0213, ledger:E0222, ledger:E0272, ledger:E0288, ledger:E0785, ledger:E1329</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant at start)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>degC (modelled temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x286E0" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE" flags="0x30">
    <title>MAF transfer curve (airflow vs output frequency)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Effect: increase = PCM believes more air is entering (richer fuelling) Evidence: ledger:E0042, ledger:E0110, ledger:E0111, ledger:E0112, ledger:E0113, ledger:E0114, ledger:E0175, ledger:E0219, ledger:E0230, ledger:E0685</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>Hz (MAF output frequency)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1500" />
      <LABEL index="1" value="1800" />
      <LABEL index="2" value="2100" />
      <LABEL index="3" value="2400" />
      <LABEL index="4" value="2700" />
      <LABEL index="5" value="3000" />
      <LABEL index="6" value="3300" />
      <LABEL index="7" value="3600" />
      <LABEL index="8" value="3900" />
      <LABEL index="9" value="4200" />
      <LABEL index="10" value="4500" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5100" />
      <LABEL index="13" value="5400" />
      <LABEL index="14" value="5700" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6300" />
      <LABEL index="17" value="6600" />
      <LABEL index="18" value="6900" />
      <LABEL index="19" value="7200" />
      <LABEL index="20" value="7500" />
      <LABEL index="21" value="7800" />
      <LABEL index="22" value="8100" />
      <LABEL index="23" value="8400" />
      <LABEL index="24" value="8700" />
      <LABEL index="25" value="9000" />
      <LABEL index="26" value="9300" />
      <LABEL index="27" value="9600" />
      <LABEL index="28" value="9900" />
      <LABEL index="29" value="10200" />
      <LABEL index="30" value="10500" />
      <LABEL index="31" value="10800" />
      <LABEL index="32" value="11100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C56A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xF" flags="0x30">
    <title>Injector flow rate vs kPa vacuum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0046, ledger:E0101, ledger:E0117, ledger:E0118, ledger:E0166, ledger:E0196, ledger:E0197, ledger:E0236, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (manifold vacuum)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2664C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x10" flags="0x30">
    <title>Desired idle vs coolant temp - IN GEAR</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target idle speed vs engine coolant temperature with the transmission in gear. Lower than the park/neutral target at the same temperature, which is the expected direction for a GM automatic. Warm-up log matches the part of the curve shared with the other idle curve (186 samples at 47-88 C, mean error 4.7 rpm, E0115). Which curve is Park/Neutral and which is in-gear rests on code (E0123). Evidence: ledger:E0048, ledger:E0115, ledger:E0123, ledger:E0158, ledger:E0231</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A082" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x11" flags="0x0">
    <title>Desired idle ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0049, ledger:E0151, ledger:E0195</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A56E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x12" flags="0x0">
    <title>Octane scaler default (reset/fault)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Octane scaler value after a reset or fault. Stock 1.0 = run the Low Octane spark table until octane learn moves toward High (E0296). Lower it to start closer to High octane. Evidence: ledger:E0007, ledger:E0151, ledger:E0193, ledger:E0296</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AE96" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0..1</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x13" flags="0x0">
    <title>Knock retard threshold for octane learn</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum per-cylinder knock retard for an octane-learn step. Stock 2.0 deg. Evidence: ledger:E0008, ledger:E0151, ledger:E0193, ledger:E0218</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AE94" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x14" flags="0x0">
    <title>Octane scaler decay gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0009, ledger:E0151, ledger:E0193</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AE52" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x15" flags="0x0">
    <title>Max cylinder octane-scaler spread</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0010, ledger:E0151, ledger:E0193</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2ACD2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0..1</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x16" flags="0x30">
    <title>Force motor (PCS) current vs commanded line pressure - used while pressure FALLING</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0050, ledger:E0059, ledger:E0124, ledger:E0125, ledger:E0135, ledger:E0168, ledger:E0174, ledger:E1352</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (commanded line pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="40" />
      <LABEL index="2" value="80" />
      <LABEL index="3" value="120" />
      <LABEL index="4" value="160" />
      <LABEL index="5" value="200" />
      <LABEL index="6" value="240" />
      <LABEL index="7" value="280" />
      <LABEL index="8" value="320" />
      <LABEL index="9" value="360" />
      <LABEL index="10" value="400" />
      <LABEL index="11" value="440" />
      <LABEL index="12" value="480" />
      <LABEL index="13" value="520" />
      <LABEL index="14" value="560" />
      <LABEL index="15" value="600" />
      <LABEL index="16" value="640" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC (trans fluid)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E0C7" mmedelementsizebits="8" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>A</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x17" flags="0x30">
    <title>Catalyst Monitor - Storage Time Normaliser</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier applied to the measured catalyst oxygen storage time before it is compared with the storage time reference, by mean airflow during the lean fuel step (columns, 0 to 16 g/s) and modelled catalyst temperature (rows, 300 to 800 C). Higher values make the catalyst look better, so the efficiency code is less likely. Stock at 6 g/s: 3.84 at 300 C falling to 0.58 at 800 C; flat below 3 g/s. Effect: raise = the measured storage time counts for more, so a weak catalyst is less likely to set the efficiency code Evidence: ledger:E0002, ledger:E0056, ledger:E0133, ledger:E1021, ledger:E1189, ledger:E1191, ledger:E1297</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s (mean airflow over the test step)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.5" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="1.5" />
      <LABEL index="4" value="2" />
      <LABEL index="5" value="2.5" />
      <LABEL index="6" value="3" />
      <LABEL index="7" value="3.5" />
      <LABEL index="8" value="4" />
      <LABEL index="9" value="4.5" />
      <LABEL index="10" value="5" />
      <LABEL index="11" value="5.5" />
      <LABEL index="12" value="6" />
      <LABEL index="13" value="6.5" />
      <LABEL index="14" value="7" />
      <LABEL index="15" value="7.5" />
      <LABEL index="16" value="8" />
      <LABEL index="17" value="8.5" />
      <LABEL index="18" value="9" />
      <LABEL index="19" value="9.5" />
      <LABEL index="20" value="10" />
      <LABEL index="21" value="10.5" />
      <LABEL index="22" value="11" />
      <LABEL index="23" value="11.5" />
      <LABEL index="24" value="12" />
      <LABEL index="25" value="12.5" />
      <LABEL index="26" value="13" />
      <LABEL index="27" value="13.5" />
      <LABEL index="28" value="14" />
      <LABEL index="29" value="14.5" />
      <LABEL index="30" value="15" />
      <LABEL index="31" value="15.5" />
      <LABEL index="32" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>degC (catalyst temperature model)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="300" />
      <LABEL index="1" value="362.5" />
      <LABEL index="2" value="425" />
      <LABEL index="3" value="487.5" />
      <LABEL index="4" value="550" />
      <LABEL index="5" value="612.5" />
      <LABEL index="6" value="675" />
      <LABEL index="7" value="737.5" />
      <LABEL index="8" value="800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x329F3" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x18" flags="0x30">
    <title>ECT Spark Advance Correction - additive</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark advance added by coolant temperature (columns) and cylinder airmass (rows), 0.5 deg per count. Identified from a related GM operating system by code homology and confirmed on the H3 by its index source. Effect: increase = more timing added at that temperature and airmass Evidence: ledger:E0002, ledger:E0071, ledger:E0072, ledger:E0073, ledger:E0137, ledger:E0138, ledger:E0139, ledger:E0140, ledger:E0175, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl (cylinder airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2DCD9" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x19" flags="0x30">
    <title>IAT Spark Advance Correction - additive</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark advance added by intake air temperature (columns) and cylinder airmass (rows), 0.5 deg per count. Identified from a related GM operating system by code homology and confirmed on the H3 by its index source. Effect: increase = more timing added at that temperature and airmass Evidence: ledger:E0002, ledger:E0071, ledger:E0072, ledger:E0074, ledger:E0140, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl (cylinder airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E039" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1A" flags="0x30">
    <title>ECT Spark Advance Correction - multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier applied alongside the ECT additive spark correction, by coolant temperature and airmass. Stock 0.602 to 0.996. Evidence: ledger:E0002, ledger:E0075, ledger:E0141, ledger:E0160, ledger:E0257, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-20" />
      <LABEL index="1" value="-10" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="10" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="30" />
      <LABEL index="6" value="40" />
      <LABEL index="7" value="50" />
      <LABEL index="8" value="60" />
      <LABEL index="9" value="70" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="90" />
      <LABEL index="12" value="100" />
      <LABEL index="13" value="110" />
      <LABEL index="14" value="120" />
      <LABEL index="15" value="130" />
      <LABEL index="16" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2DF11" mmedelementsizebits="8" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor (applied to the ECT add correction)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>0.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1B" flags="0x30">
    <title>IAT Spark Advance Correction - multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier applied alongside the IAT additive spark correction, by intake air temperature and airmass. Stock 0.602 to 0.996. Evidence: ledger:E0002, ledger:E0076, ledger:E0141, ledger:E0160, ledger:E0257, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC (intake air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E271" mmedelementsizebits="8" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor (applied to the IAT add correction)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>0.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1C" flags="0x30">
    <title>VE / Airflow model at cam phase 0 deg (bank 1 of 5)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam-phase VE bank for 0 deg cam. LIVE on the stock H3 at idle and light load (cam at 0 deg); under load above about 2000 rpm the load-based cam target (9 to 11 desired-cam degrees) would move the model toward banks 4 and 5. Edit THIS bank for VE changes - but steady-state fuelling follows the MAF and a uniform VE change is absorbed by the learned MAF/VE ratio (0.5 to 1.5), so VE shape matters in transients and is the only airflow source in MAF-fault mode 1. Cam axis note: the PCM halves its actual cam reading before comparing it with desired cam, so this axis counts twice as many units per degree as the desired-cam items...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="15" />
      <LABEL index="1" value="20.625" />
      <LABEL index="2" value="26.25" />
      <LABEL index="3" value="31.875" />
      <LABEL index="4" value="37.5" />
      <LABEL index="5" value="43.125" />
      <LABEL index="6" value="48.75" />
      <LABEL index="7" value="54.375" />
      <LABEL index="8" value="60" />
      <LABEL index="9" value="65.625" />
      <LABEL index="10" value="71.25" />
      <LABEL index="11" value="76.875" />
      <LABEL index="12" value="82.5" />
      <LABEL index="13" value="88.125" />
      <LABEL index="14" value="93.75" />
      <LABEL index="15" value="99.375" />
      <LABEL index="16" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B256" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mg K/kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1D" flags="0x30">
    <title>VE / Airflow model at cam phase 9 deg (bank 2 of 5)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam-phase VE bank for 9 deg cam. Dormant at idle and light load on the stock H3; probably used under load above about 2000 rpm, where a load-based path commands 9 to 11 desired-cam degrees (between banks 4 and 5 on this axis) (E0358, not yet confirmed on the road). Used when the cam is phased toward 9 deg, Check a loaded log before assuming edits here do nothing. Cam axis note: the PCM halves its actual cam reading before comparing it with desired cam, so this axis counts twice as many units per degree as the desired-cam items in this file (the load-based target of 9 to 11 desired-cam degrees sits at about 18 to 22 here)...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="15" />
      <LABEL index="1" value="20.625" />
      <LABEL index="2" value="26.25" />
      <LABEL index="3" value="31.875" />
      <LABEL index="4" value="37.5" />
      <LABEL index="5" value="43.125" />
      <LABEL index="6" value="48.75" />
      <LABEL index="7" value="54.375" />
      <LABEL index="8" value="60" />
      <LABEL index="9" value="65.625" />
      <LABEL index="10" value="71.25" />
      <LABEL index="11" value="76.875" />
      <LABEL index="12" value="82.5" />
      <LABEL index="13" value="88.125" />
      <LABEL index="14" value="93.75" />
      <LABEL index="15" value="99.375" />
      <LABEL index="16" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B49E" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mg K/kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1E" flags="0x30">
    <title>VE / Airflow model at cam phase 12 deg (bank 3 of 5)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam-phase VE bank for 12 deg cam. Dormant at idle and light load on the stock H3; probably used under load above about 2000 rpm, where a load-based path commands 9 to 11 desired-cam degrees (between banks 4 and 5 on this axis) (E0358, not yet confirmed on the road). Used when the cam is phased toward 12 deg, Check a loaded log before assuming edits here do nothing. Cam axis note: the PCM halves its actual cam reading before comparing it with desired cam, so this axis counts twice as many units per degree as the desired-cam items in this file (the load-based target of 9 to 11 desired-cam degrees sits at about 18 to 22 her...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="15" />
      <LABEL index="1" value="20.625" />
      <LABEL index="2" value="26.25" />
      <LABEL index="3" value="31.875" />
      <LABEL index="4" value="37.5" />
      <LABEL index="5" value="43.125" />
      <LABEL index="6" value="48.75" />
      <LABEL index="7" value="54.375" />
      <LABEL index="8" value="60" />
      <LABEL index="9" value="65.625" />
      <LABEL index="10" value="71.25" />
      <LABEL index="11" value="76.875" />
      <LABEL index="12" value="82.5" />
      <LABEL index="13" value="88.125" />
      <LABEL index="14" value="93.75" />
      <LABEL index="15" value="99.375" />
      <LABEL index="16" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B6E6" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mg K/kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1F" flags="0x30">
    <title>VE / Airflow model at cam phase 16 deg (bank 4 of 5)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam-phase VE bank for 16 deg cam. Dormant at idle and light load on the stock H3; probably used under load above about 2000 rpm, where a load-based path commands 9 to 11 desired-cam degrees (between banks 4 and 5 on this axis) (E0358, not yet confirmed on the road). Used when the cam is phased toward 16 deg, Check a loaded log before assuming edits here do nothing. Cam axis note: the PCM halves its actual cam reading before comparing it with desired cam, so this axis counts twice as many units per degree as the desired-cam items in this file (the load-based target of 9 to 11 desired-cam degrees sits at about 18 to 22 her...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="15" />
      <LABEL index="1" value="20.625" />
      <LABEL index="2" value="26.25" />
      <LABEL index="3" value="31.875" />
      <LABEL index="4" value="37.5" />
      <LABEL index="5" value="43.125" />
      <LABEL index="6" value="48.75" />
      <LABEL index="7" value="54.375" />
      <LABEL index="8" value="60" />
      <LABEL index="9" value="65.625" />
      <LABEL index="10" value="71.25" />
      <LABEL index="11" value="76.875" />
      <LABEL index="12" value="82.5" />
      <LABEL index="13" value="88.125" />
      <LABEL index="14" value="93.75" />
      <LABEL index="15" value="99.375" />
      <LABEL index="16" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B92E" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mg K/kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x20" flags="0x30">
    <title>VE / Airflow model at cam phase 25 deg (bank 5 of 5)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam-phase VE bank for 25 deg cam. Dormant at idle and light load on the stock H3; probably used under load above about 2000 rpm, where a load-based path commands 9 to 11 desired-cam degrees (between banks 4 and 5 on this axis) (E0358, not yet confirmed on the road). Used when the cam is phased toward 25 deg, Check a loaded log before assuming edits here do nothing. Cam axis note: the PCM halves its actual cam reading before comparing it with desired cam, so this axis counts twice as many units per degree as the desired-cam items in this file (the load-based target of 9 to 11 desired-cam degrees sits at about 18 to 22 her...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="15" />
      <LABEL index="1" value="20.625" />
      <LABEL index="2" value="26.25" />
      <LABEL index="3" value="31.875" />
      <LABEL index="4" value="37.5" />
      <LABEL index="5" value="43.125" />
      <LABEL index="6" value="48.75" />
      <LABEL index="7" value="54.375" />
      <LABEL index="8" value="60" />
      <LABEL index="9" value="65.625" />
      <LABEL index="10" value="71.25" />
      <LABEL index="11" value="76.875" />
      <LABEL index="12" value="82.5" />
      <LABEL index="13" value="88.125" />
      <LABEL index="14" value="93.75" />
      <LABEL index="15" value="99.375" />
      <LABEL index="16" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2BB76" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mg K/kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x21" flags="0x30">
    <title>VE bank cam-phase axis breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The third axis of the VE model: five cam-phase breakpoints, stock 0, 9, 12, 16, 25 on the actual-cam scale. Entry i pairs with VE bank entry i. The PCM clamps the current cam angle between the first and last and interpolates between the bracketing tables. Cam axis note: the PCM halves its actual cam reading before comparing it with desired cam, so this axis counts twice as many units per degree as the desired-cam items in this file (the load-based target of 9 to 11 desired-cam degrees sits at about 18 to 22 here). The degree labels on this axis are on the actual-cam scale, most likely crank degrees. Evidence: ledger:E0081, le...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B1F6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x22" flags="0x0">
    <title>VE Model Mode Switch (DO NOT TUNE)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 1 = the VE airflow model blends its five cam-phase banks. 0 = the PCM uses bank 1 only. Changes which airflow model runs. Effect: DO NOT TUNE (selects the airflow model) Evidence: ledger:E0081, ledger:E0083, ledger:E0151</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x230C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x23" flags="0x0">
    <title>VE Model Cam Axis Source Switch (DO NOT TUNE)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 0 = the VE banks are indexed by the PCM&#x27;s primary actual-cam reading; non-zero switches to its alternate reading. Changes which signal drives the VE blend. Effect: DO NOT TUNE (selects the cam signal) Evidence: ledger:E0081, ledger:E0083, ledger:E0151</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C274" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x24" flags="0x30">
    <title>Octane-learn DECREASE gain vs A-B spark delta</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Octane-learn gain versus the A-B spark delta, 0 to 30 deg. Evidence: ledger:E0012, ledger:E0169, ledger:E0204</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>31</indexcount>
      <units>deg (high - low octane spark)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AE56" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="31" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x25" flags="0x30">
    <title>Octane-learn INCREASE gain vs per-cylinder knock retard</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Octane-learn gain versus knock retard, 0 to 20 deg; stock flat 0.10. Evidence: ledger:E0013, ledger:E0204, ledger:E0218, ledger:E0260</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>deg (per-cylinder knock retard)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="4" />
      <LABEL index="3" value="6" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="12" />
      <LABEL index="7" value="14" />
      <LABEL index="8" value="16" />
      <LABEL index="9" value="18" />
      <LABEL index="10" value="20" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AE3C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x26" flags="0x0">
    <title>Cylinder Count (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of cylinders: the count word that heads the firing order list and bounds the per-cylinder loops (knock, octane learn and others). Stock 5. Structural, not a tuning value. Do not edit. Effect: DO NOT EDIT Evidence: ledger:E0011, ledger:E0153, ledger:E1573</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x239EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cylinders</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x27" flags="0x30">
    <title>Injector flow-rate modifier (Q14) - vs battery voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Q14 multiplier on injector flow (effective flow = flow x X/16384). Stock: all 1.0 (no correction). Evidence: ledger:E0142, ledger:E0162, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>V (system voltage)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="5" />
      <LABEL index="1" value="6" />
      <LABEL index="2" value="7" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="9" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="11" />
      <LABEL index="7" value="12" />
      <LABEL index="8" value="13" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26670" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>3.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x28" flags="0x0">
    <title>Minimum RPM to allow DFCO</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum RPM to allow DFCO Evidence: ledger:E0146, ledger:E0151, ledger:E0236</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2F4D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x29" flags="0x0">
    <title>Maximum RPM to disable DFCO</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Maximum RPM to disable DFCO Evidence: ledger:E0146, ledger:E0151, ledger:E0236</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2F4D4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A" flags="0x0">
    <title>Dynamic Airflow MAF-Only - Engine Speed On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Dynamic airflow MAF-only mode: above the disable engine speed the cylinder airmass comes straight from the MAF (filtered), skipping the airmass predictor and its VE Maximum cap; it switches back below the re-enable engine speed. Below it, the airmass is capped at VE Maximum x barometric pressure / charge temperature, which holds boosted airmass near a naturally aspirated charge, so a boost tune either lowers this engine speed or raises VE Maximum. This is the engine speed at or above which MAF-only mode turns on. Stock 5000 rpm. Effect: lower = MAF-only airmass (no VE Maximum cap) from a lower engine speed; the usual boost ch...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2B1E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B" flags="0x0">
    <title>Dynamic Airflow MAF-Only - Engine Speed Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Dynamic airflow MAF-only mode: above the disable engine speed the cylinder airmass comes straight from the MAF (filtered), skipping the airmass predictor and its VE Maximum cap; it switches back below the re-enable engine speed. Below it, the airmass is capped at VE Maximum x barometric pressure / charge temperature, which holds boosted airmass near a naturally aspirated charge, so a boost tune either lowers this engine speed or raises VE Maximum. This is the engine speed below which MAF-only mode turns off again. Stock 4900 rpm. Keep it a little below the on speed. Effect: lower = MAF-only mode holds down to a lower engine s...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2B1E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C" flags="0x0">
    <title>Power Enrichment Minimum MAP</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Manifold pressure at or above which power enrichment is allowed (with the throttle and rpm conditions). There is no upper limit, so it stays allowed at any boost level. Stock 55 kPa. Effect: lower = power enrichment allowed at lighter load Evidence: ledger:E0147, ledger:E0151, ledger:E0236, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28BA2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D" flags="0x0">
    <title>Power Enrichment Minimum MAP Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once power enrichment is active, the minimum manifold pressure drops by this much, so it stays on until pressure falls this far below the minimum. Stock 5 kPa. Effect: raise = power enrichment holds on at lower manifold pressure Evidence: ledger:E0147, ledger:E0151, ledger:E0236, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28BA4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E" flags="0x0">
    <title>Power Enrichment Delay RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Power enrichment delay applies only at or below this engine speed. Stock 8000 rpm, so the delay rules below apply across the whole range. Effect: lower = no power enrichment delay above this rpm Evidence: ledger:E0147, ledger:E0151, ledger:E0236, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28BAA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F" flags="0x0">
    <title>Power Enrichment minimum RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at or above which power enrichment is allowed. Stock 0 rpm (no rpm limit). Effect: raise = no power enrichment below this rpm Evidence: ledger:E0147, ledger:E0151, ledger:E0194, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28B9E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x30" flags="0x0">
    <title>Power Enrichment minimum RPM hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once power enrichment is active, the minimum rpm drops by this much. Stock 0 rpm. Effect: raise = power enrichment holds on to a lower rpm once active Evidence: ledger:E0147, ledger:E0151, ledger:E0194, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28B9C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x31" flags="0x30">
    <title>VE Maximum (Airmass Cap)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below the dynamic airflow MAF-only engine speed (stock 5000 rpm), the cylinder airmass that spark and fuel use is capped at this maximum VE x barometric pressure / charge temperature x the limit multiplier (and x the learned MAF to VE ratio when that is above 1.0). Barometric pressure, not MAP, so under boost this cap holds the airmass near a naturally aspirated full charge whatever the MAF reads: stock about 0.70 g per cylinder at 2000 rpm and 0.84 g at 5000 rpm (100 kPa, 20 C). Above the MAF-only engine speed the cap is skipped. Same unit as the VE banks: 2439 = 100 % volumetric efficiency on this engine. Raise for boost, o...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C486" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mg K/kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X*0.0625"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x32" flags="0x30">
    <title>Cranking FA Mult Stage 1 vs. Cranking Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Evidence: ledger:E0148, ledger:E0162, ledger:E0163, ledger:E0167, ledger:E0196, ledger:E0213, ledger:E0221, ledger:E0236, ledger:E0257, ledger:E0260, ledger:E0785, ledger:E1329</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>s (engine-off soak time)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="60" />
      <LABEL index="2" value="120" />
      <LABEL index="3" value="180" />
      <LABEL index="4" value="240" />
      <LABEL index="5" value="300" />
      <LABEL index="6" value="360" />
      <LABEL index="7" value="420" />
      <LABEL index="8" value="480" />
      <LABEL index="9" value="540" />
      <LABEL index="10" value="600" />
      <LABEL index="11" value="1800" />
      <LABEL index="12" value="3600" />
      <LABEL index="13" value="7200" />
      <LABEL index="14" value="10800" />
      <LABEL index="15" value="14400" />
      <LABEL index="16" value="21600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x26CE4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26A70" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X*0.0009765625"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x33" flags="0x30">
    <title>Open Loop EQ Ratio Min vs. ECT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Evidence: ledger:E0148, ledger:E0160, ledger:E0175, ledger:E0196, ledger:E0236, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x27022" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X*0.0009765625"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x34" flags="0x30">
    <title>Closed Loop O2 Ready ECT vs. Startup Coolant Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Axis variable is the startup-ECT snapshot. One cold start is consistent: 23.9 C startup predicts 28.4 C, and trims first moved between 27.2 and 28.9 C (2026-09-20 log). Trim activity is a proxy for closed loop; one start only. Evidence: ledger:E0148, ledger:E0164, ledger:E0172, ledger:E0175, ledger:E0236, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant at start)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28F2A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>3</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x35" flags="0x30">
    <title>Burst Knock Retard Mult vs. IAT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Evidence: ledger:E0148, ledger:E0160, ledger:E0172, ledger:E0175, ledger:E0234, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (intake air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AD22" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X*0.000030517578125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x36" flags="0x30">
    <title>Knock Retard Amount</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Evidence: ledger:E0148, ledger:E0160, ledger:E0175, ledger:E0196, ledger:E0234, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2ABB0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>deg</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X*0.0001220703125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x37" flags="0x30">
    <title>Knock Retard Amount ECT Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the knock retard step by coolant temperature (1.0 = no change). The step itself grows with the knock sensor&#x27;s intensity, so this sets how hard the PCM pulls timing per knock event at each temperature. Evidence: ledger:E0148, ledger:E0160, ledger:E0175, ledger:E0196, ledger:E0234, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2ABD4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X*0.000030517578125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x38" flags="0x30">
    <title>Maximum Knock Retard vs. RPM vs. MAP</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Evidence: ledger:E0148, ledger:E0166, ledger:E0196, ledger:E0213, ledger:E0234, ledger:E0257, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="20" />
      <LABEL index="1" value="30" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="50" />
      <LABEL index="4" value="60" />
      <LABEL index="5" value="70" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="90" />
      <LABEL index="8" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AC07" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x39" flags="0x30">
    <title>Retard vs. % Torque Reduction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Evidence: ledger:E0148, ledger:E0167, ledger:E0175, ledger:E0196, ledger:E0234, ledger:E0243, ledger:E0936</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>% torque reduction</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="3.125" />
      <LABEL index="2" value="6.25" />
      <LABEL index="3" value="9.375" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="15.625" />
      <LABEL index="6" value="18.75" />
      <LABEL index="7" value="21.875" />
      <LABEL index="8" value="25" />
      <LABEL index="9" value="28.125" />
      <LABEL index="10" value="31.25" />
      <LABEL index="11" value="34.375" />
      <LABEL index="12" value="37.5" />
      <LABEL index="13" value="40.625" />
      <LABEL index="14" value="43.75" />
      <LABEL index="15" value="46.875" />
      <LABEL index="16" value="50" />
      <LABEL index="17" value="53.125" />
      <LABEL index="18" value="56.25" />
      <LABEL index="19" value="59.375" />
      <LABEL index="20" value="62.5" />
      <LABEL index="21" value="65.625" />
      <LABEL index="22" value="68.75" />
      <LABEL index="23" value="71.875" />
      <LABEL index="24" value="75" />
      <LABEL index="25" value="78.125" />
      <LABEL index="26" value="81.25" />
      <LABEL index="27" value="84.375" />
      <LABEL index="28" value="87.5" />
      <LABEL index="29" value="90.625" />
      <LABEL index="30" value="93.75" />
      <LABEL index="31" value="96.875" />
      <LABEL index="32" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3191E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3A" flags="0x30">
    <title>AC Compressor Torque vs. AC Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque model: A/C compressor torque by engine speed and A/C head pressure. It is added to the second A/C torque table (by intake air temperature); the sum is the compressor torque counted as an accessory load while the A/C clutch is on. Effect: raise = more engine torque is allowed for the A/C compressor Evidence: ledger:E0148, ledger:E0167, ledger:E0196, ledger:E0213, ledger:E0236, ledger:E0242, ledger:E0243, ledger:E0257, ledger:E0260, ledger:E1114, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (A/C pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="225" />
      <LABEL index="2" value="450" />
      <LABEL index="3" value="675" />
      <LABEL index="4" value="900" />
      <LABEL index="5" value="1125" />
      <LABEL index="6" value="1350" />
      <LABEL index="7" value="1575" />
      <LABEL index="8" value="1800" />
      <LABEL index="9" value="2025" />
      <LABEL index="10" value="2250" />
      <LABEL index="11" value="2475" />
      <LABEL index="12" value="2700" />
      <LABEL index="13" value="2925" />
      <LABEL index="14" value="3150" />
      <LABEL index="15" value="3375" />
      <LABEL index="16" value="3600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="400" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1200" />
      <LABEL index="4" value="1600" />
      <LABEL index="5" value="2000" />
      <LABEL index="6" value="2400" />
      <LABEL index="7" value="2800" />
      <LABEL index="8" value="3200" />
      <LABEL index="9" value="3600" />
      <LABEL index="10" value="4000" />
      <LABEL index="11" value="4400" />
      <LABEL index="12" value="4800" />
      <LABEL index="13" value="5200" />
      <LABEL index="14" value="5600" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x303D6" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>lb-ft</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6042.016932</max>
      <MATH equation="X*0.0921952686597"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3B" flags="0x30">
    <title>TCC DC Maximum vs. Line Pressure vs. Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Evidence: ledger:E0148, ledger:E0164, ledger:E0196, ledger:E0236, ledger:E0257, ledger:E0260, ledger:E1352</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (trans fluid)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16.5" />
      <LABEL index="2" value="33" />
      <LABEL index="3" value="49.5" />
      <LABEL index="4" value="66" />
      <LABEL index="5" value="82.5" />
      <LABEL index="6" value="99" />
      <LABEL index="7" value="115.5" />
      <LABEL index="8" value="132" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>kPa (line pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="80" />
      <LABEL index="2" value="160" />
      <LABEL index="3" value="240" />
      <LABEL index="4" value="320" />
      <LABEL index="5" value="400" />
      <LABEL index="6" value="480" />
      <LABEL index="7" value="560" />
      <LABEL index="8" value="640" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DC59" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>99.609375</max>
      <MATH equation="X*0.390625"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3C" flags="0x30">
    <title>TCC DC Minimum vs. Line Pressure vs. Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Evidence: ledger:E0148, ledger:E0164, ledger:E0196, ledger:E0236, ledger:E0257, ledger:E0260, ledger:E1352</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (trans fluid)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16.5" />
      <LABEL index="2" value="33" />
      <LABEL index="3" value="49.5" />
      <LABEL index="4" value="66" />
      <LABEL index="5" value="82.5" />
      <LABEL index="6" value="99" />
      <LABEL index="7" value="115.5" />
      <LABEL index="8" value="132" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>kPa (line pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="80" />
      <LABEL index="2" value="160" />
      <LABEL index="3" value="240" />
      <LABEL index="4" value="320" />
      <LABEL index="5" value="400" />
      <LABEL index="6" value="480" />
      <LABEL index="7" value="560" />
      <LABEL index="8" value="640" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DC01" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>99.609375</max>
      <MATH equation="X*0.390625"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3D" flags="0x30">
    <title>EGR Spark Advance Correction - Add</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark added from the EGR spark correction table is scaled by the cam-phase factor (Cam-Phase Factor vs Cam Angle and RPM) divided by a normaliser (stock 0.24, the factor table&#x27;s largest value), so the table applies in full at 24 degrees of cam and in proportion below it. Table by cylinder airmass and engine speed; stock up to 16 degrees at light load (0.08 to 0.48 g per cylinder) and 0 at higher airmass. With the stock cam at 9 to 11 degrees under load about 16 percent of the table is applied. The result rises at half the difference per update and falls at once. Effect: raise = more spark at that airmass and speed while...</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="800" />
      <LABEL index="1" value="1200" />
      <LABEL index="2" value="1600" />
      <LABEL index="3" value="2000" />
      <LABEL index="4" value="2400" />
      <LABEL index="5" value="2800" />
      <LABEL index="6" value="3200" />
      <LABEL index="7" value="3600" />
      <LABEL index="8" value="4000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl (cylinder airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2DB11" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E" flags="0x30">
    <title>Base Dwell Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Placed on the H3 by code-layout prediction. Evidence: ledger:E0150, ledger:E0165, ledger:E0175, ledger:E0196, ledger:E0213, ledger:E0234, ledger:E0257, ledger:E0260, ledger:E1358</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>22</indexcount>
      <units>V (ignition)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="4.5" />
      <LABEL index="1" value="5.5" />
      <LABEL index="2" value="6.5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="8.5" />
      <LABEL index="5" value="9.5" />
      <LABEL index="6" value="10.5" />
      <LABEL index="7" value="11.5" />
      <LABEL index="8" value="12.5" />
      <LABEL index="9" value="13.5" />
      <LABEL index="10" value="14.5" />
      <LABEL index="11" value="15.5" />
      <LABEL index="12" value="16.5" />
      <LABEL index="13" value="17.5" />
      <LABEL index="14" value="18.5" />
      <LABEL index="15" value="19.5" />
      <LABEL index="16" value="20.5" />
      <LABEL index="17" value="21.5" />
      <LABEL index="18" value="22.5" />
      <LABEL index="19" value="23.5" />
      <LABEL index="20" value="24.5" />
      <LABEL index="21" value="25.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F65A" mmedelementsizebits="16" mmedrowcount="22" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ms</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3F" flags="0x30">
    <title>Base Dwell Time Modifier vs. IGNV vs. ECT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Placed on the H3 by code-layout prediction. Column axis is a modelled temperature (mostly coolant, pulled down by IAT and vehicle speed), not raw coolant (E0258). Evidence: ledger:E0150, ledger:E0165, ledger:E0175, ledger:E0196, ledger:E0234, ledger:E0257, ledger:E0258, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>degC (modelled temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <LABEL index="9" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>22</indexcount>
      <units>V (ignition)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="4.5" />
      <LABEL index="1" value="5.5" />
      <LABEL index="2" value="6.5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="8.5" />
      <LABEL index="5" value="9.5" />
      <LABEL index="6" value="10.5" />
      <LABEL index="7" value="11.5" />
      <LABEL index="8" value="12.5" />
      <LABEL index="9" value="13.5" />
      <LABEL index="10" value="14.5" />
      <LABEL index="11" value="15.5" />
      <LABEL index="12" value="16.5" />
      <LABEL index="13" value="17.5" />
      <LABEL index="14" value="18.5" />
      <LABEL index="15" value="19.5" />
      <LABEL index="16" value="20.5" />
      <LABEL index="17" value="21.5" />
      <LABEL index="18" value="22.5" />
      <LABEL index="19" value="23.5" />
      <LABEL index="20" value="24.5" />
      <LABEL index="21" value="25.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F949" mmedelementsizebits="8" mmedrowcount="22" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>0.996094</max>
      <MATH equation="X*0.00390625"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x40" flags="0x30">
    <title>Burst Knock Retard Mult vs. RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Placed on the H3 by code-layout prediction. Evidence: ledger:E0150, ledger:E0160, ledger:E0172, ledger:E0175, ledger:E0196, ledger:E0234, ledger:E0260</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AD4A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X*0.0000152587890625"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x41" flags="0x30">
    <title>Burst Knock Retard vs. Cylair Delta</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Placed on the H3 by code-layout prediction. Evidence: ledger:E0150, ledger:E0167, ledger:E0196, ledger:E0234, ledger:E0936</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/cyl (airmass rise)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.002" />
      <LABEL index="2" value="0.004" />
      <LABEL index="3" value="0.006" />
      <LABEL index="4" value="0.008" />
      <LABEL index="5" value="0.01" />
      <LABEL index="6" value="0.012" />
      <LABEL index="7" value="0.014" />
      <LABEL index="8" value="0.016" />
      <LABEL index="9" value="0.018" />
      <LABEL index="10" value="0.02" />
      <LABEL index="11" value="0.022" />
      <LABEL index="12" value="0.024" />
      <LABEL index="13" value="0.026" />
      <LABEL index="14" value="0.028" />
      <LABEL index="15" value="0.03" />
      <LABEL index="16" value="0.032" />
      <LABEL index="17" value="0.034" />
      <LABEL index="18" value="0.036" />
      <LABEL index="19" value="0.038" />
      <LABEL index="20" value="0.04" />
      <LABEL index="21" value="0.042" />
      <LABEL index="22" value="0.044" />
      <LABEL index="23" value="0.046" />
      <LABEL index="24" value="0.048" />
      <LABEL index="25" value="0.05" />
      <LABEL index="26" value="0.052" />
      <LABEL index="27" value="0.054" />
      <LABEL index="28" value="0.056" />
      <LABEL index="29" value="0.058" />
      <LABEL index="30" value="0.06" />
      <LABEL index="31" value="0.062" />
      <LABEL index="32" value="0.064" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2ACDE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x42" flags="0x30">
    <title>Knock Retard Amount Baro Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the knock retard step by barometric pressure (1.0 = no change). The step itself grows with the knock sensor&#x27;s intensity, so this sets how hard the PCM pulls timing per knock event at each altitude. Evidence: ledger:E0150, ledger:E0162, ledger:E0175, ledger:E0196, ledger:E0234, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="55" />
      <LABEL index="1" value="65" />
      <LABEL index="2" value="75" />
      <LABEL index="3" value="85" />
      <LABEL index="4" value="95" />
      <LABEL index="5" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2ABF8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X*0.000030517578125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x43" flags="0x30">
    <title>Idle Underspeed Spark vs. RPM Error (P/N)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Placed on the H3 by code-layout prediction; under/over role confirmed by value sign, P/N vs In Gear by layout order only. Used in Park/Neutral only; in gear the In Gear curve applies (E0288). Scaled by Idle Underspeed Spark Gain vs Coolant (E0291). Evidence: ledger:E0150, ledger:E0161, ledger:E0196, ledger:E0288, ledger:E0936</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm error (x0.75 in most modes)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <LABEL index="9" value="144" />
      <LABEL index="10" value="160" />
      <LABEL index="11" value="176" />
      <LABEL index="12" value="192" />
      <LABEL index="13" value="208" />
      <LABEL index="14" value="224" />
      <LABEL index="15" value="240" />
      <LABEL index="16" value="256" />
      <LABEL index="17" value="272" />
      <LABEL index="18" value="288" />
      <LABEL index="19" value="304" />
      <LABEL index="20" value="320" />
      <LABEL index="21" value="336" />
      <LABEL index="22" value="352" />
      <LABEL index="23" value="368" />
      <LABEL index="24" value="384" />
      <LABEL index="25" value="400" />
      <LABEL index="26" value="416" />
      <LABEL index="27" value="432" />
      <LABEL index="28" value="448" />
      <LABEL index="29" value="464" />
      <LABEL index="30" value="480" />
      <LABEL index="31" value="496" />
      <LABEL index="32" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EB48" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x44" flags="0x30">
    <title>Idle Overspeed Spark vs. RPM Error (P/N)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Placed on the H3 by code-layout prediction; under/over role confirmed by value sign, P/N vs In Gear by layout order only. Used in Park/Neutral only; in gear the In Gear curve applies (E0288). Scaled by Idle Overspeed Spark / Droop Airflow Gain vs Coolant (E0291). Evidence: ledger:E0150, ledger:E0161, ledger:E0196, ledger:E0288</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm error (x0.75 in most modes)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <LABEL index="9" value="144" />
      <LABEL index="10" value="160" />
      <LABEL index="11" value="176" />
      <LABEL index="12" value="192" />
      <LABEL index="13" value="208" />
      <LABEL index="14" value="224" />
      <LABEL index="15" value="240" />
      <LABEL index="16" value="256" />
      <LABEL index="17" value="272" />
      <LABEL index="18" value="288" />
      <LABEL index="19" value="304" />
      <LABEL index="20" value="320" />
      <LABEL index="21" value="336" />
      <LABEL index="22" value="352" />
      <LABEL index="23" value="368" />
      <LABEL index="24" value="384" />
      <LABEL index="25" value="400" />
      <LABEL index="26" value="416" />
      <LABEL index="27" value="432" />
      <LABEL index="28" value="448" />
      <LABEL index="29" value="464" />
      <LABEL index="30" value="480" />
      <LABEL index="31" value="496" />
      <LABEL index="32" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EB90" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x45" flags="0x30">
    <title>Idle Underspeed Spark vs. RPM Error (In Gear)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark added when idle rpm is below desired, by rpm error, while the transmission is in gear. Placed by code layout; under / over role confirmed by the sign of the values, In Gear vs Park/Neutral by layout order only. Scaled by Idle Underspeed Spark Gain vs Coolant. Evidence: ledger:E0150, ledger:E0161, ledger:E0196, ledger:E0288, ledger:E0936</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm error (x0.75 in most modes)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <LABEL index="9" value="144" />
      <LABEL index="10" value="160" />
      <LABEL index="11" value="176" />
      <LABEL index="12" value="192" />
      <LABEL index="13" value="208" />
      <LABEL index="14" value="224" />
      <LABEL index="15" value="240" />
      <LABEL index="16" value="256" />
      <LABEL index="17" value="272" />
      <LABEL index="18" value="288" />
      <LABEL index="19" value="304" />
      <LABEL index="20" value="320" />
      <LABEL index="21" value="336" />
      <LABEL index="22" value="352" />
      <LABEL index="23" value="368" />
      <LABEL index="24" value="384" />
      <LABEL index="25" value="400" />
      <LABEL index="26" value="416" />
      <LABEL index="27" value="432" />
      <LABEL index="28" value="448" />
      <LABEL index="29" value="464" />
      <LABEL index="30" value="480" />
      <LABEL index="31" value="496" />
      <LABEL index="32" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EBD8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x46" flags="0x30">
    <title>Idle Overspeed Spark vs. RPM Error (In Gear)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark removed when idle rpm is above desired, by rpm error, while the transmission is in gear. Placed by code layout; under / over role confirmed by the sign of the values, In Gear vs Park/Neutral by layout order only. Scaled by Idle Overspeed Spark / Droop Airflow Gain vs Coolant. Evidence: ledger:E0150, ledger:E0161, ledger:E0196, ledger:E0288</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm error (x0.75 in most modes)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <LABEL index="9" value="144" />
      <LABEL index="10" value="160" />
      <LABEL index="11" value="176" />
      <LABEL index="12" value="192" />
      <LABEL index="13" value="208" />
      <LABEL index="14" value="224" />
      <LABEL index="15" value="240" />
      <LABEL index="16" value="256" />
      <LABEL index="17" value="272" />
      <LABEL index="18" value="288" />
      <LABEL index="19" value="304" />
      <LABEL index="20" value="320" />
      <LABEL index="21" value="336" />
      <LABEL index="22" value="352" />
      <LABEL index="23" value="368" />
      <LABEL index="24" value="384" />
      <LABEL index="25" value="400" />
      <LABEL index="26" value="416" />
      <LABEL index="27" value="432" />
      <LABEL index="28" value="448" />
      <LABEL index="29" value="464" />
      <LABEL index="30" value="480" />
      <LABEL index="31" value="496" />
      <LABEL index="32" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EC20" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x47" flags="0x30">
    <title>Force motor (PCS) current vs commanded line pressure - used while pressure RISING</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0050, ledger:E0059, ledger:E0124, ledger:E0125, ledger:E0135, ledger:E0168, ledger:E0174, ledger:E1362</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (commanded line pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="40" />
      <LABEL index="2" value="80" />
      <LABEL index="3" value="120" />
      <LABEL index="4" value="160" />
      <LABEL index="5" value="200" />
      <LABEL index="6" value="240" />
      <LABEL index="7" value="280" />
      <LABEL index="8" value="320" />
      <LABEL index="9" value="360" />
      <LABEL index="10" value="400" />
      <LABEL index="11" value="440" />
      <LABEL index="12" value="480" />
      <LABEL index="13" value="520" />
      <LABEL index="14" value="560" />
      <LABEL index="15" value="600" />
      <LABEL index="16" value="640" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC (trans fluid)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DF9F" mmedelementsizebits="8" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>A</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x48" flags="0x30">
    <title>Shift Speed vs TPS - Hot Transmission</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 speeds]; COUNT is a structure word - never edit it (E0176). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed at which each up/downshift is scheduled vs throttle, Hot Transmission schedule. 311 mph = shift inhibited at that throttle. Axis = the PCM&#x27;s shift throttle: driver throttle-area demand above idle through a curve, close to throttle % above idle. The PCM uses the Hot schedules while hot transmission mode is on; hot mode takes priority over cruise and 4-Lo. Effect: raise = hold gears longer; keep each downshift below its upshift (hysteresis) Evidence: ledger:E0176, ledger:E0208, ledger:E0269, ledger:E0838, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="37" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="87" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2 up" />
      <LABEL index="1" value="2-3 up" />
      <LABEL index="2" value="3-4 up" />
      <LABEL index="3" value="2-1 down" />
      <LABEL index="4" value="3-2 down" />
      <LABEL index="5" value="4-3 down" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x398CC" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x49" flags="0x30">
    <title>Shift Speed vs TPS - Cruise</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 speeds]; COUNT is a structure word - never edit it (E0176). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed at which each up/downshift is scheduled vs throttle, Cruise schedule. 311 mph = shift inhibited at that throttle. Axis = the PCM&#x27;s shift throttle: driver throttle-area demand above idle through a curve, close to throttle % above idle. The PCM uses the Cruise schedules while cruise control is engaged; cruise takes priority over 4-Lo. Effect: raise = hold gears longer; keep each downshift below its upshift (hysteresis) Evidence: ledger:E0176, ledger:E0208, ledger:E0269, ledger:E0838, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="37" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="87" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2 up" />
      <LABEL index="1" value="2-3 up" />
      <LABEL index="2" value="3-4 up" />
      <LABEL index="3" value="2-1 down" />
      <LABEL index="4" value="3-2 down" />
      <LABEL index="5" value="4-3 down" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39A46" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4A" flags="0x30">
    <title>Shift Speed vs TPS - 4-Lo</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 speeds]; COUNT is a structure word - never edit it (E0176). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed at which each up/downshift is scheduled vs throttle, 4-Lo schedule. 311 mph = shift inhibited at that throttle. Axis = the PCM&#x27;s shift throttle: driver throttle-area demand above idle through a curve, close to throttle % above idle. The PCM uses these schedules while the transfer case is in 4-Lo (named Performance before v3.7; the stock calibration has no separate performance mode). In 4-Lo the transmission&#x27;s speed reading is 4.03 times road speed (it is worked out from transmission output speed with the high-ra...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="37" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="87" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2 up" />
      <LABEL index="1" value="2-3 up" />
      <LABEL index="2" value="3-4 up" />
      <LABEL index="3" value="2-1 down" />
      <LABEL index="4" value="3-2 down" />
      <LABEL index="5" value="4-3 down" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39B54" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4B" flags="0x30">
    <title>TCC Apply/Release Speed vs TPS - Normal</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 speeds]; COUNT is a structure word - never edit it (E0177). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed above which the torque converter clutch applies / below which it releases, per gear vs throttle, Normal mode. 311/308 mph = never. Axis = the PCM&#x27;s shift throttle: driver throttle-area demand above idle through a curve, close to throttle % above idle. The PCM uses the Normal schedules in ordinary driving: not in hot transmission mode, cruise or 4-Lo. Effect: keep release below apply (hysteresis); lower apply = earlier lockup Evidence: ledger:E0177, ledger:E0208, ledger:E0269, ledger:E0838, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="37" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="87" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd Apply" />
      <LABEL index="1" value="3rd Apply" />
      <LABEL index="2" value="4th Apply" />
      <LABEL index="3" value="2nd Release" />
      <LABEL index="4" value="3rd Release" />
      <LABEL index="5" value="4th Release" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D7DE" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4C" flags="0x30">
    <title>TCC Apply/Release Speed vs TPS - Hot Transmission</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 speeds]; COUNT is a structure word - never edit it (E0177). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed above which the torque converter clutch applies / below which it releases, per gear vs throttle, Hot Transmission mode. 311/308 mph = never. Axis = the PCM&#x27;s shift throttle: driver throttle-area demand above idle through a curve, close to throttle % above idle. The PCM uses the Hot schedules while hot transmission mode is on; hot mode takes priority over cruise and 4-Lo. Effect: keep release below apply (hysteresis); lower apply = earlier lockup Evidence: ledger:E0177, ledger:E0208, ledger:E0269, ledger:E0838, ledger...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="37" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="87" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd Apply" />
      <LABEL index="1" value="3rd Apply" />
      <LABEL index="2" value="4th Apply" />
      <LABEL index="3" value="2nd Release" />
      <LABEL index="4" value="3rd Release" />
      <LABEL index="5" value="4th Release" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D69A" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4D" flags="0x30">
    <title>TCC Apply/Release Speed vs TPS - Cruise</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 speeds]; COUNT is a structure word - never edit it (E0177). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed above which the torque converter clutch applies / below which it releases, per gear vs throttle, Cruise mode. 311/308 mph = never. Axis = the PCM&#x27;s shift throttle: driver throttle-area demand above idle through a curve, close to throttle % above idle. The PCM uses the Cruise schedules while cruise control is engaged; cruise takes priority over 4-Lo. Effect: keep release below apply (hysteresis); lower apply = earlier lockup Evidence: ledger:E0177, ledger:E0208, ledger:E0269, ledger:E0838, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="37" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="87" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd Apply" />
      <LABEL index="1" value="3rd Apply" />
      <LABEL index="2" value="4th Apply" />
      <LABEL index="3" value="2nd Release" />
      <LABEL index="4" value="3rd Release" />
      <LABEL index="5" value="4th Release" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D96A" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E" flags="0x30">
    <title>TCC Apply/Release Speed vs TPS - 4-Lo</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 speeds]; COUNT is a structure word - never edit it (E0177). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed above which the torque converter clutch applies / below which it releases, per gear vs throttle, 4-Lo. 311/308 mph = never. Axis = the PCM&#x27;s shift throttle: driver throttle-area demand above idle through a curve, close to throttle % above idle. The PCM uses these schedules while the transfer case is in 4-Lo (named Performance before v3.7; the stock calibration has no separate performance mode). In 4-Lo the transmission&#x27;s speed reading is 4.03 times road speed (it is worked out from transmission output speed with...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="37" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="87" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd Apply" />
      <LABEL index="1" value="3rd Apply" />
      <LABEL index="2" value="4th Apply" />
      <LABEL index="3" value="2nd Release" />
      <LABEL index="4" value="3rd Release" />
      <LABEL index="5" value="4th Release" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DAAE" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4F" flags="0x30">
    <title>DFCO Entry Spark</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark used on entry to decel fuel cut-off, vs airmass and rpm. Every cell is 0 deg on the stock H3 (not used by this calibration) (E0178). Effect: stock H3 = 0 everywhere; leave as is Evidence: ledger:E0178, ledger:E0210, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.20" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.40" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F519" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x50" flags="0x30">
    <title>Misfire Detection Threshold - Cylinder Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor, cylinder mode: the PCM times each crank segment (one cylinder&#x27;s share of rotation) and looks at how far one segment departs from the trend of its neighbours (a third difference of consecutive segment times). A departure at or above this many microseconds is taken as a misfire of that cylinder. Rows are load (0 to 100 %), columns engine speed (400 to 7000 rpm); the value is interpolated. A raw value of 32767 (16000 us) in a cell or its neighbours switches this mode off there. Stock uses cylinder mode from 400 to below 1200 rpm and revolution mode from 1200 to below 6500 rpm. Effect: lower = smaller crank...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x368F4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>26</indexcount>
      <units>rpm</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>% load</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6" />
      <LABEL index="2" value="12" />
      <LABEL index="3" value="19" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31" />
      <LABEL index="6" value="37" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56" />
      <LABEL index="10" value="62" />
      <LABEL index="11" value="69" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81" />
      <LABEL index="14" value="87" />
      <LABEL index="15" value="94" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3692E" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>us</units>
      <decimalpl>1</decimalpl>
      <min>-16000.000000</min>
      <max>15999.511719</max>
      <MATH equation="X/2.048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x51" flags="0x30">
    <title>Misfire Detection Threshold - Revolution Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor, revolution mode (used at higher engine speed): a combined measure of crank segment time disturbance across a revolution, in microseconds of segment time. A value at or above this threshold is taken as a misfire. Rows are load (0 to 100 %), columns engine speed (400 to 7000 rpm); the value is interpolated. A raw value of 32767 (16000 us) in a cell or its neighbours switches this mode off there. Stock uses cylinder mode from 400 to below 1200 rpm and revolution mode from 1200 to below 6500 rpm. Effect: lower = smaller crank speed disturbances are counted as misfires (more sensitive) Evidence: ledger:E0179, ledg...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x368F4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>26</indexcount>
      <units>rpm</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>% load</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6" />
      <LABEL index="2" value="12" />
      <LABEL index="3" value="19" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31" />
      <LABEL index="6" value="37" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56" />
      <LABEL index="10" value="62" />
      <LABEL index="11" value="69" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81" />
      <LABEL index="14" value="87" />
      <LABEL index="15" value="94" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36CA6" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>us</units>
      <decimalpl>1</decimalpl>
      <min>-16000.000000</min>
      <max>15999.511719</max>
      <MATH equation="X/2.048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x52" flags="0x30">
    <title>TCC WOT Apply/Release Speed - Normal</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 2][2 values]; COUNT is a structure word - never edit it (E0180). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. TCC apply/release speeds in the WOT mode of the Normal schedule. 311/308 mph = never. Axis = the PCM&#x27;s shift throttle: driver throttle-area demand above idle through a curve, close to throttle % above idle. The PCM uses the Normal schedules in ordinary driving: not in hot transmission mode, cruise or 4-Lo. The wide-open-throttle set applies while pedal demand is above the high pedal set point (stock 96.9 %, 56.3 % in 4-Lo, 99 % with cruise engaged). Effect: WOT shift behaviour - change in small steps Evidence: ledger:E0180, ledger:E...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd Apply" />
      <LABEL index="1" value="3rd Apply" />
      <LABEL index="2" value="4th Apply" />
      <LABEL index="3" value="2nd Release" />
      <LABEL index="4" value="3rd Release" />
      <LABEL index="5" value="4th Release" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D7BA" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x53" flags="0x30">
    <title>WOT Shift Speed - Hot</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 2][2 values]; COUNT is a structure word - never edit it (E0180). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Speed-based shift points used in the WOT mode of the Hot schedule (flat over throttle). 311 mph = no speed-based shift. (E0180) The PCM reads only the 100 column: this lookup runs at a fixed full-throttle input, so editing the 0 column has no effect (E0269). The PCM uses the Hot schedules while hot transmission mode is on; hot mode takes priority over cruise and 4-Lo. The wide-open-throttle set applies while pedal demand is above the high pedal set point (stock 96.9 %, 56.3 % in 4-Lo, 99 % with cruise engaged). Effect: WOT shift behaviou...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2 up" />
      <LABEL index="1" value="2-3 up" />
      <LABEL index="2" value="3-4 up" />
      <LABEL index="3" value="2-1 down" />
      <LABEL index="4" value="3-2 down" />
      <LABEL index="5" value="4-3 down" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x399A4" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x54" flags="0x30">
    <title>TCC WOT Apply/Release Speed - Hot</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 2][2 values]; COUNT is a structure word - never edit it (E0180). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. TCC apply/release speeds in the WOT mode of the Hot schedule. 311/308 mph = never. Axis = the PCM&#x27;s shift throttle: driver throttle-area demand above idle through a curve, close to throttle % above idle. The PCM uses the Hot schedules while hot transmission mode is on; hot mode takes priority over cruise and 4-Lo. The wide-open-throttle set applies while pedal demand is above the high pedal set point (stock 96.9 %, 56.3 % in 4-Lo, 99 % with cruise engaged). Effect: WOT shift behaviour - change in small steps Evidence: ledger:E0180,...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd Apply" />
      <LABEL index="1" value="3rd Apply" />
      <LABEL index="2" value="4th Apply" />
      <LABEL index="3" value="2nd Release" />
      <LABEL index="4" value="3rd Release" />
      <LABEL index="5" value="4th Release" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D676" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x55" flags="0x30">
    <title>WOT Shift RPM - Hot</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 2][2 values]; COUNT is a structure word - never edit it (E0180). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine rpm at which the WOT upshift is commanded, Hot schedule. (E0180) The PCM reads only the 100 column: this lookup runs at a fixed full-throttle input, so editing the 0 column has no effect (E0269). The PCM uses the Hot schedules while hot transmission mode is on; hot mode takes priority over cruise and 4-Lo. The wide-open-throttle set applies while pedal demand is above the high pedal set point (stock 96.9 %, 56.3 % in 4-Lo, 99 % with cruise engaged). Effect: WOT shift behaviour - change in small steps Evidence: ledger:E0180, ledger...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x399C8" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X*0.125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x56" flags="0x30">
    <title>WOT Shift Speed - 4-Lo</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 2][2 values]; COUNT is a structure word - never edit it (E0180). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Speed-based shift points used in the WOT mode of the 4-Lo schedule (flat over throttle). 311 mph = no speed-based shift. (E0180) The PCM reads only the 100 column: this lookup runs at a fixed full-throttle input, so editing the 0 column has no effect (E0269). The PCM uses these schedules while the transfer case is in 4-Lo (named Performance before v3.7; the stock calibration has no separate performance mode). The wide-open-throttle set applies while pedal demand is above the high pedal set point (stock 96.9 %, 56.3 % in 4-Lo, 99 % w...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2 up" />
      <LABEL index="1" value="2-3 up" />
      <LABEL index="2" value="3-4 up" />
      <LABEL index="3" value="2-1 down" />
      <LABEL index="4" value="3-2 down" />
      <LABEL index="5" value="4-3 down" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39C2C" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x57" flags="0x30">
    <title>TCC WOT Apply/Release Speed - 4-Lo</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 2][2 values]; COUNT is a structure word - never edit it (E0180). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. TCC apply/release speeds in the WOT mode of the 4-Lo schedule. 311/308 mph = never. Axis = the PCM&#x27;s shift throttle: driver throttle-area demand above idle through a curve, close to throttle % above idle. The PCM uses these schedules while the transfer case is in 4-Lo (named Performance before v3.7; the stock calibration has no separate performance mode). The wide-open-throttle set applies while pedal demand is above the high pedal set point (stock 96.9 %, 56.3 % in 4-Lo, 99 % with cruise engaged). In 4-Lo the transmission&#x27;s sp...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd Apply" />
      <LABEL index="1" value="3rd Apply" />
      <LABEL index="2" value="4th Apply" />
      <LABEL index="3" value="2nd Release" />
      <LABEL index="4" value="3rd Release" />
      <LABEL index="5" value="4th Release" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DA8A" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x58" flags="0x30">
    <title>WOT Shift RPM - 4-Lo</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 2][2 values]; COUNT is a structure word - never edit it (E0180). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine rpm at which the WOT upshift is commanded, 4-Lo schedule. (E0180) The PCM reads only the 100 column: this lookup runs at a fixed full-throttle input, so editing the 0 column has no effect (E0269). The PCM uses these schedules while the transfer case is in 4-Lo (named Performance before v3.7; the stock calibration has no separate performance mode). The wide-open-throttle set applies while pedal demand is above the high pedal set point (stock 96.9 %, 56.3 % in 4-Lo, 99 % with cruise engaged). Effect: WOT shift behaviour - change in...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39C50" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X*0.125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x59" flags="0x30">
    <title>Closed Loop Enable Coolant vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant temperature needed before closed loop is allowed, vs coolant at start-up. Stock H3 70 C (cold start) .. 55 C (E0184) Effect: raise = later closed loop Evidence: ledger:E0184, ledger:E0210, ledger:E0257, ledger:E0260, ledger:E1329</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28EA0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5A" flags="0x30">
    <title>Closed Loop Enable Delay vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Run time before closed loop is allowed, vs coolant at start-up. Stock H3 60 s cold .. 3 s warm (E0184) Effect: raise = later closed loop Evidence: ledger:E0184, ledger:E0210, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1329</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28E7C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5B" flags="0x30">
    <title>Knock Retard Recovery Rate vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the remaining knock retard that is given back at each update, vs rpm. The update runs four times a second, and every cylinder&#x27;s retard is reduced by this share each time. Stock 25 % up to 1200 rpm and 20 % from 1600 rpm, which leaves about 41 % of the retard after one second at speed. Correction: releases up to v3.16 showed this curve as a time step in seconds, which was wrong. Effect: larger = timing comes back faster after knock; 0 = retard is never given back Evidence: ledger:E0184, ledger:E0210, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1164, ledger:E1166, ledger:E1329</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="400" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1200" />
      <LABEL index="4" value="1600" />
      <LABEL index="5" value="2000" />
      <LABEL index="6" value="2400" />
      <LABEL index="7" value="2800" />
      <LABEL index="8" value="3200" />
      <LABEL index="9" value="3600" />
      <LABEL index="10" value="4000" />
      <LABEL index="11" value="4400" />
      <LABEL index="12" value="4800" />
      <LABEL index="13" value="5200" />
      <LABEL index="14" value="5600" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6400" />
      <LABEL index="17" value="6800" />
      <LABEL index="18" value="7200" />
      <LABEL index="19" value="7600" />
      <LABEL index="20" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2ACA2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% per update</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5C" flags="0x30">
    <title>Minimum Dwell Time Mult vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier giving the minimum allowed coil dwell, vs rpm. Stock H3 0.8 flat (E0184) Effect: leave stock Evidence: ledger:E0184, ledger:E0210, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1358</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2FA3E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5D" flags="0x30">
    <title>PE/COT Spark Advance Correction vs RPM vs EQ</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark added while Power Enrichment / catalyst over-temp enrichment is active, vs rpm and commanded EQ. Stock H3 0..5 deg (E0185) Effect: more = more timing when rich Evidence: ledger:E0185, ledger:E0210, ledger:E0213, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="800" />
      <LABEL index="1" value="1600" />
      <LABEL index="2" value="2400" />
      <LABEL index="3" value="3200" />
      <LABEL index="4" value="4000" />
      <LABEL index="5" value="4800" />
      <LABEL index="6" value="5600" />
      <LABEL index="7" value="6400" />
      <LABEL index="8" value="7200" />
      <LABEL index="9" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>11</indexcount>
      <units>EQ ratio</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1.00" />
      <LABEL index="1" value="1.05" />
      <LABEL index="2" value="1.10" />
      <LABEL index="3" value="1.15" />
      <LABEL index="4" value="1.20" />
      <LABEL index="5" value="1.25" />
      <LABEL index="6" value="1.30" />
      <LABEL index="7" value="1.35" />
      <LABEL index="8" value="1.40" />
      <LABEL index="9" value="1.45" />
      <LABEL index="10" value="1.50" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2DC41" mmedelementsizebits="8" mmedrowcount="11" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5E" flags="0x30">
    <title>Idle Coastdown Spark vs RPM vs Airmass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark used while coasting down toward idle, vs rpm and cylinder airmass. Stock H3 10..27 deg (E0185) Effect: affects decel feel / stall resistance Evidence: ledger:E0185, ledger:E0213, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2ED39" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5F" flags="0x30">
    <title>Injector Offset vs Battery Voltage vs kPa Vacuum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Injector offset by battery voltage (rows) and manifold vacuum (columns), in ms. The engine adds it to the commanded pulse width when it schedules the injector start, counting both on the same clock in the injector timer, so it uses the base pulse width&#x27;s 1/128 ms step. Effect: raise = the injector pulse starts earlier by that much time at that voltage and vacuum Evidence: ledger:E0186, ledger:E0210, ledger:E0213, ledger:E0216, ledger:E0229, ledger:E1162, ledger:E1270</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa vacuum</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>V</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="4.5" />
      <LABEL index="1" value="5.0" />
      <LABEL index="2" value="5.5" />
      <LABEL index="3" value="6.0" />
      <LABEL index="4" value="6.5" />
      <LABEL index="5" value="7.0" />
      <LABEL index="6" value="7.5" />
      <LABEL index="7" value="8.0" />
      <LABEL index="8" value="8.5" />
      <LABEL index="9" value="9.0" />
      <LABEL index="10" value="9.5" />
      <LABEL index="11" value="10.0" />
      <LABEL index="12" value="10.5" />
      <LABEL index="13" value="11.0" />
      <LABEL index="14" value="11.5" />
      <LABEL index="15" value="12.0" />
      <LABEL index="16" value="12.5" />
      <LABEL index="17" value="13.0" />
      <LABEL index="18" value="13.5" />
      <LABEL index="19" value="14.0" />
      <LABEL index="20" value="14.5" />
      <LABEL index="21" value="15.0" />
      <LABEL index="22" value="15.5" />
      <LABEL index="23" value="16.0" />
      <LABEL index="24" value="16.5" />
      <LABEL index="25" value="17.0" />
      <LABEL index="26" value="17.5" />
      <LABEL index="27" value="18.0" />
      <LABEL index="28" value="18.5" />
      <LABEL index="29" value="19.0" />
      <LABEL index="30" value="19.5" />
      <LABEL index="31" value="20.0" />
      <LABEL index="32" value="20.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2619E" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ms</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x60" flags="0x30">
    <title>DFCO Enable TPS vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle must be below this for decel fuel cut-off to enable. Stock H3 0.15 % (E0187) Effect: decel fuel cut-off behaviour Evidence: ledger:E0187, ledger:E0197, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1358</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F3F8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x61" flags="0x30">
    <title>DFCO Disable TPS vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle above this ends decel fuel cut-off. Stock H3 0.30 % (E0187) Effect: decel fuel cut-off behaviour Evidence: ledger:E0187, ledger:E0197, ledger:E0213, ledger:E0260, ledger:E1358</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F41C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x62" flags="0x30">
    <title>DFCO Enable CylAir vs RPM</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 values]; COUNT is a structure word - never edit it (E0187). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cylinder airmass must be below this for DFCO to enable (two rows, picked by a flag). Stock H3 0.19 -&gt; 0.09 g Effect: decel fuel cut-off behaviour Evidence: ledger:E0187, ledger:E0257, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="1024" />
      <LABEL index="4" value="1536" />
      <LABEL index="5" value="2048" />
      <LABEL index="6" value="2560" />
      <LABEL index="7" value="3072" />
      <LABEL index="8" value="3584" />
      <LABEL index="9" value="4096" />
      <LABEL index="10" value="4608" />
      <LABEL index="11" value="5120" />
      <LABEL index="12" value="5632" />
      <LABEL index="13" value="6144" />
      <LABEL index="14" value="6656" />
      <LABEL index="15" value="7168" />
      <LABEL index="16" value="7680" />
      <LABEL index="17" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="row 0" />
      <LABEL index="1" value="row 1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F43E" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/cyl</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8.191875</max>
      <MATH equation="X/8000"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x63" flags="0x30">
    <title>DFCO Disable CylAir vs RPM</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 values]; COUNT is a structure word - never edit it (E0187). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cylinder airmass above this ends DFCO (two rows, picked by a flag). Stock H3 0.21 -&gt; 0.11 g Effect: decel fuel cut-off behaviour Evidence: ledger:E0187, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="1024" />
      <LABEL index="4" value="1536" />
      <LABEL index="5" value="2048" />
      <LABEL index="6" value="2560" />
      <LABEL index="7" value="3072" />
      <LABEL index="8" value="3584" />
      <LABEL index="9" value="4096" />
      <LABEL index="10" value="4608" />
      <LABEL index="11" value="5120" />
      <LABEL index="12" value="5632" />
      <LABEL index="13" value="6144" />
      <LABEL index="14" value="6656" />
      <LABEL index="15" value="7168" />
      <LABEL index="16" value="7680" />
      <LABEL index="17" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="row 0" />
      <LABEL index="1" value="row 1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F486" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/cyl</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8.191875</max>
      <MATH equation="X/8000"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x64" flags="0x30">
    <title>DFCO Enable Speed vs Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed needed for DFCO to enable, per gear. Stock H3 18.6 mph (1-3) / 49.7 mph (4-6) (E0187) Indexed by transmission state: cells 1st-4th are the gears, 5th/6th unused on the 4L60-E (E0271). Effect: decel fuel cut-off behaviour Evidence: ledger:E0187, ledger:E0211, ledger:E0271</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>gear (in-gear trans state 0..5)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="5th" />
      <LABEL index="5" value="6th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F4D6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x65" flags="0x30">
    <title>DFCO Disable Speed vs Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed below which DFCO ends, per gear. Stock H3 17.4 mph (1-3) / 38.5 mph (4-6) (E0187) Indexed by transmission state: cells 1st-4th are the gears, 5th/6th unused on the 4L60-E (E0271). Effect: decel fuel cut-off behaviour Evidence: ledger:E0187, ledger:E0211, ledger:E0271</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>gear (in-gear trans state 0..5)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="5th" />
      <LABEL index="5" value="6th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F4E2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x66" flags="0x0">
    <title>Minimum ECT to allow DFCO</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum ECT to allow DFCO (E0187) Evidence: ledger:E0187</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2F4EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x67" flags="0x0">
    <title>Maximum ECT to disable DFCO</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Maximum ECT to disable DFCO (E0187) Evidence: ledger:E0187</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2F4F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x68" flags="0x30">
    <title>Cam Phasing Region - RPM Boundaries</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speeds that split the region-based exhaust cam phasing into four rpm bands. Stock 1350 / 1750 / 2150 rpm; the switch happens about 50 rpm past each edge. (Earlier releases described these as fuel-trim cell boundaries; the PCM uses them only for cam phasing regions.) Effect: moves the rpm edges of the cam phasing regions Evidence: ledger:E0744</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>edge</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23072" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x69" flags="0x30">
    <title>Cam Phasing Region - Throttle Boundaries per RPM Band</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle edges that split each rpm band of the region-based exhaust cam phasing into four throttle bands (one row per rpm band). Stock 1.8 / 2.6 / 5.0 % below 1350 rpm up to 1.3 / 5.0 / 8.1 % above 2150 rpm; the switch happens about 0.15 % past each edge. (Earlier releases described these as fuel-trim cell boundaries; the PCM uses them only for cam phasing regions.) Effect: moves the throttle edges of the cam phasing regions Evidence: ledger:E0744</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>edge</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>rpm band</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="below 1350" />
      <LABEL index="1" value="1350-1750" />
      <LABEL index="2" value="1750-2150" />
      <LABEL index="3" value="above 2150" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23078" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6A" flags="0x30">
    <title>Maximum Dwell Time Mult vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier giving the maximum allowed coil dwell, vs rpm. Stock H3 1.35 flat (E0189) Effect: leave stock Evidence: ledger:E0189, ledger:E0210, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1358</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2FA62" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x6B" flags="0x0">
    <title>LTFT Min ECT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel-trim learning allowed above this coolant temp. Stock H3 40 C (E0190) Evidence: ledger:E0190, ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25686" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C" flags="0x0">
    <title>LTFT Max ECT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel-trim learning allowed below this coolant temp. Stock H3 120 C (E0190) Evidence: ledger:E0190, ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25688" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D" flags="0x0">
    <title>Knock Learn Min MAP</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Octane/knock learning only above this MAP. Stock H3 55 kPa (E0191) Evidence: ledger:E0191</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AE98" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6E" flags="0x0">
    <title>Knock Learn Min RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Octane/knock learning only above this rpm. Stock H3 1125 rpm (E0191) Evidence: ledger:E0191</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AE9A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6F" flags="0x0">
    <title>Knock Learn Min Coolant Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learning only above this coolant temp. Stock H3 56 C (E0191) Evidence: ledger:E0191</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AE9C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x70" flags="0x0">
    <title>Knock Learn Min IAT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learning only above this intake air temp. Stock H3 -32.5 C (E0191) Evidence: ledger:E0191</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AE9E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x71" flags="0x0">
    <title>A/C WOT Cut - Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: the cut starts when throttle rises above this, while engine speed is below the cut RPM limit. Stock 100 % (never), and the cut is also turned off by its maximum time of 0. Effect: lower = the cut starts at less throttle Evidence: ledger:E0192, ledger:E0197, ledger:E1009</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x20876" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x72" flags="0x0">
    <title>A/C WOT Cut - Re-Enable Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: the cut is released (after the release hold time) once throttle falls below this. Stock 100 %. Effect: lower = throttle must fall further before the compressor returns Evidence: ledger:E0192, ledger:E0197, ledger:E1009</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x20878" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x73" flags="0x0">
    <title>A/C WOT Cut - RPM Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: the cut only applies while engine speed is below this. Stock 6500 rpm. Effect: lower = the cut only applies at lower rpm Evidence: ledger:E0192, ledger:E1009</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x2087A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x74" flags="0x0">
    <title>A/C WOT Cut - RPM Limit Reset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: once engine speed rises above this the cut no longer applies. Stock 6500 rpm. Effect: raise = the cut keeps applying to a higher rpm Evidence: ledger:E0192, ledger:E1009</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x2087C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x75" flags="0x30">
    <title>Trans Abuse Mode Torque Reduction Duration vs Trans Temp</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE=6][17 points]; COUNT and TYPE are structure bytes - never edit them (E0199). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long each stage of the abuse-mode torque cut is held, vs transmission temperature. The five rows are separate cases: first stage in forward ranges / in reverse, second stage after the first in forward ranges / in reverse, and second stage when the first is not active. Stock 1.0 / 1.0 / 0.6 / 0.6 / 0 s. Effect: abuse protection (e.g. neutral-to-drive at high rpm) Evidence: ledger:E0199, ledger:E0209, ledger:E0988, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="-40" />
      <LABEL index="3" value="-28" />
      <LABEL index="4" value="-16" />
      <LABEL index="5" value="-4" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="20" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="44" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="68" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="92" />
      <LABEL index="14" value="104" />
      <LABEL index="15" value="116" />
      <LABEL index="16" value="128" />
      <LABEL index="17" value="140" />
      <LABEL index="18" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>case</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="first stage, forward ranges" />
      <LABEL index="1" value="first stage, reverse" />
      <LABEL index="2" value="second stage after the first, forward ranges" />
      <LABEL index="3" value="second stage after the first, reverse" />
      <LABEL index="4" value="second stage, first stage not active" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EA92" mmedelementsizebits="8" mmedrowcount="5" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x76" flags="0x30">
    <title>Trans Abuse Mode Torque Reduction vs RPM</title>
    <description>Change in small steps and log. [COUNT=17][TYPE=0][17 points]; COUNT and TYPE are structure bytes - never edit them (E0199). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque cut applied in trans abuse mode, vs rpm. Stock H3 0 % to 1536 rpm, 50 % at 2048, 100 % from 2560 rpm (E0199) Effect: abuse protection Evidence: ledger:E0199, ledger:E0209, ledger:E0257, ledger:E0260, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="512" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1536" />
      <LABEL index="6" value="2048" />
      <LABEL index="7" value="2560" />
      <LABEL index="8" value="3072" />
      <LABEL index="9" value="3584" />
      <LABEL index="10" value="4096" />
      <LABEL index="11" value="4608" />
      <LABEL index="12" value="5120" />
      <LABEL index="13" value="5632" />
      <LABEL index="14" value="6144" />
      <LABEL index="15" value="6656" />
      <LABEL index="16" value="7168" />
      <LABEL index="17" value="7680" />
      <LABEL index="18" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EAF1" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>99.609375</max>
      <MATH equation="X/2.56"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x77" flags="0x0">
    <title>Maximum Line Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper clamp on commanded transmission line pressure. Stock H3 621 kPa (E0200) Effect: line-pressure ceiling - leave stock Evidence: ledger:E0200, ledger:E0241, ledger:E0989</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E230" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x78" flags="0x30">
    <title>Idle Base Spark vs RPM vs Airmass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base spark at idle, vs rpm (400..1600) and cylinder airmass. Stock H3 4..25 deg (E0202) Effect: idle quality / idle torque reserve Evidence: ledger:E0202, ledger:E0210, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1000" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1400" />
      <LABEL index="6" value="1600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EA59" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x79" flags="0x30">
    <title>AC Compressor Torque vs IAT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque model: extra A/C compressor torque by engine speed and intake air temperature (0 below 50 C on stock). It is added to the A/C torque table by head pressure; the sum is the compressor torque counted as an accessory load while the A/C clutch is on. Effect: raise = more engine torque is allowed for the A/C compressor in hot air Evidence: ledger:E0203, ledger:E0210, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1114, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (IAT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-30" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="-10" />
      <LABEL index="3" value="0" />
      <LABEL index="4" value="10" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="40" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="60" />
      <LABEL index="10" value="70" />
      <LABEL index="11" value="80" />
      <LABEL index="12" value="90" />
      <LABEL index="13" value="100" />
      <LABEL index="14" value="110" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="130" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="400" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1200" />
      <LABEL index="4" value="1600" />
      <LABEL index="5" value="2000" />
      <LABEL index="6" value="2400" />
      <LABEL index="7" value="2800" />
      <LABEL index="8" value="3200" />
      <LABEL index="9" value="3600" />
      <LABEL index="10" value="4000" />
      <LABEL index="11" value="4400" />
      <LABEL index="12" value="4800" />
      <LABEL index="13" value="5200" />
      <LABEL index="14" value="5600" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3061E" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>lb-ft</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6042.016932</max>
      <MATH equation="X*0.0921952686597"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7A" flags="0x30">
    <title>Injection Timing (second pulse) - RPM Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. End-of-injection angle term for the second injection pulse by engine speed, in crank degrees of the 720 degree cycle. The coolant term and the engine speed term are added and capped at 720 deg. Stock 0 everywhere. Effect: raise = second injection pulse ends later in the engine cycle Evidence: ledger:E0317, ledger:E1182, ledger:E1329</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm (medium-res engine speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="128" />
      <LABEL index="2" value="256" />
      <LABEL index="3" value="384" />
      <LABEL index="4" value="512" />
      <LABEL index="5" value="640" />
      <LABEL index="6" value="768" />
      <LABEL index="7" value="896" />
      <LABEL index="8" value="1024" />
      <LABEL index="9" value="1152" />
      <LABEL index="10" value="1280" />
      <LABEL index="11" value="1408" />
      <LABEL index="12" value="1536" />
      <LABEL index="13" value="1664" />
      <LABEL index="14" value="1792" />
      <LABEL index="15" value="1920" />
      <LABEL index="16" value="2048" />
      <LABEL index="17" value="2176" />
      <LABEL index="18" value="2304" />
      <LABEL index="19" value="2432" />
      <LABEL index="20" value="2560" />
      <LABEL index="21" value="2688" />
      <LABEL index="22" value="2816" />
      <LABEL index="23" value="2944" />
      <LABEL index="24" value="3072" />
      <LABEL index="25" value="3200" />
      <LABEL index="26" value="3328" />
      <LABEL index="27" value="3456" />
      <LABEL index="28" value="3584" />
      <LABEL index="29" value="3712" />
      <LABEL index="30" value="3840" />
      <LABEL index="31" value="3968" />
      <LABEL index="32" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26152" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg (crank, end of injection)</units>
      <decimalpl>2</decimalpl>
      <min>-1024.000000</min>
      <max>1023.968750</max>
      <MATH equation="X/32"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7B" flags="0x30">
    <title>Cranking VE vs MAP vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Volumetric efficiency used while cranking, vs rpm (0..1280) and MAP (15..105 kPa). Stock H3 59..100 pct (E0206) Effect: cranking fuel - affects hot/cold start Evidence: ledger:E0206, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1329</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="15" />
      <LABEL index="1" value="26" />
      <LABEL index="2" value="38" />
      <LABEL index="3" value="49" />
      <LABEL index="4" value="60" />
      <LABEL index="5" value="71" />
      <LABEL index="6" value="82" />
      <LABEL index="7" value="94" />
      <LABEL index="8" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="40" />
      <LABEL index="2" value="80" />
      <LABEL index="3" value="120" />
      <LABEL index="4" value="160" />
      <LABEL index="5" value="200" />
      <LABEL index="6" value="240" />
      <LABEL index="7" value="280" />
      <LABEL index="8" value="320" />
      <LABEL index="9" value="360" />
      <LABEL index="10" value="400" />
      <LABEL index="11" value="440" />
      <LABEL index="12" value="480" />
      <LABEL index="13" value="520" />
      <LABEL index="14" value="560" />
      <LABEL index="15" value="600" />
      <LABEL index="16" value="640" />
      <LABEL index="17" value="680" />
      <LABEL index="18" value="720" />
      <LABEL index="19" value="760" />
      <LABEL index="20" value="800" />
      <LABEL index="21" value="840" />
      <LABEL index="22" value="880" />
      <LABEL index="23" value="920" />
      <LABEL index="24" value="960" />
      <LABEL index="25" value="1000" />
      <LABEL index="26" value="1040" />
      <LABEL index="27" value="1080" />
      <LABEL index="28" value="1120" />
      <LABEL index="29" value="1160" />
      <LABEL index="30" value="1200" />
      <LABEL index="31" value="1240" />
      <LABEL index="32" value="1280" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AF2C" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7C" flags="0x30">
    <title>Cranking VE Baro Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier on cranking VE vs barometric pressure (60..105 kPa, 10 points). Stock H3 1.64 at 60 kPa -&gt; 1.0 at 100-105 kPa (E0206) Effect: altitude cranking fuel Evidence: ledger:E0206, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1329</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="60" />
      <LABEL index="1" value="65" />
      <LABEL index="2" value="70" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="80" />
      <LABEL index="5" value="85" />
      <LABEL index="6" value="90" />
      <LABEL index="7" value="95" />
      <LABEL index="8" value="100" />
      <LABEL index="9" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B182" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7D" flags="0x30">
    <title>Open Loop Airflow Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier on the open-loop fuel/EQ product (17 x 33 cells). Stock H3 1.00..1.17 (E0207) Effect: open-loop fuelling Evidence: ledger:E0207, ledger:E0213, ledger:E0218, ledger:E0257, ledger:E0260, ledger:E0785, ledger:E1329</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC (modelled temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="20" />
      <LABEL index="1" value="25" />
      <LABEL index="2" value="30" />
      <LABEL index="3" value="35" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="45" />
      <LABEL index="6" value="50" />
      <LABEL index="7" value="55" />
      <LABEL index="8" value="60" />
      <LABEL index="9" value="65" />
      <LABEL index="10" value="70" />
      <LABEL index="11" value="75" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="85" />
      <LABEL index="14" value="90" />
      <LABEL index="15" value="95" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x27E10" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7E" flags="0x30">
    <title>Open Loop Hot-Restart Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra open-loop fuel after a hot restart. A latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, this table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. Columns are coolant temperature; rows are the fuel injected since the engine started, so the extra fuel fades as the engine burns fue...</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="56" />
      <LABEL index="1" value="62" />
      <LABEL index="2" value="68" />
      <LABEL index="3" value="74" />
      <LABEL index="4" value="80" />
      <LABEL index="5" value="86" />
      <LABEL index="6" value="92" />
      <LABEL index="7" value="98" />
      <LABEL index="8" value="104" />
      <LABEL index="9" value="110" />
      <LABEL index="10" value="116" />
      <LABEL index="11" value="122" />
      <LABEL index="12" value="128" />
      <LABEL index="13" value="134" />
      <LABEL index="14" value="140" />
      <LABEL index="15" value="146" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g fuel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="5.5" />
      <LABEL index="2" value="10.9" />
      <LABEL index="3" value="16.4" />
      <LABEL index="4" value="21.9" />
      <LABEL index="5" value="27.4" />
      <LABEL index="6" value="32.8" />
      <LABEL index="7" value="38.3" />
      <LABEL index="8" value="43.8" />
      <LABEL index="9" value="49.3" />
      <LABEL index="10" value="54.7" />
      <LABEL index="11" value="60.2" />
      <LABEL index="12" value="65.7" />
      <LABEL index="13" value="71.2" />
      <LABEL index="14" value="76.6" />
      <LABEL index="15" value="82.1" />
      <LABEL index="16" value="87.6" />
      <LABEL index="17" value="93.1" />
      <LABEL index="18" value="98.5" />
      <LABEL index="19" value="104.0" />
      <LABEL index="20" value="109.5" />
      <LABEL index="21" value="115.0" />
      <LABEL index="22" value="120.4" />
      <LABEL index="23" value="125.9" />
      <LABEL index="24" value="131.4" />
      <LABEL index="25" value="136.9" />
      <LABEL index="26" value="142.3" />
      <LABEL index="27" value="147.8" />
      <LABEL index="28" value="153.3" />
      <LABEL index="29" value="158.8" />
      <LABEL index="30" value="164.2" />
      <LABEL index="31" value="169.7" />
      <LABEL index="32" value="175.2" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x279A8" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7F" flags="0x30">
    <title>Pedal to throttle-area demand - gears 1-3 + Park/Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: which transmission state uses this map is set by the item Pedal Map Select vs Trans State - Normal in this file; the stock selection on this calibration can differ from the H3 described below, so check that table on your own bin before editing this map. Accelerator pedal -&gt; throttle demand for gears 1/2/3 and Park/Neutral: pedal % (columns) x vehicle speed (rows) -&gt; % of the PCM&#x27;s area-&gt;throttle curve input (E0228&#x27;s &#x27;throttle area&#x27;); summed with the idle term and converted to desired throttle by a curve. Effect: pedal response / throttle opening for a given pedal position Evidence:...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x24B76" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x24B9A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23FFE" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x80" flags="0x30">
    <title>Pedal to throttle-area demand - 4th gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: which transmission state uses this map is set by the item Pedal Map Select vs Trans State - Normal in this file; the stock selection on this calibration can differ from the H3 described below, so check that table on your own bin before editing this map. Accelerator pedal -&gt; throttle demand for 4th gear (overdrive): pedal % (columns) x vehicle speed (rows) -&gt; % of the PCM&#x27;s area-&gt;throttle curve input (E0228&#x27;s &#x27;throttle area&#x27;); summed with the idle term and converted to desired throttle by a curve. Effect: pedal response / throttle opening for a given pedal position Evidence: ledger:...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x24B76" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x24B9A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24136" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x81" flags="0x0">
    <title>A/C-on idle target</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Desired idle requested while the A/C compressor is engaged (and held while stopped); wins the max-of-requests, so it only matters when above the coolant-curve target. Stock 675 rpm (reads 672 on PID 11C9) (E0231, E0238) Effect: idle speed with A/C on Evidence: ledger:E0231, ledger:E0238</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A078" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x82" flags="0x0">
    <title>Idle request ramp step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Step per update by which each ramped idle request (A/C and others) moves toward its target; stock 5 rpm (E0231, E0238) Effect: how quickly idle-up requests ramp in/out Evidence: ledger:E0231, ledger:E0238</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A570" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x83" flags="0x30">
    <title>Throttle area -&gt; throttle position model</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converts throttle-area demand to desired throttle position (and back, elsewhere). Shared by ETC and the transmission shift-throttle path. DO NOT TUNE - changing it shifts every pedal, idle and shift-throttle relationship at once (E0228, E0239) Effect: throttle geometry model Evidence: ledger:E0228, ledger:E0239, ledger:E1329, ledger:E1339</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x24D22" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>33</indexcount>
      <units>% throttle area</units>
      <embedinfo type="1" />
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24CDA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x84" flags="0x30">
    <title>Reduced-power (ETC fault) pedal curve</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal -&gt; throttle-area demand used only in ETC reduced-power (fault) mode; stock caps at 8 % area. DO NOT TUNE - fault-mode protection (E0228, E0239) Effect: limp-home throttle Evidence: ledger:E0228, ledger:E0239</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="6.2" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.8" />
      <LABEL index="4" value="25.0" />
      <LABEL index="5" value="31.2" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.8" />
      <LABEL index="8" value="50.0" />
      <LABEL index="9" value="56.2" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.8" />
      <LABEL index="12" value="75.0" />
      <LABEL index="13" value="81.2" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.8" />
      <LABEL index="16" value="100.0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24AF2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle area</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x85" flags="0x30">
    <title>ETC monitor: max expected throttle vs request</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest throttle request the ETC rationality monitor accepts for the current pedal area demand; a request above it for longer than the over-limit time triggers the monitor. DO NOT TUNE - safety diagnostic Effect: throttle rationality monitor Evidence: ledger:E0228, ledger:E0239, ledger:E1124, ledger:E1329</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>% throttle area (request + idle term)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="3.1" />
      <LABEL index="2" value="6.2" />
      <LABEL index="3" value="9.4" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="15.6" />
      <LABEL index="6" value="18.8" />
      <LABEL index="7" value="21.9" />
      <LABEL index="8" value="25.0" />
      <LABEL index="9" value="28.1" />
      <LABEL index="10" value="31.2" />
      <LABEL index="11" value="34.4" />
      <LABEL index="12" value="37.5" />
      <LABEL index="13" value="40.6" />
      <LABEL index="14" value="43.8" />
      <LABEL index="15" value="46.9" />
      <LABEL index="16" value="50.0" />
      <LABEL index="17" value="53.1" />
      <LABEL index="18" value="56.2" />
      <LABEL index="19" value="59.4" />
      <LABEL index="20" value="62.5" />
      <LABEL index="21" value="65.6" />
      <LABEL index="22" value="68.8" />
      <LABEL index="23" value="71.9" />
      <LABEL index="24" value="75.0" />
      <LABEL index="25" value="78.1" />
      <LABEL index="26" value="81.2" />
      <LABEL index="27" value="84.4" />
      <LABEL index="28" value="87.5" />
      <LABEL index="29" value="90.6" />
      <LABEL index="30" value="93.8" />
      <LABEL index="31" value="96.9" />
      <LABEL index="32" value="100.0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24F4E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x86" flags="0x30">
    <title>Pedal Request Factor Authority vs Pedal Demand</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How much of the pedal request factor (the product of the pedal gain reduction, pedal gain increase and the other pedal factors, capped by the Pedal Request Factor Ceiling) is applied to the pedal demand, by pedal demand. 1.0 applies the factor in full, 0 ignores it so the pedal map value passes unchanged, 2.0 doubles its effect. Stock 1.0 everywhere. Range 0 to 2.0. Effect: lower = the pedal gain reduction and increase change the throttle demand less at that pedal demand Evidence: ledger:E0228, ledger:E0239, ledger:E0782, ledger:E1211, ledger:E1212, ledger:E1413</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% throttle area (pedal demand)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="6.2" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.8" />
      <LABEL index="4" value="25.0" />
      <LABEL index="5" value="31.2" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.8" />
      <LABEL index="8" value="50.0" />
      <LABEL index="9" value="56.2" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.8" />
      <LABEL index="12" value="75.0" />
      <LABEL index="13" value="81.2" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.8" />
      <LABEL index="16" value="100.0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23EC8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x87" flags="0x30">
    <title>Pedal to throttle-area demand - Reverse</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: which transmission state uses this map is set by the item Pedal Map Select vs Trans State - Normal in this file; the stock selection on this calibration can differ from the H3 described below, so check that table on your own bin before editing this map. Accelerator pedal -&gt; throttle-area demand for Reverse (normal range). Same layout/axes/scaling as pedal_throttle_area_main. Pointer-table slot k2 (E0240). Effect: pedal response / throttle opening for a given pedal position Evidence: ledger:E0228, ledger:E0232, ledger:E0240, ledger:E0267, ledger:E1327</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x24B76" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x24B9A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2426E" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x88" flags="0x30">
    <title>Pedal to throttle-area demand - 4WD-Low forward gears</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: which transmission state uses this map in 4WD-Low is set by the item Pedal Map Select vs Trans State - 4WD-Low in this file; the stock selection on this calibration can differ from the H3 described below, so check that table on your own bin before editing this map. Accelerator pedal -&gt; throttle-area demand for 4WD-Low, all forward gears. Same layout/axes/scaling as pedal_throttle_area_main. Pointer-table slot k3 (E0240). Effect: pedal response / throttle opening for a given pedal position Evidence: ledger:E0228, ledger:E0232, ledger:E0240, ledger:E0267, ledger:E1327</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x24B76" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x24B9A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x243A6" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x89" flags="0x30">
    <title>Pedal to throttle-area demand - 4WD-Low Park/Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: which transmission state uses this map in 4WD-Low is set by the item Pedal Map Select vs Trans State - 4WD-Low in this file; the stock selection on this calibration can differ from the H3 described below, so check that table on your own bin before editing this map. Accelerator pedal -&gt; throttle-area demand for 4WD-Low, Park/Neutral. Same layout/axes/scaling as pedal_throttle_area_main. Pointer-table slot k4 (E0240). Effect: pedal response / throttle opening for a given pedal position Evidence: ledger:E0228, ledger:E0232, ledger:E0240, ledger:E0267, ledger:E1327</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x24B76" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x24B9A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x244DE" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x8A" flags="0x30">
    <title>Pedal to throttle-area demand - 4WD-Low Reverse</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: which transmission state uses this map in 4WD-Low is set by the item Pedal Map Select vs Trans State - 4WD-Low in this file; the stock selection on this calibration can differ from the H3 described below, so check that table on your own bin before editing this map. Accelerator pedal -&gt; throttle-area demand for 4WD-Low, Reverse. Same layout/axes/scaling as pedal_throttle_area_main. Pointer-table slot k5 (E0240). Effect: pedal response / throttle opening for a given pedal position Evidence: ledger:E0228, ledger:E0232, ledger:E0240, ledger:E0267, ledger:E1327</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x24B76" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x24B9A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24616" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x8B" flags="0x30">
    <title>Pedal to Throttle-Area Demand - Slot k6 (mode 2, forward gears and Park / Neutral)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: which transmission state uses this map is set by a pedal mode 2 selector that is not in this file; the stock selection on this calibration can differ from the H3 described below. Pedal map (pedal % by vehicle speed to throttle-area demand) in slot k6, used for forward gears and Park / Neutral while pedal mode 2 is selected. Pedal mode 2 is selected while byte 0 of a message the PCM receives on the vehicle bus carries state 1 or 2; state 3 of the same byte selects the 4WD-Low maps. The sending module is believed to be the transfer case; that is not confirmed. Stock values are the same as the 4WD-Low forward map...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x24B76" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x24B9A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2474E" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x8C" flags="0x30">
    <title>Pedal to Throttle-Area Demand - Slot k8 (mode 2, Reverse)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: which transmission state uses this map is set by a pedal mode 2 selector that is not in this file; the stock selection on this calibration can differ from the H3 described below. Pedal map (pedal % by vehicle speed to throttle-area demand) in slot k8, used for Reverse while pedal mode 2 is selected. Pedal mode 2 is selected while byte 0 of a message the PCM receives on the vehicle bus carries state 1 or 2; state 3 of the same byte selects the 4WD-Low maps. The sending module is believed to be the transfer case; that is not confirmed. Stock values are the same as the 4WD-Low Reverse map. Same layout, axes and s...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x24B76" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x24B9A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x249BE" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x8D" flags="0x0">
    <title>Final Drive Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Axle ratio used to compute vehicle speed from the output-shaft sensor. Stock H3 4.56. Change it together with tire revs when the axle gearing changes. Live 2026-09-23: the PCM&#x27;s own vehicle speed matches this pair within 1.0 %. The PCM computes speed from output-shaft speed using these same constants, so that confirms the decode, not your actual tire size or axle ratio. Check a new setting against GPS. Shift points and converter lockup do not use this value: the transmission computes its own speed from a separate axle ratio and tire size. Those two are traced but not yet released, so after a tire or gear change the shift...</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x2008C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>:1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8E" flags="0x0">
    <title>VSS Tire Revs per Distance</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tire revolutions per mile (stored as revs/km x32). Stock H3 627.6/mi (~32.1 in tire). Lower it for taller tires to correct the speedometer. Live 2026-09-23: the PCM&#x27;s own vehicle speed matches this pair within 1.0 %. The PCM computes speed from output-shaft speed using these same constants, so that confirms the decode, not your actual tire size or axle ratio. Check a new setting against GPS. Shift points and converter lockup do not use this value: the transmission computes its own speed from a separate axle ratio and tire size. Those two are traced but not yet released, so after a tire or gear change the shift points sti...</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x2008E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>revs/mi</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3295.886220</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*0.05029200"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x8F" flags="0x30">
    <title>Torque loss vs spark retard from MBT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of gross torque lost when final spark is below the torque-model MBT spark. Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0280, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>deg retard</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="3" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="9" />
      <LABEL index="4" value="12" />
      <LABEL index="5" value="15" />
      <LABEL index="6" value="18" />
      <LABEL index="7" value="21" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="27" />
      <LABEL index="10" value="30" />
      <LABEL index="11" value="33" />
      <LABEL index="12" value="36" />
      <LABEL index="13" value="39" />
      <LABEL index="14" value="42" />
      <LABEL index="15" value="45" />
      <LABEL index="16" value="48" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30B1A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% torque lost</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x90" flags="0x30">
    <title>Torque model MBT spark vs airmass vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Optimal (MBT) spark the torque model compares final spark against; used only for the spark-loss term. Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0280, ledger:E1314</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g airmass</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.20" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.40" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.60" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.80" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1.00" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.20" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30B55" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x91" flags="0x30">
    <title>Torque model MBT spark adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the torque-model MBT spark; by cam-phase factor (0 to 0.24 in 0.03 steps); stock all 0. Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0255, ledger:E0280, ledger:E0896, ledger:E1577</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>cam-phase factor</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.03" />
      <LABEL index="2" value="0.06" />
      <LABEL index="3" value="0.09" />
      <LABEL index="4" value="0.12" />
      <LABEL index="5" value="0.15" />
      <LABEL index="6" value="0.18" />
      <LABEL index="7" value="0.21" />
      <LABEL index="8" value="0.24" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30B3E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x92" flags="0x30">
    <title>Engine friction vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Friction torque vs rpm (enters the loss sum at half weight; the math includes that). Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0280, ledger:E0936, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30886" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x93" flags="0x30">
    <title>Coolant-dependent friction vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Friction torque vs rpm at the warm multiplier (x torque_friction_coolant_mult). Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0280, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30862" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x94" flags="0x30">
    <title>Friction multiplier vs coolant vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier on the coolant-dependent friction; stock 2.4 when coldest to 1.0 warm. Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0254, ledger:E0280, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (corrected coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="50" />
      <LABEL index="4" value="80" />
      <LABEL index="5" value="110" />
      <LABEL index="6" value="140" />
      <LABEL index="7" value="170" />
      <LABEL index="8" value="200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x308AE" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>3.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x95" flags="0x30">
    <title>Load-dependent torque loss vs airmass vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Loss torque vs airmass and rpm, added to friction. Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0280, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>g airmass</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.40" />
      <LABEL index="2" value="0.72" />
      <LABEL index="3" value="1.04" />
      <LABEL index="4" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30D8E" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x96" flags="0x0">
    <title>Engine inertia torque factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales filtered engine acceleration into the inertia torque the PCM subtracts from its engine torque estimate. Part of the torque model, which reproduces logged delivered torque at steady load within about 6 %. Shift pressure, torque reduction, converter clutch and throttle torque control all use that estimate. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (torque model) Evidence: ledger:E0246, ledger:E0280, ledger:E0899</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x303CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x97" flags="0x0">
    <title>Line pressure boost gain (normal)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Line pressure = force-motor pressure x this + offset (normal ranges); stock 1.333. Hydraulic constant - DO NOT TUNE (E0247) Effect: converts between commanded line pressure and force-motor pressure Evidence: ledger:E0247</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C5F8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x98" flags="0x0">
    <title>Line pressure boost offset (normal)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Line pressure at zero force-motor pressure (normal ranges); stock 414 kPa = 60 psi. Hydraulic constant - DO NOT TUNE (E0247) Effect: converts between commanded line pressure and force-motor pressure Evidence: ledger:E0247</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C5FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x99" flags="0x0">
    <title>Line pressure boost gain (mode 6, likely Reverse)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. As the normal line pressure boost gain, used when the transmission range code is 6 (likely Reverse). Stock 2.0. DO NOT TUNE. Effect: converts between commanded line pressure and force-motor pressure Evidence: ledger:E0247</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C5FA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9A" flags="0x0">
    <title>Line pressure boost offset (mode 6, likely Reverse)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. As the normal line pressure boost offset, used when the transmission range code is 6 (likely Reverse). Stock 621 kPa = 90 psi. DO NOT TUNE. Effect: converts between commanded line pressure and force-motor pressure Evidence: ledger:E0247</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C5FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x9B" flags="0x30">
    <title>Line Pressure - Input Torque Gain by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Line pressure added per Nm of transmission input torque, by gear and whether the converter clutch is on, in the normal line pressure mode. The base offset is added on top. Stock 3.00 kPa per Nm in 1st and 2nd, 3.25 from 3rd and in reverse. Line pressure protects the clutches: change in small steps. Effect: raise = more line pressure for the same input torque Evidence: ledger:E0247, ledger:E0250, ledger:E1029</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>gear / converter clutch</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="1st, TCC on" />
      <LABEL index="2" value="2nd" />
      <LABEL index="3" value="2nd, TCC on" />
      <LABEL index="4" value="3rd" />
      <LABEL index="5" value="3rd, TCC on" />
      <LABEL index="6" value="4th" />
      <LABEL index="7" value="4th, TCC on" />
      <LABEL index="8" value="Reverse" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C6C8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa per Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9C" flags="0x30">
    <title>Line Pressure - Input Torque Gain by Gear, Top Gear Light Load</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Line pressure added per Nm of transmission input torque, used instead of the normal gain when engine torque is below a small threshold (up to about 46 Nm stock) and either the transmission is already in the highest gear the selected range allows (or is held in gear by the cruise rule), or the PCM has substituted its default range for the range selector input. Stock 4.01 kPa per Nm in the 1st and 2nd slots, 1.66 in 3rd, 3.21 with the converter clutch on, 2.70 in 4th, 3.11 in reverse. Effect: raise = more line pressure at light load in the top gear of the range Evidence: ledger:E0247, ledger:E0250, ledger:E1029, ledger:E1030, l...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>gear / converter clutch</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="1st, TCC on" />
      <LABEL index="2" value="2nd" />
      <LABEL index="3" value="2nd, TCC on" />
      <LABEL index="4" value="3rd" />
      <LABEL index="5" value="3rd, TCC on" />
      <LABEL index="6" value="4th" />
      <LABEL index="7" value="4th, TCC on" />
      <LABEL index="8" value="Reverse" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C6DA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa per Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9D" flags="0x30">
    <title>Line pressure torque-term multiplier vs trans temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier on the torque part of line pressure vs trans temperature; stock 1.25 cold, 1.0 normal, 1.29 hot (E0247) Effect: line pressure temperature compensation Evidence: ledger:E0247</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (trans temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C6A4" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x9E" flags="0x0">
    <title>COT enrichment entry rpm</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst over-temp enrichment arms above this rpm (with load and coolant). Stock 3200. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D26" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9F" flags="0x0">
    <title>COT enrichment hold rpm</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. COT enrichment stays armed above this rpm. Stock 3000. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D28" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA0" flags="0x0">
    <title>COT enrichment minimum coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. COT enrichment arms only above this coolant temperature. Stock 85 C. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D2A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA1" flags="0x0">
    <title>COT enrichment delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the COT conditions must hold before enrichment starts. Stock 15 s. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D2E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xA2" flags="0x30">
    <title>COT enrichment EQ cap vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Maximum commanded EQ during catalyst over-temp enrichment. Stock 1.18..1.40. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249, ledger:E1329</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26DA6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA3" flags="0x30">
    <title>COT enrichment ramp-in step vs coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EQ added per update while COT enrichment ramps in. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249, ledger:E1329</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26D5A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ per update</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA4" flags="0x30">
    <title>COT enrichment ramp-out step vs coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EQ removed per update after COT conditions end. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249, ledger:E1329</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26D7E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ per update</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xA5" flags="0x0">
    <title>Over-temp enrichment start coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine over-temp enrichment adds EQ above this coolant temperature. Stock 110 C. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D20" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA6" flags="0x0">
    <title>Over-temp enrichment gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EQ added per degree above the start temperature. Stock 0.05. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D22" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ per degC</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA7" flags="0x0">
    <title>Over-temp enrichment EQ cap</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Maximum commanded EQ from over-temp enrichment. Stock 2.0. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D24" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA8" flags="0x0">
    <title>Over-temp enrichment delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the over-temp conditions must hold before enrichment. Stock 2 s. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D2C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xA9" flags="0x30">
    <title>Line Pressure - Base Offset by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Line pressure at zero input torque, by gear and whether the converter clutch is on, in the normal line pressure mode. The torque gain term is added on top. Stock 175 kPa (25 psi) in the forward gears, 207 kPa (30 psi) in reverse. Line pressure protects the clutches: change in small steps. Effect: raise = more line pressure at every torque Evidence: ledger:E0247, ledger:E0250, ledger:E1029</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>gear / converter clutch</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="1st, TCC on" />
      <LABEL index="2" value="2nd" />
      <LABEL index="3" value="2nd, TCC on" />
      <LABEL index="4" value="3rd" />
      <LABEL index="5" value="3rd, TCC on" />
      <LABEL index="6" value="4th" />
      <LABEL index="7" value="4th, TCC on" />
      <LABEL index="8" value="Reverse" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C6EC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAA" flags="0x30">
    <title>Line Pressure Base Offset (Alternate)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Used instead of the Top Gear Line Pressure Offset table when Top Gear Line Pressure - Use Alternate Base Offset is 1: the line pressure offset in top gear with light torque and the minimum line pressure in top gear with heavy torque, by gear and converter clutch state. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (base line pressure in top gear if the switch is set) Evidence: ledger:E0247, ledger:E0250, ledger:E1029, ledger:E1394</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>gear / converter clutch</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="1st, TCC on" />
      <LABEL index="2" value="2nd" />
      <LABEL index="3" value="2nd, TCC on" />
      <LABEL index="4" value="3rd" />
      <LABEL index="5" value="3rd, TCC on" />
      <LABEL index="6" value="4th" />
      <LABEL index="7" value="4th, TCC on" />
      <LABEL index="8" value="Reverse" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C6FE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAB" flags="0x30">
    <title>TAP maximum learned pressure (1-2/2-3/3-4)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper clamp on the learned shift-pressure correction per shift and torque cell. Stock 0 -&gt; 20 psi (1-2, 2-3), 0 for 3-4. Raising it lets TAP add more pressure (E0251) Effect: bounds / rate of adaptive shift pressure learning Evidence: ledger:E0235, ledger:E0251, ledger:E0708</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3BFE8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>Nm (shift torque)</units>
      <embedinfo type="1" />
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C3C6" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>psi</units>
      <decimalpl>3</decimalpl>
      <min>-297.032090</min>
      <max>297.023025</max>
      <MATH equation="X*0.0090647"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAC" flags="0x30">
    <title>TAP minimum learned pressure (1-2/2-3/3-4)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower clamp on the learned shift-pressure correction. Stock 0 -&gt; -5.8..-7.3 psi (E0251) Effect: bounds / rate of adaptive shift pressure learning Evidence: ledger:E0235, ledger:E0251, ledger:E0708</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3BFE8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>Nm (shift torque)</units>
      <embedinfo type="1" />
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C42E" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>psi</units>
      <decimalpl>3</decimalpl>
      <min>-297.032090</min>
      <max>297.023025</max>
      <MATH equation="X*0.0090647"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAD" flags="0x30">
    <title>Shift Adapt - Pressure Step vs Shift Time Error</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Step added to the learned shift pressure after a shift, by how far the shift time was from the desired time, for the 1-2, 2-3 and 3-4 shifts. Positive when the shift was slower than desired. The step is multiplied by the adapt step gain (stock zero below 240 Nm of shift torque, so nothing is learned there) and spread over the neighbouring torque cells. Stock up to 16 kPa (2.3 psi) for a shift 0.2 s slow; the 3-4 row is zero. Effect: raise = the adaption corrects shift pressure in bigger steps Evidence: ledger:E0235, ledger:E0251,...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>MARKER/MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="MARKER" />
      <LABEL index="2" value="-0.200" />
      <LABEL index="3" value="-0.175" />
      <LABEL index="4" value="-0.150" />
      <LABEL index="5" value="-0.125" />
      <LABEL index="6" value="-0.100" />
      <LABEL index="7" value="-0.075" />
      <LABEL index="8" value="-0.050" />
      <LABEL index="9" value="-0.025" />
      <LABEL index="10" value="0.000" />
      <LABEL index="11" value="0.025" />
      <LABEL index="12" value="0.050" />
      <LABEL index="13" value="0.075" />
      <LABEL index="14" value="0.100" />
      <LABEL index="15" value="0.125" />
      <LABEL index="16" value="0.150" />
      <LABEL index="17" value="0.175" />
      <LABEL index="18" value="0.200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C38A" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>-256.000000</min>
      <max>254.000000</max>
      <MATH equation="X*2"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xAE" flags="0x0">
    <title>TAP learning minimum trans temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Adaptive shift pressure learns only above this trans temperature. Stock 60 C. (E0251) Effect: when TAP learns Evidence: ledger:E0235, ledger:E0251</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C522" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAF" flags="0x0">
    <title>TAP learning maximum trans temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Adaptive shift pressure learns only below this trans temperature. Stock 110 C. (E0251) Effect: when TAP learns Evidence: ledger:E0235, ledger:E0251</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C520" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB0" flags="0x0">
    <title>MAF-fault mode 2: VE cap factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In MAF-fault mode 2 the fuel airmass is min(MAF, VE x this). Stock 0.995. Fault handling - DO NOT TUNE (E0219, E0253) Effect: MAF / VE airflow arbitration Evidence: ledger:E0219, ledger:E0253</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2AF26" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB1" flags="0x0">
    <title>MAF-fault mode 2: filter coefficient</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter on the mode-2 capped airmass. Stock 0.110. Fault handling - DO NOT TUNE (E0219, E0253) Effect: MAF / VE airflow arbitration Evidence: ledger:E0219, ledger:E0253</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2AF24" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB2" flags="0x0">
    <title>Steady-state fuel airmass filter toward MAF</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the steady-state fuel airmass follows MAF airmass. Stock 0.150. (E0219, E0253) Effect: MAF / VE airflow arbitration Evidence: ledger:E0219, ledger:E0253</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2B1EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB3" flags="0x0">
    <title>Learned MAF/VE ratio filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the learned MAF/VE ratio adapts in steady state. Stock 0.018. (E0219, E0253) Effect: MAF / VE airflow arbitration Evidence: ledger:E0219, ledger:E0253</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2B1EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB4" flags="0x0">
    <title>Learned MAF/VE ratio maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper clamp on the learned MAF/VE ratio. Stock 1.5. (E0219, E0253) Effect: MAF / VE airflow arbitration Evidence: ledger:E0219, ledger:E0253</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2B1F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB5" flags="0x0">
    <title>Learned MAF/VE ratio minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower clamp on the learned MAF/VE ratio. Stock 0.5. (E0219, E0253) Effect: MAF / VE airflow arbitration Evidence: ledger:E0219, ledger:E0253</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2B1F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB6" flags="0x0">
    <title>Learned MAF/VE Ratio - Reset Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM learns a MAF to VE airflow ratio in steady state and uses it on the VE airflow during transients. While manifold pressure is below the deep vacuum MAP (closed throttle decel) learning is frozen; on the first update back above it, a learned ratio below the reset threshold is put back to 1.0, and a higher one is kept. This is the reset threshold: a learned ratio below it is reset to 1.0 after each deep vacuum episode. Stock 1.05. Effect: raise = more learned ratios are thrown away after decel; 0 = never reset Evidence: ledger:E0219, ledger:E0253, ledger:E0856</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2B1F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB7" flags="0x30">
    <title>Cam-Phase Factor vs Cam Angle and RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A 0 to 1 factor by actual cam angle and engine speed that multiplies a spark correction and sets the input of a dwell correction. Stock 0 up to 7.5 degrees of cam, rising to 0.24 at 24 degrees; on the stock truck the cam reaches 9 to 11 degrees under load, so this is active. Effect: raise = more of the cam-phase spark correction at that cam angle and speed Evidence: ledger:E0255, ledger:E0782, ledger:E0881, ledger:E1413</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="800" />
      <LABEL index="1" value="1400" />
      <LABEL index="2" value="2000" />
      <LABEL index="3" value="2600" />
      <LABEL index="4" value="3200" />
      <LABEL index="5" value="3800" />
      <LABEL index="6" value="4400" />
      <LABEL index="7" value="5000" />
      <LABEL index="8" value="5600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>deg cam</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1.5" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4.5" />
      <LABEL index="4" value="6" />
      <LABEL index="5" value="7.5" />
      <LABEL index="6" value="9" />
      <LABEL index="7" value="10.5" />
      <LABEL index="8" value="12" />
      <LABEL index="9" value="13.5" />
      <LABEL index="10" value="15" />
      <LABEL index="11" value="16.5" />
      <LABEL index="12" value="18" />
      <LABEL index="13" value="19.5" />
      <LABEL index="14" value="21" />
      <LABEL index="15" value="22.5" />
      <LABEL index="16" value="24" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22DA6" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB8" flags="0x0">
    <title>Traction Control - Cold Engine Coolant Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control: at or below this coolant temperature the engine reports torque control as not available to the other modules. On this calibration the torque reduction through the throttle still acts when it is requested. Stock -40 C. Effect: raise = torque control is reported as not available up to a warmer engine Evidence: ledger:E0256, ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30320" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB9" flags="0x0">
    <title>Traction Control Fuel Cut Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lets a traction control request cut fuel. 1: when the brake / traction module asks for less torque and traction control is active, the PCM may cut fuel, unless Traction Control Fuel Cut Inhibit is set. 0 (stock): traction control never cuts fuel; it still reduces torque through the throttle. Has no effect without a traction control module on the bus. Effect: 1 = traction control may cut fuel (needs inhibit 0); 0 = stock Evidence: ledger:E0256, ledger:E1744</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30372" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = allowed, 0 = off (stock)</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBA" flags="0x0">
    <title>Traction Control Fuel Cut Inhibit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Blocks traction control fuel cut. 1 (stock): traction control never cuts fuel, whatever the enable says. 0: fuel cut follows Traction Control Fuel Cut Enable. Has no effect without a traction control module on the bus. Effect: 0 = fuel cut follows the enable; 1 = stock (blocked) Evidence: ledger:E0256, ledger:E1744</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x208BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = blocked (stock), 0 = not blocked</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xBB" flags="0x30">
    <title>ETC torque request baro multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the indicated torque request before the ETC torque-to-throttle table. Stock 1.35 at 65 kPa down to 0.95 at 105 kPa (E0259) Effect: increase = more throttle for the same torque request Evidence: ledger:E0259, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="65" />
      <LABEL index="1" value="75" />
      <LABEL index="2" value="85" />
      <LABEL index="3" value="95" />
      <LABEL index="4" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30E5E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBC" flags="0x30">
    <title>ETC torque request IAT multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the indicated torque request before the ETC torque-to-throttle table. Stock 0.89 cold, 1.00 at 45-79 C, 1.19 at 140 C (E0259) Effect: increase = more throttle for the same torque request Evidence: ledger:E0259, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (IAT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28.75" />
      <LABEL index="2" value="-17.5" />
      <LABEL index="3" value="-6.25" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="16.25" />
      <LABEL index="6" value="27.5" />
      <LABEL index="7" value="38.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="61.25" />
      <LABEL index="10" value="72.5" />
      <LABEL index="11" value="83.75" />
      <LABEL index="12" value="95" />
      <LABEL index="13" value="106.25" />
      <LABEL index="14" value="117.5" />
      <LABEL index="15" value="128.75" />
      <LABEL index="16" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30E6A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBD" flags="0x30">
    <title>O2 switch-point adder A phase-in delay vs startup coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Run time after start before O2 switch-point adder A (from O2 error via a curve) begins to phase in. Stock 200 s cold, 30 s hot. The adder biases the closed-loop rich/lean switch point. The oxygen sensor input here is the rear (post catalyst) sensor, bank 1 sensor 2. Effect: raise = closed-loop O2 correction arrives later / more gradually after a start Evidence: ledger:E0273, ledger:E0281, ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant at start)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28.75" />
      <LABEL index="2" value="-17.5" />
      <LABEL index="3" value="-6.25" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="16.25" />
      <LABEL index="6" value="27.5" />
      <LABEL index="7" value="38.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="61.25" />
      <LABEL index="10" value="72.5" />
      <LABEL index="11" value="83.75" />
      <LABEL index="12" value="95" />
      <LABEL index="13" value="106.25" />
      <LABEL index="14" value="117.5" />
      <LABEL index="15" value="128.75" />
      <LABEL index="16" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x257D8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBE" flags="0x30">
    <title>O2 switch-point adder A phase-in ramp time vs startup coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time over which O2 feedback term A ramps from 0 to full once its delay has passed. Stock 120 s cold, 30 s hot. The adder biases the closed-loop rich/lean switch point (E0281). The oxygen sensor input here is the rear (post catalyst) sensor, bank 1 sensor 2. Effect: raise = closed-loop O2 correction arrives later / more gradually after a start Evidence: ledger:E0273, ledger:E0281, ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant at start)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28.75" />
      <LABEL index="2" value="-17.5" />
      <LABEL index="3" value="-6.25" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="16.25" />
      <LABEL index="6" value="27.5" />
      <LABEL index="7" value="38.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="61.25" />
      <LABEL index="10" value="72.5" />
      <LABEL index="11" value="83.75" />
      <LABEL index="12" value="95" />
      <LABEL index="13" value="106.25" />
      <LABEL index="14" value="117.5" />
      <LABEL index="15" value="128.75" />
      <LABEL index="16" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25820" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBF" flags="0x30">
    <title>O2 switch-point adder B phase-in delay vs startup coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Run time after start before O2 switch-point adder B (from filtered O2 via a curve) begins to phase in. Stock 200 s cold, 30 s hot. The adder biases the closed-loop rich/lean switch point. The oxygen sensor input here is the rear (post catalyst) sensor, bank 1 sensor 2. Effect: raise = closed-loop O2 correction arrives later / more gradually after a start Evidence: ledger:E0273, ledger:E0281, ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant at start)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28.75" />
      <LABEL index="2" value="-17.5" />
      <LABEL index="3" value="-6.25" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="16.25" />
      <LABEL index="6" value="27.5" />
      <LABEL index="7" value="38.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="61.25" />
      <LABEL index="10" value="72.5" />
      <LABEL index="11" value="83.75" />
      <LABEL index="12" value="95" />
      <LABEL index="13" value="106.25" />
      <LABEL index="14" value="117.5" />
      <LABEL index="15" value="128.75" />
      <LABEL index="16" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x257FC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC0" flags="0x30">
    <title>O2 switch-point adder B phase-in ramp time vs startup coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time over which O2 feedback term B ramps from 0 to full once its delay has passed. Stock 120 s cold, 5 s hot. The adder biases the closed-loop rich/lean switch point (E0281). The oxygen sensor input here is the rear (post catalyst) sensor, bank 1 sensor 2. Effect: raise = closed-loop O2 correction arrives later / more gradually after a start Evidence: ledger:E0273, ledger:E0281, ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant at start)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28.75" />
      <LABEL index="2" value="-17.5" />
      <LABEL index="3" value="-6.25" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="16.25" />
      <LABEL index="6" value="27.5" />
      <LABEL index="7" value="38.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="61.25" />
      <LABEL index="10" value="72.5" />
      <LABEL index="11" value="83.75" />
      <LABEL index="12" value="95" />
      <LABEL index="13" value="106.25" />
      <LABEL index="14" value="117.5" />
      <LABEL index="15" value="128.75" />
      <LABEL index="16" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25844" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC1" flags="0x30">
    <title>Catalyst Light-off Spark Retard - Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark retard subtracted from idle base spark for about two minutes after a cold start, to heat the catalytic converters. Scaled by the run-time and coolant factor curves. Columns 400..1600 rpm, but 1600 is never reached (the input clamps below it). Stock up to 12 deg. Effect: raise = more spark retard during the post-start catalyst warm-up (hotter exhaust, less torque) Evidence: ledger:E0275, ledger:E0276</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1000" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1400" />
      <LABEL index="6" value="1600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E409" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>deg retard</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>63.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC2" flags="0x30">
    <title>Catalyst Light-off Spark Retard - Idle (alternate) - NOT USED on this calibration</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Alternate idle light-off retard table, selected only when a calibration switch is 0. Not used on this calibration. Effect: none on this calibration Evidence: ledger:E0275, ledger:E0276</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1000" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1400" />
      <LABEL index="6" value="1600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E4F9" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>deg retard</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>63.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC3" flags="0x30">
    <title>Catalyst Light-off Spark Retard - Off-Idle (main spark)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Light-off retard subtracted from main spark in spark mode 5 (off idle), also scaled by a light-throttle curve (full at low throttle). Stock up to 15 deg. Effect: raise = more spark retard during the post-start catalyst warm-up (hotter exhaust, less torque) Evidence: ledger:E0275, ledger:E0276</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E5E9" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>deg retard</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>63.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC4" flags="0x30">
    <title>Catalyst Light-off Spark Retard - Coastdown</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Light-off retard subtracted from idle coastdown spark (spark mode 3). Stock up to 8 deg. Effect: raise = more spark retard during the post-start catalyst warm-up (hotter exhaust, less torque) Evidence: ledger:E0275, ledger:E0276</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E821" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>deg retard</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>63.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC5" flags="0x30">
    <title>Catalyst Light-off Retard vs Time Since Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of the light-off retard applied vs engine run time (255 = full). Stock: full from 5 to 110 s, half at 115 s, off from 120 s. Effect: raise or extend = retard lasts longer after start Evidence: ledger:E0275, ledger:E0276, ledger:E0277</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>s since start</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <LABEL index="21" value="105" />
      <LABEL index="22" value="110" />
      <LABEL index="23" value="115" />
      <LABEL index="24" value="120" />
      <LABEL index="25" value="125" />
      <LABEL index="26" value="130" />
      <LABEL index="27" value="135" />
      <LABEL index="28" value="140" />
      <LABEL index="29" value="145" />
      <LABEL index="30" value="150" />
      <LABEL index="31" value="155" />
      <LABEL index="32" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E3DF" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>0.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC6" flags="0x30">
    <title>Catalyst Light-off Retard vs Coolant (A)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First coolant factor on the light-off retard (multiplied with factor B). Stock full 10..50 C, off at 80 C. Effect: raise = light-off retard applies at more coolant temperatures Evidence: ledger:E0275, ledger:E0276, ledger:E0277</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E3B9" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>0.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC7" flags="0x30">
    <title>Catalyst Light-off Retard vs Coolant (B)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Second coolant factor on the light-off retard. Stock full 10..30 C, half at 40 C, off from 50 C - on stock this is the one that ends the retard as the engine warms. Effect: raise = light-off retard applies at more coolant temperatures Evidence: ledger:E0275, ledger:E0276, ledger:E0277</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E3CC" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>0.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC8" flags="0x30">
    <title>IAT Spark Correction - Coolant Scaler</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the IAT spark correction (IAT add x IAT multiplier) by a factor of coolant temperature. Stock 0 up to 60 C, 1.0 at 80-100 C, 0.5 at 120 C, so the IAT correction only acts on a warm engine. Effect: raise = IAT spark correction applies at more coolant temperatures Evidence: ledger:E0277</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E394" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC9" flags="0x30">
    <title>Cranking Fuel Multiplier vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the cranking fuel amount by engine speed (0 to 1600 rpm). Stock 1.0 up to 300 rpm, 0.95 / 0.80 / 0.70 / 0.60 at 400 to 700 rpm and 0.5 from 800 rpm. It acts only on cranking fuel and on the crank-to-run blend that starts from it; running fuel does not use it, so it does not lean out a low idle. Effect: raise = more cranking fuel at that engine speed Evidence: ledger:E0277, ledger:E1090</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="100" />
      <LABEL index="2" value="200" />
      <LABEL index="3" value="300" />
      <LABEL index="4" value="400" />
      <LABEL index="5" value="500" />
      <LABEL index="6" value="600" />
      <LABEL index="7" value="700" />
      <LABEL index="8" value="800" />
      <LABEL index="9" value="900" />
      <LABEL index="10" value="1000" />
      <LABEL index="11" value="1100" />
      <LABEL index="12" value="1200" />
      <LABEL index="13" value="1300" />
      <LABEL index="14" value="1400" />
      <LABEL index="15" value="1500" />
      <LABEL index="16" value="1600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x255B8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xCA" flags="0x30">
    <title>TAP Adapt Gain vs Shift Torque</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the adaptive shift-pressure (TAP) learning step by shift torque, per shift (rows 1-2, 2-3, 3-4). Stock 0 below 240 Nm and 1.0 above, so the PCM does not learn shift pressure on light-torque shifts. Effect: raise at low torque = TAP learns on lighter shifts too Evidence: ledger:E0277</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>MARKER/MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="MARKER" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="2" />
      <LABEL index="4" value="3" />
      <LABEL index="5" value="4" />
      <LABEL index="6" value="5" />
      <LABEL index="7" value="6" />
      <LABEL index="8" value="7" />
      <LABEL index="9" value="8" />
      <LABEL index="10" value="9" />
      <LABEL index="11" value="10" />
      <LABEL index="12" value="11" />
      <LABEL index="13" value="12" />
      <LABEL index="14" value="13" />
      <LABEL index="15" value="14" />
      <LABEL index="16" value="15" />
      <LABEL index="17" value="16" />
      <LABEL index="18" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C582" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xCB" flags="0x30">
    <title>Catalyst Light-off Retard vs Throttle (off-idle)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of the off-idle light-off retard applied vs relative throttle. Stock full up to 20 %, 1/3 at 40 %, off from 50 %, so light-off retard gives way when you press the pedal. Effect: raise = light-off retard continues at more throttle Evidence: ledger:E0277</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>% throttle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E3AC" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>0.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xCC" flags="0x0">
    <title>MAP Sensor Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Span of the MAP sensor: the pressure range the PCM reads between 0 V and 5 V (stock 94.1 kPa, so with the offset 10.4 to 104.5 kPa, a stock 1-bar sensor). MAP = offset + this x sensor volts / 5. Change it together with the offset and the filtered-path span when fitting a different MAP sensor. With a boost MAP sensor: the PCM&#x27;s barometric pressure estimate takes the MAP reading whenever MAP is higher than the current estimate, capped at 110 kPa. After the first boost the barometric pressure therefore reads 110 kPa (about 9 kPa high at sea level) until a full-throttle reading below barometric pressure or the next key-on co...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C5FA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa across 0 to 5 V</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCD" flags="0x0">
    <title>MAP Sensor Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intercept of the MAP sensor conversion (kPa at 0 counts, added unsigned so it cannot go below 0). Stock 10.40 kPa. Shared by all three MAP conversion paths. With a boost MAP sensor: the PCM&#x27;s barometric pressure estimate takes the MAP reading whenever MAP is higher than the current estimate, capped at 110 kPa. After the first boost the barometric pressure therefore reads 110 kPa (about 9 kPa high at sea level) until a full-throttle reading below barometric pressure or the next key-on corrects it; the cap is fixed in the operating system. The MAP circuit high / low codes test the raw sensor signal, not the converted press...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C5FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa at 0 V</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCE" flags="0x0">
    <title>MAP Sensor Gain (filtered path)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Span used for the filtered MAP path. Keep it equal to MAP Sensor Gain as displayed (it is stored as half because that path runs at twice the scale). Stock 94.1 kPa across 0 to 5 V. Effect: keep equal to MAP Sensor Gain Evidence: ledger:E0278, ledger:E1462</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C5FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa across 0 to 5 V</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xCF" flags="0x30">
    <title>O2 Switch Point - Base (per bank)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base O2 voltage above which closed loop calls the mixture rich, per bank. Stock 530 mV at the low end of its input falling to 340 mV. Lowering it makes closed loop run leaner, raising it richer. Column positions are set by the O2 Switch Point Airflow Map: stock 0 to 76 g/s, most columns below 30 g/s (E0290). Effect: raise = closed-loop fuelling runs richer Evidence: ledger:E0281, ledger:E0290</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25A3E" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD0" flags="0x30">
    <title>O2 Switch Point Adder vs O2 Activity</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Adder to the O2 switch point vs how fast the O2 voltage is changing, phased in after a start by the term-A delay/ramp. Stock 0 to +100 mV. The oxygen sensor input here is the rear (post catalyst) sensor, bank 1 sensor 2. Effect: raise = switch point moves up (richer) when the O2 signal is active Evidence: ledger:E0281, ledger:E0988, ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>mV (change of filtered O2 voltage over 10 updates)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-20" />
      <LABEL index="1" value="-18.75" />
      <LABEL index="2" value="-17.5" />
      <LABEL index="3" value="-16.25" />
      <LABEL index="4" value="-15" />
      <LABEL index="5" value="-13.75" />
      <LABEL index="6" value="-12.5" />
      <LABEL index="7" value="-11.25" />
      <LABEL index="8" value="-10" />
      <LABEL index="9" value="-8.75" />
      <LABEL index="10" value="-7.5" />
      <LABEL index="11" value="-6.25" />
      <LABEL index="12" value="-5" />
      <LABEL index="13" value="-3.75" />
      <LABEL index="14" value="-2.5" />
      <LABEL index="15" value="-1.25" />
      <LABEL index="16" value="0" />
      <LABEL index="17" value="1.25" />
      <LABEL index="18" value="2.5" />
      <LABEL index="19" value="3.75" />
      <LABEL index="20" value="5" />
      <LABEL index="21" value="6.25" />
      <LABEL index="22" value="7.5" />
      <LABEL index="23" value="8.75" />
      <LABEL index="24" value="10" />
      <LABEL index="25" value="11.25" />
      <LABEL index="26" value="12.5" />
      <LABEL index="27" value="13.75" />
      <LABEL index="28" value="15" />
      <LABEL index="29" value="16.25" />
      <LABEL index="30" value="17.5" />
      <LABEL index="31" value="18.75" />
      <LABEL index="32" value="20" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25868" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD1" flags="0x30">
    <title>O2 Switch Point Adder vs Filtered O2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Adder to the O2 switch point vs the filtered O2 voltage, phased in after a start by the term-B delay/ramp. Stock +150 mV at 250 mV falling to -75 mV at high voltage. The oxygen sensor input here is the rear (post catalyst) sensor, bank 1 sensor 2. Effect: raise = switch point moves up (richer) at that O2 voltage Evidence: ledger:E0281, ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>mV</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="250" />
      <LABEL index="1" value="271.875" />
      <LABEL index="2" value="293.75" />
      <LABEL index="3" value="315.625" />
      <LABEL index="4" value="337.5" />
      <LABEL index="5" value="359.375" />
      <LABEL index="6" value="381.25" />
      <LABEL index="7" value="403.125" />
      <LABEL index="8" value="425" />
      <LABEL index="9" value="446.875" />
      <LABEL index="10" value="468.75" />
      <LABEL index="11" value="490.625" />
      <LABEL index="12" value="512.5" />
      <LABEL index="13" value="534.375" />
      <LABEL index="14" value="556.25" />
      <LABEL index="15" value="578.125" />
      <LABEL index="16" value="600" />
      <LABEL index="17" value="621.875" />
      <LABEL index="18" value="643.75" />
      <LABEL index="19" value="665.625" />
      <LABEL index="20" value="687.5" />
      <LABEL index="21" value="709.375" />
      <LABEL index="22" value="731.25" />
      <LABEL index="23" value="753.125" />
      <LABEL index="24" value="775" />
      <LABEL index="25" value="796.875" />
      <LABEL index="26" value="818.75" />
      <LABEL index="27" value="840.625" />
      <LABEL index="28" value="862.5" />
      <LABEL index="29" value="884.375" />
      <LABEL index="30" value="906.25" />
      <LABEL index="31" value="928.125" />
      <LABEL index="32" value="950" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x258B0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xD2" flags="0x0">
    <title>O2 Switch Point Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest O2 switch point allowed. Stock 300 mV. Effect: raise = closed loop cannot be biased as lean Evidence: ledger:E0281</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25958" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD3" flags="0x0">
    <title>O2 Switch Point Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest O2 switch point allowed. Stock 675 mV. Effect: raise = closed loop can be biased richer Evidence: ledger:E0281</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2595A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD4" flags="0x0">
    <title>O2 Switch Point Cold-Start Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the O2 switch point while the engine has run less than the time limit and coolant is below the temperature limit. Stock -150 mV (leaner bias when cold). Effect: raise = less lean bias just after a cold start Evidence: ledger:E0281</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25928" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD5" flags="0x0">
    <title>O2 Switch Point Cold-Start Adder - Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Run time after start during which the cold-start adder applies. Stock 160 s. Effect: raise = cold-start bias lasts longer Evidence: ledger:E0281</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25924" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD6" flags="0x0">
    <title>O2 Switch Point Cold-Start Adder - Coolant Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cold-start adder applies only below this coolant temperature. Stock 65 C. Effect: raise = cold-start bias applies to warmer starts Evidence: ledger:E0281</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25926" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD7" flags="0x0">
    <title>Idle Airflow Area Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit on the idle airflow (effective throttle area) command in normal running. Stock 3.33 % of full throttle area (about 30 g/s-equivalent at idle). The idle controller cannot open the throttle further than this at idle. Effect: raise = idle control can add more air (big cams, cold starts); too high risks runaway idle Evidence: ledger:E0282, ledger:E0283</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x296AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>182.041667</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/360"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD8" flags="0x0">
    <title>Idle Airflow Area Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower limit on the idle airflow command in normal running. Stock 0. Effect: raise = throttle never closes below this at idle Evidence: ledger:E0282, ledger:E0283</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x296B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>182.041667</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/360"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD9" flags="0x0">
    <title>Idle Airflow Area Maximum - Fault</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit used when a sensor-fault condition is active (e.g. MAF fault). Stock 11.4 %. Effect: limit used only with a fault present Evidence: ledger:E0282, ledger:E0283</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x296AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>182.041667</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/360"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDA" flags="0x0">
    <title>Idle Airflow Area Minimum - Fault</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower limit used when a sensor-fault condition is active. Stock 0. Effect: limit used only with a fault present Evidence: ledger:E0282, ledger:E0283</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x296AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>182.041667</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/360"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDB" flags="0x0">
    <title>Idle Airflow Area - Fault Default</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Command forced when the idle controller&#x27;s fault flag is set. Stock 0. Effect: value used only with that fault Evidence: ledger:E0282, ledger:E0283</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x296B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>182.041667</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/360"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xDC" flags="0x30">
    <title>Idle Airflow - Barometric Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added vs barometric pressure (altitude). Stock -1.11 g/s at 60 kPa rising to 0 at 100 kPa. Effect: raise = more idle air at altitude Evidence: ledger:E0286, ledger:E0287</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="60" />
      <LABEL index="1" value="65" />
      <LABEL index="2" value="70" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="80" />
      <LABEL index="5" value="85" />
      <LABEL index="6" value="90" />
      <LABEL index="7" value="95" />
      <LABEL index="8" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29E9A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDD" flags="0x30">
    <title>Idle Overspeed Spark / Droop Airflow Gain vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales rpm error vs coolant for two things: the overspeed idle spark tables and the rpm-below-desired input of Idle Airflow vs RPM Below Desired. Stock 1.0 everywhere (E0291). Effect: raise = the droop table reacts to smaller rpm sags Evidence: ledger:E0286, ledger:E0287, ledger:E0291</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A5D2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDE" flags="0x30">
    <title>Idle Start-Up RPM Flare - In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra desired idle rpm after a start (added to the desired idle vs coolant value, E0294) vs time since start (rows) and coolant (columns), In Gear. Stock 200 rpm at start (300 rpm at 20 and 32 C) decaying to 0 by 64 s. The Idle Airflow vs Start-Up RPM Flare table supplies the air for it; after 8 s it is cancelled once the truck moves or the throttle opens. Effect: raise = higher, longer rpm flare after starting Evidence: ledger:E0286, ledger:E0287, ledger:E0294</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>s since start</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A0E4" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDF" flags="0x30">
    <title>Idle Airflow - Light-Off Retard Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added while catalyst light-off spark retard is active, vs the amount of retard, used normally. Stock 0 to 0.32 g/s. Effect: raise = more air to hold idle rpm while spark is retarded Evidence: ledger:E0286, ledger:E0287, ledger:E0294</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>deg retard</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29EF6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE0" flags="0x30">
    <title>Idle Airflow - Light-Off Retard Adder (A/C)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added while catalyst light-off spark retard is active, vs the amount of retard, used with A/C on (or the alternate state). Stock 0 to 0.64 g/s. Effect: raise = more air to hold idle rpm while spark is retarded Evidence: ledger:E0286, ledger:E0287, ledger:E0294</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>deg retard</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29F02" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE1" flags="0x30">
    <title>Idle Airflow - Base vs RPM</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base idle airflow term vs engine speed, part of the closed-loop term. Stock 0.3 g/s at 400-800 rpm, 1.0 (In Gear) / 0.5 (Park/Neutral) at 1200 rpm, rising to 20 g/s at 6400 rpm. Row 1 = In Gear, row 2 = Park/Neutral. Effect: raise = more idle air at that rpm Evidence: ledger:E0287, ledger:E0289</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29262" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE2" flags="0x30">
    <title>Idle Airflow - RPM Adder (timed)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added by engine speed, 400 to 3600 rpm, while its timer gate allows (the gate timing itself is not fully traced). It passes straight into the idle throttle area. Stock 0 up to 1600 rpm, then 0.1 to 1.0 g/s at 3600 rpm (E0723). Effect: raise = more air when rpm is high with the throttle closed (softer return to idle) Evidence: ledger:E0287, ledger:E0289, ledger:E0723</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1000" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1400" />
      <LABEL index="6" value="1600" />
      <LABEL index="7" value="1800" />
      <LABEL index="8" value="2000" />
      <LABEL index="9" value="2200" />
      <LABEL index="10" value="2400" />
      <LABEL index="11" value="2600" />
      <LABEL index="12" value="2800" />
      <LABEL index="13" value="3000" />
      <LABEL index="14" value="3200" />
      <LABEL index="15" value="3400" />
      <LABEL index="16" value="3600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2934E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE3" flags="0x30">
    <title>Idle Airflow Closed-Loop Step vs Airflow Error</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Step added to the idle airflow integral each control update, by airflow error (measured flow minus predicted idle airflow). STOCK IS ALL ZERO: the airflow integral is switched off on this calibration and idle rpm is held by the learn, the rpm-droop airflow table and idle spark. Filling it enables the integral; start very small. Row 1 = In Gear, row 2 = Park/Neutral. Effect: non-zero = enables airflow closed-loop idle; positive values for positive error remove air (check the sign on a log first) Evidence: ledger:E0287, ledger:E0289</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x29314" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT; data columns: g/s airflow error)</units>
      <embedinfo type="1" />
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2921A" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s per update</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE4" flags="0x30">
    <title>Idle Airflow Closed-Loop Error Gain vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the airflow error before the closed-loop step lookup, vs coolant. Stock 1.0. Effect: raise = the step table reacts to smaller errors Evidence: ledger:E0287, ledger:E0289</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29526" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE5" flags="0x0">
    <title>Idle Airflow Learn Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper clamp on the learned idle airflow. Stock 3.5 g/s. Effect: widens or narrows how far the idle airflow learn can move Evidence: ledger:E0287, ledger:E0289</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE6" flags="0x0">
    <title>Idle Airflow Learn Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower clamp on the learned idle airflow. Stock 0. Effect: widens or narrows how far the idle airflow learn can move Evidence: ledger:E0287, ledger:E0289</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE7" flags="0x30">
    <title>Idle Underspeed Spark Gain vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the idle underspeed spark tables (both P/N and In Gear) vs coolant. Stock 1.0 everywhere. Effect: raise = more spark advance added when idle rpm sags Evidence: ledger:E0291</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A5AE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE8" flags="0x30">
    <title>O2 Switch Point Airflow Map</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Maps used airflow onto the columns of O2 Switch Point - Base (value = column, 0 to 8). Stock reaches the last column at 76 g/s, so the base curve spends most of its resolution below 30 g/s. Effect: reshapes where along airflow each base switch-point column applies Evidence: ledger:E0290</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s used airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <LABEL index="17" value="68" />
      <LABEL index="18" value="72" />
      <LABEL index="19" value="76" />
      <LABEL index="20" value="80" />
      <LABEL index="21" value="84" />
      <LABEL index="22" value="88" />
      <LABEL index="23" value="92" />
      <LABEL index="24" value="96" />
      <LABEL index="25" value="100" />
      <LABEL index="26" value="104" />
      <LABEL index="27" value="108" />
      <LABEL index="28" value="112" />
      <LABEL index="29" value="116" />
      <LABEL index="30" value="120" />
      <LABEL index="31" value="124" />
      <LABEL index="32" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25BD6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>base column</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE9" flags="0x30">
    <title>Throttle Follower Airflow vs RPM</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Follower airflow target vs rpm, before its throttle (stock 0.5), speed (0.68 at standstill), coolant and baro factors. Rows: normal In Gear, normal Park/Neutral, first idle after start In Gear, first idle P/N. Stock In Gear 2.4 (400 rpm) to 40 (6400 rpm). Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually ins...</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A7F2" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xEA" flags="0x30">
    <title>Throttle Follower Factor vs Throttle</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the follower target vs the current throttle. Rows: normal, first idle after start. Stock 0.5 everywhere. Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually instead of snapping shut (executed in the scheduler rig: a lift from 2000 rpm held about 3.5 g/s extra for about 0.8 s, then decayed to zero by abo...</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x2AA76" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT; data columns: % throttle)</units>
      <embedinfo type="1" />
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A912" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xEB" flags="0x30">
    <title>Throttle Follower Factor vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the follower target vs vehicle speed. Stock 0.68 at 0-14 km/h, 1.0 above. Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually instead of snapping shut (executed in the scheduler rig: a lift from 2000 rpm held about 3.5 g/s extra for about 0.8 s, then decayed to zero by about 1.8 s; with the follower airflow table zeroed the extra air and throttle opening were absent). Effect: raise = more follower...</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="14" />
      <LABEL index="2" value="28" />
      <LABEL index="3" value="42" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="70" />
      <LABEL index="6" value="84" />
      <LABEL index="7" value="98" />
      <LABEL index="8" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AA9C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>3.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xEC" flags="0x30">
    <title>Throttle Follower Factor vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the follower target vs coolant. Stock 1.5 at 20 and 32 C, 1.0 elsewhere. Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually instead of snapping shut (executed in the scheduler rig: a lift from 2000 rpm held about 3.5 g/s extra for about 0.8 s, then decayed to zero by about 1.8 s; with the follower airflow table zeroed the extra air and throttle opening were absent). Effect: raise = more follower a...</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AA0C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xED" flags="0x30">
    <title>Throttle Follower Decay Step vs RPM</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the follower air bleeds off once the hold time has passed, per control update. Stock In Gear 0.005 g/s at 400 rpm to 0.09 g/s above 2000 rpm; P/N about half. Rows: In Gear, Park/Neutral. Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually instead of snapping shut (executed in the scheduler rig: a lift...</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A882" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s per update</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>31.999512</max>
      <MATH equation="X/2048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xEE" flags="0x30">
    <title>Throttle Follower Decay Factor vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the decay step vs vehicle speed. Stock 1.0 to 42 km/h, rising to 5.0 at 63-105 km/h. Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually instead of snapping shut (executed in the scheduler rig: a lift from 2000 rpm held about 3.5 g/s extra for about 0.8 s, then decayed to zero by about 1.8 s; with the follower airflow table zeroed the extra air and throttle opening were absent). Effect: raise = fas...</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="7" />
      <LABEL index="2" value="14" />
      <LABEL index="3" value="21" />
      <LABEL index="4" value="28" />
      <LABEL index="5" value="35" />
      <LABEL index="6" value="42" />
      <LABEL index="7" value="49" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="63" />
      <LABEL index="10" value="70" />
      <LABEL index="11" value="77" />
      <LABEL index="12" value="84" />
      <LABEL index="13" value="91" />
      <LABEL index="14" value="98" />
      <LABEL index="15" value="105" />
      <LABEL index="16" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AA30" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xEF" flags="0x30">
    <title>Throttle Follower Hold Time vs RPM</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the follower air is held before it starts to bleed off. Stock In Gear 0.1 s at 0-800 rpm, 1.0 s at 1200, 0.3-0.4 s above 2000. Rows: In Gear, Park/Neutral. Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually instead of snapping shut (executed in the scheduler rig: a lift from 2000 rpm held about 3.5 g...</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A95A" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xF0" flags="0x30">
    <title>Throttle Follower Hold Factor vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the hold time vs vehicle speed. Stock 2.0 at standstill, 1.5 at 7-35 km/h, 1.0 above. Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually instead of snapping shut (executed in the scheduler rig: a lift from 2000 rpm held about 3.5 g/s extra for about 0.8 s, then decayed to zero by about 1.8 s; with the follower airflow table zeroed the extra air and throttle opening were absent). Effect: raise = lo...</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="7" />
      <LABEL index="2" value="14" />
      <LABEL index="3" value="21" />
      <LABEL index="4" value="28" />
      <LABEL index="5" value="35" />
      <LABEL index="6" value="42" />
      <LABEL index="7" value="49" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="63" />
      <LABEL index="10" value="70" />
      <LABEL index="11" value="77" />
      <LABEL index="12" value="84" />
      <LABEL index="13" value="91" />
      <LABEL index="14" value="98" />
      <LABEL index="15" value="105" />
      <LABEL index="16" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AA54" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xF1" flags="0x30">
    <title>Idle Airflow Kick - Shift into P/N</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short airflow kick after shifting into Park/Neutral, by accessory state (A/C off/on x a second flag off/on; the second flag is a dead/always-0 snapshot on stock, E0824). Stock 0.2 g/s. Added straight into the idle airflow request for about 0.2 s, then faded out (E0293). Effect: raise = more air right after shifting to P/N Evidence: ledger:E0287, ledger:E0293, ledger:E0824, ledger:E1113</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="base" />
      <LABEL index="1" value="A/C" />
      <LABEL index="2" value="row 2 (dead on stock)" />
      <LABEL index="3" value="row 3 (dead on stock)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A620" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xF2" flags="0x30">
    <title>Idle Airflow Kick - Shift into Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short airflow kick after shifting into gear (the converter loads the engine), by accessory state (A/C off/on x a second flag off/on; the second flag is a dead/always-0 snapshot on stock, E0824). Stock 0.2 g/s. Added straight into the idle airflow request for about 0.2 s, then faded out (E0293). Effect: raise = more air right after shifting into gear (less rpm dip on engagement) Evidence: ledger:E0287, ledger:E0293, ledger:E0824</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="base" />
      <LABEL index="1" value="A/C" />
      <LABEL index="2" value="row 2 (dead on stock)" />
      <LABEL index="3" value="row 3 (dead on stock)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A628" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>31.999512</max>
      <MATH equation="X/2048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xF3" flags="0x30">
    <title>Idle Airflow Shift into P/N Kick Factor vs Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the shift-into-P/N kick vs transmission fluid temperature. Stock 1.0. Added straight into the idle airflow request for about 0.2 s, then faded out (E0293). Effect: raise = bigger kick at that fluid temperature Evidence: ledger:E0287, ledger:E0293</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A6E8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xF4" flags="0x30">
    <title>Idle Airflow Shift into Gear Kick Factor vs Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the shift-into-gear kick vs transmission fluid temperature. Stock 1.0. Added straight into the idle airflow request for about 0.2 s, then faded out (E0293). Effect: raise = bigger kick at that fluid temperature Evidence: ledger:E0287, ledger:E0293</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A730" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xF5" flags="0x0">
    <title>Idle Airflow Kick - Shift into P/N Duration</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the kick is held before it fades. Stock 0.2 s. Added straight into the idle airflow request for about 0.2 s, then faded out (E0293). Effect: raise = kick lasts longer Evidence: ledger:E0293</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A64C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xF6" flags="0x0">
    <title>Idle Airflow Kick - Shift into Gear Duration</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the kick is held before it fades. Stock 0.2 s. Added straight into the idle airflow request for about 0.2 s, then faded out (E0293). Effect: raise = kick lasts longer Evidence: ledger:E0293</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A652" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xF7" flags="0x30">
    <title>Idle Airflow - Post-Start (first second)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow added right after the engine starts, vs time since start (columns, 0.5 s steps) and coolant (rows), until the Post-Start Time Limit passes. Stock 1.5 to 3.0 g/s for about the first second; later columns are never reached on stock limits. Effect: raise = more air in the first moment after start (helps a stumble or dip right after crank) Evidence: ledger:E0287, ledger:E0294, ledger:E0936</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>s since start</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.5" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="1.5" />
      <LABEL index="4" value="2" />
      <LABEL index="5" value="2.5" />
      <LABEL index="6" value="3" />
      <LABEL index="7" value="3.5" />
      <LABEL index="8" value="4" />
      <LABEL index="9" value="4.5" />
      <LABEL index="10" value="5" />
      <LABEL index="11" value="5.5" />
      <LABEL index="12" value="6" />
      <LABEL index="13" value="6.5" />
      <LABEL index="14" value="7" />
      <LABEL index="15" value="7.5" />
      <LABEL index="16" value="8" />
      <LABEL index="17" value="8.5" />
      <LABEL index="18" value="9" />
      <LABEL index="19" value="9.5" />
      <LABEL index="20" value="10" />
      <LABEL index="21" value="10.5" />
      <LABEL index="22" value="11" />
      <LABEL index="23" value="11.5" />
      <LABEL index="24" value="12" />
      <LABEL index="25" value="12.5" />
      <LABEL index="26" value="13" />
      <LABEL index="27" value="13.5" />
      <LABEL index="28" value="14" />
      <LABEL index="29" value="14.5" />
      <LABEL index="30" value="15" />
      <LABEL index="31" value="15.5" />
      <LABEL index="32" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2975C" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xF8" flags="0x30">
    <title>Idle Airflow - Post-Start Time Limit (rpm above desired)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long after start the post-start airflow stays on, while rpm is above desired, vs coolant. Stock 1.5 s cold, 0.85 s from 20 C. Effect: raise = post-start air stays on longer Evidence: ledger:E0294</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29BC0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xF9" flags="0x30">
    <title>Idle Airflow - Post-Start Time Limit (rpm at or below desired)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long after start the post-start airflow stays on, while rpm is at or below desired, vs coolant. Stock 1.0 s cold, 0.85 s from 20 C. Effect: raise = post-start air stays on longer Evidence: ledger:E0294</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29BE4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xFA" flags="0x0">
    <title>Coolant Hot Flag - On Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant temperature above which the PCM sets its coolant-hot status flag (sent to other modules). Stock 125 C. Effect: raise = hot flag comes on later Evidence: ledger:E0297</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x2283C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xFB" flags="0x0">
    <title>Coolant Hot Flag - Off Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant temperature below which the coolant-hot flag clears. Stock 122 C. Effect: keep below the On value Evidence: ledger:E0297</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x2283A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xFC" flags="0x0">
    <title>Coolant Over-Temp Flag 2 - On Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Second, higher coolant over-temperature flag, also broadcast to other modules on the vehicle network. Stock 129 C. Effect: raise = second flag comes on later Evidence: ledger:E0297</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x22840" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xFD" flags="0x0">
    <title>Coolant Over-Temp Flag 2 - Off Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant temperature below which the second over-temperature flag clears. Stock 126 C. Effect: keep below the On value Evidence: ledger:E0297</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x2283E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xFE" flags="0x0">
    <title>Catalyst Over-Temp Protection - Enter Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Modelled catalyst temperature above which over-temperature fuel enrichment ramps in. Stock 1015 C. Effect: lower = protection enrichment starts sooner (richer, cooler cats) Evidence: ledger:E0298</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x218B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xFF" flags="0x0">
    <title>Catalyst Over-Temp Protection - Enter Above (conditional)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower entry temperature used while protection was already active on the previous update. Stock 980 C. Effect: lower = protection starts sooner in that condition Evidence: ledger:E0298</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x218BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x100" flags="0x0">
    <title>Catalyst Over-Temp Protection - Exit Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Modelled catalyst temperature below which the protection enrichment ramps back out. Stock 965 C. Effect: keep below the entry temperatures Evidence: ledger:E0298</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x218BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x101" flags="0x0">
    <title>Catalyst Over-Temp Protection - Maximum EQ</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cap on commanded fuel (equivalence ratio) while protection enrichment is active. Stock 1.450 (lambda 0.69). Effect: raise = richer maximum protection fuel Evidence: ledger:E0298</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x218BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>EQ</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x102" flags="0x0">
    <title>Catalyst Over-Temp Protection - Minimum Ramp-Out Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Smallest step by which protection enrichment is removed each update once the catalyst cools. Stock 0.040 EQ. Effect: raise = enrichment leaves faster Evidence: ledger:E0298</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x218C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>EQ per update</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x103" flags="0x30">
    <title>Cranking Spark vs RPM vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark advance used while cranking, by coolant (rows) and engine speed (columns). Stock 3 to 12 deg. Effect: more advance = can start faster but risks kickback; less = softer, slower starts Evidence: ledger:E0299</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="50" />
      <LABEL index="2" value="100" />
      <LABEL index="3" value="150" />
      <LABEL index="4" value="200" />
      <LABEL index="5" value="250" />
      <LABEL index="6" value="300" />
      <LABEL index="7" value="350" />
      <LABEL index="8" value="400" />
      <LABEL index="9" value="450" />
      <LABEL index="10" value="500" />
      <LABEL index="11" value="550" />
      <LABEL index="12" value="600" />
      <LABEL index="13" value="650" />
      <LABEL index="14" value="700" />
      <LABEL index="15" value="750" />
      <LABEL index="16" value="800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>10</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <LABEL index="9" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2D0E1" mmedelementsizebits="8" mmedrowcount="10" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x104" flags="0x0">
    <title>LTFT Maximum Adjustment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest value a long-term fuel trim cell can learn. Stock 1.25 (+25 % fuel). Effect: raise = trims can add more fuel Evidence: ledger:E0300</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2568A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x105" flags="0x0">
    <title>LTFT Minimum Adjustment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest value a long-term fuel trim cell can learn. Stock 0.60 (-40 % fuel). Effect: lower = trims can remove more fuel Evidence: ledger:E0300</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2568C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x106" flags="0x0">
    <title>LTFT Idle Cell - Throttle Enter Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle trim cell is used when throttle is below this (and speed below its limit). Stock 0.10 %. Effect: raise = idle cell used with slightly open throttle Evidence: ledger:E0300</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2566C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x107" flags="0x0">
    <title>LTFT Idle Cell - Throttle Leave Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle trim cell is left when throttle rises above this. Stock 0.20 %. Effect: keep above the enter value Evidence: ledger:E0300</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2566A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x108" flags="0x0">
    <title>LTFT Idle Cell - Speed Enter Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle trim cell is used below this vehicle speed. Stock 3 km/h. Effect: raise = idle cell used while rolling slowly Evidence: ledger:E0300</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25670" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x109" flags="0x0">
    <title>LTFT Idle Cell - Speed Leave Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle trim cell is left above this vehicle speed. Stock 6 km/h. Effect: keep above the enter value Evidence: ledger:E0300</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2566E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x10A" flags="0x0">
    <title>Clear Flood - Throttle Enable Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While cranking, throttle above this switches cranking fuel to its clear-flood mode (for a flooded engine). Stock 90 %. Effect: lower = clear flood engages at less throttle Evidence: ledger:E0301</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26A64" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x10B" flags="0x0">
    <title>Clear Flood - Throttle Disable Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Clear-flood mode ends when throttle falls below this. Stock 85 %. Effect: keep below the enable value Evidence: ledger:E0301</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26A66" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x10C" flags="0x0">
    <title>Output Shaft Sensor Pulses Per Rev</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of pulses the transmission output-shaft speed sensor makes per shaft revolution. The PCM divides by it to turn sensor pulses into output-shaft rpm, which drives vehicle speed, the speedometer and every speed-based table. Stock H3 40. It describes the sensor hardware: change it only for a different reluctor, never to correct the speedometer (use axle ratio and tire revs for that) (E0303). Effect: output-shaft rpm and vehicle speed scale as 1 / value Evidence: ledger:E0303</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3DF2A" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>pulses/rev</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x10D" flags="0x0">
    <title>PE Delay - Coolant Bypass Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Power enrichment is delayed only while coolant is at or above this; colder, PE comes in with no delay. Stock 0 C. Effect: raise = no PE delay over a wider cold range Evidence: ledger:E0307</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28BA6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x10E" flags="0x0">
    <title>PE Delay - Coolant Bypass Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Power enrichment is delayed only while coolant is at or below this; hotter, PE comes in with no delay. Stock 110 C. Effect: lower = no PE delay on a hot engine sooner Evidence: ledger:E0307</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28BA8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x10F" flags="0x0">
    <title>PE Delay - Throttle Rise Bypass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A throttle rise at least this big since the last update skips the PE delay, but only below the speed bypass value. Stock 10 %. Effect: lower = smaller stabs of throttle skip the delay Evidence: ledger:E0307</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28BAC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% per update</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x110" flags="0x0">
    <title>PE Delay - Speed Bypass Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this vehicle speed a fast throttle rise skips the PE delay (for full-throttle launches). At or above it the delay always applies. Stock 8 km/h. Effect: raise = throttle-stab bypass works at higher speeds Evidence: ledger:E0307</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28BAE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x111" flags="0x0">
    <title>PE Delay - Maximum Delay Store</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PE delay store fills with time spent out of power enrichment, up to this cap, and must drain before a delayed PE request takes effect. It drains at the rate set by the PE Delay Countdown Rate table. Stock 14.0 s. Effect: lower = shorter maximum PE delay; 0 = no delay Evidence: ledger:E0307</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28BB4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x112" flags="0x0">
    <title>Closed Loop Idle - Throttle Enter Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel switches to its idle settings (short-term trim steps, O2 switch point) when throttle is below this and speed is below its limit. Stock 0.10 %. Effect: raise = idle settings used with slightly open throttle Evidence: ledger:E0305</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2595E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x113" flags="0x0">
    <title>Closed Loop Idle - Throttle Leave Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel leaves its idle settings when throttle reaches this. Stock 0.20 %. Effect: keep above the enter value Evidence: ledger:E0305</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2595C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x114" flags="0x0">
    <title>Closed Loop Idle - Speed Enter Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel uses its idle settings below this vehicle speed. Stock 3 km/h. Effect: raise = idle settings used while rolling slowly Evidence: ledger:E0305</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25962" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x115" flags="0x0">
    <title>Closed Loop Idle - Speed Leave Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel leaves its idle settings at this vehicle speed. Stock 6 km/h. Effect: keep above the enter value Evidence: ledger:E0305</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25960" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x116" flags="0x0">
    <title>DFCO Exit - RPM Drop per Update</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While in decel fuel cut, an engine speed fall of at least this much between two updates ends the cut (guards against stalling when rpm drops fast). Stock 300 rpm. Effect: lower = fuel returns on smaller rpm drops Evidence: ledger:E0308</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2F500" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x117" flags="0x30">
    <title>DFCO Exit - Minimum RPM vs Desired Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While in decel fuel cut, engine speed below this (looked up from the current desired idle) ends the cut. Stock 700 rpm at 800 rpm desired idle, 500 at 600. Effect: raise = fuel returns at a higher rpm (less chance of stalling, less fuel saved) Evidence: ledger:E0308</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1000" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1400" />
      <LABEL index="6" value="1600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F504" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x118" flags="0x30">
    <title>LTFT Cell RPM Boundaries</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speeds that split the long-term fuel trim cells into 4 rpm columns (a column runs up to and including its boundary). Stock 100 / 6000 / 6500 rpm, so normal driving is all one column. Effect: spread these out to learn separate trims for different rpm bands (keep them rising) Evidence: ledger:E0310</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>boundary</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25678" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x119" flags="0x30">
    <title>LTFT Cell MAP Boundaries</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Manifold pressures that split the long-term fuel trim cells into 4 MAP rows. Stock 5 / 60 / 110 kPa, so normal driving uses two rows split at 60 kPa. Effect: move these to change which loads share a learned trim (keep them rising) Evidence: ledger:E0310</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>boundary</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2567E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x11A" flags="0x0">
    <title>LTFT Cell RPM Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once in an LTFT cell, rpm must pass its boundaries by this much to change column. Stock 50 rpm. Effect: raise = fewer cell changes near a boundary Evidence: ledger:E0310</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25674" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x11B" flags="0x0">
    <title>LTFT Cell MAP Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once in a long-term fuel trim cell, manifold pressure must pass the cell&#x27;s row boundaries by this much before the trim moves to another row. Stock 2 kPa. Effect: raise = fewer cell changes near a boundary Evidence: ledger:E0310, ledger:E1369</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25676" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x11C" flags="0x0">
    <title>LTFT Learn Deadband</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short-term trim must be more than this far from 0 % before the long-term cell learns up or down. Stock 3.0 %. Effect: lower = long-term trims follow smaller errors (more hunting); higher = only larger errors are learned Evidence: ledger:E0311</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25692" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x11D" flags="0x30">
    <title>LTFT Learn Minimum MAP vs Baro</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim only learns when MAP is at least this, looked up from barometric pressure. Stock 0 at every point: no limit. Effect: raise = long term trim does not learn below this manifold pressure Evidence: ledger:E0311, ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="65" />
      <LABEL index="1" value="70" />
      <LABEL index="2" value="75" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="85" />
      <LABEL index="5" value="90" />
      <LABEL index="6" value="95" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25696" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x11E" flags="0x30">
    <title>Transmission Gear Ratios (1st-4th)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM&#x27;s copy of the 4L60-E gear ratios (stock 3.06 / 1.63 / 1.00 / 0.70). Used to work out the transfer-case ratio for 4-Lo detection. Change only for a transmission with different ratios (E0337). A second copy at x2048 (Transmission Gear Ratios, second copy) feeds the torque estimate: change both (E0337). Effect: 4-Lo detection (transfer-case ratio) and any logic that divides by the current gear ratio Evidence: ledger:E0337</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E9A6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>:1</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x11F" flags="0x0">
    <title>Transfer Case Low Range Ratio (4-Lo)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Low-range reduction of the transfer case, stock 4.03. The speed sensor sits after the transfer case, so in 4-Lo the PCM multiplies it by this value to get true transmission output speed for shifting and TCC, and divides it out of rpm per speed. Change it only for a transfer case with a different low range, and move the Low Range Detection band to match or 4-Lo will not be detected (E0314). Code-proven, not yet confirmed on a drive. Effect: 4-Lo shift points and TCC (trans output speed); vehicle speed is not affected Evidence: ledger:E0314, ledger:E0808</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF1A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>:1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x120" flags="0x0">
    <title>P2771 Fault Test, High Range Assumed - Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, high range assumed: bottom of the window of engine speed over (output speed x gear ratio) that means the transfer case is really in low range. Stock window 3.700 to 4.280. After the code sets, the PCM treats the range as low. Effect: raise = lower ratios no longer count as low range Evidence: ledger:E0314, ledger:E0808, ledger:E1099</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F752" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>:1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x121" flags="0x0">
    <title>P2771 Fault Test, High Range Assumed - Ratio Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, high range assumed: top of the window of engine speed over (output speed x gear ratio) that means the transfer case is really in low range. Stock window 3.700 to 4.280. Effect: lower = higher ratios no longer count as low range Evidence: ledger:E0314, ledger:E0808, ledger:E1099</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F754" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>:1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x122" flags="0x30">
    <title>Transient Fuel - Wall Deposit Fraction vs MAP vs Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of each injection that sticks to the intake port wall instead of entering the cylinder (the wall-wetting &#x27;X&#x27;), by MAP (rows) and port temperature (columns). The PCM adds fuel to make up for it on tip-in and removes it on tip-out. Stock 0.75 cold to 0.37 hot. Effect: raise = more tip-in fuel and more tip-out fuel removal (fixes lean stumble on tip-in / rich on tip-out) Evidence: ledger:E0316</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (port temp model)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-24" />
      <LABEL index="2" value="-8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="24" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="56" />
      <LABEL index="7" value="72" />
      <LABEL index="8" value="88" />
      <LABEL index="9" value="104" />
      <LABEL index="10" value="120" />
      <LABEL index="11" value="136" />
      <LABEL index="12" value="152" />
      <LABEL index="13" value="168" />
      <LABEL index="14" value="184" />
      <LABEL index="15" value="200" />
      <LABEL index="16" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="20" />
      <LABEL index="1" value="30" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="50" />
      <LABEL index="4" value="60" />
      <LABEL index="5" value="70" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="90" />
      <LABEL index="8" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26784" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x123" flags="0x30">
    <title>Transient Fuel - Deposit Multiplier vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the wall deposit fraction by engine airflow. Stock 1.0 everywhere. Effect: below 1.0 = less wall-wetting compensation at that airflow Evidence: ledger:E0316</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="8" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="24" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="48" />
      <LABEL index="7" value="56" />
      <LABEL index="8" value="64" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="88" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="104" />
      <LABEL index="14" value="112" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="128" />
      <LABEL index="17" value="136" />
      <LABEL index="18" value="144" />
      <LABEL index="19" value="152" />
      <LABEL index="20" value="160" />
      <LABEL index="21" value="168" />
      <LABEL index="22" value="176" />
      <LABEL index="23" value="184" />
      <LABEL index="24" value="192" />
      <LABEL index="25" value="200" />
      <LABEL index="26" value="208" />
      <LABEL index="27" value="216" />
      <LABEL index="28" value="224" />
      <LABEL index="29" value="232" />
      <LABEL index="30" value="240" />
      <LABEL index="31" value="248" />
      <LABEL index="32" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x268BA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x124" flags="0x30">
    <title>Transient Fuel - Tip-Out Correction Multiplier vs Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transient fuel, tip-out mode: while the mode is on (after a sudden MAP fall, until the throttle opens again or the wall film stops shrinking) the wall film fuel correction is multiplied by this, by port temperature. On a tip-out the correction removes fuel, so a larger value removes more. Stock 1.5 cold, 0.7 hot. Effect: raise = more fuel is taken out on a throttle lift Evidence: ledger:E0316, ledger:E1125</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (port temp model)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-24" />
      <LABEL index="2" value="-8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="24" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="56" />
      <LABEL index="7" value="72" />
      <LABEL index="8" value="88" />
      <LABEL index="9" value="104" />
      <LABEL index="10" value="120" />
      <LABEL index="11" value="136" />
      <LABEL index="12" value="152" />
      <LABEL index="13" value="168" />
      <LABEL index="14" value="184" />
      <LABEL index="15" value="200" />
      <LABEL index="16" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2675C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>3.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x125" flags="0x0">
    <title>Transient Fuel - MAP Filter Coefficient</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transient fuel: how fast the filtered MAP follows real MAP. The tip-out mode is detected as MAP falling below this filtered value. Stock 0.20 of the gap per update. Effect: lower = slower filter, the tip-out mode is detected more easily and for longer Evidence: ledger:E0316, ledger:E1125</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26750" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x126" flags="0x0">
    <title>Transient Fuel - Tip-Out MAP Fall Trigger</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transient fuel, tip-out mode: the mode starts when manifold pressure is more than this below its filtered value, that is when MAP is falling fast. Stock 2.0 kPa. Effect: lower = the tip-out mode starts on smaller MAP drops Evidence: ledger:E0316, ledger:E1125</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26754" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x127" flags="0x0">
    <title>Transient Fuel - Tip-Out End on Throttle Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transient fuel, tip-out mode: the mode ends when the throttle rises by more than this between updates. Stock 0 %: any opening of the throttle ends it. Effect: raise = the tip-out mode survives a small throttle opening Evidence: ledger:E0316, ledger:E1125</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26756" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>% per update</units>
    <decimalpl>3</decimalpl>
    <min>-200.000000</min>
    <max>199.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x128" flags="0x0">
    <title>Transient Fuel - Evaporation Cap</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit on the wall-film evaporation fraction, as a share of (1 - deposit fraction). Stock 0.9995 (no practical limit). Effect: lower = limits how fast the wall film can dry off Evidence: ledger:E0316</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26758" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x129" flags="0x30">
    <title>Injection Timing (main pulse) - Coolant Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. End-of-injection angle term for the main injection pulse by coolant, in crank degrees of the 720 degree cycle. The coolant term and the engine speed term are added and capped at 720 deg. Stock 514 deg at every coolant temperature. Effect: raise = main injection pulse ends later in the engine cycle Evidence: ledger:E0317, ledger:E1182</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x260C6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg (crank, end of injection)</units>
      <decimalpl>2</decimalpl>
      <min>-1024.000000</min>
      <max>1023.968750</max>
      <MATH equation="X/32"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x12A" flags="0x30">
    <title>Injection Timing (main pulse) - RPM Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. End-of-injection angle term for the main injection pulse by engine speed, in crank degrees of the 720 degree cycle. The coolant term and the engine speed term are added and capped at 720 deg. Stock 120 deg at 0 and 128 rpm, 90 deg at 256 rpm, 40 at 384, 20 at 512 and 0 from 640 rpm: it only acts while cranking. Effect: raise = main injection pulse ends later in the engine cycle Evidence: ledger:E0317, ledger:E1182</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="128" />
      <LABEL index="2" value="256" />
      <LABEL index="3" value="384" />
      <LABEL index="4" value="512" />
      <LABEL index="5" value="640" />
      <LABEL index="6" value="768" />
      <LABEL index="7" value="896" />
      <LABEL index="8" value="1024" />
      <LABEL index="9" value="1152" />
      <LABEL index="10" value="1280" />
      <LABEL index="11" value="1408" />
      <LABEL index="12" value="1536" />
      <LABEL index="13" value="1664" />
      <LABEL index="14" value="1792" />
      <LABEL index="15" value="1920" />
      <LABEL index="16" value="2048" />
      <LABEL index="17" value="2176" />
      <LABEL index="18" value="2304" />
      <LABEL index="19" value="2432" />
      <LABEL index="20" value="2560" />
      <LABEL index="21" value="2688" />
      <LABEL index="22" value="2816" />
      <LABEL index="23" value="2944" />
      <LABEL index="24" value="3072" />
      <LABEL index="25" value="3200" />
      <LABEL index="26" value="3328" />
      <LABEL index="27" value="3456" />
      <LABEL index="28" value="3584" />
      <LABEL index="29" value="3712" />
      <LABEL index="30" value="3840" />
      <LABEL index="31" value="3968" />
      <LABEL index="32" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x260EA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg (crank, end of injection)</units>
      <decimalpl>2</decimalpl>
      <min>-1024.000000</min>
      <max>1023.968750</max>
      <MATH equation="X/32"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x12B" flags="0x30">
    <title>Injection Timing (second pulse) - Coolant Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. End-of-injection angle term for the second injection pulse by coolant, in crank degrees of the 720 degree cycle. The coolant term and the engine speed term are added and capped at 720 deg. Stock 0 everywhere. Effect: raise = second injection pulse ends later in the engine cycle Evidence: ledger:E0317, ledger:E1182</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2612E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg (crank, end of injection)</units>
      <decimalpl>2</decimalpl>
      <min>-1024.000000</min>
      <max>1023.968750</max>
      <MATH equation="X/32"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x12C" flags="0x30">
    <title>Cranking Dwell Multiplier vs Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While cranking, the dwell from the base dwell table and modifier is multiplied by this, by battery voltage. Stock 1.0 everywhere. Effect: raise = longer coil charge while cranking (hotter spark, more coil heat) Evidence: ledger:E0318</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>22</indexcount>
      <units>V</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="4.5" />
      <LABEL index="1" value="5.5" />
      <LABEL index="2" value="6.5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="8.5" />
      <LABEL index="5" value="9.5" />
      <LABEL index="6" value="10.5" />
      <LABEL index="7" value="11.5" />
      <LABEL index="8" value="12.5" />
      <LABEL index="9" value="13.5" />
      <LABEL index="10" value="14.5" />
      <LABEL index="11" value="15.5" />
      <LABEL index="12" value="16.5" />
      <LABEL index="13" value="17.5" />
      <LABEL index="14" value="18.5" />
      <LABEL index="15" value="19.5" />
      <LABEL index="16" value="20.5" />
      <LABEL index="17" value="21.5" />
      <LABEL index="18" value="22.5" />
      <LABEL index="19" value="23.5" />
      <LABEL index="20" value="24.5" />
      <LABEL index="21" value="25.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2FA8A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="22" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x12D" flags="0x0">
    <title>Cranking Maximum Dwell Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While cranking, the maximum allowed dwell is the cranking dwell times this. Stock 1.20. Effect: sets how far cranking dwell may stretch or shrink Evidence: ledger:E0318</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2FAB8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x12E" flags="0x0">
    <title>Cranking Minimum Dwell Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While cranking, the minimum dwell is the cranking dwell times this (further limited by the dwell ceiling). Stock 0.75. Effect: sets how far cranking dwell may stretch or shrink Evidence: ledger:E0318</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2FAB6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x12F" flags="0x0">
    <title>Final Drive Ratio - Transmission Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The transmission&#x27;s own copy of the axle ratio (stock 4.5555 = 41/9). Shift points and converter lockup use a vehicle speed computed from this and Tire Revs per Distance - Transmission Speed, not from Final Drive Ratio. After an axle or tire change set both pairs, or the speedometer will be right and the shift points off (E0319). Change it together with Final Drive Ratio and VSS Tire Revs per Distance: this pair is what shift points and converter lockup use. Code-proven, not yet confirmed on a drive. Effect: shift points and converter lockup speed (transmission-side vehicle speed) Evidence: ledger:E0319, ledger:E0808</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3DF1E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>:1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x130" flags="0x0">
    <title>Tire Revs per Distance - Transmission Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The transmission&#x27;s own tire size (stored as revs/km x64). Stock 639.4 revs/mi, about 1.8 % more than the speedometer&#x27;s 627.6, so the transmission sees speed about 1.8 % lower than the dash. Shift points and converter lockup follow this value, not VSS Tire Revs per Distance. Set both after a tire change (E0319). Change it together with Final Drive Ratio and VSS Tire Revs per Distance: this pair is what shift points and converter lockup use. Code-proven, not yet confirmed on a drive. Effect: shift points and converter lockup speed (transmission-side vehicle speed) Evidence: ledger:E0319, ledger:E0808</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3DF42" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>revs/mi</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>1647.943110</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*0.02514600"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x131" flags="0x0">
    <title>Idle Speed Control - A/C Airflow Offset Ramp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the A/C is requested, the idle speed controller&#x27;s airflow limits are raised toward the A/C idle air term by this much per update. Stock 0.10 g/s. Effect: raise = limits follow the A/C air sooner Evidence: ledger:E0322</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x223FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s per update</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x132" flags="0x30">
    <title>Idle Speed Control - Controller Coefficients (In Gear) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Eight coefficients of the idle speed controller used in gear (stock identical to the Park / Neutral set). Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (idle speed controller) Evidence: ledger:E0322, ledger:E0899</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>coefficient</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x223FE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x133" flags="0x30">
    <title>Idle Speed Control - Controller Coefficients (Park / Neutral) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Eight coefficients of the idle speed controller used in Park / Neutral (stock identical to the in-gear set). Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (idle speed controller) Evidence: ledger:E0322, ledger:E0899</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>coefficient</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2240E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x134" flags="0x0">
    <title>RPM Limiter - Catalyst Hot Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this modelled catalyst temperature (and above the cut rpm) the ETC request is limited to its minimum to bring rpm down. Stock 800 C. Effect: raise = the catalyst-hot rpm cut needs a hotter catalyst Evidence: ledger:E0325</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x23C86" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x135" flags="0x0">
    <title>RPM Limiter - Catalyst Hot Cut RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With the catalyst hot, rpm above this starts the cut. Stock 3500 rpm. Effect: raise = cut starts at higher rpm Evidence: ledger:E0325</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x23C76" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x136" flags="0x0">
    <title>RPM Limiter - Catalyst Hot Cut Hold RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once started, the cut holds while rpm stays above this. Stock 3000 rpm. Effect: keep below the cut rpm Evidence: ledger:E0325</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x23C78" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x137" flags="0x0">
    <title>RPM Limiter - Engage RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The limiter / rpm control block becomes active once rpm exceeds this (when its enable flags are set). Stock 1100 rpm. Effect: raise = block engages at higher rpm Evidence: ledger:E0325</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x23C7A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x138" flags="0x0">
    <title>RPM Limiter - Release RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this rpm the limit is released (no limit). Stock 600 rpm. Effect: keep below idle Evidence: ledger:E0325</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x23C80" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x139" flags="0x0">
    <title>RPM Limiter - Release RPM (after release)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Release threshold used once released, for hysteresis. Stock 650 rpm. Effect: keep above the release rpm Evidence: ledger:E0325</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x23C7E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x13A" flags="0x0">
    <title>RPM Control - Minimum Target RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The rpm controller&#x27;s target is the desired idle or this, whichever is higher. Stock 900 rpm. Effect: raise = higher minimum target Evidence: ledger:E0325</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x23C7C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x13B" flags="0x0">
    <title>RPM Control - Maximum Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The rpm controller only runs below this vehicle speed. Stock 10 km/h. Effect: raise = runs at higher speeds Evidence: ledger:E0325</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x23C90" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x13C" flags="0x30">
    <title>Pedal Throttle Area - Rise Rate Limit vs RPM by Trans State</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most the pedal throttle-area demand may increase per update, by transmission state (rows) and rpm (columns). Softens tip-in. Rows: 0 to 3 = 1st to 4th gear (4 and 5 unused on the 4-speed), 6 = Neutral, 7 = Reverse, 8 = Park. Effect: raise = sharper throttle response on tip-in Evidence: ledger:E0330, ledger:E1329</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>8</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 7" />
      <LABEL index="1" value="state 0 (1st)" />
      <LABEL index="2" value="state 1 (2nd)" />
      <LABEL index="3" value="state 2 (3rd)" />
      <LABEL index="4" value="state 3 (4th)" />
      <LABEL index="5" value="state 4" />
      <LABEL index="6" value="state 5" />
      <LABEL index="7" value="other (P / N)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24C12" mmedelementsizebits="16" mmedrowcount="8" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% area per update</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x13D" flags="0x30">
    <title>Pedal Throttle Area - Fall Rate Limit vs RPM by Trans State</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most the pedal throttle-area demand may decrease per update, by transmission state (rows) and rpm (columns). Softens tip-out. Rows: 0 to 3 = 1st to 4th gear (4 and 5 unused on the 4-speed), 6 = Neutral, 7 = Reverse, 8 = Park. Effect: raise = throttle closes faster on tip-out Evidence: ledger:E0330, ledger:E1329</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>8</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 7" />
      <LABEL index="1" value="state 0 (1st)" />
      <LABEL index="2" value="state 1 (2nd)" />
      <LABEL index="3" value="state 2 (3rd)" />
      <LABEL index="4" value="state 3 (4th)" />
      <LABEL index="5" value="state 4" />
      <LABEL index="6" value="state 5" />
      <LABEL index="7" value="other (P / N)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24BB2" mmedelementsizebits="16" mmedrowcount="8" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% area per update</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x13E" flags="0x30">
    <title>Cold Engine Forced Upshift Speed - 1st</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold engine: when vehicle speed (transmission side) reaches this value in 1st gear, the PCM commands the next gear up. Stock 27.7 to 37.9 mph. Only active while corrected coolant is below 32 C (Cold Engine Shift Limits - Coolant Below) (E0331). Effect: cold-engine shift speed Evidence: ledger:E0331, ledger:E0725</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (corrected coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x394F0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x13F" flags="0x30">
    <title>Cold Engine Forced Upshift Speed - 2nd</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold engine: when vehicle speed (transmission side) reaches this value in 2nd gear, the PCM commands the next gear up. Stock 53.7 to 75.8 mph. Only active while corrected coolant is below 32 C (Cold Engine Shift Limits - Coolant Below) (E0331). Effect: cold-engine shift speed Evidence: ledger:E0331, ledger:E0725</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (corrected coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39504" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x140" flags="0x30">
    <title>Cold Engine Forced Upshift Speed - 3rd</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold engine: when vehicle speed (transmission side) reaches this value in 3rd gear, the PCM commands the next gear up. Stock 310.7 mph, i.e. off. Only active while corrected coolant is below 32 C (Cold Engine Shift Limits - Coolant Below) (E0331). Effect: cold-engine shift speed Evidence: ledger:E0331, ledger:E0725</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (corrected coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39518" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x141" flags="0x30">
    <title>Cold Engine Downshift Inhibit Speed - 2-1</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold engine: while a 2-1 downshift is pending, it is held off whenever vehicle speed is at or above this value. Stock 25.2 to 32.6 mph. Only active while corrected coolant is below 32 C (Cold Engine Shift Limits - Coolant Below) (E0331). Effect: cold-engine shift speed Evidence: ledger:E0331, ledger:E0725</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (corrected coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3952E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x142" flags="0x30">
    <title>Cold Engine Downshift Inhibit Speed - 3-2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold engine: while a 3-2 downshift is pending, it is held off whenever vehicle speed is at or above this value. Stock 50.6 to 63.1 mph. Only active while corrected coolant is below 32 C (Cold Engine Shift Limits - Coolant Below) (E0331). Effect: cold-engine shift speed Evidence: ledger:E0331, ledger:E0725</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (corrected coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39542" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x143" flags="0x30">
    <title>Cold Engine Downshift Inhibit Speed - 4-3</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold engine: while a 4-3 downshift is pending, it is held off whenever vehicle speed is at or above this value. Stock 307.6 mph, i.e. off. Only active while corrected coolant is below 32 C (Cold Engine Shift Limits - Coolant Below) (E0331). Effect: cold-engine shift speed Evidence: ledger:E0331, ledger:E0725</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (corrected coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39556" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x144" flags="0x0">
    <title>Cold Engine Shift Limits - Coolant Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cold-engine shift speed limits (the cold forced-upshift and downshift-inhibit speed curves) apply while engine coolant is below this temperature. Stock 32 C. Effect: raise = the cold shift limits stay in force until the engine is warmer Evidence: ledger:E0331, ledger:E0725, ledger:E0791</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3952A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x145" flags="0x30">
    <title>ETC Torque Control - Gain Switch Torque by Trans State</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. INACTIVE on the stock H3: the controller only runs when an enable = 1 (stock 0). Engine torque at which the throttle torque controller switches from its low-torque to its high-torque gains, per transmission state. Stock 150 / 140 / 135 / 120 Nm for states 0 to 3, 100 Nm above. Effect: raise = low-torque gains used up to higher torque Evidence: ledger:E0333, ledger:E0341</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20A56" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>16383.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x146" flags="0x0">
    <title>ETC Torque Control - Gain Switch Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. INACTIVE on the stock H3: the controller only runs when an enable = 1 (stock 0). Once on the high-torque gains, the switch torque is lowered by half of this. Stock 10 Nm (5 Nm effective). Effect: raise = less switching back and forth Evidence: ledger:E0333, ledger:E0341</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20A50" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>16383.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x147" flags="0x30">
    <title>ETC Torque Control - Input Gain (high torque) vs RPM by Trans State (dormant)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, high engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): the controller&#x27;s input is multiplied by this (1.0 = unchanged). 1.0 = 65536 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:E0390, ledger:E1149</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20A6C" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x148" flags="0x30">
    <title>ETC Torque Control - Output Feedback Gain (high torque) vs RPM by Trans State (dormant)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, high engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): share of the controller&#x27;s previous output carried into the new output each update. 1.0 = 65536 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:E0390, ledger:E1149</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20CFC" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x149" flags="0x30">
    <title>ETC Torque Control - Previous Input Weight (high torque) vs RPM by Trans State (dormant)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, high engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): weight of the previous scaled input in the new output (signed). 1.0 = 8192 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:E0390, ledger:E1149</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20F8C" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>-4.000000</min>
      <max>3.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x14A" flags="0x30">
    <title>ETC Torque Control - Current Input Weight (high torque) vs RPM by Trans State (dormant)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, high engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): weight of the current scaled input in the new output (signed). 1.0 = 8192 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:E0390, ledger:E1149</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2121C" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>-4.000000</min>
      <max>3.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x14B" flags="0x30">
    <title>ETC Torque Control - Input Gain (low torque) vs RPM by Trans State (dormant)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, low engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): the controller&#x27;s input is multiplied by this (1.0 = unchanged). 1.0 = 65536 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:E0390, ledger:E1149</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20BB4" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x14C" flags="0x30">
    <title>ETC Torque Control - Output Feedback Gain (low torque) vs RPM by Trans State (dormant)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, low engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): share of the controller&#x27;s previous output carried into the new output each update. 1.0 = 65536 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:E0390, ledger:E1149</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20E44" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x14D" flags="0x30">
    <title>ETC Torque Control - Previous Input Weight (low torque) vs RPM by Trans State (dormant)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, low engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): weight of the previous scaled input in the new output (signed). 1.0 = 8192 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:E0390, ledger:E1149</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x210D4" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>-4.000000</min>
      <max>3.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x14E" flags="0x30">
    <title>ETC Torque Control - Current Input Weight (low torque) vs RPM by Trans State (dormant)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, low engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): weight of the current scaled input in the new output (signed). 1.0 = 8192 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:E0390, ledger:E1149</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21364" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>-4.000000</min>
      <max>3.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x14F" flags="0x0">
    <title>2-1 Downshift Pressure Control - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = use the 2-1 downshift pressure tables during a 2-1 downshift, 0 = never (normal shift pressure throughout). Stock 1. Active only during a 2-1 downshift (from 2nd with a downshift commanded, until it leaves 2nd); replaces the normal shift pressure (E0334). Effect: turns 2-1 downshift pressure control on or off Evidence: ledger:E0334</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x375CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0/1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x150" flags="0x30">
    <title>Engine Torque Map for Trans Torque Estimate (fraction of max)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Reference only. The transmission&#x27;s model of engine torque by throttle demand and rpm, as a percentage of maximum. It feeds the transmission&#x27;s torque estimate (times converter torque ratio and gear ratio) and its engine-speed predictor. Stock 0 at closed throttle, about 84 to 100 % at wide open. Changing it changes shift and line-pressure behaviour without changing the engine (E0336). Relative unit: the transmission&#x27;s torque model is scaled to its own full-scale engine torque, not to Nm (E0722). Effect: transmission torque estimate (shift pressure, shift timing) Evidence: ledger:E0336, ledger:E0722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>% throttle demand</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E44E" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% of full scale</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x151" flags="0x30">
    <title>Torque Converter Torque Ratio vs Speed Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Reference only. The transmission&#x27;s model of torque converter multiplication: 2.06 at stall (speed ratio 0) falling to 1.00 once the converter couples (speed ratio 0.94 and above). Used in the transmission torque estimate. Change it only to match a different converter (E0336). Effect: transmission torque estimate Evidence: ledger:E0336</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>speed ratio (turbine / engine)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.000" />
      <LABEL index="1" value="0.062" />
      <LABEL index="2" value="0.125" />
      <LABEL index="3" value="0.188" />
      <LABEL index="4" value="0.250" />
      <LABEL index="5" value="0.312" />
      <LABEL index="6" value="0.375" />
      <LABEL index="7" value="0.438" />
      <LABEL index="8" value="0.500" />
      <LABEL index="9" value="0.562" />
      <LABEL index="10" value="0.625" />
      <LABEL index="11" value="0.688" />
      <LABEL index="12" value="0.750" />
      <LABEL index="13" value="0.812" />
      <LABEL index="14" value="0.875" />
      <LABEL index="15" value="0.938" />
      <LABEL index="16" value="1.000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E6AE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>:1</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x152" flags="0x30">
    <title>Transmission Gear Ratios (1st-4th), second copy</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A second copy of the 4L60-E gear ratios (stock 3.06 / 1.63 / 1.00 / 0.70), used by the transmission torque estimate. For a gearbox with other ratios change this and Transmission Gear Ratios (1st-4th) together (E0337). Effect: transmission torque estimate Evidence: ledger:E0337</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E9AE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>:1</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>31.999512</max>
      <MATH equation="X/2048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x153" flags="0x30">
    <title>Garage Shift Pressure Adder - Into Drive, vs Speed vs Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra engagement pressure when shifting from Park/Neutral (or Reverse) into a forward range, by vehicle speed and throttle. Stock 0 to 65 psi. Added to the 600 kPa garage base pressure; the sum is used when it is above normal line pressure. Pressure scale from the code (kPa x16); the PID documentation disagrees, so treat the psi values as provisional (E0338). Effect: Drive engagement firmness Evidence: ledger:E0338, ledger:E0713, ledger:E0931</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>% throttle demand</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>mph</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="3.1" />
      <LABEL index="2" value="6.2" />
      <LABEL index="3" value="9.3" />
      <LABEL index="4" value="12.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37DC9" mmedelementsizebits="8" mmedrowcount="5" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>psi</units>
      <decimalpl>2</decimalpl>
      <min>-148.518656</min>
      <max>147.358354</max>
      <MATH equation="X*1.160302"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x154" flags="0x30">
    <title>Garage Shift Pressure Adder - Into Reverse, vs Speed vs Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra engagement pressure when shifting into Reverse, by vehicle speed and throttle. Stock 0 to 45 psi. Added to the 600 kPa garage base pressure; the sum is used when it is above normal line pressure. Pressure scale from the code (kPa x16); the PID documentation disagrees, so treat the psi values as provisional (E0338). Effect: Reverse engagement firmness Evidence: ledger:E0338, ledger:E0713, ledger:E0931</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>% throttle demand</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>mph</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="3.1" />
      <LABEL index="2" value="6.2" />
      <LABEL index="3" value="9.3" />
      <LABEL index="4" value="12.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37DF9" mmedelementsizebits="8" mmedrowcount="5" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>psi</units>
      <decimalpl>2</decimalpl>
      <min>-148.518656</min>
      <max>147.358354</max>
      <MATH equation="X*1.160302"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x155" flags="0x30">
    <title>Garage Shift Pressure vs Trans Temp vs RPM - Into Drive (A)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engagement pressure adder into a forward range, timer below the P/N dwell threshold (mode 1; also used alone in mode 5), by transmission fluid temperature and engine rpm. Stock 0 to 44 psi. Added to the 600 kPa garage base pressure; the sum is used when it is above normal line pressure. Pressure scale from the code (kPa x16); the PID documentation disagrees, so treat the psi values as provisional (E0338). Effect: engagement firmness Evidence: ledger:E0338, ledger:E0713</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="512" />
      <LABEL index="1" value="640" />
      <LABEL index="2" value="768" />
      <LABEL index="3" value="896" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1152" />
      <LABEL index="6" value="1280" />
      <LABEL index="7" value="1408" />
      <LABEL index="8" value="1536" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x38196" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>9</indexcount>
      <units>degC (trans fluid)</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37EEB" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>psi</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>147.938505</max>
      <MATH equation="X*0.580151"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x156" flags="0x30">
    <title>Garage Shift Pressure vs Trans Temp vs RPM - Into Drive (B)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engagement pressure adder into a forward range, timer above the P/N dwell threshold (mode 2), by transmission fluid temperature and engine rpm. Stock 0 to 44 psi. Added to the 600 kPa garage base pressure; the sum is used when it is above normal line pressure. Pressure scale from the code (kPa x16); the PID documentation disagrees, so treat the psi values as provisional (E0338). Effect: engagement firmness Evidence: ledger:E0338, ledger:E0713</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="512" />
      <LABEL index="1" value="640" />
      <LABEL index="2" value="768" />
      <LABEL index="3" value="896" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1152" />
      <LABEL index="6" value="1280" />
      <LABEL index="7" value="1408" />
      <LABEL index="8" value="1536" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x38196" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>9</indexcount>
      <units>degC (trans fluid)</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37FFB" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>psi</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>147.938505</max>
      <MATH equation="X*0.580151"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x157" flags="0x30">
    <title>Garage Shift Pressure vs Trans Temp vs RPM - Into Reverse (A)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engagement pressure adder into Reverse, timer below the P/N dwell threshold (mode 3), by transmission fluid temperature and engine rpm. Stock 0 to 44 psi. Added to the 600 kPa garage base pressure; the sum is used when it is above normal line pressure. Pressure scale from the code (kPa x16); the PID documentation disagrees, so treat the psi values as provisional (E0338). Effect: engagement firmness Evidence: ledger:E0338, ledger:E0713</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="512" />
      <LABEL index="1" value="640" />
      <LABEL index="2" value="768" />
      <LABEL index="3" value="896" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1152" />
      <LABEL index="6" value="1280" />
      <LABEL index="7" value="1408" />
      <LABEL index="8" value="1536" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x38196" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>9</indexcount>
      <units>degC (trans fluid)</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37F4B" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>psi</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>147.938505</max>
      <MATH equation="X*0.580151"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x158" flags="0x30">
    <title>Garage Shift Pressure vs Trans Temp vs RPM - Into Reverse (B)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engagement pressure adder into Reverse, timer above the P/N dwell threshold (mode 4), by transmission fluid temperature and engine rpm. Stock 0 to 44 psi. Added to the 600 kPa garage base pressure; the sum is used when it is above normal line pressure. Pressure scale from the code (kPa x16); the PID documentation disagrees, so treat the psi values as provisional (E0338). Effect: engagement firmness Evidence: ledger:E0338, ledger:E0713</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="512" />
      <LABEL index="1" value="640" />
      <LABEL index="2" value="768" />
      <LABEL index="3" value="896" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1152" />
      <LABEL index="6" value="1280" />
      <LABEL index="7" value="1408" />
      <LABEL index="8" value="1536" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x38196" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>9</indexcount>
      <units>degC (trans fluid)</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38053" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>psi</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>147.938505</max>
      <MATH equation="X*0.580151"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x159" flags="0x0">
    <title>Garage Shift Base Pressure - Into Drive</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base line pressure for a garage shift into a forward range (modes 1 and 2); the table adders are added to it and the sum is used when it is above normal line pressure. Stock 87.0 psi (600 kPa) (E0338). Effect: engagement firmness Evidence: ledger:E0338</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E234" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>psi</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>594.066911</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*0.00906488"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x15A" flags="0x0">
    <title>Garage Shift Base Pressure - Into Reverse</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base line pressure for a garage shift into Reverse (modes 3 and 4); the table adders are added to it and the sum is used when it is above normal line pressure. Stock 87.0 psi (600 kPa) (E0338). Effect: engagement firmness Evidence: ledger:E0338</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E238" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>psi</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>594.066911</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*0.00906488"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x15B" flags="0x0">
    <title>Garage Shift Base Pressure - Low-Speed Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base line pressure for a garage shift into the low-speed special mode 5; the table adders are added to it and the sum is used when it is above normal line pressure. Stock 87.0 psi (600 kPa) (E0338). Effect: engagement firmness Evidence: ledger:E0338</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E236" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>psi</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>594.066911</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*0.00906488"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x15C" flags="0x30">
    <title>Trans Fluid Temp Sensor - Temperature Points</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Temperature at each of the 33 sensor resistance points (stock 150 C down to -40 C in 5.9 C steps); the PCM interpolates between them to get transmission fluid temperature (PID 1940) (E0342). Effect: reported and used transmission fluid temperature Evidence: ledger:E0342</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DE6C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x15D" flags="0x0">
    <title>Trans Hot Mode - Enter Above (fluid temp)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot mode starts when transmission fluid temperature rises above this. Stock 130.0 C (266 F). Hot mode switches the transmission to its hot shift and converter-lockup schedules. (E0343). Effect: transmission hot mode Evidence: ledger:E0343</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DD2E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x15E" flags="0x0">
    <title>Trans Hot Mode - Leave Below (fluid temp)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot mode ends when fluid temperature is back below this and the minimum hot time has passed. Stock 123.0 C (253 F). Hot mode switches the transmission to its hot shift and converter-lockup schedules. (E0343). Effect: transmission hot mode Evidence: ledger:E0343</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DD30" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x15F" flags="0x0">
    <title>Trans Hot Mode - Minimum Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once in hot mode the transmission stays in it at least this long. Stock 150 s. Hot mode switches the transmission to its hot shift and converter-lockup schedules. (E0343). Effect: transmission hot mode Evidence: ledger:E0343</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DD3A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x160" flags="0x0">
    <title>Trans Hot Mode - Enable (fluid temp)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = enter hot mode on fluid temperature (sensor OK). Stock 1. Hot mode switches the transmission to its hot shift and converter-lockup schedules. (E0343). Effect: transmission hot mode Evidence: ledger:E0343</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DDDA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0/1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x161" flags="0x0">
    <title>Trans Hot Mode - Enter Above (sensor fault)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot mode entry used while the fluid temperature sensor is faulted and a substitute temperature is used. Stock 115.0 C. Hot mode switches the transmission to its hot shift and converter-lockup schedules. (E0343). The sensor fault handling also runs while the transmission range switch reading is invalid. Effect: transmission hot mode Evidence: ledger:E0343, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DD32" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x162" flags="0x0">
    <title>Trans Hot Mode - Leave Below (sensor fault)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot mode exit used while the fluid temperature sensor is faulted. Stock 110.0 C. Hot mode switches the transmission to its hot shift and converter-lockup schedules. (E0343). The sensor fault handling also runs while the transmission range switch reading is invalid. Effect: transmission hot mode Evidence: ledger:E0343, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DD34" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x163" flags="0x30">
    <title>Torque-Based Upshift Inhibit - Enable by Shift Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = the upshift inhibit runs in that shift mode. Stock on in modes 3, 6 and 10. Part of the torque-based upshift inhibit: an upshift is held off when the torque predicted after it would be below what the truck needs now. Effect: whether upshifts can be held for lack of torque Evidence: ledger:E0345</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>shift mode</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39108" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>0/1</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x164" flags="0x30">
    <title>Upshift Inhibit - Expected Throttle vs Speed (mode 6)</title>
    <description>Change in small steps and log. Each row is a 1-D curve [COUNT = 17][17 points]; COUNT is a structure word, never edit it (E0345). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The throttle the predictor assumes the driver will hold after an upshift, by vehicle speed and current gear, in shift mode 6. Stock 100 % in 1st and 4th; 2nd and 3rd dip to 25..37 % at mid speeds. Lower = the truck is assumed to need less torque, so upshifts are held less often. Part of the torque-based upshift inhibit: an upshift is held off when the torque predicted after it would be below what the truck needs now (E0345). Effect: how readily upshifts are held under load Evidence: ledger:E0345</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0.0" />
      <LABEL index="2" value="6.2" />
      <LABEL index="3" value="12.4" />
      <LABEL index="4" value="18.6" />
      <LABEL index="5" value="24.9" />
      <LABEL index="6" value="31.1" />
      <LABEL index="7" value="37.3" />
      <LABEL index="8" value="43.5" />
      <LABEL index="9" value="49.7" />
      <LABEL index="10" value="55.9" />
      <LABEL index="11" value="62.1" />
      <LABEL index="12" value="68.4" />
      <LABEL index="13" value="74.6" />
      <LABEL index="14" value="80.8" />
      <LABEL index="15" value="87.0" />
      <LABEL index="16" value="93.2" />
      <LABEL index="17" value="99.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>current gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x391C8" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle demand</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x165" flags="0x30">
    <title>Upshift Inhibit - Expected Throttle vs Speed (other modes)</title>
    <description>Change in small steps and log. Each row is a 1-D curve [COUNT = 17][17 points]; COUNT is a structure word, never edit it (E0345). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The throttle the predictor assumes the driver will hold after an upshift, by vehicle speed and current gear, in shift modes other than 6 and 8. Stock 100 % in 1st and 4th; 2nd and 3rd dip to 25..37 % at mid speeds. Lower = the truck is assumed to need less torque, so upshifts are held less often. Part of the torque-based upshift inhibit: an upshift is held off when the torque predicted after it would be below what the truck needs now (E0345). Effect: how readily upshifts are held under load Evidence: ledger:E0345</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0.0" />
      <LABEL index="2" value="6.2" />
      <LABEL index="3" value="12.4" />
      <LABEL index="4" value="18.6" />
      <LABEL index="5" value="24.9" />
      <LABEL index="6" value="31.1" />
      <LABEL index="7" value="37.3" />
      <LABEL index="8" value="43.5" />
      <LABEL index="9" value="49.7" />
      <LABEL index="10" value="55.9" />
      <LABEL index="11" value="62.1" />
      <LABEL index="12" value="68.4" />
      <LABEL index="13" value="74.6" />
      <LABEL index="14" value="80.8" />
      <LABEL index="15" value="87.0" />
      <LABEL index="16" value="93.2" />
      <LABEL index="17" value="99.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>current gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x392E8" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle demand</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x166" flags="0x30">
    <title>Upshift Inhibit - Speed Ratio Curve (predictor step 1) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Predictor step 1: converts the current converter speed ratio into an intermediate value that the per-gear factor scales next. Part of the torque-based upshift inhibit: an upshift is held off when the torque predicted after it would be below what the truck needs now. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (upshift inhibit predictor) Evidence: ledger:E0345, ledger:E0899</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x39136" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>speed ratio (turbine / engine)</units>
      <embedinfo type="1" />
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3917E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x167" flags="0x30">
    <title>Upshift Inhibit - Per-Gear Factor (predictor step 2)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Predictor step 2: carries the converter value of the current speed ratio over to the next gear, per current gear. Stock (next gear ratio / current gear ratio) to the power 1.5: 0.387 / 0.483 / 0.581 for 1st / 2nd / 3rd. Part of the torque-based upshift inhibit: an upshift is held off when the torque predicted after it would be below what the truck needs now. Effect: predicted speed ratio after an upshift Evidence: ledger:E0345, ledger:E1028, ledger:E1473</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>current gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3912E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x168" flags="0x30">
    <title>Upshift Inhibit - Predicted Speed Ratio (predictor step 3)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Predictor step 3: the converter speed ratio expected in the next gear (stock 0.34 to 0.98), by the step 2 value, at the Upshift Inhibit Predictor Value Breakpoints. Part of the torque-based upshift inhibit: an upshift is held off when the torque predicted after it would be below what the truck needs now. Effect: predicted speed ratio after an upshift Evidence: ledger:E0345, ledger:E1473</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3915A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>predictor value (raw, as the Speed Ratio Curve output)</units>
      <embedinfo type="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x391A2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>speed ratio</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x169" flags="0x30">
    <title>Tip-In Torque Mgmt - Minimum Speed by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only, closed-throttle tip-ins): active only above this vehicle speed. Stock 5 km/h. Effect: widens or narrows the speed range where tip-ins are softened Evidence: ledger:E0346</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2150C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x16A" flags="0x30">
    <title>Tip-In Torque Mgmt - Maximum Speed by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only, closed-throttle tip-ins): active only below this vehicle speed. Stock 64 km/h. Effect: widens or narrows the speed range where tip-ins are softened Evidence: ledger:E0346</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21500" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x16B" flags="0x0">
    <title>Tip-In Torque Mgmt - Closed Throttle Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only, closed-throttle tip-ins): throttle counts as closed below this. Stock 0.38 %. Effect: raise = counts as closed with slightly open throttle Evidence: ledger:E0346</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21530" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x16C" flags="0x0">
    <title>Tip-In Torque Mgmt - Closed Throttle Ends Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only, closed-throttle tip-ins): the closed-throttle flag clears at this. Stock 0.47 %. Effect: keep above the closed value Evidence: ledger:E0346</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2152E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x16D" flags="0x0">
    <title>Tip-In Torque Mgmt - Minimum Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only, closed-throttle tip-ins): only above this coolant temperature. Stock 75 C. Effect: lower = also when colder Evidence: ledger:E0346</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21532" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x16E" flags="0x0">
    <title>Idle Airflow Learn - Stored Copy Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. Upper clamp on the filtered copy of the learned idle airflow kept in keep-alive memory. Stock 3.5 g/s. Effect: raise = the stored learn can hold more air Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x16F" flags="0x0">
    <title>Idle Airflow Learn - Stored Copy Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. Lower clamp on the filtered stored copy. Stock 0. Effect: lower = the stored learn can take air away Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x170" flags="0x0">
    <title>Idle Airflow Learn - Saved Value Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. Upper clamp applied when the learn is written to keep-alive memory. Stock 3.5 g/s. Effect: raise = a larger learned value survives key-off Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x171" flags="0x0">
    <title>Idle Airflow Learn - Saved Value Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. Lower clamp applied when the learn is written to keep-alive memory. Stock -1.0 g/s. Effect: lower = a more negative learned value survives key-off Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x172" flags="0x0">
    <title>Idle Airflow Learn - Stored Copy Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. How fast the stored copy follows the learned value each update (first-order filter). Stock 0.01. Effect: raise = the stored learn tracks changes faster Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291F8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x173" flags="0x0">
    <title>Idle Airflow Learn - Restore Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. How fast the working learned value is pulled toward the stored copy when the truck is moving above the speed and rpm limits. Stock 0.1; the stock speed limit is 255 km/h, so on stock it never runs. Effect: raise = faster pull back to the stored value Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x174" flags="0x0">
    <title>Idle Airflow Learn - Filter Enable Run Time (learn below stored)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. The stored copy is only filtered after the engine has run this long, when the new learn is at or below the stored copy. Stock 90 s. Effect: raise = later learning after a start Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29208" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x175" flags="0x0">
    <title>Idle Airflow Learn - Filter Enable Run Time (learn above stored)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. As the other run-time gate, when the new learn is above the stored copy. Stock 90 s. Effect: raise = later learning after a start Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2920A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x176" flags="0x0">
    <title>Idle Airflow Learn - Filter Minimum Idle-Mode Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. Minimum time in the idle-control timer before the stored copy is filtered. Stock 5 s. Effect: raise = only long idles update the stored learn Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2920C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x177" flags="0x0">
    <title>Idle Airflow Learn - Capture Minimum Idle-Mode Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. Minimum time in the idle-control timer before a new learned value is captured. Stock 30 s. Effect: raise = only long idles capture a new learn Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2920E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x178" flags="0x0">
    <title>Idle Airflow Learn - Capture Stable-State Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. The trans-state and A/C state must be unchanged this long before a capture. Stock 2 s. Effect: raise = more settling before a capture Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29206" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x179" flags="0x0">
    <title>Idle Airflow Learn - Filter Stable-State Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. The same stable-state timer, for the stored-copy filter. Stock 1 s. Effect: raise = more settling before filtering Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29204" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x17A" flags="0x0">
    <title>Idle Airflow Learn - Filter Maximum Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. The stored copy is only filtered below this vehicle speed. Stock 2 km/h. Effect: raise = learning while creeping Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29202" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x17B" flags="0x0">
    <title>Altitude/Cold Idle-Up - Hold Maximum Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up flare and altitude idle-up gating. The altitude/cold idle-up (stock amount 0) is held while vehicle speed is below this. Stock 8 km/h. Effect: affects only a non-zero idle-up amount Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A5A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x17C" flags="0x0">
    <title>Altitude/Cold Idle-Up - Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up flare and altitude idle-up gating. How long the altitude/cold idle-up is held (timer in 1/20 s). Stock 30 s. Effect: raise = idle-up lasts longer Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A5A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x17D" flags="0x0">
    <title>Altitude/Cold Idle-Up - Baro Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up flare and altitude idle-up gating. The idle-up applies when barometric pressure is below this. Stock 80 kPa. Effect: raise = applies at lower altitude Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A594" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x17E" flags="0x0">
    <title>Start-Up RPM Flare - Cancel After Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up flare and altitude idle-up gating. After this run time the start-up flare is cancelled as soon as the truck moves or the throttle opens. Stock 8 s. Effect: raise = the flare survives an early drive-away longer Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A5AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x17F" flags="0x0">
    <title>Start-Up RPM Flare - Cancel Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up flare and altitude idle-up gating. Vehicle speed above which the flare is cancelled (after the cancel run time). Stock 30 km/h. Effect: raise = flare kept to a higher speed Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A5A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x180" flags="0x0">
    <title>Start-Up RPM Flare - Cancel Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up flare and altitude idle-up gating. Throttle above which the flare is cancelled (after the cancel run time). Stock 5 %. Effect: raise = flare kept with more throttle Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A596" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x181" flags="0x0">
    <title>Idle RPM-Control Mode - Maximum Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle rpm-control mode entry. The mode is only entered below this vehicle speed (plus the hysteresis once active). Stock 17.5 km/h. Effect: raise = mode entered at higher speed Evidence: ledger:E0347, ledger:E0429, ledger:E0441</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29742" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x182" flags="0x0">
    <title>Idle RPM-Control Mode - Speed Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle rpm-control mode entry. Added to the maximum speed while the mode is active. Stock 2 km/h. Effect: raise = mode held to a higher speed Evidence: ledger:E0347, ledger:E0429, ledger:E0441</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2974C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x183" flags="0x0">
    <title>Idle RPM-Control Mode - Entry Delay (rpm at/above desired)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle rpm-control mode entry. Time since the throttle closed before the mode is entered, when rpm is at or above desired. Stock 0.75 s. Effect: raise = later entry after a lift Evidence: ledger:E0347, ledger:E0429, ledger:E0441</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2974E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x184" flags="0x0">
    <title>Idle RPM-Control Mode - Entry Delay (rpm below desired)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle rpm-control mode entry. As above when rpm is below desired. Stock 0.0125 s. Effect: raise = later entry when rpm sags Evidence: ledger:E0347, ledger:E0429, ledger:E0441</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29750" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x185" flags="0x0">
    <title>Converter Model - Capacity Factor Band Half-Width</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Half-width of the capacity-factor band around the modelled value (stock 10 rpm per square root of Nm); both edges map through the expected speed ratio curve. Part of the torque converter model check: the PCM computes a converter capacity factor (engine speed over the square root of the torque going through the converter fluid, in rpm per square root of Nm), predicts the converter speed ratio from it and flags a mismatch when the measured speed ratio falls outside the band. Effect: converter model check Evidence: ledger:E0348, ledger:E1238</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9DE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm/sqrt(Nm)</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x186" flags="0x0">
    <title>Converter Model - Capacity Factor Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this capacity factor (stock 217 rpm per square root of Nm) the expected speed ratio is set to its maximum, so the upper band edge never flags. Part of the torque converter model check: the PCM computes a converter capacity factor (engine speed over the square root of the torque going through the converter fluid, in rpm per square root of Nm), predicts the converter speed ratio from it and flags a mismatch when the measured speed ratio falls outside the band. Effect: converter model check Evidence: ledger:E0348, ledger:E1238</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm/sqrt(Nm)</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x187" flags="0x0">
    <title>Upshift Hold RPM Ceiling - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = run the engine-speed ceiling while an upshift is held. Stock 0 (off). Part of the upshift-hold engine-speed ceiling: while the torque-based upshift inhibit holds a gear, this limits engine speed through a request to the engine side. Switched off on the stock H3 (enable = 0) (E0349). Effect: engine speed while an upshift is held Evidence: ledger:E0349</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x390AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0/1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x188" flags="0x0">
    <title>Upshift Hold RPM Ceiling - Release Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the release gear or above, the ceiling is dropped once engine rpm plus this offset passes it (stock 400 rpm). Part of the upshift-hold engine-speed ceiling: while the torque-based upshift inhibit holds a gear, this limits engine speed through a request to the engine side. Switched off on the stock H3 (enable = 0) (E0349). Effect: engine speed while an upshift is held Evidence: ledger:E0349</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x390AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x189" flags="0x0">
    <title>Upshift Hold RPM Ceiling - Band</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Band below the ceiling in which engine speed is tracked instead of clamped (stock 200 rpm). Part of the upshift-hold engine-speed ceiling: while the torque-based upshift inhibit holds a gear, this limits engine speed through a request to the engine side. Switched off on the stock H3 (enable = 0) (E0349). Effect: engine speed while an upshift is held Evidence: ledger:E0349</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x390AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x18A" flags="0x0">
    <title>Upshift Hold RPM Ceiling - Ramp Step Up (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Ramp step used when the ceiling rises (stock 2000). Part of the upshift-hold engine speed ceiling: while the upshift inhibit holds a gear, this limits engine speed through a request to the engine side. Switched off on the stock H3. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (switched off on the stock H3) Evidence: ledger:E0349, ledger:E0899</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x390B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x18B" flags="0x0">
    <title>Upshift Hold RPM Ceiling - Ramp Step Down (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Ramp step used when the ceiling falls (stock 2000). Part of the upshift-hold engine speed ceiling: while the upshift inhibit holds a gear, this limits engine speed through a request to the engine side. Switched off on the stock H3. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (switched off on the stock H3) Evidence: ledger:E0349, ledger:E0899</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x390B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x18C" flags="0x30">
    <title>Upshift Hold RPM Ceiling - Release Gear by Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or above this gear (per mode) the ceiling only releases, it does not clamp. Stock 4th in every mode. Part of the upshift-hold engine-speed ceiling: while the torque-based upshift inhibit holds a gear, this limits engine speed through a request to the engine side. Switched off on the stock H3 (enable = 0). Effect: engine speed while an upshift is held Evidence: ledger:E0349</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>mode</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x390B4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gear</units>
      <decimalpl>0</decimalpl>
      <min>1.000000</min>
      <max>65536.000000</max>
      <MATH equation="X+1"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x18D" flags="0x30">
    <title>Upshift Hold RPM Ceiling - Reduction Gain by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the coolant curve before it is subtracted from the base speed (stock 0.205 / 0.215 / 0.225 / 0.234). Part of the upshift-hold engine-speed ceiling: while the torque-based upshift inhibit holds a gear, this limits engine speed through a request to the engine side. Switched off on the stock H3 (enable = 0) (E0349). Effect: engine speed while an upshift is held Evidence: ledger:E0349</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>current gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x390C4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x18E" flags="0x30">
    <title>Upshift Hold RPM Ceiling - Reduction vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Amount taken off the WOT shift rpm by coolant temperature, before the per-gear gain. Part of the upshift-hold engine-speed ceiling: while the torque-based upshift inhibit holds a gear, this limits engine speed through a request to the engine side. Switched off on the stock H3 (enable = 0) (E0349). Effect: engine speed while an upshift is held Evidence: ledger:E0349, ledger:E0727</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x390CE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x18F" flags="0x30">
    <title>TCC Slip Control - Pressure Rate by Slip Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the slip controller changes converter clutch pressure, by slip error (slip minus slip target): pressure rises when slip is above target and falls when it is below. Stock 1.0 kPa/s at zero error, rising to 92.8 kPa/s at 280 rpm and above. Effect: raise = faster, harsher slip correction; lower = slower, softer Evidence: ledger:E0351, ledger:E0689, ledger:E1388, ledger:E1422</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-80" />
      <LABEL index="1" value="-42.663" />
      <LABEL index="2" value="-22.4" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="42.663" />
      <LABEL index="9" value="60" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="102.4" />
      <LABEL index="12" value="141.088" />
      <LABEL index="13" value="198.412" />
      <LABEL index="14" value="240" />
      <LABEL index="15" value="282.188" />
      <LABEL index="16" value="350" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D150" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa/s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>999.984741</max>
      <MATH equation="X/65.536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x190" flags="0x0">
    <title>TCC Slip Control - Low Slip Release Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the slip target is very low and slip is near zero, clutch pressure is lowered at this fixed rate instead of the normal rate curve (stock 48.8 kPa/s down). Effect: raise = clutch pressure backs off faster when it holds with no slip Evidence: ledger:E0351, ledger:E1422</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D17A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>999.984741</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65.536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x191" flags="0x0">
    <title>TCC Slip Control - Fixed Step Gate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The TCC slip controller uses its fixed step only while the slip target is below this value and slip is close to zero. Stock 31 rpm. Effect: TCC slip control response Evidence: ledger:E0351, ledger:E0679</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D188" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x192" flags="0x0">
    <title>TCC Slip Control - Fixed Step Slip Band</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The TCC slip controller uses its fixed step only while filtered slip (either direction) is below this. Stock 7 rpm. Each loop the controller adds a step sized by how far converter slip is from its target. Effect: TCC slip control response Evidence: ledger:E0351, ledger:E0679</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D18C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x193" flags="0x0">
    <title>TCC Slip Control - In-Shift Step Disable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = skip the in-shift step override. Stock 1 (override off). Part of the TCC slip controller: each loop the controller adds a step sized by how far converter slip is from its target (E0351). Effect: TCC slip control response Evidence: ledger:E0351, ledger:E0728</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D408" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>on/off (non-zero = override off)</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x194" flags="0x0">
    <title>TCC Slip Control - In-Shift Release Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During a downshift in the torque band, with the in-shift step enabled, clutch pressure is lowered at this rate while slip is below the in-shift threshold (stock 244 kPa/s down; the in-shift step is switched off on the stock calibration). Effect: no effect on the stock calibration (raise = faster pressure drop during a downshift when enabled) Evidence: ledger:E0351, ledger:E1422</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D17C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>999.984741</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65.536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x195" flags="0x0">
    <title>TCC Slip Control - In-Shift Step Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During a shift, with the torque band state set, the fixed shift step replaces the normal TCC slip step while filtered slip is below this value. Only used when the shift-step disable is 0 (stock 1, so off) (E0728). Effect: TCC slip control response Evidence: ledger:E0351, ledger:E0728</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D18A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x196" flags="0x30">
    <title>Road Load Torque vs Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque needed to hold a steady speed, before the learned offset (stock 0.08 at rest to 2.43 at 159 mph). Part of the road-load torque estimate: on throttle lift the upshift inhibit compares against the torque needed to hold speed (from this curve plus a learned offset) instead of the torque being delivered (E0352). Relative unit: the transmission&#x27;s torque model is scaled to its own full-scale engine torque, not to Nm (E0722). Effect: upshift hold on throttle lift Evidence: ledger:E0352, ledger:E0722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>mph</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="89" />
      <LABEL index="10" value="99" />
      <LABEL index="11" value="109" />
      <LABEL index="12" value="119" />
      <LABEL index="13" value="129" />
      <LABEL index="14" value="139" />
      <LABEL index="15" value="149" />
      <LABEL index="16" value="159" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F436" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x full-scale engine torque (at output)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x197" flags="0x30">
    <title>Road Load Learn Step vs Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Step added to the learned road-load offset each update at steady speed, by half the difference between delivered torque and the estimate (stock -163..122). Part of the road-load torque estimate: on throttle lift the upshift inhibit compares against the torque needed to hold speed (from this curve plus a learned offset) instead of the torque being delivered (E0352). Relative unit: the transmission&#x27;s torque model is scaled to its own full-scale engine torque, not to Nm (E0722). Effect: road-load learning rate Evidence: ledger:E0352, ledger:E0722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>(delivered - estimate) / 2 (raw)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-320" />
      <LABEL index="1" value="-280" />
      <LABEL index="2" value="-240" />
      <LABEL index="3" value="-200" />
      <LABEL index="4" value="-160" />
      <LABEL index="5" value="-120" />
      <LABEL index="6" value="-80" />
      <LABEL index="7" value="-40" />
      <LABEL index="8" value="0" />
      <LABEL index="9" value="40" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="120" />
      <LABEL index="12" value="160" />
      <LABEL index="13" value="200" />
      <LABEL index="14" value="240" />
      <LABEL index="15" value="280" />
      <LABEL index="16" value="320" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F45A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>x full-scale engine torque (at output)</units>
      <decimalpl>3</decimalpl>
      <min>-128.000000</min>
      <max>127.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x198" flags="0x0">
    <title>Road Load - Error Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Road load torque estimate (used for the upshift hold on throttle lift): filter on the difference between delivered torque and the estimate before it is used for learning. Stock 0: no filtering, each new reading is used as it is. A value of 0.5 keeps half of the old filtered value. Effect: raise = slower, smoother learning input Evidence: ledger:E1109</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F426" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x199" flags="0x0">
    <title>Road Load - Learn Acceleration Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Road load torque estimate (used for the upshift hold on throttle lift): the learned offset is updated only while the filtered vehicle acceleration is at or above this. Stock 0 with a maximum of 0: only at exactly steady speed. Effect: lower = learning also runs while slowing down Evidence: ledger:E1109</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F428" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h per s</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x19A" flags="0x0">
    <title>Road Load - Learn Acceleration Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Road load torque estimate (used for the upshift hold on throttle lift): the learned offset is updated only while the filtered vehicle acceleration is at or below this. Stock 0 with a minimum of 0: only at exactly steady speed. Effect: raise = learning also runs while speeding up Evidence: ledger:E1109</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F42A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h per s</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x19B" flags="0x0">
    <title>Road Load - Lift Hold Throttle Closing Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Road load torque estimate (used for the upshift hold on throttle lift): the lift hold starts when the throttle closes faster than this (a more negative rate) while delivered torque is at or below the road load figure. Stock 0: any closing of the throttle. Effect: lower (more negative) = only faster throttle lifts start the hold Evidence: ledger:E1109</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F42C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>% per s</units>
    <decimalpl>2</decimalpl>
    <min>-3200.000000</min>
    <max>3199.902344</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10.24"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x19C" flags="0x0">
    <title>Road Load - Learn Pause Throttle Opening Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Road load torque estimate (used for the upshift hold on throttle lift): a throttle opening rate above this pauses the learning of the offset for the learn pause time. Stock 0: any opening of the throttle. Effect: raise = only faster throttle openings pause the learning Evidence: ledger:E1109</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F42E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>% per s</units>
    <decimalpl>2</decimalpl>
    <min>-3200.000000</min>
    <max>3199.902344</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10.24"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x19D" flags="0x0">
    <title>Road Load - Learn Pause Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a fast throttle opening the learning of the road load offset pauses for this time. Stock 0: no pause. It does not affect the throttle lift hold. Part of the road load torque estimate the transmission uses for its upshift hold on throttle lift. Effect: raise = learning pauses longer after a throttle stab Evidence: ledger:E0352, ledger:E0722, ledger:E1102</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F430" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x19E" flags="0x0">
    <title>Road Load - Lift Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Longest the road-load lift hold lasts (stock 0, so a single pass). Part of the road-load torque estimate: on throttle lift the upshift inhibit compares against the torque needed to hold speed (from the road-load curve plus a learned offset) instead of the torque being delivered. Effect: upshift hold on throttle lift Evidence: ledger:E0352, ledger:E0722</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F432" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x19F" flags="0x30">
    <title>Pressure Control - Low Voltage Enter vs Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. System voltage below this suspends pressure control (stock 10.5 V at -40 C to 12.5 V at 152 C). Part of the pressure-control supply check: outside the voltage window the PCM suspends pressure-control solenoid operation until the voltage recovers (E0353). Effect: pressure control supply check Evidence: ledger:E0353, ledger:E0936</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>degC (trans temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E1F6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>V</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1A0" flags="0x30">
    <title>Pressure Control - Low Voltage Exit vs Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Voltage must rise above this to clear the low-voltage state (stock 11.0 V to 13.0 V). Part of the pressure-control supply check: outside the voltage window the PCM suspends pressure-control solenoid operation until the voltage recovers (E0353). Effect: pressure control supply check Evidence: ledger:E0353, ledger:E0936</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>degC (trans temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E1FC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>V</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1A1" flags="0x0">
    <title>Pressure Control - High Voltage Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. System voltage above this also suspends pressure control (stock 18.0 V). Part of the pressure-control supply check: outside the voltage window the PCM suspends pressure-control solenoid operation until the voltage recovers (E0353). Effect: pressure control supply check Evidence: ledger:E0353</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E212" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1A2" flags="0x0">
    <title>Pressure Control - Voltage Recovery Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the supply voltage must stay back inside the normal range before pressure control solenoid operation, suspended for low or high voltage, resumes. Stock about 0.04 seconds (37.5 ms). Effect: pressure control supply check Evidence: ledger:E0353, ledger:E0794</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E214" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1A3" flags="0x30">
    <title>Line Pressure Direction Hysteresis vs Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How far commanded line pressure must reverse before the PCM switches between the rising and falling force-motor tables, by transmission temperature. Stock 4 kPa flat. Effect: line pressure force-motor table selection Evidence: ledger:E0353, ledger:E1352</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (trans temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DF66" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>1020.000000</max>
      <MATH equation="X*4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1A4" flags="0x30">
    <title>TCC Pressure at Full Command vs Line Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. TCC apply pressure a 100 % command produces at each line pressure (stock 414 kPa at 0, 827 kPa from 320 kPa up). The TCC command is the commanded TCC pressure divided by this, so raising it lowers the command for the same requested pressure (softer apply); lowering it firms the apply (E0354). Effect: TCC apply command for a requested pressure Evidence: ledger:E0354</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3D4FA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>kPa (line pressure)</units>
      <embedinfo type="1" />
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D4AA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1A5" flags="0x0">
    <title>TCC Command - Offset Path Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = subtract the line-pressure offset curve from TCC pressure before scaling the command. Stock 0 (off). (E0354) Effect: TCC apply command Evidence: ledger:E0354</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C8B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0/1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1A6" flags="0x30">
    <title>TCC Command - Pressure Offset vs Line Pressure (offset path)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pressure subtracted from the commanded TCC pressure when the offset path is enabled (stock 265..709 kPa; unused, enable = 0). (E0354) Effect: TCC apply command (offset path only) Evidence: ledger:E0354</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3C8B6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>kPa (line pressure)</units>
      <embedinfo type="1" />
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C8CA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1A7" flags="0x0">
    <title>P0741 - Enable Min TCC Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded TCC pressure needed to run the test (stock 10 kPa). Part of the P0741 (TCC stuck off / performance) monitor: after each TCC apply, too much slip for too long counts a failure; two failures set the code (E0355). Effect: P0741 detection Evidence: ledger:E0355</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F6F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1A8" flags="0x0">
    <title>P0741 - Enable TCC Pressure Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the TCC pressure condition must hold (stock 0.05 s). Part of the P0741 (TCC stuck off / performance) monitor: after each TCC apply, too much slip for too long counts a failure; two failures set the code (E0355). Effect: P0741 detection Evidence: ledger:E0355</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F6F8" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1A9" flags="0x0">
    <title>P0741 - Enable Min TCC Command</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. TCC command needed to run the test (stock 65 %). Part of the P0741 (TCC stuck off / performance) monitor: after each TCC apply, too much slip for too long counts a failure; two failures set the code (E0355). Effect: P0741 detection Evidence: ledger:E0355</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F6AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1AA" flags="0x0">
    <title>P0741 - Enable TCC Command Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the TCC command condition must hold (stock 2.0 s). Part of the P0741 (TCC stuck off / performance) monitor: after each TCC apply, too much slip for too long counts a failure; two failures set the code (E0355). Effect: P0741 detection Evidence: ledger:E0355</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F6D8" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1AB" flags="0x30">
    <title>Tip-In Torque Mgmt - Starting Torque by Range and Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): the tip-in torque limit starts from the current engine torque or this, whichever is higher, by forward range (rows) and gear (columns). Stock 0 / 5 / 10 / 20 / 20 / 20 Nm in every range. Effect: raise = tip-ins start from more torque (less softening) Evidence: ledger:E0356</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>forward range</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="range 0" />
      <LABEL index="1" value="range 1" />
      <LABEL index="2" value="range 2" />
      <LABEL index="3" value="range 3" />
      <LABEL index="4" value="range 4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x214C4" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1AC" flags="0x0">
    <title>Tip-In Torque Mgmt - Arm Below Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): a tip-in can only be armed while engine torque is below this. Stock 50 Nm. Effect: raise = arms at higher coast torque Evidence: ledger:E0356</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21518" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1AD" flags="0x0">
    <title>Tip-In Torque Mgmt - Cancel Above Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): the tip-in limit is cancelled once engine torque is above this. Stock 100 Nm. Effect: raise = limit stays on to higher torque Evidence: ledger:E0356</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2151A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1AE" flags="0x0">
    <title>Tip-In Torque Mgmt - Ramp End Margin</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): the torque ramp counts as complete once it has climbed this far above its starting torque. Stock 130 Nm. Effect: raise = longer ramp Evidence: ledger:E0356</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2151E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1AF" flags="0x30">
    <title>Tip-In Torque Ramp - Fast Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up by a step each update. The step is the default step normally, the slow lash step while the driveline is taking up slack (gearbox slip above about 10 rpm, or engine speed rising faster than the slip-based limit), and the fast step once the limit has passed its target. This is the fast step, by throttle. Effect: raise = the torque limit catches up faster at the end of a tip-in Evidence: ledger:E0356, ledger:E0395, ledger:E0845</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% throttle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2154C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm per update</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1B0" flags="0x30">
    <title>Tip-In Torque Ramp - Lash Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up by a step each update. The step is the default step normally, the slow lash step while the driveline is taking up slack (gearbox slip above about 10 rpm, or engine speed rising faster than the slip-based limit), and the fast step once the limit has passed its target. This is the lash step, by throttle, before the engine speed factor is applied (the step used is this value times the factor). Effect: raise = torque builds faster while the driveline takes up slack (more clunk) Evidence: ledger:E0356, ledger:E0395, ledger:E0845</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% throttle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21570" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm per update</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1B1" flags="0x30">
    <title>Tip-In Torque Ramp - Default Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up by a step each update. The step is the default step normally, the slow lash step while the driveline is taking up slack (gearbox slip above about 10 rpm, or engine speed rising faster than the slip-based limit), and the fast step once the limit has passed its target. This is the default step, by throttle. Effect: raise = faster torque build-up after a tip-in Evidence: ledger:E0356, ledger:E0395, ledger:E0845</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% throttle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21594" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm per update</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1B2" flags="0x30">
    <title>Tip-In Torque Ramp - Lash Step Engine Speed Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up by a step each update. The step is the default step normally, the slow lash step while the driveline is taking up slack (gearbox slip above about 10 rpm, or engine speed rising faster than the slip-based limit), and the fast step once the limit has passed its target. Multiplies the lash step, by engine speed. Stock about 0.10 to 0.14. Effect: raise = larger lash step at that engine speed Evidence: ledger:E0356, ledger:E0395, ledger:E0845</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1600" />
      <LABEL index="3" value="2400" />
      <LABEL index="4" value="3200" />
      <LABEL index="5" value="4000" />
      <LABEL index="6" value="4800" />
      <LABEL index="7" value="5600" />
      <LABEL index="8" value="6400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21538" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>-8.000000</min>
      <max>7.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1B3" flags="0x30">
    <title>Tip-In Torque Ramp - Engine Speed Rise Limit vs Slip</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up by a step each update. The step is the default step normally, the slow lash step while the driveline is taking up slack (gearbox slip above about 10 rpm, or engine speed rising faster than the slip-based limit), and the fast step once the limit has passed its target. If engine speed rises faster than this per update at the current gearbox slip, the lash step is used. Stock 90 rpm per update at negative slip, tapering to 0 by 50 rpm. Effect: lower = the lash step engages on smaller engine speed flares Evidence: ledger:E0356, ledger:E03...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (gearbox slip)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-750" />
      <LABEL index="1" value="-700" />
      <LABEL index="2" value="-650" />
      <LABEL index="3" value="-600" />
      <LABEL index="4" value="-550" />
      <LABEL index="5" value="-500" />
      <LABEL index="6" value="-450" />
      <LABEL index="7" value="-400" />
      <LABEL index="8" value="-350" />
      <LABEL index="9" value="-300" />
      <LABEL index="10" value="-250" />
      <LABEL index="11" value="-200" />
      <LABEL index="12" value="-150" />
      <LABEL index="13" value="-100" />
      <LABEL index="14" value="-50" />
      <LABEL index="15" value="0" />
      <LABEL index="16" value="50" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x215B8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm per update</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1B4" flags="0x30">
    <title>Tip-In Torque Mgmt - Input Speed Rate Threshold (rise)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. Shunt detection: transmission input speed rising faster than this per update, by input speed, marks a driveline shunt. Stock 16 to 40 rpm per update. Effect: lower = shunt / swing-back detected sooner, so the fast step comes in sooner Evidence: ledger:E0356, ledger:E0689, ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.1" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1599.9" />
      <LABEL index="3" value="2399.8" />
      <LABEL index="4" value="3199.7" />
      <LABEL index="5" value="3999.6" />
      <LABEL index="6" value="4799.5" />
      <LABEL index="7" value="5599.4" />
      <LABEL index="8" value="6399.3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x215DC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm per update</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1B5" flags="0x30">
    <title>Tip-In Torque Mgmt - Input Speed Rate Threshold (fall)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. Swing-back detection: after a shunt, input speed falling faster than this per update, by input speed, marks the swing back. Stock -20 to -70 rpm per update. Effect: closer to zero = swing-back detected sooner Evidence: ledger:E0356, ledger:E0689, ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.1" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1599.9" />
      <LABEL index="3" value="2399.8" />
      <LABEL index="4" value="3199.7" />
      <LABEL index="5" value="3999.6" />
      <LABEL index="6" value="4799.5" />
      <LABEL index="7" value="5599.4" />
      <LABEL index="8" value="6399.3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x215F0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm per update</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1B6" flags="0x30">
    <title>Tip-In Torque Mgmt - Vehicle Speed Rate Threshold (rise)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. Shunt detection on vehicle speed change per update, by vehicle speed. Stock off (maximum value). Effect: lower = shunt / swing-back detected sooner, so the fast step comes in sooner Evidence: ledger:E0356, ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21604" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per update</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1B7" flags="0x30">
    <title>Tip-In Torque Mgmt - Vehicle Speed Rate Threshold (fall)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. Swing-back detection on vehicle speed change per update, by vehicle speed. Stock off (minimum value). Effect: closer to zero = swing-back detected sooner Evidence: ledger:E0356, ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21618" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per update</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1B8" flags="0x30">
    <title>Cam Phasing (load) - Target vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Load-based exhaust cam phasing: desired cam angle by rpm. Stock 0 deg up to 1600 rpm, 9 deg from 2000, 10 to 11 deg above. The code path is traced; a loaded drive log has not yet shown the cam moving. Values are desired-cam degrees; the VE model&#x27;s cam axis counts twice as many units per degree (9 here is about 18 on that axis). Effect: changes exhaust cam phasing under load Evidence: ledger:E0358</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="400" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1200" />
      <LABEL index="4" value="1600" />
      <LABEL index="5" value="2000" />
      <LABEL index="6" value="2400" />
      <LABEL index="7" value="2800" />
      <LABEL index="8" value="3200" />
      <LABEL index="9" value="3600" />
      <LABEL index="10" value="4000" />
      <LABEL index="11" value="4400" />
      <LABEL index="12" value="4800" />
      <LABEL index="13" value="5200" />
      <LABEL index="14" value="5600" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22F9E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1B9" flags="0x30">
    <title>Cam Phasing (load) - Coolant Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Load-based exhaust cam phasing: multiplies the target by coolant temperature. Stock 0.5 cold, 1.0 warm. The code path is traced; a loaded drive log has not yet shown the cam moving. Effect: changes exhaust cam phasing under load Evidence: ledger:E0358</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22FC2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1BA" flags="0x30">
    <title>Load-Based Cam Phasing - Pedal Demand Threshold vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Load-based cam phasing: above this pedal demand (percent of throttle area the driver is asking for) the cam is phased by the load-based cam target instead of the base schedule. Threshold by engine speed. Stock 110 % (never) up to 1200 rpm, 28.2 % from 1600 rpm. Effect: lower = load-based cam phasing starts at lighter pedal Evidence: ledger:E0358, ledger:E0872</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="400" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1200" />
      <LABEL index="4" value="1600" />
      <LABEL index="5" value="2000" />
      <LABEL index="6" value="2400" />
      <LABEL index="7" value="2800" />
      <LABEL index="8" value="3200" />
      <LABEL index="9" value="3600" />
      <LABEL index="10" value="4000" />
      <LABEL index="11" value="4400" />
      <LABEL index="12" value="4800" />
      <LABEL index="13" value="5200" />
      <LABEL index="14" value="5600" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2309E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (pedal area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.000000</max>
      <MATH equation="X/327.675"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1BB" flags="0x30">
    <title>Cam Phasing (load) - Run-Time Delay vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Load-based exhaust cam phasing: run time after start, by coolant temperature, before the path may act. The code path is traced; a loaded drive log has not yet shown the cam moving. Effect: changes exhaust cam phasing under load Evidence: ledger:E0358</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22D80" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1BC" flags="0x0">
    <title>Load-Based Cam Ramp - Throttle Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Load-based cam phasing: when the load-based cam target takes over, the commanded cam angle ramps toward it by the ramp step each update while throttle is below the throttle limit and vehicle speed is above the speed limit; otherwise it jumps straight to the target. At or above this throttle the cam jumps to the target. Stock 80 %. Effect: lower = the cam jumps sooner at high throttle Evidence: ledger:E0358, ledger:E0874</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x23096" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1BD" flags="0x30">
    <title>Line Pressure - Source 4 Pressure vs Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded line pressure, by throttle, while the transmission&#x27;s slip monitor has caught possible clutch slip: converter slip between 120 and 550 rpm, with throttle inside the monitor&#x27;s window, for about 10 seconds. At that point the PCM records a slipping sample and uses this table until the slip or throttle condition ends. Stock 68 kPa across the whole throttle range. The table is also used while the transmission range switch reading is invalid (no valid range for the confirm time). Effect: raise = increases the line pressure commanded while the slip-check mode is active Evidence: ledger:E0360, ledger:E0786, ledger:...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% throttle area</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="6.2" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.8" />
      <LABEL index="4" value="25.0" />
      <LABEL index="5" value="31.2" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.8" />
      <LABEL index="8" value="50.0" />
      <LABEL index="9" value="56.2" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.8" />
      <LABEL index="12" value="75.0" />
      <LABEL index="13" value="81.2" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.8" />
      <LABEL index="16" value="100.0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E21E" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>1020.000000</max>
      <MATH equation="X*4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1BE" flags="0x30">
    <title>Catalyst Temp Model - Steady State vs RPM vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst temperature model: the base catalyst temperature the model heads toward, by rpm (rows) and engine airflow (columns). The over-temperature protection enriches when the model runs hot. Effect: raise = model runs hotter, protection enrichment starts sooner Evidence: ledger:E0363</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <LABEL index="11" value="110" />
      <LABEL index="12" value="120" />
      <LABEL index="13" value="130" />
      <LABEL index="14" value="140" />
      <LABEL index="15" value="150" />
      <LABEL index="16" value="160" />
      <LABEL index="17" value="170" />
      <LABEL index="18" value="180" />
      <LABEL index="19" value="190" />
      <LABEL index="20" value="200" />
      <LABEL index="21" value="210" />
      <LABEL index="22" value="220" />
      <LABEL index="23" value="230" />
      <LABEL index="24" value="240" />
      <LABEL index="25" value="250" />
      <LABEL index="26" value="260" />
      <LABEL index="27" value="270" />
      <LABEL index="28" value="280" />
      <LABEL index="29" value="290" />
      <LABEL index="30" value="300" />
      <LABEL index="31" value="310" />
      <LABEL index="32" value="320" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="400" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1200" />
      <LABEL index="4" value="1600" />
      <LABEL index="5" value="2000" />
      <LABEL index="6" value="2400" />
      <LABEL index="7" value="2800" />
      <LABEL index="8" value="3200" />
      <LABEL index="9" value="3600" />
      <LABEL index="10" value="4000" />
      <LABEL index="11" value="4400" />
      <LABEL index="12" value="4800" />
      <LABEL index="13" value="5200" />
      <LABEL index="14" value="5600" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x219B6" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1BF" flags="0x30">
    <title>Catalyst Temp Model - Vehicle Speed Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst temperature model: added to the target by vehicle speed. Stock +58 C flat. Effect: raise = model runs hotter in that range Evidence: ledger:E0363</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="32" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="96" />
      <LABEL index="4" value="128" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="192" />
      <LABEL index="7" value="224" />
      <LABEL index="8" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21E1A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1C0" flags="0x30">
    <title>Catalyst Temp Model - Commanded EQ Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst temperature model: added to the target by commanded fuel (EQ); richer fuel lowers it. Stock +434 C at EQ 0.92 to +179 C at EQ 1.56. Effect: raise = model runs hotter in that range Evidence: ledger:E0363</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>EQ</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.92" />
      <LABEL index="1" value="0.96" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="1.04" />
      <LABEL index="4" value="1.08" />
      <LABEL index="5" value="1.12" />
      <LABEL index="6" value="1.16" />
      <LABEL index="7" value="1.2" />
      <LABEL index="8" value="1.24" />
      <LABEL index="9" value="1.28" />
      <LABEL index="10" value="1.32" />
      <LABEL index="11" value="1.36" />
      <LABEL index="12" value="1.4" />
      <LABEL index="13" value="1.44" />
      <LABEL index="14" value="1.48" />
      <LABEL index="15" value="1.52" />
      <LABEL index="16" value="1.56" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21968" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1C1" flags="0x30">
    <title>Catalyst Temp Model - RPM Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst temperature model: added to the target by rpm (times a cylinder factor). Stock 0 to -300 C. Effect: raise = model runs hotter in that range Evidence: ledger:E0363</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="400" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1200" />
      <LABEL index="4" value="1600" />
      <LABEL index="5" value="2000" />
      <LABEL index="6" value="2400" />
      <LABEL index="7" value="2800" />
      <LABEL index="8" value="3200" />
      <LABEL index="9" value="3600" />
      <LABEL index="10" value="4000" />
      <LABEL index="11" value="4400" />
      <LABEL index="12" value="4800" />
      <LABEL index="13" value="5200" />
      <LABEL index="14" value="5600" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21944" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1C2" flags="0x30">
    <title>Catalyst Over-Temp Protection - Ramp-In Step vs Over-Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. how fast protection enrichment rises, by how far the model&#x27;s target is above the base temperature. Stock 0 to 0.535 EQ per update over 0-200 C. Effect: raise = faster enrichment change Evidence: ledger:E0363</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="12.5" />
      <LABEL index="2" value="25" />
      <LABEL index="3" value="37.5" />
      <LABEL index="4" value="50" />
      <LABEL index="5" value="62.5" />
      <LABEL index="6" value="75" />
      <LABEL index="7" value="87.5" />
      <LABEL index="8" value="100" />
      <LABEL index="9" value="112.5" />
      <LABEL index="10" value="125" />
      <LABEL index="11" value="137.5" />
      <LABEL index="12" value="150" />
      <LABEL index="13" value="162.5" />
      <LABEL index="14" value="175" />
      <LABEL index="15" value="187.5" />
      <LABEL index="16" value="200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21872" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ per update</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1C3" flags="0x30">
    <title>Catalyst Over-Temp Protection - Ramp-Out Step vs Under-Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. how fast protection enrichment is removed, by how far the target is below the base temperature. Stock 0 to 0.268 EQ per update. Effect: raise = faster enrichment change Evidence: ledger:E0363</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="12.5" />
      <LABEL index="2" value="25" />
      <LABEL index="3" value="37.5" />
      <LABEL index="4" value="50" />
      <LABEL index="5" value="62.5" />
      <LABEL index="6" value="75" />
      <LABEL index="7" value="87.5" />
      <LABEL index="8" value="100" />
      <LABEL index="9" value="112.5" />
      <LABEL index="10" value="125" />
      <LABEL index="11" value="137.5" />
      <LABEL index="12" value="150" />
      <LABEL index="13" value="162.5" />
      <LABEL index="14" value="175" />
      <LABEL index="15" value="187.5" />
      <LABEL index="16" value="200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21896" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ per update</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1C4" flags="0x0">
    <title>Catalyst Over-Temp Protection - Ramp Base Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The ramp-in and ramp-out steps are looked up by how far the model&#x27;s target temperature is above or below this. Stock 975 C. Effect: lower = ramps react at cooler targets Evidence: ledger:E0363</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2186E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1C5" flags="0x30">
    <title>Catalyst Temperature Model - Spark Retard Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the catalyst temperature model target by spark retard from best torque timing, as a fraction of (MBT spark - Spark Retard Reference Offset), 0 to 1. Stock 107 C with no retard rising to 338 C at full retard. The catalyst temperature model (used by catalyst overtemperature protection) moves toward a target built from engine speed and airflow, vehicle speed, commanded fuel ratio, spark retard and an rpm term. Effect: raise = the modelled catalyst temperature target is hotter with spark retard Evidence: ledger:E0363, ledger:E1457</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>spark retard / reference</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.062" />
      <LABEL index="2" value="0.125" />
      <LABEL index="3" value="0.188" />
      <LABEL index="4" value="0.25" />
      <LABEL index="5" value="0.312" />
      <LABEL index="6" value="0.375" />
      <LABEL index="7" value="0.438" />
      <LABEL index="8" value="0.5" />
      <LABEL index="9" value="0.562" />
      <LABEL index="10" value="0.625" />
      <LABEL index="11" value="0.688" />
      <LABEL index="12" value="0.75" />
      <LABEL index="13" value="0.812" />
      <LABEL index="14" value="0.875" />
      <LABEL index="15" value="0.938" />
      <LABEL index="16" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2198C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1C6" flags="0x30">
    <title>Catalyst Temperature Model - Heating Rate Factor vs Temperature Gap</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on how fast the PCM&#x27;s modelled catalyst temperature rises toward its target, by how far the target is above the model (axis -1200 to +1200 C; only the positive half is used, since this factor applies while the model heats). It multiplies the heating rate factor vs airflow. Stock 1.0 at every point. Changes the modelled temperature that drives catalyst overtemperature protection. Effect: raise = the modelled catalyst temperature climbs faster at that gap Evidence: ledger:E0363, ledger:E0937, ledger:E1242</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (target minus model)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-1200" />
      <LABEL index="1" value="-1050" />
      <LABEL index="2" value="-900" />
      <LABEL index="3" value="-750" />
      <LABEL index="4" value="-600" />
      <LABEL index="5" value="-450" />
      <LABEL index="6" value="-300" />
      <LABEL index="7" value="-150" />
      <LABEL index="8" value="0" />
      <LABEL index="9" value="150" />
      <LABEL index="10" value="300" />
      <LABEL index="11" value="450" />
      <LABEL index="12" value="600" />
      <LABEL index="13" value="750" />
      <LABEL index="14" value="900" />
      <LABEL index="15" value="1050" />
      <LABEL index="16" value="1200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21E2E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1C7" flags="0x30">
    <title>Catalyst Temperature Model - Heating Rate Factor vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on how fast the PCM&#x27;s modelled catalyst temperature rises toward its target when the target is higher, by airflow (0 to 400 g/s); it multiplies the heating rate. Stock 0.01 at no airflow rising to 0.43. Changes the modelled temperature that drives catalyst overtemperature protection. Effect: raise = the modelled catalyst temperature climbs faster Evidence: ledger:E0363, ledger:E0689, ledger:E0936, ledger:E0949</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>g/s (airflow)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="25" />
      <LABEL index="2" value="50" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="100" />
      <LABEL index="5" value="125" />
      <LABEL index="6" value="150" />
      <LABEL index="7" value="175" />
      <LABEL index="8" value="200" />
      <LABEL index="9" value="225" />
      <LABEL index="10" value="250" />
      <LABEL index="11" value="275" />
      <LABEL index="12" value="300" />
      <LABEL index="13" value="325" />
      <LABEL index="14" value="350" />
      <LABEL index="15" value="375" />
      <LABEL index="16" value="400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x218EA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1C8" flags="0x30">
    <title>Catalyst Temperature Model - Cooling Rate vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the PCM&#x27;s modelled catalyst temperature falls toward its target when the target is lower, by airflow (0 to 400 g/s): the fraction of the gap closed per update. Stock 0.02 at no airflow rising to 0.32. Changes the modelled temperature that drives catalyst overtemperature protection. Effect: raise = the modelled catalyst temperature drops faster Evidence: ledger:E0363, ledger:E0936, ledger:E0949</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>g/s (airflow)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="25" />
      <LABEL index="2" value="50" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="100" />
      <LABEL index="5" value="125" />
      <LABEL index="6" value="150" />
      <LABEL index="7" value="175" />
      <LABEL index="8" value="200" />
      <LABEL index="9" value="225" />
      <LABEL index="10" value="250" />
      <LABEL index="11" value="275" />
      <LABEL index="12" value="300" />
      <LABEL index="13" value="325" />
      <LABEL index="14" value="350" />
      <LABEL index="15" value="375" />
      <LABEL index="16" value="400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x218C6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1C9" flags="0x30">
    <title>Catalyst Temp Model - Start-Up Pull Toward Intake Air</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At start-up the modelled catalyst temperature is moved this share of the way from its last value toward the intake air temperature, by how long the engine was off (0 to 18.2 h). Stock 1.6 % right after shut-off, rising to 7.0 % after 18 h. Effect: raise = the modelled catalyst temperature starts closer to intake air temperature after a stop Evidence: ledger:E0363, ledger:E0936, ledger:E1186</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>h (engine-off time)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1.138" />
      <LABEL index="2" value="2.276" />
      <LABEL index="3" value="3.413" />
      <LABEL index="4" value="4.551" />
      <LABEL index="5" value="5.689" />
      <LABEL index="6" value="6.827" />
      <LABEL index="7" value="7.964" />
      <LABEL index="8" value="9.102" />
      <LABEL index="9" value="10.24" />
      <LABEL index="10" value="11.378" />
      <LABEL index="11" value="12.516" />
      <LABEL index="12" value="13.653" />
      <LABEL index="13" value="14.791" />
      <LABEL index="14" value="15.929" />
      <LABEL index="15" value="17.067" />
      <LABEL index="16" value="18.204" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21920" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% of gap closed</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1CA" flags="0x30">
    <title>Knock Detection - Threshold Gain, Slot 1</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection (safety relevant). Threshold gain for knock loop slot 1 (the slot is the position in the knock module&#x27;s per-cylinder loop), by airmass (rows) and rpm (columns). The knock threshold is the background level plus this gain times the knock noise deviation, so 1.0 means one noise deviation above background. Stock 2.50 to 3.50. Raising it makes knock detection less sensitive. Effect: raise = a stronger knock signal is needed before knock retard (less sensitive) Evidence: ledger:E0364, ledger:E0703</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="500" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1500" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2500" />
      <LABEL index="6" value="3000" />
      <LABEL index="7" value="3500" />
      <LABEL index="8" value="4000" />
      <LABEL index="9" value="4500" />
      <LABEL index="10" value="5000" />
      <LABEL index="11" value="5500" />
      <LABEL index="12" value="6000" />
      <LABEL index="13" value="6500" />
      <LABEL index="14" value="7000" />
      <LABEL index="15" value="7500" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>g/cyl (airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.24" />
      <LABEL index="1" value="0.3" />
      <LABEL index="2" value="0.36" />
      <LABEL index="3" value="0.42" />
      <LABEL index="4" value="0.48" />
      <LABEL index="5" value="0.54" />
      <LABEL index="6" value="0.6" />
      <LABEL index="7" value="0.66" />
      <LABEL index="8" value="0.72" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31EBA" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain (x knock noise)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>127.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1CB" flags="0x30">
    <title>Knock Detection - Threshold Gain Factor vs Commanded EQ</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection (safety relevant). Multiplies every slot&#x27;s threshold gain by the commanded equivalence ratio. Stock 1.00 at EQ 1.00 rising to 1.35 from EQ 1.34 (richer = less sensitive). Effect: raise = less knock sensitivity when running rich Evidence: ledger:E0364</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>EQ ratio</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="1.056" />
      <LABEL index="2" value="1.113" />
      <LABEL index="3" value="1.169" />
      <LABEL index="4" value="1.225" />
      <LABEL index="5" value="1.281" />
      <LABEL index="6" value="1.337" />
      <LABEL index="7" value="1.394" />
      <LABEL index="8" value="1.45" />
      <LABEL index="9" value="1.506" />
      <LABEL index="10" value="1.562" />
      <LABEL index="11" value="1.619" />
      <LABEL index="12" value="1.675" />
      <LABEL index="13" value="1.731" />
      <LABEL index="14" value="1.788" />
      <LABEL index="15" value="1.844" />
      <LABEL index="16" value="1.9" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x32620" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1CC" flags="0x30">
    <title>Knock Detection - Transient Threshold Adder vs RPM (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection (safety relevant). Added to the threshold gain while a transient (rpm, throttle or airmass change) is active. All zero on the stock H3, so it has no effect as delivered. Effect: raise = less knock sensitivity during transients Evidence: ledger:E0364, ledger:E0703</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="500" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1500" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2500" />
      <LABEL index="6" value="3000" />
      <LABEL index="7" value="3500" />
      <LABEL index="8" value="4000" />
      <LABEL index="9" value="4500" />
      <LABEL index="10" value="5000" />
      <LABEL index="11" value="5500" />
      <LABEL index="12" value="6000" />
      <LABEL index="13" value="6500" />
      <LABEL index="14" value="7000" />
      <LABEL index="15" value="7500" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x325FC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain (x knock noise)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>127.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1CD" flags="0x0">
    <title>Knock Detection - Transient Trigger, Engine Speed Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: while a transient is flagged the noise level tracking uses its transient settings and the knock threshold learn is paused. A rising transient is flagged when engine speed has risen by at least this across the 40 sample speed history. Stock 50 rpm. Effect: raise = fewer accelerations are treated as a transient Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31D38" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1CE" flags="0x0">
    <title>Knock Detection - Transient Trigger, Engine Speed Fall</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: while a transient is flagged the noise level tracking uses its transient settings and the knock threshold learn is paused. A falling transient is flagged when engine speed has changed by this or less (a fall) across the 40 sample speed history. Stock -50 rpm. Effect: more negative = fewer decelerations are treated as a transient Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31D3A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1CF" flags="0x0">
    <title>Knock Detection - Transient Trigger, Throttle Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: while a transient is flagged the noise level tracking uses its transient settings and the knock threshold learn is paused. A rising transient is flagged when the throttle has opened by at least this across the 5 sample throttle history. Stock 15 %. Effect: raise = fewer throttle openings are treated as a transient Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31D3C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>-200.000000</min>
    <max>199.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1D0" flags="0x0">
    <title>Knock Detection - Transient Trigger, Throttle Fall</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: while a transient is flagged the noise level tracking uses its transient settings and the knock threshold learn is paused. A falling transient is flagged when the throttle has changed by this or less (closing) across the 5 sample throttle history. Stock -15 %. Effect: more negative = fewer throttle closings are treated as a transient Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31D3E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>-200.000000</min>
    <max>199.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1D1" flags="0x0">
    <title>Knock Detection - Transient Trigger, Airmass Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: while a transient is flagged the noise level tracking uses its transient settings and the knock threshold learn is paused. A transient is flagged when the cylinder airmass differs from its filtered value by at least this, in either direction. Stock 0.0009 g per cylinder. Effect: raise = fewer load changes are treated as a transient Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31D40" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/cyl</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.095937</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1D2" flags="0x0">
    <title>Knock Detection - Airmass Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: share of the gap to the new cylinder airmass that the filtered airmass closes on each update. The filtered value is the reference of the airmass step trigger. Stock 0.95. Effect: lower = slower filter, load changes are flagged as a transient more easily Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31D42" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1D3" flags="0x30">
    <title>TAP Learn - Max Vehicle Speed by Shift</title>
    <description>Change in small steps and log. Each row is [COUNT = 17][17 points]; COUNT is a structure word, never edit it (E0366). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this trans-side vehicle speed a shift is not learned. Stock 500 km/h (no limit) for 1-2 and 2-3, 0 for 3-4 (3-4 never learns). TAP (adaptive shift pressure) only learns on shifts inside every enable window (E0366). Effect: which shifts TAP learns from Evidence: ledger:E0366, ledger:E0714, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C316" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1D4" flags="0x30">
    <title>TAP Learn - Min Torque by Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this shift torque, a shift is not used to adjust the learned shift pressure. Applies separately to the 1-2 and 2-3 upshifts (stock 200 Nm) and to the 3-4 upshift (stock 0, so learning is disabled for that shift). The adaptive shift pressure learning only updates from shifts whose torque falls inside this window. Effect: which shifts TAP learns from Evidence: ledger:E0366, ledger:E0794</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C538" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1D5" flags="0x30">
    <title>TAP Learn - Max Torque by Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this shift torque, a shift is not used to adjust the learned shift pressure. Applies separately to the 1-2 and 2-3 upshifts (stock about 2034 Nm, so it never limits in practice) and to the 3-4 upshift (stock 0). The adaptive shift pressure learning only updates from shifts whose torque falls inside this window. Effect: which shifts TAP learns from Evidence: ledger:E0366, ledger:E0794</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C532" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1D6" flags="0x30">
    <title>Knock Sensing Window Position vs RPM x Airmass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Where the knock sensing window sits, in crank degrees counted from each cylinder&#x27;s reference tooth on the crank wheel, by engine speed (columns) and cylinder airmass (rows). The PCM converts it to whole teeth plus a fraction of a tooth for the knock window hardware; the window length is the separate curve vs engine speed. Stock 0 deg at 0.24 g/cyl, 4 deg at 0.30 g/cyl, then 8.7 to 35.1 deg (falling with engine speed). Effect: do not edit: moves the crank angle where the knock sensor is listened to; a wrong window can hide real knock Evidence: ledger:E0367, ledger:E1180</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="500" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1500" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2500" />
      <LABEL index="6" value="3000" />
      <LABEL index="7" value="3500" />
      <LABEL index="8" value="4000" />
      <LABEL index="9" value="4500" />
      <LABEL index="10" value="5000" />
      <LABEL index="11" value="5500" />
      <LABEL index="12" value="6000" />
      <LABEL index="13" value="6500" />
      <LABEL index="14" value="7000" />
      <LABEL index="15" value="7500" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>g/cyl (filtered airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.24" />
      <LABEL index="1" value="0.3" />
      <LABEL index="2" value="0.36" />
      <LABEL index="3" value="0.42" />
      <LABEL index="4" value="0.48" />
      <LABEL index="5" value="0.54" />
      <LABEL index="6" value="0.6" />
      <LABEL index="7" value="0.66" />
      <LABEL index="8" value="0.72" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31D5A" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>deg (crank, from cylinder reference tooth)</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1023.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1D7" flags="0x0">
    <title>Shift Pressure Multiplier - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = apply the per-shift shift pressure multiplier tables. Stock 0 (off). Multiplies base shift pressure only when the enable is set; stock 0, so unused on the H3. Effect: shift firmness Evidence: ledger:E0368</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3A09E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0/1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1D8" flags="0x30">
    <title>Start-Up Fuel - Event Count vs Coolant (by group)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up fuel: number of cylinder events that get a start-up pulse once crank / cam sync is gained, by coolant band (columns) and by when sync was gained (rows). Row 1 to 4 apply only when the pre-sync pulse sequence is on and sync arrives on crank reference event 3 to 6 of a pre-sync round; that sequence is switched off on the stock H3, so only the first row is used. Stock first row: 3 events at -25 C and below, 4 otherwise; other rows 0. Effect: more events = more cylinders get a start-up pulse Evidence: ledger:E0369, ledger:E1281</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>coolant band</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="&lt;= -25 C" />
      <LABEL index="1" value="-25..-15 C" />
      <LABEL index="2" value="-15..5 C" />
      <LABEL index="3" value="5..15 C" />
      <LABEL index="4" value="15..55 C" />
      <LABEL index="5" value="55..105 C" />
      <LABEL index="6" value="&gt; 105 C" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>sync point</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sync at start" />
      <LABEL index="1" value="sync on event 3" />
      <LABEL index="2" value="sync on event 4" />
      <LABEL index="3" value="sync on event 5" />
      <LABEL index="4" value="sync on event 6" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25372" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>events</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1D9" flags="0x30">
    <title>Start-Up Fuel - Multiplier vs Events Still To Come</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up fuel events (one-shot pulses written for the first cylinder events at start-up). Multiplies each start-up pulse; index = events still to come after this one (the last event uses index 0). Stock 1.0 for 0 to 5 (only 0 to 3 used with the stock event counts), then 0.9 at 6 and 7, 0.8 at 8 and 9, 0.7 at 10 and 11, 0.6 at 12 and 13, 0.5 at 14 and 15. Event counts above 16 are not usable: the per-event trim lookup runs out of its table. Effect: raise = richer start-up pulses Evidence: ledger:E0369, ledger:E1183</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>16</indexcount>
      <units>events to come</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x254BA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1DA" flags="0x30">
    <title>Start-Up Fuel - Second Multiplier vs Count x Events To Come (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up fuel events (one-shot pulses written for the first cylinder events at start-up). Second per-event multiplier, row = event count - 1, column = events still to come. All 1.0 on the stock H3 (inert). Effect: raise = richer start-up pulses Evidence: ledger:E0369</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>16</indexcount>
      <units>events to come</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>16</indexcount>
      <units>event count</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x253BA" mmedelementsizebits="8" mmedrowcount="16" mmedcolcount="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1DB" flags="0x30">
    <title>Throttle Actuator Servo Gains vs Battery Voltage (raw, DO NOT EDIT)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Five gains of the electronic throttle&#x27;s position servo (rows) by battery voltage, 2 to 18 V (columns). Values are the servo&#x27;s internal gain counts, shown raw. Not a tuning item. DO NOT EDIT. Effect: DO NOT EDIT Evidence: ledger:E0371, ledger:E0899, ledger:E1151, ledger:E1408</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>gain</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="Gain 1" />
      <LABEL index="1" value="Gain 2" />
      <LABEL index="2" value="Gain 3" />
      <LABEL index="3" value="Gain 4" />
      <LABEL index="4" value="Gain 5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23BC8" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1DC" flags="0x30">
    <title>EVAP Leak Test Vacuum Decay Limit - Low Range</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP leak test, vacuum hold phase: the PCM seals the EVAP system under vacuum and measures how fast tank vacuum decays (the decay slope it reports on PID 1296). A slope above this limit fails the test. Rows cover the lower half of the EVAP vapour reference, which the PCM derives from fuel level (the row labels give the fuel level on stock settings, n/a = not reached); columns are intake air temperature 0 to 40 C. Stock 0.039 inH2O per second in every cell. Raising it lets a faster leak pass. Not used by the stock calibration: this belongs to the engine-running small leak phase, which the stock calibration switches off (small...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC (IAT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1.25" />
      <LABEL index="2" value="2.5" />
      <LABEL index="3" value="3.75" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6.25" />
      <LABEL index="6" value="7.5" />
      <LABEL index="7" value="8.75" />
      <LABEL index="8" value="10" />
      <LABEL index="9" value="11.25" />
      <LABEL index="10" value="12.5" />
      <LABEL index="11" value="13.75" />
      <LABEL index="12" value="15" />
      <LABEL index="13" value="16.25" />
      <LABEL index="14" value="17.5" />
      <LABEL index="15" value="18.75" />
      <LABEL index="16" value="20" />
      <LABEL index="17" value="21.25" />
      <LABEL index="18" value="22.5" />
      <LABEL index="19" value="23.75" />
      <LABEL index="20" value="25" />
      <LABEL index="21" value="26.25" />
      <LABEL index="22" value="27.5" />
      <LABEL index="23" value="28.75" />
      <LABEL index="24" value="30" />
      <LABEL index="25" value="31.25" />
      <LABEL index="26" value="32.5" />
      <LABEL index="27" value="33.75" />
      <LABEL index="28" value="35" />
      <LABEL index="29" value="36.25" />
      <LABEL index="30" value="37.5" />
      <LABEL index="31" value="38.75" />
      <LABEL index="32" value="40" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>% fuel level (stock settings)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="n/a" />
      <LABEL index="1" value="95" />
      <LABEL index="2" value="77" />
      <LABEL index="3" value="59" />
      <LABEL index="4" value="41" />
      <LABEL index="5" value="23" />
      <LABEL index="6" value="4" />
      <LABEL index="7" value="n/a" />
      <LABEL index="8" value="n/a" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3589A" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>inH2O/s</units>
      <decimalpl>3</decimalpl>
      <min>-8.000000</min>
      <max>7.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1DD" flags="0x30">
    <title>EVAP Leak Test Vacuum Decay Limit - High Range</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP leak test, vacuum hold phase: the PCM seals the EVAP system under vacuum and measures how fast tank vacuum decays (the decay slope it reports on PID 1296). A slope above this limit fails the test. Rows cover the upper half of the EVAP vapour reference, which the PCM derives from fuel level (the row labels give the fuel level on stock settings, n/a = not reached); columns are intake air temperature 0 to 40 C. Stock 0.039 inH2O per second in every cell. Raising it lets a faster leak pass. Not used by the stock calibration: this belongs to the engine-running small leak phase, which the stock calibration switches off (small...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC (IAT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1.25" />
      <LABEL index="2" value="2.5" />
      <LABEL index="3" value="3.75" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6.25" />
      <LABEL index="6" value="7.5" />
      <LABEL index="7" value="8.75" />
      <LABEL index="8" value="10" />
      <LABEL index="9" value="11.25" />
      <LABEL index="10" value="12.5" />
      <LABEL index="11" value="13.75" />
      <LABEL index="12" value="15" />
      <LABEL index="13" value="16.25" />
      <LABEL index="14" value="17.5" />
      <LABEL index="15" value="18.75" />
      <LABEL index="16" value="20" />
      <LABEL index="17" value="21.25" />
      <LABEL index="18" value="22.5" />
      <LABEL index="19" value="23.75" />
      <LABEL index="20" value="25" />
      <LABEL index="21" value="26.25" />
      <LABEL index="22" value="27.5" />
      <LABEL index="23" value="28.75" />
      <LABEL index="24" value="30" />
      <LABEL index="25" value="31.25" />
      <LABEL index="26" value="32.5" />
      <LABEL index="27" value="33.75" />
      <LABEL index="28" value="35" />
      <LABEL index="29" value="36.25" />
      <LABEL index="30" value="37.5" />
      <LABEL index="31" value="38.75" />
      <LABEL index="32" value="40" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>% fuel level (stock settings)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="n/a" />
      <LABEL index="1" value="n/a" />
      <LABEL index="2" value="n/a" />
      <LABEL index="3" value="n/a" />
      <LABEL index="4" value="n/a" />
      <LABEL index="5" value="n/a" />
      <LABEL index="6" value="n/a" />
      <LABEL index="7" value="n/a" />
      <LABEL index="8" value="n/a" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35AF2" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>inH2O/s</units>
      <decimalpl>3</decimalpl>
      <min>-8.000000</min>
      <max>7.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1DE" flags="0x30">
    <title>Exhaust Temperature Model - Power-Up Restore vs Engine-Off Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At power-up the catalyst channel of the exhaust temperature model restarts from the modelled temperature it held at shutdown (rows), decayed by how long the engine was off (columns, 0 to 9600 s in 5 minute steps); the other two channels restart at 0. Column 0 returns the row temperature and every row decays toward 0 with a time constant of about 33 minutes. The model is read only by diagnostics (catalyst monitor conditions, a diagnostic timer and secondary air), not by fuel, spark, torque or throttle. If the engine-off timer has failed its own check (P2610), the engine-off time is taken as 0, so the shutdown temperature is re...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>s (engine-off time)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="300" />
      <LABEL index="2" value="600" />
      <LABEL index="3" value="900" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1500" />
      <LABEL index="6" value="1800" />
      <LABEL index="7" value="2100" />
      <LABEL index="8" value="2400" />
      <LABEL index="9" value="2700" />
      <LABEL index="10" value="3000" />
      <LABEL index="11" value="3300" />
      <LABEL index="12" value="3600" />
      <LABEL index="13" value="3900" />
      <LABEL index="14" value="4200" />
      <LABEL index="15" value="4500" />
      <LABEL index="16" value="4800" />
      <LABEL index="17" value="5100" />
      <LABEL index="18" value="5400" />
      <LABEL index="19" value="5700" />
      <LABEL index="20" value="6000" />
      <LABEL index="21" value="6300" />
      <LABEL index="22" value="6600" />
      <LABEL index="23" value="6900" />
      <LABEL index="24" value="7200" />
      <LABEL index="25" value="7500" />
      <LABEL index="26" value="7800" />
      <LABEL index="27" value="8100" />
      <LABEL index="28" value="8400" />
      <LABEL index="29" value="8700" />
      <LABEL index="30" value="9000" />
      <LABEL index="31" value="9300" />
      <LABEL index="32" value="9600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC (modelled catalyst temperature at shutdown)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="200" />
      <LABEL index="1" value="250" />
      <LABEL index="2" value="300" />
      <LABEL index="3" value="350" />
      <LABEL index="4" value="400" />
      <LABEL index="5" value="450" />
      <LABEL index="6" value="500" />
      <LABEL index="7" value="550" />
      <LABEL index="8" value="600" />
      <LABEL index="9" value="650" />
      <LABEL index="10" value="700" />
      <LABEL index="11" value="750" />
      <LABEL index="12" value="800" />
      <LABEL index="13" value="850" />
      <LABEL index="14" value="900" />
      <LABEL index="15" value="950" />
      <LABEL index="16" value="1000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3388C" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1023.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1DF" flags="0x0">
    <title>TCC Adapt - Min Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. TCC adapt only learns above this trans temp (stock 40 C). Part of TCC adaptive learning: while the converter clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells across 50..210 Nm (E0376). Effect: TCC adaptive learning Evidence: ledger:E0376</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CD94" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E0" flags="0x0">
    <title>TCC Adapt - Max Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. TCC adapt only learns below this trans temp (stock 120 C). Part of TCC adaptive learning: while the converter clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells across 50..210 Nm (E0376). Effect: TCC adaptive learning Evidence: ledger:E0376</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CD96" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E1" flags="0x0">
    <title>TCC Adapt - Min Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. TCC adapt only learns above this trans-side speed (stock 16.2 km/h). Part of TCC adaptive learning: while the converter clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells across 50..210 Nm (E0376). Effect: TCC adaptive learning Evidence: ledger:E0376</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CD8E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E2" flags="0x0">
    <title>TCC Adapt - Max Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. TCC adapt only learns below this trans-side speed (stock 321 km/h). Part of TCC adaptive learning: while the converter clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells across 50..210 Nm (E0376). Effect: TCC adaptive learning Evidence: ledger:E0376</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CD90" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E3" flags="0x0">
    <title>TCC Adapt - Min Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. TCC adapt only learns above this throttle area (stock 2.5 %). Part of TCC adaptive learning: while the converter clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells across 50..210 Nm (E0376). Effect: TCC adaptive learning Evidence: ledger:E0376</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CD9E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E4" flags="0x0">
    <title>TCC Adapt - Max Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. TCC adapt only learns below this throttle area (stock 100 %). Part of TCC adaptive learning: while the converter clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells across 50..210 Nm (E0376). Effect: TCC adaptive learning Evidence: ledger:E0376</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CDA0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E5" flags="0x0">
    <title>TCC Adapt - Max Torque Change</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learning stops while torque differs from its filtered value by more than this (stock 13.5 Nm). Part of TCC adaptive learning: while the converter clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells across 50..210 Nm (E0376). Effect: TCC adaptive learning Evidence: ledger:E0376</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CDAA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E6" flags="0x0">
    <title>TCC Adapt - Max Throttle Change</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learning stops while throttle differs from its filtered value by more than this (stock 2.0 %). Part of TCC adaptive learning: while the converter clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells across 50..210 Nm (E0376). Effect: TCC adaptive learning Evidence: ledger:E0376</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CDA4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E7" flags="0x0">
    <title>TCC Adapt - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Conditions must hold this long before learning starts (stock 2.0 s). Part of TCC adaptive learning: while the converter clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells across 50..210 Nm (E0376). Effect: TCC adaptive learning Evidence: ledger:E0376</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CDAC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E8" flags="0x0">
    <title>TCC Adapt - Learn Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time between learn updates once settled (stock 1.0 s). Part of TCC adaptive learning: while the converter clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells across 50..210 Nm (E0376). Effect: TCC adaptive learning Evidence: ledger:E0376</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CDAE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E9" flags="0x0">
    <title>TCC Adapt - Max Controller Change</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learning holds off while the slip controller pressure term differs from its filtered value by more than this (stock 6.9 kPa). Part of converter clutch adaptive learning: while the clutch is applied and conditions are steady, the PCM learns a pressure offset in five cells across 50 to 210 Nm and adds it to the load based clutch pressure. Effect: raise = learning also runs while the controller is still moving Evidence: ledger:E0376, ledger:E1432</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CD8C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>2047.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1EA" flags="0x0">
    <title>TCC Adapt - Max Slip Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While the torque converter clutch is locked up and driving conditions are steady, the PCM slowly learns a small correction to how it controls the clutch. Learning pauses whenever the actual clutch slip is off from its target by more than this amount. Stock 15 rpm. Effect: raise = learning keeps working through a bigger slip error before it pauses Evidence: ledger:E0376, ledger:E0797</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CD92" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1EB" flags="0x0">
    <title>TCC Adapt - Cell Lower Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest value a learned pressure offset may take (stock -620 kPa). Part of converter clutch adaptive learning: while the clutch is applied and conditions are steady, the PCM learns a pressure offset in five cells across 50 to 210 Nm and adds it to the load based clutch pressure. Effect: lower = the learned offset may go further negative Evidence: ledger:E0376, ledger:E1432</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CD86" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1EC" flags="0x0">
    <title>TCC Adapt - Cell Upper Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest value a learned pressure offset may take (stock 620 kPa). Part of converter clutch adaptive learning: while the clutch is applied and conditions are steady, the PCM learns a pressure offset in five cells across 50 to 210 Nm and adds it to the load based clutch pressure. Effect: raise = the learned offset may go further positive Evidence: ledger:E0376, ledger:E1432</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CD88" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1ED" flags="0x30">
    <title>Engine Torque Estimate vs Throttle x RPM (throttle-based model)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Gross torque the PCM predicts from throttle area and rpm, before the baro and intake air temperature multipliers and minus losses and inertia; the electronic throttle&#x27;s torque control and others read it. Rows are the total throttle area request (idle plus pedal), in % of full throttle area. Stock 0 at closed throttle up to 400 Nm. Model: do not edit to change power. Effect: DO NOT EDIT (torque model) Evidence: ledger:E0377, ledger:E0452, ledger:E0927, ledger:E0936</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8191" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>% throttle area</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="0.2" />
      <LABEL index="2" value="0.4" />
      <LABEL index="3" value="0.6" />
      <LABEL index="4" value="0.8" />
      <LABEL index="5" value="1.0" />
      <LABEL index="6" value="1.2" />
      <LABEL index="7" value="1.4" />
      <LABEL index="8" value="1.6" />
      <LABEL index="9" value="1.8" />
      <LABEL index="10" value="2.0" />
      <LABEL index="11" value="2.5" />
      <LABEL index="12" value="3.0" />
      <LABEL index="13" value="3.5" />
      <LABEL index="14" value="4.0" />
      <LABEL index="15" value="5.0" />
      <LABEL index="16" value="6.0" />
      <LABEL index="17" value="7.0" />
      <LABEL index="18" value="8.0" />
      <LABEL index="19" value="9.0" />
      <LABEL index="20" value="10.0" />
      <LABEL index="21" value="12.0" />
      <LABEL index="22" value="14.0" />
      <LABEL index="23" value="16.0" />
      <LABEL index="24" value="18.0" />
      <LABEL index="25" value="20.0" />
      <LABEL index="26" value="25.0" />
      <LABEL index="27" value="30.0" />
      <LABEL index="28" value="35.0" />
      <LABEL index="29" value="40.0" />
      <LABEL index="30" value="45.0" />
      <LABEL index="31" value="50.0" />
      <LABEL index="32" value="100.0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30EFE" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1EE" flags="0x30">
    <title>Engine Torque Estimate - RPM Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stored rpm breakpoints of the throttle-based torque estimate table: 0 to 7680 rpm in 512 rpm steps, then 8191. Effect: moves the axis of every table that uses it: edit with care Evidence: ledger:E0377</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30E8E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1EF" flags="0x30">
    <title>Engine Torque Estimate - Throttle Breakpoints (raw, DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle breakpoints of the throttle-based engine torque estimate table: 33 stored points, non-uniform from 0, then an end marker. The torque estimate feeds shift pressure, torque reduction, converter clutch and throttle torque control. Shown raw. DO NOT EDIT. Effect: DO NOT EDIT Evidence: ledger:E0377, ledger:E0899, ledger:E1151</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30EB4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1F0" flags="0x0">
    <title>Idle Moving Mode and First Idle After Start - Speed Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed that splits stopped from moving for the idle controller. Above it the controller is in its moving mode: the idle airflow integral may run and closed loop idle speed control stays off. At or below it, the first idle after a start ends when rpm falls to desired idle (plus the offset); above it only the airflow test applies. Stock 17.5 km/h. Effect: raise = the truck counts as stopped for idle control up to a higher speed Evidence: ledger:E0378, ledger:E1103</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29740" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1F1" flags="0x0">
    <title>First Idle After Start - End RPM Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The first-idle settings end once rpm is at or below desired idle plus this. Stock 0 rpm. Effect: raise = first-idle settings end sooner Evidence: ledger:E0378</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A9A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1F2" flags="0x0">
    <title>First Idle After Start - End Airflow Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above the speed threshold, the first-idle settings end when predicted idle airflow plus this exceeds a limit. Stock -32 g/s (off). Effect: raise toward 0 to enable the airflow test Evidence: ledger:E0378</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A9A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1F3" flags="0x30">
    <title>A/C Idle Air - Target vs A/C Compressor Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air added for the A/C compressor, by A/C compressor torque (0 to 80 Nm). The value is multiplied by an rpm factor that is 0.125 at every engine speed on stock; the scaling shown includes that factor. Stock 0.5 to 3.0 g/s. Effect: raise = more idle air with the A/C on Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>Nm A/C compressor torque</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29F22" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>0</decimalpl>
      <min>-4.000000</min>
      <max>3.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1F4" flags="0x30">
    <title>A/C Idle Air Ramp-In Step vs A/C Compressor Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added per update while the A/C idle air ramps in when the compressor engages, by A/C compressor torque (0 to 80 Nm), until the A/C idle air target is reached. Stock 0.9 down to 0.5 g/s. Effect: raise = the extra idle air for the A/C comes in faster Evidence: ledger:E0379, ledger:E0948</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>Nm (A/C compressor torque)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29F0E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s per update</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1F5" flags="0x30">
    <title>A/C Idle Air Sequence Hold Time vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the A/C idle air sequence holds after the air has ramped in before it ends, by engine speed (0 to 4096 rpm). Stock 1.3 s at low rpm down to 0.16 s. Effect: raise = the A/C idle air sequence stays active longer Evidence: ledger:E0379, ledger:E0936, ledger:E0948</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29F5A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1F6" flags="0x0">
    <title>Rear O2 Trim - Region Boundary, High Airflow / Fifth Region</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: airflow position above which the fifth region is used instead of the high airflow region. Stock 8.0, the end of the scale: the fifth region is never used. Positions are columns of the O2 switch point base curve (see O2 Switch Point Airflow Map). Regions: closed throttle idle, low, mid and high airflow, and a fifth region that stock never reaches. Effect: lower = the fifth region takes over at high airflow Evidence: ledger:E1107</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2579E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>base column</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1F7" flags="0x0">
    <title>Rear O2 Trim - Region Boundary, Low / Mid Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: airflow position up to which the low airflow region is used. Stock 1.75 (about 7 g/s on the stock airflow map). Positions are columns of the O2 switch point base curve (see O2 Switch Point Airflow Map). Regions: closed throttle idle, low, mid and high airflow, and a fifth region that stock never reaches. Effect: raise = the low airflow region reaches higher airflow Evidence: ledger:E1107</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x257A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>base column</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1F8" flags="0x0">
    <title>Rear O2 Trim - Region Boundary, Mid / High Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: airflow position up to which the mid airflow region is used. Stock 3.5 (about 17 g/s on the stock airflow map). Positions are columns of the O2 switch point base curve (see O2 Switch Point Airflow Map). Regions: closed throttle idle, low, mid and high airflow, and a fifth region that stock never reaches. Effect: raise = the mid airflow region reaches higher airflow Evidence: ledger:E1107</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x257A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>base column</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1F9" flags="0x0">
    <title>STFT Tip-In Reset Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: at a low speed tip-in (throttle request rising through its tip-in threshold), a trim integrator below this is reset to 1.0, so a fuel-removing trim is dropped as the throttle opens. Stock 1.0. Effect: lower = only a larger fuel-removing trim is reset at tip-in Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25950" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1FA" flags="0x0">
    <title>STFT Purge-Off Reset Threshold (Fuel Trim Monitor)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: when the fuel trim monitor shuts canister purge off, a trim integrator below this is set back to 1.0 on that pass, so a fuel-removing trim learned with purge flowing is dropped. Stock 1.0. Effect: lower = a fuel-removing trim is kept when the monitor shuts purge off Evidence: ledger:E1126</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x364A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1FB" flags="0x30">
    <title>TCC Feed-Forward - Rising Torque Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Gain on the rising torque feed-forward pull back, by the rate of change (0 to 98 Nm/s). Stock 0.75 at 0 Nm/s, 0.90 at 20 Nm/s, 1.0 from 39 Nm/s. Part of the converter clutch slip controller&#x27;s feed-forward: while engine torque rises faster than the rise threshold, if clutch pressure is climbing faster than the allowed rise for that torque increase, the controller pulls the pressure back by the excess (times the rising gain). Effect: lower = less extra apply when torque rises at that rate Evidence: ledger:E0373, ledger:E0384, ledger:E1201, ledger:E1471</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3CE94" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>5</indexcount>
      <units>Nm/s (engine torque rate)</units>
      <embedinfo type="1" />
      <MATH equation="X/32.768"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CEA0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1FC" flags="0x30">
    <title>TCC Feed-Forward - Falling Torque Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Gain on the torque converter clutch slip controller&#x27;s feed-forward while engine torque falls, by the rate of change (0 to 98 Nm/s). Stock 0.75 at 0 Nm/s, 0.90 at 20 Nm/s, 1.0 from 39 Nm/s. The falling-torque feed-forward table it multiplies is 0 everywhere in the stock calibration. Effect: lower = less feed-forward when torque falls at that rate Evidence: ledger:E0373, ledger:E0384, ledger:E1201</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3CE94" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>5</indexcount>
      <units>Nm/s (engine torque rate)</units>
      <embedinfo type="1" />
      <MATH equation="X/32.768"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CEB8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1FD" flags="0x0">
    <title>TCC Feed-Forward - Rise Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The converter clutch slip controller applies its rising torque feed-forward only when engine torque is rising faster than this. Stock 39 Nm/s. Part of the converter clutch slip controller&#x27;s feed-forward: while engine torque rises faster than the rise threshold, if clutch pressure is climbing faster than the allowed rise for that torque increase, the controller pulls the pressure back by the excess (times the rising gain). Effect: lower = the feed-forward starts on gentler torque rises Evidence: ledger:E0384, ledger:E1201, ledger:E1471</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D182" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>1999.969482</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32.768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1FE" flags="0x30">
    <title>Ambient Air Temp Estimate - Intake Heat Rise vs Airflow x Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The ambient temperature estimate (PID 0x46) targets IAT minus this rise; only updated above 5 g/s and 48 km/h. Stock 50 C at standstill, 7.5 C at 80 km/h, about 4 C at 160 km/h (E0385). Effect: raise = lower ambient estimate Evidence: ledger:E0385, ledger:E0936</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <LABEL index="11" value="110" />
      <LABEL index="12" value="120" />
      <LABEL index="13" value="130" />
      <LABEL index="14" value="140" />
      <LABEL index="15" value="150" />
      <LABEL index="16" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="8" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="24" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="48" />
      <LABEL index="7" value="56" />
      <LABEL index="8" value="64" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="88" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="104" />
      <LABEL index="14" value="112" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x342D4" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1FF" flags="0x30">
    <title>Ambient Air Temp Estimate - Step per Update vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How far the ambient estimate moves toward its target each update. Stock 0.1 C at every airflow (E0385). Effect: raise = ambient estimate follows faster Evidence: ledger:E0385</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="8" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="24" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="48" />
      <LABEL index="7" value="56" />
      <LABEL index="8" value="64" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="88" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="104" />
      <LABEL index="14" value="112" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34282" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x200" flags="0x30">
    <title>Spark Ceiling - Hot Mode Ceiling vs Airmass x RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The lower spark ceiling used by the hot high-load mode: after the hot, high-rpm, high-load condition lasts the arm time, spark above this value is pulled back (blended in by the ramp-in curve). Also the level at which the blend starts. Stock 18 deg to 1536 rpm rising to 24 deg from 6656 rpm, the same in every airmass row. Effect: raise = blend engages at higher spark Evidence: ledger:E0386, ledger:E0719</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>g/cyl (airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.16" />
      <LABEL index="2" value="0.24" />
      <LABEL index="3" value="0.32" />
      <LABEL index="4" value="0.4" />
      <LABEL index="5" value="0.48" />
      <LABEL index="6" value="0.56" />
      <LABEL index="7" value="0.64" />
      <LABEL index="8" value="0.72" />
      <LABEL index="9" value="0.8" />
      <LABEL index="10" value="0.88" />
      <LABEL index="11" value="0.96" />
      <LABEL index="12" value="1.04" />
      <LABEL index="13" value="1.12" />
      <LABEL index="14" value="1.2" />
      <LABEL index="15" value="1.28" />
      <LABEL index="16" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2FF1A" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x201" flags="0x30">
    <title>Spark Limit Blend - Ramp-In Step vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot high-load spark ceiling blend (E0719). Blend added per update (fraction of full = X/128). Stock 0.09 cold to 0.26 hot (E0386). Effect: raise = limit engages faster Evidence: ledger:E0386, ledger:E0719</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3026A" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x202" flags="0x30">
    <title>Spark Limit Blend - Ramp-Out Step vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot high-load spark ceiling blend (E0719). Blend removed per update (fraction of full = X/128). Stock 0.09 cold to 0.26 hot (E0386). Effect: raise = limit releases faster Evidence: ledger:E0386, ledger:E0719</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3027D" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x203" flags="0x30">
    <title>Shift Speed vs TPS - Mode 0</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0387). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Full shift schedule used in shift mode 0. Rows in slot order. Read through the shift schedule pointer table. Effect: raise = hold gears longer; keep each downshift below its upshift (hysteresis) Evidence: ledger:E0176, ledger:E0180, ledger:E0208, ledger:E0269, ledger:E0387, ledger:E0705, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2 up" />
      <LABEL index="1" value="2-1 down" />
      <LABEL index="2" value="2-3 up" />
      <LABEL index="3" value="3-2 down" />
      <LABEL index="4" value="3-4 up" />
      <LABEL index="5" value="4-3 down" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39CCE" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x204" flags="0x30">
    <title>Shift Speed vs TPS - Mode 1 Upshifts</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0387). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upshift curves used in shift mode 1; its downshifts share the hot schedule&#x27;s curves. Read through the shift schedule pointer table. Effect: raise = hold gears longer; keep each downshift below its upshift (hysteresis) Evidence: ledger:E0176, ledger:E0180, ledger:E0208, ledger:E0269, ledger:E0387, ledger:E0705, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2 up" />
      <LABEL index="1" value="2-3 up" />
      <LABEL index="2" value="3-4 up" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39C62" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x205" flags="0x30">
    <title>Shift Speed - 2nd Gear Max, Locked Upper Shifts (2-point)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 2][2 points]; COUNT is a structure word, never edit it (E0387). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper shifts in the 2nd-max records: upshifts at 311 mph and downshifts at 307.6 mph, i.e. never shifts above 2nd. Read through the shift schedule pointer table. Effect: raise = hold gears longer; keep each downshift below its upshift (hysteresis) Evidence: ledger:E0176, ledger:E0180, ledger:E0208, ledger:E0269, ledger:E0387, ledger:E0705, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2-3 up" />
      <LABEL index="1" value="3-4 up" />
      <LABEL index="2" value="3-2 down" />
      <LABEL index="3" value="4-3 down" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39794" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x206" flags="0x30">
    <title>Shift Speed vs TPS - 3rd Gear Max (range column 2), 3-4 / 4-3</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0387). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 3-4 slots of the 3rd-max records k4 / k10 / k15 / k21 (hot / cruise / performance / normal): 3-4 at 311 mph (never). Read through the shift schedule pointer table. Effect: raise = hold gears longer; keep each downshift below its upshift (hysteresis) Evidence: ledger:E0176, ledger:E0180, ledger:E0208, ledger:E0269, ledger:E0387, ledger:E0705, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="3-4 up" />
      <LABEL index="1" value="4-3 down" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39884" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x207" flags="0x30">
    <title>WOT Shift Speed vs Shift - Cruise (Set 1)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 2][2 points]; COUNT is a structure word, never edit it (E0387). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. WOT shift speeds (shift mode 4, E0180). Read through the shift schedule pointer table. Effect: raise = hold gears longer; keep each downshift below its upshift (hysteresis) Evidence: ledger:E0176, ledger:E0180, ledger:E0208, ledger:E0269, ledger:E0387, ledger:E0705, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2 up" />
      <LABEL index="1" value="2-3 up" />
      <LABEL index="2" value="3-4 up" />
      <LABEL index="3" value="2-1 down" />
      <LABEL index="4" value="3-2 down" />
      <LABEL index="5" value="4-3 down" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x399DA" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x208" flags="0x30">
    <title>WOT Shift RPM - Cruise (Set 1)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 2][2 points]; COUNT is a structure word, never edit it (E0387). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. WOT upshift rpm rows ; stock 6100 rpm. Read through the shift schedule pointer table. Effect: raise = hold gears longer; keep each downshift below its upshift (hysteresis) Evidence: ledger:E0176, ledger:E0180, ledger:E0208, ledger:E0269, ledger:E0387, ledger:E0705, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x399FE" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X*0.125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x209" flags="0x30">
    <title>WOT Shift Speed vs Shift - Cruise (Set 2)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 2][2 points]; COUNT is a structure word, never edit it (E0387). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. WOT shift speeds (shift mode 5, E0180). Read through the shift schedule pointer table. Effect: raise = hold gears longer; keep each downshift below its upshift (hysteresis) Evidence: ledger:E0176, ledger:E0180, ledger:E0208, ledger:E0269, ledger:E0387, ledger:E0705, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2 up" />
      <LABEL index="1" value="2-3 up" />
      <LABEL index="2" value="3-4 up" />
      <LABEL index="3" value="2-1 down" />
      <LABEL index="4" value="3-2 down" />
      <LABEL index="5" value="4-3 down" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39B1E" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x20A" flags="0x30">
    <title>WOT Shift RPM - Cruise (Set 2)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 2][2 points]; COUNT is a structure word, never edit it (E0387). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. WOT upshift rpm rows ; stock 6100 rpm. Read through the shift schedule pointer table. Effect: raise = hold gears longer; keep each downshift below its upshift (hysteresis) Evidence: ledger:E0176, ledger:E0180, ledger:E0208, ledger:E0269, ledger:E0387, ledger:E0705, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39B42" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X*0.125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x20B" flags="0x30">
    <title>ETC Engine Speed Limiter - Base Torque vs RPM x Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base torque of the throttle-side engine speed limiter, by engine speed (rows) and throttle (columns). The limiter engages above about 1100 rpm with the pedal released; its torque limit is this value plus a proportional and integral correction on engine speed error (reference at least 900 rpm), and it replaces the engine torque request whenever it is lower. Stock 0 Nm at zero throttle below 1500 rpm, down to -500 Nm above, 80 to 175 Nm at the first throttle steps and 250 Nm from about 3 % throttle. Effect: raise = higher engine torque allowed when the throttle-side engine speed limiter starts acting Evidence: ledger:E0388, led...</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% throttle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1.562" />
      <LABEL index="2" value="3.125" />
      <LABEL index="3" value="4.688" />
      <LABEL index="4" value="6.25" />
      <LABEL index="5" value="7.812" />
      <LABEL index="6" value="9.375" />
      <LABEL index="7" value="10.938" />
      <LABEL index="8" value="12.5" />
      <LABEL index="9" value="14.062" />
      <LABEL index="10" value="15.625" />
      <LABEL index="11" value="17.188" />
      <LABEL index="12" value="18.75" />
      <LABEL index="13" value="20.312" />
      <LABEL index="14" value="21.875" />
      <LABEL index="15" value="23.438" />
      <LABEL index="16" value="25" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="500" />
      <LABEL index="1" value="1000" />
      <LABEL index="2" value="1500" />
      <LABEL index="3" value="2000" />
      <LABEL index="4" value="2500" />
      <LABEL index="5" value="3000" />
      <LABEL index="6" value="3500" />
      <LABEL index="7" value="4000" />
      <LABEL index="8" value="4500" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23C9A" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x20C" flags="0x30">
    <title>Airflow Rationality - Engine Airflow Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101), diagnostic model only: multiplier on the engine airflow the two manifold pressure models assume, by engine speed (400 to 6400 rpm) and barometric pressure (55 to 105 kPa). Stock 1.0 everywhere. Effect: raise = the models assume the engine draws more air at that speed and barometric pressure Evidence: ledger:E0388, ledger:E1074</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="775" />
      <LABEL index="2" value="1150" />
      <LABEL index="3" value="1525" />
      <LABEL index="4" value="1900" />
      <LABEL index="5" value="2275" />
      <LABEL index="6" value="2650" />
      <LABEL index="7" value="3025" />
      <LABEL index="8" value="3400" />
      <LABEL index="9" value="3775" />
      <LABEL index="10" value="4150" />
      <LABEL index="11" value="4525" />
      <LABEL index="12" value="4900" />
      <LABEL index="13" value="5275" />
      <LABEL index="14" value="5650" />
      <LABEL index="15" value="6025" />
      <LABEL index="16" value="6400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="55" />
      <LABEL index="1" value="61.25" />
      <LABEL index="2" value="67.5" />
      <LABEL index="3" value="73.75" />
      <LABEL index="4" value="80" />
      <LABEL index="5" value="86.25" />
      <LABEL index="6" value="92.5" />
      <LABEL index="7" value="98.75" />
      <LABEL index="8" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x365D6" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x20D" flags="0x30">
    <title>TCC Apply / Release Speed vs TPS - Mode 0 and Mode 1</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0389). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. TCC apply and release speeds for shift mode 0 (all rows) and the apply rows of mode 1 (its release rows are the hot table&#x27;s). Read through the TCC schedule pointer table. Effect: raise apply = lock up later; keep each release below its apply Evidence: ledger:E0177, ledger:E0180, ledger:E0208, ledger:E0269, ledger:E0389, ledger:E0705, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="Mode 0 2nd apply" />
      <LABEL index="1" value="Mode 0 3rd apply" />
      <LABEL index="2" value="Mode 0 4th apply" />
      <LABEL index="3" value="Mode 1 2nd apply" />
      <LABEL index="4" value="Mode 1 3rd apply" />
      <LABEL index="5" value="Mode 1 4th apply" />
      <LABEL index="6" value="Mode 0 2nd release" />
      <LABEL index="7" value="Mode 0 3rd release" />
      <LABEL index="8" value="Mode 0 4th release" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D50E" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x20E" flags="0x30">
    <title>TCC WOT Apply / Release Speed (Set 1)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 2][2 points]; COUNT is a structure word, never edit it (E0389). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. WOT TCC speeds (shift mode 4, range column 2). Read through the TCC schedule pointer table. Effect: raise apply = lock up later; keep each release below its apply Evidence: ledger:E0177, ledger:E0180, ledger:E0208, ledger:E0269, ledger:E0389, ledger:E0705, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd apply" />
      <LABEL index="1" value="3rd apply" />
      <LABEL index="2" value="4th apply" />
      <LABEL index="3" value="2nd release" />
      <LABEL index="4" value="3rd release" />
      <LABEL index="5" value="4th release" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D652" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x20F" flags="0x30">
    <title>TCC WOT Apply / Release Speed (Set 2)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 2][2 points]; COUNT is a structure word, never edit it (E0389). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. WOT TCC speeds (shift mode 5, range column 2). Read through the TCC schedule pointer table. Effect: raise apply = lock up later; keep each release below its apply Evidence: ledger:E0177, ledger:E0180, ledger:E0208, ledger:E0269, ledger:E0389, ledger:E0705, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd apply" />
      <LABEL index="1" value="3rd apply" />
      <LABEL index="2" value="4th apply" />
      <LABEL index="3" value="2nd release" />
      <LABEL index="4" value="3rd release" />
      <LABEL index="5" value="4th release" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D946" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x210" flags="0x30">
    <title>TCC Apply / Release Speed vs TPS - 2nd Gear Max, Hot</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0389). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 2nd-gear TCC rows while the range caps at 2nd (range column 1), hot modes; 3rd / 4th rows are the hot table&#x27;s. Read through the TCC schedule pointer table. The PCM uses the Hot schedules while hot transmission mode is on; hot mode takes priority over cruise and 4-Lo. Effect: raise apply = lock up later; keep each release below its apply Evidence: ledger:E0177, ledger:E0180, ledger:E0208, ledger:E0269, ledger:E0389, ledger:E0705, ledger:E0838, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd apply" />
      <LABEL index="1" value="2nd release" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D772" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x211" flags="0x30">
    <title>TCC Apply / Release Speed vs TPS - 2nd Gear Max, Normal</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0389). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 2nd-gear TCC rows while the range caps at 2nd, normal modes 4 / 9 / 10. Read through the TCC schedule pointer table. The PCM uses the Normal schedules in ordinary driving: not in hot transmission mode, cruise or 4-Lo. Effect: raise apply = lock up later; keep each release below its apply Evidence: ledger:E0177, ledger:E0180, ledger:E0208, ledger:E0269, ledger:E0389, ledger:E0705, ledger:E0838, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd apply" />
      <LABEL index="1" value="2nd release" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D8B6" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x212" flags="0x30">
    <title>TCC Apply / Release Speed vs TPS - Range Column 0</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0389). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. TCC rows for range column 0 (the 1st-hold range, ): only 2nd-gear rows exist, 3rd / 4th pointers are null. Read through the TCC schedule pointer table. Effect: raise apply = lock up later; keep each release below its apply Evidence: ledger:E0177, ledger:E0180, ledger:E0208, ledger:E0269, ledger:E0389, ledger:E0705, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd apply" />
      <LABEL index="1" value="2nd release" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D8FE" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x213" flags="0x30">
    <title>TCC Apply / Release Speed vs TPS - 2nd Gear Max, Cruise</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0389). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 2nd-gear TCC rows while the range caps at 2nd, cruise modes 5 / 6. Read through the TCC schedule pointer table. The PCM uses the Cruise schedules while cruise control is engaged; cruise takes priority over 4-Lo. Effect: raise apply = lock up later; keep each release below its apply Evidence: ledger:E0177, ledger:E0180, ledger:E0208, ledger:E0269, ledger:E0389, ledger:E0705, ledger:E0838, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd apply" />
      <LABEL index="1" value="2nd release" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DA42" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x214" flags="0x30">
    <title>TCC Apply / Release Speed vs TPS - 2nd Gear Max, 4-Lo</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0389). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 2nd-gear TCC rows while the range caps at 2nd, 4-Lo (modes 7 / 8). Read through the TCC schedule pointer table. The PCM uses these schedules while the transfer case is in 4-Lo (named Performance before v3.7; the stock calibration has no separate performance mode). In 4-Lo the transmission&#x27;s speed reading is 4.03 times road speed (it is worked out from transmission output speed with the high-range ratio), so a value of 40 km/h here acts at about 10 km/h on the road. Effect: raise apply = lock up later; keep each release below its ap...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd apply" />
      <LABEL index="1" value="2nd release" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DB86" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x215" flags="0x30">
    <title>Pedal to Throttle-Area Demand - Slot k7 (not used on the H3)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: which transmission state uses this map is set by a pedal mode 2 selector that is not in this file; the stock selection on this calibration can differ from the H3 described below. A populated pedal map (pedal % by vehicle speed to throttle-area demand) in a slot that no mode selects on the H3, so editing it has no effect on this truck. Effect: no effect on the stock H3 Evidence: ledger:E0228, ledger:E0232, ledger:E0240, ledger:E0391</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x24B76" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x24B9A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24886" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x216" flags="0x30">
    <title>Coolant Temp Sensor - Temperature Points</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Temperature at each of the 33 sensor resistance points (stock 150 C down to -40 C in 5.9 C steps); the PCM interpolates between them to get coolant temperature. Effect: reported and used coolant temperature Evidence: ledger:E0392, ledger:E1047</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x228CC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x217" flags="0x30">
    <title>Shift Pressure Phase - Start Ratio (torque band 0)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0393). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start ratio for torque band state 0 (below the E0350 net-torque threshold); stock 3.000 / 1.625 / 1.000. Ratio points of the shift pressure phase (measured gear ratio): the phase ramps its pressure in between start and full and out by end. On the stock H3 the phase pressure curves are all zero, so these only matter if those are filled (E0393). Effect: shift pressure phase timing Evidence: ledger:E0393, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="120" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="200" />
      <LABEL index="7" value="240" />
      <LABEL index="8" value="280" />
      <LABEL index="9" value="320" />
      <LABEL index="10" value="360" />
      <LABEL index="11" value="400" />
      <LABEL index="12" value="440" />
      <LABEL index="13" value="480" />
      <LABEL index="14" value="520" />
      <LABEL index="15" value="560" />
      <LABEL index="16" value="600" />
      <LABEL index="17" value="640" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A9BE" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x218" flags="0x30">
    <title>Shift Pressure Phase - Full Ratio (torque band 0)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0393). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Full ratio for torque band state 0 (below the E0350 net-torque threshold); stock 2.750 / 1.500 / 0.875. Ratio points of the shift pressure phase (measured gear ratio): the phase ramps its pressure in between start and full and out by end. On the stock H3 the phase pressure curves are all zero, so these only matter if those are filled (E0393). Effect: shift pressure phase timing Evidence: ledger:E0393, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="120" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="200" />
      <LABEL index="7" value="240" />
      <LABEL index="8" value="280" />
      <LABEL index="9" value="320" />
      <LABEL index="10" value="360" />
      <LABEL index="11" value="400" />
      <LABEL index="12" value="440" />
      <LABEL index="13" value="480" />
      <LABEL index="14" value="520" />
      <LABEL index="15" value="560" />
      <LABEL index="16" value="600" />
      <LABEL index="17" value="640" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3AA2E" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x219" flags="0x30">
    <title>Shift Pressure Phase - End Ratio (torque band 0)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0393). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. End ratio for torque band state 0 (below the E0350 net-torque threshold); stock 2.000 / 1.250 / 0.750. Ratio points of the shift pressure phase (measured gear ratio): the phase ramps its pressure in between start and full and out by end. On the stock H3 the phase pressure curves are all zero, so these only matter if those are filled (E0393). Effect: shift pressure phase timing Evidence: ledger:E0393, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="120" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="200" />
      <LABEL index="7" value="240" />
      <LABEL index="8" value="280" />
      <LABEL index="9" value="320" />
      <LABEL index="10" value="360" />
      <LABEL index="11" value="400" />
      <LABEL index="12" value="440" />
      <LABEL index="13" value="480" />
      <LABEL index="14" value="520" />
      <LABEL index="15" value="560" />
      <LABEL index="16" value="600" />
      <LABEL index="17" value="640" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3AA9E" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x21A" flags="0x30">
    <title>Shift Pressure Phase - Start Ratio (torque band 1)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0393). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start ratio for torque band state 1 (above the E0350 net-torque threshold); stock 3.000 / 1.600 / 0.938. Ratio points of the shift pressure phase (measured gear ratio): the phase ramps its pressure in between start and full and out by end. On the stock H3 the phase pressure curves are all zero, so these only matter if those are filled (E0393). Effect: shift pressure phase timing Evidence: ledger:E0393, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="120" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="200" />
      <LABEL index="7" value="240" />
      <LABEL index="8" value="280" />
      <LABEL index="9" value="320" />
      <LABEL index="10" value="360" />
      <LABEL index="11" value="400" />
      <LABEL index="12" value="440" />
      <LABEL index="13" value="480" />
      <LABEL index="14" value="520" />
      <LABEL index="15" value="560" />
      <LABEL index="16" value="600" />
      <LABEL index="17" value="640" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A496" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x21B" flags="0x30">
    <title>Shift Pressure Phase - Full Ratio (torque band 1)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0393). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Full ratio for torque band state 1 (above the E0350 net-torque threshold); stock 2.750 / 1.500 / 0.875. Ratio points of the shift pressure phase (measured gear ratio): the phase ramps its pressure in between start and full and out by end. On the stock H3 the phase pressure curves are all zero, so these only matter if those are filled (E0393). Effect: shift pressure phase timing Evidence: ledger:E0393, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="120" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="200" />
      <LABEL index="7" value="240" />
      <LABEL index="8" value="280" />
      <LABEL index="9" value="320" />
      <LABEL index="10" value="360" />
      <LABEL index="11" value="400" />
      <LABEL index="12" value="440" />
      <LABEL index="13" value="480" />
      <LABEL index="14" value="520" />
      <LABEL index="15" value="560" />
      <LABEL index="16" value="600" />
      <LABEL index="17" value="640" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A506" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x21C" flags="0x30">
    <title>Shift Pressure Phase - End Ratio (torque band 1)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0393). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. End ratio for torque band state 1 (above the E0350 net-torque threshold); stock 2.000 / 1.250 / 0.750. Ratio points of the shift pressure phase (measured gear ratio): the phase ramps its pressure in between start and full and out by end. On the stock H3 the phase pressure curves are all zero, so these only matter if those are filled (E0393). Effect: shift pressure phase timing Evidence: ledger:E0393, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="120" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="200" />
      <LABEL index="7" value="240" />
      <LABEL index="8" value="280" />
      <LABEL index="9" value="320" />
      <LABEL index="10" value="360" />
      <LABEL index="11" value="400" />
      <LABEL index="12" value="440" />
      <LABEL index="13" value="480" />
      <LABEL index="14" value="520" />
      <LABEL index="15" value="560" />
      <LABEL index="16" value="600" />
      <LABEL index="17" value="640" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A576" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x21D" flags="0x0">
    <title>Tip-In Arming - Slip Threshold A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only) can only arm while the engine is turning less than a set amount faster than the transmission output implies in the current gear (torque converter plus gearbox slip). Below Threshold A it can arm; from Threshold A up to Threshold B it can arm only while engine torque is below the arm torque; at or above Threshold B it cannot arm. Once armed at closed throttle, opening the throttle starts the tip-in torque ramp. Stock both 250 rpm, so there is no in-between band. This is Threshold A. Effect: raise = tip-in management still arms with more converter slip Evidence: ledger:E0356, ledger:E0845, led...</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21524" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x21E" flags="0x0">
    <title>Tip-In Torque Limit - Floor Outside Lash Phase</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. Outside the lash phase the tip-in torque limit is raised to at least this value. The torque reduction requested is engine torque minus the limit, so at the stock 8191 Nm the stock H3 only reduces torque during the lash phase. Lower it to also limit torque during the default and fast phases. Effect: tip-in torque management Evidence: ledger:E...</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2151C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x21F" flags="0x0">
    <title>Tip-In Torque Limit - Start Floor, Alternate (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start floor of the tip-in limit used only when a transmission-type calibration flag is 0; it is 1 on the stock H3, which uses the start floor table instead. Stock 8191 Nm. Effect: tip-in torque management Evidence: ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21520" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x220" flags="0x0">
    <title>Tip-In Torque Ramp - Lash Step Hold Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up by a step each update. The step is the default step normally, the slow lash step while the driveline is taking up slack (gearbox slip above about 10 rpm, or engine speed rising faster than the slip-based limit), and the fast step once the limit has passed its target. Once the lash step is in use it stays in use while engine speed is still changing faster than this per update. Stock -20 rpm per update. Effect: raise = the lash step is dropped sooner Evidence: ledger:E0395, ledger:E0845</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21522" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm per update</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x221" flags="0x0">
    <title>Tip-In Torque Ramp - Fast Step Input Speed Trigger</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. After a shunt and swing back, the fast step starts once input speed rises faster than this per update. Stock 10 rpm per update. Effect: tip-in torque management Evidence: ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2152A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm per update</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x222" flags="0x30">
    <title>Trans Range Switch - Code to Range Map</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Maps the 4-input range switch code to the range the PCM uses (15 = invalid). Stock: codes 3 / 10 / 15 / 6 / 5 / 12 / 9 give ranges 0 / 1 / 2 / 3 / 5 / 6 / 7. A wrong entry makes the PCM misread the selector (E0396). Effect: which range the PCM believes is selected Evidence: ledger:E0396</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>16</indexcount>
      <units>switch code (4 inputs)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E7E0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>range code</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x223" flags="0x30">
    <title>Trans Range Switch - Debounce Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long a new range must read steadily before it is accepted, by new range (row) and previous decoded range (column). Stock 25 ms everywhere (E0396). Effect: range change acceptance delay Evidence: ledger:E0396</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>16</indexcount>
      <units>previous range</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>16</indexcount>
      <units>new range</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E846" mmedelementsizebits="8" mmedrowcount="16" mmedcolcount="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>1.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x224" flags="0x30">
    <title>LTFT Cell - Learn Enable (learn internal)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per fuel-trim cell: 1 = the cell may learn, 0 = it does not. Stock 1 except a few spare cells. A wrong edit silently stops trims learning in that cell. Effect: learn internal: edit with care Evidence: ledger:E0397</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35FDC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flag</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x225" flags="0x30">
    <title>Fuel Trim Monitor - Cell Ready Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per fuel trim cell: monitor passes counted in the cell before the monitor takes its value; until then the tracked value stays at 1.0. Stock 180 in every cell. The fuel trim monitor (P0171 system too lean, P0172 system too rich) tracks a per-bank value built from the long-term fuel trim code&#x27;s per-bank value, which is centred on 1.0. These per-cell settings shape it: a diagnostic, not a fueling value. Effect: raise = the monitor waits longer in a cell before using it Evidence: ledger:E0310, ledger:E0397, ledger:E0905</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3602C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>count</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x226" flags="0x30">
    <title>Fuel Trim Monitor - Cell Use</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per fuel trim cell, how the fuel trim monitor uses it: 0 = not used, 1 = purge set cell, 2 = non purge set cell (also the cells the purge-off test measures in), sampled only while commanded purge is at or below the non purge cell purge limit. Stock 1 for cells 0 to 19, 2 for cells 21 to 37, 0 for cells 20 and 38. The fuel trim monitor (P0171 system too lean, P0172 system too rich) samples the long term fuel trim cell the engine is in; cells 0 to 20 are the purge set and 21 to 38 the non purge set. Effect: 0 = the monitor ignores that cell; changing 1 and 2 moves a cell between the purge and non purge sets Evidence: ledger:E03...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>fuel trim cell</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3607C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>code</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x227" flags="0x30">
    <title>Fuel Trim Monitor - Cell Weight Set Index</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per fuel trim cell: which entry (21 to 38) of the weight arrays below the cell uses. The fuel trim monitor (P0171 system too lean, P0172 system too rich) tracks a per-bank value built from the long-term fuel trim code&#x27;s per-bank value, which is centred on 1.0. These per-cell settings shape it: a diagnostic, not a fueling value. Effect: changes which weights the cell uses Evidence: ledger:E0310, ledger:E0397, ledger:E0905</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x360CC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>index</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x228" flags="0x30">
    <title>Fuel Trim Monitor - Cell Weight, Above 1.0</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per weight set: when the input is above 1.0, the monitor uses 1.0 plus the excess times this weight. Stock 1.0 everywhere (the full excess). The fuel trim monitor (P0171 system too lean, P0172 system too rich) tracks a per-bank value built from the long-term fuel trim code&#x27;s per-bank value, which is centred on 1.0. These per-cell settings shape it: a diagnostic, not a fueling value. Effect: lower = the monitor sees less of a lean correction Evidence: ledger:E0310, ledger:E0397, ledger:E0905</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3611C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x229" flags="0x30">
    <title>Fuel Trim Monitor - Cell Weight, Above 1.0, Bank 2 (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Bank 2 copy of the weight above. The H3 has one bank, so this is never used. Stock 1.0. The fuel trim monitor (P0171 system too lean, P0172 system too rich) tracks a per-bank value built from the long-term fuel trim code&#x27;s per-bank value, which is centred on 1.0. These per-cell settings shape it: a diagnostic, not a fueling value. Effect: no effect on stock (inactive) Evidence: ledger:E0310, ledger:E0397, ledger:E0905</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3616C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x22A" flags="0x30">
    <title>Fuel Trim Monitor - Cell Weight, Below 1.0</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per weight set: when the input is below 1.0, the monitor uses 1.0 minus the shortfall times this weight. Stock 1.0 everywhere (the full shortfall). The fuel trim monitor (P0171 system too lean, P0172 system too rich) tracks a per-bank value built from the long-term fuel trim code&#x27;s per-bank value, which is centred on 1.0. These per-cell settings shape it: a diagnostic, not a fueling value. Effect: lower = the monitor sees less of a rich correction Evidence: ledger:E0310, ledger:E0397, ledger:E0905</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x361BC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x22B" flags="0x30">
    <title>Fuel Trim Monitor - Cell Weight, Below 1.0, Bank 2 (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Bank 2 copy of the weight below. The H3 has one bank, so this is never used. Stock 1.0. The fuel trim monitor (P0171 system too lean, P0172 system too rich) tracks a per-bank value built from the long-term fuel trim code&#x27;s per-bank value, which is centred on 1.0. These per-cell settings shape it: a diagnostic, not a fueling value. Effect: no effect on stock (inactive) Evidence: ledger:E0310, ledger:E0397, ledger:E0905</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3620C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x22C" flags="0x30">
    <title>Baro Estimate - Expected MAP Drop vs Throttle x RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How far MAP is expected to sit below baro; the PCM estimates baro as MAP + this x the baro factor and updates baro when the estimate is steady above the throttle threshold. Stock 0.5 to 7.7 kPa at wide throttle, up to 59 kPa at small throttle and high rpm. Effect: raise = higher baro estimate from the same MAP Evidence: ledger:E0398, ledger:E0716</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>% throttle area</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="12.5" />
      <LABEL index="2" value="25" />
      <LABEL index="3" value="37.5" />
      <LABEL index="4" value="50" />
      <LABEL index="5" value="62.5" />
      <LABEL index="6" value="75" />
      <LABEL index="7" value="87.5" />
      <LABEL index="8" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21690" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x22D" flags="0x30">
    <title>Baro Estimate - Drop Factor vs Baro</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the expected MAP drop by baro: stock 0.65 at 65 kPa to 1.0 at 105 kPa (E0398). Effect: raise = larger drop allowance Evidence: ledger:E0398</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="65" />
      <LABEL index="1" value="70" />
      <LABEL index="2" value="75" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="85" />
      <LABEL index="5" value="90" />
      <LABEL index="6" value="95" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x217C4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x22E" flags="0x30">
    <title>Baro Estimate - Minimum Throttle for Update vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle area, by rpm, above which a steady MAP-based estimate may update the PCM&#x27;s barometric pressure. Stock 2 % at low rpm rising to 6.5 % from 5632 rpm. Effect: raise = baro updates only at wider throttle Evidence: ledger:E0398, ledger:E0689, ledger:E0716, ledger:E0733</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x217D8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle area</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.000000</max>
      <MATH equation="X/327.675"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x22F" flags="0x30">
    <title>Cam Phasing (region) - Base Target by Region</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Region-based exhaust cam target for each driving region (rpm band x throttle band, plus two closed-throttle regions), in desired-cam degrees. Stock 12 / 16 / 22 deg in the open regions, 7 and 10 deg at closed throttle. Multiplied by the baro, gear, coolant and intake temperature factors. The code path is traced; a drive log has not yet confirmed it in normal driving. Effect: changes exhaust cam phasing Evidence: ledger:E0399, ledger:E0744</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>cam phasing region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="below 1350 rpm, 0.5-1.8 %" />
      <LABEL index="1" value="1350-1750 rpm, 0.5-1.3 %" />
      <LABEL index="2" value="1750-2150 rpm, 0.5-1.2 %" />
      <LABEL index="3" value="above 2150 rpm, 0.5-1.3 %" />
      <LABEL index="4" value="below 1350 rpm, 1.8-2.6 %" />
      <LABEL index="5" value="1350-1750 rpm, 1.3-3.5 %" />
      <LABEL index="6" value="1750-2150 rpm, 1.2-4 %" />
      <LABEL index="7" value="above 2150 rpm, 1.3-5 %" />
      <LABEL index="8" value="below 1350 rpm, 2.6-5 %" />
      <LABEL index="9" value="1350-1750 rpm, 3.5-5 %" />
      <LABEL index="10" value="1750-2150 rpm, 4-6.2 %" />
      <LABEL index="11" value="above 2150 rpm, 5-8.1 %" />
      <LABEL index="12" value="below 1350 rpm, 5-up %" />
      <LABEL index="13" value="1350-1750 rpm, 5-up %" />
      <LABEL index="14" value="1750-2150 rpm, 6.2-up %" />
      <LABEL index="15" value="above 2150 rpm, 8.1-up %" />
      <LABEL index="16" value="closed, below 2800 rpm" />
      <LABEL index="17" value="closed, above 2800 rpm" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22EE4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x230" flags="0x30">
    <title>Cam Phasing (region) - Baro Factor by Region</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the region-based exhaust cam target by barometric band (rows: below 80 kPa, above 90 kPa, between) and driving region. Stock 0.45 to 1.0 below 80 kPa, 1.0 otherwise. The code path is traced; a drive log has not yet confirmed it in normal driving. Effect: changes cam phasing at altitude Evidence: ledger:E0399, ledger:E0744</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>cam phasing region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="below 1350 rpm, 0.5-1.8 %" />
      <LABEL index="1" value="1350-1750 rpm, 0.5-1.3 %" />
      <LABEL index="2" value="1750-2150 rpm, 0.5-1.2 %" />
      <LABEL index="3" value="above 2150 rpm, 0.5-1.3 %" />
      <LABEL index="4" value="below 1350 rpm, 1.8-2.6 %" />
      <LABEL index="5" value="1350-1750 rpm, 1.3-3.5 %" />
      <LABEL index="6" value="1750-2150 rpm, 1.2-4 %" />
      <LABEL index="7" value="above 2150 rpm, 1.3-5 %" />
      <LABEL index="8" value="below 1350 rpm, 2.6-5 %" />
      <LABEL index="9" value="1350-1750 rpm, 3.5-5 %" />
      <LABEL index="10" value="1750-2150 rpm, 4-6.2 %" />
      <LABEL index="11" value="above 2150 rpm, 5-8.1 %" />
      <LABEL index="12" value="below 1350 rpm, 5-up %" />
      <LABEL index="13" value="1350-1750 rpm, 5-up %" />
      <LABEL index="14" value="1750-2150 rpm, 6.2-up %" />
      <LABEL index="15" value="above 2150 rpm, 8.1-up %" />
      <LABEL index="16" value="closed, below 2800 rpm" />
      <LABEL index="17" value="closed, above 2800 rpm" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>baro band</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="&lt; 80 kPa" />
      <LABEL index="1" value="&gt; 90 kPa" />
      <LABEL index="2" value="80-90 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22F0C" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x231" flags="0x30">
    <title>Cam Phasing (region) - Gear Factor by Region</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the region-based exhaust cam target by transmission state (rows 0 to 4) and driving region. Stock 0.05 to 1.0 in 1st gear, 1.0 in the other gears. The code path is traced; a drive log has not yet confirmed it in normal driving. Effect: changes cam phasing by gear Evidence: ledger:E0399, ledger:E0744</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>cam phasing region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="below 1350 rpm, 0.5-1.8 %" />
      <LABEL index="1" value="1350-1750 rpm, 0.5-1.3 %" />
      <LABEL index="2" value="1750-2150 rpm, 0.5-1.2 %" />
      <LABEL index="3" value="above 2150 rpm, 0.5-1.3 %" />
      <LABEL index="4" value="below 1350 rpm, 1.8-2.6 %" />
      <LABEL index="5" value="1350-1750 rpm, 1.3-3.5 %" />
      <LABEL index="6" value="1750-2150 rpm, 1.2-4 %" />
      <LABEL index="7" value="above 2150 rpm, 1.3-5 %" />
      <LABEL index="8" value="below 1350 rpm, 2.6-5 %" />
      <LABEL index="9" value="1350-1750 rpm, 3.5-5 %" />
      <LABEL index="10" value="1750-2150 rpm, 4-6.2 %" />
      <LABEL index="11" value="above 2150 rpm, 5-8.1 %" />
      <LABEL index="12" value="below 1350 rpm, 5-up %" />
      <LABEL index="13" value="1350-1750 rpm, 5-up %" />
      <LABEL index="14" value="1750-2150 rpm, 6.2-up %" />
      <LABEL index="15" value="above 2150 rpm, 8.1-up %" />
      <LABEL index="16" value="closed, below 2800 rpm" />
      <LABEL index="17" value="closed, above 2800 rpm" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22F42" mmedelementsizebits="8" mmedrowcount="5" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x232" flags="0x30">
    <title>Cam Phasing - IAT Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Region-based cam phasing (probably active in normal driving; awaiting a drive log): factor on the cam target by intake air temperature. Stock 1.0 up to 88 C, 0.75 above 104 C. Effect: changes cam phasing when hot Evidence: ledger:E0399</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22FD6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x233" flags="0x0">
    <title>Cam Phasing (region) - Region Change Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Region-based exhaust cam phasing: how long a new driving region must hold before the cam target follows it. Stock 0.15 s. The code path is traced; a drive log has not yet confirmed it in normal driving. Effect: changes when cam phasing acts Evidence: ledger:E0399</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22EE2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x234" flags="0x0">
    <title>Cam Phasing (region) - Baro Low Band Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Region-based exhaust cam phasing uses its high-altitude factor row below this barometric pressure. Stock 80 kPa. The code path is traced; a drive log has not yet confirmed it in normal driving. Effect: changes when cam phasing acts Evidence: ledger:E0399</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22F08" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x235" flags="0x0">
    <title>Cam Phasing (region) - Baro High Band Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Region-based exhaust cam phasing uses its sea-level factor row above this barometric pressure; between the two bands it uses the middle row. Stock 90 kPa. The code path is traced; a drive log has not yet confirmed it in normal driving. Effect: changes when cam phasing acts Evidence: ledger:E0399</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22F0A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x236" flags="0x0">
    <title>Cam Phasing - Enable Off Below MAP (pair A)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Region-based exhaust cam phasing is disabled again once MAP falls below this value (pair A; the pair is chosen by barometric pressure). Stock 10 kPa. The code path is traced; a drive log has not yet confirmed it in normal driving. Effect: changes when cam phasing acts Evidence: ledger:E0399</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22D72" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x237" flags="0x0">
    <title>Cam Phasing - Enable On Above MAP (pair A)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Region-based exhaust cam phasing is enabled once MAP rises above this value (pair A; the pair is chosen by barometric pressure). Stock 34 kPa. The code path is traced; a drive log has not yet confirmed it in normal driving. Effect: changes when cam phasing acts Evidence: ledger:E0399</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22D74" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x238" flags="0x0">
    <title>Cam Phasing - Enable Off Below MAP (pair B)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Region-based exhaust cam phasing is disabled again once MAP falls below this value (pair B; the pair is chosen by barometric pressure). Stock 10 kPa. The code path is traced; a drive log has not yet confirmed it in normal driving. Effect: changes when cam phasing acts Evidence: ledger:E0399</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22D76" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x239" flags="0x0">
    <title>Cam Phasing - Enable On Above MAP (pair B)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Region-based exhaust cam phasing is enabled once MAP rises above this value (pair B; the pair is chosen by barometric pressure). Stock 34 kPa. The code path is traced; a drive log has not yet confirmed it in normal driving. Effect: changes when cam phasing acts Evidence: ledger:E0399</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22D78" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x23A" flags="0x0">
    <title>Cam Phasing (region) - Closed Throttle Ends Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once in the closed-throttle regions, region-based exhaust cam phasing leaves them when throttle reaches this value. Stock 0.30 %. The code path is traced; a drive log has not yet confirmed it in normal driving. Effect: changes when cam phasing acts Evidence: ledger:E0399</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x23090" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x23B" flags="0x0">
    <title>Cam Phasing (region) - Closed Throttle Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Region-based exhaust cam phasing treats the throttle as closed (the closed-throttle regions) once throttle falls below this value. Stock 0.50 %. The code path is traced; a drive log has not yet confirmed it in normal driving. Effect: changes when cam phasing acts Evidence: ledger:E0399</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x23092" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x23C" flags="0x0">
    <title>Cam Phasing (region) - Closed-Throttle RPM Split</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Region-based exhaust cam phasing splits closed throttle into a low-rpm and a high-rpm region at this engine speed. Stock 2800 rpm. The code path is traced; a drive log has not yet confirmed it in normal driving. Effect: changes when cam phasing acts Evidence: ledger:E0399</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x23094" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x23D" flags="0x30">
    <title>Shift Torque Term vs Turbine Speed</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 points]; COUNT is a structure word, never edit it (E0400). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque term by turbine speed (0 to 8192 rpm), one row per upshift. During an upshift half of it is added to the shift torque that picks the shift pressure, and the transmission input torque divided by it picks the row of the shift pressure multipliers; a downshift reads it on the turbine speed the gear gives and takes half off instead. Stock rising from 0 to 484 Nm (1-2), 350 Nm (2-3) and 400 Nm (3-4). Effect: raise = higher shift torque during an upshift at that turbine speed, so firmer shift pressure Evidence: ledger:E0235, ledger:E04...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E352" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x23E" flags="0x30">
    <title>Pedal Gain Reduction - Acceleration Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle acceleration above which the pedal gain reduction can start, by driveline output torque (engine torque through converter, gear and final drive, 0 to 648 Nm) and vehicle speed (0 to 256 km/h). When the truck accelerates at or above this for the confirm time, the PCM lowers the pedal throttle request factor. Stock 120 km/h/s everywhere, which is never reached, so the reduction does not run on the stock file. Effect: lower = the pedal gain reduction starts at gentler acceleration Evidence: ledger:E0403, ledger:E0937, ledger:E1203</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>km/h (vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="32" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="96" />
      <LABEL index="4" value="128" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="192" />
      <LABEL index="7" value="224" />
      <LABEL index="8" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>Nm (driveline output torque)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="81" />
      <LABEL index="2" value="162" />
      <LABEL index="3" value="243" />
      <LABEL index="4" value="324" />
      <LABEL index="5" value="405" />
      <LABEL index="6" value="486" />
      <LABEL index="7" value="567" />
      <LABEL index="8" value="648" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23E0A" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h/s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>127.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x23F" flags="0x0">
    <title>Cam Target Spark-Limit Reduction - Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam target reduction while spark is limited: the load-based cam target is multiplied by a factor (1.0 = no change). While spark has been held below its reference spark for half a second, the factor drops by the step down every down period, never below the floor; otherwise it climbs back by the step up every up period. Stock floor is 1.0, so on the stock calibration the factor stays at 1.0. Stock 1.0 (inert). Effect: lower = lets the cam target be reduced while spark is limited Evidence: ledger:E0720, ledger:E0875</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2306C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x240" flags="0x0">
    <title>Load-Based Cam Phasing - Pedal Demand Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Load-based cam phasing: above this pedal demand (percent of throttle area the driver is asking for) the cam is phased by the load-based cam target instead of the base schedule. Once active, it stays active until pedal demand drops this far below the threshold. Stock 3.0 %. Effect: raise = holds load-based cam phasing on longer as the pedal comes back Evidence: ledger:E0358, ledger:E0769, ledger:E0872</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x230C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% (pedal area demand)</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x241" flags="0x0">
    <title>Cam and Volumetric Efficiency Deficit Blend Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fast lag weight of the cam phase transient detector: share of the new cam phase excess (cam phase above the Cam Phase Ceiling) taken into the fast filtered excess each update, for every predictor region. Stock 0.5. Effect: higher = fast value follows the excess faster, so a larger gap to the slow value and more transients flagged Evidence: ledger:E0772, ledger:E0805, ledger:E1277, ledger:E1572, ledger:E1574</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C5F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain (Q16, unitless)</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x242" flags="0x0">
    <title>Oil Life Reset - Release Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil life reset with the accelerator (key on, engine not turning): after a press the signal must fall below this before the next press can count. Stock 20 %. Effect: raise = the accelerator needs to be released less far between presses Evidence: ledger:E1128</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C9EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x243" flags="0x0">
    <title>Oil Life Reset - Presses Needed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil life reset with the accelerator (key on, engine not turning): number of presses inside the time window that resets the oil life. Stock 3. Effect: raise = more presses are needed Evidence: ledger:E1128</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C9EE" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>presses</units>
    <decimalpl>0</decimalpl>
    <min>1.000000</min>
    <max>256.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X+1"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x244" flags="0x0">
    <title>Oil Life Reset - Time Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil life reset with the accelerator (key on, engine not turning): time from the first press in which all presses must be made; after it the count starts again. Stock 5 s. Effect: raise = more time to complete the presses Evidence: ledger:E1128</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C9F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x245" flags="0x0">
    <title>Idle Speed Control - Reference Freeze Reference Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: the reference freeze (see Reference Freeze RPM Error) applies only while the idle speed reference is at or below this. Stock 900 rpm. Effect: lower = the freeze applies only at lower reference speeds Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2273E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x246" flags="0x0">
    <title>Idle Speed Control - Reference Fall Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: rate at which the idle speed reference moves down toward its target while holding idle. Stock 40 rpm per second. Effect: raise = the idle speed reference comes down faster Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22740" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm per s</units>
    <decimalpl>0</decimalpl>
    <min>-163840.000000</min>
    <max>163835.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*5"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x247" flags="0x0">
    <title>Idle Speed Control - Reference Rise Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: rate at which the idle speed reference moves up toward its target while holding idle. Stock 400 rpm per second. Effect: raise = the idle speed reference comes up faster Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22742" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm per s</units>
    <decimalpl>0</decimalpl>
    <min>-163840.000000</min>
    <max>163835.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*5"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x248" flags="0x30">
    <title>Shift Lamp - Pedal Maximum by Gear vs RPM</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift lamp request (a data bus signal for a manual transmission upshift lamp): highest pedal position (driver throttle request) at which the lamp may show, for each gear by engine speed: the lamp asks for an upshift only at part throttle. Stock 20 % at low speed rising to 100 % near 6000 rpm; 1 % in the sixth row, which keeps the lamp off in top gear. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E1143</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="5th" />
      <LABEL index="5" value="6th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CAC4" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x249" flags="0x30">
    <title>Cam Phaser Base Duty vs Coolant and Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base duty for the exhaust cam phaser solenoid by coolant temperature (rows) and system voltage 9.6 to 15.2 V (columns). The controller&#x27;s integrator and proportional terms are added to it. Falls with voltage in every row. Stock 33 to 94 %. Effect: raise = more cam phaser solenoid duty before the controller corrects Evidence: ledger:E0427, ledger:E0689, ledger:E1226</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>V</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="9.6" />
      <LABEL index="1" value="10.3" />
      <LABEL index="2" value="11" />
      <LABEL index="3" value="11.7" />
      <LABEL index="4" value="12.4" />
      <LABEL index="5" value="13.1" />
      <LABEL index="6" value="13.8" />
      <LABEL index="7" value="14.5" />
      <LABEL index="8" value="15.2" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22BDE" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x24A" flags="0x30">
    <title>Misfire - Catalyst Failed Windows Required</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: number of windows over the catalyst-damage limit, among the recent ones, needed for the first catalyst-damaging exceedance of a trip. Chosen by engine speed and load (nearest point; the smaller of the values at the start and end of the window). Stock 2 at low speed and load, 1 elsewhere. Keep below 256. Effect: raise = more failed windows are needed before a catalyst-damaging misfire is declared Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>% load</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>8</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1000" />
      <LABEL index="2" value="2000" />
      <LABEL index="3" value="3000" />
      <LABEL index="4" value="4000" />
      <LABEL index="5" value="5000" />
      <LABEL index="6" value="6000" />
      <LABEL index="7" value="7000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37132" mmedelementsizebits="16" mmedrowcount="8" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>windows</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x24B" flags="0x30">
    <title>Tip-In Spark Advance - Amount vs Run Time and Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in spark advance (spark advance added for a short time when cylinder airmass jumps): degrees of advance added when the trigger fires, by engine run time (rows) and coolant (columns). It can only advance. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = more spark advance on a tip-in, once the trigger is reachable Evidence: ledger:E1142, ledger:E1288</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>s engine run time</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="20" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="60" />
      <LABEL index="4" value="80" />
      <LABEL index="5" value="100" />
      <LABEL index="6" value="120" />
      <LABEL index="7" value="140" />
      <LABEL index="8" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CC00" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x24C" flags="0x0">
    <title>Converter Heat - Min Trans Temp (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Counting only starts above this trans temp (stock 99.75 C). Part of the converter-heat hot-mode trigger: while the converter slips hard at speed with hot fluid, a heat count builds; past the limit the transmission goes into hot mode. The converter heat trigger is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (when hot mode is entered) Evidence: ledger:E0432, ledger:E1399</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DDD8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x24D" flags="0x0">
    <title>Converter Heat - Min Vehicle Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Counting only starts above this trans-side speed (stock 15 km/h). Part of the converter-heat hot-mode trigger: while the converter slips hard at speed with hot fluid, a heat count builds; past the limit the transmission goes into hot mode. The converter heat trigger is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (when hot mode is entered) Evidence: ledger:E0432, ledger:E1399</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DDD2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x24E" flags="0x0">
    <title>Converter Heat - Max Speed Ratio (slip) (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Counting runs while turbine / engine speed ratio is at or below this (stock 0.477). Part of the converter-heat hot-mode trigger: while the converter slips hard at speed with hot fluid, a heat count builds; past the limit the transmission goes into hot mode. The converter heat trigger is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (when hot mode is entered) Evidence: ledger:E0432, ledger:E1399</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DDD0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x24F" flags="0x0">
    <title>Converter Heat - Cancel Speed Ratio (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A pending count is cancelled once the ratio reaches this (stock 0.996, converter coupled). Part of the converter-heat hot-mode trigger: while the converter slips hard at speed with hot fluid, a heat count builds; past the limit the transmission goes into hot mode. The converter heat trigger is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (when hot mode is entered) Evidence: ledger:E0432, ledger:E1399</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DDD4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x250" flags="0x0">
    <title>Converter Heat - Cancel Window (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time after which a pending count with the ratio recovered is dropped (stock 15 s). Part of the converter-heat hot-mode trigger: while the converter slips hard at speed with hot fluid, a heat count builds; past the limit the transmission goes into hot mode. The converter heat trigger is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (when hot mode is entered) Evidence: ledger:E0432, ledger:E1399</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DD3C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x251" flags="0x30">
    <title>Converter Heat - Trigger Limit vs Trans Temp (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Heat count at which converter heat hot mode is entered, by transmission fluid temperature. Stock 418816 up to 104 C, falling to 0 from 128 C. Lower = hot mode sooner. While the converter slips hard at speed with hot fluid, a heat count builds; past this limit the transmission goes into hot mode. The converter heat trigger is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (lower = hot mode from converter heat sooner) Evidence: ledger:E0432, ledger:E1399</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3DD66" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>degC (trans temp)</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DD8A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>heat counts</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>524280.000000</max>
      <MATH equation="X*8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x252" flags="0x30">
    <title>Closed Loop Trim Step Interval - Base, O2 Lean</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): time between steps of the short term trim while the O2 reads lean. The interval is this base value, by airflow, times a factor that shortens it when the O2 signal is far past the switch point. The timer restarts after every step, so the trim keeps stepping at this interval for as long as the O2 stays on one side. Effect: raise = the trim adds fuel more slowly while the O2 reads lean Evidence: ledger:E0433, ledger:E0901, ledger:E1126</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25A16" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x253" flags="0x30">
    <title>Closed Loop Trim Step Interval - Base, O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): time between steps of the short term trim while the O2 reads rich. The interval is this base value, by airflow, times a factor that shortens it when the O2 signal is far past the switch point. The timer restarts after every step, so the trim keeps stepping at this interval for as long as the O2 stays on one side. Effect: raise = the trim removes fuel more slowly while the O2 reads rich Evidence: ledger:E0433, ledger:E0901, ledger:E1126</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25A2A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x254" flags="0x30">
    <title>Closed Loop Proportional Gain - Spare Mode</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): proportional part of the short term trim by airflow, first row while the O2 reads lean and second row while it reads rich, used in place of the normal proportional gain curves in a spare mode. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1134</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>O2 state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="O2 lean" />
      <LABEL index="1" value="O2 rich" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25A66" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x255" flags="0x30">
    <title>Closed Loop Proportional Gain - Low Baro Mode</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): proportional part of the short term trim by airflow, first row while the O2 reads lean and second row while it reads rich, used in place of the normal proportional gain curves in the low baro mode. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1134</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>O2 state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="O2 lean" />
      <LABEL index="1" value="O2 rich" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25A8E" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x256" flags="0x30">
    <title>Closed Loop Proportional Gain - Coolant Window Mode</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): proportional part of the short term trim by airflow, first row while the O2 reads lean and second row while it reads rich, used in place of the normal proportional gain curves in the coolant window mode. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1134</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>O2 state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="O2 lean" />
      <LABEL index="1" value="O2 rich" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25AB6" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x257" flags="0x30">
    <title>Closed Loop Proportional Gain - O2 Lean</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. This curve is the proportional size by airflow while the O2 reads lean (at factor 1.0). Stock 1.3 % at idle, 6.3 % at 4.8 g/s, 7.0 % from 8 to 29.5 g/s, 5.7 % at 40 g/s. Effect: raise = stronger proportional correction (faster, but more trim ripp...</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25ADE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x258" flags="0x30">
    <title>Closed Loop Proportional Gain - O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. This curve is the proportional size by airflow while the O2 reads rich (at factor 1.0). Stock equal to the lean curve. Effect: raise = stronger proportional correction (faster, but more trim ripple) Evidence: ledger:E0433, ledger:E0903, ledger:E1126</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25AF2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x259" flags="0x30">
    <title>Closed Loop Proportional Term Ceiling vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit of the closed loop proportional correction by airflow, before it is multiplied by the Proportional Term Ceiling Factor for the current gear, converter clutch and coolant state. Same scale as the proportional gain curves. Stock 200 %, which with the stock factors of 2.0 never limits. Effect: lower = caps the closed loop proportional correction at that airflow Evidence: ledger:E0433, ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s used airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4.8" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="13.2" />
      <LABEL index="4" value="21.8" />
      <LABEL index="5" value="29.5" />
      <LABEL index="6" value="40.3" />
      <LABEL index="7" value="51.8" />
      <LABEL index="8" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25B08" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x25A" flags="0x30">
    <title>Closed Loop O2 Switch Delay - Factor, O2 Lean</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. This curve scales the switch delay (batch 56) by how far the O2 is past its switch point, while it reads lean. Stock 1.0 up to 160 mV, 0.5 from 352 mV. Effect: raise = longer delay at that distance Evidence: ledger:E0433, ledger:E0903</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25B1C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x25B" flags="0x30">
    <title>Closed Loop O2 Switch Delay - Factor, O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. This curve scales the switch delay while the O2 reads rich. Stock equal to the lean curve. Effect: raise = longer delay at that distance Evidence: ledger:E0433, ledger:E0903</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25B40" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x25C" flags="0x30">
    <title>Closed Loop Proportional Factor - O2 Lean</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. This curve scales the proportional term off idle by how far the O2 is past its switch point, while it reads lean. Stock 0.4 up to 192 mV rising to 0.8 from 352 mV. Effect: raise = stronger proportional correction at that distance Evidence: ledger...</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25B64" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-2.000000</min>
      <max>1.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x25D" flags="0x30">
    <title>Closed Loop Proportional Factor - O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. This curve scales the proportional term off idle while the O2 reads rich. Stock equal to the lean curve. Effect: raise = stronger proportional correction at that distance Evidence: ledger:E0433, ledger:E0903, ledger:E1126</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25B88" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-2.000000</min>
      <max>1.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x25E" flags="0x30">
    <title>Closed Loop Proportional Factor - Idle</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. This curve scales the proportional term in closed-throttle idle (both O2 states). Stock 1.0 up to 192 mV rising to 1.6 from 384 mV. Effect: raise = stronger proportional correction at idle Evidence: ledger:E0433, ledger:E0903, ledger:E0936</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25BAC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-2.000000</min>
      <max>1.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x25F" flags="0x30">
    <title>Closed Loop Slow-Sensor Trim Step Interval - Base, O2 Lean (inactive)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: the map that would select the slow sensor tables on the lean side is all zero. Closed loop fuel, slow sensor tables: time between steps of the short term trim while the O2 reads lean. The interval is this base value, by airflow, times a factor that shortens it when the O2 signal is far past the switch point. The timer restarts after every step, so the trim keeps stepping at this interval for as long as the O2 stays on one side. Effect: no effect on the stock calibration Evidence: ledger:E0433, le...</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25CE0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x260" flags="0x30">
    <title>Closed Loop Slow-Sensor Trim Step Interval - Base, O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel, slow sensor tables (used while the O2 reads rich when the Alternate Tables Map selects them for the measured O2 response times): time between steps of the short term trim. The interval is this base value, by airflow, times a factor that shortens it when the O2 signal is far past the switch point. The timer restarts after every step, so the trim keeps stepping at this interval for as long as the O2 stays on one side. Effect: raise = the trim removes fuel more slowly with a slow sensor Evidence: ledger:E0433, ledge...</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25CF4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x261" flags="0x30">
    <title>Closed Loop Slow-Sensor Switch Delay - Factor, O2 Lean (inactive)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this is the lean-side row of an alternate closed-loop table, and the map that would select the lean side is all zero. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). Effect: no effect on the stock calibration Evidence: ledger:E0433, ledger:E0904</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25D0C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x262" flags="0x30">
    <title>Closed Loop Slow-Sensor Switch Delay - Factor, O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). This curve scales the switch delay by how far the O2 is past its switch point. Stock 1.0 up to 160 mV, 0.5 from 352 mV. Effect: raise = longer delay at that distance Evidence: ledger:E0433, ledger:E0904</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25D30" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x263" flags="0x30">
    <title>Closed Loop Slow-Sensor Proportional Factor, O2 Lean (inactive)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this is the lean-side row of an alternate closed-loop table, and the map that would select the lean side is all zero. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). Effect: no effect on the stock calibration Evidence: ledger:E0433, ledger:E0904, ledger:E0936</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25D5C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-2.000000</min>
      <max>1.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x264" flags="0x30">
    <title>Closed Loop Slow-Sensor Proportional Factor, O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). This curve scales the proportional term off idle by how far the O2 is past its switch point. Stock 0.4 rising to 0.8 from 352 mV. Effect: raise = stronger proportional correction at that distance Evidence: ledger:E0433, ledger:E0904, ledger:E1126</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25D80" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-2.000000</min>
      <max>1.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x265" flags="0x30">
    <title>Closed Loop Slow-Sensor Proportional Gain, O2 Lean (inactive)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this is the lean-side row of an alternate closed-loop table, and the map that would select the lean side is all zero. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). Effect: no effect on the stock calibration Evidence: ledger:E0433, ledger:E0904, ledger:E0936</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25DA4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x266" flags="0x30">
    <title>Closed Loop Slow-Sensor Proportional Gain, O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). This curve is the proportional size by airflow (at factor 1.0). Stock as the normal gain but 8.7 % from 29.5 g/s. Effect: raise = stronger proportional correction Evidence: ledger:E0433, ledger:E0904, ledger:E1126</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25DB8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x267" flags="0x30">
    <title>Closed Loop Slow-Sensor Proportional Factor - Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). This curve scales the proportional term in closed-throttle idle. Stock 1.0 rising to 1.6 from 384 mV. Effect: raise = stronger proportional correction at idle Evidence: ledger:E0433, ledger:E0904, ledger:E0936</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>mV past the O2 switch point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="32" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="96" />
      <LABEL index="4" value="128" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="192" />
      <LABEL index="7" value="224" />
      <LABEL index="8" value="256" />
      <LABEL index="9" value="288" />
      <LABEL index="10" value="320" />
      <LABEL index="11" value="352" />
      <LABEL index="12" value="384" />
      <LABEL index="13" value="416" />
      <LABEL index="14" value="448" />
      <LABEL index="15" value="480" />
      <LABEL index="16" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25DCE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-2.000000</min>
      <max>1.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x268" flags="0x30">
    <title>Closed Loop Slow-Sensor Trim Jump</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). These are the trim jumps: idle lean (unused), idle rich, off idle lean (unused), off idle rich. Stock 0.40 % each. Effect: raise = bigger trim step at each O2 switch Evidence: ledger:E0433, ledger:E0904</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>idle / off idle, O2 state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="idle lean (unused)" />
      <LABEL index="1" value="idle rich" />
      <LABEL index="2" value="off idle lean (unused)" />
      <LABEL index="3" value="off idle rich" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25D54" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x269" flags="0x0">
    <title>A/C Refrigerant Pressure Sensor Check Enable (P0532 / P0533)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the A/C refrigerant pressure sensor circuit low / high checks on or off. 1: the PCM runs the check and can set P0532 / P0533. 0: the check never runs, so P0532 / P0533 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0532 / P0533 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2015A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x26A" flags="0x0">
    <title>P0532 Fail - Consecutive Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C refrigerant pressure sensor circuit low check P0532: the code sets after this many samples in a row read at or below the low limit. Stock 3. Effect: raise = more low samples in a row are needed to set P0532 Evidence: ledger:E1034</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2015C" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x26B" flags="0x0">
    <title>P0533 Fail - Consecutive Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C refrigerant pressure sensor circuit high check P0533: the code sets after this many samples in a row read at or above the high limit. Stock 3. Effect: raise = more high samples in a row are needed to set P0533 Evidence: ledger:E1034</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2015D" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x26C" flags="0x0">
    <title>P0532 Check - Sensor Voltage Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C refrigerant pressure sensor circuit low check P0532: a sample counts as low when the sensor voltage is at or below this. Stock 0.10 V. Effect: raise = higher voltages already count as a low circuit Evidence: ledger:E1048</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2015E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>9.999847</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/6553.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x26D" flags="0x0">
    <title>P0533 Check - Sensor Voltage High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C refrigerant pressure sensor circuit high check P0533: a sample counts as high when the sensor voltage is at or above this. Stock 4.90 V. Effect: lower = lower voltages already count as a high circuit Evidence: ledger:E1048</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20160" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>9.999847</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/6553.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x26E" flags="0x0">
    <title>P0622 Test - Run Condition, Engine Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0622 (generator field signal), engine running check: runs only below this engine speed. Stock 3000 rpm. Effect: raise = the running check also runs at higher engine speed Evidence: ledger:E1076</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20828" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x26F" flags="0x0">
    <title>P0622 Fail - Field Duty, Engine Stopped</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0622, ignition on with the engine stopped: generator field signal duty at or above this for the engine-stopped fail time sets the code. Stock 65 %. Effect: raise = a higher field signal is tolerated with the engine stopped Evidence: ledger:E1076</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2082A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x270" flags="0x0">
    <title>P0622 Fail - Field Duty, Engine Running</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0622, engine running: generator field signal duty at or below this for the engine-running fail time sets the code. Stock 5 %. Effect: lower = a lower field signal is tolerated with the engine running Evidence: ledger:E1076</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2082C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x271" flags="0x0">
    <title>U1301 Fail Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Class 2 data link high check U1301: the code sets once the fault has been present for this long. Stock 3 s. Effect: raise = the fault must last longer before U1301 sets Evidence: ledger:E1035</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x208F4" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x272" flags="0x0">
    <title>U1300 Fail Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Class 2 data link low check U1300: the code sets once the fault has been present for this long. Stock 3 s. Effect: raise = the fault must last longer before U1300 sets Evidence: ledger:E1035</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x208F5" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x273" flags="0x0">
    <title>System Voltage High Threshold (P0563)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0563 (system voltage high) counts toward a fail while system voltage is at or above this, and the PCM treats voltage above it as outside the normal range. Stock 16.0 V. Effect: raise = higher voltage is tolerated before P0563 Evidence: ledger:E0978</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2092A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x274" flags="0x0">
    <title>System Voltage High Check Enable (P0563)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the system voltage high check on or off. 1: the PCM runs the check and can set P0563. 0: the check never runs, so P0563 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0563 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20930" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x275" flags="0x0">
    <title>System Voltage Low Threshold (P0562)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0562 (system voltage low) counts toward a fail while system voltage is at or below this, and the PCM treats voltage below it as outside the normal range. Stock 10.0 V. Effect: lower = lower voltage is tolerated before P0562 Evidence: ledger:E0978</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20932" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x276" flags="0x0">
    <title>System Voltage Low Check Enable (P0562)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the system voltage low check on or off. 1: the PCM runs the check and can set P0562. 0: the check never runs, so P0562 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0562 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2093A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x277" flags="0x0">
    <title>P250A Check - Vehicle Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P250A check (switched off in the stock calibration): fail periods are only timed at or above this vehicle speed. Stock 0 km/h. Effect: raise = the check only runs at higher speeds Evidence: ledger:E1037</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2314E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x278" flags="0x0">
    <title>P250A Check - Throttle Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P250A check (switched off in the stock calibration): fail periods are only timed at or above this throttle position. Stock 0 %. Effect: raise = the check only runs at larger throttle openings Evidence: ledger:E1037</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23150" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x279" flags="0x0">
    <title>P250A Check - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P250A check (switched off in the stock calibration): fail periods are only timed at or above this engine speed. Stock 550 rpm. Effect: raise = the check only runs at higher engine speeds Evidence: ledger:E1037</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23152" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x27A" flags="0x0">
    <title>P250A Fail - Period Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P250A check (switched off in the stock calibration): each time the monitored input has stayed in its fault state for this long with the run conditions met, one fail period is counted. Stock 10 s. Effect: raise = each fail period takes longer Evidence: ledger:E1037</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23154" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x27B" flags="0x0">
    <title>P250A Check - Start Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P250A check (switched off in the stock calibration): the monitored input must first have been in its fault state for this long in total since the last pass before fail periods are timed. Stock 10 s. Effect: raise = the check waits longer before timing fail periods Evidence: ledger:E1037</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23156" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x27C" flags="0x0">
    <title>P250A Fail - Period Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P250A check (switched off in the stock calibration): the code sets once this many fail periods have been counted. Stock 20. Effect: raise = more fail periods are needed to set P250A Evidence: ledger:E1037</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2315A" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x27D" flags="0x0">
    <title>P0068 Fail - Airflow Difference</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0068 airflow leg: measured airflow (MAF) differing from the airflow modelled from throttle position by more than this, in either direction. P0068 sets when this leg and the pressure leg both hold for the fail time. Stock 25 g/s. Effect: raise = a larger airflow disagreement is tolerated Evidence: ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B1E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>-512.000000</min>
    <max>511.984375</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/64"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x27E" flags="0x0">
    <title>Knock Sensor Tests - Run Condition, Airmass Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock sensor checks (P0325, P0327, P0332): the checks run only when cylinder airmass is above this. The sensor signal evaluation that feeds them starts at a quarter of this airmass. Stock 0.26 g per cylinder. Effect: raise = the knock sensor checks run only at higher load Evidence: ledger:E1078</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32642" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/cyl</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>16.383750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x27F" flags="0x0">
    <title>P0315 Fail - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0315 (crankshaft variation not learned) sets once the variation values have been found not learned for this long. Stock 0.5 s. Effect: raise = P0315 takes longer to set Evidence: ledger:E1040</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328D2" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x280" flags="0x0">
    <title>P0116 Test - Drive Check Intake Air Rise Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116), when coolant at start-up is warmer than intake air by more than the pass limit but less than the fail limit: after the drive check time, the code sets unless intake air has risen at least this much above its lowest reading since start, in which case no decision is made. Stock 5 C. Effect: raise = a larger intake air rise is needed to avoid the fail Evidence: ledger:E1022</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x336F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x281" flags="0x0">
    <title>P0116 Test - Startup Intake Air Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116), when coolant at start-up is warmer than intake air by more than the pass limit but less than the fail limit: no decision is made if intake air temperature at start-up was at or below this. Stock 10 C. Effect: lower = the test also decides after colder starts Evidence: ledger:E1022</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x336F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x282" flags="0x0">
    <title>P0116 Test - Drive Check Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116), when coolant at start-up is warmer than intake air by more than the pass limit but less than the fail limit: the decision is made after more than this much driving above the drive check speed. Stock 400 s. Effect: raise = more driving is needed before the decision Evidence: ledger:E1022</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x336F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x283" flags="0x0">
    <title>P0116 Test - Drive Check Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116), when coolant at start-up is warmer than intake air by more than the pass limit but less than the fail limit: only time spent above this vehicle speed counts toward the drive check time. Stock 40 km/h. Effect: raise = only faster driving counts Evidence: ledger:E1022</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x336F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x284" flags="0x0">
    <title>P0116 Test - Long Crank Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116), when coolant at start-up is warmer than intake air by more than the pass limit but less than the fail limit: if the engine cranked for at least this long, the code sets at once when fuel level is above the long crank fuel level, and otherwise no decision is made. Stock 10 s. Effect: raise = only longer cranking takes this path Evidence: ledger:E1022</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x336F8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x285" flags="0x0">
    <title>P0116 Test - Long Crank Fuel Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116), when coolant at start-up is warmer than intake air by more than the pass limit but less than the fail limit: after a long crank the code sets only if fuel level is above this. Stock 10 %. Effect: raise = more fuel is needed for the long crank fail Evidence: ledger:E1022</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3371E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x286" flags="0x0">
    <title>P0117 / P1114 Check - Hot Soak Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit low check: for this long after a start, low-circuit samples are ignored while minimum intake air temperature is above the hot soak limit. Stock 10 s. Effect: raise = hot soak readings are ignored for longer after a start Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x287" flags="0x0">
    <title>P0117 / P1114 Check - Hot Soak Intake Air Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit low check: minimum intake air temperature above which low-circuit samples are ignored right after a start. Stock 70 C. Effect: lower = samples are ignored after a cooler soak too Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x288" flags="0x0">
    <title>P0117 / P1114 Check - Sensor Resistance Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant temperature sensor circuit low check: a sample counts as low when the sensor resistance is below this (a shorted sensor or wire). Stock 25 ohm. Effect: raise = higher resistances already count as a low circuit Evidence: ledger:E1047</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337BC" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ohm</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>134217727.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x289" flags="0x0">
    <title>P0118 / P1115 Check - Sensor Resistance High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant temperature sensor circuit high check: a sample counts as high when the sensor resistance is above this (an open sensor or wire). Stock 1.8 Mohm. Effect: lower = lower resistances already count as a high circuit Evidence: ledger:E1047</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337C0" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ohm</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>134217727.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x28A" flags="0x0">
    <title>P0117 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit low check: P0117 sets once this many low-circuit samples are counted in a test window. Stock 50. Effect: raise = more low samples are needed to set P0117 Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x28B" flags="0x0">
    <title>P1114 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit low check: P1114 (intermittent) sets once this many low-circuit samples are counted in its longer test window. Stock 100. Effect: raise = more low samples are needed to set P1114 Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x28C" flags="0x0">
    <title>P0118 / P1115 Check - Cold Start Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit high check: for this long after a start, high-circuit samples are ignored while minimum intake air temperature is below the cold start limit. Stock 60 s. Effect: raise = cold start readings are ignored for longer after a start Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x28D" flags="0x0">
    <title>P0118 / P1115 Check - Cold Start Intake Air Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit high check: minimum intake air temperature below which high-circuit samples are ignored right after a start. Stock -7 C. Effect: raise = samples are ignored after a milder cold start too Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x28E" flags="0x0">
    <title>P0118 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit high check: P0118 sets once this many high-circuit samples are counted in a test window. Stock 50. Effect: raise = more high samples are needed to set P0118 Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x28F" flags="0x0">
    <title>P1115 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit high check: P1115 (intermittent) sets once this many high-circuit samples are counted in its longer test window. Stock 100. Effect: raise = more high samples are needed to set P1115 Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x290" flags="0x0">
    <title>Coolant Temp Sensor Circuit Checks Enable (P0117 / P0118 / P1114 / P1115)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the coolant temperature sensor circuit low / high and intermittent checks on or off. 1: the PCM runs the check and can set P0117 / P0118 / P1114 / P1115. 0: the check never runs, so P0117 / P0118 / P1114 / P1115 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0117 / P0118 / P1114 / P1115 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337D8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x291" flags="0x0">
    <title>P0464 Pass - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0464 (fuel level sensor intermittent, judged by the engine-off EVAP test): a pass is reported after this many samples unless the bad sample limit was exceeded first. Stock 3. Effect: raise = each decision window is longer Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D12" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x292" flags="0x0">
    <title>P0454 Pass - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0454 (tank pressure sensor intermittent, judged by the engine-off EVAP test): a pass is reported after this many samples unless the bad sample limit was exceeded first. Stock 3. Effect: raise = each decision window is longer Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D1E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x293" flags="0x0">
    <title>P0442 Fail - Threshold After a Failure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0442 (small leak, engine-off test): threshold used in place of the normal fail threshold once P0442 has failed, so the running average has to come down to this before the code can pass again. Stock 0.35. Effect: raise = it is easier to pass again after a failure Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D20" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x294" flags="0x0">
    <title>P0442 Fail - Leak Result Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0442 (small leak, engine-off test) sets when the running average of the leak result rises above this. The result of one test is 1 minus (vacuum reached minus pressure reached) divided by the reference: 0 for a tight tank, 1 when the tank pressure did not move at all. Stock 0.55. Effect: raise = a larger average leak result is needed to set P0442 Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D22" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x295" flags="0x0">
    <title>P0442 - Averaging Weight After a Failure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0442: share of each new leak result taken into the running average once P0442 has failed. Stock 0.175. Effect: raise = each test moves the average more Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D24" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x296" flags="0x0">
    <title>P0451 - Averaging Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): share of each new zero shift rating taken into the running average. Stock 0.20. Effect: raise = each zero check moves the average more Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D26" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x297" flags="0x0">
    <title>P0451 - Averaging Weight After a Failure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): the same share once P0451 has failed. Stock 0.20. Effect: raise = each zero check moves the average more Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D28" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x298" flags="0x0">
    <title>P0451 Fail - Zero Shift Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): the code sets when the running average of the zero shift rating rises above this (a rating of 1.0 is a shift equal to the zero shift limit). Stock 0.73. Effect: raise = a larger average zero shift is needed to set P0451 Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D40" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x299" flags="0x0">
    <title>P0451 Fail - Threshold After a Failure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): threshold used in place of the normal one once P0451 has failed. Stock 0.40. Effect: raise = it is easier to pass again after a failure Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D42" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x29A" flags="0x0">
    <title>P0464 Fail - Bad Sample Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0464 (fuel level sensor intermittent): the code sets when more than this many samples in a window were bad (the fuel level moved during the engine-off test and it was not put down to refuelling). Stock 1. Effect: raise = more bad samples are tolerated Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x29B" flags="0x0">
    <title>P0454 Fail - Bad Sample Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0454 (tank pressure sensor intermittent): the code sets when more than this many samples in a window were bad (the tank pressure signal jumped during the engine-off test). Stock 1. Effect: raise = more bad samples are tolerated Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x29C" flags="0x0">
    <title>P0442 - Averaging Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0442: share of each new leak result taken into the running average. Stock 0.175. Effect: raise = each test moves the average more Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x29D" flags="0x0">
    <title>P0522 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil pressure sensor circuit low check P0522 (switched off in the stock calibration): the code sets once this many samples in a test window read below the low limit. Stock 50. Effect: raise = more low samples are needed to set P0522 Evidence: ledger:E1042</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34722" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x29E" flags="0x0">
    <title>P0522 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil pressure sensor circuit low check P0522 (switched off in the stock calibration): a test window that reaches this many samples without failing passes. Stock 100. Effect: raise = each test window is longer Evidence: ledger:E1042</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34723" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x29F" flags="0x0">
    <title>P0523 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil pressure sensor circuit high check P0523 (switched off in the stock calibration): the code sets once this many samples in a test window read above the high limit. Stock 50. Effect: raise = more high samples are needed to set P0523 Evidence: ledger:E1042</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34728" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A0" flags="0x0">
    <title>P0523 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil pressure sensor circuit high check P0523 (switched off in the stock calibration): a test window that reaches this many samples without failing passes. Stock 100. Effect: raise = each test window is longer Evidence: ledger:E1042</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34729" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A1" flags="0x0">
    <title>P0336 Fail - Crank Resyncs per Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0336 (crank position sensor performance): the code sets when the crank signal has to be resynchronised this many times or more within one check window. Stock 20. Effect: raise = more crank resynchronisations are tolerated Evidence: ledger:E1080</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34CC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>resyncs</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A2" flags="0x0">
    <title>P0452 Check - Sensor Voltage Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel tank pressure sensor circuit low check P0452: a sample counts as low when the sensor voltage is below this. Stock 0.10 V. Effect: raise = higher voltages already count as a low circuit Evidence: ledger:E1016</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3581C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A3" flags="0x0">
    <title>P0453 Check - Sensor Voltage High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel tank pressure sensor circuit high check P0453: a sample counts as high when the sensor voltage is above this. Stock 4.90 V. Effect: lower = lower voltages already count as a high circuit Evidence: ledger:E1016</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3581E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A4" flags="0x0">
    <title>P2026 Fail - Sensor Resistance Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP fuel vapour temperature sensor circuit low check (P2026): a resistance below this counts as a fault sample. Stock 0 ohm. The check is switched off on this truck (code disabled), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0434, ledger:E1482</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F78" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ohm</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>134217727.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A5" flags="0x0">
    <title>P2027 Fail - Sensor Resistance Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP fuel vapour temperature sensor circuit high check (P2027): a resistance above this counts as a fault sample. Stock 1,000,000 ohm. The check is switched off on this truck (code disabled), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0434, ledger:E1482</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F7C" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ohm</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>134217727.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A6" flags="0x0">
    <title>P0463 Fuel Level Sensor High - Voltage Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0463 (fuel level sensor circuit high) counts time while the fuel level sender reads above this voltage. Stock 3.5 V. Effect: raise = a higher sender voltage is needed to count toward P0463 Evidence: ledger:E0957</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x364B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>9.999847</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/6553.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A7" flags="0x0">
    <title>P0462 Fuel Level Sensor Low - Voltage Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0462 (fuel level sensor circuit low) counts time while the fuel level sender reads below this voltage. Stock 0.53 V. Effect: lower = a lower sender voltage is needed to count toward P0462 Evidence: ledger:E0957</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x364B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>9.999847</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/6553.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A8" flags="0x0">
    <title>P0463 Fail - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0463 (fuel level sensor circuit high) sets once the sender has read above its high threshold for this long without returning to the normal range. Stock 60 s. Effect: raise = P0463 takes longer to set Evidence: ledger:E0957</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x364B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A9" flags="0x0">
    <title>P0461 Fail - Distance Without Level Change</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel level sensor stuck check P0461: the code sets once the vehicle has been driven about this far while the fuel level reading stayed inside the level change limit. Stock 250 km (155 miles). Effect: raise = more distance is needed before P0461 sets Evidence: ledger:E1046</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36518" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1048575.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2AA" flags="0x0">
    <title>P0461 Check - Level Change Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel level sensor stuck check P0461: the fuel level reading counts as moving, and the check passes, once the spread between its highest and lowest value reaches this much of a full tank. Stock 5.7 %. Effect: raise = the reading must move more to count as not stuck Evidence: ledger:E1046</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3651C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>1171.052044</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/55.9625"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2AB" flags="0x0">
    <title>P0113 / P1111 Check - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intake air temperature sensor circuit high check: samples are only counted once the engine has been running longer than this. Stock 10 s. Effect: raise = the check starts later after a start Evidence: ledger:E1012</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3652C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2AC" flags="0x0">
    <title>P0112 / P1112 Check - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intake air temperature sensor circuit low check: samples are only counted once the engine has been running longer than this. Stock 10 s. Effect: raise = the check starts later after a start Evidence: ledger:E1012</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3652E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2AD" flags="0x0">
    <title>P0112 / P1112 Check - Sensor Resistance Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intake air temperature sensor circuit low check: a sample counts as low when the sensor resistance is below this (a shorted sensor or wire). Stock 25 ohm. Effect: raise = higher resistances already count as a low circuit Evidence: ledger:E1047</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36530" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ohm</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>134217727.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2AE" flags="0x0">
    <title>P0113 / P1111 Check - Sensor Resistance High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intake air temperature sensor circuit high check: a sample counts as high when the sensor resistance is above this (an open sensor or wire). Stock 1.8 Mohm. Effect: lower = lower resistances already count as a high circuit Evidence: ledger:E1047</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36534" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ohm</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>134217727.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2AF" flags="0x0">
    <title>P1112 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intake air temperature sensor circuit low check: P1112 (intermittent) sets once this many low-circuit samples are counted in its longer test window. Stock 100. Effect: raise = more low samples are needed to set P1112 Evidence: ledger:E1012</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36538" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B0" flags="0x0">
    <title>P0112 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intake air temperature sensor circuit low check: P0112 sets once this many low-circuit samples are counted in a test window. Stock 50. Effect: raise = more low samples are needed to set P0112 Evidence: ledger:E1012</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3653A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B1" flags="0x0">
    <title>P1111 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intake air temperature sensor circuit high check: P1111 (intermittent) sets once this many high-circuit samples are counted in its longer test window. Stock 100. Effect: raise = more high samples are needed to set P1111 Evidence: ledger:E1012</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36540" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B2" flags="0x0">
    <title>P0113 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intake air temperature sensor circuit high check: P0113 sets once this many high-circuit samples are counted in a test window. Stock 50. Effect: raise = more high samples are needed to set P0113 Evidence: ledger:E1012</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36542" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B3" flags="0x0">
    <title>P0325 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock sensor circuit check P0325: the code sets once this many samples in a test window show the circuit fault. Stock 40. Effect: raise = more fault samples are needed to set P0325 Evidence: ledger:E1015</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367B0" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B4" flags="0x0">
    <title>P0325 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock sensor circuit check P0325: a test window that reaches this many samples without failing passes. Stock 80. Effect: raise = each test window is longer Evidence: ledger:E1015</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367B1" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B5" flags="0x0">
    <title>P0326 Test - Run Condition, Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0326 knock sensor performance test only runs while engine speed is at or above this. Stock 1800 rpm. Effect: raise = the test needs a higher rpm to run Evidence: ledger:E1015</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B6" flags="0x0">
    <title>Knock Sensor 1 Circuit Low Check Enable (P0327)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the knock sensor 1 circuit low check on or off. 1: the PCM runs the check and can set P0327. 0: the check never runs, so P0327 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0327 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B7" flags="0x0">
    <title>Knock Sensor 2 Circuit Low Check Enable (P0332)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the knock sensor 2 circuit low check on or off. 1: the PCM runs the check and can set P0332. 0: the check never runs, so P0332 is never set and never reported as passed. Stock 0 (off). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0332 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B8" flags="0x0">
    <title>P0327 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock sensor low input check P0327: the code sets once this many samples in a test window show the low input fault. Stock 80. Effect: raise = more fault samples are needed to set P0327 Evidence: ledger:E1015</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367C0" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B9" flags="0x0">
    <title>P0332 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock sensor 2 low input check P0332 (switched off in the stock calibration): the code sets once this many samples in a test window show the low input fault. Stock 80. Effect: raise = more fault samples are needed to set P0332 Evidence: ledger:E1039</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367C1" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2BA" flags="0x0">
    <title>P0327 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock sensor low input check P0327: a test window that reaches this many samples without failing passes. Stock 100. Effect: raise = each test window is longer Evidence: ledger:E1015</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367C2" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2BB" flags="0x0">
    <title>P0332 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock sensor 2 low input check P0332 (switched off in the stock calibration): a test window that reaches this many samples without failing passes. Stock 80. Effect: raise = each test window is longer Evidence: ledger:E1039</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367C3" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2BC" flags="0x0">
    <title>P0103 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAF sensor circuit high check P0103: the code sets once this many samples in a test window read above the high limit. Stock 30. Effect: raise = more high samples are needed to set P0103 Evidence: ledger:E1031</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2BD" flags="0x0">
    <title>P0103 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAF sensor circuit high check P0103: a test window that reaches this many samples without failing passes. Stock 40. Effect: raise = each test window is longer Evidence: ledger:E1031</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2BE" flags="0x0">
    <title>P0102 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAF sensor circuit low check P0102: the code sets once this many samples in a test window read below the low limit. Stock 30. Effect: raise = more low samples are needed to set P0102 Evidence: ledger:E1031</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2BF" flags="0x0">
    <title>P0102 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAF sensor circuit low check P0102: a test window that reaches this many samples without failing passes. Stock 40. Effect: raise = each test window is longer Evidence: ledger:E1031</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C0" flags="0x0">
    <title>P0103 Check - MAF Frequency High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAF sensor circuit high check P0103: a sample counts as high when the MAF output frequency is at or above this. Stock 11000 Hz. Effect: raise = higher frequencies are tolerated before a sample counts as high Evidence: ledger:E1032</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Hz</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>16383.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C1" flags="0x0">
    <title>P0102 Check - MAF Frequency Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAF sensor circuit low check P0102: a sample counts as low when the MAF output frequency is at or below this. Stock 100 Hz. Effect: raise = higher frequencies already count as low Evidence: ledger:E1032</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Hz</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>16383.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C2" flags="0x0">
    <title>MAP Circuit High - P1106 Fail Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit high monitor (P0108, and P1106 for intermittent faults): with the engine running past its arming time, above the engine speed limit at any throttle, or at or below it under the throttle area limit, each MAP sensor reading above the high reading threshold counts as a high sample. The threshold is in raw sensor counts, so it does not follow the MAP sensor gain and offset: on the stock sensor it is about 102.6 kPa, and boost read by the stock sensor sets P0108. For P1106 this is the number of high samples that fails the long window. Stock 640. Effect: raise = more high samples needed to set P1106 Evidence: led...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3681C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C3" flags="0x0">
    <title>MAP Circuit High - P1106 Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit high monitor (P0108, and P1106 for intermittent faults): with the engine running past its arming time, above the engine speed limit at any throttle, or at or below it under the throttle area limit, each MAP sensor reading above the high reading threshold counts as a high sample. The threshold is in raw sensor counts, so it does not follow the MAP sensor gain and offset: on the stock sensor it is about 102.6 kPa, and boost read by the stock sensor sets P0108. For P1106 this is the length of the long window. Stock 6400. Effect: raise = longer P1106 window Evidence: ledger:E0434, ledger:E0889</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3681E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C4" flags="0x0">
    <title>MAP Circuit High - P0108 Fail Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit high monitor (P0108, and P1106 for intermittent faults): with the engine running past its arming time, above the engine speed limit at any throttle, or at or below it under the throttle area limit, each MAP sensor reading above the high reading threshold counts as a high sample. The threshold is in raw sensor counts, so it does not follow the MAP sensor gain and offset: on the stock sensor it is about 102.6 kPa, and boost read by the stock sensor sets P0108. For P0108 this is the number of high samples that sets the code. Stock 320. Effect: raise = more high samples needed to set P0108 Evidence: ledger:E043...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36820" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C5" flags="0x0">
    <title>MAP Circuit High - P0108 Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit high monitor (P0108, and P1106 for intermittent faults): with the engine running past its arming time, above the engine speed limit at any throttle, or at or below it under the throttle area limit, each MAP sensor reading above the high reading threshold counts as a high sample. The threshold is in raw sensor counts, so it does not follow the MAP sensor gain and offset: on the stock sensor it is about 102.6 kPa, and boost read by the stock sensor sets P0108. For P0108 this is the number of samples after which the test passes. Stock 400. Effect: raise = longer P0108 window (keep above the fail count) Evidenc...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36822" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C6" flags="0x0">
    <title>MAP Circuit High - Engine Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit high monitor (P0108, and P1106 for intermittent faults): with the engine running past its arming time, above the engine speed limit at any throttle, or at or below it under the throttle area limit, each MAP sensor reading above the high reading threshold counts as a high sample. The threshold is in raw sensor counts, so it does not follow the MAP sensor gain and offset: on the stock sensor it is about 102.6 kPa, and boost read by the stock sensor sets P0108. This is the engine speed limit. Stock 1100 rpm. Effect: raise = the throttle-limited low-speed test covers a higher engine speed Evidence: ledger:E0434...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36824" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C7" flags="0x0">
    <title>MAP Circuit High - High Reading Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit high monitor (P0108, and P1106 for intermittent faults): with the engine running past its arming time, above the engine speed limit at any throttle, or at or below it under the throttle area limit, each MAP sensor reading above the high reading threshold counts as a high sample. The threshold is in raw sensor counts, so it does not follow the MAP sensor gain and offset: on the stock sensor it is about 102.6 kPa, and boost read by the stock sensor sets P0108. This is the high reading threshold in raw sensor counts (65535 = full scale). Stock 32113, about 102.6 kPa on the stock sensor. With a different s...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36836" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>A/D counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C8" flags="0x0">
    <title>MAP Circuit High - Throttle Area Above Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit high monitor (P0108, and P1106 for intermittent faults): with the engine running past its arming time, above the engine speed limit at any throttle, or at or below it under the throttle area limit, each MAP sensor reading above the high reading threshold counts as a high sample. The threshold is in raw sensor counts, so it does not follow the MAP sensor gain and offset: on the stock sensor it is about 102.6 kPa, and boost read by the stock sensor sets P0108. This is the throttle area below which the test runs above the engine speed limit. Stock 140 % (never reached, so any throttle). Effect: lower = the tes...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36838" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>399.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C9" flags="0x0">
    <title>MAP Circuit High - Throttle Area Below Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit high monitor (P0108, and P1106 for intermittent faults): with the engine running past its arming time, above the engine speed limit at any throttle, or at or below it under the throttle area limit, each MAP sensor reading above the high reading threshold counts as a high sample. The threshold is in raw sensor counts, so it does not follow the MAP sensor gain and offset: on the stock sensor it is about 102.6 kPa, and boost read by the stock sensor sets P0108. This is the throttle area below which the test runs at or below the engine speed limit. Stock 58 %. Effect: lower = the low-speed test stops at a small...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3683A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>399.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2CA" flags="0x0">
    <title>MAP Circuit Low - P1107 Fail Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit low monitor (P0107, and P1107 for intermittent faults): with the ignition on, at or below the engine speed limit, or above it with throttle area at or above the area limit, each MAP sensor reading below the low voltage threshold counts as a low sample. The raw reading does not depend on the MAP sensor gain and offset. For P1107 this is the number of low samples that fails the long window. Stock 640. Effect: raise = more low samples needed to set P1107 Evidence: ledger:E0434, ledger:E0887</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36826" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2CB" flags="0x0">
    <title>MAP Circuit Low - P1107 Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit low monitor (P0107, and P1107 for intermittent faults): with the ignition on, at or below the engine speed limit, or above it with throttle area at or above the area limit, each MAP sensor reading below the low voltage threshold counts as a low sample. The raw reading does not depend on the MAP sensor gain and offset. For P1107 this is the length of the long window. Stock 6400. Effect: raise = longer P1107 window Evidence: ledger:E0434, ledger:E0887</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36828" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2CC" flags="0x0">
    <title>MAP Circuit Low - P0107 Fail Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit low monitor (P0107, and P1107 for intermittent faults): with the ignition on, at or below the engine speed limit, or above it with throttle area at or above the area limit, each MAP sensor reading below the low voltage threshold counts as a low sample. The raw reading does not depend on the MAP sensor gain and offset. For P0107 this is the number of low samples that sets the code. Stock 320. Effect: raise = more low samples needed to set P0107 Evidence: ledger:E0434, ledger:E0887</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3682A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2CD" flags="0x0">
    <title>MAP Circuit Low - P0107 Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit low monitor (P0107, and P1107 for intermittent faults): with the ignition on, at or below the engine speed limit, or above it with throttle area at or above the area limit, each MAP sensor reading below the low voltage threshold counts as a low sample. The raw reading does not depend on the MAP sensor gain and offset. For P0107 this is the number of samples after which the test passes. Stock 400. Effect: raise = longer P0107 window (keep above the fail count) Evidence: ledger:E0434, ledger:E0887</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3682C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2CE" flags="0x0">
    <title>MAP Circuit Low - Engine Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit low monitor (P0107, and P1107 for intermittent faults): with the ignition on, at or below the engine speed limit, or above it with throttle area at or above the area limit, each MAP sensor reading below the low voltage threshold counts as a low sample. The raw reading does not depend on the MAP sensor gain and offset. This is the engine speed limit. Stock 1100 rpm. Effect: raise = the low-throttle test runs up to a higher engine speed Evidence: ledger:E0434, ledger:E0887</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3682E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2CF" flags="0x0">
    <title>MAP Circuit Low - Throttle Area Above Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit low monitor (P0107, and P1107 for intermittent faults): with the ignition on, at or below the engine speed limit, or above it with throttle area at or above the area limit, each MAP sensor reading below the low voltage threshold counts as a low sample. The raw reading does not depend on the MAP sensor gain and offset. This is the throttle area at or above which the test runs above the engine speed limit. Stock 20 %. Effect: raise = the test runs above the speed limit only at larger throttle Evidence: ledger:E0434, ledger:E0887</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36830" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>399.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D0" flags="0x0">
    <title>MAP Circuit Low - Throttle Area Below Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit low monitor (P0107, and P1107 for intermittent faults): with the ignition on, at or below the engine speed limit, or above it with throttle area at or above the area limit, each MAP sensor reading below the low voltage threshold counts as a low sample. The raw reading does not depend on the MAP sensor gain and offset. This is the throttle area at or above which the test runs at or below the engine speed limit. Stock 0 % (any). Effect: raise = the low-speed test needs some throttle Evidence: ledger:E0434, ledger:E0887</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36832" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>399.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D1" flags="0x0">
    <title>MAP Circuit Low - Low Reading Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit low monitor (P0107, and P1107 for intermittent faults): with the ignition on, at or below the engine speed limit, or above it with throttle area at or above the area limit, each MAP sensor reading below the low voltage threshold counts as a low sample. The raw reading does not depend on the MAP sensor gain and offset. This is the low reading threshold in raw sensor counts (65535 = full scale). Stock 328 (0.5 % of full scale). Effect: raise = a higher sensor reading already counts as low Evidence: ledger:E0434, ledger:E0887</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36834" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>A/D counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D2" flags="0x0">
    <title>PCM EEPROM Check Enable (P062F)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the PCM EEPROM check on or off. 1: the PCM runs the check and can set P062F. 0: the check never runs, so P062F is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P062F check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36864" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D3" flags="0x0">
    <title>PCM Keep Alive Memory Check Enable (P0603)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the PCM keep alive memory check on or off. 1: the PCM runs the check and can set P0603. 0: the check never runs, so P0603 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0603 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36866" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D4" flags="0x0">
    <title>PCM Memory Checksum Check Enable (P0601)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the PCM memory checksum check on or off. 1: the PCM runs the check and can set P0601. 0: the check never runs, so P0601 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0601 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36876" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D5" flags="0x0">
    <title>P1380 / P1381 Test - Run Condition, RPM Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P1380 / P1381 test only runs while engine speed is at or below this. Stock 6200 rpm. Effect: raise = the test also runs at higher engine speeds Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D6" flags="0x0">
    <title>P1380 / P1381 Test - Run Condition, Load Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P1380 / P1381 test only runs while the engine load seen by the misfire monitor is at or below this. Stock 100 %. Effect: lower = the test stops running at high load Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D7" flags="0x0">
    <title>Misfire - Single Exceedance Load</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: a catalyst-damaging misfire normally needs three exceedances (or one seen earlier) before P0300 sets. When load at the end of the window is above this, one is enough. Stock 75 %. Effect: raise = the one-exceedance rule needs higher load Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37228" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D8" flags="0x0">
    <title>Misfire - Single Exceedance Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: when engine speed at the end of the window is above this, one catalyst-damaging exceedance is enough to set P0300. Stock 2600 rpm. Effect: raise = the one-exceedance rule needs higher engine speed Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3722A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D9" flags="0x0">
    <title>P2610 - Start Window, Timer Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off timer diagnostic (P2610): the check only starts while the engine-off timer reads at or below this (the timer counts about once a second); a reading outside the start window scores a start failure. Stock 10. Effect: raise = the check may start with a higher timer reading Evidence: ledger:E1039</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3750C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2DA" flags="0x0">
    <title>P2610 - Start Window, Timer Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off timer diagnostic (P2610): the check only starts while the engine-off timer reads at or above this; a reading outside the start window scores a start failure. Stock 0. Effect: raise = the check needs a higher timer reading to start Evidence: ledger:E1039</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3750E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2DB" flags="0x0">
    <title>P2610 - Maximum Time Between Timer Counts</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off timer diagnostic (P2610): a count of the PCM&#x27;s engine-off timer is a good sample only if it comes within this long of the previous count. Stock 1.39 s. Effect: raise = slower timer counts still pass Evidence: ledger:E0829, ledger:E0963</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37512" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2DC" flags="0x0">
    <title>P2610 - Minimum Time Between Timer Counts</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off timer diagnostic (P2610): a count of the PCM&#x27;s engine-off timer is a good sample only if it comes at least this long after the previous count. Stock 0.575 s. Effect: lower = faster timer counts still pass Evidence: ledger:E0829, ledger:E0963</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37514" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2DD" flags="0x0">
    <title>P2610 - Bad Samples to Fail</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off timer diagnostic (P2610): P2610 sets after this many bad samples. Stock 3. Effect: raise = P2610 needs more bad samples to set Evidence: ledger:E0829, ledger:E0963</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37516" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2DE" flags="0x0">
    <title>P2610 - Timer Stall Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off timer diagnostic (P2610): if the engine-off timer does not count for this long, the check scores a bad sample (before the check starts, it retries after this long). Stock 1.39 s. Effect: raise = a stalled timer is noticed later Evidence: ledger:E0829, ledger:E0963</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3751C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2DF" flags="0x0">
    <title>P2610 - Samples to Pass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off timer diagnostic (P2610): the check reports a pass after this many samples. Stock 10. Effect: raise = the check runs longer before it passes Evidence: ledger:E0829, ledger:E0963</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3751E" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E0" flags="0x0">
    <title>P1574 Fail - Deceleration Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): the code sets once this many counted decelerations had the first input change state while the second did not. Stock 5. Effect: raise = more mismatching decelerations are needed to set P1574 Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37538" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E1" flags="0x0">
    <title>P1574 Pass - Deceleration Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): the check passes once this many decelerations have been counted without reaching the fail count. Stock 5. Effect: raise = more counted decelerations are needed for a pass Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37539" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E2" flags="0x0">
    <title>A/C Coolant Overheat Cut - Cut Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The A/C compressor is switched off and kept off once engine coolant temperature rises above this. Stock 122.7 degC. Effect: raise = the A/C keeps running to a higher coolant temperature Evidence: ledger:E1036</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x203C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E3" flags="0x0">
    <title>A/C Coolant Overheat Cut - Re-Enable Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a coolant overheat cut the A/C compressor is allowed again once engine coolant temperature falls below this. Stock 120 degC. Effect: raise = the A/C is allowed again at a higher coolant temperature Evidence: ledger:E1036</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x203C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E4" flags="0x0">
    <title>Fuel Level 2 - Sender Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Second fuel level value (used by the starter low-voltage hold and sent in a data message): how fast its filtered sender voltage follows the raw reading, as the fraction of the gap closed per update. Stock 0.80. Effect: lower = the sender reading is smoothed more (slower to change) Evidence: ledger:E1036</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x207C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E5" flags="0x0">
    <title>Fuel Level 2 - Fast Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Second fuel level value (used by the starter low-voltage hold and sent in a data message): the fraction of the gap closed per update while the fast filter is in use (just after start, in transmission state 6 or 8, or after the fuel level has been low for the low fuel time). Stock 0.10. Effect: lower = the level is smoothed more while the fast filter is in use Evidence: ledger:E1036</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x207C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E6" flags="0x0">
    <title>Fuel Level 2 - Slow Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Second fuel level value (used by the starter low-voltage hold and sent in a data message): the fraction of the gap closed per update while the slow filter is in use (the normal case when driving). Stock 0.004. Effect: lower = the level is smoothed more (slower to change) while driving Evidence: ledger:E1036</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x207C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E7" flags="0x0">
    <title>Fuel Level 2 - Fast Filter Time After Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Second fuel level value (used by the starter low-voltage hold and sent in a data message): the fast filter is always used until the engine has run this long. Stock 8 s. Effect: raise = the fast filter is used for longer after each start Evidence: ledger:E1036</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x207C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E8" flags="0x0">
    <title>Fuel Level 2 - Low Fuel Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Second fuel level value (used by the starter low-voltage hold and sent in a data message): once the fuel level has stayed low for this long the fast filter is used until the level recovers. Stock 60 s. Effect: raise = the level must stay low for longer before the fast filter takes over Evidence: ledger:E1036</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x207CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E9" flags="0x0">
    <title>A/C WOT Cut - Maximum Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: the compressor is held off for at most this long per cut. Stock 0 s, which turns the whole WOT cut off. Effect: raise from 0 = the WOT A/C cut becomes active and can last this long Evidence: ledger:E1009</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x2086E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2EA" flags="0x0">
    <title>A/C WOT Cut - Lockout Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: after a cut ends, another cut cannot start for this long. Stock 0 s. Effect: raise = longer wait between cuts Evidence: ledger:E1009</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x20870" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2EB" flags="0x0">
    <title>A/C WOT Cut - Minimum Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: once started, a cut lasts at least this long even if throttle or rpm leave their limits. Stock 0 s. Effect: raise = each cut lasts longer Evidence: ledger:E1009</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x20874" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2EC" flags="0x0">
    <title>A/C WOT Cut - Release Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: after throttle drops back below the re-enable value, the cut is held this much longer. Stock 1.5 s. Effect: raise = the compressor stays off longer after lifting Evidence: ledger:E1009</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x2087E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2ED" flags="0x0">
    <title>A/C Re-Enable - Refrigerant Pressure High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a high pressure cut, the A/C compressor is allowed again once refrigerant pressure falls below this. Stock 2206 kPa (320 psi). Effect: lower = the compressor stays cut until pressure drops further Evidence: ledger:E1008</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x208A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2EE" flags="0x0">
    <title>A/C Disable - Refrigerant Pressure Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C compressor is cut when refrigerant pressure falls below this. Stock 159 kPa (23 psi). Effect: raise = the compressor is cut at a higher pressure Evidence: ledger:E1008</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x208A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2EF" flags="0x0">
    <title>A/C Re-Enable - Refrigerant Pressure Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a low pressure cut, the A/C compressor is allowed again once refrigerant pressure rises above this. Stock 276 kPa (40 psi). Effect: raise = the compressor stays cut until pressure recovers further Evidence: ledger:E1008</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x208A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F0" flags="0x0">
    <title>Catalyst Over-Temp Protection - Throttle Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst over-temperature protection (catalyst temperature model): the protection enrichment is only applied while commanded throttle (idle share removed) is at or above this. Stock 0 %. Effect: raise = no protection enrichment at small throttle openings Evidence: ledger:E1043</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2186C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F1" flags="0x0">
    <title>Catalyst Over-Temp Protection - Low Throttle Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst over-temperature protection (catalyst temperature model): with protection active and commanded throttle below this, the fixed low throttle EQ replaces the ramped enrichment. An airflow drop freeze can also only start below this throttle. Stock 10 %. Effect: raise = the low throttle handling starts at larger throttle openings Evidence: ledger:E1043</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x21E62" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F2" flags="0x0">
    <title>Catalyst Over-Temp Protection - Low Throttle Exit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst over-temperature protection (catalyst temperature model): the low throttle EQ and an airflow drop freeze both end once commanded throttle reaches this. Stock 15 %. Effect: raise = the low throttle handling is kept to larger throttle openings Evidence: ledger:E1043</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x21E64" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F3" flags="0x0">
    <title>Catalyst Temp Model - Freeze Airflow Drop</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst temperature model: a fall in airflow of at least this much from one update to the next, at low throttle, freezes the model and the over-temperature protection request. Stock 25 g/s. Effect: raise = only a larger sudden airflow drop freezes the model Evidence: ledger:E1043</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x21E66" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F4" flags="0x0">
    <title>Catalyst Temp Model - Freeze Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst temperature model: an airflow drop freeze ends after this long at the latest. Stock 2 s. Effect: raise = the model may stay frozen longer after an airflow drop Evidence: ledger:E1043</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x21E68" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F5" flags="0x0">
    <title>Cruise Control - Vehicle Speed Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: how fast the vehicle speed the cruise controller works from follows the measured speed, as the fraction of the gap closed per update. Stock 0.05. Effect: lower = the cruise speed signal is smoothed more (slower to react) Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21E86" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F6" flags="0x0">
    <title>Cruise Control - Switch Press Time to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: from standby, a cruise switch must have been pressed for at least this long before cruise sets at the current speed. Stock 0.04 s. Effect: raise = the switch must be held longer before cruise sets Evidence: ledger:E1045</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21E92" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F7" flags="0x0">
    <title>Cruise Control - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: an active cruise is cancelled if the engine has run for less than this. Stock 5 s. Effect: raise = cruise cannot stay engaged until later after a start Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21EA4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F8" flags="0x0">
    <title>Cruise Control - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: an active cruise is cancelled when system voltage falls below this. Stock 9 V. Effect: raise = cruise cancels at a higher system voltage Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21EA6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F9" flags="0x0">
    <title>Cruise Control - System Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: an active cruise is cancelled when system voltage rises above this. Stock 18 V. Effect: lower = cruise cancels at a lower system voltage Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21EA8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2FA" flags="0x0">
    <title>Cruise Control - Engage Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: set, resume and the speed tap functions only work while vehicle speed is at or above this. Stock 40 km/h (24.9 mph). Effect: lower = cruise can be set at a lower speed Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21EB0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2FB" flags="0x0">
    <title>Cruise Control - Engage Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: set, resume and the speed tap functions only work while vehicle speed is at or below this. Stock 225 km/h (140 mph). Effect: lower = cruise cannot be set above a lower speed Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21EB2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2FC" flags="0x0">
    <title>Cruise Control - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: an active cruise is cancelled when engine speed falls below this. Stock 500 rpm. Effect: raise = cruise cancels at a higher engine speed Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21EB4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2FD" flags="0x0">
    <title>Cruise Control - RPM Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: an active cruise is cancelled when engine speed rises above this. Stock 6470 rpm. Effect: lower = cruise cancels at a lower engine speed Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21EB6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2FE" flags="0x0">
    <title>Cruise Control - Tap Speed Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: each tap up or tap down changes the set speed by this much. Stock 1.61 km/h (1 mph). Effect: raise = each tap changes the set speed by more Evidence: ledger:E1045</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21EC0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2FF" flags="0x0">
    <title>Idle Speed Control - Integral Maximum, Control</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: largest airflow the integral term may add while holding idle. Stock 2.5 g/s. Effect: raise = the integral may add more air at idle Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x223AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x300" flags="0x0">
    <title>Idle Speed Control - Integral Minimum, Control</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: most airflow the integral term may remove while holding idle. Stock -2.5 g/s. Effect: lower = the integral may remove more air at idle Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x223AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x301" flags="0x0">
    <title>Idle Speed Control - Settle Idle Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: added to desired idle from the start of closed loop idle control until the idle speed has been settled for the settle time. Stock 0 rpm. Effect: raise = idle is held higher until it has settled Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22736" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x302" flags="0x0">
    <title>Idle Speed Control - Settle Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: below this engine speed the settle timer restarts. Stock 450 rpm. Effect: raise = idle counts as settled only above a higher engine speed Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22738" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x303" flags="0x0">
    <title>Idle Speed Control - Settle RPM Error Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: the settle timer runs while the average rpm error is at or below this. Stock 50 rpm. Effect: lower = idle must be closer to target to count as settled Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2273A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x304" flags="0x0">
    <title>Idle Speed Control - Reference Freeze RPM Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: the idle speed reference stops moving toward its target while the rpm error is at or above this and the reference is at or below the freeze reference maximum. Stock 50 rpm. Effect: raise = the reference keeps moving with a larger rpm error Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2273C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x305" flags="0x0">
    <title>Idle Speed Control - Throttle Open Idle Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: added to desired idle while the throttle reads slightly open (see Throttle Open Threshold) and for the hold time after it closes. Stock 0 rpm. Effect: raise = idle target is higher while and just after the driver touches the throttle Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22746" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x306" flags="0x0">
    <title>Idle Speed Control - Integral Update Time, Acquire</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: time between integral steps while engine speed is coming down to idle. Stock 0.025 s (every pass). Effect: raise = the integral steps less often while acquiring idle Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22780" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>1638.375000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/40"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x307" flags="0x0">
    <title>Idle Speed Control - Integral Update Time, Control</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: time between integral steps while holding idle. Stock 0.4 s. Effect: raise = the integral steps less often at idle Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22782" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>1638.375000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/40"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x308" flags="0x0">
    <title>Idle Speed Control - MAP Filter, Control, In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: filter on the manifold pressure the controller&#x27;s airflow model uses, while holding idle in gear; fraction of the change taken every 25 ms. Stock 0.70. Effect: raise = the model follows manifold pressure faster Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22784" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x309" flags="0x0">
    <title>Idle Speed Control - MAP Filter, Control, Park / Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: same filter while holding idle in Park or Neutral. Stock 0.07. Effect: raise = the model follows manifold pressure faster Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22786" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x30A" flags="0x0">
    <title>Idle Speed Control - MAP Filter, Acquire, In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: same filter in the other controller states, in gear. Stock 0.07. Effect: raise = the model follows manifold pressure faster Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22788" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x30B" flags="0x0">
    <title>Idle Speed Control - MAP Filter, Acquire, Park / Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: same filter in the other controller states, in Park or Neutral. Stock 0.07. Effect: raise = the model follows manifold pressure faster Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2278A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x30C" flags="0x0">
    <title>Idle Speed Control - RPM Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: filter on the engine speed the controller uses; fraction of the change taken at each update. Stock 0.75. Effect: lower = the controller sees a smoother engine speed Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2278C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x30D" flags="0x0">
    <title>Idle Speed Control - Throttle Open Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: share of each new throttle reading taken into the filtered throttle area used for the throttle open flag. Stock 0.25. Effect: raise = the flag follows the throttle faster Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2278E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x30E" flags="0x0">
    <title>Idle Speed Control - Throttle Open Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: filtered throttle area above the idle area at or above this counts as the driver being on the throttle: the idle integral may not step down and the throttle open idle offset applies. Stock 0.64 %. Effect: raise = more throttle is needed before the controller treats it as driver input Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22790" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x30F" flags="0x0">
    <title>Idle Speed Control - A/C Hold Airflow Decay Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: the extra airflow held when the A/C clutch engages is removed by this much every 12.5 ms once its hold time is over. Stock 0.052 g/s (about 4.1 g/s per second). Effect: raise = the A/C hold airflow is removed faster Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22796" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x310" flags="0x30">
    <title>Idle A/C Turn-On Airflow Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the extra idle airflow added when the A/C compressor turns on is held at full value before the decay step starts removing it. Stock 0.40 s. Effect: raise = the A/C turn-on airflow is held longer before it starts to decay Evidence: ledger:E0776, ledger:E1221</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>field</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x227E0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x311" flags="0x0">
    <title>Cam Alternate Mode - Minimum Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine run time that must be exceeded before the cam alternate mode can switch on (with engine speed at 8100 rpm or more in idle spark mode). In the mode the desired exhaust cam angle comes from the alternate mode curve and factors. Stock 3.0 s. Dormant: the stock calibration never reaches that speed in idle spark mode, so it has no effect on this truck&#x27;s software. Effect: raise = the alternate mode needs longer running before it can switch on Evidence: ledger:E0776, ledger:E0840, ledger:E1229</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22CFA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x312" flags="0x0">
    <title>Cam Target Spark-Limit Reduction - Down Period</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam target reduction while spark is limited: the load-based cam target is multiplied by a factor (1.0 = no change). While spark has been held below its reference spark for half a second, the factor drops by the step down every down period, never below the floor; otherwise it climbs back by the step up every up period. Stock floor is 1.0, so on the stock calibration the factor stays at 1.0. Stock 5 s. Effect: lower = the cam target is reduced faster while spark is limited Evidence: ledger:E0720, ledger:E0875</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x23064" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x313" flags="0x0">
    <title>Charge Temperature - Start-Up Coolant Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Charge temperature model (used by the VE airflow model and the VE Maximum airmass cap): the charge temperature moves toward intake air temperature plus a fraction of the coolant-to-intake difference, the fraction set by airflow (more airflow, closer to intake temperature), through a lag filter whose speed is also set by airflow. At start the charge temperature is set to intake temperature plus this fraction of the coolant-to-intake difference. Stock 0.8. Effect: raise = charge temperature starts closer to coolant temperature Evidence: ledger:E0776, ledger:E0878</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2311C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain (fraction x65536)</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x314" flags="0x0">
    <title>Long Soak Start - Count Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of counted long-soak starts at which the long-soak start status flag is set (stock 1). A start counts when the engine-off time is above the minimum engine-off time for the coolant temperature at power-up. Effect: raise = more qualifying starts are needed before the flag sets Evidence: ledger:E0221, ledger:E0776, ledger:E1455</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23126" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>starts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x315" flags="0x0">
    <title>Per-Cylinder Learn Table RPM Enable Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per-cylinder learn: the per-cylinder learn and blend block runs only while engine speed is at or above this. Stock 420 rpm. Effect: raise = the per-cylinder learn needs a higher engine speed before it runs Evidence: ledger:E0775, ledger:E1259</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x23A90" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x316" flags="0x0">
    <title>High-Load Monitor - Intake Vacuum Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. High-load monitor: its timer runs only while intake vacuum is below this (high engine load); at or above it the timer starts again from zero. Stock 5.0 kPa. Effect: raise = more engine operation counts as high load Evidence: ledger:E0775, ledger:E1265</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23C56" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x317" flags="0x0">
    <title>Pedal Gain Reduction - Torque Sample Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How far back the driveline output torque sample used for the acceleration threshold row is taken, in 0.05 s steps (0 to 0.3 s; higher values act as 0.3 s). Stock 0 (current torque). Effect: raise = the threshold uses an older driveline torque sample Evidence: ledger:E0775, ledger:E1203</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23E04" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x318" flags="0x0">
    <title>Pedal Gain Reduction - Traction Control Immediate Start Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While traction control is cutting torque and the truck accelerates at or above the pedal gain reduction acceleration threshold, the reduction starts at once, without waiting the Confirm Time, when the traction control torque limit is below this share of the net engine torque. Stock 0.05 (5 percent). Range 0 to 1.0. Effect: raise = milder traction control torque cuts also start the pedal gain reduction at once Evidence: ledger:E0781, ledger:E0918, ledger:E1203, ledger:E1207</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23EAC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x319" flags="0x30">
    <title>Pedal Throttle Request Factor by Transmission State</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the driver&#x27;s pedal throttle request, by transmission state (1st to 4th gear, Neutral, Reverse, Park; the two 5th / 6th entries are not used on this 4-speed). The PCM multiplies the pedal map&#x27;s throttle request by this and several other factors. 1.0 = no change; lower = less throttle for the same pedal. Stock 1.0 in every state. Effect: lower = less throttle for the same pedal in that gear or range Evidence: ledger:E0240, ledger:E0775, ledger:E0947, ledger:E1196</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>transmission state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="5th (unused)" />
      <LABEL index="5" value="6th (unused)" />
      <LABEL index="6" value="Neutral" />
      <LABEL index="7" value="Reverse" />
      <LABEL index="8" value="Park" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23F5E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x31A" flags="0x0">
    <title>Pedal Gain Increase - Transmission State</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission state (0-3 = 1st-4th, 6 Neutral, 7 Reverse, 8 Park) the pedal gain increase learn requires, used only when the Ignore Transmission State switch is 0. Stock 0 (1st), switch stock 1, so it is not used. Effect: selects the one transmission state the learn runs in, when the state match is enabled Evidence: ledger:E0436, ledger:E1211, ledger:E1577</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23FC2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>state</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x31B" flags="0x0">
    <title>Pedal Gain Increase - Ignore Transmission State</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Switch: 1 lets the pedal gain increase learn run in any transmission state, 0 limits it to the Transmission State word. Stock 1. Effect: 0 = the learn runs only in the Transmission State word&#x27;s state Evidence: ledger:E0775, ledger:E1211, ledger:E1577</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23FF8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x31C" flags="0x30">
    <title>Pedal Map Select vs Trans State - 4WD-Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Which pedal to throttle map is used in each transmission state in 4WD-Low: 0 = 4WD-Low forward gears map, 1 = 4WD-Low Park/Neutral map, 2 = 4WD-Low Reverse map. Stock 1 in Neutral and Park, 2 in Reverse, 0 elsewhere. The choice changes only while the pedal is at rest or wide open. Allowed values are 0, 1 and 2 only; any other value makes the pedal read the wrong map or no map. Effect: changes which 4WD-Low pedal map is used in that transmission state Evidence: ledger:E0240, ledger:E0781, ledger:E1210</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>transmission state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="Neutral" />
      <LABEL index="7" value="Reverse" />
      <LABEL index="8" value="Park" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24B26" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>map slot</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x31D" flags="0x0">
    <title>Pedal Response Change - Wide Open Pedal Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal response changes (pedal map selection and any raise of the pedal request factor) are only taken while the pedal is at rest or wide open. The pedal counts as wide open above this position while manifold vacuum is below the Wide Open Vacuum Threshold vs RPM. Stock 90 %. Effect: lower = less pedal is needed to count as wide open, so pedal response changes are taken more readily Evidence: ledger:E0781, ledger:E1118, ledger:E1209</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x24B4A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x31E" flags="0x0">
    <title>Pedal Response Change - Pedal At Rest Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal response changes (pedal map selection and any raise of the pedal request factor) are only taken while the pedal is at rest or wide open. The pedal counts as at rest at or below this position. Stock 1.0 %. Effect: raise = the pedal counts as at rest further into its travel, so pedal response changes are taken more readily Evidence: ledger:E0781, ledger:E1118, ledger:E1209</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x24B70" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x31F" flags="0x0">
    <title>Pedal Map Speed Input - Minimum Rise Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest rate at which the vehicle speed used by the pedal map may rise toward the actual speed. The rise rate is the larger of this and the pedal gain reduction acceleration threshold; a drop in speed is followed at once. Stock 128 km/h/s (the largest value), so the speed input follows within an update or two. At 0 with a zero threshold the speed input stops rising. Range 0 to 128. Effect: lower = the pedal map&#x27;s speed input lags behind a rising vehicle speed Evidence: ledger:E0775, ledger:E1203, ledger:E1210, ledger:E1213</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x24BAC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x320" flags="0x0">
    <title>Accelerator Pedal Filter - Gain Hold Gap</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal gap above which the filter keeps the highest gain reached instead of following the gain tables down, until the gap shrinks or the pedal changes direction. Stock 2.3 %. Part of the accelerator pedal filter: the filtered pedal closes this share of its gap to the pedal demand every update; 1.0 follows the pedal at once. Effect: raise = the filter gain follows the gap tables up to a larger gap before holding Evidence: ledger:E0330, ledger:E0781, ledger:E1190</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x24DBE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% (pedal gap)</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>95.998066</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/682.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x321" flags="0x0">
    <title>Pedal Filter - Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal filter: share of the gap between the pedal demand and its filtered value that is closed every 12.5 ms. It is the lowest gain the filter may use, and on the stock file it is the gain at all times. Stock 0.8. Effect: lower = softer, slower pedal response; 1.0 = no filtering Evidence: ledger:E1118</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x24EE8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x322" flags="0x0">
    <title>Pedal Position - Dead Band at Rest</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal: pedal travel above the learned rest position that still reads as 0 % pedal. Stock 3 %. Effect: raise = more free travel before the pedal starts to act Evidence: ledger:E1120</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x24F10" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x323" flags="0x0">
    <title>Pedal Position - Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal: highest pedal value passed on to the pedal map. Stock 100 %: no limit. Effect: lower = the pedal map never sees more than this pedal position Evidence: ledger:E1120</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x24F12" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x324" flags="0x0">
    <title>Purge Trim Feedback - Trim Above Which Purge May Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, fuel trim feedback: while the applied long term fuel trim is above this, the purge trim factor steps up (purge is not pulling much fuel out of the trim). Stock 0.85. Effect: raise = purge is held back until the trim is closer to 1.0 Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x250F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x325" flags="0x0">
    <title>Purge Trim Feedback - Trim Below Which Purge Falls</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, fuel trim feedback: while the applied long term fuel trim is at or below this, the purge trim factor steps down. Stock 0.82. Effect: raise = purge is cut back at a smaller fuel trim correction Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x250F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x326" flags="0x0">
    <title>Purge Trim Feedback - Factor Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, fuel trim feedback: amount the purge trim factor moves on each update. Stock 0.001. Effect: raise = the purge trim factor moves faster Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x250F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x327" flags="0x0">
    <title>Purge Trim Feedback - Factor Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, fuel trim feedback: highest value of the purge trim factor. Stock 1.0. Effect: lower = less purge even with a healthy fuel trim Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x250F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x328" flags="0x0">
    <title>Purge Trim Feedback - Factor Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, fuel trim feedback: lowest value of the purge trim factor. Stock 0.5. Effect: raise = purge is cut back less when the trim is pulling fuel Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x250F8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x329" flags="0x0">
    <title>Purge Trim Feedback - Factor at Key-On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, fuel trim feedback: value of the purge trim factor at key-on. Stock 1.0. Effect: lower = each trip starts with less purge Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x250FA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x32A" flags="0x0">
    <title>Purge O2 Feedback - Rich Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: front O2 voltage at or above this counts as rich and steps the purge factor (1.0 = full purge request) down. Stock 750 mV. Effect: raise = a richer mixture is needed before purge is cut back Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25124" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x32B" flags="0x0">
    <title>Purge O2 Feedback - Lean Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: front O2 voltage below this counts as lean and steps the purge factor (1.0 = full purge request) up. Between the lean and rich voltages the factor holds. Stock 450 mV. Effect: lower = a leaner mixture is needed before purge is increased Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25126" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x32C" flags="0x0">
    <title>Purge O2 Feedback - Step Period After Long Rich Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: time between steps of the purge factor once the mixture has been rich longer than the rich time curve. Stock 0.2 s. Effect: raise = slower steps Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25128" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x32D" flags="0x0">
    <title>Purge O2 Feedback - Step Period After the Top Was Reached</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: time between steps up of the purge factor once it has reached its top value on this trip. Stock 0.2 s. Effect: raise = slower steps up later in the trip Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2512A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x32E" flags="0x0">
    <title>Purge O2 Feedback - Step Period</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: normal time between steps of the purge factor. Stock 0.2 s. Effect: raise = slower steps Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2512C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x32F" flags="0x0">
    <title>Purge O2 Feedback - Step Down After Long Rich Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: step down of the purge factor once the mixture has been rich longer than the rich time curve. Stock 0.015. Effect: raise = purge is cut back faster when the mixture stays rich Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2512E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x330" flags="0x0">
    <title>Purge Flow - Reference Flow Full Scale</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge: value of the purge reference flow that counts as full flow. Long term fuel trim applies the purge learned correction in proportion to the reference flow divided by this. It defines the purge flow units used by the other purge flow curves. Stock 123. Effect: raise = the same reference flow counts as a smaller share of full purge on the fuel trim side Evidence: ledger:E1122</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x251C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flow units</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x331" flags="0x0">
    <title>Purge Amount - Factor Cap</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount: highest value of the combined purge factor (O2 feedback factor times trim factor, after the enrichment multipliers). Stock 1.0: no extra limit. Effect: lower = purge is limited to that share of the full request Evidence: ledger:E1119</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x251F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x332" flags="0x0">
    <title>Purge Amount - Multiplier During Catalyst Protection Enrichment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount: multiplier on the purge factor while catalyst over-temperature enrichment is active. Stock 1.0: no change. Effect: lower = less purge during catalyst protection enrichment Evidence: ledger:E1119</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x251F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x333" flags="0x0">
    <title>Purge Amount - Multiplier During Engine Over-Temperature Enrichment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount: multiplier on the purge factor while coolant over-temperature enrichment is active. Stock 1.0: no change. Effect: lower = less purge during over-temperature enrichment Evidence: ledger:E1119</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x251F8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x334" flags="0x0">
    <title>Purge Amount - Multiplier During Power Enrichment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount: multiplier on the purge factor while power enrichment is active. Stock 1.0: no change. Effect: lower = less purge at wide open throttle Evidence: ledger:E1119</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x251FA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x335" flags="0x0">
    <title>Purge Amount - Tank Vacuum Cap Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount: time the fuel tank vacuum must call for less purge than the factor cap before the tank vacuum cap is applied. Stock 5 s. Effect: raise = the tank vacuum cap acts later Evidence: ledger:E1123</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x251FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x336" flags="0x0">
    <title>Purge Enable - Closed Loop Time Before Purge Resumes</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: time in closed loop fuel control before purge comes back on when it has already run on this trip. Stock 0 s: at once. Effect: raise = purge comes back later after each return to closed loop Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x252FA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x337" flags="0x0">
    <title>Purge Enable - Run Time That Waives the First Purge Speed and Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: once the engine has run longer than this, the first purge of a trip no longer needs the minimum speed and airflow. Stock 0 s, so those two conditions never apply. Effect: raise = the first purge of a trip waits for the minimum speed and airflow until the engine has run this long Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25324" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x338" flags="0x0">
    <title>Purge Enable - Speed to Unblock</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: once purge has been blocked by low throttle or low speed, it is released when speed is at or above this (or throttle at or above its unblock value). Stock 0: this condition is off. Effect: raise = purge stays blocked up to a higher speed Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25350" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x339" flags="0x0">
    <title>Purge Enable - Speed Below Which Purge Is Blocked</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: purge is blocked when vehicle speed is below this or throttle is below its block value. Stock 0: this condition is off. Effect: raise = purge is blocked at low speed Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25352" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x33A" flags="0x0">
    <title>Purge Enable - First Purge Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: lowest vehicle speed for the first purge of a trip, used only until the engine has run longer than the waiver run time. Stock 15 km/h, but the waiver run time is 0, so it does not apply. Effect: raise = the first purge of a trip needs more road speed (only with a waiver run time above 0) Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25354" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x33B" flags="0x0">
    <title>Purge Enable - Throttle to Unblock</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: once purge has been blocked, it is released when throttle is at or above this (or speed at or above its unblock value). Stock 0: this condition is off. Effect: raise = purge stays blocked up to more throttle Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25356" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x33C" flags="0x0">
    <title>Purge Enable - Throttle Below Which Purge Is Blocked</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: purge is blocked when throttle is below this or speed is below its block value. Stock 0: this condition is off. Effect: raise = purge is blocked at small throttle openings Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25358" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x33D" flags="0x0">
    <title>Purge Enable - MAP On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: purge may switch on only with manifold pressure above this. Stock 14 kPa. Effect: raise = purge needs more manifold pressure to switch on Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2535A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x33E" flags="0x0">
    <title>Purge Enable - MAP Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: purge switches off when manifold pressure is at or below this. Stock 12 kPa. Effect: raise = purge switches off at a higher manifold pressure Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2535C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x33F" flags="0x0">
    <title>Purge Enable - First Purge Airflow Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: lowest engine airflow for the first purge of a trip, used only until the engine has run longer than the waiver run time. Stock 8 g/s, but the waiver run time is 0, so it does not apply. Effect: raise = the first purge of a trip needs more airflow (only with a waiver run time above 0) Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2535E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x340" flags="0x30">
    <title>Start-Up Fuel - Pulse Multiplier vs Pre-Sync Restarts</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the start-up fuel pulses of the pre-sync pulse sequence by how many times the sequence has restarted without gaining crank / cam sync (0 to 5). Not applied above 150 C coolant. The pre-sync sequence is switched off on the stock H3 and every value is 0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (raise = larger pre-sync pulses after that many restarts) Evidence: ledger:E0436, ledger:E1282</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>restarts</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25582" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x341" flags="0x0">
    <title>LTFT Purge Cell Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: commanded purge at or above this selects the purge set of trim cells (0 to 20); below it the non purge set (21 to 38) is used. Stock 2.1 %. Effect: raise = the non purge cells are used up to a higher purge level Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25672" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x342" flags="0x0">
    <title>LTFT Floor During Enrichment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: lowest long term trim applied while enrichment is requested. Stock 1.0, so a trim that removes fuel is not applied during enrichment. Effect: lower = a fuel-removing long term trim is also applied during enrichment Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2568E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x343" flags="0x0">
    <title>Purge Learned Memory Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: lowest value of the purge learned memory (the extra correction learned for canister purge; 1.0 = none). Stock 0.82. Effect: raise = less fuel can be removed for purge vapour Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25690" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x344" flags="0x30">
    <title>LTFT Learn Step - Idle and Closed Throttle Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: size of one learn step in the idle and closed throttle cells. Stock 0.40 % in each. Effect: raise = these cells learn in larger steps Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>cell</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="idle stopped, Park / Neutral, A/C off, purge on" />
      <LABEL index="1" value="idle stopped, in gear, A/C off, purge on" />
      <LABEL index="2" value="idle stopped, Park / Neutral, A/C on, purge on" />
      <LABEL index="3" value="idle stopped, in gear, A/C on, purge on" />
      <LABEL index="4" value="closed throttle moving, purge on" />
      <LABEL index="5" value="idle stopped, purge off" />
      <LABEL index="6" value="closed throttle moving, purge off" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x256A8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x345" flags="0x0">
    <title>Purge Learned Memory Step Up</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: amount the purge learned memory moves back toward 1.0 per learn step when the mixture is lean in a purge cell. Stock 1.0 %. Effect: raise = the purge correction is removed faster Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x256B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x346" flags="0x0">
    <title>Purge Learned Memory Step Down</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: amount the purge learned memory drops per learn step when the mixture is rich and the purge cell has reached its learn-down limit. Stock 1.0 %. Effect: raise = the purge correction is learned faster Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x256B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x347" flags="0x30">
    <title>LTFT Learn Step - Purge Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: size of one learn step in the 16 grid cells used with purge on, by engine speed zone and MAP zone. Stock 0.40 % in each. Effect: raise = these cells learn in larger steps Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>engine speed zone</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="up to 100 rpm" />
      <LABEL index="1" value="100 to 6000 rpm" />
      <LABEL index="2" value="6000 to 6500 rpm" />
      <LABEL index="3" value="above 6500 rpm" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>MAP zone</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="up to 5 kPa" />
      <LABEL index="1" value="5 to 60 kPa" />
      <LABEL index="2" value="60 to 110 kPa" />
      <LABEL index="3" value="above 110 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x256BA" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x348" flags="0x30">
    <title>LTFT Learn Step - Non Purge Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: size of one learn step in the 16 grid cells used with purge off, by engine speed zone and MAP zone. Stock 0.40 % in each. Effect: raise = these cells learn in larger steps Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>engine speed zone</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="up to 100 rpm" />
      <LABEL index="1" value="100 to 6000 rpm" />
      <LABEL index="2" value="6000 to 6500 rpm" />
      <LABEL index="3" value="above 6500 rpm" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>MAP zone</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="up to 5 kPa" />
      <LABEL index="1" value="5 to 60 kPa" />
      <LABEL index="2" value="60 to 110 kPa" />
      <LABEL index="3" value="above 110 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x256DA" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x349" flags="0x30">
    <title>LTFT Purge Cells - Learn Down Limit per Trip</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim, purge cells 0 to 20: how far below its stored value a cell may learn during one trip. Once a cell is at that limit, further rich correction goes to the purge learned memory instead. Stock 18 % (13 % in cells 16 to 20). Effect: raise = a purge cell may learn further down in one trip before the purge learned memory takes over Evidence: ledger:E1107</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>cell</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x256FA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x34A" flags="0x0">
    <title>LTFT Store - Coolant Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: the non purge cells are copied to the stored (keep-alive) values only below this coolant temperature. Stock 120 C. Effect: raise = learned values are stored at higher coolant temperature Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2576E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x34B" flags="0x0">
    <title>LTFT Store - Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: and only above this coolant temperature. Stock 40 C. Effect: lower = learned values are stored on a colder engine Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25770" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x34C" flags="0x0">
    <title>LTFT Store - Maximum, Non Purge Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: highest value stored for the non purge cells. Stock 1.25. Effect: raise = a larger fuel-adding trim can be stored Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25772" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x34D" flags="0x0">
    <title>LTFT Store - Minimum, Idle Non Purge Cell</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: lowest value stored for the idle non purge cell. Stock 0.85. Effect: lower = a larger fuel-removing trim can be stored Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25774" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x34E" flags="0x0">
    <title>LTFT Store - Minimum, Closed Throttle Non Purge Cell</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: lowest value stored for the closed throttle moving non purge cell. Stock 0.85. Effect: lower = a larger fuel-removing trim can be stored Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25776" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x34F" flags="0x0">
    <title>LTFT Store - Minimum, Non Purge Grid Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: lowest value stored for the 16 non purge grid cells. Stock 0.85. Effect: lower = a larger fuel-removing trim can be stored Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25778" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x350" flags="0x0">
    <title>LTFT Store - Maximum, Purge Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: highest value stored for the purge cells. Stock 1.25. Effect: raise = a larger fuel-adding trim can be stored Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2577A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x351" flags="0x0">
    <title>LTFT Store - Minimum, Purge Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: lowest value stored for the purge cells. Stock 0.85. Effect: lower = a larger fuel-removing trim can be stored Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2577C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x352" flags="0x0">
    <title>Purge Learned Memory Recovery Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: amount the purge learned memory is moved back toward 1.0 at each start of a full fuel cut. Stock 10 %. Effect: raise = the purge correction recovers faster on deceleration Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2577E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x353" flags="0x0">
    <title>LTFT MAP Change Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: filter on the manifold pressure used to measure the MAP change for the follow rate curve. Stock 1.0 (no filtering). Effect: lower = the MAP change is measured against a slower moving average Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25780" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x354" flags="0x0">
    <title>LTFT Learn Follow Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: a cell learns only while the applied long term trim is within this of the cell value. Stock 5 %. Effect: raise = learning continues while the applied trim is further from the cell value Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25796" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x355" flags="0x0">
    <title>Rear O2 Trim - Learn Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: the learned switch point offset is updated only at or above this coolant temperature. Stock 80 C. Effect: raise = the offset is learned only on a warmer engine Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2579A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x356" flags="0x0">
    <title>Rear O2 Trim - Rear O2 Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: filter on the rear oxygen sensor voltage used by this trim; each 100 ms the filtered value moves this fraction of the way to the new reading. Stock 0.05. Effect: raise = the trim follows the rear sensor faster Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2579C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x357" flags="0x0">
    <title>Rear O2 Trim - Learn Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: amount the learned switch point offset moves per learn interval. Stock 0.19 mV. Effect: raise = the offset is learned faster Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x257C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x358" flags="0x0">
    <title>Rear O2 Trim - Rear O2 Rate Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: filter on the rear oxygen sensor signal used to measure how fast it is moving (the input of the adder by rear O2 rate). Stock 0.10 per 100 ms. Effect: raise = the rate input reacts faster Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x257CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x359" flags="0x0">
    <title>Rear O2 Trim - Adder Idle Throttle Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: the idle factor applies only with the throttle area above the idle area below this (and below the idle speed limit). Stock 1.5 %. Effect: raise = the idle factor also applies with the throttle a little open Evidence: ledger:E1107</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x257D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x35A" flags="0x0">
    <title>Rear O2 Trim - Adder Idle Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: factor applied to the adder by rear O2 voltage at idle (low throttle and below the idle speed limit). Stock 0.80. Effect: raise = more of the adder is applied at idle Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x257D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x35B" flags="0x0">
    <title>Rear O2 Trim - Adder Idle Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: the idle factor applies below this vehicle speed. Stock 3 km/h. Effect: raise = the idle factor applies up to a higher speed Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x257D4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x35C" flags="0x0">
    <title>Rear O2 Trim - Sensor Active Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: the rear sensor counts as active once its filtered voltage has been outside the not-active band for this long in total. Stock 1 s. Effect: raise = the rear sensor must show activity longer before the trim works Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x258F6" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x35D" flags="0x0">
    <title>Rear O2 Trim - Not Active Band, High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: upper edge of the rear sensor not-active band; a reading at or above it counts toward the active time. Stock 550 mV. Effect: raise = a richer reading is needed to count as activity Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x258F8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x35E" flags="0x30">
    <title>Closed Loop Trim Jump - Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. These two values are the jump in closed-throttle idle: first while the O2 reads lean (trim steps up), second while it reads rich (trim steps down). Stock 0.40 % each. Effect: raise = bigger trim step at each O2 switch Evidence: ledger:E0433, ledger:E0903</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>O2 state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="lean" />
      <LABEL index="1" value="rich" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25946" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x35F" flags="0x30">
    <title>Closed Loop Trim Jump - Off Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. These two values are the jump off idle: first while the O2 reads lean, second while it reads rich. Stock 0.40 % each. Effect: raise = bigger trim step at each O2 switch Evidence: ledger:E0433, ledger:E0903</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>O2 state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="lean" />
      <LABEL index="1" value="rich" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2594A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x360" flags="0x30">
    <title>Closed Loop Trim Jump - Unused Modes (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. Inactive on the stock calibration: these jumps belong to closed-loop modes the mode selector never chooses with stock values. Effect: no effect on the stock calibration Evidence: ledger:E0433, ledger:E0903</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>12</indexcount>
      <units>mode / O2 state</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2592E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="12" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x361" flags="0x0">
    <title>Closed Loop Low Baro Mode - Barometric Pressure Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): below this barometric pressure the short term trim uses its second set of steps and delays (the mode 2 values of the unused modes items). Stock 0 kPa: never. Effect: raise = the second set is used below that barometric pressure Evidence: ledger:E1107</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25956" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x362" flags="0x0">
    <title>Closed Loop Coolant Window Mode - Coolant Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel, coolant window mode: the short term trim uses a separate set of gains while coolant is inside a window and the engine has run for less than a set time. Dormant on the stock calibration: the run time is 0, so the mode is never selected. This is the lower edge of the window: coolant must be above it. Stock 138 C. Effect: lower = the window starts at a lower coolant temperature Evidence: ledger:E1134</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25964" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x363" flags="0x0">
    <title>Closed Loop Coolant Window Mode - Coolant Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel, coolant window mode: the short term trim uses a separate set of gains while coolant is inside a window and the engine has run for less than a set time. Dormant on the stock calibration: the run time is 0, so the mode is never selected. This is the upper edge of the window: coolant must be below it. Stock 140 C. Effect: raise = the window reaches a higher coolant temperature Evidence: ledger:E1134</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25966" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x364" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling - Cold Coolant Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this coolant temperature the cold Proportional Term Ceiling Factors are used in 1st gear and in 2nd, Neutral, Reverse and Park. Stock 45.5 C. Effect: raise = the cold factors are used up to a higher coolant temperature Evidence: ledger:E0436, ledger:E1134, ledger:E1216</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25968" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>C</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x365" flags="0x0">
    <title>STFT Idle Return Reset - Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: the idle return reset works only at or above this coolant temperature. Stock 50 C. Effect: raise = the reset needs a warmer engine Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2596A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x366" flags="0x0">
    <title>STFT Idle Return Reset - Arm RPM Above Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: the idle return reset is armed when engine speed is more than this above desired idle. Stock 200 rpm. Effect: raise = the reset is armed only from a higher engine speed Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2596C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x367" flags="0x0">
    <title>STFT Idle Return Reset - Fire RPM Above Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: once armed, the reset fires when engine speed comes back to less than this above desired idle with the trim integrator below the reset threshold: the integrator is set to 1.0. Stock 10 rpm. Effect: raise = the reset fires earlier on the way down to idle Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2596E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x368" flags="0x0">
    <title>Closed Loop Proportional Term - Multiplier Before Closed Loop Is Enabled</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim before closed loop is enabled: once the O2 sensor is ready but the coolant and run time conditions for closed loop are not yet met, the O2 trim already runs on top of open loop fuelling, and its proportional term is multiplied by this. Stock 1.0. Effect: lower = a gentler O2 correction in the phase before closed loop Evidence: ledger:E1140</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25970" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x369" flags="0x0">
    <title>STFT Integrator Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: highest value of the trim integrator (1.0 = no correction). Stock 1.31. Effect: raise = short term trim can add more fuel Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2598C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x36A" flags="0x0">
    <title>STFT Integrator Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: lowest value of the trim integrator. Stock 0.80. Effect: lower = short term trim can remove more fuel Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2598E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x36B" flags="0x0">
    <title>STFT Open Loop Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: highest integrator value kept while open loop. Stock 1.0; with the open loop minimum also 1.0 the integrator is reset to 1.0 whenever the system goes open loop. Effect: raise = a fuel-adding trim is kept through open loop Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25990" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x36C" flags="0x0">
    <title>STFT Idle Return Reset - Integrator Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: the idle return reset fires only when the trim integrator is below this. Stock 1.0. Effect: lower = only a larger fuel-removing trim is reset on the return to idle Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25992" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x36D" flags="0x0">
    <title>STFT Open Loop Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: lowest integrator value kept while open loop. Stock 1.0. Effect: lower = a fuel-removing trim is kept through open loop Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25994" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x36E" flags="0x0">
    <title>Closed Loop Coolant Window Mode - Engine Run Time Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel, coolant window mode: the short term trim uses a separate set of gains while coolant is inside a window and the engine has run for less than a set time. Dormant on the stock calibration: the run time is 0, so the mode is never selected. This is the run time: the mode is only used while the engine has run for less than this. Stock 0 s, which switches the mode off. Effect: raise = the coolant window mode is used for that long after a start Evidence: ledger:E1134</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25996" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x36F" flags="0x30">
    <title>Closed Loop O2 Filter Gain - Rich / Lean Decision</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): filter on the O2 voltage that is compared with the switch point to decide rich or lean, by airflow. Share of each new reading taken every 12.5 ms. Stock 0.5 at idle and 1.0 (no filtering) off idle. Effect: lower = the rich / lean decision reacts more slowly to the O2 sensor Evidence: ledger:E1126</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s used airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4.8" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="13.2" />
      <LABEL index="4" value="21.8" />
      <LABEL index="5" value="29.5" />
      <LABEL index="6" value="40.3" />
      <LABEL index="7" value="51.8" />
      <LABEL index="8" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x259F0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x370" flags="0x0">
    <title>Closed Loop Slow-Sensor Tables - Response Time Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel, slow sensor tables: once the slow sensor tables are in use, this is added to the measured O2 response times before they are classed again, so the tables are not left on a marginal improvement. Stock 3.9 ms. Effect: raise = the slow sensor tables are kept for longer once selected Evidence: ledger:E1126</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25C2C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ms</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>63999.023438</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1.024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x371" flags="0x30">
    <title>Closed Loop Alternate Tables Map - O2 Lean (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this map would turn on the slow-sensor tables while the O2 reads lean, and it is all zero. Rows are the lean-to-rich response time and columns the rich-to-lean response time (the opposite of the rich map). Effect: no effect on the stock calibration Evidence: ledger:E0433, ledger:E0904, ledger:E1126</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rich-to-lean time (ms)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="29" />
      <LABEL index="1" value="39" />
      <LABEL index="2" value="49" />
      <LABEL index="3" value="59" />
      <LABEL index="4" value="69" />
      <LABEL index="5" value="79" />
      <LABEL index="6" value="89" />
      <LABEL index="7" value="99" />
      <LABEL index="8" value="109" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>lean-to-rich time (ms)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="29" />
      <LABEL index="1" value="39" />
      <LABEL index="2" value="49" />
      <LABEL index="3" value="59" />
      <LABEL index="4" value="69" />
      <LABEL index="5" value="79" />
      <LABEL index="6" value="89" />
      <LABEL index="7" value="99" />
      <LABEL index="8" value="109" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25C34" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flag</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x372" flags="0x30">
    <title>Closed Loop Alternate Tables Map - O2 Rich</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). This map turns on the slow-sensor tables while the O2 reads rich (1 = on), by measured rich-to-lean time (rows) and lean-to-rich time (columns), about 10 ms per step from 29 ms. Stock on only when rich-to-lean is 89 ms or slower and lean-to-rich is much faster. Effect: 1 = slow-sensor tables on for that response Evidence: ledger:E0433, ledger:E0904</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>lean-to-rich time (ms)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="29" />
      <LABEL index="1" value="39" />
      <LABEL index="2" value="49" />
      <LABEL index="3" value="59" />
      <LABEL index="4" value="69" />
      <LABEL index="5" value="79" />
      <LABEL index="6" value="89" />
      <LABEL index="7" value="99" />
      <LABEL index="8" value="109" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rich-to-lean time (ms)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="29" />
      <LABEL index="1" value="39" />
      <LABEL index="2" value="49" />
      <LABEL index="3" value="59" />
      <LABEL index="4" value="69" />
      <LABEL index="5" value="79" />
      <LABEL index="6" value="89" />
      <LABEL index="7" value="99" />
      <LABEL index="8" value="109" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25C8C" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flag</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x373" flags="0x0">
    <title>Per Cylinder Fuel Multipliers - Switch (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per cylinder fuel multipliers: 0 = not applied (stock). 1 = applied at all engine speeds; fuel is then also calculated per cylinder above about 5000 rpm, where stock uses one value for all cylinders. Any other value = applied below about 5000 rpm only. Note that the stock multiplier values are 0.9995, not exactly 1. Effect: 1 = the per cylinder multipliers take effect Evidence: ledger:E1141</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26048" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>code</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x374" flags="0x0">
    <title>Fuel Injected Since Start - Count Scale (do not edit)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sets how much injected fuel one count of the fuel injected since start value represents; that value is the row input of the start-up open-loop fuel tables. Stock 22.28 mg per count (65,535 counts = 1.46 kg, after which the count wraps). Changing it rescales those tables&#x27; fuel axis, so leave it at stock. Effect: do not edit: it changes the meaning of the start-up fuel table axis Evidence: ledger:E0436, ledger:E1468</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x266FE" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>mg per count</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>32.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/134217728"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x375" flags="0x0">
    <title>Transient Fuel - Wall Film Mass Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transient fuel: largest fuel mass the wall film model of a cylinder may hold. Stock 2048 mg, the largest value the film can take anyway, so it does not limit. Effect: lower = the modelled wall film is capped, which shortens tip-in and tip-out corrections Evidence: ledger:E1139</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26702" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>mg</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>2047.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x376" flags="0x0">
    <title>Acceleration Fuel Adder - Fuel Rise Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra fuel on acceleration: the calculated fuel of a cylinder must rise by at least this from one injection to the next before the rise adds to the adder. Stock 2.75 mg. Dormant on the stock calibration: the adder gain curve is all zero, so there is no adder. Effect: raise = only larger jumps in fuel demand add extra fuel Evidence: ledger:E1139</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26704" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mg</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x377" flags="0x0">
    <title>Acceleration Fuel Adder - Fuel Fall That Clears It (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra fuel on acceleration: when the calculated fuel of a cylinder falls by more than this from one injection to the next (a negative value), the adder is cleared. Stock -3 mg. Dormant on the stock calibration: the adder gain curve is all zero, so there is no adder. Effect: more negative = the adder survives larger drops in fuel demand Evidence: ledger:E1139</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26706" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mg</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x378" flags="0x0">
    <title>Closed Loop Enable Coolant - Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once in closed loop, coolant may drop this far below the Closed Loop Enable Coolant curve before closed loop is dropped. Stock 3 C. Effect: raise = closed loop is kept through a larger coolant drop Evidence: ledger:E1006</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28E78" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x379" flags="0x0">
    <title>Hot-Restart Fuel - Minimum Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot-restart fuel gate: a latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, the Open Loop Hot-Restart Gain table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. This is the minimum coolant temperature. Stock 95 C. Effect: raise = hot-restart fuel needs a hotter engine and drops out soon...</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28EC2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x37A" flags="0x0">
    <title>Hot-Restart Fuel - Latch Intake Air</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot-restart fuel gate: a latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, the Open Loop Hot-Restart Gain table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. This is the latch intake air threshold. Stock 38 C. Effect: raise = hotter intake air needed to arm a hot restart Evidence: le...</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28ECC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x37B" flags="0x0">
    <title>Hot-Restart Fuel - Maximum Soak Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot-restart fuel gate: a latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, the Open Loop Hot-Restart Gain table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. This is the maximum engine-off soak time. Stock 3000 s (50 minutes). Effect: raise = longer stops still get hot-restart fuel E...</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28ECE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x37C" flags="0x0">
    <title>Hot-Restart Fuel - Minimum Soak Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot-restart fuel gate: a latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, the Open Loop Hot-Restart Gain table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. This is the minimum engine-off soak time. Stock 600 s (10 minutes). Effect: lower = shorter stops also get hot-restart fuel Ev...</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28ED0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x37D" flags="0x0">
    <title>O2 Sensor Ready - Resting Band High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor ready logic: a reading above this counts as sensor activity. Together with the band low value it marks the resting band a cold, inactive sensor sits in. Stock 550 mV. Effect: lower = a smaller rich swing counts as activity Evidence: ledger:E1005</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28F00" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x37E" flags="0x0">
    <title>O2 Sensor Ready - Resting Band Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor ready logic: a reading below this counts as sensor activity. Stock 350 mV. Effect: raise = a smaller lean swing counts as activity Evidence: ledger:E1005</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28F02" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x37F" flags="0x0">
    <title>O2 Sensor Ready - Coolant Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor ready logic: once the sensors are ready, coolant may drop this far below the O2 ready coolant curve before they are un-flagged. Stock 3 C. Effect: raise = ready is kept through a larger coolant drop Evidence: ledger:E1005</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28F4C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x380" flags="0x0">
    <title>O2 Sensor Ready - Inactive Time To Un-Flag</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor ready logic: a ready sensor is un-flagged after its reading has stayed inside the resting band for longer than this. Stock 10 s. Effect: raise = a sensor can sit in the resting band longer before it is un-flagged Evidence: ledger:E1005</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28F4E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x381" flags="0x0">
    <title>Idle A/C - Engage Pre-Ramp Torque Ratio Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: with the throttle open, idle air is pre-ramped before the A/C clutch engages only when A/C compressor torque is at or below this share of engine torque. Stock 0.45. Effect: raise = the pre-ramp also happens at lower engine torque Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x382" flags="0x0">
    <title>Idle A/C - Ramp Ready Share</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: share of the A/C idle air target that the ramp must reach before the clutch is released to engage. Stock 0.90. Effect: raise = the clutch waits for more of the idle air ramp Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x383" flags="0x0">
    <title>Idle A/C - Engage Pre-Ramp Torque Ratio Maximum, Converter Clutch On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: same torque ratio limit, used while the torque converter clutch is applying or applied. Stock 0.45. Effect: raise = the pre-ramp also happens at lower engine torque Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x384" flags="0x0">
    <title>Idle A/C - Throttle Closed Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: throttle at or below this counts as closed for the A/C idle air sequence. Stock 2.0 %. Effect: raise = a more open throttle still counts as closed Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x385" flags="0x0">
    <title>Idle A/C - Throttle Closed Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: the closed throttle flag clears only above the threshold plus this. Stock 0.7 %. Effect: raise = the closed throttle flag holds further into the throttle Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x386" flags="0x0">
    <title>Idle A/C - Release Adder Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: the idle air adder for A/C clutch release runs only with the throttle closed and below this speed. Stock 3 km/h. Effect: raise = the release adder also runs at higher speed Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x387" flags="0x0">
    <title>Idle A/C - Time Between Engage Sequences</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: minimum time after one engage sequence has ended before the next closed-throttle engage sequence. Stock 1 s. Effect: raise = repeated A/C engagements are spaced further apart Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x388" flags="0x0">
    <title>Idle Airflow Learn - Key-Off Save Step Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn: at key-off the saved value moves toward the value learned on this trip by at most this much. Stock 0.25 g/s per key cycle. Effect: raise = the saved learn follows each trip faster Evidence: ledger:E1106</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x389" flags="0x0">
    <title>Idle Airflow Learn - Restore Filter Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn: outside closed loop idle speed control the live learn value is pulled back toward the saved value only above this engine speed. Stock 0 rpm. Effect: raise = the restore filter needs more engine speed Evidence: ledger:E1106</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x38A" flags="0x0">
    <title>Idle Airflow Learn - Restore Filter Vehicle Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn: outside closed loop idle speed control the live learn value is pulled back toward the saved value only above this vehicle speed. Stock 255 km/h: the restore filter never runs. Effect: lower = the restore filter runs while driving above this speed Evidence: ledger:E1106</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29200" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x38B" flags="0x0">
    <title>Idle Airflow Integral - Step Down Throttle Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: the airflow integral may step down only while the throttle area above the idle area is below this. Stock 0.70 %. Effect: raise = the integral may also step down with the throttle a little further open Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29214" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x38C" flags="0x0">
    <title>Idle Air - Coolant Fallback Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air control: when the coolant reading is at or below this, the idle module uses the highest coolant temperature seen instead of the sensor reading. Stock -39 C (a failed-open sensor). Effect: raise = the fallback takes over at warmer readings Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x295CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x38D" flags="0x0">
    <title>Idle Key-Off - Throttle Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After key-off the idle throttle area is held at the key-off area value for this time, then idle control stops. Stock 2 s. Effect: raise = the key-off throttle position is held longer Evidence: ledger:E1106</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x296CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x38E" flags="0x0">
    <title>Idle Disturbance Latch - RPM Change per Sample</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: rpm change between two 12.5 ms samples above which the disturbance latch sets. Stock 8191.9 rpm: off. The disturbance latch: in closed loop idle speed control with the throttle closed, a sudden rpm change above a speed threshold puts the idle controller back in its moving mode for a time. Effect: lower = smaller rpm jumps set the latch Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29746" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x38F" flags="0x0">
    <title>Idle Disturbance Latch - Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: time the disturbance latch keeps the moving mode on. Stock 0 s. The disturbance latch: in closed loop idle speed control with the throttle closed, a sudden rpm change above a speed threshold puts the idle controller back in its moving mode for a time. Effect: raise = the moving mode is held longer after a disturbance Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29752" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x390" flags="0x0">
    <title>Idle Air - RPM Control Entry Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air control: idle speed control is entered only this long after the throttle follower has finished. Stock 0.05 s. Effect: raise = idle speed control takes over later after a throttle release Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29754" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x391" flags="0x0">
    <title>Decel Fuel Cut Idle Air - Fade Out Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air during decel fuel cut: once fuel cut is no longer active the extra idle air moves back toward 0 by this much every 12.5 ms. Stock 0.0098 g/s (0.78 g/s per second). Effect: raise = the fuel cut idle air is removed faster after fuel cut Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29E7E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x392" flags="0x30">
    <title>Cold Start High Idle - Idle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold start high idle: desired idle speed while the cold start high idle is active, in gear and in Park / Neutral. Stock 900 rpm for both. Effect: raise = higher idle after a very cold start Evidence: ledger:E1112</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>load state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="in gear" />
      <LABEL index="1" value="Park / Neutral" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A0D4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x393" flags="0x30">
    <title>Idle Cold Request - Until Coolant Reaches</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cold idle request stays active until the highest coolant temperature since start reaches this. Stock 0 C. Cold idle request: until the engine coolant has reached the limit at least once since start, desired idle is raised to at least the request speed (desired idle is the highest of all idle speed requests). Effect: raise = the cold idle request lasts until a warmer engine Evidence: ledger:E0436, ledger:E1508</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>1</indexcount>
      <units>field</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A5A0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="1" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x394" flags="0x0">
    <title>Desired Idle Requests - Hold Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Desired idle: an idle request whose condition has ended (A/C, cold start and others) stays held while the vehicle is slower than this, so idle speed does not drop while stopped. Stock 8 km/h. Effect: raise = finished idle requests are held up to a higher road speed Evidence: ledger:E1112</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A5A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x395" flags="0x0">
    <title>Per Cylinder Knock Retard Step Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Caps how much knock retard the computer can add to one cylinder in a single correction, before that amount is added onto the cylinder&#x27;s running knock retard. Stock is 5.0 degrees. It does not cap the total retard a cylinder can carry, only the size of each individual addition. Effect: raise = a knocking cylinder&#x27;s retard can jump by a larger amount in a single correction (faster buildup); lower = each correction adds less, so retard builds more slowly. Stock is 5.0 degrees per correction. Evidence: ledger:E0772, ledger:E0798</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2ABAC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x396" flags="0x0">
    <title>Burst Knock Retard - Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Burst knock retard sequence: a quick rise in cylinder airmass starts a burst of spark retard (sized by the burst retard curves and the learned multiplier). After the delay the retard is applied, held for the hold count, then removed in equal steps over the decay count. Counts are updates of the burst retard routine. This is the delay before the retard is applied. Stock 0 (applied at once). Effect: raise = the burst retard comes in later Evidence: ledger:E0870</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AD6C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x397" flags="0x0">
    <title>Burst Knock Retard Multiplier - Step Up</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Burst knock retard learned multiplier: two learned multipliers (1.0 = full burst retard) scale the burst knock retard. One event raises the active multiplier by the step up, another lowers it by the step down, and it is never allowed below the floor. Stock floor is 1.0, the top of the range, so on the stock calibration the multipliers stay at 1.0 and nothing is learned; lowering the floor lets burst retard learn down. This is the step up. Stock 0.05. Effect: raise = the multiplier climbs back toward 1.0 faster Evidence: ledger:E0869</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AD88" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x398" flags="0x0">
    <title>Burst Knock Retard Multiplier - Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Burst knock retard learned multiplier: two learned multipliers (1.0 = full burst retard) scale the burst knock retard. One event raises the active multiplier by the step up, another lowers it by the step down, and it is never allowed below the floor. Stock floor is 1.0, the top of the range, so on the stock calibration the multipliers stay at 1.0 and nothing is learned; lowering the floor lets burst retard learn down. This is the floor. Stock 1.0 (learning inert). Effect: lower = burst retard can learn down to this fraction Evidence: ledger:E0869</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AD8E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x399" flags="0x0">
    <title>Knock Learn Rate - MAP Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is one of the five weights (relative; only the ratios matter). Stock 1.0. Effect: raise = this curve counts for more in the average Evidence: ledger:E0193, ledger:E0871</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AF0C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x39A" flags="0x0">
    <title>Airmass Temperature Correction Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A gain constant in the airmass and barometric pressure correction chain, applied to the combined intake air and coolant temperature correction term. Stock is a gain of exactly 1.0, meaning the term currently passes through unscaled. Effect: Raising it above 1.0 would amplify the temperature correction term&#x27;s effect on the airmass calculation; lowering it below 1.0 would reduce that effect. Evidence: ledger:E0772, ledger:E0805</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2B17E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain (unitless)</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x39B" flags="0x0">
    <title>Airflow Model Learn Freeze - Release Throttle (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow model ratio learn: a freeze latch on the learn is released once throttle position is at or above this. Dormant on this software: the latch is only set in an engine state that no code produces, so this value never acts. Stock 0.5 %. Effect: no effect on this software Evidence: ledger:E0192, ledger:E0780, ledger:E0858, ledger:E1136</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2B1E0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x39C" flags="0x0">
    <title>VE Transient Mode - MAP Band Split</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow source switching: the PCM normally uses the MAF airflow and, during a manifold pressure transient, switches to the VE (speed density) airflow times a learned MAF to VE ratio. It switches over when MAP keeps moving by more than the MAP change threshold per update (two updates in a row), or when MAP moves more than that over two updates while the throttle area moves the same way by more than the area change threshold; it switches back once the MAP change over one, two and three updates is at or below the MAP change threshold. The high band thresholds apply at or above the MAP split or the RPM split. At or above this MAP...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x39D" flags="0x0">
    <title>VE Transient Mode - Window Exit Length (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of model updates a window must pass before the transient mode may end and the window starts again (stock 9). Part of the window check of the volumetric efficiency transient mode, which runs only when its throttle gate is open; on the stock calibration that gate is closed, so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0780, ledger:E0854, ledger:E1429</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4E0" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x39E" flags="0x30">
    <title>O2 Heater Cold Learn - Resistance Sample Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater cold-start resistance learn (after a long soak the PCM measures each heater cold and stores how far its resistance is from nominal): a cold resistance reading above this is not used as a learn sample. Stock 9.5 ohm upstream, 11.0 ohm downstream. Effect: raise = higher cold resistance readings are accepted as samples Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="upstream" />
      <LABEL index="1" value="downstream" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C7B6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>ohm</units>
      <decimalpl>3</decimalpl>
      <min>-64.000000</min>
      <max>63.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x39F" flags="0x30">
    <title>O2 Heater Cold Learn - Offset Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater cold-start resistance learn (after a long soak the PCM measures each heater cold and stores how far its resistance is from nominal): largest offset (expected minus measured resistance) that is accepted; beyond it nothing is learned and the heater code P0135 / P0141 sets. Stock 1.98 ohm upstream, 2.48 ohm downstream. Effect: raise = a heater further below nominal resistance is still accepted Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="upstream" />
      <LABEL index="1" value="downstream" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C7C2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>ohm</units>
      <decimalpl>3</decimalpl>
      <min>-64.000000</min>
      <max>63.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3A0" flags="0x30">
    <title>O2 Heater Cold Learn - Offset Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater cold-start resistance learn (after a long soak the PCM measures each heater cold and stores how far its resistance is from nominal): most negative offset (expected minus measured resistance) that is accepted; beyond it nothing is learned and the heater code P0135 / P0141 sets. Stock -3.24 ohm upstream, -4.20 ohm downstream. Effect: more negative = a heater further above nominal resistance is still accepted Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="upstream" />
      <LABEL index="1" value="downstream" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C7CE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>ohm</units>
      <decimalpl>3</decimalpl>
      <min>-64.000000</min>
      <max>63.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3A1" flags="0x30">
    <title>O2 Heater - Nominal Resistance at Reference Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor heater: nominal heater resistance at the reference temperature, used to predict the cold resistance in the learn and as the zero point of the heater temperature estimate. Stock 5.70 ohm upstream, 6.10 ohm downstream. Change only for a different sensor. Effect: raise = the heater is taken to be cooler at a given measured resistance Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="upstream" />
      <LABEL index="1" value="downstream" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C7DA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>ohm</units>
      <decimalpl>3</decimalpl>
      <min>-64.000000</min>
      <max>63.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3A2" flags="0x30">
    <title>O2 Heater - Wiring Voltage Drop</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater resistance measurement: voltage taken off the supply voltage, as lost in the wiring and driver, before heater resistance is computed. Stock 0 V. Effect: raise = a lower heater resistance is computed from the same readings Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="upstream" />
      <LABEL index="1" value="downstream" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C97E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>V</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3A3" flags="0x0">
    <title>O2 Heater - Measurement Current Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater resistance measurement: the running resistance and heater temperature are only updated when heater current in the measuring pulse is above this. Stock 0.20 A. Effect: raise = more heater current is needed for a resistance update Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C98A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>A</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3A4" flags="0x0">
    <title>O2 Heater Cold Learn - Sample Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater cold-start resistance learn (after a long soak the PCM measures each heater cold and stores how far its resistance is from nominal): filter on the cold resistance samples, as the fraction of the gap closed per sample. Stock 0.75. Effect: lower = the cold samples are smoothed more Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C98C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3A5" flags="0x0">
    <title>O2 Heater - Resistance Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater resistance measurement: filter on the running heater resistance, as the fraction of the gap closed per measurement. Stock 0.75. Effect: lower = the heater resistance (and temperature estimate) is smoothed more Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C98E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3A6" flags="0x0">
    <title>O2 Heater Cold Learn - Default Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater cold-start resistance learn (after a long soak the PCM measures each heater cold and stores how far its resistance is from nominal): offset assumed for every sensor until a learn has succeeded. Stock 0.56 ohm. Effect: raise = an unlearned heater is taken to be hotter at a given resistance Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C990" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>ohm</units>
    <decimalpl>3</decimalpl>
    <min>-64.000000</min>
    <max>63.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3A7" flags="0x0">
    <title>O2 Heater Cold Learn - Decision Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater cold-start resistance learn (after a long soak the PCM measures each heater cold and stores how far its resistance is from nominal): time into the first measuring pulse at which the learn is decided. Stock 0.0375 s. Effect: raise = the learn is decided later in the pulse Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C992" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3A8" flags="0x0">
    <title>O2 Heater Cold Learn - First Sample Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater cold-start resistance learn (after a long soak the PCM measures each heater cold and stores how far its resistance is from nominal): time into the first measuring pulse before cold resistance samples are taken. Stock 0.025 s. Effect: raise = sampling starts later in the pulse Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C994" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3A9" flags="0x0">
    <title>O2 Heater Cold Learn - Soak Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater cold-start resistance learn (after a long soak the PCM measures each heater cold and stores how far its resistance is from nominal): only runs after the engine has been off at least this long. Stock 36000 s (10 hours). Effect: lower = the learn also runs after a shorter soak Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C996" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3AA" flags="0x0">
    <title>O2 Heater - System Voltage Cut-Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor heater: both heaters are switched off while system voltage is above this. Stock 18 V. Effect: lower = the heaters are cut at a lower voltage Evidence: ledger:E1062</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C9D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3AB" flags="0x0">
    <title>Oil Life Reset - Press Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil life reset with the accelerator (key on, engine not turning): a press is counted when the throttle position signal rises above this. Stock 70 %. Effect: raise = the accelerator must be pressed further for a press to count Evidence: ledger:E1128</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C9EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3AC" flags="0x0">
    <title>Shift Lamp - Delay After a Downshift (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift lamp request (a data bus signal for a manual transmission upshift lamp): after a downshift the lamp is held off for this long. Stock 5 s. Dormant on this truck: the shift lamp request only runs on the manual transmission software path. Effect: raise = the lamp stays off longer after a downshift Evidence: ledger:E1143</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2CA84" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3AD" flags="0x0">
    <title>Shift Lamp - Maximum On Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift lamp request (a data bus signal for a manual transmission upshift lamp): longest time the lamp request stays on. Stock 3 s. Dormant on this truck: the shift lamp request only runs on the manual transmission software path. Effect: raise = the lamp may stay on longer Evidence: ledger:E1143</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2CA86" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3AE" flags="0x0">
    <title>Shift Lamp - Minimum Off Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift lamp request (a data bus signal for a manual transmission upshift lamp): shortest time before the lamp may come on again. Stock 1 s. Dormant on this truck: the shift lamp request only runs on the manual transmission software path. Effect: raise = longer pause between lamp requests Evidence: ledger:E1143</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2CA88" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3AF" flags="0x30">
    <title>Shift Lamp - Engine Speed Minimum by Gear, Cold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift lamp request (a data bus signal for a manual transmission upshift lamp): lowest engine speed for a lamp request in each gear while the engine is cold or just started. Stock 6500 rpm in every gear. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E1143</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="5th" />
      <LABEL index="5" value="6th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CAA0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3B0" flags="0x30">
    <title>Shift Lamp - Engine Speed Minimum by Gear, Warm</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift lamp request (a data bus signal for a manual transmission upshift lamp): lowest engine speed for a lamp request in each gear once the engine is warm. Stock 6500 rpm in every gear. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E1143</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="5th" />
      <LABEL index="5" value="6th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CAAC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3B1" flags="0x30">
    <title>Shift Lamp - MAP Minimum by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift lamp request (a data bus signal for a manual transmission upshift lamp): lowest manifold pressure for a lamp request in each gear. Stock 30 kPa, 40 kPa in the two highest gears. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E1143</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="5th" />
      <LABEL index="5" value="6th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CAB8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3B2" flags="0x30">
    <title>Shift Lamp - Pedal Minimum by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift lamp request (a data bus signal for a manual transmission upshift lamp): lowest pedal position (driver throttle request) for a lamp request in each gear. Stock 2 %. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E1143</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="5th" />
      <LABEL index="5" value="6th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CBA8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3B3" flags="0x0">
    <title>Tip-In Spark Advance Multiplier - Value With a Knock Sensor Code</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in spark advance, knock learned multiplier (the advance is multiplied by it; 1.0 = full advance). This value is used while a knock sensor code (P0325, P0326, P0327 or P0332) is failing. Stock 0.80. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: lower = less tip-in advance with a knock sensor fault Evidence: ledger:E1142</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2CDCA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3B4" flags="0x0">
    <title>Tip-In Spark Advance Multiplier - Step Up After a Clean Event</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in spark advance, knock learned multiplier (the advance is multiplied by it; 1.0 = full advance). Added after a tip-in advance event that passed without knock. Stock 0.005. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = the advance comes back faster after clean events Evidence: ledger:E1142</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2CDCC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3B5" flags="0x0">
    <title>Tip-In Spark Advance Multiplier - Step Down On Knock</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in spark advance, knock learned multiplier (the advance is multiplied by it; 1.0 = full advance). Subtracted when knock retard appears while the advance is active. Stock 0.010. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = knock during a tip-in removes the advance faster Evidence: ledger:E1142</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2CDCE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3B6" flags="0x30">
    <title>EGR Spark Correction - Filter Rising / Falling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark added from the EGR spark correction table is scaled by the cam-phase factor (Cam-Phase Factor vs Cam Angle and RPM) divided by a normaliser (stock 0.24, the factor table&#x27;s largest value), so the table applies in full at 24 degrees of cam and in proportion below it. These two values are the filter speeds of that spark: the first while it rises (stock 0.5 of the difference per update), the second while it falls (stock 1.0, at once). Effect: raise = the spark correction follows changes faster Evidence: ledger:E0436, ledger:E0883</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>direction</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="rising" />
      <LABEL index="1" value="falling" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2DC3A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3B7" flags="0x0">
    <title>Starter - Crank Request Debounce Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The crank request from the ignition switch must be present for this long, in park or neutral, before the PCM engages the starter relay. Stock 0.05 s. Effect: raise = the key must be held in crank longer before the starter engages Evidence: ledger:E1024</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x3028E" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3B8" flags="0x0">
    <title>Starter - System Voltage OK Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter control: time the system voltage must have been above its minimum (6 V) before the starter may engage. Stock 0 s: no wait. Effect: raise = the starter engages only after the voltage has been up for that long Evidence: ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30294" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3B9" flags="0x0">
    <title>Starter - Minimum On Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once engaged, the starter relay stays on for at least this long before the key-released and crank time limit checks can turn it off (leaving park / neutral or the engine starting still turn it off at once). Stock 0.2 s. Effect: raise = the starter stays engaged longer after a brief key turn Evidence: ledger:E1024</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x30296" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3BA" flags="0x0">
    <title>Starter - Maximum Crank Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM turns the starter relay off after this much continuous cranking, and does not re-engage it until the key is released. Stock 15 s. Effect: raise = the starter may crank longer in one attempt Evidence: ledger:E1024</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x302A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3BB" flags="0x0">
    <title>Starter Low-Voltage Hold - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter low-voltage hold: 1 lets the PCM keep the starter engaged through a voltage collapse below 4 V while cranking; 0 turns the feature off. Stock 1. Effect: 0 = the starter follows the key signal only Evidence: ledger:E1025</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x302A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3BC" flags="0x0">
    <title>Starter Low-Voltage Hold - Run Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter low-voltage hold: the hold is cancelled once engine run time is longer than this. Stock 1.0 s. Effect: raise = the hold can persist longer after the engine fires Evidence: ledger:E1025</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x302B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3BD" flags="0x0">
    <title>Starter Low-Voltage Hold - Cancel Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter low-voltage hold: the hold is cancelled when system voltage stays above 4 V but below this for the cancel time. Stock 6.0 V. Effect: raise = a higher sustained cranking voltage still cancels the hold Evidence: ledger:E1025</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x302B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3BE" flags="0x0">
    <title>Starter Low-Voltage Hold - Cancel Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter low-voltage hold: how long system voltage must stay between 4 V and the cancel voltage to cancel the hold. Stock 0.5 s. Effect: raise = the low voltage must last longer to cancel the hold Evidence: ledger:E1025</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x302B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3BF" flags="0x0">
    <title>Starter Low-Voltage Hold - Fuel Level Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter low-voltage hold: the hold is not used when the fuel level is at or below this (a held mode setting can override this). Stock 2 %. Effect: raise = the hold is dropped at higher fuel levels Evidence: ledger:E1036</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x302BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3C0" flags="0x0">
    <title>Torque Model - Engine Torque Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque model: share of each new value taken into the filtered engine torque values every 25 ms. Stock 0.25; 1.0 = no filtering. Effect: raise = the modelled engine torque follows changes faster Evidence: ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x303CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3C1" flags="0x0">
    <title>Torque Reduction Cylinder Cut - Cylinders Added Back on a First Gear Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque reduction with cylinder cut: cylinders added back to the fuelled count for a short time when traction control is reducing torque during a shift out of first gear. Stock 2. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = more cylinders are given back for that shift Evidence: ledger:E1133</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x313CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cylinders</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3C2" flags="0x0">
    <title>Torque Reduction Cylinder Cut - Shift Add-Back Time Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque reduction with cylinder cut: longest time the shift add-back stays on. Stock 0.5 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = the add-back may last longer Evidence: ledger:E1133</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x313CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3C3" flags="0x0">
    <title>Torque Reduction Cylinder Cut - Shift Add-Back Speed Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque reduction with cylinder cut: the shift add-back starts when the transmission input to output speed ratio falls below this during the shift. Stock 1.5. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = the add-back starts earlier in the shift Evidence: ledger:E1133</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x313CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3C4" flags="0x0">
    <title>Torque Reduction Spark Retard - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque reduction: spark retard is only requested once the engine has run longer than this. Stock 5 s. Effect: raise = no torque reduction spark retard for longer after a start Evidence: ledger:E1130</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x31960" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3C5" flags="0x0">
    <title>Torque Reduction Spark Retard - Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque reduction: spark retard is only requested above this engine speed. Stock 600 rpm. Effect: raise = no torque reduction spark retard at low engine speed Evidence: ledger:E1130</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x31962" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3C6" flags="0x0">
    <title>Closed Throttle Flag - Set Below Commanded Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed throttle flag (used by the A/C compressor control to hold the compressor off just after the throttle closes): the flag sets when the commanded throttle area above the idle area is at or below this, and the measured throttle is also at or below its own limit. The flag clears again when the commanded value rises above this plus the release hysteresis. Stock 0.1 %. Effect: raise = the throttle counts as closed at a larger commanded opening Evidence: ledger:E1137</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31A40" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3C7" flags="0x30">
    <title>Knock Detection - Level Filter Multipliers During Knock</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: in a knock window where the cylinder knocked, its reference level filter is multiplied by the first value and its noise level filter by the second, so that knock itself is kept out of the levels. Stock 1.0 for the reference level (no change) and 0.01 for the noise level. Effect: lower = a knocking sample moves that level less Evidence: ledger:E1138</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>level</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="reference level" />
      <LABEL index="1" value="noise level" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31D2C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3C8" flags="0x0">
    <title>Knock Threshold Learn - Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock threshold learn: share of the gap to its target that the learned threshold factor of a cylinder closes after each knock window. Stock 0.0025. Effect: raise = the learned factor moves faster Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31D44" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3C9" flags="0x0">
    <title>Knock Threshold Learn - Factor Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock threshold learn: lowest value of the learned factor. The knock threshold of a cylinder is its reference level plus this factor times the threshold table value, so a lower factor makes knock detection more sensitive. Stock 0.70. Effect: raise = the learn can lower the knock threshold less, so knock detection stays less sensitive Evidence: ledger:E1131, ledger:E1138</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31D46" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3CA" flags="0x0">
    <title>Knock Threshold Learn - Factor Maximum and Default</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock threshold learn: highest value of the learned factor, and the value every cylinder starts from when the stored factors are lost. Stock 1.00. Effect: raise = the learn may raise the knock threshold above the table value Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31D48" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3CB" flags="0x0">
    <title>Knock Threshold Learn - Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock threshold learn: the learned factor is only updated above this engine speed. Stock 1500 rpm. Effect: raise = no learning at lower engine speed Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31D4A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3CC" flags="0x0">
    <title>Knock Threshold Learn - Airmass Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock threshold learn: the learned factor is only updated above this cylinder airmass. Stock 0.32 g per cylinder. Effect: raise = no learning at lighter load Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31D4C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/cyl</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.095937</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3CD" flags="0x0">
    <title>Crank Variation Learn - Attempt Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn: a learn request is refused once the number of learn attempts is above this. Stock 255 (no limit). Effect: lower = the learn can only be attempted this many times Evidence: ledger:E1081</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328B2" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>attempts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3CE" flags="0x0">
    <title>Crank Variation Learn - Coolant Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn (the service procedure that clears P0315): the learn is refused while coolant is below this. Stock 65 degC. Effect: raise = the learn needs a warmer engine Evidence: ledger:E1040</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3CF" flags="0x0">
    <title>Crank Variation Learn - RPM Rise Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn (the service procedure that clears P0315): sampling is abandoned if engine speed rises by more than this from one sample pass to the next. Stock 50 rpm. Effect: raise = a larger rpm rise is tolerated while sampling Evidence: ledger:E1040</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3D0" flags="0x0">
    <title>Crank Variation Learn - Sampling RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn (the service procedure that clears P0315): samples are taken only while engine speed is above this; at or below it sampling ends. Stock 1500 rpm. Effect: raise = sampling ends at a higher engine speed Evidence: ledger:E1040</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3D1" flags="0x0">
    <title>Crank Variation Learn - Sampling RPM Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn (the service procedure that clears P0315): once armed, samples are taken only while engine speed is at or below this. Stock 3800 rpm. Effect: raise = sampling starts at a higher engine speed Evidence: ledger:E1040</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3D2" flags="0x0">
    <title>Catalyst Monitor - Stopped Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: vehicle speed at or below this counts as stopped. Stock 7 km/h. Effect: raise = the test also treats a slow roll as stopped Evidence: ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328E0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3D3" flags="0x0">
    <title>Catalyst Monitor Enable - Catalyst Temperature Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): the test is armed only while the modelled catalyst temperature is at or below this. Stock 700 C. Effect: lower = the test is skipped at lower catalyst temperatures Evidence: ledger:E0437, ledger:E0852, ledger:E0967, ledger:E1188</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>1023.984375</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/64"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3D4" flags="0x0">
    <title>Catalyst Monitor - Second Step Downstream Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: if the downstream O2 sensor has not switched within this long of the second fuel step starting, the catalyst is given the maximum storage time. Stock 6.0 s. Effect: lower = a slow downstream switch is scored as maximum storage sooner Evidence: ledger:E1000</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32918" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3D5" flags="0x0">
    <title>Catalyst Monitor - Maximum Storage Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: storage time recorded when the downstream O2 sensor does not switch within its time limits. Stock 7.0 s. Effect: raise = a catalyst that outlasts the test is scored with a longer storage time Evidence: ledger:E1000</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3291A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3D6" flags="0x0">
    <title>Catalyst Monitor - Trim Averaging Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): before the fuel steps the short term fuel trim is averaged over whole O2 sensor switch cycles for at least this long. Stock 4 s. Effect: raise = the trim is averaged longer before the fuel steps Evidence: ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3291C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3D7" flags="0x0">
    <title>Catalyst Monitor - Trim Averaging Time Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): if the trim average is not complete after this long the test is abandoned. Stock 10 s. Effect: raise = the test waits longer for a usable trim average Evidence: ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3291E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3D8" flags="0x30">
    <title>Catalyst Monitor Enable - Average Short Term Trim Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): the short term fuel trim averaged over the trim sampling time must be at or above this for the test to go on (one value per catalyst; this truck uses the first). Stock 0.94. Effect: raise = a leaner average trim stops the test Evidence: ledger:E1082, ledger:E1188</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>catalyst</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x32924" mmedelementsizebits="32" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>131071.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3D9" flags="0x30">
    <title>Catalyst Monitor Enable - Average Short Term Trim Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): the short term fuel trim averaged over the trim sampling time must be at or below this for the test to go on (one value per catalyst; this truck uses the first). Stock 1.06. Effect: lower = a richer average trim stops the test Evidence: ledger:E0437, ledger:E1082, ledger:E1188</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>catalyst</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3292C" mmedelementsizebits="32" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>131071.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3DA" flags="0x0">
    <title>Catalyst Monitor - Purge Ramp Out Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): rate at which canister purge is ramped to zero when a test is armed. Stock 99 % per second. Effect: lower = purge is shut off more gradually before a test Evidence: ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32944" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% per s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>64997.613000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*0.9918"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3DB" flags="0x0">
    <title>Catalyst Monitor - Purge Ramp In Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): rate at which canister purge is brought back after a test. Stock 397 % per second (back within about a quarter of a second). Effect: lower = purge returns more gradually after a test Evidence: ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32946" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% per s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>64997.613000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*0.9918"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3DC" flags="0x0">
    <title>Catalyst Monitor Enable - Short Term Trim Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): the short term fuel trim must stay at or above this during the test, otherwise the attempt is dropped (1.0 = no correction). Stock 0.88. Effect: raise = the test is dropped with less lean correction Evidence: ledger:E1082, ledger:E1188</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32948" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3DD" flags="0x0">
    <title>Catalyst Monitor Enable - Short Term Trim Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): the short term fuel trim must stay at or below this during the test, otherwise the attempt is dropped (1.0 = no correction). Stock 1.12. Effect: lower = the test is dropped with less rich correction Evidence: ledger:E1082, ledger:E1188</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3294A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3DE" flags="0x0">
    <title>Catalyst Monitor Enable - Short Term Trim Change Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): the short term fuel trim may move at most this far from its value at the start of the test, otherwise the attempt is dropped. Stock 0.12. Effect: lower = the test is dropped on smaller trim movement Evidence: ledger:E1082, ledger:E1188</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3294C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3DF" flags="0x30">
    <title>Catalyst Monitor - Fuel Step Airflow Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow points of the two catalyst monitor fuel step curves. Stock 3 to 12 g/s. The curves that use it are spread over these points, so moving them re-spaces those curves; keep the point count and keep the points rising. Effect: moving a point shifts where the fuel step curves change Evidence: ledger:E1002</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x32952" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E0" flags="0x30">
    <title>Catalyst Monitor - First Step Upstream Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: the test is thrown away if the upstream O2 sensor takes longer than this to respond to the first fuel step. Stock 2.0 s. Effect: raise = a slower upstream response is still accepted Evidence: ledger:E1000</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x329B8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E1" flags="0x30">
    <title>Catalyst Monitor - Second Step Upstream Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: the test is thrown away if the upstream O2 sensor takes longer than this to respond to the second fuel step. Stock 2.0 s. Effect: raise = a slower upstream response is still accepted Evidence: ledger:E1000</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x329BC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E2" flags="0x30">
    <title>Catalyst Monitor - Fast Pass Margin</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: while every test so far has beaten the reference by more than this margin, the monitor counts as having enough tests to pass at once. The value is the shortfall limit, so it is negative. Stock -0.6 s (storage time more than 0.6 s above the reference). Effect: more negative = a larger margin is needed for the fast pass Evidence: ledger:E1021</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>bank</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x329C8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>-204.800000</min>
      <max>204.793750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E3" flags="0x30">
    <title>Catalyst Monitor - Fail Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: P0420 sets when the filtered shortfall of storage time below the reference is greater than this. Stock 0.28 s. Effect: raise = the catalyst must fall further short before the code sets Evidence: ledger:E1021</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>bank</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x329D8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3E4" flags="0x0">
    <title>Catalyst Monitor - Tests To Pass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: the monitor reports a pass once this many tests have gone into the filtered result without it exceeding the fail limit. Stock 6. Effect: raise = more tests are needed before a pass is reported Evidence: ledger:E1021</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x329DC" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>tests</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3E5" flags="0x0">
    <title>Catalyst Monitor - Result Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: share of each new test result that goes into the filtered result (the rest is the previous filtered value). Stock 0.10. Effect: raise = the filtered result follows new tests faster Evidence: ledger:E1021</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x329E0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3E6" flags="0x0">
    <title>Catalyst Monitor - First Fuel Step Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: the first fuel step is held for this long before the second step starts. Stock 6.0 s. Effect: raise = the first fuel step lasts longer Evidence: ledger:E1000</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x329E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3E7" flags="0x0">
    <title>Catalyst Monitor - End Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: after the fuel steps finish, the monitor waits this long before closing the test. Stock 1.0 s. Effect: raise = longer wait at the end of the test Evidence: ledger:E1000</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x329E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3E8" flags="0x0">
    <title>Catalyst Monitor - Rich Step Upstream Switch Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: when the test starts with its rich step (stock), the upstream O2 sensor counts as switched once it reads at or above this. Stock 600 mV. Effect: lower = the upstream sensor counts as switched at a lower reading Evidence: ledger:E1000</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x329E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3E9" flags="0x0">
    <title>P0125 / P0128 Check - Airflow Counted Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: airflow below this is not counted when the checks add up the air the engine has drawn since start. Stock 7 g/s. Effect: raise = low airflow (idling) no longer counts toward the required air mass Evidence: ledger:E0776, ledger:E0805, ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33728" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3EA" flags="0x0">
    <title>P0125 / P0128 Fail - Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: the code sets after the failing condition (required air drawn, coolant still below the target) has been seen on this many one second passes. Stock 30. Effect: raise = the failing condition must last longer before the code sets Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33736" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3EB" flags="0x0">
    <title>Coolant Temperature Rise Rate Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The maximum amount the reported, filtered engine coolant temperature is allowed to climb toward the raw sensor reading on each update. Stock is about 1.2 degrees Celsius per update. Effect: Raising it lets the reported coolant temperature rise faster toward the raw sensor reading each update; lowering it slows how quickly it can rise. Evidence: ledger:E0776, ledger:E0805</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x337B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3EC" flags="0x30">
    <title>Exhaust Temperature Model - Base Temperature (Hot Channel)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): each channel&#x27;s target is a base temperature plus an engine speed term and an airflow term, capped at 1000 C. This base is used while the channel is at or above the base switch temperature. Stock 240 C. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = a hotter modelled temperature at every operating point once the channel is hot Evidence: ledger:E0769, ledger:E0852, ledger:E0968, ledger:E1188, ledger:E1192, ledger:E1558</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33800" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1023.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3ED" flags="0x30">
    <title>Exhaust Temperature Model - Base Temperature (Cool Channel)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): each channel&#x27;s target is a base temperature plus an engine speed term and an airflow term. This base is used while the channel is below the base switch temperature. Stock 180 C. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = the modelled temperature climbs faster from cool Evidence: ledger:E0769, ledger:E0852, ledger:E0968, ledger:E1188, ledger:E1192, ledger:E1558</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33810" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1023.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3EE" flags="0x30">
    <title>Exhaust Temperature Model - Base Switch Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): at or above this modelled temperature a channel uses the hot base temperature, below it the cool base temperature. Stock 488 C. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: lower = the hot base applies from a lower modelled temperature Evidence: ledger:E0769, ledger:E0852, ledger:E0968, ledger:E1188, ledger:E1192, ledger:E1558</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33820" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1023.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3EF" flags="0x30">
    <title>Exhaust Temperature Model - Cold Engine Target</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): while the coolant is below the model&#x27;s coolant gate (stock 69 C) each channel moves toward this fixed temperature instead of the speed and airflow target. Stock 300 C. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = a cold engine is modelled with a hotter exhaust Evidence: ledger:E0769, ledger:E0852, ledger:E0968, ledger:E1188, ledger:E1192, ledger:E1558</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33830" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1023.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3F0" flags="0x30">
    <title>Exhaust Temperature Model - Filter Rate, Falling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): fraction of the gap between the model channel&#x27;s target and its present value closed at each model update while the target is below the present value (stock about 1.8 %, 1180 of 65536 = 1.8 % falling, 3277 = 5.0 % rising). Larger = the modelled temperature follows its target faster. Channel 3 is the catalyst channel used by the catalyst monitor readiness count. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = the model follows its target faster Evidence: l...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33840" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3F1" flags="0x30">
    <title>Exhaust Temperature Model - Filter Rate, Rising</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): fraction of the gap between the model channel&#x27;s target and its present value closed at each model update while the target is at or above the present value (stock about 5.0 %, 1180 of 65536 = 1.8 % falling, 3277 = 5.0 % rising). Larger = the modelled temperature follows its target faster. Channel 3 is the catalyst channel used by the catalyst monitor readiness count. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = the model follows its target faster Evide...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33850" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3F2" flags="0x30">
    <title>Exhaust Temperature Model - Airflow Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): the target rises this much per g/s of airflow (airflow above the airflow input ceiling counts as the ceiling). Stock 2.26 C per g/s, 113 C at the stock 50 g/s ceiling. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = a hotter modelled temperature at higher airflow Evidence: ledger:E0588, ledger:E0769, ledger:E0852, ledger:E1188, ledger:E1192, ledger:E1558</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33860" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC per g/s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3F3" flags="0x30">
    <title>Exhaust Temperature Model - Engine Speed Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): the target rises this much per rpm of engine speed (speed above the engine speed input ceiling counts as the ceiling). Stock 0.205 C per rpm, 820 C at the stock 4000 rpm ceiling. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = a hotter modelled temperature at higher engine speed Evidence: ledger:E0588, ledger:E0769, ledger:E0852, ledger:E1188, ledger:E1192, ledger:E1558</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33870" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC per rpm</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3F4" flags="0x0">
    <title>EVAP Engine-Off Test - Vent Open Abort Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test, first step with the vent open: if the average tank reading is below this the test is abandoned. Stock -0.5 inH2O (0.5 inH2O of pressure). Tank readings are vacuum: positive is vacuum, negative is pressure. Effect: raise (toward 0) = less pressure with the vent open abandons the test Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D08" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-209715.200000</min>
    <max>209715.199902</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10240"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3F5" flags="0x0">
    <title>EVAP Engine-Off Test - Vent Open Derate Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test, first step with the vent open: if the average tank reading is below this (but not below the abort level) the pressure peak is scaled by the derate factor. Stock -0.45 inH2O. Tank readings are vacuum: positive is vacuum, negative is pressure. Effect: raise (toward 0) = the derate applies with less vent-open pressure Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D0C" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-209715.200000</min>
    <max>209715.199902</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10240"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3F6" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Phase Flat Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the pressure phase ends when the tank reading has stayed inside the flat band for this long. Stock 600 s. Effect: raise = the test waits longer for pressure to build Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D14" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3F7" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Phase Early Vacuum Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: vacuum at or above the early vacuum level for this long during the pressure phase starts the vacuum phase at once. Stock 0.1 s. Effect: raise = early vacuum must last longer before the vacuum phase starts Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D16" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3F8" flags="0x0">
    <title>EVAP Engine-Off Test - Vacuum Phase Flat Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the vacuum phase ends when the tank reading has stayed inside the flat band for this long. Stock 1000 s. Effect: raise = the test waits longer for vacuum to build Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D18" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3F9" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Phase Peak Fall-Back</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the pressure phase ends once the tank reading has come back by this much from its pressure peak. Stock -0.25 inH2O (the value is peak minus current reading, so it is negative). Effect: more negative = a larger fall-back from the peak is needed Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D2A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3FA" flags="0x0">
    <title>EVAP Engine-Off Test - Vacuum Phase Peak Fall-Back</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the vacuum phase ends once the tank reading has dropped by this much from its vacuum peak. Stock 0.25 inH2O. Effect: raise = a larger fall-back from the vacuum peak is needed Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D2C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3FB" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Phase Early Vacuum Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: a tank reading at or above this during the pressure phase (vacuum instead of pressure) starts the vacuum phase without venting. Stock 0.20 inH2O. Tank readings are vacuum: positive is vacuum, negative is pressure. Effect: raise = more vacuum is needed to skip straight to the vacuum phase Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D2E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3FC" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Phase Flat Band Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: lower edge of the band in which the pressure phase counts the tank as not building pressure. Stock -0.31 inH2O. Tank readings are vacuum: positive is vacuum, negative is pressure. Effect: more negative = more pressure still counts as flat Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D30" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3FD" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Phase Flat Band High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: upper edge of the band in which the pressure phase counts the tank as not building pressure. Stock 0.31 inH2O. Tank readings are vacuum: positive is vacuum, negative is pressure. Effect: raise = more vacuum still counts as flat Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D32" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3FE" flags="0x0">
    <title>EVAP Engine-Off Test - Vacuum Phase Flat Band Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: lower edge of the band in which the vacuum phase counts the tank as not building vacuum. Stock -0.30 inH2O. Tank readings are vacuum: positive is vacuum, negative is pressure. Effect: more negative = more pressure still counts as flat Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D36" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3FF" flags="0x0">
    <title>EVAP Engine-Off Test - Vacuum Phase Flat Band High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: upper edge of the band in which the vacuum phase counts the tank as not building vacuum; also the smallest vacuum peak that the peak fall-back check accepts. Stock 0.30 inH2O. Effect: raise = more vacuum still counts as flat Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D38" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x400" flags="0x0">
    <title>EVAP Engine-Off Test - Vacuum Target Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: smallest vacuum target the vacuum phase may use (the target is otherwise the reference less the pressure already reached). Stock 0 inH2O. Effect: raise = the vacuum phase always needs at least this much vacuum to finish early Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D3A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x401" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Peak Derate Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: factor applied to the stored pressure peak when the vent-open reading was below the derate level. Stock 0.50. Effect: lower = the pressure peak counts for less after a pressurised vent-open step Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D3C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x402" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Phase Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: longest time the pressure phase may last before the test moves on. Stock 2499 s. Effect: raise = the pressure phase may last longer Evidence: ledger:E0776, ledger:E0805, ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D46" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x403" flags="0x0">
    <title>EVAP Engine-Off Test - Refuelling Confirm Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: when the test is disturbed and the fuel level has stayed changed for longer than this, the disturbance is put down to refuelling and not counted against the sensors. Stock 30 s. Effect: raise = the fuel level must stay changed longer to count as refuelling Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D4A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x404" flags="0x0">
    <title>EVAP Engine-Off Test - Disturbance Wait Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: how long a disturbed test waits before the disturbance is counted as a bad sample against the tank pressure sensor (P0454), the fuel level sensor (P0464) or the sensor zero (P0451). Stock 600 s. Effect: raise = a disturbance is counted later Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D4C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x405" flags="0x0">
    <title>EVAP Engine-Off Test - Vent Time Between Phases</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: how long the vent is held open between the pressure phase and the vacuum phase. Stock 45 s. Effect: raise = the tank is vented longer before the vacuum phase Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D4E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x406" flags="0x0">
    <title>EVAP Engine-Off Test - Total Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: once the engine has been off this long the test stops waiting and evaluates what it has. Stock 2500 s. Effect: raise = the test may run longer after shut-off Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D50" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x407" flags="0x0">
    <title>EVAP Engine-Off Test - Re-Vent Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: how long the vent is held open for a re-vent in the vacuum phase. Stock 300 s. Effect: raise = each re-vent lasts longer Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D52" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x408" flags="0x0">
    <title>EVAP Engine-Off Test - Zero Shift Limit, Upward</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): sensor voltage above the stored zero by this much is rated 1.0 and stops the test; smaller shifts are rated in proportion. Used from the second zero check of a test on. Stock 0.20 V. Effect: raise = a larger upward zero shift is tolerated Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D54" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x409" flags="0x0">
    <title>EVAP Engine-Off Test - Zero Shift Limit, Downward</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): the same for a sensor voltage below the stored zero. Used from the second zero check of a test on. Stock 0.20 V. Effect: raise = a larger downward zero shift is tolerated Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D56" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x40A" flags="0x0">
    <title>EVAP Engine-Off Test - Zero Shift Limit, Upward (first check)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): upward limit used for the first zero check of a test. Stock 0.20 V. Effect: raise = a larger upward zero shift is tolerated Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D58" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x40B" flags="0x0">
    <title>EVAP Engine-Off Test - Zero Shift Limit, Downward (first check)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): downward limit used for the first zero check of a test. Stock 0.20 V. Effect: raise = a larger downward zero shift is tolerated Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D5A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x40C" flags="0x0">
    <title>Ambient Air Temp Estimate - Flush Requirement Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Whenever the airflow or speed gate is not met, the flush requirement grows by one second each second up to this ceiling, and a larger requirement is cut down to it (stock 40 s). The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it down, and until it reaches zero the estimate can only fall toward the intake air temperature. Effect: raise = more flushing is needed again after slowing down Evidence: ledger:E0385, ledger:E1184, l...</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x342CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>204.796875</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/320"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x40D" flags="0x0">
    <title>EVAP Engine-Off Test - Tank Pressure Sensor Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: tank pressure sensor slope used by this test, in inH2O of tank vacuum per volt away from the sensor zero. Stock 5.0. Change only for a different sensor. Effect: raise = the same sensor voltage change reads as more pressure Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>inH2O per V</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x40E" flags="0x0">
    <title>EVAP Engine-Off Test - Unfinished Attempt Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: after this many enabled tests that did not finish, the time since the last test is restarted anyway. Stock 2. Effect: raise = more unfinished attempts are made before the wait starts again Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x40F" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Trip Distance Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs after a trip of at least this distance. Stock 5 km. Effect: raise = a longer trip is needed before the test runs Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345C2" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1048575.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x410" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Vehicle Distance Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs once the vehicle has covered this distance since new (the counter stops at 6436 km). Stock 16 km. Effect: raise = the test stays off for longer on a new vehicle Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345C6" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1048575.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x411" flags="0x0">
    <title>EVAP Engine-Off Test - Fuel Level Used on Sensor Fault</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: fuel level assumed while the fuel level sensor is faulted. Stock 50 %. Effect: changes the reference the test uses with a faulted sensor Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x412" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Fuel Level Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs with the fuel level at or below this. Stock 85 %. Effect: raise = the test also runs with a fuller tank Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x413" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Fuel Level Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs with the fuel level at or above this. Stock 15 %. Effect: lower = the test also runs with an emptier tank Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x414" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Ambient Temperature Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs with ambient air temperature at or below this. Stock 32 degC. Effect: raise = the test also runs on hotter days Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345D4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x415" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Ambient Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs with ambient air temperature at or above this. Stock 2 degC. Effect: lower = the test also runs in colder weather Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345D6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x416" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Coolant Temperature at Shut-Off Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs when coolant temperature at engine shut-off was at or above this. Stock 70 degC. Effect: lower = the test also runs after a cooler shut-off Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345DA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x417" flags="0x0">
    <title>EVAP Engine-Off Test - Fuel Vapour Temperature Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: how fast its filtered fuel vapour temperature follows the sensor, as the fraction of the gap closed per update. Stock 0.10. Effect: lower = the temperature is smoothed more Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345DC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x418" flags="0x0">
    <title>EVAP Engine-Off Test - Tank Pressure Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: how fast the tank reading its phases use follows the sensor, as the fraction of the gap closed per update. Stock 0.0625. Effect: lower = the tank reading is smoothed more (slower to react) Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345DE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x419" flags="0x0">
    <title>EVAP Engine-Off Test - Disturbance Check Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: filter on the tank reading used by the disturbance check, as the fraction of the gap closed per update. Stock 0.05. Effect: lower = the disturbance check sees a smoother tank reading Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345E0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x41A" flags="0x0">
    <title>EVAP Engine-Off Test - Disturbance Check Sample Jump Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the disturbance check ignores a pass in which the unfiltered tank reading jumped by this much or more from the previous sample. Stock 1.0 inH2O. Effect: raise = larger sample-to-sample jumps are still judged Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x41B" flags="0x0">
    <title>EVAP Engine-Off Test - Disturbance Pressure Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: a filtered tank reading at or below this with the vent closed flags a disturbance. Stock -4.0 inH2O (4 inH2O of pressure). Tank readings are vacuum: positive is vacuum, negative is pressure. Effect: more negative = more tank pressure is tolerated before a disturbance is flagged Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x41C" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs after the engine has run at least this long on the trip. Stock 600 s. Effect: raise = a longer run is needed before the test runs Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x41D" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Time Since Last Test, After a Good Result</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: engine run time plus soak time that must pass since the last test when that test gave a good result. Stock 17 h. Effect: raise = the test runs less often after a good result Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>h</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x41E" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Time Since Last Test</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: engine run time plus soak time that must pass since the last test in the other cases. Stock 10 h. Effect: raise = the test runs less often Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>h</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x41F" flags="0x0">
    <title>EVAP Engine-Off Test - Start Delay After Shut-Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test takes over this long after the engine stops. Stock 6 s. Effect: raise = the test starts later after shut-off Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x420" flags="0x0">
    <title>EVAP Engine-Off Test - Trip Distance Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the trip distance it requires only counts while vehicle speed is at or above this. Stock 1.6 km/h. Effect: raise = slow driving no longer counts toward the trip distance Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x421" flags="0x0">
    <title>EVAP Engine-Off Test - Disturbance Check Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the disturbance check compares the filtered tank reading with a snapshot that is refreshed this often. Stock 1.0 s. Effect: raise = the check looks at pressure changes over a longer interval Evidence: ledger:E0776, ledger:E0805, ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x346CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x422" flags="0x0">
    <title>EVAP Engine-Off Service Test - Ambient Temperature Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP service test (the scan tool started version of the leak test) only runs with ambient air temperature at or below this while the PCM&#x27;s ambient estimate is not yet valid. Stock 40 degC. Effect: raise = the service test also runs when hotter Evidence: ledger:E1055</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x346F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x423" flags="0x0">
    <title>EVAP Engine-Off Service Test - Ambient Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP service test (the scan tool started version of the leak test) only runs with ambient air temperature at or above this while the PCM&#x27;s ambient estimate is not yet valid. Stock 2 degC. Effect: lower = the service test also runs when colder Evidence: ledger:E1055</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x346F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x424" flags="0x0">
    <title>EVAP Engine-Off Service Test - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP service test (the scan tool started version of the leak test) only runs after the engine has run at least this long (the scan tool shows the time still to go). Stock 1200 s. Effect: raise = a longer run is needed before the service test Evidence: ledger:E1055</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x346F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x425" flags="0x0">
    <title>EVAP Engine-Off Service Test - Trip Distance Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP service test (the scan tool started version of the leak test) only runs after a trip of at least this distance (the scan tool shows the distance still to go). Stock 16.1 km (10 miles). Effect: raise = a longer drive is needed before the service test Evidence: ledger:E1055</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x346FA" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1048575.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x426" flags="0x0">
    <title>EVAP Engine-Off Test - Vent Command Mismatch Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the test is ended when the vent valve command has differed from what the test asked for, for this long. Stock 0.5 s. Effect: raise = a longer mismatch is tolerated before the test ends Evidence: ledger:E1055</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x346FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x427" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Barometric Pressure Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs with barometric pressure at or above this. Stock 74 kPa. Effect: raise = the test stops running at lower altitude Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34700" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x428" flags="0x0">
    <title>EVAP Engine-Off Test - Fuel Level Change Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: a fuel level that differs from the level at the start of the test by more than this disturbs the test (and, if it lasts, counts as refuelling). Stock 20 %. Effect: raise = a larger fuel level change is tolerated during the test Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34706" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x429" flags="0x30">
    <title>P0134 / P0140 Check - Throttle Change Size</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor activity check (P0134 upstream, P0140 downstream): a throttle movement is counted when throttle area changes by at least this between two updates. Stock 1.0 % of full throttle area. The array has room for four O2 sensors; this engine has two, so the third and fourth values are never used. Effect: raise = only larger throttle movements are counted Evidence: ledger:E0995, ledger:E1561</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <LABEL index="2" value="sensor 3 (not fitted, unused)" />
      <LABEL index="3" value="sensor 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34B40" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% area</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.000000</max>
      <MATH equation="X/327.675"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x42A" flags="0x0">
    <title>P0132 / P0138 Check - Start Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor high voltage check (P0132 upstream, P0138 downstream): sampling starts once its run conditions have held for this long. Stock 2.0 s. Effect: raise = conditions must hold longer before sampling starts Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34B4A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x42B" flags="0x0">
    <title>P0131 / P0137 Check - Start Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor low voltage check (P0131 upstream, P0137 downstream): sampling starts once its run conditions have held for this long. Stock 2.0 s. Effect: raise = conditions must hold longer before sampling starts Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34B4C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x42C" flags="0x30">
    <title>O2 Lean In Power Enrichment Check - Enrichment Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor lean in power enrichment check (sets P0131 upstream, P0137 downstream): sampling starts once power enrichment has been active for this long. Stock 2.0 s upstream, 3.0 s downstream. Effect: raise = power enrichment must last longer before the check samples Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34B4E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x42D" flags="0x30">
    <title>O2 Rich In Fuel Cut Check - Fuel Cut Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor rich in deceleration fuel cut check (sets P0132 upstream, P0138 downstream): sampling starts once fuel has been cut for this long. Stock 2.0 s upstream, 3.0 s downstream. The array has room for four O2 sensors; this engine has two, so the third and fourth values are never used. Effect: raise = the fuel cut must last longer before the check samples Evidence: ledger:E0997, ledger:E1561</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <LABEL index="2" value="sensor 3 (not fitted, unused)" />
      <LABEL index="3" value="sensor 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34B56" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x42E" flags="0x30">
    <title>P0131 / P0137 Check Enable - Throttle Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor low voltage check (P0131 upstream, P0137 downstream): samples only while throttle position, with the share used for idle air taken out, is at or above this. Stock 15 %. Effect: lower = the check also samples at smaller throttle openings Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34B5E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x42F" flags="0x30">
    <title>P0131 / P0137 Check Enable - Throttle Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor low voltage check (P0131 upstream, P0137 downstream): samples only while throttle position, with the share used for idle air taken out, is at or below this. Stock 50 %. Effect: raise = the check also samples at larger throttle openings Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34B66" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x430" flags="0x30">
    <title>P0132 / P0138 Check Enable - Throttle Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor high voltage check (P0132 upstream, P0138 downstream): samples only while throttle position, with the share used for idle air taken out, is at or above this. Stock 0 % upstream, 15 % downstream. The array has room for four O2 sensors; this engine has two, so the third and fourth values are never used. Effect: lower = the check also samples at smaller throttle openings Evidence: ledger:E0994, ledger:E1561</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <LABEL index="2" value="sensor 3 (not fitted, unused)" />
      <LABEL index="3" value="sensor 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34B6E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x431" flags="0x30">
    <title>P0132 / P0138 Check Enable - Throttle Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor high voltage check (P0132 upstream, P0138 downstream): samples only while throttle position, with the share used for idle air taken out, is at or below this. Stock 50 %. The array has room for four O2 sensors; this engine has two, so the third and fourth values are never used. Effect: raise = the check also samples at larger throttle openings Evidence: ledger:E0994, ledger:E1561</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <LABEL index="2" value="sensor 3 (not fitted, unused)" />
      <LABEL index="3" value="sensor 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34B76" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x432" flags="0x0">
    <title>O2 Rich In Fuel Cut Check - Enrichment EQ Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor rich in deceleration fuel cut check (sets P0132 upstream, P0138 downstream): after the commanded EQ ratio has been at or above this, the downstream sensor is not checked for about as long as that enrichment lasted. Stock 1.002. Effect: raise = only stronger enrichment holds off the downstream check Evidence: ledger:E0997</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34B7E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x433" flags="0x0">
    <title>O2 Voltage Checks Enable - Commanded EQ Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor low and high voltage checks (P0131 / P0132 / P0137 / P0138) sample only while commanded EQ ratio is at or above this. Stock 0.990. Effect: lower = the checks also sample with a leaner commanded mixture Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34B80" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x434" flags="0x0">
    <title>O2 Voltage Checks Enable - Commanded EQ Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor low and high voltage checks (P0131 / P0132 / P0137 / P0138) sample only while commanded EQ ratio is at or below this. Stock 1.010. Effect: raise = the checks also sample with a richer commanded mixture Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34B82" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x435" flags="0x0">
    <title>P0134 / P0140 Check Enable - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor activity check (P0134 upstream, P0140 downstream): runs only after the engine has been running longer than this. Stock 200 s. Effect: lower = the check can start sooner after a start Evidence: ledger:E0995</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34B84" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x436" flags="0x0">
    <title>P0140 Early Pass - Engine Run Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor activity check, early pass for the downstream sensor (P0140): the early pass can only happen while engine run time is at or below this. Stock 100 s. Effect: raise = the early pass stays available longer after a start Evidence: ledger:E0995</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34B86" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x437" flags="0x0">
    <title>O2 Power Enrichment / Fuel Cut Checks Enable - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor checks made during power enrichment and during deceleration fuel cut only run after the engine has been running longer than this. Stock 200 s. Effect: lower = those checks can run sooner after a start Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34B88" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x438" flags="0x0">
    <title>P0135 Check - Test Duty</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater current check (P0135 upstream, P0141 downstream): upstream heater duty commanded while the check measures heater current. Stock 25 %. Effect: raise = the check measures at a higher duty Evidence: ledger:E1062</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34B94" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x439" flags="0x0">
    <title>P0141 Check - Test Duty</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater current check (P0135 upstream, P0141 downstream): downstream heater duty commanded while the check measures heater current. Stock 25 %. Effect: raise = the check measures at a higher duty Evidence: ledger:E1062</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34B96" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x43A" flags="0x0">
    <title>P0135 / P0141 Check - Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater check (P0135 upstream, P0141 downstream): a test that collects more than this many samples without failing passes. Stock 50. Effect: raise = each heater test is longer Evidence: ledger:E0996</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34B98" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x43B" flags="0x0">
    <title>P0135 / P0141 Check Enable - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater check (P0135 upstream, P0141 downstream): a test only starts while engine speed is at or above this. Stock 1000 rpm. Effect: raise = the test needs a higher rpm to start Evidence: ledger:E0996</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34B9A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x43C" flags="0x0">
    <title>P0135 / P0141 Check Enable - RPM Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater check (P0135 upstream, P0141 downstream): a test only starts while engine speed is at or below this. Stock 2500 rpm. Effect: raise = the test can also start at higher rpm Evidence: ledger:E0996</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34B9C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x43D" flags="0x0">
    <title>P0135 / P0141 Check Enable - Airflow Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater check (P0135 upstream, P0141 downstream): a test only starts while mass airflow is at or above this. Stock 15 g/s. Effect: raise = the test needs more airflow to start Evidence: ledger:E0996</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34B9E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x43E" flags="0x0">
    <title>P0135 / P0141 Check Enable - Airflow Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater check (P0135 upstream, P0141 downstream): a test only starts while mass airflow is at or below this. Stock 30 g/s. Effect: raise = the test can also start at higher airflow Evidence: ledger:E0996</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34BA0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x43F" flags="0x0">
    <title>P0135 / P0141 Check Enable - Coolant Temp Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater check (P0135 upstream, P0141 downstream): a test only starts with coolant temperature at or above this. Stock 70 C. Effect: lower = the test can start on a cooler engine Evidence: ledger:E0996</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34BA2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x440" flags="0x0">
    <title>P0135 / P0141 Check Enable - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater check (P0135 upstream, P0141 downstream): a test only starts once the engine has been running at least this long. Stock 230 s. Effect: lower = the test can start sooner after a start Evidence: ledger:E0996</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34BA4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x441" flags="0x0">
    <title>P0135 / P0141 Check - Time Between Tests</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater check (P0135 upstream, P0141 downstream): a new test only starts once this long has passed since the previous test finished. Stock 20 s. Effect: raise = heater tests are spaced further apart Evidence: ledger:E0996</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34BA6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x442" flags="0x0">
    <title>P0135 / P0141 Check - Test Duty Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater current check (P0135 upstream, P0141 downstream): how long the test duty is applied before current samples are judged. Stock 1 s. Effect: raise = the check waits longer before judging current Evidence: ledger:E1062</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34BA8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x443" flags="0x0">
    <title>P0135 / P0141 Check - Repeat Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater current check (P0135 upstream, P0141 downstream): the check is run again while the number of completed checks this trip is at or below this (stock 1 = two checks per trip). Effect: raise = more heater current checks per trip Evidence: ledger:E1062</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34BAA" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x444" flags="0x30">
    <title>P0135 / P0141 Check - Heater Current Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater current check (P0135 upstream, P0141 downstream): a sample counts against the heater when heater current at the test duty is below this. Stock 0.73 A upstream, 0.60 A downstream. The array has room for four O2 sensors; this engine has two, so the third and fourth values are never used. Effect: raise = more heater current is needed to pass Evidence: ledger:E1062, ledger:E1561</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="upstream (P0135)" />
      <LABEL index="1" value="downstream (P0141)" />
      <LABEL index="2" value="sensor 3 (not fitted, unused)" />
      <LABEL index="3" value="sensor 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34BAC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>A</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x445" flags="0x30">
    <title>P0135 / P0141 Check - Heater Current Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater current check (P0135 upstream, P0141 downstream): a sample counts against the heater when heater current at the test duty is above this. Stock 2.70 A upstream, 2.30 A downstream. The array has room for four O2 sensors; this engine has two, so the third and fourth values are never used. Effect: raise = more heater current is tolerated Evidence: ledger:E1062, ledger:E1561</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="upstream (P0135)" />
      <LABEL index="1" value="downstream (P0141)" />
      <LABEL index="2" value="sensor 3 (not fitted, unused)" />
      <LABEL index="3" value="sensor 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34BB4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>A</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x446" flags="0x30">
    <title>P0134 / P0140 Check - Inactive Voltage Band High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor activity check (P0134 upstream, P0140 downstream): a sample counts as inactive when the sensor reads below this and above the band low limit. Stock 500 mV upstream, 475 mV downstream. The array has room for four O2 sensors; this engine has two, so the third and fourth values are never used. Effect: lower = the inactive band gets narrower Evidence: ledger:E0995, ledger:E1561</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <LABEL index="2" value="sensor 3 (not fitted, unused)" />
      <LABEL index="3" value="sensor 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34BD0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x447" flags="0x30">
    <title>P0134 / P0140 Check - Throttle Changes Needed To Fail</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor activity check (P0134 upstream, P0140 downstream): a failing test window only sets the code if at least this many throttle movements were counted during it, otherwise the window is thrown away. Stock 3. The array has room for four O2 sensors; this engine has two, so the third and fourth values are never used. Effect: raise = more throttle movements are needed before the code can set Evidence: ledger:E0995, ledger:E1561</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <LABEL index="2" value="sensor 3 (not fitted, unused)" />
      <LABEL index="3" value="sensor 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34BD8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>count</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x448" flags="0x30">
    <title>P0131 / P0137 Check - Low Voltage Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor low voltage check (P0131 upstream, P0137 downstream): a sample counts as low when the sensor reads below this. Stock 50 mV. The array has room for four O2 sensors; this engine has two, so the third and fourth values are never used. Effect: raise = higher sensor readings also count as low Evidence: ledger:E0994, ledger:E1561</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <LABEL index="2" value="sensor 3 (not fitted, unused)" />
      <LABEL index="3" value="sensor 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34BE0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x449" flags="0x30">
    <title>P0134 / P0140 Check - Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor activity check (P0134 upstream, P0140 downstream): a test window that reaches this many samples without failing passes. Stock 1000. The array has room for four O2 sensors; this engine has two, so the third and fourth values are never used. Effect: raise = each test window is longer Evidence: ledger:E0995, ledger:E1561</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <LABEL index="2" value="sensor 3 (not fitted, unused)" />
      <LABEL index="3" value="sensor 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34BE8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x44A" flags="0x30">
    <title>O2 Lean In Power Enrichment Check - Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor lean in power enrichment check (sets P0131 upstream, P0137 downstream): a test window that reaches this many samples without failing passes. Stock 100. Effect: raise = each test window is longer Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34BF0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x44B" flags="0x30">
    <title>O2 Rich In Fuel Cut Check - Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor rich in deceleration fuel cut check (sets P0132 upstream, P0138 downstream): a test window that reaches this many samples without failing passes. Stock 100. Effect: raise = each test window is longer Evidence: ledger:E0997</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34BF8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x44C" flags="0x30">
    <title>P0131 / P0137 Check - Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor low voltage check (P0131 upstream, P0137 downstream): a test window that reaches this many samples without failing passes. Stock 1000. Effect: raise = each test window is longer Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C00" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x44D" flags="0x30">
    <title>P0132 / P0138 Check - Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor high voltage check (P0132 upstream, P0138 downstream): a test window that reaches this many samples without failing passes. Stock 150 upstream, 1000 downstream. Effect: raise = each test window is longer Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C08" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x44E" flags="0x30">
    <title>P0134 / P0140 Check - Fail Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor activity check (P0134 upstream, P0140 downstream): a test window fails once more than this many of its samples are inactive. Stock 950. The array has room for four O2 sensors; this engine has two, so the third and fourth values are never used. Effect: raise = more inactive samples are needed to fail a window Evidence: ledger:E0995, ledger:E1561</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <LABEL index="2" value="sensor 3 (not fitted, unused)" />
      <LABEL index="3" value="sensor 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C10" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x44F" flags="0x30">
    <title>P0131 / P0137 Check - Fail Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor low voltage check (P0131 upstream, P0137 downstream): a test window fails once this many of its samples are low. Stock 950. Effect: raise = more low samples are needed to fail a window Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C20" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x450" flags="0x30">
    <title>P0132 / P0138 Check - Fail Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor high voltage check (P0132 upstream, P0138 downstream): a test window fails once this many of its samples are high. Stock 140 upstream, 950 downstream. Effect: raise = more high samples are needed to fail a window Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C30" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x451" flags="0x30">
    <title>O2 Lean In Power Enrichment Check - Fail Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor lean in power enrichment check (sets P0131 upstream, P0137 downstream): the code sets once this many samples in a test window are lean. Stock 95. Effect: raise = more lean samples are needed to set the code Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C38" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x452" flags="0x30">
    <title>O2 Rich In Fuel Cut Check - Fail Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor rich in deceleration fuel cut check (sets P0132 upstream, P0138 downstream): the code sets once this many samples in a test window are rich. Stock 95. Effect: raise = more rich samples are needed to set the code Evidence: ledger:E0997</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C40" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x453" flags="0x30">
    <title>P0131 / P0137 Check - Failed Windows To Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor low voltage check (P0131 upstream, P0137 downstream): the code sets after this many failed test windows in a row. Stock 1. When both sensors fail together, the code is held back for a sensor whose partner sensor has its own failed window flagged, so only the first one reports. Effect: raise = more failed windows in a row are needed to set the code Evidence: ledger:E0994, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C48" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>windows</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x454" flags="0x30">
    <title>P0132 / P0138 Check - Failed Windows To Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor high voltage check (P0132 upstream, P0138 downstream): the code sets after this many failed test windows in a row. Stock 1. When both sensors fail together, the code is held back for a sensor whose partner sensor has its own failed window flagged, so only the first one reports. Effect: raise = more failed windows in a row are needed to set the code Evidence: ledger:E0994, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C4C" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>windows</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x455" flags="0x30">
    <title>P0132 / P0138 Check - High Voltage Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor high voltage check (P0132 upstream, P0138 downstream): a sample counts as high when the sensor reads above this. Stock 1000 mV. Effect: lower = lower sensor readings also count as high Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C60" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x456" flags="0x30">
    <title>O2 Lean In Power Enrichment Check - Lean Voltage Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor lean in power enrichment check (sets P0131 upstream, P0137 downstream): a sample counts as lean when the sensor reads below this while power enrichment is active. Stock 550 mV upstream, 650 mV downstream. Effect: lower = the sensor must read leaner before a sample counts against it Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C68" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x457" flags="0x30">
    <title>O2 Rich In Fuel Cut Check - Rich Voltage Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor rich in deceleration fuel cut check (sets P0132 upstream, P0138 downstream): a sample counts as rich when the sensor reads above this while fuel is cut. Stock 350 mV upstream, 300 mV downstream. The array has room for four O2 sensors; this engine has two, so the third and fourth values are never used. Effect: raise = the sensor must read richer before a sample counts against it Evidence: ledger:E0997, ledger:E1561</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <LABEL index="2" value="sensor 3 (not fitted, unused)" />
      <LABEL index="3" value="sensor 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C70" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x458" flags="0x0">
    <title>P0335 Check Enable - RPM Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crank sensor no-signal check (P0335): only runs while engine speed is below this. Stock 2000 rpm. Effect: raise = the check also runs at higher rpm Evidence: ledger:E1026</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34C94" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x459" flags="0x0">
    <title>P0335 Fail Time - Starter Engaged</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crank sensor no-signal check (P0335): with the starter engaged and the MAF signal either at or above its threshold or faulted, the code sets after this long without a valid crank signal. Stock 4.0 s. Effect: raise = longer cranking without a crank signal before the code sets Evidence: ledger:E1026</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34C96" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x45A" flags="0x0">
    <title>P0335 Check Enable - Airflow Minimum, Signal Lost</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crank sensor no-signal check (P0335): outside the starter-engaged case, the check runs only after a crank signal had been established and while mass airflow is at or above this. Stock 3 g/s. Effect: raise = more airflow is needed for the signal-lost case Evidence: ledger:E1026</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34C9A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x45B" flags="0x0">
    <title>P0335 Fail Time - Signal Lost</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crank sensor no-signal check (P0335): outside the starter-engaged case (crank signal lost while air is still flowing), the code sets after this long without a valid crank signal. Stock 2.0 s. Effect: raise = a longer signal loss is tolerated Evidence: ledger:E1026</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34C9C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x45C" flags="0x30">
    <title>Cam Angle Test - Fail Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam angle test (sets P0017 on this engine; runs with the cam phaser parked): bad samples that set the code. Stock 25. The second value belongs to the other cam input, which this test does not check. The array has room for four cam inputs; this engine has two, so the third and fourth values are never used. Effect: raise = more bad samples are needed to set the code Evidence: ledger:E1080, ledger:E1526</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input reporting P0365 / P0366 / P0017" />
      <LABEL index="1" value="cam input reporting P0340 / P0341 / P0016" />
      <LABEL index="2" value="cam input 3 (not fitted, unused)" />
      <LABEL index="3" value="cam input 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34CE0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x45D" flags="0x30">
    <title>Cam Angle Test - Pass Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam angle test (sets P0017 on this engine; runs with the cam phaser parked): samples without reaching the fail count that pass the test. Stock 35. The second value belongs to the other cam input, which this test does not check. The array has room for four cam inputs; this engine has two, so the third and fourth values are never used. Effect: raise = the test needs more samples to pass Evidence: ledger:E1080, ledger:E1526</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input reporting P0365 / P0366 / P0017" />
      <LABEL index="1" value="cam input reporting P0340 / P0341 / P0016" />
      <LABEL index="2" value="cam input 3 (not fitted, unused)" />
      <LABEL index="3" value="cam input 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34CE8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x45E" flags="0x30">
    <title>Cam Signal Lost Test - Fail Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam position sensor signal lost test (P0365 / P0340): time without the pass counts after which the code sets. Stock 3 s. The array has room for four cam inputs; this engine has two, so the third and fourth values are never used. Effect: raise = the cam signal may be missing longer before the code sets Evidence: ledger:E1080, ledger:E1526</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input reporting P0365 / P0366 / P0017" />
      <LABEL index="1" value="cam input reporting P0340 / P0341 / P0016" />
      <LABEL index="2" value="cam input 3 (not fitted, unused)" />
      <LABEL index="3" value="cam input 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D80" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x45F" flags="0x0">
    <title>P0446 Fail - Vacuum Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP vent restriction check (P0446): with the vent open and purge flowing, time tank vacuum must stay above the vacuum limit to fail. Stock 5 s. Effect: raise = vacuum must persist longer before P0446 sets Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34D98" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x460" flags="0x0">
    <title>P0446 Fail - Vacuum Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP vent restriction check (P0446): tank vacuum, with the vent commanded open and purge flowing, above which the vent is judged restricted. Stock 10 inH2O. Effect: raise = more vacuum is tolerated with the vent open Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34D9A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x461" flags="0x0">
    <title>EVAP Test - Tank at Atmosphere Window, Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test: lower edge of the tank vacuum window that counts as the tank being at atmosphere (negative = pressure). The purge valve check starts and the vent check proceeds only inside the window; tank pressure beyond this edge during the pull-down voids a gross leak failure. Stock -2.5 inH2O. Effect: lower = more tank pressure still counts as atmosphere Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3566E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x462" flags="0x0">
    <title>EVAP Test - Tank at Atmosphere Window, High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test: upper edge of the tank vacuum window that counts as the tank being at atmosphere. Stock 5 inH2O. Effect: raise = more residual vacuum still counts as atmosphere Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35670" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x463" flags="0x0">
    <title>P0446 Pass - Purge Volume</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP vent restriction check (P0446): purge volume that must flow with the vent open, without tank vacuum building, to pass. Stock 10 L. Effect: raise = more purge must flow before the vent check passes Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35674" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>L</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1024.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4194304"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x464" flags="0x0">
    <title>P0446 Fail - Bleed Down Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP vent restriction check (P0446): longest time for the tank vacuum to return to the atmosphere window after the vent is opened; longer fails. Stock 15 s. Effect: raise = the vent may take longer to bleed the vacuum off Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35678" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x465" flags="0x0">
    <title>EVAP Readiness - Counted Drives to Complete</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of counted drives after which the EVAP monitor is reported complete for readiness (stock 6). The PCM can report the evaporative emission (EVAP) monitor as complete for readiness without the engine-running EVAP test having run: a drive counts when the test&#x27;s cold start conditions are not met and the vehicle has been driven at or above the minimum speed for the required time; after enough counted drives the EVAP monitor reads complete. A drive on which the cold start conditions are met clears the count. Effect: lower = the EVAP monitor reads complete after fewer drives Evidence: ledger:E0775, ledger:E1072, ledger:E1356</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35680" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>drives</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x466" flags="0x0">
    <title>EVAP Test - Barometric Pressure Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: lowest barometric pressure at which the test runs. Stock 74 kPa. Effect: lower = the test also runs at higher altitude Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35682" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x467" flags="0x0">
    <title>EVAP Readiness - Counted Drive Minimum Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Driving time toward a counted drive only accumulates at or above this vehicle speed (stock 24 km/h). The PCM can report the evaporative emission (EVAP) monitor as complete for readiness without the engine-running EVAP test having run: a drive counts when the test&#x27;s cold start conditions are not met and the vehicle has been driven at or above the minimum speed for the required time; after enough counted drives the EVAP monitor reads complete. A drive on which the cold start conditions are met clears the count. Effect: raise = a counted drive needs a higher speed Evidence: ledger:E0775, ledger:E1072, ledger:E1356</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35684" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x468" flags="0x0">
    <title>EVAP Readiness - Counted Drive Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Driving time at or above the minimum speed needed for a drive to count (stock 30 s). The PCM can report the evaporative emission (EVAP) monitor as complete for readiness without the engine-running EVAP test having run: a drive counts when the test&#x27;s cold start conditions are not met and the vehicle has been driven at or above the minimum speed for the required time; after enough counted drives the EVAP monitor reads complete. A drive on which the cold start conditions are met clears the count. Effect: raise = a counted drive needs more driving time Evidence: ledger:E0775, ledger:E1072, ledger:E1356</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35688" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x469" flags="0x0">
    <title>EVAP Test - Voltage Out of Range Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: time system voltage may be outside its window before the test is switched off for the trip. Stock 12 s. Effect: raise = a longer voltage excursion is tolerated Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3568C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x46A" flags="0x0">
    <title>EVAP Test - Fuel Level Out of Range Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: time fuel level may be outside its window before the test is switched off for the trip. Stock 15 s. Effect: raise = a longer fuel level excursion is tolerated Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35690" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x46B" flags="0x0">
    <title>EVAP Test - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: lowest system voltage. Stock 11 V. Effect: lower = the test also runs at lower voltage Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35694" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x46C" flags="0x0">
    <title>EVAP Test - System Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: highest system voltage. Stock 18 V. Effect: raise = the test also runs at higher voltage Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35696" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x46D" flags="0x0">
    <title>EVAP Test - Fuel Level Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: lowest fuel level. Stock 15 %. Effect: lower = the test also runs with less fuel Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35698" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x46E" flags="0x0">
    <title>EVAP Test - Intake Air Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: highest intake air temperature. Stock 30 C. Effect: raise = the test also runs in warmer air Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x356B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x46F" flags="0x0">
    <title>EVAP Test - Startup Coolant Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: highest coolant temperature at engine start (the test needs a cold start). Stock 30 C. Effect: raise = the test also runs after a warmer start Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x356B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x470" flags="0x0">
    <title>Fuel Tank Pressure Sensor - Zero Learn Intake Air Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel tank pressure sensor: the zero (tank at atmosphere) is learned at a cold key-on only while intake air temperature is below this and above 4 C. Stock 30 C. Effect: raise = the zero is also learned on warmer starts Evidence: ledger:E1072, ledger:E1073, ledger:E1189</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x356BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x471" flags="0x0">
    <title>EVAP Test - Intake Air Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: lowest intake air temperature. Stock 4 C. Effect: lower = the test also runs in colder air Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x356BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x472" flags="0x0">
    <title>EVAP Test - Fuel Level Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: highest fuel level. Stock 85 %. Effect: raise = the test also runs with a fuller tank Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x356BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x473" flags="0x0">
    <title>Monitor Enable, Minimum Engine Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The EVAP fuel level change check and the fuel tank pressure change check run only after the engine has run this long since start. Stock 10 seconds. Effect: raise = the change checks start later after start-up Evidence: ledger:E0217, ledger:E0775, ledger:E0811, ledger:E1556</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35812" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x474" flags="0x0">
    <title>EVAP Test - Abort Tank Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test: with the vent commanded closed, tank vacuum below this (negative = pressure in the tank) aborts the test for the trip. Stock -2.5 inH2O. Effect: lower = more tank pressure is tolerated before the test is aborted Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35830" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x475" flags="0x0">
    <title>EVAP Test - Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test: engine run time after which an unfinished test is ended for the trip. Stock 1000 s. Effect: raise = the test may finish later in the trip Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3583A" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x476" flags="0x0">
    <title>P0496 Test - Atmosphere Wait</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve leak check (P0496): longest wait for the tank to reach the atmosphere window before the check; after it the check is skipped. Stock 15 s. Effect: raise = the check waits longer for the tank to settle Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35842" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x477" flags="0x0">
    <title>P0496 Fail - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve leak check (P0496): with purge commanded off and the vent closed, time tank vacuum must stay above the limit to fail. Stock 5 s. Effect: raise = vacuum must persist longer before P0496 sets Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35844" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x478" flags="0x0">
    <title>P0496 Test - Manifold Vacuum Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve leak check (P0496): least manifold vacuum for test time to count toward a pass. Stock 0 kPa (always counts). Effect: raise = pass time only counts with more manifold vacuum Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35846" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x479" flags="0x0">
    <title>P0496 Fail - Vacuum Limit, Cold Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve leak check (P0496): tank vacuum, with purge commanded off and the vent closed, above which the purge valve is judged leaking; used when startup coolant is below the cold start temperature. Stock 10 inH2O. Effect: raise = more vacuum is tolerated with purge off Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35848" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x47A" flags="0x0">
    <title>P0496 Fail - Vacuum Limit, Warm Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve leak check (P0496): same limit when startup coolant is at or above the cold start temperature. Stock 10 inH2O. Effect: raise = more vacuum is tolerated with purge off Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3584A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x47B" flags="0x0">
    <title>P0496 Pass - Time, Warm Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve leak check (P0496): time with purge off without the vacuum limit being exceeded that passes the check, warm start. Stock 60 s. Effect: raise = the check runs longer before it passes Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3584E" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x47C" flags="0x0">
    <title>P0496 Test - Cold Start Coolant Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve leak check (P0496): startup coolant temperature below which the cold start limit and pass time are used. Stock 30 C. Effect: raise = more starts use the cold start values Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35858" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x47D" flags="0x0">
    <title>P0455 Test - Tank Pressure Void Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak test (P0455): time the tank may show pressure beyond the low edge of the atmosphere window during the pull-down before a gross leak failure of this test is disregarded. Stock 5 s. Effect: raise = pressure must persist longer before a failure is disregarded Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E62" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x47E" flags="0x0">
    <title>P0455 Pass - Vacuum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak test (P0455): tank vacuum that passes the test when reached during the pull-down. Stock 8 inH2O. Effect: lower = less vacuum is enough to pass the gross leak test Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E64" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x47F" flags="0x0">
    <title>P0455 Fail - Purge Volume</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak test (P0455): purge volume drawn from the sealed system without reaching the pass vacuum that fails the test. Stock 15 L. Effect: raise = more purge may be drawn before the gross leak test fails Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E66" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>L</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1024.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4194304"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x480" flags="0x0">
    <title>Fuel Tank Pressure Sensor - Zero Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel tank pressure sensor: lowest sensor voltage accepted as the zero (tank at atmosphere) when the zero is learned at a cold key-on. Stock 1.20 V. Effect: lower = a lower sensor voltage is accepted as the zero Evidence: ledger:E1073</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E84" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x481" flags="0x0">
    <title>Fuel Tank Pressure Sensor - Zero Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel tank pressure sensor: highest sensor voltage accepted as the zero when the zero is learned at a cold key-on. Stock 1.80 V. Effect: raise = a higher sensor voltage is accepted as the zero Evidence: ledger:E1073</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E86" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x482" flags="0x0">
    <title>Fuel Tank Pressure Sensor - Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel tank pressure sensor: tank vacuum per volt of sensor signal away from the learned zero, used by the engine-running EVAP test. Stock 5.0 inH2O per V. Change only for a different sensor. Effect: raise = the same sensor voltage reads as more vacuum Evidence: ledger:E1073</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E88" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>inH2O per V</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x483" flags="0x0">
    <title>EVAP Re-Check - Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak re-check (runs on a later trip after a gross leak failure, P0455): longest time the re-check keeps trying before it gives up for the trip. Stock 600 s. Effect: raise = the re-check tries longer Evidence: ledger:E1073</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F2E" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x484" flags="0x0">
    <title>EVAP Re-Check - Purge Ramp Down Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak re-check (runs on a later trip after a gross leak failure, P0455): length of the opening step, in which purge is ramped down with the vent closed. Stock 25.5 s. Effect: raise = the opening ramp lasts longer Evidence: ledger:E1073</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F32" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x485" flags="0x0">
    <title>EVAP Re-Check - Pass Vacuum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak re-check (runs on a later trip after a gross leak failure, P0455): tank vacuum that passes the re-check when held for the pass time. Stock 8 inH2O. Effect: lower = less vacuum passes the re-check Evidence: ledger:E1073</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F3A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x486" flags="0x0">
    <title>EVAP Re-Check - Ramp Purge Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak re-check (runs on a later trip after a gross leak failure, P0455): least commanded purge during the opening ramp. Stock 3 %. Effect: raise = purge stays higher during the opening ramp Evidence: ledger:E1073</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F3C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x487" flags="0x0">
    <title>EVAP Re-Check - Purge Ramp Down Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak re-check (runs on a later trip after a gross leak failure, P0455): rate at which commanded purge is lowered during the opening step. Stock 4.7 % per second. Effect: raise = purge is ramped down faster Evidence: ledger:E1073</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F3E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% per s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>102798.201000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*1.5686"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x488" flags="0x0">
    <title>EVAP Re-Check - Pass Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak re-check (runs on a later trip after a gross leak failure, P0455): time tank vacuum must stay at or above the pass vacuum. Stock 5 s. Effect: raise = vacuum must hold longer to pass Evidence: ledger:E1073</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F42" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x489" flags="0x0">
    <title>Fuel Trim Monitor - Purge Off Test Wait Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): longest wait for a result of the purge-off test after a rich reading asked for it; then the request is dropped. Stock 600 s. Effect: raise = the monitor waits longer for the purge-off test Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36266" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x48A" flags="0x0">
    <title>Fuel Trim Monitor - Rich Segments to Fail</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): number of purge-off segments that read rich needed to set P0172. Stock 2. Effect: raise = more rich segments are needed before P0172 sets Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36268" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>segments</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x48B" flags="0x0">
    <title>Fuel Trim Monitor - Not Rich Segments to Pass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): number of purge-off segments that do not read rich needed to pass P0172. Stock 2. Effect: raise = more clean segments are needed to pass Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3626A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>segments</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x48C" flags="0x0">
    <title>Fuel Trim Monitor - Segments per Test</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): most purge-off segments in one test; when they are used up without a verdict the test ends undecided. Stock 3. Effect: raise = a test may run more purge-off segments Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3626C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>segments</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x48D" flags="0x0">
    <title>Fuel Trim Monitor - Unbroken Filtering Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): unbroken filtering time needed before each lean or rich evaluation. Stock 2 s. Effect: raise = evaluations come less often Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36270" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x48E" flags="0x0">
    <title>Fuel Trim Monitor - Purge Off Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): time purge must have been at the test level, with the fuel trim settled, before the purge-off measurement starts. Stock 1 s. Effect: raise = the measurement starts later after purge is shut off Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362BC" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x48F" flags="0x0">
    <title>Fuel Trim Monitor - Purge Restore Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): time after the measurement ends, with the fuel trim settled, before the trim hold is released and normal sampling resumes. Stock 1 s. Effect: raise = normal trim sampling resumes later after a test Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362C0" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x490" flags="0x0">
    <title>Fuel Trim Monitor - Test Start Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): longest wait for the purge control and the fuel trim to accept the test request; after it the attempt is abandoned. Stock 2 s. Effect: raise = the test waits longer to start Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362CC" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x491" flags="0x0">
    <title>Fuel Trim Monitor - Wait After a Test</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): wait before the next test after one in which at least one purge-off segment was evaluated. Stock 300 s. Effect: raise = purge-off tests repeat less often Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362D0" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x492" flags="0x0">
    <title>Fuel Trim Monitor - Ramp Down Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): longest time to bring purge down to the test level in a non-purge fuel trim cell; after it the attempt is abandoned. Stock 10 s. Effect: raise = the ramp down may take longer Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362E8" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x493" flags="0x0">
    <title>Fuel Level Sender Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the PCM&#x27;s filtered fuel level sender voltage follows the raw reading: the fraction of the gap closed per update. Stock 0.99 (almost no filtering). Effect: lower = the sender reading is smoothed more (slower to change) Evidence: ledger:E0956</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x364C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x494" flags="0x0">
    <title>Fuel Level Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the fuel level the PCM reports (fuel level PID) and uses follows the level looked up from the sender: the fraction of the gap closed per update. Stock 0.80. Effect: lower = the reported fuel level is smoothed more (slower to change) Evidence: ledger:E0956</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x364C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x495" flags="0x0">
    <title>Airflow Rationality - Coolant Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101): highest coolant temperature at which the test runs. Stock 125 C. Effect: lower = the test stops at a lower coolant temperature Evidence: ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x496" flags="0x0">
    <title>Airflow Rationality - Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101): lowest coolant temperature at which the test runs. Stock 70 C. Effect: raise = the test waits for a warmer engine Evidence: ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x497" flags="0x0">
    <title>Airflow Rationality - Throttle Airflow Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101), diagnostic model only: filter on the airflow modelled from throttle position; every 6.25 ms the filtered value moves this fraction of the way to the new value. Stock 0.20. Effect: raise = the modelled throttle airflow follows throttle changes faster Evidence: ledger:E1074</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3670E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x498" flags="0x0">
    <title>Airflow Rationality - Pressure Ratio Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101), diagnostic model only: highest ratio of manifold pressure to barometric pressure the throttle airflow model uses; above it the ratio is held and the modelled throttle airflow is capped by the modelled engine airflow. Stock 0.96. Effect: lower = the throttle airflow model is capped from a lower manifold pressure Evidence: ledger:E1074</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36734" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x499" flags="0x0">
    <title>Airflow Rationality - Airflow Difference Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101): filter on the difference between measured airflow and the airflow modelled from throttle position; each update the filtered difference moves this fraction of the way to the new reading. Stock 0.01 (it takes roughly 100 updates, about 10 s, to follow a change). Effect: raise = the airflow check reacts faster and is less smoothed Evidence: ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3673A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x49A" flags="0x0">
    <title>Airflow Rationality - Pressure Difference Limit, Airflow Model</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101): filtered difference, in either direction, between measured manifold pressure and the pressure modelled from measured airflow above which the second pressure check is failing. P0101 and P0106 need this check failing; with the throttle check it gives P1101. Stock 20 kPa. Effect: raise = a larger pressure disagreement is tolerated Evidence: ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36744" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x49B" flags="0x0">
    <title>Airflow Rationality - Throttle Check Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101): filter on the throttle check value (pressure difference times airflow difference); each update the filtered difference moves this fraction of the way to the new reading. Stock 0.01 (it takes roughly 100 updates, about 10 s, to follow a change). Effect: raise = the throttle check reacts faster and is less smoothed Evidence: ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36746" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x49C" flags="0x0">
    <title>Airflow Rationality - Throttle Check Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101): the pressure difference and the airflow difference against the throttle-based model are multiplied and filtered; above this value (both disagree with throttle position in the same direction) the throttle check is failing. Alone this sets P0121, with a failing second pressure check P1101. Stock 350. Effect: raise = a larger combined disagreement is tolerated Evidence: ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36748" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>kPa x g/s</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x49D" flags="0x0">
    <title>Injector Circuit Test - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The injector circuit fault checks (P0201 to P0205) only run after system voltage has stayed above this for the Injector Circuit Test - Voltage OK Time. At or below it the timer restarts and the checks stop. Stock 11.0 V. Effect: raise = the injector circuit checks need a higher system voltage before they run Evidence: ledger:E0772, ledger:E1372</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3679A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x49E" flags="0x0">
    <title>Misfire - Catalyst Test History Depth</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: how many of the most recent 200-revolution windows (16 are stored) are searched for windows that failed the catalyst-damage limit. Stock 16. Effect: lower = only the newest windows count toward a catalyst-damage misfire decision Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3687A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>windows</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x49F" flags="0x0">
    <title>Misfire - Emission Test History Depth</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: how many of the most recent 200-revolution windows (16 are stored) are searched for windows that failed the emission limit. Stock 16. Effect: lower = only the newest windows count toward an emission misfire decision Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3687C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>windows</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A0" flags="0x0">
    <title>Misfire - Idle Exception Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: an event shaped like a disturbance (not a clean misfire) is normally set aside as abnormal. Below this engine speed, with vehicle speed and throttle below their idle exception limits, it is counted as a misfire anyway. Stock 1000 rpm. Effect: raise = the idle exception reaches higher engine speed Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36888" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A1" flags="0x0">
    <title>Misfire - Idle Exception Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: commanded throttle below which the idle exception of the abnormal event test applies. Stock 3.0 %. Effect: raise = the idle exception reaches more throttle Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3688A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A2" flags="0x0">
    <title>Misfire - Idle Exception Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: vehicle speed below which the idle exception of the abnormal event test applies. Stock 5 km/h. Effect: raise = the idle exception reaches higher vehicle speed Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3688C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A3" flags="0x0">
    <title>Misfire - Quiet Cycles That End a Run</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: number of engine cycles in a row without a misfire that ends a run of misfiring cycles. Stock 3. Effect: raise = a run of misfiring cycles lasts across longer quiet gaps Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3688E" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A4" flags="0x0">
    <title>Misfire - Run Counting Start Cycle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: in a run of engine cycles that each show a misfire, the first cycle is counted and then every cycle from this one on; the cycles in between are not counted. Stock 7. Effect: lower = more cycles of a continuous misfire are counted Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3688F" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A5" flags="0x0">
    <title>Misfire - Low Load Pause</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: pause, in engine cycles, requested while load is below the minimum load curve. Stock 4. Effect: raise = the monitor stays paused longer after load rises above the minimum Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368D2" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A6" flags="0x0">
    <title>Misfire - Overspeed Pause</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: pause, in engine cycles, requested at or above the overspeed pause engine speed. Stock 0 (none). Effect: raise = the monitor pauses above the overspeed engine speed Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A7" flags="0x0">
    <title>Misfire - Low Fuel Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: fuel level below which the monitor is paused (misfire from running out of fuel is not reported), unless P0300 is already confirmed. Stock 2.5 %. Effect: raise = the monitor pauses at a higher fuel level Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A8" flags="0x0">
    <title>Misfire - Low Fuel Pause</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: pause, in engine cycles, requested while fuel level is below the low fuel level. Stock 88. Effect: raise = the monitor stays paused longer after a low fuel reading Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A9" flags="0x0">
    <title>Misfire - Low Fuel Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: engine run time before the low fuel pause can be requested. Stock 5 s. Effect: raise = low fuel is ignored for longer after each start Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4AA" flags="0x0">
    <title>Misfire - General Pause</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: pause, in engine cycles, requested while the run conditions are not met, on a crank sync error and during fuel cut. Stock 4. Effect: raise = the monitor stays paused longer after these conditions end Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4AB" flags="0x0">
    <title>Misfire - Emission Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: misfire rate (misfires per 100 cylinder firings, measured over 200 engine revolutions) at or above which the window counts as a failed emission window. Stock 1.0 %. Effect: raise = more misfire is tolerated before the code sets Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37072" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4AC" flags="0x0">
    <title>Misfire - Dead Cylinder Misfire Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: misfires of one cylinder in a 200-revolution window (100 firings of that cylinder) at or above which it is treated as a dead cylinder for the catalyst-damage exemption. Stock 90. Effect: lower = a cylinder is treated as dead at fewer misfires Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37206" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>misfires</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>127.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4AD" flags="0x0">
    <title>Misfire Monitor - Cold Start Release Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: after a start below the cold start limit, the monitor is released once coolant reaches this. Stock 21 degC. Effect: raise = after a cold start the monitor waits for a warmer engine Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3720C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4AE" flags="0x0">
    <title>Misfire Monitor - Cold Start Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: if coolant is at or above this when the monitor is reset at start-up, the monitor is released straight away; otherwise it waits for the cold start release temperature. Stock -7 degC. Effect: raise = more starts count as cold starts Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3720E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4AF" flags="0x0">
    <title>Misfire Monitor - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: system voltage must be at or above this (not checked during the voltage grace time after start). Stock 9 V. Effect: raise = the monitor stops at a higher system voltage Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37210" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4B0" flags="0x0">
    <title>Misfire Monitor - System Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: system voltage must be at or below this (not checked during the voltage grace time after start). Stock 18 V. Effect: lower = the monitor stops at a lower system voltage Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37212" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4B1" flags="0x0">
    <title>Misfire Monitor - Run Time Before Voltage and Pause Checks</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: the system voltage limits are not applied until the engine has run this long. The same run time must pass before the low load pause, the fuel cut pause and the crank sync pause can be requested. Stock 5 s. Effect: raise = voltage, low load and fuel cut are ignored for longer after each start Evidence: ledger:E1038, ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37214" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4B2" flags="0x0">
    <title>Misfire Monitor - Coolant Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: coolant temperature must be at or above this. Stock -7 degC. Effect: raise = the monitor needs a warmer engine Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37216" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4B3" flags="0x0">
    <title>Misfire Monitor - Coolant Temperature Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: coolant temperature must be at or below this. Stock 125 degC. Effect: lower = the monitor stops at a lower coolant temperature Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37218" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4B4" flags="0x0">
    <title>Misfire Monitor - RPM Needing Crank Variation Learned</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: above this engine speed the monitor only runs once the crankshaft variation check (P0315) has reported a pass. Stock 1000 rpm. Effect: raise = the monitor runs to a higher rpm without the crankshaft variation learned Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3721A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4B5" flags="0x0">
    <title>Misfire Monitor - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: engine speed must be at or above this. Stock 450 rpm. Effect: raise = the monitor starts at a higher engine speed Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3721C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4B6" flags="0x0">
    <title>Misfire Monitor - RPM Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: engine speed must be at or below this. Stock 6200 rpm. Effect: lower = the monitor stops at a lower engine speed Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3721E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4B7" flags="0x0">
    <title>Misfire - Single Cylinder Share for P030x</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: when one cylinder holds more than this share of the stored misfire history, the code is reported with that cylinder number (P0301 to P0305) instead of P0300. Stock 90 %. Effect: lower = a cylinder-specific code is reported more readily Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37220" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4B8" flags="0x0">
    <title>Misfire - MIL Flash Fuel Cut Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: the flashing check engine lamp request for catalyst-damaging misfire is dropped once deceleration fuel cut has lasted this long. Stock 3 s. Effect: raise = the lamp keeps flashing longer into a fuel cut Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3722E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4B9" flags="0x0">
    <title>Misfire - MIL Flash Low Load Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: once P0300 is confirmed, the lamp does not flash while load is at or below this and vehicle speed is at or below the low speed limit. Stock 30 %. Effect: raise = the lamp stays steady up to a higher load Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37230" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4BA" flags="0x0">
    <title>Misfire - MIL Flash Trip Window Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: number of catalyst-damaging windows in this trip above which the lamp keeps flashing after the misfire itself has stopped. Stock 65535 (never). Effect: lower = the lamp keeps flashing for the rest of the trip after fewer windows Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37232" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>windows</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4BB" flags="0x0">
    <title>Misfire - MIL Flash Low Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: once P0300 is confirmed, the lamp does not flash while vehicle speed is at or below this and load is at or below the low load limit. Stock 30 km/h. Effect: raise = the lamp stays steady up to a higher speed Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37234" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4BC" flags="0x0">
    <title>P0130 Check - Fail Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): the code sets once this many samples in a test window were taken with the sensor not flagged ready for closed loop. Stock 400. Effect: raise = more not-ready samples are needed to set the code Evidence: ledger:E1004</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3744C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4BD" flags="0x0">
    <title>P0130 Check - Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): a test window that reaches this many samples without failing passes. Stock 500. Effect: raise = each test window is longer Evidence: ledger:E1004</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3744E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4BE" flags="0x0">
    <title>P0130 Check Enable - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): only runs once the engine has been running at least this long. Stock 200 s. Effect: lower = the check can start sooner after a start Evidence: ledger:E1004</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37454" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4BF" flags="0x0">
    <title>P0130 Check Enable - Coolant Temp Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): only runs with coolant temperature at or above this. Stock 70 C. Effect: lower = the check can run on a cooler engine Evidence: ledger:E1004</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37456" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4C0" flags="0x0">
    <title>P0130 Check Enable - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): only runs with system voltage at or above this. Stock 11.0 V. Effect: raise = the check needs a higher voltage to run Evidence: ledger:E1004</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37458" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4C1" flags="0x0">
    <title>P0130 Check Enable - System Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): only runs with system voltage at or below this. Stock 18.0 V. Effect: lower = the check stops at a lower voltage Evidence: ledger:E1004</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3745A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4C2" flags="0x0">
    <title>P0130 Check Enable - Voltage Out Of Range Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): system voltage must stay outside its window for this long before the check is stopped. Stock 3.0 s. Effect: raise = short voltage dips or spikes are ignored for longer Evidence: ledger:E1004</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3745C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4C3" flags="0x0">
    <title>P0130 Check Enable - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): only samples while engine speed is at or above this. Stock 1000 rpm. Effect: raise = the check needs a higher rpm Evidence: ledger:E1004</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3745E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4C4" flags="0x0">
    <title>P0130 Check Enable - RPM Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): only samples while engine speed is at or below this. Stock 3400 rpm. Effect: raise = the check also samples at higher rpm Evidence: ledger:E1004</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37460" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4C5" flags="0x0">
    <title>P0130 Check Enable - Airflow Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): only samples while mass airflow is at or above this. Stock 10 g/s. Effect: raise = the check needs more airflow Evidence: ledger:E1004</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37462" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4C6" flags="0x0">
    <title>P0130 Check Enable - Airflow Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): only samples while mass airflow is at or below this. Stock 50 g/s. Effect: raise = the check also samples at higher airflow Evidence: ledger:E1004</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37464" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4C7" flags="0x0">
    <title>P0130 Check - Start Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): sampling starts once its run conditions have held for this long. Stock 2.0 s. Effect: raise = conditions must hold longer before sampling starts Evidence: ledger:E1004</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37468" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4C8" flags="0x0">
    <title>P0136 Test - Run Condition, Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0136 (downstream O2 sensor swing test): engine run time from which the test routines run. Stock 2 s. Effect: raise = the downstream sensor swing test starts later after each start Evidence: ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3746A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4C9" flags="0x0">
    <title>P0136 Test - Wait Before Fuel Steps</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): the forced fuel steps are only requested once the test has been enabled for longer than this without the sensor reading both low and high on its own. Stock 435 s. Effect: lower = the forced fuel steps are requested sooner Evidence: ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3746C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4CA" flags="0x0">
    <title>P0136 Test - Rich Step Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): the code sets if the sensor has not read high within this long of a rich fuel step that the upstream sensor confirmed. Stock 10 s. Effect: raise = the sensor gets longer to respond to the rich step Evidence: ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3746E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4CB" flags="0x0">
    <title>P0136 Test - Lean Step Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): the code sets if the sensor has not read low within this long of a lean fuel step that the upstream sensor confirmed. Stock 10 s. Effect: raise = the sensor gets longer to respond to the lean step Evidence: ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37470" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x4CC" flags="0x30">
    <title>P0136 Test - Low Voltage Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): the sensor counts as having read low once it is at or below this. Stock 250 mV. Effect: raise = a higher reading already counts as low Evidence: ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="downstream sensor" />
      <LABEL index="1" value="not used" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37478" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4CD" flags="0x30">
    <title>P0136 Test - High Voltage Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): the sensor counts as having read high once it is at or above this. Stock 650 mV. Effect: lower = a lower reading already counts as high Evidence: ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="downstream sensor" />
      <LABEL index="1" value="not used" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3747C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4CE" flags="0x30">
    <title>P0136 Test - Upstream Rich Confirm Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): a rich fuel step only counts against the downstream sensor if the upstream sensor reads at or above this. Stock 550 mV. Effect: lower = a weaker upstream reading confirms the rich step Evidence: ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="upstream sensor" />
      <LABEL index="1" value="not used" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37480" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4CF" flags="0x30">
    <title>P0136 Test - Upstream Lean Confirm Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): a lean fuel step only counts against the downstream sensor if the upstream sensor reads at or below this. Stock 350 mV. Effect: raise = a weaker upstream reading confirms the lean step Evidence: ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="upstream sensor" />
      <LABEL index="1" value="not used" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37484" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4D0" flags="0x30">
    <title>P0136 Test Enable - Short Term Fuel Trim Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): a forced fuel step only starts while short term fuel trim is at or above this. Stock -5 %. Effect: lower = a step can start with more negative trim Evidence: ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>bank</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x374EC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>-100.000000</min>
      <max>99.996948</max>
      <MATH equation="-100+X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4D1" flags="0x30">
    <title>P0136 Test Enable - Short Term Fuel Trim Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): a forced fuel step only starts while short term fuel trim is at or below this. Stock 8 %. Effect: raise = a step can start with more positive trim Evidence: ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>bank</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x374F0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>-100.000000</min>
      <max>99.996948</max>
      <MATH equation="-100+X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4D2" flags="0x30">
    <title>P0030 / P0036 Circuit Check - Fault Count and Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater control circuit checks P0030 (upstream) and P0036 (downstream): the code sets once the first value&#x27;s number of faulted samples is reached; if the second value&#x27;s number of samples is reached first, the check passes and both counts start again. Stock 10 and 12. Effect: raise the first value = more faulted samples are needed to set the code; raise the second = each window is longer Evidence: ledger:E1062</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>value</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="fault samples to fail" />
      <LABEL index="1" value="window samples to pass" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x374FE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x4D3" flags="0x0">
    <title>P0030 / P0036 Check Enable - Ignition Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater circuit check (P0030 upstream, P0036 downstream): only runs with ignition voltage below this. Stock 18.0 V. Effect: lower = the check stops at a lower voltage Evidence: ledger:E1006</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37506" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4D4" flags="0x0">
    <title>P0030 / P0036 Check Enable - Ignition Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater circuit check (P0030 upstream, P0036 downstream): only runs with ignition voltage above this. Stock 11.0 V. Effect: raise = the check needs a higher voltage to run Evidence: ledger:E1006</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37508" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4D5" flags="0x0">
    <title>P0030 / P0036 Check Enable - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater circuit check (P0030 upstream, P0036 downstream): only runs with engine speed at or above this. Stock 425 rpm. Effect: raise = the check needs a higher rpm to run Evidence: ledger:E1006</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3750A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x4D6" flags="0x30">
    <title>P0351 to P0355 Circuit Check - Fault Count and Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Ignition coil circuit checks P0351 to P0355 (one count pair per cylinder): the code sets once the first value&#x27;s number of faulted samples is reached; if the second value&#x27;s number of samples is reached first, the check passes and both counts start again. Stock 20 and 100. Effect: raise the first value = more faulted samples are needed to set the code; raise the second = each window is longer Evidence: ledger:E1058</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>value</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="fault samples to fail" />
      <LABEL index="1" value="window samples to pass" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3754C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4D7" flags="0x30">
    <title>Throttle Area-to-Throttle Curve - Area Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle area points (percent of full area) at which the throttle area to throttle position curve is defined. The commanded and idle throttle area are looked up against these points. Stock 0.07 to 100 %, closely spaced at small openings. Effect: moves the axis of the throttle area to throttle position curve: keep 33 points and keep them rising Evidence: ledger:E0232, ledger:E0424, ledger:E0443, ledger:E0785, ledger:E1184</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24D22" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle area</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4D8" flags="0x30">
    <title>Misfire - RPM Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stored rpm breakpoints (26 points, 400 to 7000 rpm) that index the columns of the misfire table. Effect: moves the axis of every table that uses it: edit with care Evidence: ledger:E0443</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>26</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x368F4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4D9" flags="0x30">
    <title>Fuel - Coolant Breakpoints, shared (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stored coolant breakpoints (17 points) shared by several fuel tables: editing them moves the coolant axis of all of those tables at once. Effect: moves the axis of every table that uses it: edit with care Evidence: ledger:E0443</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26CE4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4DA" flags="0x30">
    <title>Ambient Air Temp Estimate - Engine-Off Soak Time Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off soak time of each point of the flush requirement curve (0 to 25200 s = 7 h). The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it down, and until it reaches zero the estimate can only fall toward the intake air temperature. Axis data: keep ascending. Effect: moves the flush requirement points along soak time Evidence: ledger:E0385, ledger:E1184, ledger:E1334</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3456A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4DB" flags="0x30">
    <title>Idle Air Valve Map - Idle Area Breakpoints (unused, dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle area command breakpoints of the idle air valve position map used by valve-type idle systems. Axis data: keep ascending. The idle air valve driver is not built into this OS and the idle speed controller always uses the electronic throttle path, so this has no effect on this truck (dormant). Effect: no effect on this truck Evidence: ledger:E0443, ledger:E1279</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x295D0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% of throttle area</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>182.041667</max>
      <MATH equation="X/360"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4DC" flags="0x30">
    <title>Idle Air Valve Map - Valve Position vs Idle Area (unused, DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air valve position for each idle area breakpoint, used by valve-type idle systems. Shown as the raw stored value. The idle air valve driver is not built into this OS and the idle speed controller always uses the electronic throttle path, so this has no effect on this truck (dormant). Reference only: DO NOT EDIT. Effect: no effect on this truck Evidence: ledger:E0443, ledger:E0899, ledger:E1279</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29618" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4DD" flags="0x30">
    <title>Driveline Torque Calc - Gear Ratio by Trans State</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Gear ratio by transmission state in the driveline torque estimate: engine torque x converter torque ratio x this ratio x final drive (4.56) x range multiplier. Stock 3.75 / 2.25 / 1.37 / 1.00 / 0.73 / 0 (a five-speed manual&#x27;s set, not the automatic&#x27;s). Reverse uses its own ratio (3.67); Neutral and Park give 0. The estimate feeds the pedal filter axle torque factor and the pedal gain reduction. Effect: changes the driveline torque estimate used by the pedal filter and pedal gain reduction Evidence: ledger:E0444, ledger:E1203</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20062" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>:1</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4DE" flags="0x30">
    <title>Driveline Torque Calc - Range Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier on the driveline torque estimate by the transfer case range state another module sends over the bus (0 to 5; any other value counts as 0): engine torque x converter torque ratio x gear ratio x final drive x this multiplier. State 3 is 4WD-Low and state 4 is 4WD-High (as the PCM reports them in its 4WD status); the sender sets the meaning of 0, 1, 2 and 5. Stock 1.0 except 4WD-Low = 3.332. The estimate feeds the pedal filter axle torque factor and the pedal gain reduction. Effect: changes the driveline torque estimate in that range state Evidence: ledger:E0444, ledger:E1203, ledger:E1205, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>range state (received from the bus)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3 (4WD-Low)" />
      <LABEL index="4" value="4 (4WD-High)" />
      <LABEL index="5" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20054" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>3.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4DF" flags="0x30">
    <title>P0125 - Required Air Mass vs Start-Up Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up check P0125: air mass the engine must have drawn since start, by coolant temperature at start-up, before the check judges whether coolant has reached the target. Stock 8129 g at -40 C falling to 1241 g from 44 C. Effect: raise = the engine gets more time (air) to warm up before P0125 can set Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>degC (start-up coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33740" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E0" flags="0x30">
    <title>P0128 - Required Air Mass vs Start-Up Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Thermostat check P0128: air mass the engine must have drawn since start, by coolant temperature at start-up, before the check judges whether coolant has reached the target. Stock 11973 g at -40 C falling to 3429 g at 80 C. Effect: raise = the engine gets more time (air) to warm up before P0128 can set Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>degC (start-up coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33758" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E1" flags="0x30">
    <title>P0128 - Required Air Mass vs Start-Up Coolant (third column, unused)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Third column of the P0125 / P0128 required air mass curves; the stock instance count (2) leaves it unused. Dormant: no effect on this truck&#x27;s software. Effect: none with the stock instance count Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>degC (start-up coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33770" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E2" flags="0x30">
    <title>Throttle Follower Airflow Ceiling vs RPM</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest follower airflow, by engine speed. Rows: In Gear, Park/Neutral. Stock 32 g/s (no limit). Part of the idle throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. Effect: lower = less follower air allowed at that engine speed Evidence: ledger:E0292, ledger:E0445, ledger:E1187</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="In Gear" />
      <LABEL index="1" value="Park/Neutral" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A8CA" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E3" flags="0x30">
    <title>Catalyst Monitor - Second Fuel Step Commanded EQ</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: commanded EQ ratio during the second fuel step, by airflow. Stock 0.92 at low airflow to 0.93 (7 to 8 % lean). Effect: lower = a leaner second step Evidence: ledger:E1002, ledger:E1020, ledger:E1288</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x32952" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>g/s</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3298E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>EQ</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="1+X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E4" flags="0x30">
    <title>Catalyst Monitor - First Fuel Step Commanded EQ</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: commanded EQ ratio during the first fuel step, by airflow. Stock 1.10 (10 % rich) everywhere. Effect: raise = a richer first step Evidence: ledger:E1002, ledger:E1020, ledger:E1288</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x32952" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>g/s</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x32966" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>EQ</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="1+X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E5" flags="0x30">
    <title>Generator Control - Low Engine Speed Limit vs Desired Idle, In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In gear. While the engine runs at or below this speed, looked up from the desired idle speed, the generator (alternator) control leaves its normal output command and uses its low speed command, until engine speed rises above it or the low speed time limit runs out. Stock 450 rpm at 500 rpm desired idle, 525 rpm from 600 rpm desired idle up. Effect: raise = the generator control switches to its low speed command at a higher engine speed Evidence: ledger:E0445, ledger:E1367</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="500" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="700" />
      <LABEL index="3" value="800" />
      <LABEL index="4" value="900" />
      <LABEL index="5" value="1000" />
      <LABEL index="6" value="1100" />
      <LABEL index="7" value="1200" />
      <LABEL index="8" value="1300" />
      <LABEL index="9" value="1400" />
      <LABEL index="10" value="1500" />
      <LABEL index="11" value="1600" />
      <LABEL index="12" value="1700" />
      <LABEL index="13" value="1800" />
      <LABEL index="14" value="1900" />
      <LABEL index="15" value="2000" />
      <LABEL index="16" value="2100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28F7A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E6" flags="0x30">
    <title>Cold Off-Idle Spark Retard (main spark)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark retard off idle (spark mode 5) below 6000 rpm, by cylinder airmass (rows) and engine speed (columns), multiplied by the coolant factor curve (full to 60 C, half at 70 C, none from 80 C). The larger of this and the catalyst light-off retard is taken off main spark. Stock up to 12 deg at light load (0.08 to 0.28 g/cyl) from 2000 to 4800 rpm. Effect: raise = more spark retard off idle on a cold engine (less torque, more exhaust heat) Evidence: ledger:E0275, ledger:E0445, ledger:E1181</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CE91" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>deg retard</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>63.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E7" flags="0x30">
    <title>P0136 Test Enable - Fuel Trim Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim cells (0 to 38) in which the active test of the downstream oxygen sensor (P0136) may run: the test&#x27;s stable timer only counts while the engine is in a listed cell. Stock lists all 39 cells, so this condition never blocks the test. Effect: remove a cell = the P0136 test cannot run in that cell Evidence: ledger:E0445, ledger:E1355</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>list entry</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <LABEL index="17" value="18" />
      <LABEL index="18" value="19" />
      <LABEL index="19" value="20" />
      <LABEL index="20" value="21" />
      <LABEL index="21" value="22" />
      <LABEL index="22" value="23" />
      <LABEL index="23" value="24" />
      <LABEL index="24" value="25" />
      <LABEL index="25" value="26" />
      <LABEL index="26" value="27" />
      <LABEL index="27" value="28" />
      <LABEL index="28" value="29" />
      <LABEL index="29" value="30" />
      <LABEL index="30" value="31" />
      <LABEL index="31" value="32" />
      <LABEL index="32" value="33" />
      <LABEL index="33" value="34" />
      <LABEL index="34" value="35" />
      <LABEL index="35" value="36" />
      <LABEL index="36" value="37" />
      <LABEL index="37" value="38" />
      <LABEL index="38" value="39" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3748E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>cell</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E8" flags="0x30">
    <title>LTFT Follow Rate per Cell (Fuel Trim Monitor Hold)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per long term fuel trim cell: how fast the applied long term trim moves to its target while the fuel trim monitor holds the trim for its purge-off test, as the fraction of the gap closed per update. In normal operation the follow rate comes from the LTFT follow rate curve by MAP change instead. Stock 0.01 in cells 0 to 20 and 0.99 in cells 21 to 38. Effect: raise = the applied trim reaches its target faster during the monitor&#x27;s hold Evidence: ledger:E0445, ledger:E0954, ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3644C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E9" flags="0x30">
    <title>Manual Gearbox - Gear Detection Bands (rpm per km/h)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Gear k is reported when engine rpm / vehicle speed falls in [low, high) of row k. Used only when the transmission-type switch is 0 (manual); the automatic H3 has it at 1, so these bands are inactive here. Stock centres match gear ratios 3.73 / 2.24 / 1.36 / 0.99 / 0.73; row 6 unused. Effect: none on the automatic H3 Evidence: ledger:E0327, ledger:E0448</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>edge</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="low" />
      <LABEL index="1" value="high" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="5th" />
      <LABEL index="5" value="unused" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20072" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm per km/h</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x4EA" flags="0x0">
    <title>Driveline Torque Calc - Converter Ratio Divisor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Divides the converter torque ratio in the driveline torque calculation (stock 1.0; keep at 1.0). Effect: driveline torque estimate Evidence: ledger:E0327, ledger:E0448</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x20060" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4EB" flags="0x0">
    <title>Idle Speed Control - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: time the idle speed must stay settled before the settle idle offset is removed. Stock 3.75 s. Effect: raise = the settle offset stays longer Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2274A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4EC" flags="0x0">
    <title>Idle Speed Control - Throttle Open Idle Offset Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: time the throttle open idle offset stays on after the throttle closes. Stock 3.75 s. Effect: raise = the offset stays longer after the throttle closes Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2274C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4ED" flags="0x0">
    <title>Idle Speed Control - Settle Error Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: the average rpm error may be above the settle maximum for this long before the settle timer restarts. Stock 1.25 s. Effect: raise = longer excursions are tolerated Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2274E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x4EE" flags="0x30">
    <title>Idle Acquire - RPM Reference Ramp Step vs Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While idle control acquires, the idle rpm reference moves toward desired idle by this many rpm per update, by the reference minus target (negative = reference below target). Stock 0.25 to 3 rpm below, up to 22 rpm above. Effect: raise = reference reaches desired idle faster on the way down / up Evidence: ledger:E0449</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-256" />
      <LABEL index="1" value="-192" />
      <LABEL index="2" value="-128" />
      <LABEL index="3" value="-64" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="64" />
      <LABEL index="6" value="128" />
      <LABEL index="7" value="192" />
      <LABEL index="8" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2276A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm per update</units>
      <decimalpl>0</decimalpl>
      <min>-4096.000000</min>
      <max>4095.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x4EF" flags="0x0">
    <title>Idle Acquire - RPM Reference Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest idle rpm reference and target used while idle control acquires. Stock 625 rpm. Effect: raise = idle acquire never aims below this rpm Evidence: ledger:E0449</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22744" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4F0" flags="0x0">
    <title>Idle Speed Control Acquire - Idle Target Minimum With MAP Sensor Fault</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: lowest idle speed target while the controller is catching the idle speed and a MAP sensor code (P0106 / P0107 / P0108) is failing. Stock 750 rpm (625 rpm without the fault). Effect: raise = higher minimum idle with a failed MAP sensor Evidence: ledger:E1108</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22748" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x4F1" flags="0x30">
    <title>Oil Life - Revolution Weight vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Each engine revolution counts this many times toward oil wear, by corrected coolant temperature. Stock 7 at -40 C, 1 at 72 to 120 C, rising to 64 at the hottest points. Effect: raise = oil life drops faster at that temperature Evidence: ledger:E0450, ledger:E1185</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-24" />
      <LABEL index="2" value="-8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="24" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="56" />
      <LABEL index="7" value="72" />
      <LABEL index="8" value="88" />
      <LABEL index="9" value="104" />
      <LABEL index="10" value="120" />
      <LABEL index="11" value="136" />
      <LABEL index="12" value="152" />
      <LABEL index="13" value="168" />
      <LABEL index="14" value="184" />
      <LABEL index="15" value="200" />
      <LABEL index="16" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x234D0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x4F2" flags="0x0">
    <title>Oil Life - Weighted Revolutions per 0.1 %</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weighted engine revolutions that use up 0.1 % of oil life. Stock 40000. Effect: changes when the oil change reminder comes on Evidence: ledger:E0450, ledger:E1185</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x234C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>revs</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4F3" flags="0x0">
    <title>Oil Life - Steps in a Full Oil Life</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Oil life monitor: number of steps written at an oil life reset; oil life is reported as the steps left divided by this. Stock 1000 (each step is 0.1 %). Effect: raise = more steps (longer oil life) before it reads zero Evidence: ledger:E1060</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x234CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>steps</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4F4" flags="0x0">
    <title>Oil Life - Maximum Distance</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Oil life monitor: distance after an oil life reset at which oil life reads zero whatever the engine has done. Stock 16093 km (10,000 miles). Effect: lower = oil life runs out after a shorter distance Evidence: ledger:E1060</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x234C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4F5" flags="0x0">
    <title>Oil Life - Overheat Zeroing Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant at or above this for the delay below forces oil life to zero, when enabled. Stock 135 C (disabled on the H3). (E0450) Effect: changes when the oil change reminder comes on Evidence: ledger:E0450</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x234C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4F6" flags="0x0">
    <title>Oil Life - Overheat Zeroing Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Oil life monitor: how long coolant must stay at or above the overheat zeroing temperature before oil life is forced to zero (only when overheat zeroing is enabled; it is off in the stock calibration). Stock 3 s. Effect: raise = a longer overheat is needed before oil life is zeroed Evidence: ledger:E1060</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x234CC" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4F7" flags="0x0">
    <title>Oil Life - Overheat Zeroing Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = a severe overheat zeroes oil life. Stock 0 (off). (E0450) Effect: changes when the oil change reminder comes on Evidence: ledger:E0450</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x234B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x4F8" flags="0x30">
    <title>Idle Acquire - Expected MAF vs RPM (In Gear)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow the engine should need at idle in gear, by the idle rpm reference. Idle control finishes acquiring (hands over to closed-loop rpm control) once the measured MAF settles within 0.5 g/s of this. Stock 3.42 / 4.24 / 5.13 / 6.29 / 7.77 g/s at 550 to 950 rpm. Effect: raise = idle acquire expects more airflow before it hands over Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="550" />
      <LABEL index="1" value="650" />
      <LABEL index="2" value="750" />
      <LABEL index="3" value="850" />
      <LABEL index="4" value="950" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2281E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4F9" flags="0x30">
    <title>Idle Acquire - Expected MAF vs RPM (Park/Neutral)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow the engine should need at idle in Park / Neutral, by the idle rpm reference. Idle control finishes acquiring (hands over to closed-loop rpm control) once the measured MAF settles within 0.5 g/s of this. Stock 3.13 / 3.74 / 4.39 / 4.98 / 5.78 g/s at 550 to 950 rpm. Effect: raise = idle acquire expects more airflow before it hands over Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="550" />
      <LABEL index="1" value="650" />
      <LABEL index="2" value="750" />
      <LABEL index="3" value="850" />
      <LABEL index="4" value="950" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2282A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x4FA" flags="0x0">
    <title>Idle Acquire - Expected MAF A/C Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the expected idle airflow while the A/C clutch is engaged. Stock 2.10 g/s. Effect: raise = more airflow expected with A/C on Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2280E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4FB" flags="0x0">
    <title>Idle Acquire - Expected MAF Adder, Alternate (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on this operating system: added to the expected idle airflow only while an internal flag is set, and that flag is never set (E0824, E0842). Stock 1.60 g/s. Effect: no effect at stock (the adder is never applied on this operating system) Evidence: ledger:E0453, ledger:E0824, ledger:E0842</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22810" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4FC" flags="0x0">
    <title>Idle Acquire - MAF Samples Averaged</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAF readings averaged (one per 25 ms) for each expected-airflow comparison. Stock 20 (0.5 s). Effect: raise = slower, steadier comparison Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2280C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>-32768.000000</min>
    <max>32767.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4FD" flags="0x0">
    <title>Idle Acquire - Expected MAF Learn Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Step by which the expected-airflow correction moves toward the measurement after each comparison. Stock 0.25 g/s. Effect: raise = correction learns faster Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22812" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4FE" flags="0x0">
    <title>Idle Acquire - MAF Tolerance to Finish</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Acquire finishes only when two successive mean-MAF readings are within this of the expected airflow. Stock 0.50 g/s. Effect: raise = acquire finishes sooner Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22814" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4FF" flags="0x0">
    <title>Idle Acquire - Max Target RPM to Finish</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Acquire finishes only when the idle rpm target is at or below this. Stock 1500 rpm. Effect: lower = no hand-over at high idle targets Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22816" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x500" flags="0x0">
    <title>Idle Acquire - Min Coolant to Finish</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Acquire finishes only when coolant is at or above this. Stock 60 C. Effect: lower = hand-over allowed on a colder engine Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22818" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x501" flags="0x0">
    <title>Idle Acquire - Completion Engine Speed Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed acquire (the step that brings engine speed down to the desired idle after coming off throttle) only completes and hands over to idle speed control while the engine speed is within this much of the acquire reference speed (absolute error), together with its other conditions. Stock 50 rpm. Effect: raise = idle acquire hands over to idle control with a larger speed error Evidence: ledger:E0453, ledger:E1461</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2281A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x502" flags="0x0">
    <title>P0014 Check Enable - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam position check P0014: the check only runs with system voltage at or above this. Stock 11 V. Effect: raise = the check needs a higher system voltage Evidence: ledger:E1057</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x336EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x503" flags="0x30">
    <title>P0068 Test - Airflow Term vs Engine Speed (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0068 (manifold pressure / airflow vs throttle) airflow leg: this curve by engine speed (600 to 7000 rpm) is compared with the curve by system voltage; when it is at or above that curve the airflow leg counts as failed. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (P0068 test) Evidence: ledger:E0457, ledger:E0899, ledger:E1522</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="600" />
      <LABEL index="1" value="1400" />
      <LABEL index="2" value="2200" />
      <LABEL index="3" value="3000" />
      <LABEL index="4" value="3800" />
      <LABEL index="5" value="4600" />
      <LABEL index="6" value="5400" />
      <LABEL index="7" value="6200" />
      <LABEL index="8" value="7000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23B3A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x504" flags="0x30">
    <title>P0068 Test - Airflow Term vs System Voltage (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0068 (manifold pressure / airflow vs throttle) airflow leg: this curve by system voltage (6 to 14 V) is the limit the engine speed curve is compared with. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (P0068 test) Evidence: ledger:E0457, ledger:E0899, ledger:E1522</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>V</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="6" />
      <LABEL index="1" value="7" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="9" />
      <LABEL index="4" value="10" />
      <LABEL index="5" value="11" />
      <LABEL index="6" value="12" />
      <LABEL index="7" value="13" />
      <LABEL index="8" value="14" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23B4E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x505" flags="0x30">
    <title>P0068 Fail - Pressure Difference</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0068 pressure leg: measured manifold pressure above the pressure modelled from throttle position by more than this, by intake air temperature (-40 to 152 C). P0068 sets when this leg and the airflow leg both hold for the fail time. Stock 25 kPa at every temperature. Effect: raise = a larger pressure disagreement is tolerated Evidence: ledger:E0458, ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23B24" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x506" flags="0x0">
    <title>Vehicle Speed - Min Speed for Primary Source</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this speed the vehicle speed is taken from the transmission output speed instead of the primary speed source. Stock 5.0 km/h. Effect: raise = trans-side speed used up to a higher speed Evidence: ledger:E0460</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x20094" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x507" flags="0x0">
    <title>Vehicle Speed - Factor in 4WD-Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the computed vehicle speed while the transfer case range state is 4WD-Low. Stock 1.00: the speed sensor is after the transfer case. Effect: changes the speed reading in that range only Evidence: ledger:E0460, ledger:E1215</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x20096" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x508" flags="0x0">
    <title>Speed Sensor - Pulses per Mile</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pulses the transmission output-shaft speed sensor makes per mile of travel: sensor pulses per revolution (40) x axle ratio x tire revolutions per mile. Stock 114371 = 40 x 4.56 x 627. The PCM loads it at power-up into two speed sensor timer set-ups, which divide it by 1000 x the timer prescaler. Vehicle speed itself comes from the axle ratio and tire revs, not from this value. After an axle or tire change, set it to 40 x the new axle ratio x the new tire revs per mile so it stays consistent; do not tune it on its own. Effect: keep consistent with the axle ratio and tire revs Evidence: ledger:E0461, ledger:E1575</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x2009C" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>pulses/mi</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>4294967295.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x509" flags="0x0">
    <title>Speed Sensor - Timer Prescaler</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Prescaler the PCM writes to the vehicle speed sensor input timer at power-up. Stock 20. The PCM derives the speed sensor period scale from this and the speed sensor scaling constant together, so changing it alone changes the speed reading. Raw stored value. Reference only: DO NOT EDIT. Effect: reference only (speed sensor input) Evidence: ledger:E0461, ledger:E0899</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x20098" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x50A" flags="0x0">
    <title>Swap - Theft Deterrent (VATS) Fuel Enable Bypass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Swap setting. 0 (stock): after key-on the PCM holds fuel off until the theft deterrent exchange with the body control module on the vehicle bus clears it; with no module answering, the engine cranks but never fuels. 1: the PCM skips that exchange and enables fuel at once, so a PCM moved into an engine swap runs without the donor body control module. Only the fuel enable changes; no password or security data is read or changed. For use on your own engine swap only. Effect: 1 = engine fuels and runs with no body control module; 0 = stock (fuel waits for the theft deterrent exchange) Evidence: ledger:E0461, ledger:E1652</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20988" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0 = stock, 1 = bypass</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x50B" flags="0x0">
    <title>Fuel Trim Monitor - Filtered Data Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): time of filtered trim data needed in this trip before the first lean or rich decision. Stock 20 s. Effect: raise = the first decision of a trip comes later Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3625E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x50C" flags="0x0">
    <title>Fuel Trim Monitor - Lean, Short Term Trim Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): P0171 sets only when the filtered short term trim is also at or above this (1.0 = no correction). Stock 0.75. Effect: raise = a lean failure also needs a higher short term trim Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36298" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x50D" flags="0x0">
    <title>Fuel Trim Monitor - Rich, Short Term Trim Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): a rich reading asks for the purge-off test only when the filtered short term trim is also at or below this (1.0 = no correction). Stock 1.25. Effect: lower = a rich reading also needs a lower short term trim Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3629A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x50E" flags="0x0">
    <title>Fuel Trim Monitor Enable - RPM Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while engine speed is above this. Stock 400 rpm. Narrowing the window makes the monitor run less often. Effect: raise = the monitor needs more engine speed to run Evidence: ledger:E0464, ledger:E0953</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x50F" flags="0x0">
    <title>Fuel Trim Monitor Enable - RPM Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while engine speed is below this. Stock 5700 rpm. Narrowing the window makes the monitor run less often. Effect: lower = the monitor stops at a lower engine speed Evidence: ledger:E0464, ledger:E0953</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x510" flags="0x0">
    <title>Fuel Trim Monitor Enable - Barometric Pressure Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while barometric pressure is above this. Stock 70 kPa (roughly 3000 m altitude). Narrowing the window makes the monitor run less often. Effect: raise = the monitor stops running at a lower altitude Evidence: ledger:E0464, ledger:E0953</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x511" flags="0x0">
    <title>Fuel Trim Monitor Enable - Intake Air Temperature Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while intake air temperature is above this. Stock -20 C. Narrowing the window makes the monitor run less often. Effect: raise = the monitor needs warmer intake air to run Evidence: ledger:E0464, ledger:E0953</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362D8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x512" flags="0x0">
    <title>Fuel Trim Monitor Enable - MAP Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while manifold pressure is above this. Stock 11 kPa. Narrowing the window makes the monitor run less often. Effect: raise = the monitor needs more manifold pressure to run Evidence: ledger:E0464, ledger:E0953</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x513" flags="0x0">
    <title>Fuel Trim Monitor Enable - MAP Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while manifold pressure is below this. Stock 100 kPa. Narrowing the window makes the monitor run less often. Effect: lower = the monitor stops at a lower manifold pressure Evidence: ledger:E0464, ledger:E0953</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x514" flags="0x0">
    <title>Fuel Trim Monitor - Non Purge Cell Purge Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A non purge set cell (cell use 2) is only sampled by the fuel trim monitor while commanded evaporative purge is at or below this. Stock 8 %. The fuel trim monitor (P0171 system too lean, P0172 system too rich) samples the long term fuel trim cell the engine is in; cells 0 to 20 are the purge set and 21 to 38 the non purge set. Effect: raise = non purge cells are sampled with more purge flowing Evidence: ledger:E0397, ledger:E0464, ledger:E1355</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x515" flags="0x0">
    <title>Fuel Trim Monitor - Low Fuel Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): fuel level below which the low fuel guard can apply. Stock 10 %. Effect: raise = the low fuel guard applies at a higher fuel level Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x516" flags="0x0">
    <title>Fuel Trim Monitor - Low Fuel Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): time the fuel level must stay below the low fuel level before the low fuel guard applies (the lean reading is then capped so that running out of fuel does not set P0171). Stock 30 s. Effect: raise = the low fuel guard takes longer to apply Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36262" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x517" flags="0x0">
    <title>Fuel Trim Monitor - Cell Settle Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only samples a fuel trim cell once the engine has stayed in that cell for this many updates in a row. Stock 5. Effect: raise = the engine must stay in a trim cell longer before the monitor samples it Evidence: ledger:E0466, ledger:E0962</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36274" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x518" flags="0x30">
    <title>Fuel Trim Monitor - Non Purge Rich Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): long term trim measured with purge off at or below which a purge-off segment counts as rich; enough rich segments set P0172. Stock 0.80. The lookup input is fixed, so only the first value is used; set all 17 the same. Effect: lower = more removed fuel is tolerated before P0172 sets Evidence: ledger:E0467, ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3635C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x519" flags="0x30">
    <title>Fuel Trim Monitor - Rich Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): filtered long term trim at or below which the system is suspected rich and the purge-off test is requested (0.81 = 19 % fuel removed). P0172 is decided by the purge-off test, not by this value alone. Stock 0.81. The lookup input is fixed, so only the first value is used; set all 17 the same. Effect: lower = more removed fuel is tolerated before the purge-off test is requested Evidence: ledger:E0467, ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36338" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x51A" flags="0x30">
    <title>Fuel Trim Monitor - Lean Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): filtered long term trim at or above which the system is judged lean and P0171 sets (1.0 = no correction, 1.24 = 24 % fuel added). Stock 1.24. The lookup input is fixed, so only the first value is used; set all 17 the same. Effect: raise = more added fuel is tolerated before P0171 sets Evidence: ledger:E0467, ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36314" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x51B" flags="0x0">
    <title>Catalyst Monitor Enable - Throttle Change Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: the test only stays active while throttle position has varied by no more than this since it started tracking. Stock 50 %. Effect: lower = smaller throttle movements stop the test Evidence: ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x51C" flags="0x0">
    <title>Catalyst Monitor Enable - Airflow Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only runs while mass airflow is at or above this (with engine speed near desired idle, see the RPM Above / Below Idle limits). Stock 2.0 g/s. Effect: raise = the test needs more airflow to run Evidence: ledger:E0468, ledger:E0919, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32902" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x51D" flags="0x0">
    <title>Catalyst Monitor Enable - Airflow Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only runs while mass airflow is at or below this (with engine speed near desired idle, see the RPM Above / Below Idle limits). Stock 12.0 g/s. Effect: raise = the test also runs at higher airflow Evidence: ledger:E0468, ledger:E0919, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32904" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x51E" flags="0x0">
    <title>Catalyst Monitor Enable - RPM Above Idle Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: how far engine rpm may be above desired idle rpm for the test to run. Stock 500 rpm. Effect: raise = the test tolerates a higher rpm above idle Evidence: ledger:E0468, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32906" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x51F" flags="0x0">
    <title>Catalyst Monitor Enable - RPM Below Idle Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: how far engine rpm may be below desired idle rpm for the test to run. Stock 500 rpm. Effect: raise = the test tolerates a lower rpm below idle Evidence: ledger:E0468, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32908" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x520" flags="0x0">
    <title>Catalyst Monitor - Settle Time, Just Out of Park / Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): settle time before the test proceeds when the transmission has just come out of Park, Neutral or Reverse and the truck has not driven off since. Stock 5 s. Effect: raise = the test waits longer after a range change Evidence: ledger:E0468, ledger:E0998, ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x521" flags="0x0">
    <title>Catalyst Monitor - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): settle time at idle before the test proceeds (the shorter time, used when the truck was not just shifted out of Park, Neutral or Reverse). Stock 3 s. Effect: raise = the test waits longer at idle before it starts Evidence: ledger:E0468, ledger:E0998, ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x522" flags="0x0">
    <title>Catalyst Monitor - Closed Throttle Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: commanded throttle position, with the share used for idle air taken out, at or below this counts as closed throttle. Stock 5 %. Effect: raise = larger throttle openings still count as closed Evidence: ledger:E0999</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x523" flags="0x0">
    <title>Catalyst Monitor - Closed Throttle Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: once the throttle has stayed closed longer than this, the readiness counter is reset and the test cannot arm. Stock 90 s. Effect: raise = the test can still arm after a longer closed-throttle period Evidence: ledger:E0469, ledger:E0998, ledger:E0999</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328F8" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x524" flags="0x0">
    <title>Catalyst Monitor - Tests per Engine Run</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): most catalyst tests that may be started in one engine run. Stock 12. Effect: lower = fewer catalyst tests are started per engine run Evidence: ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328EC" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>tests</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x525" flags="0x0">
    <title>Catalyst Monitor - Readiness Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: count its readiness counter must reach before the test may arm. The counter goes up by one on each pass with its input condition true and down by one otherwise. Stock 60. Effect: raise = more passes are needed before the test may arm Evidence: ledger:E0469, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328ED" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x526" flags="0x0">
    <title>Catalyst Monitor - New Catalyst Warm-Up Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) on a new catalyst: run time counts toward the warm-up time only while the modelled catalyst temperature is at or above this. Stock 500 C. Effect: raise = only hotter running counts toward releasing the new-catalyst delay Evidence: ledger:E0470, ledger:E1082, ledger:E1188</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32910" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>1023.984375</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/64"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x527" flags="0x0">
    <title>Catalyst Monitor - New Catalyst Warm-Up Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) on a new catalyst: the test stays off until the catalyst has spent this much time in total at or above the warm-up temperature. The total is kept between drives. Stock 3600 s (1 hour). Effect: raise = the catalyst test starts later in the life of a new catalyst Evidence: ledger:E0470, ledger:E1188</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3290C" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x528" flags="0x0">
    <title>Catalyst Temperature Model - Spark Retard Reference Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Subtracted from the torque model&#x27;s best torque (MBT) spark to form the reference the spark retard is divided by: the retard term&#x27;s axis is retard from MBT / (MBT spark minus this). Stock -20 deg, so the reference is MBT spark + 20 deg. The catalyst temperature model (used by catalyst overtemperature protection) moves toward a target built from engine speed and airflow, vehicle speed, commanded fuel ratio, spark retard and an rpm term. Effect: raise = the same retard reads as a larger fraction, so the retard term rises sooner Evidence: ledger:E0473, ledger:E1457</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x218C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x529" flags="0x0">
    <title>Catalytic Converter Protection Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the catalytic converter over-temperature protection on or off, as in the 0411 item. 1 (stock): when the PCM&#x27;s catalyst temperature estimate is above the protection entry temperature, it requests extra fuel (equivalence ratio 1.04 at low throttle, more at higher throttle) to cool the converter. 0: no protection enrichment is ever requested. Turning it off can overheat a catalytic converter under sustained load. Effect: 0 = no catalyst protection enrichment; 1 = stock Evidence: ledger:E0474, ledger:E0805, ledger:E0821, ledger:E1741</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x21E6A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on (stock), 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x52A" flags="0x0">
    <title>Catalyst Over-Temp Protection - Low Throttle EQ</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst over-temperature protection (catalyst temperature model): the commanded EQ requested while protection is active at low throttle. Stock 1.040 (lambda 0.96). Effect: raise = richer protection fuel at low throttle Evidence: ledger:E1043</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x21E6C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x52B" flags="0x0">
    <title>Catalyst Hot-Confirm Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the modelled catalyst temperature must stay above the catalyst over-temperature entry threshold before the catalyst-hot confirm flag sets. Stock 5 s. Effect: raise = longer hot dwell required before the confirm flag is set Evidence: ledger:E0475</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x21E6E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x52C" flags="0x0">
    <title>Catalyst Hot Duty Cycle Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of total run time the catalyst may spend hot (above the over-temperature entry threshold) before the catalyst-hot duty flag sets. Stock 4.00 %. Effect: raise = catalyst must run hot a larger fraction of total run time before a flag is set Evidence: ledger:E0475</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x21E70" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x52D" flags="0x0">
    <title>Cruise - Brake Press Required Before Engage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Swap setting. 1 (stock): cruise control can engage only after the brake pedal has been pressed once since key on. 0: that first brake press is not required, for engine swaps whose brake switch wiring does not give the PCM this signal. Effect: 0 = cruise can engage without a first brake press; 1 = stock Evidence: ledger:E0476, ledger:E1727, ledger:E1742</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x21E72" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = required (stock), 0 = not required</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x52E" flags="0x30">
    <title>Torque Limit - Park / Neutral Converter Output Torque vs Torque Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In Park or Neutral: when engine torque multiplied by the torque converter&#x27;s torque ratio (the torque the converter puts out) rises above this, a torque reduction is applied. Looked up by converter torque ratio (1.0 to 2.5). Stock 992 Nm at every ratio. Effect: lower = the Park / Neutral torque reduction starts at less torque Evidence: ledger:E0481, ledger:E0917, ledger:E1255</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>converter torque ratio x8192</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="8192" />
      <LABEL index="1" value="8960" />
      <LABEL index="2" value="9728" />
      <LABEL index="3" value="10496" />
      <LABEL index="4" value="11264" />
      <LABEL index="5" value="12032" />
      <LABEL index="6" value="12800" />
      <LABEL index="7" value="13568" />
      <LABEL index="8" value="14336" />
      <LABEL index="9" value="15104" />
      <LABEL index="10" value="15872" />
      <LABEL index="11" value="16640" />
      <LABEL index="12" value="17408" />
      <LABEL index="13" value="18176" />
      <LABEL index="14" value="18944" />
      <LABEL index="15" value="19712" />
      <LABEL index="16" value="20480" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20032" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x52F" flags="0x0">
    <title>Closed Throttle Flag - Release Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM&#x27;s closed-throttle flag sets when throttle position is at or below its enter threshold (0.10 % stock) and clears again when throttle rises above that threshold plus this amount. Stock 0.10 %. Effect: raise = the throttle must open further before the closed-throttle flag clears Evidence: ledger:E0485, ledger:E0717, ledger:E0987</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x31A42" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.001526</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.34"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x530" flags="0x0">
    <title>Closed Throttle Flag - Set Below Measured Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed throttle flag (used by the A/C compressor control to hold the compressor off just after the throttle closes): the flag can only set while the measured throttle area above the idle area is at or below this (not checked while the throttle is under idle speed control). Stock 5 %. Effect: raise = the flag may set with the throttle plate still further open Evidence: ledger:E1137</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31A44" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x531" flags="0x30">
    <title>Cruise Control Demand Target vs MAP x Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control demand target by engine load (MAP, rows) and vehicle speed (columns, 38 to 180 km/h). While cruise holds speed, the controller moves its demand toward this value corrected by the speed error, and the demand is turned into a throttle request by the Cruise Control Throttle Area curve (a lower demand means more throttle). Values are the controller&#x27;s internal demand counts. Shown raw. DO NOT EDIT. Effect: raise = the cruise target is allowed to ramp faster toward its new value Evidence: ledger:E0489, ledger:E0688, ledger:E0730, ledger:E0899, ledger:E0943, ledger:E0944</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.9" />
      <LABEL index="2" value="55.8" />
      <LABEL index="3" value="64.6" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.4" />
      <LABEL index="6" value="91.2" />
      <LABEL index="7" value="100.1" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.9" />
      <LABEL index="10" value="126.8" />
      <LABEL index="11" value="135.6" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.4" />
      <LABEL index="14" value="162.2" />
      <LABEL index="15" value="171.1" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2213E" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x532" flags="0x0">
    <title>Fuel Trim Monitor - Purge Off Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): longest purge-off measurement; after it the attempt is abandoned. Stock 35 s. Effect: raise = purge may stay off longer in one attempt Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362E4" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x533" flags="0x0">
    <title>Fuel Trim Monitor - Out of Cell Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): longest time during the purge-off measurement outside a usable non-purge fuel trim cell; after it the attempt is abandoned. Stock 2 s. Effect: raise = the measurement tolerates longer excursions Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362DC" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x534" flags="0x0">
    <title>Fuel Trim Monitor - Wait After an Unfinished Test</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): wait before the next test when no purge-off segment could be evaluated (wait limit or attempt limit reached). Stock 1200 s (20 minutes). Effect: raise = purge-off tests repeat less often after an unfinished one Evidence: ledger:E0498, ledger:E0898, ledger:E0900, ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362E0" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x535" flags="0x0">
    <title>Fuel Trim Monitor - Purge Restored Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): longest time purge runs normally between two purge-off segments; the next segment starts sooner once enough purge has flowed. Stock 30 s. Effect: raise = the pause between purge-off segments may last longer Evidence: ledger:E0499, ledger:E0898, ledger:E0900, ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36282" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x536" flags="0x0">
    <title>Fuel Trim Monitor - Unused Count (no effect)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor: read only on a path the stock program never takes (its condition flag is cleared earlier in the same pass). Changing it has no effect. Stock 100. Effect: no effect Evidence: ledger:E0499, ledger:E0898, ledger:E0900, ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3625C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x537" flags="0x0">
    <title>Fuel Trim Monitor - Short Term Trim Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): filter on the short term trim the lean and rich decisions use; each 100 ms sample moves the filtered value this fraction of the way to the new reading. Stock 0.20. Effect: raise = the filtered short term trim follows faster Evidence: ledger:E0500, ledger:E0898, ledger:E0900, ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36296" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x538" flags="0x0">
    <title>Fuel Trim Monitor - Long Term Trim Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): filter on the long term trim the lean and rich decisions use; each 100 ms sample moves the filtered value this fraction of the way to the new reading. Stock 0.16. Effect: raise = the filtered long term trim follows faster Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36292" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x539" flags="0x0">
    <title>Fuel Trim Monitor - Non Purge Trim Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): filter on the long term trim measured with purge off (used by the purge-off test); fraction per 100 ms sample. Stock 0.10. Effect: raise = the filtered non-purge trim follows faster Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36294" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x53A" flags="0x0">
    <title>Engine-Off Timer Diagnostic (P2610) - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The engine-off timer diagnostic (P2610) checks that the PCM&#x27;s engine-off timer counts once per second against the PCM&#x27;s own clock: a count every 0.59 to 1.39 s is a good sample, 3 bad samples set the code and 10 samples pass it. Set to 0 the diagnostic never runs. Stock 1 (on). Effect: 0 = the engine-off timer diagnostic is switched off Evidence: ledger:E0508, ledger:E0829</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37510" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>on/off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x53B" flags="0x0">
    <title>Engine-Off Timer Diagnostic (P2610) - Minimum Intake Air Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The engine-off timer diagnostic (P2610) checks that the PCM&#x27;s engine-off timer counts once per second against the PCM&#x27;s own clock: a count every 0.59 to 1.39 s is a good sample, 3 bad samples set the code and 10 samples pass it. It only runs while intake air temperature is at or above this value. Stock -40 C. Effect: raise = the engine-off timer diagnostic stops running in colder intake air Evidence: ledger:E0508, ledger:E0829</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37520" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x53C" flags="0x0">
    <title>Engine-Off Timer Diagnostic (P2610) - Maximum Intake Air Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The engine-off timer diagnostic (P2610) checks that the PCM&#x27;s engine-off timer counts once per second against the PCM&#x27;s own clock: a count every 0.59 to 1.39 s is a good sample, 3 bad samples set the code and 10 samples pass it. It only runs while intake air temperature is at or below this value. Stock 125 C. Effect: lower = the engine-off timer diagnostic stops running in hotter intake air Evidence: ledger:E0508, ledger:E0829</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37522" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x53D" flags="0x0">
    <title>Fuel Trim Monitor Stage Enable - RPM Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. One of the fuel trim monitor&#x27;s (P0171 system too lean, P0172 system too rich) conditions for running its test stages: engine speed must be above this. Stock 500 rpm. Narrowing the window makes the monitor run less often. Effect: raise = the monitor&#x27;s stages need more engine speed to run Evidence: ledger:E0522, ledger:E0734, ledger:E0961</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x53E" flags="0x0">
    <title>Fuel Trim Monitor Stage Enable - MAP Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. One of the fuel trim monitor&#x27;s (P0171 system too lean, P0172 system too rich) conditions for running its test stages: manifold pressure must be above this. Stock 11 kPa. Narrowing the window makes the monitor run less often. Effect: raise = the monitor&#x27;s stages need more manifold pressure to run Evidence: ledger:E0522, ledger:E0734, ledger:E0961</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x53F" flags="0x0">
    <title>Fuel Trim Monitor Stage Enable - MAP Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. One of the fuel trim monitor&#x27;s (P0171 system too lean, P0172 system too rich) conditions for running its test stages: manifold pressure must be below this. Stock 100 kPa. Narrowing the window makes the monitor run less often. Effect: lower = the monitor&#x27;s stages stop at a lower manifold pressure Evidence: ledger:E0522, ledger:E0734, ledger:E0961</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x540" flags="0x0">
    <title>Fuel Trim Monitor - Rich Segment, Short Term Trim Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): a purge-off segment counts as rich only when the filtered short term trim is also at or below this. Stock 1.25. Effect: lower = a rich segment also needs a lower short term trim Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3629C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x541" flags="0x0">
    <title>Fuel Trim Monitor - Purge Off Attempts</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): number of times purge may be shut off before the test is sent to its long wait. Stock 30. Effect: lower = the test gives up after fewer purge shut-offs Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36264" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>attempts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x542" flags="0x30">
    <title>Fuel Trim Monitor - Purge Ramp Down Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): amount commanded purge is lowered every 100 ms when the test shuts purge off, by the purge command at the start of the ramp (0 to 100 %). Stock 199.8 % (purge off at once) up to 25 % purge, 10 % per step above. Effect: lower = purge is shut off more gradually Evidence: ledger:E0525, ledger:E0734, ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% commanded purge</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.275" />
      <LABEL index="2" value="12.55" />
      <LABEL index="3" value="18.825" />
      <LABEL index="4" value="25.1" />
      <LABEL index="5" value="31.375" />
      <LABEL index="6" value="37.65" />
      <LABEL index="7" value="43.925" />
      <LABEL index="8" value="50.2" />
      <LABEL index="9" value="56.475" />
      <LABEL index="10" value="62.75" />
      <LABEL index="11" value="69.025" />
      <LABEL index="12" value="75.3" />
      <LABEL index="13" value="81.575" />
      <LABEL index="14" value="87.85" />
      <LABEL index="15" value="94.125" />
      <LABEL index="16" value="100.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x363C8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% per step</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.781250</max>
      <MATH equation="X/326.4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x543" flags="0x0">
    <title>Fuel Trim Monitor - Purge Level During Test</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): commanded purge held while the non-purge trim is measured (the end point of the ramp down). Stock 0 %. Effect: raise = some purge keeps flowing during the purge-off measurement Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x544" flags="0x0">
    <title>Fuel Trim Monitor - Purge Off Segment Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): length of one purge-off segment, counted while the non-purge trim filter is running. Stock 7 s. Effect: raise = each purge-off segment lasts longer Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36272" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x545" flags="0x0">
    <title>P1574 Check - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): the check only runs while engine speed is at or above this. Stock 500 rpm. Effect: raise = the check needs a higher engine speed Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3753C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x546" flags="0x0">
    <title>P1574 Check - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): engine speed must have been above the rpm minimum for this long before the check starts. Stock 1 s. Effect: raise = the check starts later Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3753E" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x547" flags="0x0">
    <title>Secondary Air - Pump Request Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Secondary air injection (AIR). Time after AIR is enabled before the pump request turns on. Stock 0 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (the pump request turns on this long after secondary air is enabled) Evidence: ledger:E0531, ledger:E0836, ledger:E1578</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2C9FA" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x548" flags="0x0">
    <title>Secondary Air - Pump Run-On Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Secondary air injection (AIR). After AIR is no longer enabled, the pump request is cleared once this much time has passed. Stock 8.0 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (longer = the pump keeps running longer after secondary air is no longer enabled) Evidence: ledger:E0531, ledger:E0836, ledger:E1578</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2C9F2" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x549" flags="0x0">
    <title>Secondary Air - Pump Early Stop Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Secondary air injection (AIR). After AIR is no longer enabled, an early stop request can clear the pump request only after this time. Stock 0.15 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (longer = an early stop request must wait longer before it can stop the pump) Evidence: ledger:E0531, ledger:E0836, ledger:E1578</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2C9F3" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x54A" flags="0x0">
    <title>Secondary Air - Pump Stop Delay With Stop Request</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Secondary air injection (AIR). With the stop request set, the pump request is cleared after this time. Stock 0.15 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (longer = the pump stops later after a stop request) Evidence: ledger:E0531, ledger:E0836, ledger:E1578</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2C9F4" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x54B" flags="0x30">
    <title>Secondary Air - Run Time vs Catalyst Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long secondary air runs after it turns on, by modelled catalyst temperature at the start (200 to 1000 C). Stock 0 at every point. Secondary air injection is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0532, ledger:E0836, ledger:E1193</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (catalyst temperature model)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="200" />
      <LABEL index="1" value="250" />
      <LABEL index="2" value="300" />
      <LABEL index="3" value="350" />
      <LABEL index="4" value="400" />
      <LABEL index="5" value="450" />
      <LABEL index="6" value="500" />
      <LABEL index="7" value="550" />
      <LABEL index="8" value="600" />
      <LABEL index="9" value="650" />
      <LABEL index="10" value="700" />
      <LABEL index="11" value="750" />
      <LABEL index="12" value="800" />
      <LABEL index="13" value="850" />
      <LABEL index="14" value="900" />
      <LABEL index="15" value="950" />
      <LABEL index="16" value="1000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CA3E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x54C" flags="0x30">
    <title>Secondary Air - Fuel Correction Time vs Catalyst Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the secondary air fuel correction stays active after air turns on, by modelled catalyst temperature at the start (200 to 1000 C). Stock 0 at every point. Secondary air injection is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0532, ledger:E0836, ledger:E1193</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (catalyst temperature model)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="200" />
      <LABEL index="1" value="250" />
      <LABEL index="2" value="300" />
      <LABEL index="3" value="350" />
      <LABEL index="4" value="400" />
      <LABEL index="5" value="450" />
      <LABEL index="6" value="500" />
      <LABEL index="7" value="550" />
      <LABEL index="8" value="600" />
      <LABEL index="9" value="650" />
      <LABEL index="10" value="700" />
      <LABEL index="11" value="750" />
      <LABEL index="12" value="800" />
      <LABEL index="13" value="850" />
      <LABEL index="14" value="900" />
      <LABEL index="15" value="950" />
      <LABEL index="16" value="1000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CA62" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x54D" flags="0x30">
    <title>Shift Lamp - Barometric Factor on the Pedal Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift lamp request (a data bus signal for a manual transmission upshift lamp): factor by barometric pressure on the highest pedal position at which the lamp may show. Stock 0.51 at 50 kPa rising to 1.12 at 114 kPa. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E1129, ledger:E1143</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>kPa baro</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="50" />
      <LABEL index="1" value="66" />
      <LABEL index="2" value="82" />
      <LABEL index="3" value="98" />
      <LABEL index="4" value="114" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CA96" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x54E" flags="0x30">
    <title>Tip-In Spark Advance Multiplier - Recovery at Engine Start vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in spark advance, knock learned multiplier (the advance is multiplied by it; 1.0 = full advance). Added to the multiplier at each engine start, by coolant. Stock 1.0 (full recovery) up to 40 C, 0.2 at 50 C, 0.1 at 60 C and 0 above. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = more of the advance is given back at a start Evidence: ledger:E1142</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CDD4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x54F" flags="0x0">
    <title>Tip-In Spark Advance Multiplier - Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in spark advance, knock learned multiplier (the advance is multiplied by it; 1.0 = full advance). The multiplier is never allowed below this. Stock 1.0, which pins it at full advance and switches the knock learning of the multiplier off. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: lower = knock during tip-in events is allowed to reduce the advance Evidence: ledger:E1129, ledger:E1142</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2CDD0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x550" flags="0x30">
    <title>Crank-Timed Output - Delay Compensation Time vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Delay time compensated on the crank-timed output events, by engine speed: the time is turned into crank angle at the current speed and the events are scheduled that much earlier. Stock 0.14 ms at low speed falling to 0.10 ms from 4096 rpm. Effect: raise = the crank-timed output events happen earlier at that engine speed Evidence: ledger:E0536, ledger:E1272</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1024" />
      <LABEL index="2" value="2048" />
      <LABEL index="3" value="3072" />
      <LABEL index="4" value="4096" />
      <LABEL index="5" value="5120" />
      <LABEL index="6" value="6144" />
      <LABEL index="7" value="7168" />
      <LABEL index="8" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CE12" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ms</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x551" flags="0x30">
    <title>Idle Spark Minimum vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower limit on spark advance in idle spark mode, by coolant temperature (-40 to 120 C). The idle maximum still wins if the two cross. Stock 5 deg up to 0 C, 0 deg from 10 to 40 C, falling to -5 deg from 80 C. Effect: raise = higher spark advance floor at idle Evidence: ledger:E0543, ledger:E0718, ledger:E1219</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-39.998" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20.002" />
      <LABEL index="3" value="-10.004" />
      <LABEL index="4" value="-0.006" />
      <LABEL index="5" value="9.992" />
      <LABEL index="6" value="19.99" />
      <LABEL index="7" value="29.988" />
      <LABEL index="8" value="39.986" />
      <LABEL index="9" value="49.984" />
      <LABEL index="10" value="59.982" />
      <LABEL index="11" value="69.98" />
      <LABEL index="12" value="79.978" />
      <LABEL index="13" value="89.976" />
      <LABEL index="14" value="99.974" />
      <LABEL index="15" value="109.972" />
      <LABEL index="16" value="119.97" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2ECC6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x552" flags="0x0">
    <title>EVAP Engine-Off Test - Re-Vent Count Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: number of re-vents allowed in the vacuum phase; one more ends the test with what it has. Stock 3. Effect: raise = more re-vents are allowed before the test is ended Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D1A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x553" flags="0x0">
    <title>EVAP Engine-Off Service Test - Result Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP service test (the scan tool started version of the leak test): how long the finished test holds its result before it ends. Stock 600 s. Effect: raise = the service test stays in its final step longer Evidence: ledger:E0554, ledger:E1055</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3427E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x554" flags="0x0">
    <title>Ambient Air Temp Estimate - Flush Minimum Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The flush requirement only runs down while mass airflow is at or above this (stock 5 g/s) and vehicle speed is at or above its minimum. The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it down, and until it reaches zero the estimate can only fall toward the intake air temperature. Effect: raise = more airflow is needed before driving counts toward releasing the ambient estimate Evidence: ledger:E0385, ledger:E0555, ledger:E1...</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x342A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x555" flags="0x0">
    <title>Ambient Air Temp Estimate - Flush Minimum Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The flush requirement only runs down while vehicle speed is at or above this (stock 48.3 km/h = 30 mph) and airflow is at or above its minimum. The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it down, and until it reaches zero the estimate can only fall toward the intake air temperature. Effect: raise = a higher speed is needed before driving counts toward releasing the ambient estimate Evidence: ledger:E0385, ledger:E0555,...</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x342A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x556" flags="0x30">
    <title>Ambient Air Temp Estimate - Flush Rate Weight vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the flush requirement runs down, by mass airflow (0 to 128 g/s): 1.0 takes one second of requirement off per second of qualifying driving, 2.0 two seconds. Stock 1.0 everywhere. The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it down, and until it reaches zero the estimate can only fall toward the intake air temperature. Effect: raise = the ambient estimate is released sooner at that airflow Evidence: ledger:E0385,...</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="8" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="24" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="48" />
      <LABEL index="7" value="56" />
      <LABEL index="8" value="64" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="88" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="104" />
      <LABEL index="14" value="112" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x342AA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x557" flags="0x30">
    <title>EVAP Engine-Off Tank Vacuum Jump Window - Upper</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Change in filtered tank vacuum between updates, by fuel level (0 to 100 %), that is the upper edge of the window that sets the main tank vacuum jump flag during the engine-off test. Stock 32 inH2O in every cell, which is never reached. Effect: lower = the upper edge of the engine-off jump window comes down Evidence: ledger:E0556, ledger:E0899, ledger:E0935, ledger:E0937, ledger:E0940, ledger:E0944, ledger:E1054</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x345F6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>inH2O</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x558" flags="0x30">
    <title>EVAP Engine-Off Tank Vacuum Jump Window - Lower</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Change in filtered tank vacuum between updates, by fuel level (0 to 100 %), that is the lower edge of the window that sets the main tank vacuum jump flag during the engine-off test. Stock 32 inH2O in every cell, which is never reached. Effect: lower = smaller jumps fall inside the engine-off jump window Evidence: ledger:E0556, ledger:E0899, ledger:E0935, ledger:E0937, ledger:E0940, ledger:E0944, ledger:E1054</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3461A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>inH2O</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x559" flags="0x0">
    <title>DFCO - Catalyst Hot Temperature (Short Delay)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or above this catalyst model temperature the short fuel cut delay is used (stock 885 C). Deceleration fuel cut (DFCO): once all the fuel cut conditions hold, fuel is cut only after this delay; the delay restarts whenever the conditions drop out or the gear changes. The catalyst-hot state is set when the catalyst model temperature reaches the hot temperature and lasts until the next fuel cut request. Effect: lower = the short delay is used from a cooler catalyst Evidence: ledger:E0549, ledger:E1382</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2F4CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x55A" flags="0x30">
    <title>Dwell Multiplier vs Cam-Phase Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies coil dwell (base dwell times the voltage and coolant modifier) by the cam-phase factor (Cam-Phase Factor vs Cam Angle and RPM). Ten points from 0 to 0.27 in 0.03 steps; above 0.27 the last point is used. Stock 1.0 everywhere (no effect). Effect: raise = longer coil dwell at that cam-phase factor Evidence: ledger:E0550, ledger:E0884</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>cam-phase factor</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.03" />
      <LABEL index="2" value="0.06" />
      <LABEL index="3" value="0.09" />
      <LABEL index="4" value="0.12" />
      <LABEL index="5" value="0.15" />
      <LABEL index="6" value="0.18" />
      <LABEL index="7" value="0.21" />
      <LABEL index="8" value="0.24" />
      <LABEL index="9" value="0.27" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2FA28" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x55B" flags="0x30">
    <title>Spark Floor vs RPM (alternate mode A)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest spark advance allowed, by rpm, while alternate spark mode A (a run condition set elsewhere in the PCM) is active. Spark below it is raised to it. Stock -15 deg at every rpm. Effect: raise = spark is never allowed below a higher advance Evidence: ledger:E0552, ledger:E0718, ledger:E0724</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x301B0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x55C" flags="0x30">
    <title>Spark Floor vs RPM (alternate mode B)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest spark advance allowed, by rpm, while alternate spark mode B (a run condition set elsewhere in the PCM; mode A takes priority) is active. Spark below it is raised to it. Stock -20 deg at every rpm. Effect: raise = spark is never allowed below a higher advance Evidence: ledger:E0552, ledger:E0718, ledger:E0724</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x301F8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x55D" flags="0x30">
    <title>Spark Floor vs RPM (default)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest spark advance allowed, by rpm, in normal running. Spark below it is raised to it. Stock -15 deg at every rpm. (E0724) Effect: raise = spark is never allowed below a higher advance Evidence: ledger:E0552, ledger:E0718, ledger:E0724</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30168" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x55E" flags="0x30">
    <title>Airflow Transient - Change Threshold vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Diagnostic airflow transient check: a sample counts as transient when the airflow change since the previous sample is at or above this, by airflow (0 to 400 g/s). Stock 10 g/s at idle airflow rising to 30 g/s at 400 g/s. Effect: raise = larger airflow changes needed before a sample counts as transient Evidence: ledger:E0563, ledger:E1269</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>g/s (airflow)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="25" />
      <LABEL index="2" value="50" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="100" />
      <LABEL index="5" value="125" />
      <LABEL index="6" value="150" />
      <LABEL index="7" value="175" />
      <LABEL index="8" value="200" />
      <LABEL index="9" value="225" />
      <LABEL index="10" value="250" />
      <LABEL index="11" value="275" />
      <LABEL index="12" value="300" />
      <LABEL index="13" value="325" />
      <LABEL index="14" value="350" />
      <LABEL index="15" value="375" />
      <LABEL index="16" value="400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x367D6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x55F" flags="0x30">
    <title>MAP Circuit High - Arming Time vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After each start the MAP sensor circuit high monitor (P0108 and P1106) waits this long before it counts samples, by coolant temperature at start. Five points from -30 to 30 C in 15 C steps; outside that range the end points are used. Stock 40 s at -30 C, 30 s at -15 C, 20 s at 0 and 15 C, 5 s at 30 C and above. Effect: raise = the high-circuit monitor starts later after a start Evidence: ledger:E0566, ledger:E0890</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-30" />
      <LABEL index="1" value="-15" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="30" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36856" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x560" flags="0x30">
    <title>MAP Sensor Fault Substitute - Throttle Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the MAP sensor has failed, the PCM uses a modelled manifold pressure instead: the throttle term (throttle area times the throttle curve) plus the engine speed term, capped at 90 kPa. This curve is the throttle term&#x27;s gain by engine speed: kPa of substitute pressure per percent of throttle area. Effect: raise = substitute manifold pressure rises faster with throttle at that engine speed Evidence: ledger:E0166, ledger:E0567, ledger:E0716, ledger:E0839</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>26</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C642" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa per % throttle area</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>20.479375</max>
      <MATH equation="X/3200.0488"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x561" flags="0x30">
    <title>MAP Sensor Fault Substitute - Engine Speed Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the MAP sensor has failed, the PCM uses a modelled manifold pressure instead: the throttle term (throttle area times the throttle curve) plus the engine speed term, capped at 90 kPa. This curve is the engine speed term, added directly. Stock 96 kPa with the engine stopped, falling to 7.5 kPa at higher engine speed. Effect: raise = higher substitute manifold pressure at that engine speed Evidence: ledger:E0166, ledger:E0567, ledger:E0716, ledger:E0839</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>26</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C60C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x562" flags="0x0">
    <title>Airflow Rationality - Intake Air Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101): lowest intake air temperature at which the test runs. Stock -7 C. Effect: raise = the test does not run in colder air Evidence: ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x563" flags="0x0">
    <title>Airflow Rationality - Intake Air Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101): highest intake air temperature at which the test runs. Stock 125 C. Effect: lower = the test stops at a lower intake air temperature Evidence: ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x564" flags="0x0">
    <title>Airflow Rationality - Engine Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101): highest engine speed at which the test runs. Stock 8191.9 rpm (no limit). Effect: lower = the test stops above this engine speed Evidence: ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x565" flags="0x0">
    <title>Airflow Rationality - Intake Manifold Volume</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101), diagnostic model only: intake manifold volume the two manifold pressure models use to turn the difference between air entering and air leaving into a pressure change. Stock 6.4 L. Change only for a different intake manifold. Effect: raise = the modelled manifold pressure changes more slowly Evidence: ledger:E1074</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3670A" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>L</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>268435.455937</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x566" flags="0x0">
    <title>Airflow Rationality - Pressure Difference Filter, Throttle Model</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101): filter on the difference between measured manifold pressure and the pressure modelled from throttle position; each update the filtered difference moves this fraction of the way to the new reading. Stock 0.01 (it takes roughly 100 updates, about 10 s, to follow a change). Effect: raise = the first pressure check reacts faster and is less smoothed Evidence: ledger:E0570, ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3673C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x567" flags="0x0">
    <title>Airflow Rationality - Pressure Difference Filter, Airflow Model</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101): filter on the difference between measured manifold pressure and the pressure modelled from measured airflow; each update the filtered difference moves this fraction of the way to the new reading. Stock 0.01 (it takes roughly 100 updates, about 10 s, to follow a change). Effect: raise = the second pressure check reacts faster and is less smoothed Evidence: ledger:E0570, ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3673E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x568" flags="0x0">
    <title>Catalyst Monitor - Idle RPM Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: engine speed below this counts as idle; time spent at or above it counts as driving. Stock 950 rpm. Effect: raise = higher engine speeds still count as idle Evidence: ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x569" flags="0x0">
    <title>Catalyst Monitor Enable - Off Idle Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: an idle period only qualifies for a test if the engine spent at least this long off idle just before it. Stock 35 s. Effect: lower = a shorter drive between idle periods is enough Evidence: ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x56A" flags="0x0">
    <title>Catalyst Monitor Enable - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: an idle period only qualifies once the engine has been running at least this long. Stock 600 s. Effect: lower = the test can run sooner after a start Evidence: ledger:E0814, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x56B" flags="0x0">
    <title>Catalyst Monitor Enable - Stopped Time Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only arms while the vehicle has been stopped with the throttle closed for no longer than this. Stock 60 s. Effect: raise = the test can still arm later into a stop Evidence: ledger:E0999</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x56C" flags="0x0">
    <title>Catalyst Monitor Enable - Intake Air Temperature Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only arms while intake air temperature is below this. Stock 80 C. Effect: lower = the test stops arming at a lower intake air temperature Evidence: ledger:E0572, ledger:E0984, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x56D" flags="0x30">
    <title>PE / COT Spark Correction Factor vs MAP</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Power enrichment / catalyst over-temperature spark correction: the correction from the PE / COT Spark Advance Correction table is multiplied by this factor by manifold pressure (20 to 100 kPa) while power enrichment or catalyst protection is active. Stock 1.0 at every pressure (the full correction). Effect: lower = less of the PE / COT spark correction is applied at that manifold pressure Evidence: ledger:E0577, ledger:E1257</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="20" />
      <LABEL index="1" value="25" />
      <LABEL index="2" value="30" />
      <LABEL index="3" value="35" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="45" />
      <LABEL index="6" value="50" />
      <LABEL index="7" value="55" />
      <LABEL index="8" value="60" />
      <LABEL index="9" value="65" />
      <LABEL index="10" value="70" />
      <LABEL index="11" value="75" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="85" />
      <LABEL index="14" value="90" />
      <LABEL index="15" value="95" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2DCB2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x56E" flags="0x0">
    <title>P0116 Test Enable - Engine Off Soak Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116): only runs after the engine has been off for longer than this. Stock 28800 s (8 hours). Effect: lower = the test also runs after a shorter soak Evidence: ledger:E1011</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33722" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x56F" flags="0x0">
    <title>P0125 / P0128 Check - Intake Air Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: the checks are skipped for the trip once the lowest intake air temperature seen since start is below this. Stock -6.75 degC. Effect: lower = the checks also run in colder weather Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3372E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x570" flags="0x0">
    <title>P0125 / P0128 Check - Engine Run Time Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: an instance that has not started by this engine run time is skipped for the trip. Stock 1800 s. Effect: raise = the checks may still start later in the trip Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3372A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x571" flags="0x0">
    <title>P0125 / P0128 Check - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: the checks become active once the engine has run this long. Stock 30 s. Effect: raise = the checks become active later Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3372C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x572" flags="0x0">
    <title>P0125 / P0128 Check - Distance Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: the distance they require only counts while vehicle speed is at or above this. Stock 3 km/h. Effect: raise = slow driving no longer counts toward the distance Evidence: ledger:E0582, ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33732" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x573" flags="0x0">
    <title>Idle Gate - Accumulated Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the idle monitor gate&#x27;s timer must accumulate before it completes and sets its done flag (stock 2.0 s). The timer only runs while the gate&#x27;s start conditions hold. Effect: raise = the gate needs longer before it completes Evidence: ledger:E0307, ledger:E0584, ledger:E1438</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3346C" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x574" flags="0x30">
    <title>Idle Speed Control Acquire - Integral Step vs RPM Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: size of each step of the airflow integral while the controller is catching the idle speed (one step every 25 ms on stock), by rpm error (idle reference minus engine speed, -160 to +160 rpm; positive = engine below the reference). The step goes up when the engine is below the reference and down when above. Effect: raise = the integral moves faster at that rpm error Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm error</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-160" />
      <LABEL index="1" value="-140" />
      <LABEL index="2" value="-120" />
      <LABEL index="3" value="-100" />
      <LABEL index="4" value="-80" />
      <LABEL index="5" value="-60" />
      <LABEL index="6" value="-40" />
      <LABEL index="7" value="-20" />
      <LABEL index="8" value="0" />
      <LABEL index="9" value="20" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="60" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="100" />
      <LABEL index="14" value="120" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22362" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x575" flags="0x30">
    <title>Idle Speed Control Acquire - Proportional Gain vs RPM Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: proportional airflow per rpm of error while the controller is catching the idle speed, by rpm error (idle reference minus engine speed, -160 to +160 rpm; positive = engine below the reference). On stock it has no effect: the acquire proportional limits are both 0. Effect: raise = more airflow per rpm of error (only once the acquire proportional limits are opened) Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm error</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-160" />
      <LABEL index="1" value="-140" />
      <LABEL index="2" value="-120" />
      <LABEL index="3" value="-100" />
      <LABEL index="4" value="-80" />
      <LABEL index="5" value="-60" />
      <LABEL index="6" value="-40" />
      <LABEL index="7" value="-20" />
      <LABEL index="8" value="0" />
      <LABEL index="9" value="20" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="60" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="100" />
      <LABEL index="14" value="120" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22386" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s per rpm</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x576" flags="0x30">
    <title>Idle Speed Control - Integral Step vs RPM Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: size of each step of the airflow integral in steady closed loop idle control (one step every 16 passes = 0.4 s on stock), by rpm error (idle reference minus engine speed, -160 to +160 rpm; positive = engine below the reference). The step goes up when the engine is below the reference and down when above. Effect: raise = the integral moves faster at that rpm error Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm error</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-160" />
      <LABEL index="1" value="-140" />
      <LABEL index="2" value="-120" />
      <LABEL index="3" value="-100" />
      <LABEL index="4" value="-80" />
      <LABEL index="5" value="-60" />
      <LABEL index="6" value="-40" />
      <LABEL index="7" value="-20" />
      <LABEL index="8" value="0" />
      <LABEL index="9" value="20" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="60" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="100" />
      <LABEL index="14" value="120" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x223B2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x577" flags="0x30">
    <title>Idle Speed Control - Proportional Gain vs RPM Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: proportional airflow per rpm of error in steady closed loop idle control, by rpm error (idle reference minus engine speed, -160 to +160 rpm; positive = engine below the reference). The result is limited by the proportional maximum / minimum. Effect: raise = more airflow per rpm of error Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm error</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-160" />
      <LABEL index="1" value="-140" />
      <LABEL index="2" value="-120" />
      <LABEL index="3" value="-100" />
      <LABEL index="4" value="-80" />
      <LABEL index="5" value="-60" />
      <LABEL index="6" value="-40" />
      <LABEL index="7" value="-20" />
      <LABEL index="8" value="0" />
      <LABEL index="9" value="20" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="60" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="100" />
      <LABEL index="14" value="120" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x223D6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s per rpm</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x578" flags="0x0">
    <title>Idle Speed Control - Proportional Maximum, Control</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: largest airflow the proportional term may add while holding idle. Stock 0.5 g/s. Effect: raise = the proportional term may add more air at idle Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x223F8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x579" flags="0x0">
    <title>Idle Speed Control - Proportional Minimum, Control</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: most airflow the proportional term may remove while holding idle. Stock -0.5 g/s. Effect: lower = the proportional term may remove more air at idle Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x223FA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x57A" flags="0x0">
    <title>Diagnostic Model - Engine Speed Input Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Diagnostic model: three channels that rise toward a target set by engine speed and airflow and fall back when they drop, with a fixed value while coolant is cold. Its only readers are the misfire monitor enable conditions, a diagnostic timer and the secondary air routine; it does not limit torque, spark, fuel or throttle. Engine speed above this counts as this speed. Changing it moves when the misfire monitor runs. Stock 4000 rpm. Effect: moves when the misfire monitor and related diagnostics are enabled Evidence: ledger:E0588, ledger:E0852</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337DC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x57B" flags="0x0">
    <title>Diagnostic Model - Airflow Input Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Diagnostic model: three channels that rise toward a target set by engine speed and airflow and fall back when they drop, with a fixed value while coolant is cold. Its only readers are the misfire monitor enable conditions, a diagnostic timer and the secondary air routine; it does not limit torque, spark, fuel or throttle. Airflow above this counts as this airflow. Changing it moves when the misfire monitor runs. Stock 50 g/s. Effect: moves when the misfire monitor and related diagnostics are enabled Evidence: ledger:E0588, ledger:E0852</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337DE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x57C" flags="0x0">
    <title>Idle Area Command - Value at Full Throttle Area</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle airflow area command value that corresponds to full throttle area: the requested idle throttle area is the command divided by this (then limited by Idle Throttle Area Maximum). Stock 100 %, so a command of 2 % requests 2 % of full throttle area. Effect: raise = the same idle command opens the throttle less Evidence: ledger:E0589, ledger:E1445</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x24CD6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>182.041667</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/360"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x57D" flags="0x0">
    <title>Idle Throttle Area Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle airflow control&#x27;s throttle area request is capped at this percentage of full throttle area. Stock 2.82 %. Effect: raise = the idle control can open the throttle further Evidence: ledger:E0282, ledger:E0589, ledger:E0924</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x24C72" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x57E" flags="0x0">
    <title>Traction Control - Throttle Area Raise Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While traction control is cutting fuel, the throttle area may be raised to the traction control request, but no higher than this. Stock 2.82 %. The traction control fuel cut is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0590, ledger:E1198, ledger:E1199</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x24CD4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x57F" flags="0x30">
    <title>Throttle Area Limit vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Ceiling on the commanded throttle area (percent of full area) by engine speed (0 to 8192 rpm), multiplied by the intake air and barometric pressure factors. Stock 100 % (no limit). Effect: lower = caps the commanded throttle area at that engine speed Evidence: ledger:E0452, ledger:E0590, ledger:E1198</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24C7A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle area</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x580" flags="0x30">
    <title>Throttle Area Limit Factor vs Intake Air Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the throttle area limit by engine speed, by intake air temperature (-40 to 152 C). 1.0 = no change. Stock 1.0 everywhere. Effect: lower = lowers the throttle area limit in that condition Evidence: ledger:E0591, ledger:E1197, ledger:E1198</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (intake air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24CC2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x581" flags="0x30">
    <title>Throttle Area Limit Factor vs Barometric Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the throttle area limit by engine speed, by barometric pressure (60 to 105 kPa). 1.0 = no change. Stock 1.0 everywhere. Effect: lower = lowers the throttle area limit in that condition Evidence: ledger:E0591, ledger:E1197, ledger:E1198</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (barometric pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="60" />
      <LABEL index="1" value="62.812" />
      <LABEL index="2" value="65.625" />
      <LABEL index="3" value="68.438" />
      <LABEL index="4" value="71.25" />
      <LABEL index="5" value="74.062" />
      <LABEL index="6" value="76.875" />
      <LABEL index="7" value="79.688" />
      <LABEL index="8" value="82.5" />
      <LABEL index="9" value="85.312" />
      <LABEL index="10" value="88.125" />
      <LABEL index="11" value="90.938" />
      <LABEL index="12" value="93.75" />
      <LABEL index="13" value="96.562" />
      <LABEL index="14" value="99.375" />
      <LABEL index="15" value="102.188" />
      <LABEL index="16" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24C9E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x582" flags="0x30">
    <title>Pedal Throttle Request Factor vs Cam-Phase Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the driver&#x27;s pedal throttle request, by the cam-phase factor (0 to 0.5; the Cam-Phase Factor vs Cam Angle and RPM table, stock up to 0.24). The PCM multiplies the pedal map&#x27;s throttle request by this and several other factors. 1.0 = no change; lower = less throttle for the same pedal. Stock 1.0 everywhere. Effect: lower = less throttle for the same pedal when the cam-phase factor is at that value Evidence: ledger:E0594, ledger:E0881, ledger:E0947, ledger:E1195</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>cam-phase factor (fraction)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.031" />
      <LABEL index="2" value="0.062" />
      <LABEL index="3" value="0.094" />
      <LABEL index="4" value="0.125" />
      <LABEL index="5" value="0.156" />
      <LABEL index="6" value="0.188" />
      <LABEL index="7" value="0.219" />
      <LABEL index="8" value="0.25" />
      <LABEL index="9" value="0.281" />
      <LABEL index="10" value="0.312" />
      <LABEL index="11" value="0.344" />
      <LABEL index="12" value="0.375" />
      <LABEL index="13" value="0.406" />
      <LABEL index="14" value="0.438" />
      <LABEL index="15" value="0.469" />
      <LABEL index="16" value="0.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23F18" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x583" flags="0x30">
    <title>Pedal Throttle Request Factor vs Commanded Air-Fuel Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the driver&#x27;s pedal throttle request, by the commanded air-fuel ratio (0 to 32). The PCM multiplies the pedal map&#x27;s throttle request by this and several other factors. 1.0 = no change; lower = less throttle for the same pedal. Stock 1.0 everywhere. Effect: lower = less throttle for the same pedal position Evidence: ledger:E0594, ledger:E0947</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>AFR (commanded)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="4" />
      <LABEL index="3" value="6" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="12" />
      <LABEL index="7" value="14" />
      <LABEL index="8" value="16" />
      <LABEL index="9" value="18" />
      <LABEL index="10" value="20" />
      <LABEL index="11" value="22" />
      <LABEL index="12" value="24" />
      <LABEL index="13" value="26" />
      <LABEL index="14" value="28" />
      <LABEL index="15" value="30" />
      <LABEL index="16" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23F3C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x584" flags="0x30">
    <title>Pedal Throttle Request Factor vs Torque Reduction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the driver&#x27;s pedal throttle request, by how much of the engine torque is being removed (0 to 50 %). The PCM multiplies the pedal map&#x27;s throttle request by this and several other factors. 1.0 = no change; lower = less throttle for the same pedal. Stock 1.0 everywhere. Effect: lower = less throttle for the same pedal position Evidence: ledger:E0594, ledger:E0947</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% torque reduction</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="3.125" />
      <LABEL index="2" value="6.25" />
      <LABEL index="3" value="9.375" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="15.625" />
      <LABEL index="6" value="18.75" />
      <LABEL index="7" value="21.875" />
      <LABEL index="8" value="25" />
      <LABEL index="9" value="28.125" />
      <LABEL index="10" value="31.25" />
      <LABEL index="11" value="34.375" />
      <LABEL index="12" value="37.5" />
      <LABEL index="13" value="40.625" />
      <LABEL index="14" value="43.75" />
      <LABEL index="15" value="46.875" />
      <LABEL index="16" value="50" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23F72" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x585" flags="0x30">
    <title>Pedal Throttle Request Factor vs Barometric Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the driver&#x27;s pedal throttle request, by barometric pressure (60 to 105 kPa). The PCM multiplies the pedal map&#x27;s throttle request by this and several other factors. 1.0 = no change; lower = less throttle for the same pedal. Stock 1.0 everywhere. Effect: lower = less throttle for the same pedal at that barometric pressure Evidence: ledger:E0595, ledger:E0947, ledger:E1197</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (barometric pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="60" />
      <LABEL index="1" value="62.812" />
      <LABEL index="2" value="65.625" />
      <LABEL index="3" value="68.438" />
      <LABEL index="4" value="71.25" />
      <LABEL index="5" value="74.062" />
      <LABEL index="6" value="76.875" />
      <LABEL index="7" value="79.688" />
      <LABEL index="8" value="82.5" />
      <LABEL index="9" value="85.312" />
      <LABEL index="10" value="88.125" />
      <LABEL index="11" value="90.938" />
      <LABEL index="12" value="93.75" />
      <LABEL index="13" value="96.562" />
      <LABEL index="14" value="99.375" />
      <LABEL index="15" value="102.188" />
      <LABEL index="16" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23EF4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x586" flags="0x30">
    <title>Pedal Gain Reduction - Request Factor Cut vs Pedal</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Amount taken off the pedal throttle request factor when the pedal gain reduction starts, by pedal position (0 to 100 %). The cut is applied once per event and the factor is not cut below the Request Factor Floor. Stock 0 everywhere, and the floor is 1.0, so the reduction cuts nothing on the stock file. Effect: raise = the pedal gain reduction cuts the pedal request more at that pedal position Evidence: ledger:E0596, ledger:E1118, ledger:E1206</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23F96" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x587" flags="0x30">
    <title>Pedal Gain Increase vs Launch Acceleration Shortfall</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal gain increase target by how far the launch fell short of the pedal gain reduction acceleration threshold (threshold divided by measured acceleration, averaged over the samples: 1.0 = on the threshold, 2.0 = half of it). Values below 1.0 count as 1.0. The result is filtered, weighted by the Speed Weight and capped by the Pedal Request Factor Ceiling. Stock 1.0 everywhere, and the learn does not run on stock. Effect: raise = more pedal gain when the truck launches slower than the acceleration threshold Evidence: ledger:E0597, ledger:E1203, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>threshold / measured acceleration</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.5" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="1.5" />
      <LABEL index="4" value="2" />
      <LABEL index="5" value="2.5" />
      <LABEL index="6" value="3" />
      <LABEL index="7" value="3.5" />
      <LABEL index="8" value="4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23FCE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x588" flags="0x30">
    <title>Pedal Gain Increase - Speed Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the pedal gain increase (the amount the pedal gain is raised above 1.0) that is applied, by vehicle speed (0 to 64 km/h). Stock 1.0 (all of it). The increase itself is 1.0 everywhere in the stock calibration, so this has no effect until the increase is raised. Effect: lower = less of the pedal gain increase is used at that vehicle speed Evidence: ledger:E0597, ledger:E1195, ledger:E1200</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23FE6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x589" flags="0x30">
    <title>Pedal Response Change - Wide Open Vacuum Threshold vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal response changes (pedal map selection and any raise of the pedal request factor) are only taken while the pedal is at rest or wide open. Above the Wide Open Pedal Threshold, the pedal counts as wide open while manifold vacuum is below this value at the current engine speed. Stock 10.0 kPa at all speeds. Effect: raise = the pedal counts as wide open at a higher manifold vacuum at that rpm Evidence: ledger:E0598, ledger:E0792, ledger:E0805, ledger:E1209</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24B4E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x58A" flags="0x0">
    <title>Fuel Level Filter Start Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the PCM waits after the fuel level filter is reset before it starts filtering fuel level, and with it the fuel level jump check the EVAP leak test uses. Stock 1.0 s. Effect: raise = fuel level filtering and the EVAP fuel level jump check start later Evidence: ledger:E0217, ledger:E0599, ledger:E0942</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35778" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x58B" flags="0x0">
    <title>EVAP Vapour Reference at Full Tank</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP test vapour reference with a full tank. The PCM blends linearly from this value (full) to the empty-tank value by fuel level, and the EVAP leak test tables are looked up by the result, so this sets which rows of those tables apply at each fuel level. Stock 3003. Shown raw. DO NOT EDIT. Effect: raise = the blended result starts higher; lower = it starts lower Evidence: ledger:E0599, ledger:E0899, ledger:E0941, ledger:E0944</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35780" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x58C" flags="0x0">
    <title>EVAP Vapour Reference at Empty Tank</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP test vapour reference with an empty tank. The PCM blends linearly from the full-tank value to this value (empty) by fuel level, and the EVAP leak test tables are looked up by the result, so this sets which rows of those tables apply at each fuel level. Stock 25582. Shown raw. DO NOT EDIT. Effect: raise = the blended result can reach higher; lower = it is capped lower Evidence: ledger:E0599, ledger:E0899, ledger:E0941, ledger:E0944</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3577A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x58D" flags="0x30">
    <title>EVAP Test Fuel Level Jump Limit A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest change in filtered fuel level between updates that the EVAP leak test tolerates, by fuel level. A bigger jump (either direction) sets a fuel level jump flag, and the EVAP leak test routines pause or restart while it is set. Stock 100 % everywhere, so the flag never sets. Effect: lower = smaller fuel level jumps pause or restart the EVAP leak test Evidence: ledger:E0600, ledger:E0935</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35732" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% fuel level change</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x58E" flags="0x30">
    <title>EVAP Test Fuel Level Jump Limit B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest change in filtered fuel level between updates that the EVAP leak test tolerates, by fuel level. A bigger jump (either direction) sets a fuel level jump flag, and the EVAP leak test routines pause or restart while it is set. Stock 100 % everywhere, so the flag never sets. Effect: lower = smaller fuel level jumps pause or restart the EVAP leak test Evidence: ledger:E0600, ledger:E0935</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35756" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% fuel level change</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x58F" flags="0x30">
    <title>EVAP Test Vehicle Speed Drop Limit A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest vehicle speed drop between updates that the EVAP leak test tolerates, by vehicle speed. A bigger drop sets a speed jump flag and the leak test restarts its count. Stock -100 km/h per update, so it never acts. Effect: raise (toward 0) = smaller speed drops pause or restart the EVAP leak test Evidence: ledger:E0601, ledger:E0734, ledger:E0935, ledger:E1217</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (vehicle speed x128)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <LABEL index="11" value="110" />
      <LABEL index="12" value="120" />
      <LABEL index="13" value="130" />
      <LABEL index="14" value="140" />
      <LABEL index="15" value="150" />
      <LABEL index="16" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35784" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per update</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x590" flags="0x30">
    <title>EVAP Test Vehicle Speed Drop Limit B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest vehicle speed drop between updates that the EVAP leak test tolerates, by vehicle speed. Checked only past Limit A: a drop beyond this holds the leak test steps and its purge flow count instead. Stock -100 km/h per update, so it never acts. Effect: raise (toward 0) = smaller speed drops hold off the EVAP leak test Evidence: ledger:E0601, ledger:E0734, ledger:E0935, ledger:E1217</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (vehicle speed x128)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <LABEL index="11" value="110" />
      <LABEL index="12" value="120" />
      <LABEL index="13" value="130" />
      <LABEL index="14" value="140" />
      <LABEL index="15" value="150" />
      <LABEL index="16" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x357F0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per update</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x591" flags="0x30">
    <title>EVAP Test Vehicle Speed Rise Limit A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest vehicle speed rise between updates that the EVAP leak test tolerates, by vehicle speed. A bigger rise sets a speed jump flag and the leak test restarts its count. Stock +100 km/h per update, so it never acts. Effect: lower = smaller speed rises pause or restart the EVAP leak test Evidence: ledger:E0601, ledger:E0734, ledger:E0935, ledger:E1217</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (vehicle speed x128)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <LABEL index="11" value="110" />
      <LABEL index="12" value="120" />
      <LABEL index="13" value="130" />
      <LABEL index="14" value="140" />
      <LABEL index="15" value="150" />
      <LABEL index="16" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x357A8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per update</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x592" flags="0x30">
    <title>EVAP Test Vehicle Speed Rise Limit B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest vehicle speed rise between updates that the EVAP leak test tolerates, by vehicle speed. Checked only past Limit A: a rise beyond this holds the leak test steps and its purge flow count instead. Stock +100 km/h per update, so it never acts. Effect: lower = smaller speed rises hold off the EVAP leak test Evidence: ledger:E0601, ledger:E0734, ledger:E0935, ledger:E1217</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (vehicle speed x128)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <LABEL index="11" value="110" />
      <LABEL index="12" value="120" />
      <LABEL index="13" value="130" />
      <LABEL index="14" value="140" />
      <LABEL index="15" value="150" />
      <LABEL index="16" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x357CC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per update</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x593" flags="0x0">
    <title>P0496 Pass - Time, Cold Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve leak check (P0496): time with purge off without the vacuum limit being exceeded that passes the check, cold start. Stock 60 s. Effect: raise = the check runs longer before it passes Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35852" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x594" flags="0x30">
    <title>EVAP Leak Test Settle Time Limit - Low Range</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP leak test, before the vacuum hold is timed: while tank vacuum is still above the settle level, the PCM waits up to this long before it takes the starting vacuum reading, then starts timing the decay. The axis covers the lower half of the EVAP test reference value (the EVAP vapour reference, which the PCM derives from fuel level: the axis labels give the fuel level on stock settings, n/a = not reached). Stock 40 s everywhere. Not used by the stock calibration: this belongs to the engine-running small leak phase, which the stock calibration switches off (small leaks are checked by the engine-off test instead). Effect: no e...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>% fuel level (stock settings)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="n/a" />
      <LABEL index="1" value="n/a" />
      <LABEL index="2" value="n/a" />
      <LABEL index="3" value="100" />
      <LABEL index="4" value="95" />
      <LABEL index="5" value="91" />
      <LABEL index="6" value="86" />
      <LABEL index="7" value="82" />
      <LABEL index="8" value="77" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="68" />
      <LABEL index="11" value="63" />
      <LABEL index="12" value="59" />
      <LABEL index="13" value="54" />
      <LABEL index="14" value="50" />
      <LABEL index="15" value="45" />
      <LABEL index="16" value="41" />
      <LABEL index="17" value="36" />
      <LABEL index="18" value="32" />
      <LABEL index="19" value="27" />
      <LABEL index="20" value="23" />
      <LABEL index="21" value="18" />
      <LABEL index="22" value="14" />
      <LABEL index="23" value="9" />
      <LABEL index="24" value="4" />
      <LABEL index="25" value="0" />
      <LABEL index="26" value="n/a" />
      <LABEL index="27" value="n/a" />
      <LABEL index="28" value="n/a" />
      <LABEL index="29" value="n/a" />
      <LABEL index="30" value="n/a" />
      <LABEL index="31" value="n/a" />
      <LABEL index="32" value="n/a" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35D48" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x595" flags="0x30">
    <title>EVAP Leak Test Settle Time Limit - High Range</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP leak test, before the vacuum hold is timed: while tank vacuum is still above the settle level, the PCM waits up to this long before it takes the starting vacuum reading, then starts timing the decay. The axis covers the upper half of the EVAP test reference value (the EVAP vapour reference; with stock settings it never reaches this range, so this curve is not used). Stock 40 s everywhere. Not used by the stock calibration: this belongs to the engine-running small leak phase, which the stock calibration switches off (small leaks are checked by the engine-off test instead). Effect: no effect in the stock calibration Eviden...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>% fuel level (stock settings)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="n/a" />
      <LABEL index="1" value="n/a" />
      <LABEL index="2" value="n/a" />
      <LABEL index="3" value="n/a" />
      <LABEL index="4" value="n/a" />
      <LABEL index="5" value="n/a" />
      <LABEL index="6" value="n/a" />
      <LABEL index="7" value="n/a" />
      <LABEL index="8" value="n/a" />
      <LABEL index="9" value="n/a" />
      <LABEL index="10" value="n/a" />
      <LABEL index="11" value="n/a" />
      <LABEL index="12" value="n/a" />
      <LABEL index="13" value="n/a" />
      <LABEL index="14" value="n/a" />
      <LABEL index="15" value="n/a" />
      <LABEL index="16" value="n/a" />
      <LABEL index="17" value="n/a" />
      <LABEL index="18" value="n/a" />
      <LABEL index="19" value="n/a" />
      <LABEL index="20" value="n/a" />
      <LABEL index="21" value="n/a" />
      <LABEL index="22" value="n/a" />
      <LABEL index="23" value="n/a" />
      <LABEL index="24" value="n/a" />
      <LABEL index="25" value="n/a" />
      <LABEL index="26" value="n/a" />
      <LABEL index="27" value="n/a" />
      <LABEL index="28" value="n/a" />
      <LABEL index="29" value="n/a" />
      <LABEL index="30" value="n/a" />
      <LABEL index="31" value="n/a" />
      <LABEL index="32" value="n/a" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35D90" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x596" flags="0x0">
    <title>EVAP Test - Purge Step per Update</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test: largest change of commanded purge per 100 ms while the test controls purge (pull-down and ramp down). Stock 1 %. Effect: raise = purge changes faster during the test Evidence: ledger:E0605, ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35870" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x597" flags="0x30">
    <title>EVAP Test Vacuum Pull-Down - Proportional Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Purge valve opening added per inH2O that the tank vacuum is short of the test vacuum. Stock 0 at the first point, then 8.6 rising to 20.4 % per inH2O; about 15.5 at the fixed stock reference. Used by the EVAP leak test while it pulls the tank down to its test vacuum; the purge valve is driven by this controller instead of the normal purge command (rate limited around it). Effect: raise = faster, more aggressive pull-down (more overshoot) Evidence: ledger:E0606, ledger:E1488</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>EVAP test vapour reference (raw)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1600" />
      <LABEL index="3" value="2400" />
      <LABEL index="4" value="3200" />
      <LABEL index="5" value="4000" />
      <LABEL index="6" value="4800" />
      <LABEL index="7" value="5600" />
      <LABEL index="8" value="6400" />
      <LABEL index="9" value="7200" />
      <LABEL index="10" value="8000" />
      <LABEL index="11" value="8800" />
      <LABEL index="12" value="9600" />
      <LABEL index="13" value="10400" />
      <LABEL index="14" value="11200" />
      <LABEL index="15" value="12000" />
      <LABEL index="16" value="12800" />
      <LABEL index="17" value="13600" />
      <LABEL index="18" value="14400" />
      <LABEL index="19" value="15200" />
      <LABEL index="20" value="16000" />
      <LABEL index="21" value="16800" />
      <LABEL index="22" value="17600" />
      <LABEL index="23" value="18400" />
      <LABEL index="24" value="19200" />
      <LABEL index="25" value="20000" />
      <LABEL index="26" value="20800" />
      <LABEL index="27" value="21600" />
      <LABEL index="28" value="22400" />
      <LABEL index="29" value="23200" />
      <LABEL index="30" value="24000" />
      <LABEL index="31" value="24800" />
      <LABEL index="32" value="25600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35DD8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%/inH2O</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>64.250000</max>
      <MATH equation="X/1020"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x598" flags="0x30">
    <title>EVAP Test Vacuum Pull-Down - Integral Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Purge valve opening added per second for each inH2O that the tank vacuum is short of the test vacuum. Stock 0 at the first point, then 2.7 rising to 6.4 % per inH2O per second; about 4.9 at the fixed stock reference. Used by the EVAP leak test while it pulls the tank down to its test vacuum; the purge valve is driven by this controller instead of the normal purge command (rate limited around it). Effect: raise = the remaining vacuum error is closed faster Evidence: ledger:E0606, ledger:E1488</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>EVAP test vapour reference (raw)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1600" />
      <LABEL index="3" value="2400" />
      <LABEL index="4" value="3200" />
      <LABEL index="5" value="4000" />
      <LABEL index="6" value="4800" />
      <LABEL index="7" value="5600" />
      <LABEL index="8" value="6400" />
      <LABEL index="9" value="7200" />
      <LABEL index="10" value="8000" />
      <LABEL index="11" value="8800" />
      <LABEL index="12" value="9600" />
      <LABEL index="13" value="10400" />
      <LABEL index="14" value="11200" />
      <LABEL index="15" value="12000" />
      <LABEL index="16" value="12800" />
      <LABEL index="17" value="13600" />
      <LABEL index="18" value="14400" />
      <LABEL index="19" value="15200" />
      <LABEL index="20" value="16000" />
      <LABEL index="21" value="16800" />
      <LABEL index="22" value="17600" />
      <LABEL index="23" value="18400" />
      <LABEL index="24" value="19200" />
      <LABEL index="25" value="20000" />
      <LABEL index="26" value="20800" />
      <LABEL index="27" value="21600" />
      <LABEL index="28" value="22400" />
      <LABEL index="29" value="23200" />
      <LABEL index="30" value="24000" />
      <LABEL index="31" value="24800" />
      <LABEL index="32" value="25600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35E20" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%/inH2O/s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>128.500000</max>
      <MATH equation="X/510"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x599" flags="0x0">
    <title>Diagnostic Result Gate - Time Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A diagnostic check compares its own timer with this when it chooses its result (the trouble code it reports and its pass / fail flag). Stock 6.0 s. Effect: raise = the check waits longer before its result Evidence: ledger:E0607, ledger:E1265</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20846" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x59A" flags="0x30">
    <title>Warm-Up Time vs Startup Coolant Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum engine run time by start-up coolant temperature (-40 to 140 C in 20 C steps); the warm-up flag is set while run time is below it. Stock 5, 4, 3, 2 s at -40, -20, 0, 20 C, then 1 s. Effect: raise = the warm-up gate stays true longer at that coolant temperature Evidence: ledger:E0609, ledger:E1184</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <LABEL index="9" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28FA6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x59B" flags="0x0">
    <title>Tip-In Torque Ramp - Fast Step Vehicle Speed Trigger</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. After a shunt and swing back, the fast step also starts once vehicle speed rises faster than this per update. Stock 60 km/h per update (effectively off). Effect: tip-in torque management Evidence: ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21534" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h per update</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x59C" flags="0x30">
    <title>Starter - Cut-Out RPM vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM treats the engine as started, and turns the starter relay off, once engine speed has stayed above this for a short confirmation count, by coolant temperature. Stock 550 rpm at -40 C falling to 400 rpm from 56 C. Effect: raise = the starter stays engaged to a higher engine speed Evidence: ledger:E1024, ledger:E1288</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x302BE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x59D" flags="0x30">
    <title>Starter - Cut-Out Confirmation Revolutions vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The engine counts as started, and the starter is released, once it has turned more than this many revolutions above the starter cut-out engine speed, by coolant temperature. Stock 2 at -40 to -16 C, 1 above. Effect: raise = the engine must turn more revolutions above the cut-out speed before it counts as started Evidence: ledger:E0617, ledger:E1185</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x302E8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>crank revolutions</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x59E" flags="0x30">
    <title>Starter Low-Voltage Hold - Hold Time vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter low-voltage hold: the hold ends this long after the starter engaged, by coolant temperature at start-up; after that the normal key and crank time rules apply again. Stock 4.5 s at -30 C to 1.5 s from 7.5 C. Effect: raise = the starter is held longer through a voltage collapse Evidence: ledger:E0618, ledger:E1025, ledger:E1288</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-30" />
      <LABEL index="1" value="-17.5" />
      <LABEL index="2" value="-5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="20" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x302AA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x59F" flags="0x30">
    <title>Starter Low-Voltage Hold - Arm Time vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter low-voltage hold: if system voltage collapses below 4 V while cranking, the PCM keeps the starter engaged without the key signal. That can only begin once the starter has been engaged for this long. Stock 0.2 s. Effect: raise = the starter must be engaged longer before the hold can begin Evidence: ledger:E0619, ledger:E1025, ledger:E1288</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-30" />
      <LABEL index="1" value="-17.5" />
      <LABEL index="2" value="-5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="20" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3029A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5A0" flags="0x0">
    <title>Vehicle Bus - Oil Life Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum time between two sends of the oil life message. Stock 1.0 s. Vehicle bus (serial data to the other modules): the message is sent again once at least the minimum interval has passed since it was last sent and the value has changed by at least the change threshold (or a status in it changed). Effect: lower = sent more often Evidence: ledger:E0626, ledger:E0801, ledger:E0805, ledger:E1676</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20296" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5A1" flags="0x30">
    <title>Long Soak Start - Minimum Engine-Off Time vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum time the engine must have been off, by corrected coolant temperature at power-up, for the start to count as a long-soak start (stock 30 s at minus 40 C, 20 s from 8 C up). Checked once per power-up while the soak timer is valid; the counted starts set a status flag that other diagnostics check. Effect: raise = a longer engine-off time is needed before a start counts Evidence: ledger:E0221, ledger:E0254, ledger:E0629, ledger:E1455</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2312A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5A2" flags="0x0">
    <title>Cam Phasing Alt Mode Deactivate Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at or below which an alternate cam phasing control mode is switched off once it has been active (further conditions must also hold for it to stay on above this speed). Stock value is above the engine&#x27;s redline, so this mode is not reached in normal driving. Effect: raise = the mode has to run at a higher engine speed before it can be switched off Evidence: ledger:E0630</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22CBE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5A3" flags="0x0">
    <title>Cam Phasing Alt Mode Activate Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed that an alternate cam phasing control mode must reach, along with other conditions, before it can switch on. Stock value is above the engine&#x27;s redline, so this mode does not activate in normal driving. Effect: raise = a higher engine speed is required before the mode can switch on Evidence: ledger:E0630</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22CC0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5A4" flags="0x0">
    <title>Idle Speed Control - Integral Dead Band</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: the integral term does not step while the average idle speed error is at or below this. Stock 5 rpm. Effect: raise = the controller tolerates a larger steady idle speed error Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2235A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5A5" flags="0x30">
    <title>Idle Speed Control Acquire - Airflow Request Floor With Throttle Sensor Fault</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: lowest total airflow request while the controller is catching the idle speed and a throttle position sensor fault is present (P0120 with P0220, or P2135), by barometric pressure (61 to 99 kPa). Stock 3.5 g/s everywhere. Effect: raise = more idle airflow in that fault mode Evidence: ledger:E1108</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>kPa baro</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="61" />
      <LABEL index="1" value="70.5" />
      <LABEL index="2" value="80" />
      <LABEL index="3" value="89.5" />
      <LABEL index="4" value="99" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2275E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5A6" flags="0x30">
    <title>Idle Speed Control Acquire - Airflow Request Floor vs Barometric Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: lowest total airflow request while the controller is catching the idle speed, by barometric pressure (61 to 99 kPa). Stock -10 g/s everywhere: no floor. Effect: raise = the request cannot fall below this while catching idle Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>kPa baro</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="61" />
      <LABEL index="1" value="70.5" />
      <LABEL index="2" value="80" />
      <LABEL index="3" value="89.5" />
      <LABEL index="4" value="99" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22752" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5A7" flags="0x30">
    <title>Idle A/C Turn-On Airflow vs Intake Air Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra idle airflow added when the A/C compressor turns on, by intake air temperature (-30 to 130 C). It is added to the A/C pressure term, held for the A/C turn-on hold time, then removed by the A/C hold airflow decay step. Stock 0 at every temperature. Effect: raise = more extra idle airflow when the A/C compressor turns on at that intake temperature Evidence: ledger:E0634, ledger:E1221</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-30" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="-10" />
      <LABEL index="3" value="0" />
      <LABEL index="4" value="10" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="40" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="60" />
      <LABEL index="10" value="70" />
      <LABEL index="11" value="80" />
      <LABEL index="12" value="90" />
      <LABEL index="13" value="100" />
      <LABEL index="14" value="110" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="130" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2279A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5A8" flags="0x30">
    <title>Idle A/C Turn-On Airflow vs A/C Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra idle airflow added when the A/C compressor turns on, by A/C refrigerant pressure (0 to 3600 kPa). It is added to the intake temperature term, held for the A/C turn-on hold time, then removed by the A/C hold airflow decay step. Stock 1.5 g/s up to 675 kPa, rising to 2.15 g/s from 1800 kPa. Effect: raise = more extra idle airflow when the A/C compressor turns on at that refrigerant pressure Evidence: ledger:E0634, ledger:E1221</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="225" />
      <LABEL index="2" value="450" />
      <LABEL index="3" value="675" />
      <LABEL index="4" value="900" />
      <LABEL index="5" value="1125" />
      <LABEL index="6" value="1350" />
      <LABEL index="7" value="1575" />
      <LABEL index="8" value="1800" />
      <LABEL index="9" value="2025" />
      <LABEL index="10" value="2250" />
      <LABEL index="11" value="2475" />
      <LABEL index="12" value="2700" />
      <LABEL index="13" value="2925" />
      <LABEL index="14" value="3150" />
      <LABEL index="15" value="3375" />
      <LABEL index="16" value="3600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x227BE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5A9" flags="0x30">
    <title>Intake Air Temp Sensor - Temperature Points</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Temperature at each of the 33 sensor resistance points (stock 150 C down to -40 C in 5.9 C steps); the PCM interpolates between them to get intake air temperature. Effect: reported and used intake air temperature Evidence: ledger:E0638, ledger:E1047</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x290A0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5AA" flags="0x0">
    <title>Idle Speed Diagnostic Enable - Barometric Pressure Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle speed diagnostic (P0506 idle rpm lower than expected, P0507 higher than expected) only runs while barometric pressure is at or above this. Stock 75 kPa. Effect: raise = the diagnostic stops running at a lower altitude Evidence: ledger:E0640, ledger:E0679, ledger:E0898, ledger:E0985</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5AB" flags="0x30">
    <title>Idle A/C - Settle Time vs Compressor Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: after the idle air adder has decayed, how long the A/C transient is still flagged (idle learning and the airflow integral stay blocked), by A/C compressor torque 0 to 80 Nm. Stock 0.5 s everywhere. Effect: raise = idle learning stays blocked longer after an A/C clutch change Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>Nm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x291B8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5AC" flags="0x0">
    <title>Idle Airflow Model - Correction Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter weight on the idle airflow model&#x27;s correction term: each pass the term moves this share of the way to its new estimate, then it is held between the Idle RPM-Select ceiling and floor tables. Stock 0.05 (5 percent per pass). Range 0 to 1.0. Effect: raise = the correction term follows each new estimate faster Evidence: ledger:E0643, ledger:E1202</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2242A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5AD" flags="0x30">
    <title>Cam Alternate Mode - Desired Cam vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam alternate mode: replaces the desired exhaust cam angle with this chain once engine speed reaches 8100 rpm in idle spark mode after 3 s of running. Desired cam by engine speed (0 to 2048 rpm), times the barometric and coolant factors. Stock 0. Dormant: the stock calibration never reaches that speed in idle spark mode, so it has no effect on this truck&#x27;s software. Effect: raise = more cam angle in the alternate mode Evidence: ledger:E0644, ledger:E0737, ledger:E0936, ledger:E1229</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22CAC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5AE" flags="0x30">
    <title>Cruise Control - Target Speed Offset vs Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: added to the vehicle speed when the cruise control takes its target speed (set and the matching resume step), by vehicle speed (38 to 180 km/h). Stock 0 at every speed, so the target is the speed itself. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = the cruise target is set above the current speed) Evidence: ledger:E0644, ledger:E0936, ledger:E1261</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.875" />
      <LABEL index="2" value="55.75" />
      <LABEL index="3" value="64.625" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.375" />
      <LABEL index="6" value="91.25" />
      <LABEL index="7" value="100.125" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.875" />
      <LABEL index="10" value="126.75" />
      <LABEL index="11" value="135.625" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.375" />
      <LABEL index="14" value="162.25" />
      <LABEL index="15" value="171.125" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21F74" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5AF" flags="0x30">
    <title>Load Cam Target Offset vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Load cam target offset: once a fuel start-up ramp has finished, an offset is taken off the load-based cam target: the offset by engine speed, times a factor by time since it became active, times a factor by cylinder airmass. Stock all three tables are zero, so the offset is off; filling them switches it on. This is the offset by engine speed. Effect: raise = less cam angle from the load target at that speed Evidence: ledger:E0644, ledger:E0876</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="400" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1200" />
      <LABEL index="4" value="1600" />
      <LABEL index="5" value="2000" />
      <LABEL index="6" value="2400" />
      <LABEL index="7" value="2800" />
      <LABEL index="8" value="3200" />
      <LABEL index="9" value="3600" />
      <LABEL index="10" value="4000" />
      <LABEL index="11" value="4400" />
      <LABEL index="12" value="4800" />
      <LABEL index="13" value="5200" />
      <LABEL index="14" value="5600" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22FFA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5B0" flags="0x30">
    <title>Load Cam Target Offset - Time Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Load cam target offset: once a fuel start-up ramp has finished, an offset is taken off the load-based cam target: the offset by engine speed, times a factor by time since it became active, times a factor by cylinder airmass. Stock all three tables are zero, so the offset is off; filling them switches it on. This is the factor by time since the offset became active. Effect: raise = more of the offset at that time Evidence: ledger:E0644, ledger:E0876</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>s (since active)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2301E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5B1" flags="0x30">
    <title>Load Cam Target Offset - Airmass Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Load cam target offset: once a fuel start-up ramp has finished, an offset is taken off the load-based cam target: the offset by engine speed, times a factor by time since it became active, times a factor by cylinder airmass. Stock all three tables are zero, so the offset is off; filling them switches it on. This is the factor by cylinder airmass. Effect: raise = more of the offset at that airmass Evidence: ledger:E0644, ledger:E0876</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>g/cyl (airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23042" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5B2" flags="0x30">
    <title>Engine Oil Pressure Estimate - Low Oil Pressure Input Table</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Oil pressure estimate used instead of the main estimate table while the low oil pressure input is active (coolant -40 to 152 C by engine speed 400 to 3600 rpm in five points). All zero on stock, so 0 kPa is reported while the input is active. Effect: changes the oil pressure reported while the low oil pressure input is active Evidence: ledger:E0274, ledger:E0644, ledger:E0675, ledger:E1246, ledger:E1831</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="1200" />
      <LABEL index="2" value="2000" />
      <LABEL index="3" value="2800" />
      <LABEL index="4" value="3600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2340C" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5B3" flags="0x30">
    <title>Purge O2 Feedback - Reference Flow Needed to Step Up vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: the purge factor may step up only while the purge reference flow at the present manifold vacuum is above this, by engine airflow (0 to 128 g/s). Stock 0: no restriction except at zero vacuum. Purge flow units: the full scale word (stock 123) is full purge reference flow. Effect: raise = the purge factor only rises when more manifold vacuum is available Evidence: ledger:E1122</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <LABEL index="17" value="68" />
      <LABEL index="18" value="72" />
      <LABEL index="19" value="76" />
      <LABEL index="20" value="80" />
      <LABEL index="21" value="84" />
      <LABEL index="22" value="88" />
      <LABEL index="23" value="92" />
      <LABEL index="24" value="96" />
      <LABEL index="25" value="100" />
      <LABEL index="26" value="104" />
      <LABEL index="27" value="108" />
      <LABEL index="28" value="112" />
      <LABEL index="29" value="116" />
      <LABEL index="30" value="120" />
      <LABEL index="31" value="124" />
      <LABEL index="32" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25184" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flow units</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5B4" flags="0x30">
    <title>Closed Loop Minimum MAP vs Baro</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel is not used while manifold pressure is below this, by barometric pressure (65 to 105 kPa). Stock 0 at every point: no limit. Effect: raise = closed loop is given up at light load (low MAP) Evidence: ledger:E1127</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa baro</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="65" />
      <LABEL index="1" value="70" />
      <LABEL index="2" value="75" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="85" />
      <LABEL index="5" value="90" />
      <LABEL index="6" value="95" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25C1A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5B5" flags="0x30">
    <title>Acceleration Fuel Adder - Gain vs Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra fuel on acceleration: share of each rise in the calculated fuel per cylinder that is added on top as extra fuel, by port temperature. Only used while wall film compensation is enabled. Stock 0 at every point: the adder is off and the wall film compensation does all transient fuelling. Effect: raise = more extra fuel when the fuel demand rises Evidence: ledger:E1127</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (port temp model)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-24" />
      <LABEL index="2" value="-8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="24" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="56" />
      <LABEL index="7" value="72" />
      <LABEL index="8" value="88" />
      <LABEL index="9" value="104" />
      <LABEL index="10" value="120" />
      <LABEL index="11" value="136" />
      <LABEL index="12" value="152" />
      <LABEL index="13" value="168" />
      <LABEL index="14" value="184" />
      <LABEL index="15" value="200" />
      <LABEL index="16" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2672E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5B6" flags="0x30">
    <title>PE Enable Throttle - Adder vs Baro</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the power enrichment (PE) enable throttle threshold (PE enable throttle vs RPM) by barometric pressure. Stock 0 at every baro. Effect: raise = more throttle is needed before PE enables at that barometric pressure Evidence: ledger:E0644, ledger:E1397</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="65" />
      <LABEL index="1" value="70" />
      <LABEL index="2" value="75" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="85" />
      <LABEL index="5" value="90" />
      <LABEL index="6" value="95" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28BB8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5B7" flags="0x30">
    <title>Idle Airflow RPM Adder - Reduction vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: airflow taken off the rpm airflow adder, by engine speed (400 to 3600 rpm). Stock 0 everywhere. Effect: raise = less feed-forward airflow at that engine speed Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2933A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5B8" flags="0x30">
    <title>Idle Airflow - Correction Term vs Converter Slip (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added by filtered torque converter slip (-256 to +256 rpm), at road speed with the throttle closed, outside decel fuel cut, once the idle airflow error has settled. Stock 0 at every slip. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = more idle airflow at that converter slip) Evidence: ledger:E0644, ledger:E0897, ledger:E0936, ledger:E1280</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm (converter slip, filtered)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-256" />
      <LABEL index="1" value="-240" />
      <LABEL index="2" value="-224" />
      <LABEL index="3" value="-208" />
      <LABEL index="4" value="-192" />
      <LABEL index="5" value="-176" />
      <LABEL index="6" value="-160" />
      <LABEL index="7" value="-144" />
      <LABEL index="8" value="-128" />
      <LABEL index="9" value="-112" />
      <LABEL index="10" value="-96" />
      <LABEL index="11" value="-80" />
      <LABEL index="12" value="-64" />
      <LABEL index="13" value="-48" />
      <LABEL index="14" value="-32" />
      <LABEL index="15" value="-16" />
      <LABEL index="16" value="0" />
      <LABEL index="17" value="16" />
      <LABEL index="18" value="32" />
      <LABEL index="19" value="48" />
      <LABEL index="20" value="64" />
      <LABEL index="21" value="80" />
      <LABEL index="22" value="96" />
      <LABEL index="23" value="112" />
      <LABEL index="24" value="128" />
      <LABEL index="25" value="144" />
      <LABEL index="26" value="160" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="192" />
      <LABEL index="29" value="208" />
      <LABEL index="30" value="224" />
      <LABEL index="31" value="240" />
      <LABEL index="32" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29374" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5B9" flags="0x30">
    <title>Idle RPM Event - Drop per Update Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. An idle speed drop larger than this in one 12.5 ms update starts a drop event, by desired idle (400 to 1200 rpm). Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0644, ledger:E1505</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="450" />
      <LABEL index="2" value="500" />
      <LABEL index="3" value="550" />
      <LABEL index="4" value="600" />
      <LABEL index="5" value="650" />
      <LABEL index="6" value="700" />
      <LABEL index="7" value="750" />
      <LABEL index="8" value="800" />
      <LABEL index="9" value="850" />
      <LABEL index="10" value="900" />
      <LABEL index="11" value="950" />
      <LABEL index="12" value="1000" />
      <LABEL index="13" value="1050" />
      <LABEL index="14" value="1100" />
      <LABEL index="15" value="1150" />
      <LABEL index="16" value="1200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A032" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5BA" flags="0x30">
    <title>Idle RPM Event - Rise per Update Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. An idle speed rise larger than this in one 12.5 ms update starts a rise event, by desired idle (400 to 1200 rpm). Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0644, ledger:E1505</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="450" />
      <LABEL index="2" value="500" />
      <LABEL index="3" value="550" />
      <LABEL index="4" value="600" />
      <LABEL index="5" value="650" />
      <LABEL index="6" value="700" />
      <LABEL index="7" value="750" />
      <LABEL index="8" value="800" />
      <LABEL index="9" value="850" />
      <LABEL index="10" value="900" />
      <LABEL index="11" value="950" />
      <LABEL index="12" value="1000" />
      <LABEL index="13" value="1050" />
      <LABEL index="14" value="1100" />
      <LABEL index="15" value="1150" />
      <LABEL index="16" value="1200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A056" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5BB" flags="0x30">
    <title>Idle Load State - Park/Neutral Delay vs Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle tables, Park / Neutral or in gear rows: delay after a shift to Park / Neutral before the Park / Neutral rows of all idle tables are used, by transmission fluid temperature (-40 to 152 C). Stock 0 everywhere: they are used on the next pass. Effect: raise = the in gear rows stay in use longer after a shift to Park / Neutral Evidence: ledger:E1113</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A754" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5BC" flags="0x30">
    <title>Alternate VE Table A vs Throttle Area x RPM (airflow mode 2, dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Alternate volumetric efficiency table A, by throttle area (rows) and engine speed (columns), for a special airflow mode that computes the VE from throttle area instead of the cam-phase VE banks. Tables A and B are blended by barometric pressure and the result replaces the normal VE bank value, in the same unit (mg K / kPa per cylinder, as the VE banks). The stock calibration can never enter that airflow mode (its entry windows are all zero), and the table is all zero on stock. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0644, ledger:E0735, ledger:E0863, ledger:E1148, led...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>% throttle area</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2BDC6" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mg K/kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5BD" flags="0x30">
    <title>Alternate VE Table B vs Throttle Area x RPM (airflow mode 2, dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Alternate volumetric efficiency table B, by throttle area (rows) and engine speed (columns), for a special airflow mode that computes the VE from throttle area instead of the cam-phase VE banks. Tables A and B are blended by barometric pressure and the result replaces the normal VE bank value, in the same unit (mg K / kPa per cylinder, as the VE banks). The stock calibration can never enter that airflow mode (its entry windows are all zero), and the table is all zero on stock. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0644, ledger:E0735, ledger:E0863, ledger:E1148, led...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>% throttle area</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C00E" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mg K/kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5BE" flags="0x30">
    <title>O2 Heater - Upstream Duty During Turn-On Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor heater: upstream heater duty while the turn-on delay after start is still running, by coolant temperature at start-up. Stock 0 % everywhere (heater off during the delay). Effect: raise = the upstream heater is run gently during the delay Evidence: ledger:E1062</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C75C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5BF" flags="0x30">
    <title>Spark Mode Ramp - Unused Mode to Off Idle vs Throttle (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this ramp belongs to a spark mode that no code ever selects. Spark reference ramp: when the spark mode changes (cranking, idle, first idle after start, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This curve would be the ramp from that unused mode to off idle, by throttle (0 to 100 % in 10 % steps). Stock all 0. Dormant: no effect on this truck&#x27;s software. Effect: none on this calibration (the spark mode it belongs to is never selected) Evidence: ledger:E0644, ledger:E0894, ledger:E1240</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>%</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F1CE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>update cycles</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5C0" flags="0x30">
    <title>O2 Response Test (P1134) - Min Time Ratio (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Used only by the ratio form of the P1134 test, which stock does not select. Stock 0. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: no effect on stock (inactive) Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x348AE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5C1" flags="0x30">
    <title>O2 Response Test - Max Average Lean-to-Rich Time, Second Sensor (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Copy of the sensor 1 limit for a second front O2 sensor. The H3 tests one sensor, so this is never used. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: no effect on stock (inactive) Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34932" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ms</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>63999.023438</max>
      <MATH equation="X/1.024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5C2" flags="0x30">
    <title>O2 Response Test - Max Average Rich-to-Lean Time, Second Sensor (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Copy of the sensor 1 limit for a second front O2 sensor. The H3 tests one sensor, so this is never used. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: no effect on stock (inactive) Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3498A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ms</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>63999.023438</max>
      <MATH equation="X/1.024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5C3" flags="0x30">
    <title>O2 Response Test - Min Time Ratio, Second Sensor (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Copy of the sensor 1 limit for a second front O2 sensor. The H3 tests one sensor, so this is never used. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: no effect on stock (inactive) Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34A0E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5C4" flags="0x30">
    <title>O2 Response Test - Max Time Difference, Second Sensor (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Copy of the sensor 1 limit for a second front O2 sensor. The H3 tests one sensor, so this is never used. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: no effect on stock (inactive) Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34ABE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>ms</units>
      <decimalpl>1</decimalpl>
      <min>-32000.000000</min>
      <max>31999.023438</max>
      <MATH equation="X/1.024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5C5" flags="0x30">
    <title>O2 Response Test - Min Time Difference, Second Sensor (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Copy of the sensor 1 limit for a second front O2 sensor. The H3 tests one sensor, so this is never used. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: no effect on stock (inactive) Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34B16" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>ms</units>
      <decimalpl>1</decimalpl>
      <min>-32000.000000</min>
      <max>31999.023438</max>
      <MATH equation="X/1.024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5C6" flags="0x30">
    <title>Misfire - Pause Floor vs Coolant (no effect at stock)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: every update the misfire pause count, in engine cycles, is raised to at least this value for the current coolant temperature, so a non-zero value keeps misfire detection paused at that temperature. Works like the general misfire pause. Stock 0 at every temperature, so it has no effect on the stock calibration. Raising it stops misfire detection at those temperatures. Effect: raise = misfire detection held off at that coolant temperature Evidence: ledger:E0772, ledger:E1878</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-10" />
      <LABEL index="1" value="-4" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="14" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="26" />
      <LABEL index="7" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x371EC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>cycles</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5C7" flags="0x30">
    <title>Cruise Control - Cancel Speed Drop Below Target vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: an active cruise is cancelled when vehicle speed falls this far below the cruise target speed (negative = below the target). Looked up by vehicle speed (38 to 180 km/h). Stock -15 km/h at 38 km/h, -34 km/h at 80 km/h, -39 km/h from 127 km/h up. Effect: more negative = the cruise stays on through a bigger speed drop Evidence: ledger:E0646, ledger:E0730, ledger:E0839, ledger:E1256</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.875" />
      <LABEL index="2" value="55.75" />
      <LABEL index="3" value="64.625" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.375" />
      <LABEL index="6" value="91.25" />
      <LABEL index="7" value="100.125" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.875" />
      <LABEL index="10" value="126.75" />
      <LABEL index="11" value="135.625" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.375" />
      <LABEL index="14" value="162.25" />
      <LABEL index="15" value="171.125" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21F08" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5C8" flags="0x30">
    <title>Cruise Control - Cancel at Deceleration vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control cancels when the vehicle slows down faster than this (filtered change of vehicle speed, negative = slowing), by vehicle speed. Stock -40 km/h per second at every speed, far beyond normal braking, so in practice this catches a speed signal that drops out. Effect: closer to 0 = cruise cancels on gentler deceleration Evidence: ledger:E0647, ledger:E0730, ledger:E0839, ledger:E1164, ledger:E1167</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.875" />
      <LABEL index="2" value="55.75" />
      <LABEL index="3" value="64.625" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.375" />
      <LABEL index="6" value="91.25" />
      <LABEL index="7" value="100.125" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.875" />
      <LABEL index="10" value="126.75" />
      <LABEL index="11" value="135.625" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.375" />
      <LABEL index="14" value="162.25" />
      <LABEL index="15" value="171.125" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21F2C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per s</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5C9" flags="0x30">
    <title>Cruise Control - Cancel at Acceleration vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control cancels when the vehicle gains speed faster than this (filtered change of vehicle speed), by vehicle speed. Stock +16 km/h per second at every speed, which normal driving does not reach, so in practice this catches wheel spin or a jumping speed signal. Effect: lower = cruise cancels on gentler acceleration Evidence: ledger:E0647, ledger:E0730, ledger:E0839, ledger:E1164, ledger:E1167</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.875" />
      <LABEL index="2" value="55.75" />
      <LABEL index="3" value="64.625" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.375" />
      <LABEL index="6" value="91.25" />
      <LABEL index="7" value="100.125" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.875" />
      <LABEL index="10" value="126.75" />
      <LABEL index="11" value="135.625" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.375" />
      <LABEL index="14" value="162.25" />
      <LABEL index="15" value="171.125" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21F50" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per s</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5CA" flags="0x0">
    <title>Idle Sequencer - State 1 Advance Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed sequencer: time spent in state 1 before it may advance to state 2. Stock 0 s (advances at once). Effect: raise = the sequencer stays longer in state 1 Evidence: ledger:E0648, ledger:E1265</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2973A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>-204.800000</min>
    <max>204.793750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5CB" flags="0x0">
    <title>Idle Sequencer - Rpm Over Desired Hold Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed sequencer: time engine speed must stay above the desired idle speed by more than the allowed margin before the sequencer advances from state 1 to state 2. Stock 0 s. Effect: raise = rpm must stay high longer before the sequencer moves on Evidence: ledger:E0649, ledger:E1265</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2973E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>-204.800000</min>
    <max>204.793750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5CC" flags="0x0">
    <title>Idle Disturbance Latch - Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: the disturbance latch can set only above this vehicle speed. Stock 512 km/h: off. The disturbance latch: in closed loop idle speed control with the throttle closed, a sudden rpm change above a speed threshold puts the idle controller back in its moving mode for a time. Effect: lower = the latch can set at lower speed Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2974A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5CD" flags="0x0">
    <title>First-Run Mode - Post-Start Airflow Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First-run mode runs only during the first 12 s of engine running recorded by the PCM. During it the post-start airflow is applied whatever the post-start time limit and is multiplied by this. Stock 5.0. Effect: raise = more post-start airflow during first-run mode Evidence: ledger:E0652, ledger:E1232</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x29756" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>2</decimalpl>
    <min>-16.000000</min>
    <max>15.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5CE" flags="0x30">
    <title>First-Run Mode - Open-Loop Fuel Multiplier vs Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First-run mode runs only during the first 12 s of engine running recorded by the PCM (kept through power-off), with a stored flag set, the mode enable set and start-up coolant inside the coolant window. During it the open-loop commanded fuel/air ratio is multiplied by this, by recorded run time (0 to 64 s). Stock 1.99 up to 6 s, 1.65 at 8 s, 1.30 at 10 s, 1.0 from 12 s. Effect: raise = richer open-loop fuel during first-run mode at that recorded run time Evidence: ledger:E0653, ledger:E0937, ledger:E1227</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="4" />
      <LABEL index="3" value="6" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="12" />
      <LABEL index="7" value="14" />
      <LABEL index="8" value="16" />
      <LABEL index="9" value="18" />
      <LABEL index="10" value="20" />
      <LABEL index="11" value="22" />
      <LABEL index="12" value="24" />
      <LABEL index="13" value="26" />
      <LABEL index="14" value="28" />
      <LABEL index="15" value="30" />
      <LABEL index="16" value="32" />
      <LABEL index="17" value="34" />
      <LABEL index="18" value="36" />
      <LABEL index="19" value="38" />
      <LABEL index="20" value="40" />
      <LABEL index="21" value="42" />
      <LABEL index="22" value="44" />
      <LABEL index="23" value="46" />
      <LABEL index="24" value="48" />
      <LABEL index="25" value="50" />
      <LABEL index="26" value="52" />
      <LABEL index="27" value="54" />
      <LABEL index="28" value="56" />
      <LABEL index="29" value="58" />
      <LABEL index="30" value="60" />
      <LABEL index="31" value="62" />
      <LABEL index="32" value="64" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28B46" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5CF" flags="0x30">
    <title>Fuel Level vs Sender Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converts the fuel tank level sender voltage (0 to 5 V in 0.156 V steps) to the fuel level the PCM reports on the fuel level PID and uses for its EVAP leak tests. Cells are fuel level in %. Stock reads full (101 %) up to about 0.8 V and falls to empty at about 2.7 V. Change it only to match a different sender. Effect: raise = the PCM reads a fuller tank at that sender voltage Evidence: ledger:E0655, ledger:E0936, ledger:E0955</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>V (fuel level sender)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.156" />
      <LABEL index="2" value="0.312" />
      <LABEL index="3" value="0.469" />
      <LABEL index="4" value="0.625" />
      <LABEL index="5" value="0.781" />
      <LABEL index="6" value="0.938" />
      <LABEL index="7" value="1.094" />
      <LABEL index="8" value="1.25" />
      <LABEL index="9" value="1.406" />
      <LABEL index="10" value="1.562" />
      <LABEL index="11" value="1.719" />
      <LABEL index="12" value="1.875" />
      <LABEL index="13" value="2.031" />
      <LABEL index="14" value="2.188" />
      <LABEL index="15" value="2.344" />
      <LABEL index="16" value="2.5" />
      <LABEL index="17" value="2.656" />
      <LABEL index="18" value="2.812" />
      <LABEL index="19" value="2.969" />
      <LABEL index="20" value="3.125" />
      <LABEL index="21" value="3.281" />
      <LABEL index="22" value="3.438" />
      <LABEL index="23" value="3.594" />
      <LABEL index="24" value="3.75" />
      <LABEL index="25" value="3.906" />
      <LABEL index="26" value="4.062" />
      <LABEL index="27" value="4.219" />
      <LABEL index="28" value="4.375" />
      <LABEL index="29" value="4.531" />
      <LABEL index="30" value="4.688" />
      <LABEL index="31" value="4.844" />
      <LABEL index="32" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x364CE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% fuel level</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>292.763011</max>
      <MATH equation="X/223.85"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5D0" flags="0x30">
    <title>PE Delay Countdown Rate vs Throttle x RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How much power-enrichment (PE) delay time is removed each update while PE is requested, by throttle and rpm. The PE delay store fills up to PE Delay - Maximum Delay Store while PE is not requested and must drain before a delayed PE request takes effect. Stock 0.05 s per update at low throttle and rpm, rising to 0.35 to 0.5 s at high throttle and high rpm. Effect: raise = the power-enrichment (PE) delay timer counts down faster at that throttle/rpm cell, shortening the PE delay Evidence: ledger:E0654, ledger:E0704, ledger:E1329, ledger:E1337</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% (throttle)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28BE8" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s per update</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5D1" flags="0x30">
    <title>A/C Refrigerant Pressure Sensor Transfer</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converts the A/C refrigerant pressure sensor voltage (0 to 4.95 V) to pressure. The result is the pressure used by the A/C compressor cut-outs and the A/C idle airflow. Stock 0 kPa at 0 V rising about 227 kPa per 0.31 V to 3446 kPa at 4.95 V. Effect: raise = a higher pressure reading for the same sensor voltage Evidence: ledger:E0662, ledger:E0937, ledger:E1223</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>V</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.309" />
      <LABEL index="2" value="0.619" />
      <LABEL index="3" value="0.928" />
      <LABEL index="4" value="1.238" />
      <LABEL index="5" value="1.547" />
      <LABEL index="6" value="1.856" />
      <LABEL index="7" value="2.166" />
      <LABEL index="8" value="2.475" />
      <LABEL index="9" value="2.785" />
      <LABEL index="10" value="3.094" />
      <LABEL index="11" value="3.403" />
      <LABEL index="12" value="3.713" />
      <LABEL index="13" value="4.022" />
      <LABEL index="14" value="4.332" />
      <LABEL index="15" value="4.641" />
      <LABEL index="16" value="4.95" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20138" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5D2" flags="0x0">
    <title>P1545 Circuit Check - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Output circuit check P1545 only runs with engine speed at or above this. Stock 425 rpm. Effect: raise = the check needs a higher engine speed Evidence: ledger:E1058</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32696" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5D3" flags="0x0">
    <title>Traction Control - Minimum Engine Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control torque reduction: it is allowed only after the engine has run longer than this. Stock 2 s. Effect: raise = no torque reduction until later after the start Evidence: ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30334" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5D4" flags="0x0">
    <title>Traction Control - Torque Signal Full Scale</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control: engine torque that the top of the signal range stands for, on both the torque request coming from the brake module and the delivered torque signal going back to it. It is also the request used while the signal is invalid (no limit). It has to match the brake module. Stock 350 Nm. Effect: changing it rescales the incoming torque request and the outgoing delivered torque together Evidence: ledger:E0666, ledger:E0918, ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3031A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>16383.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5D5" flags="0x30">
    <title>Traction Control - Torque Request Floor vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The traction control sends the engine a torque limit; while traction control is active it becomes the electronic throttle torque limit. The request is never lower than this value at the current engine speed. Stock 30 Nm at 0 and 512 rpm, 0 from 1024 rpm. Effect: raise = traction control cannot pull torque below this at that rpm Evidence: ledger:E0667, ledger:E0918</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30E3A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5D6" flags="0x0">
    <title>Traction Control - Minimum Engine Speed, Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control torque reduction: once allowed, it stays allowed until engine speed falls to this. Stock 500 rpm. Effect: raise = torque reduction is dropped at a higher engine speed Evidence: ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30332" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5D7" flags="0x0">
    <title>Traction Control - Minimum Engine Speed, On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control torque reduction: it is allowed once engine speed is above this. Stock 600 rpm. Effect: raise = no torque reduction until a higher engine speed Evidence: ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30330" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5D8" flags="0x30">
    <title>Purge Flow - Maximum Request vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge: highest purge flow request at each engine airflow (0 to 128 g/s), before the purge factors scale it down. Stock 0 at no airflow rising to 123 from 24 g/s. Purge flow units: the full scale word (stock 123) is full purge reference flow. Effect: raise = more purge at that engine airflow Evidence: ledger:E1122</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <LABEL index="17" value="68" />
      <LABEL index="18" value="72" />
      <LABEL index="19" value="76" />
      <LABEL index="20" value="80" />
      <LABEL index="21" value="84" />
      <LABEL index="22" value="88" />
      <LABEL index="23" value="92" />
      <LABEL index="24" value="96" />
      <LABEL index="25" value="100" />
      <LABEL index="26" value="104" />
      <LABEL index="27" value="108" />
      <LABEL index="28" value="112" />
      <LABEL index="29" value="116" />
      <LABEL index="30" value="120" />
      <LABEL index="31" value="124" />
      <LABEL index="32" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25224" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flow units</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5D9" flags="0x30">
    <title>Purge Learned Memory Weight vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: how much of the purge learned memory correction is applied, by airflow (0 to 128 g/s). Stock: all of it up to 32 g/s, falling to one tenth from 104 g/s. Effect: raise = more of the purge correction is applied at that airflow Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <LABEL index="17" value="68" />
      <LABEL index="18" value="72" />
      <LABEL index="19" value="76" />
      <LABEL index="20" value="80" />
      <LABEL index="21" value="84" />
      <LABEL index="22" value="88" />
      <LABEL index="23" value="92" />
      <LABEL index="24" value="96" />
      <LABEL index="25" value="100" />
      <LABEL index="26" value="104" />
      <LABEL index="27" value="108" />
      <LABEL index="28" value="112" />
      <LABEL index="29" value="116" />
      <LABEL index="30" value="120" />
      <LABEL index="31" value="124" />
      <LABEL index="32" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2572C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5DA" flags="0x30">
    <title>Port Temperature Model Target - Air-Fuel Ratio Offset vs AFR</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. By commanded air-fuel ratio: the model&#x27;s air-fuel ratio terms use the average of the commanded air-fuel ratio and this value. Stock 12.0 at 0 AFR falling to 1.0 at 19.2 AFR, 0 from 20 AFR. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = the air-fuel ratio terms see a leaner effective ratio...</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>AFR (commanded)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.8" />
      <LABEL index="2" value="1.6" />
      <LABEL index="3" value="2.4" />
      <LABEL index="4" value="3.2" />
      <LABEL index="5" value="4" />
      <LABEL index="6" value="4.8" />
      <LABEL index="7" value="5.6" />
      <LABEL index="8" value="6.4" />
      <LABEL index="9" value="7.2" />
      <LABEL index="10" value="8" />
      <LABEL index="11" value="8.8" />
      <LABEL index="12" value="9.6" />
      <LABEL index="13" value="10.4" />
      <LABEL index="14" value="11.2" />
      <LABEL index="15" value="12" />
      <LABEL index="16" value="12.8" />
      <LABEL index="17" value="13.6" />
      <LABEL index="18" value="14.4" />
      <LABEL index="19" value="15.2" />
      <LABEL index="20" value="16" />
      <LABEL index="21" value="16.8" />
      <LABEL index="22" value="17.6" />
      <LABEL index="23" value="18.4" />
      <LABEL index="24" value="19.2" />
      <LABEL index="25" value="20" />
      <LABEL index="26" value="20.8" />
      <LABEL index="27" value="21.6" />
      <LABEL index="28" value="22.4" />
      <LABEL index="29" value="23.2" />
      <LABEL index="30" value="24" />
      <LABEL index="31" value="24.8" />
      <LABEL index="32" value="25.6" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AAD6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>AFR</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>31.999512</max>
      <MATH equation="X/2048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5DB" flags="0x30">
    <title>Port Temperature Model - Response Rate vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the modelled intake port temperature (used by the transient wall-wetting fuel) moves toward its target each update, by airflow. Stock 0.8 % of the gap at no airflow rising to 8 % from about 210 g/s. Effect: raise = the port temperature model follows its target faster Evidence: ledger:E0741</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <LABEL index="9" value="144" />
      <LABEL index="10" value="160" />
      <LABEL index="11" value="176" />
      <LABEL index="12" value="192" />
      <LABEL index="13" value="208" />
      <LABEL index="14" value="224" />
      <LABEL index="15" value="240" />
      <LABEL index="16" value="256" />
      <LABEL index="17" value="272" />
      <LABEL index="18" value="288" />
      <LABEL index="19" value="304" />
      <LABEL index="20" value="320" />
      <LABEL index="21" value="336" />
      <LABEL index="22" value="352" />
      <LABEL index="23" value="368" />
      <LABEL index="24" value="384" />
      <LABEL index="25" value="400" />
      <LABEL index="26" value="416" />
      <LABEL index="27" value="432" />
      <LABEL index="28" value="448" />
      <LABEL index="29" value="464" />
      <LABEL index="30" value="480" />
      <LABEL index="31" value="496" />
      <LABEL index="32" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AB1E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5DC" flags="0x30">
    <title>Calculated Load - IAT Density Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intake air temperature factor on the 100 % calculated load airflow. Only changes the calculated load value reported to a scan tool (PID 04). Stock 1.13 at -40 C falling to 0.85 at 140 C. Effect: raise = lower reported calculated load at that intake temperature Evidence: ledger:E0740, ledger:E1340</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-34.375" />
      <LABEL index="2" value="-28.75" />
      <LABEL index="3" value="-23.125" />
      <LABEL index="4" value="-17.5" />
      <LABEL index="5" value="-11.875" />
      <LABEL index="6" value="-6.25" />
      <LABEL index="7" value="-0.625" />
      <LABEL index="8" value="5" />
      <LABEL index="9" value="10.625" />
      <LABEL index="10" value="16.25" />
      <LABEL index="11" value="21.875" />
      <LABEL index="12" value="27.5" />
      <LABEL index="13" value="33.125" />
      <LABEL index="14" value="38.75" />
      <LABEL index="15" value="44.375" />
      <LABEL index="16" value="50" />
      <LABEL index="17" value="55.625" />
      <LABEL index="18" value="61.25" />
      <LABEL index="19" value="66.875" />
      <LABEL index="20" value="72.5" />
      <LABEL index="21" value="78.125" />
      <LABEL index="22" value="83.75" />
      <LABEL index="23" value="89.375" />
      <LABEL index="24" value="95" />
      <LABEL index="25" value="100.625" />
      <LABEL index="26" value="106.25" />
      <LABEL index="27" value="111.875" />
      <LABEL index="28" value="117.5" />
      <LABEL index="29" value="123.125" />
      <LABEL index="30" value="128.75" />
      <LABEL index="31" value="134.375" />
      <LABEL index="32" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C2D4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5DD" flags="0x30">
    <title>Airflow Rationality - High Throttle Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101): throttle position, by engine speed (400 to 6800 rpm), above which only the first pressure check (P0106) is judged and the airflow, second pressure and throttle checks are held at zero. Stock 25 % up to 1200 rpm, 32 % at 1400 rpm, 45 % from 1600 rpm. Effect: raise = the full set of checks runs up to a higher throttle position Evidence: ledger:E0772, ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1000" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1400" />
      <LABEL index="6" value="1600" />
      <LABEL index="7" value="1800" />
      <LABEL index="8" value="2000" />
      <LABEL index="9" value="2200" />
      <LABEL index="10" value="2400" />
      <LABEL index="11" value="2600" />
      <LABEL index="12" value="2800" />
      <LABEL index="13" value="3000" />
      <LABEL index="14" value="3200" />
      <LABEL index="15" value="3400" />
      <LABEL index="16" value="3600" />
      <LABEL index="17" value="3800" />
      <LABEL index="18" value="4000" />
      <LABEL index="19" value="4200" />
      <LABEL index="20" value="4400" />
      <LABEL index="21" value="4600" />
      <LABEL index="22" value="4800" />
      <LABEL index="23" value="5000" />
      <LABEL index="24" value="5200" />
      <LABEL index="25" value="5400" />
      <LABEL index="26" value="5600" />
      <LABEL index="27" value="5800" />
      <LABEL index="28" value="6000" />
      <LABEL index="29" value="6200" />
      <LABEL index="30" value="6400" />
      <LABEL index="31" value="6600" />
      <LABEL index="32" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3674C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5DE" flags="0x30">
    <title>Charge Temperature Conversion (C to K)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converts the blended intake and coolant temperature into the absolute charge temperature used by the cranking airmass calculation (ideal gas law). Stock is an exact Celsius to Kelvin conversion, 233 K at -40 C to 413 K at 140 C. Effect: raise = less cranking airmass (leaner cranking fuel) at that temperature; stock is exact physics Evidence: ledger:E0772, ledger:E0803, ledger:E0861</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>degC (intake / coolant blend)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <LABEL index="17" value="130" />
      <LABEL index="18" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B1BA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>K</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5DF" flags="0x30">
    <title>Cam Phaser Integrator Step (Advance)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Duty added to the exhaust cam phaser&#x27;s integrator every 12.5 ms while the actual cam is short of desired, by the size of the error (full scale about 1.6 deg). Stock 0.003 % for a tiny error to 0.12 % at full scale. Effect: raise = the cam phaser duty climbs faster when the cam is short of its target Evidence: ledger:E0670, ledger:E0737, ledger:E1226</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>fraction of 1.6 deg error</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.062" />
      <LABEL index="2" value="0.125" />
      <LABEL index="3" value="0.188" />
      <LABEL index="4" value="0.25" />
      <LABEL index="5" value="0.312" />
      <LABEL index="6" value="0.375" />
      <LABEL index="7" value="0.438" />
      <LABEL index="8" value="0.5" />
      <LABEL index="9" value="0.562" />
      <LABEL index="10" value="0.625" />
      <LABEL index="11" value="0.688" />
      <LABEL index="12" value="0.75" />
      <LABEL index="13" value="0.812" />
      <LABEL index="14" value="0.875" />
      <LABEL index="15" value="0.938" />
      <LABEL index="16" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22B8A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5E0" flags="0x30">
    <title>Cam Phaser Integrator Step (Retard)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Duty removed from the exhaust cam phaser&#x27;s integrator every 12.5 ms while the actual cam is past desired, by the size of the error (full scale about 1.6 deg). Stock 0.003 % for a tiny error to 0.12 % at full scale. Effect: raise = the cam phaser duty falls faster when the cam is past its target Evidence: ledger:E0670, ledger:E0737, ledger:E1226</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>fraction of 1.6 deg error</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.062" />
      <LABEL index="2" value="0.125" />
      <LABEL index="3" value="0.188" />
      <LABEL index="4" value="0.25" />
      <LABEL index="5" value="0.312" />
      <LABEL index="6" value="0.375" />
      <LABEL index="7" value="0.438" />
      <LABEL index="8" value="0.5" />
      <LABEL index="9" value="0.562" />
      <LABEL index="10" value="0.625" />
      <LABEL index="11" value="0.688" />
      <LABEL index="12" value="0.75" />
      <LABEL index="13" value="0.812" />
      <LABEL index="14" value="0.875" />
      <LABEL index="15" value="0.938" />
      <LABEL index="16" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22BAE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5E1" flags="0x30">
    <title>Cam Alternate Mode - Coolant Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam alternate mode: replaces the desired exhaust cam angle with this chain once engine speed reaches 8100 rpm in idle spark mode after 3 s of running. Multiplier by coolant temperature (-40 to 120 C). Stock 1.0 from 10 to 50 C, 0 otherwise. Dormant: the stock calibration never reaches that speed in idle spark mode, so it has no effect on this truck&#x27;s software. Effect: lower = less alternate mode cam angle at that coolant temperature Evidence: ledger:E0670, ledger:E0737, ledger:E1229</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22CD8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5E2" flags="0x30">
    <title>Cam Phasing Enable - RPM On Above vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phasing is allowed only while all of its enable conditions hold. The rpm condition turns on above this engine speed, by coolant temperature. Stock 1200 rpm up to 80 C, rising to 2800 rpm hot. Effect: raise = cam phasing needs more rpm at that coolant Evidence: ledger:E0738</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22D26" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5E3" flags="0x30">
    <title>Corrected Coolant Model - Start Delay vs Start-Up Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine revolutions after start during which the corrected coolant temperature stays at its start value, by coolant temperature at start. After this the warm-up rate curve raises it. Stock 3513 revolutions at -40 C, 1200 at 7.5 C, 100 from about 79 C. Effect: raise = the modelled coolant temperature stays at its start value for more engine revolutions Evidence: ledger:E0254, ledger:E0769, ledger:E1185</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28.125" />
      <LABEL index="2" value="-16.25" />
      <LABEL index="3" value="-4.375" />
      <LABEL index="4" value="7.5" />
      <LABEL index="5" value="19.375" />
      <LABEL index="6" value="31.25" />
      <LABEL index="7" value="43.125" />
      <LABEL index="8" value="55" />
      <LABEL index="9" value="66.875" />
      <LABEL index="10" value="78.75" />
      <LABEL index="11" value="90.625" />
      <LABEL index="12" value="102.5" />
      <LABEL index="13" value="114.375" />
      <LABEL index="14" value="126.25" />
      <LABEL index="15" value="138.125" />
      <LABEL index="16" value="150" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x239A4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>crank revolutions</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5E4" flags="0x30">
    <title>Corrected Coolant Model - Warm-Up Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the corrected coolant temperature rises after the start delay, in degrees per 1000 engine revolutions, by the modelled temperature itself. Stock 5.5 C per 1000 revolutions when cold, falling to 3.1 from about 100 C. Effect: raise = the modelled coolant temperature rises faster after the start delay Evidence: ledger:E0254, ledger:E0769, ledger:E1185</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28.125" />
      <LABEL index="2" value="-16.25" />
      <LABEL index="3" value="-4.375" />
      <LABEL index="4" value="7.5" />
      <LABEL index="5" value="19.375" />
      <LABEL index="6" value="31.25" />
      <LABEL index="7" value="43.125" />
      <LABEL index="8" value="55" />
      <LABEL index="9" value="66.875" />
      <LABEL index="10" value="78.75" />
      <LABEL index="11" value="90.625" />
      <LABEL index="12" value="102.5" />
      <LABEL index="13" value="114.375" />
      <LABEL index="14" value="126.25" />
      <LABEL index="15" value="138.125" />
      <LABEL index="16" value="150" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x239C8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC per 1000 revolutions</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>999.984741</max>
      <MATH equation="X/65.536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5E5" flags="0x30">
    <title>Crank Signal Filter - Minimum Time Between Teeth vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crank sensor noise filter: a crank tooth edge that arrives sooner than this after the previous accepted edge is ignored, by engine speed. Values of 30 us and below leave the timer check at its last setting and go to a separate input filter setting instead. Stock 391 us at 0 rpm, 195 us at 512 rpm, about a tenth of a tooth period, 16 us from 5632 rpm. Effect: raise = more noise rejected, but real teeth closer together than this would be missed Evidence: ledger:E0781, ledger:E1273, ledger:E1638</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23AB6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>us</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5E6" flags="0x30">
    <title>Reduced Engine Power - Throttle Area Limit vs Speed (Hard Acceleration)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While a throttle control fault is active (reduced engine power), the throttle opening is limited to this share of full throttle area, by vehicle speed, whenever the vehicle accelerates harder than its allowed rate; a term that grows with the extra acceleration is taken off the limit. Applies above 8 km/h. Stock 2.0 % at 0 km/h rising to 34.0 % at 80 km/h. Effect: raise = more throttle allowed under reduced engine power when the vehicle accelerates hard Evidence: ledger:E0781, ledger:E1866</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23DE2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5E7" flags="0x30">
    <title>Pedal Position - Rise Hysteresis vs Pedal</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal: amount the pedal must rise above the last value before the pedal position follows it, by pedal position (0 to 100 %). A falling pedal is followed at once. Stock 0.5 % (0 at the two ends). Effect: raise = small pedal movements upward are ignored Evidence: ledger:E1120</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24EEE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5E8" flags="0x30">
    <title>Purge Demand - Factor vs Manifold Vacuum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount: factor on the purge flow request, by manifold vacuum (0 to 80 kPa). The valve flows less at low vacuum, so the demand is raised there. Stock 1.32 at no vacuum falling to 1.0 from 50 kPa. Effect: raise = more purge valve opening at that manifold vacuum Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa manifold vacuum</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24F9C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5E9" flags="0x30">
    <title>EVAP Purge - Minimum Target vs System Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest EVAP purge target allowed at each system voltage, applied unless an EVAP test is running. Stock 0 up to 6 V, 23 % at 7.5 V, 11 % from 12 V up. Effect: raise = more purge at that system voltage Evidence: ledger:E0746</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>V</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1.5" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4.5" />
      <LABEL index="4" value="6" />
      <LABEL index="5" value="7.5" />
      <LABEL index="6" value="9" />
      <LABEL index="7" value="10.5" />
      <LABEL index="8" value="12" />
      <LABEL index="9" value="13.5" />
      <LABEL index="10" value="15" />
      <LABEL index="11" value="16.5" />
      <LABEL index="12" value="18" />
      <LABEL index="13" value="19.5" />
      <LABEL index="14" value="21" />
      <LABEL index="15" value="22.5" />
      <LABEL index="16" value="24" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25100" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.781250</max>
      <MATH equation="X/326.4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5EA" flags="0x30">
    <title>Purge O2 Feedback - Factor Maximum vs Intake Air Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: highest value of the purge factor, by intake air temperature (-40 to 152 C). Stock 0.8 cold, 1.0 from 8 to 68 C, falling to 0.25 at 152 C. Effect: raise = more purge is allowed at that intake air temperature Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC intake air</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2513A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5EB" flags="0x30">
    <title>Purge O2 Feedback - Rich Time Before Fast Step vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: time the mixture must stay rich before the fast step and period are used, by engine airflow (0 to 128 g/s). Stock 0.6 s up to 32 g/s, 0.4 s above. Effect: raise = the fast cut back starts later Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>g/s airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="8" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="24" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="48" />
      <LABEL index="7" value="56" />
      <LABEL index="8" value="64" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="88" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="104" />
      <LABEL index="14" value="112" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2515E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5EC" flags="0x30">
    <title>Purge Flow - Reference Flow vs Manifold Vacuum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge: flow the purge valve can pass at each manifold vacuum (0 to 80 kPa). Long term fuel trim uses it to scale the purge learned correction. Stock 0 at no vacuum rising to 123 from 70 kPa. Purge flow units: the full scale word (stock 123) is full purge reference flow. Effect: raise = the fuel trim side assumes more purge flow at that vacuum Evidence: ledger:E1122</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa manifold vacuum</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x251CA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flow units</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5ED" flags="0x30">
    <title>Purge Amount - Factor Cap vs Fuel Tank Vacuum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount: after the EVAP leak test has finished for the trip, the purge factor is limited to this when fuel tank vacuum stays high for the tank vacuum cap time, by tank vacuum (-32 to +32 inH2O, positive = vacuum). Stock 1.0 up to 8 inH2O, 0.5 at 12 inH2O and 0 from 16 inH2O: purge stops before it pulls the tank down further. Effect: raise = more purge is allowed at that tank vacuum Evidence: ledger:E1123</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>inH2O tank vacuum</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-32" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-20" />
      <LABEL index="4" value="-16" />
      <LABEL index="5" value="-12" />
      <LABEL index="6" value="-8" />
      <LABEL index="7" value="-4" />
      <LABEL index="8" value="0" />
      <LABEL index="9" value="4" />
      <LABEL index="10" value="8" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="16" />
      <LABEL index="13" value="20" />
      <LABEL index="14" value="24" />
      <LABEL index="15" value="28" />
      <LABEL index="16" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25200" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5EE" flags="0x30">
    <title>Crank to Run Fuel Blend Rate vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the engine starts, the base fuel amount moves from the cranking fuel amount (the one shaped by Base Fuel Multiplier vs RPM) to the normal running amount. This is the fraction of that change made each update, by coolant temperature; the move is complete when the total reaches 1.0. Stock 0.05 up to 2 C, 0.07 at 14 C and 0.10 from 26 C. Effect: raise = fueling reaches the normal running amount sooner after a start Evidence: ledger:E0670, ledger:E0969</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x26CE4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x255DC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5EF" flags="0x30">
    <title>Acceleration Fuel Adder - Decay vs Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra fuel on acceleration: share of the adder that is kept at each update (each injection event of the cylinder), by port temperature. Stock 0.73 cold, 0.30 hot. No effect while the adder gain is 0, as on the stock calibration. Effect: raise = the extra fuel fades out more slowly Evidence: ledger:E1127</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (port temp model)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-24" />
      <LABEL index="2" value="-8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="24" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="56" />
      <LABEL index="7" value="72" />
      <LABEL index="8" value="88" />
      <LABEL index="9" value="104" />
      <LABEL index="10" value="120" />
      <LABEL index="11" value="136" />
      <LABEL index="12" value="152" />
      <LABEL index="13" value="168" />
      <LABEL index="14" value="184" />
      <LABEL index="15" value="200" />
      <LABEL index="16" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2670A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5F0" flags="0x30">
    <title>Transient Fuel Model Temperature vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest temperature the transient fuel (wall wetting) model uses, by coolant temperature (-40 to 152 C). The model takes the higher of this and the coolant based temperature. Stock equal to coolant up to 80 C, then 120 C at 92 C rising to 155 C from 128 C. Effect: raise = the transient fuel model treats the ports as hotter at that coolant temperature Evidence: ledger:E0670, ledger:E0937, ledger:E1224</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AB62" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5F1" flags="0x30">
    <title>Transient Fuel Model - Hot Restart Temperature Carry-Over</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the transient (wall-wetting) fuel model starts, its temperature starts between the current coolant temperature and the hotter temperature it had when the engine was shut off. This is the fraction of that difference kept, by engine-off time (0 to 512 s). Stock 1.0 right after shut-off, 0.5 at 32 s, 0.25 at 96 s and 0 from 256 s. Effect: raise = a hot restart is treated as hotter for longer Evidence: ledger:E0670, ledger:E0965</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>s (engine-off time)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="32" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="96" />
      <LABEL index="4" value="128" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="192" />
      <LABEL index="7" value="224" />
      <LABEL index="8" value="256" />
      <LABEL index="9" value="288" />
      <LABEL index="10" value="320" />
      <LABEL index="11" value="352" />
      <LABEL index="12" value="384" />
      <LABEL index="13" value="416" />
      <LABEL index="14" value="448" />
      <LABEL index="15" value="480" />
      <LABEL index="16" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AB86" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5F2" flags="0x0">
    <title>Tip-In Spark Advance - RPM Factor Coolant Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in spark advance: the engine speed factor is applied to the advance only when coolant is above this and the run time condition is met. Stock -40 C. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = the speed factor is skipped on a colder engine Evidence: ledger:E1142</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2CD56" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5F3" flags="0x0">
    <title>Tip-In Spark Advance - RPM Factor Run Time Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in spark advance: the engine speed factor is applied to the advance only after the engine has run longer than this. Stock 5 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = the speed factor is skipped for longer after a start Evidence: ledger:E1142</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2CD58" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5F4" flags="0x30">
    <title>EVAP Engine-Off Test - Vent Open Time vs Ambient Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: how long the vent stays open at the start of the test before the pressure phase begins, by ambient air temperature. Stock 30 s when cold rising to 500 s when hot. Effect: raise = the tank is vented longer before the test starts measuring Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (ambient air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-10" />
      <LABEL index="1" value="-4.375" />
      <LABEL index="2" value="1.25" />
      <LABEL index="3" value="6.875" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.125" />
      <LABEL index="6" value="23.75" />
      <LABEL index="7" value="29.375" />
      <LABEL index="8" value="35" />
      <LABEL index="9" value="40.625" />
      <LABEL index="10" value="46.25" />
      <LABEL index="11" value="51.875" />
      <LABEL index="12" value="57.5" />
      <LABEL index="13" value="63.125" />
      <LABEL index="14" value="68.75" />
      <LABEL index="15" value="74.375" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33FF0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5F5" flags="0x30">
    <title>EVAP Engine-Off Test - Vent Open Time vs Ambient Temperature (service test)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the same vent-open time for the scan tool started version of the test while its ambient temperature estimate is not yet valid. Stock equal to the normal curve. Effect: raise = the tank is vented longer before the service test starts measuring Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (ambient air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-10" />
      <LABEL index="1" value="-4.375" />
      <LABEL index="2" value="1.25" />
      <LABEL index="3" value="6.875" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.125" />
      <LABEL index="6" value="23.75" />
      <LABEL index="7" value="29.375" />
      <LABEL index="8" value="35" />
      <LABEL index="9" value="40.625" />
      <LABEL index="10" value="46.25" />
      <LABEL index="11" value="51.875" />
      <LABEL index="12" value="57.5" />
      <LABEL index="13" value="63.125" />
      <LABEL index="14" value="68.75" />
      <LABEL index="15" value="74.375" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34014" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5F6" flags="0x30">
    <title>Fuel Trim Monitor - Purge Ramp Up Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): amount commanded purge is raised every 100 ms when purge is restored after the measurement, by the normal purge command (0 to 100 %). Stock 0.5 % per step up to 25 % purge, 5 % at 31 %, 10 % above. Effect: raise = purge returns faster after the test Evidence: ledger:E0670, ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% commanded purge</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.275" />
      <LABEL index="2" value="12.55" />
      <LABEL index="3" value="18.825" />
      <LABEL index="4" value="25.1" />
      <LABEL index="5" value="31.375" />
      <LABEL index="6" value="37.65" />
      <LABEL index="7" value="43.925" />
      <LABEL index="8" value="50.2" />
      <LABEL index="9" value="56.475" />
      <LABEL index="10" value="62.75" />
      <LABEL index="11" value="69.025" />
      <LABEL index="12" value="75.3" />
      <LABEL index="13" value="81.575" />
      <LABEL index="14" value="87.85" />
      <LABEL index="15" value="94.125" />
      <LABEL index="16" value="100.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x363A4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% per step</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.781250</max>
      <MATH equation="X/326.4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5F7" flags="0x30">
    <title>Airflow Rationality - Throttle Flow Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101), diagnostic model only: flow factor of the throttle airflow model by the ratio of manifold pressure to barometric pressure (0.5 to 0.99). Stock follows the ideal gas flow function: 0.685 at a ratio of 0.5 and below, falling to 0.141 at 0.99. Effect: raise = the model expects more airflow through the throttle at that pressure ratio Evidence: ledger:E0772, ledger:E1074</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>pressure ratio</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.500" />
      <LABEL index="1" value="0.531" />
      <LABEL index="2" value="0.561" />
      <LABEL index="3" value="0.592" />
      <LABEL index="4" value="0.622" />
      <LABEL index="5" value="0.653" />
      <LABEL index="6" value="0.684" />
      <LABEL index="7" value="0.714" />
      <LABEL index="8" value="0.745" />
      <LABEL index="9" value="0.776" />
      <LABEL index="10" value="0.806" />
      <LABEL index="11" value="0.837" />
      <LABEL index="12" value="0.867" />
      <LABEL index="13" value="0.898" />
      <LABEL index="14" value="0.929" />
      <LABEL index="15" value="0.959" />
      <LABEL index="16" value="0.990" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36712" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5F8" flags="0x30">
    <title>Airflow-Weighted Intake Temperature Blend Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 16-point curve indexed by airflow. Each cell is a fraction, from 0 to 1.0, that blends the intake air temperature reading toward coolant temperature: 0 keeps the raw intake reading, 1.0 uses coolant temperature entirely. This compensates for heat soak, when the intake air sensor reads artificially hot right after a hot engine is shut off and restarted with little airflow to clear it. The blended temperature feeds an air density correction inside the engine&#x27;s airflow estimate. Stock blend fraction ranges from about 0.20 to 0.71 across the airflow range, leaning further toward coolant temperature at low airflow. Effect: ra...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>16</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B198" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction (Q15: 32768 = weight of 1.0)</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5F9" flags="0x30">
    <title>Cam Alternate Mode - Barometric Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam alternate mode: replaces the desired exhaust cam angle with this chain once engine speed reaches 8100 rpm in idle spark mode after 3 s of running. Multiplier by barometric pressure (60 to 100 kPa). Stock 0 to 65 kPa, 0.25 at 70 kPa, 0.5 at 75, 0.75 at 80, 1.0 from 85 kPa. Dormant: the stock calibration never reaches that speed in idle spark mode, so it has no effect on this truck&#x27;s software. Effect: lower = less alternate mode cam angle at that barometric pressure Evidence: ledger:E0670, ledger:E0737, ledger:E1229</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="60" />
      <LABEL index="1" value="65" />
      <LABEL index="2" value="70" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="80" />
      <LABEL index="5" value="85" />
      <LABEL index="6" value="90" />
      <LABEL index="7" value="95" />
      <LABEL index="8" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22CC4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5FA" flags="0x30">
    <title>Cam Phasing Enable - Minimum Run Time vs Start-Up Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phasing is allowed only while all of its enable conditions hold. This one: the engine must have run for at least this long since start, by the coolant temperature at start-up. Stock 120 s when starting below about -16 C, 18 s from 8 to 56 C, 5 s at 80 to 104 C, 8 to 12 s when hotter. Effect: raise = cam phasing starts later after a start Evidence: ledger:E0769, ledger:E0970</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (start-up coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22D04" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5FB" flags="0x30">
    <title>Charge Temperature - Filter Speed vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Charge temperature model (used by the VE airflow model and the VE Maximum airmass cap): the charge temperature moves toward intake air temperature plus a fraction of the coolant-to-intake difference, the fraction set by airflow (more airflow, closer to intake temperature), through a lag filter whose speed is also set by airflow. This is the filter speed per update. Stock 0.07 at zero airflow up to 0.57 at 128 g/s. Effect: raise = charge temperature follows changes faster Evidence: ledger:E0670, ledger:E0878</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s (airflow)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2310A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5FC" flags="0x30">
    <title>Engine Start Detection RPM vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM decides the engine has started (cranking is over and it is running) once engine speed has stayed at or above this for the number of updates in Engine Start Detection Count, by coolant temperature. Stock 575 rpm up to about 8 C, 550 rpm from about 31 C. Effect: raise = the engine must spin faster before it counts as started Evidence: ledger:E0768, ledger:E0966</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16.25" />
      <LABEL index="2" value="7.5" />
      <LABEL index="3" value="31.25" />
      <LABEL index="4" value="55" />
      <LABEL index="5" value="78.75" />
      <LABEL index="6" value="102.5" />
      <LABEL index="7" value="126.25" />
      <LABEL index="8" value="150" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23A56" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5FD" flags="0x30">
    <title>Engine Start Detection Count vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How many updates in a row engine speed must stay at or above Engine Start Detection RPM before the PCM decides the engine has started, by coolant temperature. Stock 8 at -40 C, 6 at -16 C, 4 from about 8 C. Effect: raise = the engine must hold start speed longer Evidence: ledger:E0768, ledger:E0966</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16.25" />
      <LABEL index="2" value="7.5" />
      <LABEL index="3" value="31.25" />
      <LABEL index="4" value="55" />
      <LABEL index="5" value="78.75" />
      <LABEL index="6" value="102.5" />
      <LABEL index="7" value="126.25" />
      <LABEL index="8" value="150" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23A6A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>updates</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5FE" flags="0x30">
    <title>A/C Idle Air - Second Stage Delay vs A/C Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the staged A/C idle air sequence, after the first step of extra idle air has ramped in, the PCM waits this many engine reference periods (one period is the time between two cylinder firings, so the wait gets shorter as rpm rises) before the second stage starts; the A/C clutch is held off until the sequence ends. By A/C compressor torque (0 to 80 Nm). Stock 5 periods at 0 Nm rising to 25 periods at 80 Nm. Effect: raise = longer wait between the two stages of A/C idle air before the A/C engages Evidence: ledger:E0670, ledger:E1870</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>Nm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29E86" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>reference periods</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5FF" flags="0x30">
    <title>Idle Airflow - Shortfall Add-On vs Airflow Shortfall</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra idle airflow added when measured airflow falls short of the predicted idle airflow, by the size of the shortfall (0 to 4 g/s). The detector that would use it cannot arm on this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0289, ledger:E0670, ledger:E0936, ledger:E1187</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s (predicted minus measured airflow)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.5" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="1.5" />
      <LABEL index="4" value="2" />
      <LABEL index="5" value="2.5" />
      <LABEL index="6" value="3" />
      <LABEL index="7" value="3.5" />
      <LABEL index="8" value="4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A7CC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x600" flags="0x30">
    <title>Idle Airflow - Shortfall Add-On, Second Term (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Second term added to the idle airflow shortfall add-on. The software feeds this table a fixed zero input, so only its first point is ever used, and that point is 0 on stock (the remaining points, 0.125 to 1.0 g/s, are never reached). Dormant: no effect on this truck&#x27;s software. Effect: raising the first point adds that airflow whenever the shortfall add-on runs; the other points are never used Evidence: ledger:E0670, ledger:E0936, ledger:E1187, ledger:E1241</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A7E0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x601" flags="0x30">
    <title>Burst Knock Retard - Multiplier vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant factor on the burst knock retard, alongside its intake temperature and rpm multipliers (1.0 = full retard). Lower = less burst knock retard at that coolant temperature. Effect: raise = more burst knock retard at that coolant Evidence: ledger:E0759</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AD36" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x602" flags="0x30">
    <title>Burst Knock Retard Multiplier vs Coolant, Per-Bank</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A curve, indexed by coolant temperature from -40 to 152 degrees Celsius over 9 points, that scales how much a per-bank rolling maximum burst-knock-retard value is updated each pass. Stock ranges from a multiplier of 0.20 at the coldest point to about 1.00 once the engine is warm. Effect: Raising a point increases how much the coolant-based multiplier contributes when updating that bank&#x27;s rolling burst-knock-retard maximum at that temperature; lowering it reduces that contribution. Evidence: ledger:E0772, ledger:E0805</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AD76" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain (Q16, unitless)</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x603" flags="0x30">
    <title>Knock Learn Rate - MAP Curve</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is the MAP curve. Effect: raise = faster knock learning for under-sampled cylinders there Evidence: ledger:E0193, ledger:E0772, ledger:E0871</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="20" />
      <LABEL index="1" value="30" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="50" />
      <LABEL index="4" value="60" />
      <LABEL index="5" value="70" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="90" />
      <LABEL index="8" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AEA4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x604" flags="0x30">
    <title>Knock Learn Rate - Coolant Curve</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is the coolant temperature curve. Effect: raise = faster knock learning for under-sampled cylinders there Evidence: ledger:E0193, ledger:E0772, ledger:E0871</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AECE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x605" flags="0x30">
    <title>Knock Learn Rate - Intake Temperature Curve</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is the intake temperature curve. Effect: raise = faster knock learning for under-sampled cylinders there Evidence: ledger:E0193, ledger:E0772, ledger:E0871</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC intake air</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AEE2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x606" flags="0x30">
    <title>Torque Reduction Spark Retard - Maximum vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque reduction: largest spark retard a torque reduction may request, by coolant temperature. Stock 20, 30 and 40 degrees at -40, -20 and 0 C and 50 degrees from 20 C up. Effect: lower = less spark retard is available to a torque reduction at that temperature Evidence: ledger:E1130</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31906" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x607" flags="0x30">
    <title>Cold Off-Idle Spark Retard - Coolant Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier on the cold off-idle spark retard table by coolant temperature (128 = 1.0). Stock 1.0 up to 60 C, 0.5 at 70 C and 0 from 80 C, so the retard only acts on a cold engine. Effect: raise = keep more of the cold off-idle spark retard at that coolant temperature Evidence: ledger:E0670, ledger:E1181</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2D0C4" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x608" flags="0x30">
    <title>Tip-In Spark Advance - Trigger Factor vs Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in spark advance (spark advance added for a short time when cylinder airmass jumps): the advance triggers when cylinder airmass rises in one 12.5 ms pass by at least 1.024 g per cylinder x the three trigger factors (engine speed, coolant, throttle). This is the throttle factor. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: lower = the advance triggers on a smaller airmass jump Evidence: ledger:E1142</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>% throttle area above idle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CD90" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x609" flags="0x30">
    <title>Purge Amount - Hot Restart Factor vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount: during a hot restart, before normal purge is enabled, a small purge flow is requested by time since the start; this curve scales it by engine airflow (0 to 80 g/s). Stock 1.0 everywhere. Effect: lower = less purge during a hot restart at that airflow Evidence: ledger:E1121</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="2.5" />
      <LABEL index="2" value="5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="10" />
      <LABEL index="5" value="12.5" />
      <LABEL index="6" value="15" />
      <LABEL index="7" value="17.5" />
      <LABEL index="8" value="20" />
      <LABEL index="9" value="22.5" />
      <LABEL index="10" value="25" />
      <LABEL index="11" value="27.5" />
      <LABEL index="12" value="30" />
      <LABEL index="13" value="32.5" />
      <LABEL index="14" value="35" />
      <LABEL index="15" value="37.5" />
      <LABEL index="16" value="40" />
      <LABEL index="17" value="42.5" />
      <LABEL index="18" value="45" />
      <LABEL index="19" value="47.5" />
      <LABEL index="20" value="50" />
      <LABEL index="21" value="52.5" />
      <LABEL index="22" value="55" />
      <LABEL index="23" value="57.5" />
      <LABEL index="24" value="60" />
      <LABEL index="25" value="62.5" />
      <LABEL index="26" value="65" />
      <LABEL index="27" value="67.5" />
      <LABEL index="28" value="70" />
      <LABEL index="29" value="72.5" />
      <LABEL index="30" value="75" />
      <LABEL index="31" value="77.5" />
      <LABEL index="32" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x252B4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x60A" flags="0x30">
    <title>O2 Response Test (P0133) - Max Average Lean-to-Rich Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0133 sets if the average lean-to-rich transition time (350 to 650 mV) is above this. Stock 200 ms. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: raise = a slower sensor still passes Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x347D2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ms</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>63999.023438</max>
      <MATH equation="X/1.024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x60B" flags="0x30">
    <title>O2 Response Test (P1133) - Min Lean-to-Rich Transitions</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1133 sets if fewer lean-to-rich transitions than this are timed in the test. Stock 4. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: raise = the test needs more complete transitions to pass Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x347FE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>count</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x60C" flags="0x30">
    <title>O2 Response Test (P0133) - Max Average Rich-to-Lean Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0133 sets if the average rich-to-lean transition time (650 to 350 mV) is above this. Stock 200 ms. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: raise = a slower sensor still passes Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3482A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ms</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>63999.023438</max>
      <MATH equation="X/1.024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x60D" flags="0x30">
    <title>O2 Response Test (P1133) - Min Rich-to-Lean Transitions</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1133 sets if fewer rich-to-lean transitions than this are timed in the test. Stock 4. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: raise = the test needs more complete transitions to pass Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34856" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>count</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x60E" flags="0x30">
    <title>O2 Response Test (P1134) - Max Time Ratio (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Used only by the ratio form of the P1134 test, which stock does not select (the difference form above is used). Stock 7.0. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: no effect on stock (inactive) Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34882" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x60F" flags="0x30">
    <title>O2 Response Test - Min Lean-to-Rich Transitions, Second Sensor (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Copy of the sensor 1 limit for a second front O2 sensor. The H3 tests one sensor, so this is never used. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: no effect on stock (inactive) Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3495E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>count</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x610" flags="0x30">
    <title>O2 Response Test - Min Rich-to-Lean Transitions, Second Sensor (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Copy of the sensor 1 limit for a second front O2 sensor. The H3 tests one sensor, so this is never used. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: no effect on stock (inactive) Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x349B6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>count</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x611" flags="0x30">
    <title>O2 Response Test - Max Time Ratio, Second Sensor (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Copy of the sensor 1 limit for a second front O2 sensor. The H3 tests one sensor, so this is never used. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: no effect on stock (inactive) Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x349E2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x612" flags="0x30">
    <title>O2 Response Test - Min Rich Switches, Second Sensor (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Copy of the sensor 1 limit for a second front O2 sensor. The H3 tests one sensor, so this is never used. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: no effect on stock (inactive) Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34A3A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>count</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x613" flags="0x30">
    <title>O2 Response Test - Min Lean Switches, Second Sensor (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Copy of the sensor 1 limit for a second front O2 sensor. The H3 tests one sensor, so this is never used. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: no effect on stock (inactive) Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34A66" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>count</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x614" flags="0x30">
    <title>O2 Response Test (P1134) - Max Time Difference</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1134 sets if the average rich-to-lean time minus the average lean-to-rich time is above this. Stock 90 ms. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: raise = a larger imbalance still passes Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34A92" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>ms</units>
      <decimalpl>1</decimalpl>
      <min>-32000.000000</min>
      <max>31999.023438</max>
      <MATH equation="X/1.024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x615" flags="0x30">
    <title>O2 Response Test (P1134) - Min Time Difference</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1134 sets if the average rich-to-lean time minus the average lean-to-rich time is below this. Stock -65 ms. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: lower = a larger imbalance still passes Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34AEA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>ms</units>
      <decimalpl>1</decimalpl>
      <min>-32000.000000</min>
      <max>31999.023438</max>
      <MATH equation="X/1.024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x616" flags="0x30">
    <title>Pedal Filter Factor vs Engine Run Time (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal filter factor by engine run time (0 to 200 s). Stock 1.0. The filter takes the largest of four terms: the run time, coolant and coolant above intake air factors multiplied together, the vehicle speed factor, a wheel acceleration factor and an axle torque factor. A factor of 1.0 gives the slowest filter (the pedal filter gain); lower makes the filter faster. On the stock file the last two terms are fixed at 1.0, so this curve has no effect. Effect: no effect on the stock file Evidence: ledger:E0768, ledger:E0945, ledger:E1118</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>s (engine run time)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="12.5" />
      <LABEL index="2" value="25" />
      <LABEL index="3" value="37.5" />
      <LABEL index="4" value="50" />
      <LABEL index="5" value="62.5" />
      <LABEL index="6" value="75" />
      <LABEL index="7" value="87.5" />
      <LABEL index="8" value="100" />
      <LABEL index="9" value="112.5" />
      <LABEL index="10" value="125" />
      <LABEL index="11" value="137.5" />
      <LABEL index="12" value="150" />
      <LABEL index="13" value="162.5" />
      <LABEL index="14" value="175" />
      <LABEL index="15" value="187.5" />
      <LABEL index="16" value="200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24E0A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x617" flags="0x30">
    <title>Pedal Filter Factor vs Coolant Temperature (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal filter factor by coolant temperature, taken before the engine starts. Stock 1.0. The filter takes the largest of four terms: the run time, coolant and coolant above intake air factors multiplied together, the vehicle speed factor, a wheel acceleration factor and an axle torque factor. A factor of 1.0 gives the slowest filter (the pedal filter gain); lower makes the filter faster. On the stock file the last two terms are fixed at 1.0, so this curve has no effect. Effect: no effect on the stock file Evidence: ledger:E0768, ledger:E0945, ledger:E1118</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24E2E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x618" flags="0x30">
    <title>Pedal Filter Factor vs Vehicle Speed (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal filter factor by vehicle speed (0 to 128 km/h). Stock 1.0. The filter takes the largest of four terms: the run time, coolant and coolant above intake air factors multiplied together, the vehicle speed factor, a wheel acceleration factor and an axle torque factor. A factor of 1.0 gives the slowest filter (the pedal filter gain); lower makes the filter faster. On the stock file the last two terms are fixed at 1.0, so this curve has no effect. Effect: no effect on the stock file Evidence: ledger:E0768, ledger:E0945, ledger:E1118</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="8" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="24" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="48" />
      <LABEL index="7" value="56" />
      <LABEL index="8" value="64" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="88" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="104" />
      <LABEL index="14" value="112" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24E66" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x619" flags="0x30">
    <title>Pedal Filter Factor vs Driveline Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal filter factor by driveline output torque (engine torque through converter, gear and final drive, 0 to 8192 Nm). This is the axle torque factor: the filter takes the largest of the fade terms, and a factor of 1.0 gives the slowest filter (the pedal filter gain); lower makes the filter faster. Stock 1.0 everywhere, which holds the largest term at 1.0, so the other pedal filter factor curves have no effect on the stock file. Effect: lower = faster pedal filter at that torque, once no other term is higher Evidence: ledger:E0781, ledger:E0991, ledger:E1203</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>Nm (driveline output torque)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24EC6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x61A" flags="0x30">
    <title>EVAP Engine-Off Test - Pressure Peak Factor vs Vapour Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: factor on the pressure peak stored at the end of the pressure phase, by fuel vapour temperature. Stock 1.0 everywhere. Effect: lower = the pressure peak counts for less at that vapour temperature Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (fuel vapour)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-10" />
      <LABEL index="1" value="-4.375" />
      <LABEL index="2" value="1.25" />
      <LABEL index="3" value="6.875" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.125" />
      <LABEL index="6" value="23.75" />
      <LABEL index="7" value="29.375" />
      <LABEL index="8" value="35" />
      <LABEL index="9" value="40.625" />
      <LABEL index="10" value="46.25" />
      <LABEL index="11" value="51.875" />
      <LABEL index="12" value="57.5" />
      <LABEL index="13" value="63.125" />
      <LABEL index="14" value="68.75" />
      <LABEL index="15" value="74.375" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33FA8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x61B" flags="0x30">
    <title>EVAP Engine-Off Test - Pressure Peak Factor vs Vapour Temperature Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: factor on the pressure peak stored at the end of the pressure phase, by how much the fuel vapour temperature rose during the phase. Stock 1.0 everywhere. Effect: lower = the pressure peak counts for less at that temperature rise Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (fuel vapour rise)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.625" />
      <LABEL index="2" value="1.25" />
      <LABEL index="3" value="1.875" />
      <LABEL index="4" value="2.5" />
      <LABEL index="5" value="3.125" />
      <LABEL index="6" value="3.75" />
      <LABEL index="7" value="4.375" />
      <LABEL index="8" value="5" />
      <LABEL index="9" value="5.625" />
      <LABEL index="10" value="6.25" />
      <LABEL index="11" value="6.875" />
      <LABEL index="12" value="7.5" />
      <LABEL index="13" value="8.125" />
      <LABEL index="14" value="8.75" />
      <LABEL index="15" value="9.375" />
      <LABEL index="16" value="10" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33FCC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x61C" flags="0x30">
    <title>Misfire - Minimum Load Coolant Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: multiplier of the minimum load curve by coolant temperature (-40 to 151 C). Stock 1.0 at every temperature. Effect: raise = the minimum load is higher at that coolant temperature Evidence: ledger:E0670, ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>16</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-27.25" />
      <LABEL index="2" value="-14.5" />
      <LABEL index="3" value="-1.75" />
      <LABEL index="4" value="11" />
      <LABEL index="5" value="23.75" />
      <LABEL index="6" value="36.5" />
      <LABEL index="7" value="49.25" />
      <LABEL index="8" value="62" />
      <LABEL index="9" value="74.75" />
      <LABEL index="10" value="87.5" />
      <LABEL index="11" value="100.25" />
      <LABEL index="12" value="113" />
      <LABEL index="13" value="125.75" />
      <LABEL index="14" value="138.5" />
      <LABEL index="15" value="151.25" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37052" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x61D" flags="0x30">
    <title>Knock Learn Rate - Sample Count Curve</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is the sample count curve. Effect: raise = faster knock learning for under-sampled cylinders there Evidence: ledger:E0193, ledger:E0772, ledger:E0871</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>count (learn samples)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2560" />
      <LABEL index="1" value="6400" />
      <LABEL index="2" value="10240" />
      <LABEL index="3" value="14080" />
      <LABEL index="4" value="17920" />
      <LABEL index="5" value="21760" />
      <LABEL index="6" value="25600" />
      <LABEL index="7" value="29440" />
      <LABEL index="8" value="33280" />
      <LABEL index="9" value="37120" />
      <LABEL index="10" value="40960" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AEF6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x61E" flags="0x30">
    <title>Knock Learn Rate - Engine Speed Curve</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is the engine speed curve. Effect: raise = faster knock learning for under-sampled cylinders there Evidence: ledger:E0193, ledger:E0772, ledger:E0871</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="800" />
      <LABEL index="1" value="1600" />
      <LABEL index="2" value="2400" />
      <LABEL index="3" value="3200" />
      <LABEL index="4" value="4000" />
      <LABEL index="5" value="4800" />
      <LABEL index="6" value="5600" />
      <LABEL index="7" value="6400" />
      <LABEL index="8" value="7200" />
      <LABEL index="9" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AEB8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x61F" flags="0x30">
    <title>Pedal Gain Reduction - Confirm Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the truck must accelerate at or above the pedal gain reduction acceleration threshold before the reduction starts, by driveline output torque (0 to 648 Nm). Stock 3200 s, so in effect never. Effect: lower = the pedal gain reduction starts sooner once the acceleration threshold is met Evidence: ledger:E0217, ledger:E0781, ledger:E1203</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>Nm (driveline output torque)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="81" />
      <LABEL index="2" value="162" />
      <LABEL index="3" value="243" />
      <LABEL index="4" value="324" />
      <LABEL index="5" value="405" />
      <LABEL index="6" value="486" />
      <LABEL index="7" value="567" />
      <LABEL index="8" value="648" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23EB0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x620" flags="0x30">
    <title>Pedal Filter Factor vs Coolant Above Intake Air (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal filter factor by how far coolant is above intake air temperature (0 to 96 C). Stock 1.0. The filter takes the largest of four terms: the run time, coolant and coolant above intake air factors multiplied together, the vehicle speed factor, a wheel acceleration factor and an axle torque factor. A factor of 1.0 gives the slowest filter (the pedal filter gain); lower makes the filter faster. On the stock file the last two terms are fixed at 1.0, so this curve has no effect. Effect: no effect on the stock file Evidence: ledger:E0768, ledger:E0946, ledger:E1118</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (coolant above intake air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="12" />
      <LABEL index="2" value="24" />
      <LABEL index="3" value="36" />
      <LABEL index="4" value="48" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="72" />
      <LABEL index="7" value="84" />
      <LABEL index="8" value="96" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24E52" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x621" flags="0x30">
    <title>Accelerator Pedal Filter - Fade Weight vs Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight on the largest fade term (run time, coolant, speed and other factors) before it is taken off the tracked filter gain, by that gain (0 to 100 %). Stock 1.0. Part of the accelerator pedal filter: the filtered pedal closes this share of its gap to the pedal demand every update; 1.0 follows the pedal at once. Effect: lower = the fade terms reduce the filter gain less at that gain Evidence: ledger:E0330, ledger:E0781, ledger:E1190</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>% (tracked gain)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="12.5" />
      <LABEL index="2" value="25" />
      <LABEL index="3" value="37.5" />
      <LABEL index="4" value="50" />
      <LABEL index="5" value="62.5" />
      <LABEL index="6" value="75" />
      <LABEL index="7" value="87.5" />
      <LABEL index="8" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24EB2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x622" flags="0x30">
    <title>EVAP Purge - Ramp Rate Falling, Highway</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the gap to the purge target closed on each purge update (about a tenth of a second) when commanded purge is falling at or above the speed split, by airflow. Stock 99.9 % (near instant). Effect: raise = purge follows its target faster Evidence: ledger:E0739, ledger:E1124</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2509A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x623" flags="0x30">
    <title>EVAP Purge - Ramp Rate Rising, Highway</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the gap to the purge target closed on each purge update (about a tenth of a second) when commanded purge is rising at or above the speed split, by airflow. Stock 99.9 % (near instant). Effect: raise = purge follows its target faster Evidence: ledger:E0739, ledger:E1124</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x250AE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x624" flags="0x30">
    <title>LTFT Follow Rate vs MAP Change</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: how fast the applied long term trim moves to the value of the current cell, as the fraction of the gap closed every 12.5 ms, by the change of manifold pressure (-4 to +4 kPa against its filtered value). Stock 1.0 everywhere: the applied trim follows the cell at once. Effect: lower = the applied trim moves to a new cell value more gradually Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa MAP change</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-4" />
      <LABEL index="1" value="-3" />
      <LABEL index="2" value="-2" />
      <LABEL index="3" value="-1" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="1" />
      <LABEL index="6" value="2" />
      <LABEL index="7" value="3" />
      <LABEL index="8" value="4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25784" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x625" flags="0x30">
    <title>Idle Base Airflow - Baro Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air control: factor on the base idle airflow by barometric pressure (60 to 100 kPa). Stock 1.0 everywhere. Effect: raise = more base idle air at that barometric pressure Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="60" />
      <LABEL index="1" value="65" />
      <LABEL index="2" value="70" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="80" />
      <LABEL index="5" value="85" />
      <LABEL index="6" value="90" />
      <LABEL index="7" value="95" />
      <LABEL index="8" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2954A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x626" flags="0x30">
    <title>Idle Airflow - Light-Off Retard Adder Coolant Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the idle air added for catalyst light-off spark retard, by coolant temperature (-40 to 152 C). Stock 1.0 everywhere. Effect: lower = less light-off idle air at that coolant temperature Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29F46" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x627" flags="0x30">
    <title>Spark Ceiling - Hot Mode Hold Airmass vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once armed, the hot high-load spark ceiling stays active while cylinder airmass is above this curve. Stock 0.65 g/cyl at every rpm. Effect: raise = the ceiling drops out at a higher load Evidence: ledger:E0719</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1600" />
      <LABEL index="1" value="2400" />
      <LABEL index="2" value="3200" />
      <LABEL index="3" value="4000" />
      <LABEL index="4" value="4800" />
      <LABEL index="5" value="5600" />
      <LABEL index="6" value="6400" />
      <LABEL index="7" value="7200" />
      <LABEL index="8" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30242" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/cyl</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8.191875</max>
      <MATH equation="X/8000"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x628" flags="0x30">
    <title>Spark Ceiling - Hot Mode Entry Airmass vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The hot high-load spark ceiling starts arming only while cylinder airmass is above this curve. Stock 0.67 g/cyl at every rpm. Effect: raise = the ceiling arms only at higher load Evidence: ledger:E0719</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1600" />
      <LABEL index="1" value="2400" />
      <LABEL index="2" value="3200" />
      <LABEL index="3" value="4000" />
      <LABEL index="4" value="4800" />
      <LABEL index="5" value="5600" />
      <LABEL index="6" value="6400" />
      <LABEL index="7" value="7200" />
      <LABEL index="8" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30256" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/cyl</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8.191875</max>
      <MATH equation="X/8000"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x629" flags="0x30">
    <title>Shift Lamp - Pedal Limit Hysteresis by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift lamp request (a data bus signal for a manual transmission upshift lamp): while the lamp is off, the pedal limit of each gear is lowered by this (times the barometric factor), so the lamp does not flicker at the limit. Stock 5 % in first gear, 10 % in the others. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E1143</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="5th" />
      <LABEL index="5" value="6th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CB9C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x62A" flags="0x0">
    <title>P1574 Check - Vehicle Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): the check stops and waits for the arm speed again once vehicle speed falls to this. Stock 5 km/h. Effect: raise = the check stops at a higher speed Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37544" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x62B" flags="0x0">
    <title>P1574 Check - Arm Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): the check arms once vehicle speed reaches this. Stock 32 km/h. Effect: raise = the check arms at a higher speed Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37548" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x62C" flags="0x0">
    <title>STFT Tip-In Reset Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: the tip-in reset is only allowed below this vehicle speed. Stock 10 km/h. Effect: raise = the tip-in reset also happens at higher speed Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25954" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x62D" flags="0x0">
    <title>Hot-Restart Fuel - Latch Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot-restart fuel gate: a latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, the Open Loop Hot-Restart Gain table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. This is the latch coolant threshold. Stock 105 C. Effect: raise = the engine must run hotter before a hot restart is armed Evi...</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28EC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x62E" flags="0x0">
    <title>Learned MAF/VE Ratio - Deep Vacuum MAP</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM learns a MAF to VE airflow ratio in steady state and uses it on the VE airflow during transients. While manifold pressure is below the deep vacuum MAP (closed throttle decel) learning is frozen; on the first update back above it, a learned ratio below the reset threshold is put back to 1.0, and a higher one is kept. This is the deep vacuum MAP. Stock 20 kPa. Effect: raise = learning freezes over more of the decel range and the reset check runs more often Evidence: ledger:E0219, ledger:E0671, ledger:E0856</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2B1EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x62F" flags="0x0">
    <title>Cam Signal Lost Test - Run Condition, Airflow Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam position sensor signal lost test (P0340 / P0365): least airflow for the test to run. Stock 0 g/s (no limit). Effect: raise = the test only runs above this airflow Evidence: ledger:E1080</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34CA2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x630" flags="0x0">
    <title>Misfire - Dead Cylinder Exemption Load Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: highest load at which a single dead cylinder is exempt from the catalyst-damage limit. Stock 30 %. Effect: raise = the exemption reaches higher load Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37204" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x631" flags="0x30">
    <title>EVAP Engine-Off Test - Disturbance Threshold vs Fuel Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: change of the filtered tank reading within one disturbance check interval, by fuel level, above which a disturbance is flagged (tank pressure sensor noise or a sudden pressure change). Stock 0.45 inH2O at every fuel level. Effect: raise = a larger pressure change is tolerated before a disturbance is flagged Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x346D0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>inH2O</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x632" flags="0x30">
    <title>Low Oil Pressure Check - Minimum Oil Pressure vs RPM (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With the oil pressure sensor path on: minimum oil pressure for the engine speed. When the engine is running and oil pressure stays below this value, the PCM sets its low oil pressure state; it clears once oil pressure reaches this value plus the recovery margin. Stock 0 kPa at 0 rpm, 35 kPa around idle, rising to 216 kPa at high engine speed. The oil pressure sensor path is switched off in the stock calibration (Oil Pressure Sensor Path Enable = 0; the PCM uses its oil pressure estimate instead), so this has no effect on the stock calibration (dormant). Effect: lower values make the low oil pressure warning less sensitive Evi...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23164" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x633" flags="0x30">
    <title>Engine Oil Pressure vs Sensor Voltage (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil pressure the PCM reads from the oil pressure sensor voltage (the value the scan tool shows as engine oil pressure) when the sensor path is on. Stock 0 kPa up to 0.3 V, then rising about 77 kPa per 0.3 V to 882 kPa at 4.7 V and above. The oil pressure sensor path is switched off in the stock calibration (Oil Pressure Sensor Path Enable = 0; the PCM uses its oil pressure estimate instead), so this has no effect on the stock calibration (dormant). Effect: raise = a higher oil pressure is read for the same sensor voltage Evidence: ledger:E0674, ledger:E1410, ledger:E1831</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>V</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.000" />
      <LABEL index="1" value="0.312" />
      <LABEL index="2" value="0.625" />
      <LABEL index="3" value="0.938" />
      <LABEL index="4" value="1.250" />
      <LABEL index="5" value="1.562" />
      <LABEL index="6" value="1.875" />
      <LABEL index="7" value="2.188" />
      <LABEL index="8" value="2.500" />
      <LABEL index="9" value="2.812" />
      <LABEL index="10" value="3.125" />
      <LABEL index="11" value="3.438" />
      <LABEL index="12" value="3.750" />
      <LABEL index="13" value="4.062" />
      <LABEL index="14" value="4.375" />
      <LABEL index="15" value="4.688" />
      <LABEL index="16" value="5.000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23192" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x634" flags="0x30">
    <title>Engine Oil Pressure Estimate vs Coolant and RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil pressure the PCM estimates from coolant temperature (-40 to 152 C) and engine speed (400 to 3600 rpm) when it runs without an oil pressure sensor (stock). The estimate is smoothed and sent on the vehicle bus (Class 2 message 4B11, 4 kPa per count), the value the oil pressure gauge shows. Stock about 415 to 496 kPa at -40 C and 240 to 470 kPa once warm, rising with engine speed. Effect: changes the oil pressure the PCM reports Evidence: ledger:E0274, ledger:E0675, ledger:E1246, ledger:E1408, ledger:E1831</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x231C4" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x635" flags="0x30">
    <title>P0116 Test - Startup Coolant Above Intake Air Fail Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116): the code sets outright when coolant at start-up is at least this much warmer than intake air, by intake air temperature. Stock 100 C everywhere. Effect: lower = a smaller coolant to intake air gap fails the test Evidence: ledger:E1011, ledger:E1288</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (intake air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x336FC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x636" flags="0x30">
    <title>Misfire - Minimum Load</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: load below which misfire detection is paused, by engine speed (400 to 6500 rpm; at 7000 rpm and above there is no minimum). The value is multiplied by the coolant factor curve. Stock 20 % at 400 rpm, 14 % from 800 to 1600 rpm, rising to 43 % at 6500 rpm. Effect: raise = misfire detection is paused up to a higher load Evidence: ledger:E0676, ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x368F4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>26</indexcount>
      <units>rpm</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3701C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x637" flags="0x30">
    <title>O2 Response Test (P1133) - Min Rich Switches</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1133 sets if the sensor rises to 600 mV or above fewer times than this during the test. Stock 100. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: raise = the sensor must switch more often to pass Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x348DA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>count</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x638" flags="0x30">
    <title>O2 Response Test (P1133) - Min Lean Switches</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1133 sets if the sensor falls to 500 mV or below fewer times than this during the test. Stock 100. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: raise = the sensor must switch more often to pass Evidence: ledger:E0281, ledger:E0295, ledger:E0902, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <LABEL index="17" value="85" />
      <LABEL index="18" value="90" />
      <LABEL index="19" value="95" />
      <LABEL index="20" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34906" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>count</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x639" flags="0x0">
    <title>Secondary Air - Requested Test Coolant Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The secondary air test started on request runs only while coolant is below this (with the intake air, baro and other limits of the normal secondary air start). Stock 80 C. Secondary air injection is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0676, ledger:E0836, ledger:E1193, ledger:E1194</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x21654" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x63A" flags="0x0">
    <title>Secondary Air - Requested Test Fuel Correction Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the secondary air fuel correction stays active in the secondary air test started on request. Stock 20 s. Secondary air injection is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0676, ledger:E0836, ledger:E1193, ledger:E1194</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3269A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x63B" flags="0x0">
    <title>Secondary Air - Requested Test Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long secondary air runs when the secondary air test is started on request (for example from a scan tool). Stock 30 s. Secondary air injection is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0676, ledger:E0836, ledger:E1193, ledger:E1194</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3269C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x63C" flags="0x30">
    <title>Catalyst Monitor - RPM Span Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): largest engine speed movement allowed during a test: first value before the fuel steps, second value during them. More movement ends the test. Stock 500 rpm. Effect: raise = more engine speed movement is tolerated during a test Evidence: ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>phase</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="before the fuel steps" />
      <LABEL index="1" value="during the fuel steps" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x328FE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x63D" flags="0x30">
    <title>Catalyst Monitor - Load Span Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): largest engine load movement allowed during a test: first value before the fuel steps, second value during them. Stock 50 %. Effect: raise = more load movement is tolerated during a test Evidence: ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>phase</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="before the fuel steps" />
      <LABEL index="1" value="during the fuel steps" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x32912" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x63E" flags="0x0">
    <title>P0125 / P0128 Check - Airflow Counted Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: airflow above this is counted as this much when the checks add up the air the engine has drawn since start. Stock 55 g/s. Effect: raise = high airflow counts in full toward the required air mass Evidence: ledger:E0776, ledger:E0805, ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33726" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x63F" flags="0x30">
    <title>P0125 / P0128 Check - Start-Up Coolant Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: each check only runs on starts where coolant temperature at start-up was at or below its value here. Stock 36.25 degC for P0125 and 75 degC for P0128. Effect: raise = the check also runs after warmer starts Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>check</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="P0125" />
      <LABEL index="1" value="P0128" />
      <LABEL index="2" value="third column (unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33792" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x640" flags="0x30">
    <title>P0125 / P0128 - Coolant Target Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: coolant must have reached this by the time the engine has drawn the required air mass; reaching it reports a pass. Stock 36.25 degC for P0125 and 80 degC for P0128 (the thermostat check). Effect: lower = a cooler running engine still passes Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>check</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="P0125" />
      <LABEL index="1" value="P0128" />
      <LABEL index="2" value="third column (unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33798" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x641" flags="0x30">
    <title>P0125 / P0128 Check - Distance Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: each check only fails once the vehicle has also been driven this far since start. Stock 0.57 km for P0125 and 1.71 km for P0128. Effect: raise = more distance is needed before the code can set Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>check</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="P0125" />
      <LABEL index="1" value="P0128" />
      <LABEL index="2" value="third column (unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3379E" mmedelementsizebits="32" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1193046.470833</max>
      <MATH equation="X/3600"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x642" flags="0x0">
    <title>P1574 Check - Deceleration Speed Drop</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): a deceleration is counted when vehicle speed falls by at least this much inside the deceleration window. Stock 4 km/h. Effect: raise = only harder decelerations are counted Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37540" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x643" flags="0x0">
    <title>P1574 Check - Deceleration Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): the speed drop is measured from a reference speed that is refreshed after this long. Stock 0.5 s. Effect: raise = slower decelerations are also counted Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37542" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x644" flags="0x0">
    <title>P1574 Check - Speed Signal Difference Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): the check restarts if its two vehicle speed signals differ by this much or more. Stock 10 km/h. Effect: raise = a larger speed signal difference is tolerated Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37546" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x645" flags="0x0">
    <title>Crank Variation Learn - Arm RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn (the service procedure that clears P0315): sampling is armed once engine speed has risen above this. Stock 3970 rpm. Effect: raise = the engine must be revved higher before sampling is armed Evidence: ledger:E1040</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x646" flags="0x0">
    <title>Crank Variation Learn - Factor Average Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn: a learn is stored, and the stored factors are accepted (otherwise P0315 sets), only when the average of the five cylinder factors is below this. Stock 1.0008. Effect: raise = a learn with a higher average factor is accepted Evidence: ledger:E1081</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328C8" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>26214.399994</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163840"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x647" flags="0x0">
    <title>Crank Variation Learn - Factor Average Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn: a learn is stored, and the stored factors are accepted (otherwise P0315 sets), only when the average of the five cylinder factors is above this. Stock 0.9992. Effect: lower = a learn with a lower average factor is accepted Evidence: ledger:E1081</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328CC" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>26214.399994</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163840"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x648" flags="0x30">
    <title>Catalyst Monitor - First Step Downstream Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: if the downstream O2 sensor took longer than this to switch in the first fuel step, the catalyst is given the maximum storage time. Stock 5.9 s. Effect: lower = a slow downstream switch is scored as maximum storage sooner Evidence: ledger:E1000</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x329C0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x649" flags="0x30">
    <title>Catalyst Monitor - Storage Time Reference</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: each test&#x27;s oxygen storage time, after correction for airflow and catalyst temperature, is compared with this reference; the amount it falls short is the test result. Stock 3.0 s. Effect: lower = a catalyst with less oxygen storage still scores as good Evidence: ledger:E1021</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>bank</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x329C4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x64A" flags="0x0">
    <title>Catalyst Monitor - Rich Step Downstream Switch Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: when the test starts with its rich step (stock), the downstream O2 sensor counts as switched once it reads at or above this. Stock 600 mV. Effect: lower = the downstream sensor counts as switched at a lower reading Evidence: ledger:E1000</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x329E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x64B" flags="0x0">
    <title>Catalyst Monitor - Lean First Step Upstream Switch Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only used if the test is set to start with a lean step (not stock): the upstream O2 sensor counts as switched once it reads at or below this. Stock 300 mV. Effect: raise = the upstream sensor counts as switched at a higher reading Evidence: ledger:E1000</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x329EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x64C" flags="0x0">
    <title>Catalyst Monitor - Lean First Step Downstream Switch Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only used if the test is set to start with a lean step (not stock): the downstream O2 sensor counts as switched once it reads at or below this. Stock 300 mV. Effect: raise = the downstream sensor counts as switched at a higher reading Evidence: ledger:E1000</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x329EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x64D" flags="0x0">
    <title>Catalyst Monitor - Second Step Switch Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: in the second fuel step (lean, with the stock rich first step) each O2 sensor counts as switched once it reads at or below this. Stock 300 mV. Effect: raise = the sensors count as switched at a higher reading Evidence: ledger:E1000</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x329EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x64E" flags="0x30">
    <title>Exhaust Temperature Model - Warm Flag Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): a channel counts as warm at or above this modelled temperature. Channel 3 is the catalyst channel: while it is warm the catalyst monitor (P0420) readiness counter counts up once per second (down while it is not), and the test can arm only once the counter reaches its threshold. The warm flags of channels 1 and 2 are not used on this calibration. Stock 450 C. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = the catalyst test needs a hotter modelled catalyst bef...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x337F0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1023.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x64F" flags="0x30">
    <title>Cam Angle Test - Angle Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam angle test (sets P0017 on this engine; runs with the cam phaser parked): lowest measured cam angle that counts as in range for a cylinder. Stock 48.8 deg. The second value belongs to the other cam input, which this test does not check. The array has room for four cam inputs; this engine has two, so the third and fourth values are never used. Effect: lower = a more retarded or advanced cam reading still passes Evidence: ledger:E1080, ledger:E1526</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input reporting P0365 / P0366 / P0017" />
      <LABEL index="1" value="cam input reporting P0340 / P0341 / P0016" />
      <LABEL index="2" value="cam input 3 (not fitted, unused)" />
      <LABEL index="3" value="cam input 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34CC8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-128.000000</min>
      <max>127.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x650" flags="0x30">
    <title>Cam Angle Test - Angle Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam angle test (sets P0017 on this engine; runs with the cam phaser parked): highest measured cam angle that counts as in range for a cylinder. Stock 56.6 deg. The second value belongs to the other cam input, which this test does not check. The array has room for four cam inputs; this engine has two, so the third and fourth values are never used. Effect: raise = a larger cam angle reading still passes Evidence: ledger:E1080, ledger:E1526</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input reporting P0365 / P0366 / P0017" />
      <LABEL index="1" value="cam input reporting P0340 / P0341 / P0016" />
      <LABEL index="2" value="cam input 3 (not fitted, unused)" />
      <LABEL index="3" value="cam input 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34CD0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-128.000000</min>
      <max>127.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x651" flags="0x30">
    <title>Cam Angle Test - Cylinders Out of Range</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam angle test (sets P0017 on this engine; runs with the cam phaser parked): number of the five per-cylinder angles that must be out of range for a sample to count as bad. Stock 2. The array has room for four cam inputs; this engine has two, so the third and fourth values are never used. Effect: raise = more cylinders must read out of range before a sample is bad Evidence: ledger:E1080, ledger:E1526</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input reporting P0365 / P0366 / P0017" />
      <LABEL index="1" value="cam input reporting P0340 / P0341 / P0016" />
      <LABEL index="2" value="cam input 3 (not fitted, unused)" />
      <LABEL index="3" value="cam input 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34CD8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>cylinders</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x652" flags="0x30">
    <title>P0335 Count Test - Fail Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0335 crank count test (runs only while the engine turns on the cam signal with the crank signal not synchronised): bad samples that set P0335. Stock 8. Effect: raise = more bad samples are needed to set the code Evidence: ledger:E1080</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="crank sensor" />
      <LABEL index="1" value="not used" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34CF0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x653" flags="0x30">
    <title>P0335 Count Test - Counts Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0335 crank count test (runs only while the engine turns on the cam signal with the crank signal not synchronised): fewest crank counts per sample that count as good. Stock 90 (nominal 100). Effect: lower = fewer crank counts are accepted Evidence: ledger:E1080</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="crank sensor" />
      <LABEL index="1" value="not used" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34CF4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>counts</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x654" flags="0x30">
    <title>P0335 Count Test - Counts Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0335 crank count test (runs only while the engine turns on the cam signal with the crank signal not synchronised): most crank counts per sample that count as good. Stock 110 (nominal 100). Effect: raise = more crank counts are accepted Evidence: ledger:E1080</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="crank sensor" />
      <LABEL index="1" value="not used" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34CF8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>counts</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x655" flags="0x30">
    <title>P0335 Count Test - Samples per Block</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0335 crank count test (runs only while the engine turns on the cam signal with the crank signal not synchronised): samples after which the bad sample count starts over if the fail count was not reached. Stock 10. Effect: raise = bad samples are collected over a longer block Evidence: ledger:E1080</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="crank sensor" />
      <LABEL index="1" value="not used" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34CFC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x656" flags="0x0">
    <title>P0335 Count Test - Events per Sample</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0335 crank count test (runs only while the engine turns on the cam signal with the crank signal not synchronised): number of engine cycle events over which crank counts are added up for one sample. Stock 10. Effect: change together with the count limits: they are counts per sample Evidence: ledger:E1080</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34D00" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>events</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x657" flags="0x30">
    <title>Cam Signal Lost Test - Pass Counts</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam position sensor signal lost test (P0365 / P0340): cam signal counts that must be seen within the fail time to pass. Stock 5 and 1. The array has room for four cam inputs; this engine has two, so the third and fourth values are never used. Effect: raise = more cam signal activity is needed to pass Evidence: ledger:E1080, ledger:E1526</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input reporting P0365 / P0366 / P0017" />
      <LABEL index="1" value="cam input reporting P0340 / P0341 / P0016" />
      <LABEL index="2" value="cam input 3 (not fitted, unused)" />
      <LABEL index="3" value="cam input 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D78" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>counts</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x658" flags="0x0">
    <title>Airflow Rationality - Airflow Difference Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101): filtered difference, in either direction, between measured airflow (MAF) and the airflow modelled from throttle position above which the airflow check is failing. Together with a failing second pressure check this sets P0101. Stock 15 g/s. Effect: raise = a larger airflow disagreement is tolerated Evidence: ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36740" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>-512.000000</min>
    <max>511.984375</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/64"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x659" flags="0x0">
    <title>Airflow Rationality - Pressure Difference Limit, Throttle Model</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow rationality test (P0101 / P0106 / P0121 / P1101): filtered difference, in either direction, between measured manifold pressure and the pressure modelled from throttle position above which the first pressure check is failing. Together with a failing second pressure check this sets P0106. Stock 20 kPa. Effect: raise = a larger pressure disagreement is tolerated Evidence: ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36742" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x65A" flags="0x0">
    <title>Misfire - Emission Failed Windows Required</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: number of failed emission windows among the recent ones that makes one emission exceedance. An exceedance in the first 3200 revolutions after start, or the fourth one later in the trip, sets P0300. Stock 5. Keep below 256. Effect: raise = more failed windows are needed before the code sets Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3712E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>windows</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x65B" flags="0x0">
    <title>Misfire - Abnormal Event Ratio Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: each detected event is classed as a normal misfire shape or an abnormal (disturbance) shape. When the abnormal events in a 200-revolution window exceed this percentage of the normal ones, the window is marked as a disturbance and gets no decision unless the disturbance override count is reached. Stock 50 %. Effect: raise = more abnormal events are tolerated before a window is set aside Evidence: ledger:E0780, ledger:E0805, ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x65C" flags="0x0">
    <title>Misfire - Disturbance Override Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: a window marked as a disturbance (too many abnormal events, see the abnormal event ratio limit) normally gets no decision. When the window holds at least this many misfires it is judged anyway. Stock 90 misfires in 500 firings. Effect: lower = disturbed windows are judged at a lower misfire count Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371FE" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>misfires</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>127.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x65D" flags="0x0">
    <title>Misfire - Emission Limit Multiplier After Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: multiplier applied to the emission limit during the first 16 windows (3200 revolutions) after start. Stock 1.0. Effect: raise = more misfire is tolerated in the first 3200 revolutions Evidence: ledger:E0780, ledger:E0805, ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37200" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction (Q12, 4096=1.0)</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x65E" flags="0x0">
    <title>Misfire - Dead Cylinder Exemption Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: a window over the catalyst-damage limit is not counted as catalyst damaging when engine speed is at or below this, load is at or below the exemption load and one cylinder alone has the dead cylinder misfire count. The emission limit still applies. Stock 2000 rpm. Effect: raise = the exemption reaches higher engine speed Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37202" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x65F" flags="0x0">
    <title>Misfire - Emission Limit Multiplier, Special Period</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: multiplier applied to the emission limit for a calibrated period after an internal stored flag clears. That period is zero in the stock calibration, so this value is not used. Stock 1.0. Effect: no effect in the stock calibration Evidence: ledger:E0780, ledger:E0805, ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37224" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction (Q12, 4096=1.0)</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x660" flags="0x30">
    <title>Charge Temperature - Coolant Weight vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Charge temperature model (used by the VE airflow model and the VE Maximum airmass cap): the charge temperature moves toward intake air temperature plus a fraction of the coolant-to-intake difference, the fraction set by airflow (more airflow, closer to intake temperature), through a lag filter whose speed is also set by airflow. This is the fraction of the coolant-to-intake difference added to intake temperature. Stock 0.16 at idle airflow down to 0.003 at 128 g/s. Effect: raise = charge temperature reads hotter (less VE airmass) Evidence: ledger:E0677, ledger:E0878</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s (airflow)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <LABEL index="17" value="68" />
      <LABEL index="18" value="72" />
      <LABEL index="19" value="76" />
      <LABEL index="20" value="80" />
      <LABEL index="21" value="84" />
      <LABEL index="22" value="88" />
      <LABEL index="23" value="92" />
      <LABEL index="24" value="96" />
      <LABEL index="25" value="100" />
      <LABEL index="26" value="104" />
      <LABEL index="27" value="108" />
      <LABEL index="28" value="112" />
      <LABEL index="29" value="116" />
      <LABEL index="30" value="120" />
      <LABEL index="31" value="124" />
      <LABEL index="32" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x230C6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x661" flags="0x30">
    <title>Purge Flow - Hot Restart Request vs Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge: purge flow requested during a hot restart, before normal purge is enabled, by time since the start (0 to 128 s). Stock 16 to 38. Purge flow units: the full scale word (stock 123) is full purge reference flow. Effect: raise = more purge right after a hot restart Evidence: ledger:E1122</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>s run time</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <LABEL index="17" value="68" />
      <LABEL index="18" value="72" />
      <LABEL index="19" value="76" />
      <LABEL index="20" value="80" />
      <LABEL index="21" value="84" />
      <LABEL index="22" value="88" />
      <LABEL index="23" value="92" />
      <LABEL index="24" value="96" />
      <LABEL index="25" value="100" />
      <LABEL index="26" value="104" />
      <LABEL index="27" value="108" />
      <LABEL index="28" value="112" />
      <LABEL index="29" value="116" />
      <LABEL index="30" value="120" />
      <LABEL index="31" value="124" />
      <LABEL index="32" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2526C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flow units</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x662" flags="0x30">
    <title>Calculated Load - Reference Airflow vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow that counts as 100 % calculated load at each rpm (corrected by baro and the IAT factor). Only changes the calculated load value reported to a scan tool (PID 04), not fuelling. Stock 0 rising to 180 g/s at 6000 rpm. Effect: raise = lower reported calculated load at that rpm Evidence: ledger:E0740, ledger:E1340</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C28C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x663" flags="0x30">
    <title>Cam Phasing Enable - RPM Off Below vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phasing is allowed only while all of its enable conditions hold. The rpm condition turns off below this engine speed, by coolant temperature. Stock 950 to 1500 rpm. Effect: raise = cam phasing drops out at a higher rpm at that coolant Evidence: ledger:E0738</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22D4A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x664" flags="0x30">
    <title>Purge Enable - Closed Loop Time Before First Purge vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: time in closed loop fuel control before the first purge of a trip, by coolant temperature at start (-40 to 152 C). Stock 290 s after a -40 C start down to 20 s from 80 C. Effect: raise = purge starts later after the engine goes closed loop Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC startup coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x252FE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x665" flags="0x30">
    <title>Purge Enable - Coolant Offset Above Closed Loop Enable vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: purge may switch on only when coolant is above the closed loop enable coolant temperature plus this offset, by coolant temperature at start (-40 to 152 C). Stock 5 C after a very cold start rising to 17 C from a 20 C start (72 C at a 20 C start). Effect: raise = purge waits for a warmer engine Evidence: ledger:E0781, ledger:E0792, ledger:E0805, ledger:E0936, ledger:E1116</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC startup coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2532A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x666" flags="0x30">
    <title>O2 Sensor Ready - Run Time vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor ready logic: engine run time that must pass before an O2 sensor can be flagged ready, by coolant temperature at start-up. Stock 40 s cold to 3 s warm. Effect: raise = sensors are flagged ready later after a start Evidence: ledger:E1005, ledger:E1288</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28F06" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x667" flags="0x30">
    <title>Generator Control - Low Engine Speed Limit vs Desired Idle, Park / Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Park / Neutral. While the engine runs at or below this speed, looked up from the desired idle speed, the generator (alternator) control leaves its normal output command and uses its low speed command, until engine speed rises above it or the low speed time limit runs out. Stock 450 rpm at 500 rpm desired idle, 525 rpm from 600 rpm desired idle up. Effect: raise = the generator control switches to its low speed command at a higher engine speed Evidence: ledger:E0677, ledger:E1367</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="500" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="700" />
      <LABEL index="3" value="800" />
      <LABEL index="4" value="900" />
      <LABEL index="5" value="1000" />
      <LABEL index="6" value="1100" />
      <LABEL index="7" value="1200" />
      <LABEL index="8" value="1300" />
      <LABEL index="9" value="1400" />
      <LABEL index="10" value="1500" />
      <LABEL index="11" value="1600" />
      <LABEL index="12" value="1700" />
      <LABEL index="13" value="1800" />
      <LABEL index="14" value="1900" />
      <LABEL index="15" value="2000" />
      <LABEL index="16" value="2100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28F56" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x668" flags="0x30">
    <title>Desired Idle Minimum vs Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Desired idle: lowest desired idle speed by vehicle speed (0 to 40 km/h). It is one of the requests of which the largest wins. Stock 595 rpm up to 15 km/h and 875 rpm from 20 km/h, so the idle target is raised while the truck is rolling. Effect: raise = higher idle target at that road speed Evidence: ledger:E1112</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A582" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x669" flags="0x30">
    <title>EVAP Purge - Ramp Rate Falling, Low Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the gap to the purge target closed on each purge update (about a tenth of a second) when commanded purge is falling below the speed split, by airflow. Stock 100 % (instant). Effect: raise = purge follows its target faster Evidence: ledger:E0739, ledger:E1124</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x250C2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x66A" flags="0x30">
    <title>EVAP Purge - Ramp Rate Rising, Low Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the gap to the purge target closed on each purge update (about a tenth of a second) when commanded purge is rising below the speed split, by airflow. Stock 10 %, a gradual ramp-in. Effect: raise = purge follows its target faster Evidence: ledger:E0739, ledger:E1124</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x250D6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x66B" flags="0x30">
    <title>Torque Reduction - Fewest Fuelled Cylinders vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque reduction (traction control): fewest cylinders that stay fuelled, by coolant temperature. Stock 5 at every point, the full cylinder count, so no cylinder is ever cut for a torque reduction and the reduction is done with spark and throttle. Lower values allow fuel cut on some cylinders, which sends unburnt air to the catalyst. Effect: lower = cylinders may be cut during a torque reduction Evidence: ledger:E1130</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x313B6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>cylinders</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x66C" flags="0x0">
    <title>Cam Phasing Region - RPM Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How far engine speed must pass an rpm band edge before the cam phasing region changes. Stock 50 rpm. Effect: raise = less region hunting near an rpm edge Evidence: ledger:E0744</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2306E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x66D" flags="0x0">
    <title>Cam Phasing Region - Throttle Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How far throttle must pass a throttle band edge before the cam phasing region changes. Stock 0.15 %. Effect: raise = less region hunting near a throttle edge Evidence: ledger:E0744</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x23070" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x66E" flags="0x0">
    <title>Diagnostic RPM Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. An engine speed ceiling used by a diagnostic monitor: below this speed the monitor&#x27;s alternate fault path can trigger, at or above it that path is skipped. Stock is 4200 rpm. Effect: Raising it raises the engine speed ceiling below which this monitor&#x27;s alternate fault path can trigger; lowering it lowers that ceiling. Evidence: ledger:E0776, ledger:E0805</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x239EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x66F" flags="0x0">
    <title>Crank Wheel - Teeth per Revolution (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of teeth per crankshaft revolution on the crank wheel, used to turn the measured tooth period into engine speed. Stock 60. Reference only: DO NOT EDIT. Effect: reference only (crank wheel geometry) Evidence: ledger:E0438, ledger:E0775, ledger:E1272, ledger:E1274</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x23A3E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>teeth per revolution</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x670" flags="0x0">
    <title>Crank and Cam Signal Loss Watchdog B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A companion watchdog timer that, once it reaches this value without seeing a qualifying crank or cam signal event, forces engine speed, mass airflow and related running values back to zero. Stock is 0.8 seconds. Effect: Raising it allows a longer gap since the last qualifying crank or cam signal event before this watchdog resets those readings; lowering it makes the watchdog trip sooner. Evidence: ledger:E0775, ledger:E0805</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x23A43" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x671" flags="0x0">
    <title>Throttle Position Check Settle Timer</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A settle time that must elapse before the throttle-position pass/fail check below it is evaluated. Stock is 0.5 seconds. Effect: Raising it extends the settle time before the throttle-position check is evaluated; lowering it shortens it. Evidence: ledger:E0775, ledger:E0805</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23C32" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x672" flags="0x0">
    <title>Throttle Position Pass/Fail Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the settle timer above has elapsed, the throttle position reading is compared against this percentage to decide pass or fail for this check. Stock is about 36.0 percent throttle. Effect: Raising it raises the throttle-position percentage the reading is compared against for this check; lowering it lowers that boundary. Evidence: ledger:E0775, ledger:E0805</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23C34" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x673" flags="0x0">
    <title>Throttle Monitor Over-Limit Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Electronic throttle safety monitor: how long the throttle request worked out from the pedal may stay above the monitor&#x27;s allowed ceiling before the monitor acts (it then holds the request at the ceiling and sets its fault state). Stock 0.19 seconds. This is a throttle safety check: do not raise it casually. Effect: raise = the throttle request may exceed the monitor ceiling for longer before the monitor acts Evidence: ledger:E0775, ledger:E0805, ledger:E1124</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x24F46" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x674" flags="0x0">
    <title>Purge O2 Feedback - Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: normal step of the purge factor, up when lean and down when rich. Stock 0.0075. Effect: raise = the purge amount follows the O2 sensor faster Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25130" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x675" flags="0x0">
    <title>Purge O2 Feedback - Factor Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: lowest value of the purge factor. Stock 0: purge can be taken away completely. Effect: raise = some purge always remains when the mixture is rich Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25134" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x676" flags="0x0">
    <title>Purge O2 Feedback - Factor at Key-On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: value of the purge factor at key-on. Stock 0.35: each trip starts with about a third of the full purge request. Effect: raise = each trip starts with more purge Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25136" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x677" flags="0x0">
    <title>Purge Enable - Fuelled Cylinders Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: purge runs only with at least this many cylinders being fuelled. Stock 5: purge stops whenever a cylinder is cut (decel fuel cut, limiters). Effect: lower = purge keeps running with cylinders cut Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2534E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cylinders</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x678" flags="0x0">
    <title>LTFT Learn Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: time between learn steps of a cell. Stock 1 s. Effect: lower = long term trim learns faster Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25684" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x679" flags="0x30">
    <title>Rear O2 Trim - Learned Offset Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: highest learned switch point offset, by airflow region. Stock 100 mV (125 mV in the mid and high airflow regions). Effect: raise = the rear sensor may raise the switch point further Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>airflow region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="low airflow" />
      <LABEL index="1" value="closed throttle idle" />
      <LABEL index="2" value="mid airflow" />
      <LABEL index="3" value="high airflow" />
      <LABEL index="4" value="not used on stock" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x257A6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x67A" flags="0x30">
    <title>Rear O2 Trim - Learned Offset Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: lowest learned switch point offset, by airflow region. Stock -50 mV, -25 mV at idle, -60 mV in the mid and high airflow regions. Effect: lower = the rear sensor may lower the switch point further Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>airflow region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="low airflow" />
      <LABEL index="1" value="closed throttle idle" />
      <LABEL index="2" value="mid airflow" />
      <LABEL index="3" value="high airflow" />
      <LABEL index="4" value="not used on stock" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x257B0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x67B" flags="0x30">
    <title>Rear O2 Trim - Learn Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: time the rear sensor must stay rich or lean for each learn step, by airflow region. Stock 1.0 s, 1.5 s at idle, 0.5 s in the mid and high airflow regions. Effect: lower = the offset is learned faster Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>airflow region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="low airflow" />
      <LABEL index="1" value="closed throttle idle" />
      <LABEL index="2" value="mid airflow" />
      <LABEL index="3" value="high airflow" />
      <LABEL index="4" value="not used on stock" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x257BA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x67C" flags="0x0">
    <title>Rear O2 Trim - Not Active Band, Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: lower edge of the rear sensor not-active band; a reading at or below it counts toward the active time. Stock 350 mV. Effect: lower = a leaner reading is needed to count as activity Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x258FA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x67D" flags="0x30">
    <title>Rear O2 Trim - Rear O2 Lean Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: filtered rear O2 voltage at or below which the rear sensor counts as lean (the learned offset then moves up), by airflow region. Stock 625 mV, 650 mV at idle, 600 mV in the mid and high airflow regions. Row 2 is for a second bank, which this single-bank engine does not have: it has no effect on the stock calibration (dormant). Effect: raise = the rear sensor counts as lean at a higher voltage Evidence: ledger:E1089, ledger:E1386</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>airflow region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="low airflow" />
      <LABEL index="1" value="closed throttle idle" />
      <LABEL index="2" value="mid airflow" />
      <LABEL index="3" value="high airflow" />
      <LABEL index="4" value="not used on stock" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>bank</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x258FC" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x67E" flags="0x30">
    <title>Rear O2 Trim - Rear O2 Rich Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: filtered rear O2 voltage at or above which the rear sensor counts as rich (the learned offset then moves down), by airflow region. Stock 660 mV, 700 mV at idle, 625 mV in the mid and high airflow regions. Row 2 is for a second bank, which this single-bank engine does not have: it has no effect on the stock calibration (dormant). Effect: lower = the rear sensor counts as rich at a lower voltage Evidence: ledger:E1089, ledger:E1386</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>airflow region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="low airflow" />
      <LABEL index="1" value="closed throttle idle" />
      <LABEL index="2" value="mid airflow" />
      <LABEL index="3" value="high airflow" />
      <LABEL index="4" value="not used on stock" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>bank</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25910" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x67F" flags="0x0">
    <title>Acceleration Fuel Adder - Short Term Trim Hold Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel: fuel-removing steps of the short term trim are held while the acceleration fuel adder is at or above this much fuel per injection. Stock 2000 mg. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: lower = the trim stops removing fuel at a smaller acceleration adder Evidence: ledger:E1139</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2599C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>mg</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>2047.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x680" flags="0x0">
    <title>Closed Loop Slow-Sensor Tables - Minimum O2 Switch Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel: when the O2 response test counted fewer rich to lean or lean to rich switches than this, the slow sensor tables are used on both sides and the size of the O2 excursion is ignored (the trim then steps at the zero error interval and the purge feedback gets no O2 signal) until a later response test passes. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = a sensor that switches rarely in the response test is treated as slow Evidence: ledger:E1140</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25CDE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>switches</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x681" flags="0x0">
    <title>Transient Fuel - Tip-Out Film Shrink Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transient fuel, tip-out mode: the mode is kept only while the wall film of the cylinder shrinks by at least this much per injection. Stock 0 mg: the mode ends as soon as the film starts to grow. Effect: raise = the tip-out mode ends earlier, while the film is still shrinking slowly Evidence: ledger:E1139</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26752" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mg</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x682" flags="0x0">
    <title>Hot-Restart Fuel - Latch Corrected Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot-restart fuel gate: a latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, the Open Loop Hot-Restart Gain table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. This is the corrected coolant threshold that arms the latch on its own. Stock 120 C. Effect: raise = the corrected-coolant pat...</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28EC6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x683" flags="0x0">
    <title>Hot-Restart Fuel - Maximum Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot-restart fuel gate: a latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, the Open Loop Hot-Restart Gain table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. This is the maximum run time after the start. Stock 45 s. Effect: raise = hot-restart fuel stays on longer after the start Evi...</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28EC8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x684" flags="0x0">
    <title>O2 Sensor Ready - Active Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor ready logic: a sensor is flagged ready once more than this many samples have read outside the resting band. Stock 10. Effect: raise = more activity is needed before a sensor is flagged ready Evidence: ledger:E1005</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28F50" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x685" flags="0x30">
    <title>Idle A/C - Adder Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: how long the idle air adder is held before it decays: first value at A/C clutch release, second at engagement. Stock 0.25 s each. Effect: raise = the extra idle air is held longer Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>event</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="A/C clutch release" />
      <LABEL index="1" value="A/C clutch engage" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2919E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x686" flags="0x0">
    <title>Idle A/C Handshake - Throttle Closed Area Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C clutch idle handshake: the throttle counts as closed only with the throttle area above the idle area at or below this (and the throttle at or below the throttle closed threshold). Stock 0.006 %. Effect: raise = a slightly open throttle still counts as closed for the A/C handshake Evidence: ledger:E1106</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x291A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x687" flags="0x30">
    <title>Idle Airflow Learn - Reset Values</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn: values the learned idle airflow starts from after the keep-alive memory is reset, for A/C off and A/C on. Stock 0 g/s for both. Effect: raise = the learn starts from more airflow after a memory reset Evidence: ledger:E1106</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>learn cell</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="A/C off" />
      <LABEL index="1" value="A/C on" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x291E2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x688" flags="0x0">
    <title>Desired Idle - During Traction Control Torque Reduction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Desired idle: idle speed requested while traction control is reducing engine torque, and afterwards for as long as the truck is slower than the request hold speed. It is one of the idle requests of which the largest wins. Stock 700 rpm. Effect: raise = higher idle target during and just after a traction control event Evidence: ledger:E1115</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A57E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x689" flags="0x0">
    <title>Airmass Estimate Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lag filter gain (fraction of the new sample blended in each update) applied to the engine&#x27;s mass airflow estimate. A value of 100 percent makes the filtered estimate follow each new reading immediately, with no smoothing; lower values blend in only part of each reading, smoothing out noise between updates. Stock value blends in about 15.5 percent of the new reading on every update. TunerPro shows the gain as a fraction of the new sample blended in per update: 1.0 follows each reading instantly (100 percent), lower values smooth more. Effect: raise = the airflow estimate follows a new mass airflow reading faster; lower =...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C27A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x68A" flags="0x0">
    <title>Volumetric Efficiency Maximum Limit Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below the dynamic airflow MAF-only engine speed (stock 5000 rpm), the cylinder airmass that spark and fuel use is capped at this maximum VE x barometric pressure / charge temperature x the limit multiplier (and x the learned MAF to VE ratio when that is above 1.0). Barometric pressure, not MAP, so under boost this cap holds the airmass near a naturally aspirated full charge whatever the MAF reads: stock about 0.70 g per cylinder at 2000 rpm and 0.84 g at 5000 rpm (100 kPa, 20 C). Above the MAF-only engine speed the cap is skipped. This multiplies that cap. Stock 1.03. Effect: raise = higher airmass ceiling below the MAF-only...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C482" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier (1.0 = no change)</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x68B" flags="0x30">
    <title>Spark Reference for Cam Target Reduction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Reference spark advance by rpm and airmass (0.08 to 1.36 g/cyl). When delivered spark stays below this reference for the Spark Reference Shortfall Confirm Time, the PCM starts reducing the load-based cam target: the Cam Target Spark-Limit Reduction factor (1.0 = no change) drops by its step down every down period, never below its floor, and climbs back once spark is at or above the reference. Stock flat -10 deg. The stock floor of 1.0 holds the factor at 1.0, so on the stock calibration this table changes nothing. Effect: raise = cam target reduction starts at higher delivered spark (only acts if the reduction floor is below...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl (airmass)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2FAD1" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X/2"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x68C" flags="0x30">
    <title>Open-Loop Fuel Gain vs Airflow and Temperature (in gear)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Open-loop fuel gain by airflow and modelled temperature, used in gear. Multiplies the open-loop commanded equivalence ratio together with a baro curve and a voltage curve (1.0 = no change). Stock 1.0 everywhere, so the stage is wired up but calibrated as no change on the H3. Effect: raise = the Q15 gain this table contributes to the open-loop commanded EQ chain goes up (currently pinned at 1.0/no correction across the whole airflow x temperature grid) Evidence: ledger:E0682, ledger:E0702, ledger:E0929</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>g/s (airflow)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>degC (modelled temperature)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x270D8" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x68D" flags="0x30">
    <title>Open-Loop Fuel Gain vs Airflow and Temperature (Park / Neutral)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Open-loop fuel gain by airflow and modelled temperature, used in Park / Neutral. Multiplies the open-loop commanded equivalence ratio together with a baro curve and a voltage curve (1.0 = no change). Stock 1.0 everywhere, so the stage is wired up but calibrated as no change on the H3. Effect: raise = the Q15 gain this table contributes to the open-loop commanded EQ chain goes up (currently pinned at 1.0/no correction across the whole airflow x temperature grid) Evidence: ledger:E0682, ledger:E0702, ledger:E0929</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>g/s (airflow)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>degC (modelled temperature)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x27540" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x68E" flags="0x30">
    <title>Idle Airflow Closed Loop - Mode 2 MAP Target (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle MAP target by rpm and vehicle speed for the idle airflow closed loop&#x27;s mode 2, scaled by a coolant factor (1.2 cold to 1.0 warm); the loop steps idle air on the MAP error from it. Mode 2 is not selected on the stock H3 (mode 1 is), so this table has no effect as delivered. Stock 30 kPa flat (E0726). Effect: no effect on the stock H3 (mode 2 not selected) Evidence: ledger:E0686, ledger:E0726, ledger:E0929</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="8" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="24" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="48" />
      <LABEL index="7" value="56" />
      <LABEL index="8" value="64" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="88" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="104" />
      <LABEL index="14" value="112" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x293CE" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x68F" flags="0x30">
    <title>Cam Phaser Proportional Gain - Cam At Or Past Command</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phaser controller proportional gain, by engine speed and coolant temperature: the solenoid duty changes by this many percent for each degree the cam is away from the commanded angle, times a learned factor that starts at 1.0 and only learns upward (12 learned slots by error direction, engine speed and coolant). This table is used while the cam is at or past the commanded angle (duty is taken away). Stock 3.9 to 6.5 % per degree. Effect: raise = the phaser is pulled back harder toward the commanded angle; too high can oscillate Evidence: ledger:E0690, ledger:E0837, ledger:E0850, ledger:E0929</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="800" />
      <LABEL index="1" value="1200" />
      <LABEL index="2" value="1600" />
      <LABEL index="3" value="2000" />
      <LABEL index="4" value="2400" />
      <LABEL index="5" value="2800" />
      <LABEL index="6" value="3200" />
      <LABEL index="7" value="3600" />
      <LABEL index="8" value="4000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC (corrected coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2291E" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%/deg</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x690" flags="0x30">
    <title>Cam Phaser Proportional Gain - Cam Behind Command</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phaser controller proportional gain, by engine speed and coolant temperature: the solenoid duty changes by this many percent for each degree the cam is away from the commanded angle, times a learned factor that starts at 1.0 and only learns upward (12 learned slots by error direction, engine speed and coolant). This table is used while the cam is behind the commanded angle (duty is added). Stock 2.0 to 5.7 % per degree. Effect: raise = the phaser is driven harder toward the commanded angle; too high can oscillate Evidence: ledger:E0690, ledger:E0837, ledger:E0850, ledger:E0929</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="800" />
      <LABEL index="1" value="1200" />
      <LABEL index="2" value="1600" />
      <LABEL index="3" value="2000" />
      <LABEL index="4" value="2400" />
      <LABEL index="5" value="2800" />
      <LABEL index="6" value="3200" />
      <LABEL index="7" value="3600" />
      <LABEL index="8" value="4000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC (corrected coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22A56" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%/deg</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x691" flags="0x30">
    <title>EVAP Purge Flow Model 1</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge flow model: the flow the PCM expects through the purge valve, by engine vacuum (rows, 0 to 80 kPa) and commanded purge (columns, 0 to 100 %). The EVAP leak test adds it up during its test phases and compares the total with its own limits to decide the phase. The PCM reads this table or EVAP Purge Flow Model 2 according to the state of one of its EVAP outputs. Shown raw. Reference only: changing it changes how the EVAP leak test judges the system and can hide or cause leak codes. DO NOT EDIT. Effect: reference only (EVAP leak test) Evidence: ledger:E0691, ledger:E0899, ledger:E0929, ledger:E0930</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>% (commanded evap purge)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="3.1" />
      <LABEL index="2" value="6.3" />
      <LABEL index="3" value="9.4" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="15.7" />
      <LABEL index="6" value="18.8" />
      <LABEL index="7" value="22.0" />
      <LABEL index="8" value="25.1" />
      <LABEL index="9" value="28.2" />
      <LABEL index="10" value="31.4" />
      <LABEL index="11" value="34.5" />
      <LABEL index="12" value="37.6" />
      <LABEL index="13" value="40.8" />
      <LABEL index="14" value="43.9" />
      <LABEL index="15" value="47.1" />
      <LABEL index="16" value="50.2" />
      <LABEL index="17" value="53.3" />
      <LABEL index="18" value="56.5" />
      <LABEL index="19" value="59.6" />
      <LABEL index="20" value="62.7" />
      <LABEL index="21" value="65.9" />
      <LABEL index="22" value="69.0" />
      <LABEL index="23" value="72.2" />
      <LABEL index="24" value="75.3" />
      <LABEL index="25" value="78.4" />
      <LABEL index="26" value="81.6" />
      <LABEL index="27" value="84.7" />
      <LABEL index="28" value="87.8" />
      <LABEL index="29" value="91.0" />
      <LABEL index="30" value="94.1" />
      <LABEL index="31" value="97.3" />
      <LABEL index="32" value="100.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>kPa (vacuum)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34DA4" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x692" flags="0x30">
    <title>EVAP Purge Flow Model 2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge flow model: the flow the PCM expects through the purge valve, by engine vacuum (rows, 0 to 80 kPa) and commanded purge (columns, 0 to 100 %). The EVAP leak test adds it up during its test phases and compares the total with its own limits to decide the phase. The PCM reads this table or EVAP Purge Flow Model 1 according to the state of one of its EVAP outputs. Shown raw. Reference only: changing it changes how the EVAP leak test judges the system and can hide or cause leak codes. DO NOT EDIT. Effect: reference only (EVAP leak test) Evidence: ledger:E0691, ledger:E0899, ledger:E0929, ledger:E0930</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>% (commanded evap purge)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="3.1" />
      <LABEL index="2" value="6.3" />
      <LABEL index="3" value="9.4" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="15.7" />
      <LABEL index="6" value="18.8" />
      <LABEL index="7" value="22.0" />
      <LABEL index="8" value="25.1" />
      <LABEL index="9" value="28.2" />
      <LABEL index="10" value="31.4" />
      <LABEL index="11" value="34.5" />
      <LABEL index="12" value="37.6" />
      <LABEL index="13" value="40.8" />
      <LABEL index="14" value="43.9" />
      <LABEL index="15" value="47.1" />
      <LABEL index="16" value="50.2" />
      <LABEL index="17" value="53.3" />
      <LABEL index="18" value="56.5" />
      <LABEL index="19" value="59.6" />
      <LABEL index="20" value="62.7" />
      <LABEL index="21" value="65.9" />
      <LABEL index="22" value="69.0" />
      <LABEL index="23" value="72.2" />
      <LABEL index="24" value="75.3" />
      <LABEL index="25" value="78.4" />
      <LABEL index="26" value="81.6" />
      <LABEL index="27" value="84.7" />
      <LABEL index="28" value="87.8" />
      <LABEL index="29" value="91.0" />
      <LABEL index="30" value="94.1" />
      <LABEL index="31" value="97.3" />
      <LABEL index="32" value="100.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>kPa (vacuum)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3520C" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x693" flags="0x30">
    <title>Idle Spark Maximum vs RPM vs Airmass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit on spark advance in idle spark mode, by engine speed (400 to 1600 rpm) and cylinder airmass. The coolant and intake temperature spark corrections are added to it and a weighted correction is taken off before it limits the idle spark. Stock 10 deg at 400 to 600 rpm rising to 25 deg at 1600 rpm on most of the airmass range, 27 deg at the lowest airmass. Effect: raise = more spark advance allowed at idle Evidence: ledger:E0692, ledger:E0825, ledger:E0931, ledger:E1219, ledger:E1641</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1000" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1400" />
      <LABEL index="6" value="1600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>index (airmass 0.08-1.36 g/cyl normalized 0-65535 via AEAC, E0825)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2D5D9" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X/2"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x694" flags="0x30">
    <title>Octane Scaler Start-Up Adjust vs Coolant and Intake Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added once at every engine start to each cylinder&#x27;s octane scaler, the share of the way from the High Octane toward the Low Octane spark table (0 to 1.0, also moved by octane learn). Negative moves toward High Octane. Stock -1.0 with a cold engine and cold intake, so a cold start begins on the High Octane table, rising to +0.10 when hot. Effect: raise = a start at that temperature moves the spark further toward the Low Octane table Evidence: ledger:E0296, ledger:E0695, ledger:E0937, ledger:E1218, ledger:E1641</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (ECT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>degC (IAT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AD98" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>fraction</units>
      <decimalpl>0</decimalpl>
      <min>-4.000000</min>
      <max>3.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x695" flags="0x30">
    <title>Airflow Model - MAF/VE Ratio Start Value vs Baro and Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starting value of the learned MAF-to-VE airmass ratio, by barometric pressure (columns, 65 to 105 kPa) and coolant temperature (rows, -20 to 101 C in 20.25 C steps). The engine then learns the ratio in steady running, clamped 0.5 to 1.5. Stock 1.05 to 1.25. Effect: raise = the learned MAF/VE airmass ratio starts higher at that baro / coolant, until steady-state learning corrects it Evidence: ledger:E0696, ledger:E0697, ledger:E0929</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="65" />
      <LABEL index="1" value="75" />
      <LABEL index="2" value="85" />
      <LABEL index="3" value="95" />
      <LABEL index="4" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>7</indexcount>
      <units>degC (ECT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-20.25" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="20.25" />
      <LABEL index="3" value="40.5" />
      <LABEL index="4" value="60.75" />
      <LABEL index="5" value="81" />
      <LABEL index="6" value="101.25" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B206" mmedelementsizebits="16" mmedrowcount="7" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio (MAF / VE)</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x696" flags="0x30">
    <title>EVAP Engine-Off Test - Reference Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP small leak test (P0442): reference tank reading by ambient air temperature (rows, -10 to 80 C) and fuel level (columns, 0 to 100 %). The pressure phase is complete as soon as the tank reading reaches this, and the leak result is the shortfall of the pressure-to-vacuum swing against it. Stock -2.5 inH2O in every cell (2.5 inH2O of pressure; vacuum is positive, pressure negative). Changing it changes when the test passes or sets P0442. Effect: more negative = more tank pressure is needed for a full pass Evidence: ledger:E0698, ledger:E0899, ledger:E0935, ledger:E0936, ledger:E0939, ledger:E0944, ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC (ambient air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-10" />
      <LABEL index="1" value="-4.375" />
      <LABEL index="2" value="1.25" />
      <LABEL index="3" value="6.875" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.125" />
      <LABEL index="6" value="23.75" />
      <LABEL index="7" value="29.375" />
      <LABEL index="8" value="35" />
      <LABEL index="9" value="40.625" />
      <LABEL index="10" value="46.25" />
      <LABEL index="11" value="51.875" />
      <LABEL index="12" value="57.5" />
      <LABEL index="13" value="63.125" />
      <LABEL index="14" value="68.75" />
      <LABEL index="15" value="74.375" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33D64" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>inH2O</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x697" flags="0x30">
    <title>EVAP Engine-Off Test - Reference Pressure (service test)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP small leak test (P0442): the same reference for the scan tool started version of the test while its ambient temperature estimate is not yet valid, by ambient air temperature (rows, -10 to 80 C) and fuel level (columns, 0 to 100 %). Stock -2.5 inH2O in every cell (2.5 inH2O of pressure; vacuum is positive, pressure negative). Effect: more negative = more tank pressure is needed for a full pass Evidence: ledger:E0698, ledger:E0899, ledger:E0935, ledger:E0936, ledger:E0939, ledger:E0944, ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC (ambient air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-10" />
      <LABEL index="1" value="-4.375" />
      <LABEL index="2" value="1.25" />
      <LABEL index="3" value="6.875" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.125" />
      <LABEL index="6" value="23.75" />
      <LABEL index="7" value="29.375" />
      <LABEL index="8" value="35" />
      <LABEL index="9" value="40.625" />
      <LABEL index="10" value="46.25" />
      <LABEL index="11" value="51.875" />
      <LABEL index="12" value="57.5" />
      <LABEL index="13" value="63.125" />
      <LABEL index="14" value="68.75" />
      <LABEL index="15" value="74.375" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3403C" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>inH2O</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x698" flags="0x30">
    <title>Catalyst Monitor - Storage Time Normaliser, Bank 2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier applied to the measured catalyst oxygen storage time before it is compared with the storage time reference, by mean airflow during the lean fuel step (columns, 0 to 16 g/s) and modelled catalyst temperature (rows, 300 to 800 C). Higher values make the catalyst look better, so the efficiency code is less likely. Used only for a second catalyst bank; this calibration has one bank: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0699, ledger:E1021, ledger:E1191</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s (mean airflow over the test step)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.5" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="1.5" />
      <LABEL index="4" value="2" />
      <LABEL index="5" value="2.5" />
      <LABEL index="6" value="3" />
      <LABEL index="7" value="3.5" />
      <LABEL index="8" value="4" />
      <LABEL index="9" value="4.5" />
      <LABEL index="10" value="5" />
      <LABEL index="11" value="5.5" />
      <LABEL index="12" value="6" />
      <LABEL index="13" value="6.5" />
      <LABEL index="14" value="7" />
      <LABEL index="15" value="7.5" />
      <LABEL index="16" value="8" />
      <LABEL index="17" value="8.5" />
      <LABEL index="18" value="9" />
      <LABEL index="19" value="9.5" />
      <LABEL index="20" value="10" />
      <LABEL index="21" value="10.5" />
      <LABEL index="22" value="11" />
      <LABEL index="23" value="11.5" />
      <LABEL index="24" value="12" />
      <LABEL index="25" value="12.5" />
      <LABEL index="26" value="13" />
      <LABEL index="27" value="13.5" />
      <LABEL index="28" value="14" />
      <LABEL index="29" value="14.5" />
      <LABEL index="30" value="15" />
      <LABEL index="31" value="15.5" />
      <LABEL index="32" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>degC (catalyst temperature model)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="300" />
      <LABEL index="1" value="362.5" />
      <LABEL index="2" value="425" />
      <LABEL index="3" value="487.5" />
      <LABEL index="4" value="550" />
      <LABEL index="5" value="612.5" />
      <LABEL index="6" value="675" />
      <LABEL index="7" value="737.5" />
      <LABEL index="8" value="800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x32B23" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x699" flags="0x30">
    <title>Purge Valve Duty vs Flow Demand</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge: purge valve duty for the purge flow demand (0 to 163 flow units; the demand is the flow request times the manifold vacuum factor). Stock 10 % at no demand rising to 100 %. Purge flow units: the full scale word (stock 123) is full purge reference flow. Effect: raise = more valve opening for that flow demand Evidence: ledger:E1122</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>flow units demand</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5.094" />
      <LABEL index="2" value="10.188" />
      <LABEL index="3" value="15.281" />
      <LABEL index="4" value="20.375" />
      <LABEL index="5" value="25.469" />
      <LABEL index="6" value="30.562" />
      <LABEL index="7" value="35.656" />
      <LABEL index="8" value="40.75" />
      <LABEL index="9" value="45.844" />
      <LABEL index="10" value="50.938" />
      <LABEL index="11" value="56.031" />
      <LABEL index="12" value="61.125" />
      <LABEL index="13" value="66.219" />
      <LABEL index="14" value="71.312" />
      <LABEL index="15" value="76.406" />
      <LABEL index="16" value="81.5" />
      <LABEL index="17" value="86.594" />
      <LABEL index="18" value="91.688" />
      <LABEL index="19" value="96.781" />
      <LABEL index="20" value="101.875" />
      <LABEL index="21" value="106.969" />
      <LABEL index="22" value="112.062" />
      <LABEL index="23" value="117.156" />
      <LABEL index="24" value="122.25" />
      <LABEL index="25" value="127.344" />
      <LABEL index="26" value="132.438" />
      <LABEL index="27" value="137.531" />
      <LABEL index="28" value="142.625" />
      <LABEL index="29" value="147.719" />
      <LABEL index="30" value="152.812" />
      <LABEL index="31" value="157.906" />
      <LABEL index="32" value="163" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24FC6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.781250</max>
      <MATH equation="X/326.4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x69A" flags="0x30">
    <title>Misfire - Catalyst Damage Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: misfire rate (misfires per 100 cylinder firings, measured over 200 engine revolutions) at or above which the window counts as catalyst damaging. Looked up at the engine speed and load of the start and of the end of the window; the larger limit is used. Stock 18 % at low speed and load falling to 5 % at high speed or load. Effect: raise = more misfire is tolerated before the catalyst-damage decision and the flashing lamp Evidence: ledger:E0707, ledger:E0929, ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1000" />
      <LABEL index="2" value="2000" />
      <LABEL index="3" value="3000" />
      <LABEL index="4" value="4000" />
      <LABEL index="5" value="5000" />
      <LABEL index="6" value="6000" />
      <LABEL index="7" value="7000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>11</indexcount>
      <units>% load</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3707E" mmedelementsizebits="16" mmedrowcount="11" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x69B" flags="0x30">
    <title>Commanded Mixture Lean Offset vs Temperature A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded air-fuel mixture is pulled leaner as the engine warms: this curve sets how much richness is subtracted from the commanded mixture at each modelled engine temperature, from a small offset near -40 C (0.10 equivalence ratio) up to a large offset by 216 C (0.90), floored so the mixture is never commanded leaner than a 1:1 equivalence ratio. One of two selectable variants; this is variant A. 1x33 curve, -40 to 216 C in 8-degree steps. Effect: raise = more richness subtracted at that temperature (mixture commanded leaner, down to the 1:1 floor) Evidence: ledger:E0711</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26ECE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ ratio offset</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x69C" flags="0x30">
    <title>Commanded Mixture Lean Offset vs Temperature B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded air-fuel mixture is pulled leaner as the engine warms: this curve sets how much richness is subtracted from the commanded mixture at each modelled engine temperature, from a small offset near -40 C (0.10 equivalence ratio) up to a large offset by 216 C (0.90), floored so the mixture is never commanded leaner than a 1:1 equivalence ratio. One of two selectable variants; this is variant B (identical stock data to variant A). 1x33 curve, -40 to 216 C in 8-degree steps. Effect: raise = more richness subtracted at that temperature (mixture commanded leaner, down to the 1:1 floor) Evidence: ledger:E0711</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26F16" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ ratio offset</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x69D" flags="0x0">
    <title>Spark Ceiling - Hot Mode Minimum Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The hot high-load spark ceiling can only arm while coolant is above this temperature. Stock 85 C. Effect: lower = the ceiling arms on a cooler engine Evidence: ledger:E0719</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x3023A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x69E" flags="0x0">
    <title>Spark Ceiling - Hot Mode Hold RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once armed, the hot high-load spark ceiling stays active while rpm stays above this value (with the coolant and load conditions). Stock 3000 rpm. Effect: raise = the ceiling drops out at a higher rpm Evidence: ledger:E0719</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x3023C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x69F" flags="0x0">
    <title>Spark Ceiling - Hot Mode Entry RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The hot high-load spark ceiling starts arming only above this rpm (with the coolant and load conditions). Stock 3200 rpm. Effect: raise = the ceiling arms only at higher rpm Evidence: ledger:E0719</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x3023E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A0" flags="0x0">
    <title>Spark Ceiling - Hot Mode Arm Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the hot, high-rpm, high-load condition must last before the lower spark ceiling takes over; it releases after the same time counts back down. Stock 18.0 s. Effect: raise = the ceiling engages later in a long pull Evidence: ledger:E0719</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x3015C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A1" flags="0x0">
    <title>Spark Reference - Shortfall Confirm Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long delivered spark must stay below the Spark Reference for Cam Target Reduction table before the cam target reduction starts stepping down (it stops as soon as spark is back at or above the reference). Stock 0.5 s. Effect: raise = spark must fall short for longer before the cam target is reduced Evidence: ledger:E0720, ledger:E0733, ledger:E0875, ledger:E0932</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x3015E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A2" flags="0x0">
    <title>Spark Reference - Cam Phase Adder Gain (inactive) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Gain on the cam phase term added to the airmass x rpm spark reference. The cam phase input is always 0 on the stock H3, so this has no effect. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (no effect on the stock H3) Evidence: ledger:E0720, ledger:E0899</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x30160" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A3" flags="0x0">
    <title>Cam Phaser Learned Gain Slot - RPM Split</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cam phaser controller keeps 12 learned gain multipliers and picks one by the direction of the cam error, engine speed above or below the speed split, and coolant cold, middle or hot. Above this engine speed the upper-speed slots are used. Stock 1700 rpm. Effect: moves the engine speed where the controller switches slots Evidence: ledger:E0737, ledger:E0837, ledger:E0842</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22BD0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A4" flags="0x0">
    <title>Cam Phaser Learned Gain Slot - Hot Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cam phaser controller keeps 12 learned gain multipliers and picks one by the direction of the cam error, engine speed above or below the speed split, and coolant cold, middle or hot. Above this coolant temperature the hot slots are used. Stock 96.5 C. Effect: moves where the hot slots take over Evidence: ledger:E0737, ledger:E0837, ledger:E0842</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22BD2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A5" flags="0x0">
    <title>Cam Phaser Learned Gain Slot - Cold Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cam phaser controller keeps 12 learned gain multipliers and picks one by the direction of the cam error, engine speed above or below the speed split, and coolant cold, middle or hot. Below this coolant temperature the cold slots are used. Stock 83 C. Effect: moves where the cold slots take over Evidence: ledger:E0737, ledger:E0837, ledger:E0842</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22BD4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A6" flags="0x0">
    <title>Cam Phaser Stuck Response - Stage 1 Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phaser stuck response: when the cam is commanded to at least 4 degrees but has not moved past 1.5 degrees (or on a second internal trigger), the PCM pulses the phaser solenoid: stage 1 duty for the stage 1 time, then stage 2 duty for the stage 2 time, repeated up to the pulse repeat count. This is how long each pulse holds the stage 1 duty. Stock 0.0625 s. Effect: raise = longer stage 1 pulse Evidence: ledger:E0737, ledger:E0837</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22CA0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A7" flags="0x0">
    <title>Cam Phaser Stuck Response - Stage 1 Duty</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phaser stuck response: when the cam is commanded to at least 4 degrees but has not moved past 1.5 degrees (or on a second internal trigger), the PCM pulses the phaser solenoid: stage 1 duty for the stage 1 time, then stage 2 duty for the stage 2 time, repeated up to the pulse repeat count. This is the solenoid duty during stage 1 (100 % is full on). Stock 100 %. Effect: lower = gentler stage 1 pulse Evidence: ledger:E0737, ledger:E0837</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22CA2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A8" flags="0x0">
    <title>Cam Phaser Stuck Response - Stage 2 Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phaser stuck response: when the cam is commanded to at least 4 degrees but has not moved past 1.5 degrees (or on a second internal trigger), the PCM pulses the phaser solenoid: stage 1 duty for the stage 1 time, then stage 2 duty for the stage 2 time, repeated up to the pulse repeat count. This is how long each pulse holds the stage 2 duty. Stock 0.0625 s. Effect: raise = longer stage 2 pulse Evidence: ledger:E0737, ledger:E0837</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22CA4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A9" flags="0x0">
    <title>Cam Phaser Stuck Response - Stage 2 Duty</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phaser stuck response: when the cam is commanded to at least 4 degrees but has not moved past 1.5 degrees (or on a second internal trigger), the PCM pulses the phaser solenoid: stage 1 duty for the stage 1 time, then stage 2 duty for the stage 2 time, repeated up to the pulse repeat count. This is the solenoid duty during stage 2. Stock 0 % (off). Effect: raise = stage 2 no longer releases the solenoid fully Evidence: ledger:E0737, ledger:E0837</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22CA6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6AA" flags="0x0">
    <title>Cam Phasing Enable - Coolant On Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phasing is allowed only while all of its enable conditions hold. The coolant condition turns on above this temperature. Stock -10 C. Effect: raise = cam phasing waits for a warmer engine Evidence: ledger:E0738</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22D16" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6AB" flags="0x0">
    <title>Cam Phasing Enable - Coolant Off Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phasing is allowed only while all of its enable conditions hold. The coolant condition turns off again below this temperature. Stock -13 C. Effect: raise = cam phasing drops out sooner as the engine cools Evidence: ledger:E0738</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22D18" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6AC" flags="0x0">
    <title>Cam Phasing Enable - Throttle Thresholds RPM Split</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phasing is allowed only while all of its enable conditions hold. Below this engine speed the low-rpm throttle thresholds apply, at or above it the high-rpm pair. Stock 950 rpm. Effect: moves where the high-rpm throttle thresholds take over Evidence: ledger:E0738</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22D1A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6AD" flags="0x0">
    <title>Cam Phasing Enable - Throttle Off Below (low rpm)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phasing is allowed only while all of its enable conditions hold. Below the split rpm the throttle condition turns off when throttle falls below this. Stock 0.20 %. Effect: raise = cam phasing drops out at a more open throttle at low rpm Evidence: ledger:E0738</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22D1C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6AE" flags="0x0">
    <title>Cam Phasing Enable - Throttle On Above (low rpm)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phasing is allowed only while all of its enable conditions hold. Below the split rpm the throttle condition turns on when throttle rises above this. Stock 0.80 %. Effect: raise = cam phasing needs more throttle at low rpm Evidence: ledger:E0738</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22D1E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6AF" flags="0x0">
    <title>Cam Phasing Enable - Throttle Off Below (high rpm)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phasing is allowed only while all of its enable conditions hold. At or above the split rpm the throttle condition turns off when throttle falls below this. Stock 0 %, so it never turns off there. Effect: raise = cam phasing can drop out on a closed throttle above the split rpm Evidence: ledger:E0738</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22D20" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6B0" flags="0x0">
    <title>Cam Phasing Enable - Throttle On Above (high rpm)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phasing is allowed only while all of its enable conditions hold. At or above the split rpm the throttle condition turns on when throttle rises above this. Stock 0.80 %. Effect: raise = cam phasing needs more throttle above the split rpm Evidence: ledger:E0738</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22D22" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6B1" flags="0x0">
    <title>Cam Phasing Enable - Vehicle Speed On At</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phasing is allowed only while all of its enable conditions hold. The vehicle speed condition turns on at or above this speed. Stock 1.0 km/h. Effect: raise = cam phasing waits for a higher road speed Evidence: ledger:E0738</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22D6C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6B2" flags="0x0">
    <title>Cam Phasing Enable - Vehicle Speed Off Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phasing is allowed only while all of its enable conditions hold. The vehicle speed condition turns off below this speed. Stock 0.5 km/h. Effect: raise = cam phasing drops out at a higher road speed Evidence: ledger:E0738</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22D6E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6B3" flags="0x0">
    <title>Cam Phasing Enable - MAP Threshold Pair Baro Split</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phasing is allowed only while all of its enable conditions hold. At or above this barometric pressure the sea-level pair of MAP on / off thresholds is used (pair B), below it the altitude pair (pair A). Stock 90 kPa. Effect: moves the altitude at which the altitude MAP thresholds take over Evidence: ledger:E0738</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22D70" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6B4" flags="0x0">
    <title>EVAP Purge - Fallback Duty</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded EVAP purge used when neither purge control feature is active. Stock 0 %, so purge is off in that case. Effect: raise = purge runs in the fallback case Evidence: ledger:E0739</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x24F94" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6B5" flags="0x0">
    <title>EVAP Purge - Ramp Deadband</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded EVAP purge only moves toward its target once the gap is at least this; smaller gaps leave it where it is. Stock 2.0 %. Effect: raise = purge ignores larger target changes Evidence: ledger:E0739</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x24F96" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6B6" flags="0x0">
    <title>EVAP Purge - Ramp Tables Speed Split</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or above this vehicle speed the highway pair of purge ramp tables is used, below it the low-speed pair. Stock 50 km/h. Effect: moves where the highway purge ramp rates take over Evidence: ledger:E0739</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x24F98" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x6B7" flags="0x30">
    <title>Idle Load State - Park/Neutral Delay Below Split Speed vs Trans Temp (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle tables, Park / Neutral or in gear rows: delay after a shift to Park / Neutral before the Park / Neutral rows are used, by transmission fluid temperature, below the split speed. The split speed is 0 on stock, so this curve is never used. Effect: no effect on this truck Evidence: ledger:E0293, ledger:E0742, ledger:E1113</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A778" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6B8" flags="0x30">
    <title>Idle Load State - In Gear Time-Out vs Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle tables, Park / Neutral or in gear rows: longest time after a shift into gear before the in gear rows of all idle tables are used, by transmission fluid temperature. They are used earlier when engine speed has dropped to the in gear confirm ratio. Stock 3.0 s cold down to 0.3 s warm. Effect: raise = the Park / Neutral rows stay in use longer after a shift into gear Evidence: ledger:E0293, ledger:E0742, ledger:E1113</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A79C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6B9" flags="0x30">
    <title>Idle Airflow Shift into P/N Kick Factor, Extended Term, vs Trans Temp (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: factor on the extended part of the kick, by transmission fluid temperature. Stock 1.0. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck, so it has no effect. Effect: no effect on this truck Evidence: ledger:E0293, ledger:E0742, ledger:E1113</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A6C4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6BA" flags="0x30">
    <title>Idle Airflow Shift into Gear Kick Factor, Extended Term, vs Trans Temp (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into gear: factor on the extended part of the kick, by transmission fluid temperature. Stock 1.0. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck, so it has no effect. Effect: no effect on this truck Evidence: ledger:E0293, ledger:E0742, ledger:E1113</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A70C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6BB" flags="0x30">
    <title>Shift into Gear Idle Kick, Extended Term Re-Arm Threshold vs Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into gear: the extended part switches back on once transmission input speed has risen more than this since the shift, by transmission fluid temperature. Stock 100 rpm cold rising to 260 rpm hot. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0742, ledger:E1113, ledger:E1187</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A6A0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x6BC" flags="0x0">
    <title>Spark Mode Ramp - Decel Fuel Cut End to Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark reference ramp: when the spark mode changes (cranking, idle, first idle after start, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This value is the ramp from decel fuel cut back to idle (fuel cut ending, first-idle flag set, idle speed control on). Stock 35. Effect: raise = slower spark change on this transition Evidence: ledger:E0747, ledger:E0894</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F190" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>update cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6BD" flags="0x0">
    <title>Spark Reference Ramp Duration, Fixed Value B (inactive, unused spark mode)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this ramp duration belongs to a spark mode that no code ever selects. Spark reference ramp: when the spark mode changes (cranking, idle, first idle after start, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). Dormant: no effect on this truck&#x27;s software. Effect: no effect Evidence: ledger:E0747, ledger:E0894</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F192" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6BE" flags="0x0">
    <title>Spark Reference Ramp Duration, Fixed Value C (inactive, unused spark mode)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this ramp duration belongs to a spark mode that no code ever selects. Spark reference ramp: when the spark mode changes (cranking, idle, first idle after start, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). Dormant: no effect on this truck&#x27;s software. Effect: no effect Evidence: ledger:E0747, ledger:E0894</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F194" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6BF" flags="0x0">
    <title>Spark Mode Ramp - First Idle to Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark reference ramp: when the spark mode changes (cranking, idle, first idle after start, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This value is the ramp from first idle after start to idle once closed-throttle idle speed control takes over. Stock 25. Effect: raise = slower spark change on this transition Evidence: ledger:E0747, ledger:E0894</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F196" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>update cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C0" flags="0x0">
    <title>Spark Mode Ramp - First Idle to Off Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark reference ramp: when the spark mode changes (cranking, idle, first idle after start, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This value is the ramp from first idle after start to off idle (throttle rpm controller engaged, or the first-idle flag cleared). Stock 25. Effect: raise = slower spark change on this transition Evidence: ledger:E0747, ledger:E0894</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F1B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>update cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C1" flags="0x0">
    <title>Spark Mode Ramp - Off Idle to Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark reference ramp: when the spark mode changes (cranking, idle, first idle after start, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This value is the ramp from off idle to idle once closed-throttle idle speed control takes over. Stock 5. Effect: raise = slower spark change on this transition Evidence: ledger:E0747, ledger:E0894</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F1B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>update cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C2" flags="0x0">
    <title>Spark Mode Ramp - Idle to First Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark reference ramp: when the spark mode changes (cranking, idle, first idle after start, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This value is the ramp from idle into first idle after start (first-idle flag set, throttle rpm controller off, idle gate set). Stock 75. Effect: raise = slower spark change on this transition Evidence: ledger:E0747, ledger:E0894</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F1E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>update cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C3" flags="0x0">
    <title>Spark Mode Ramp - Off Idle to First Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark reference ramp: when the spark mode changes (cranking, idle, first idle after start, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This value is the ramp from off idle to first idle after start (first-idle flag set). Stock 50. Effect: raise = slower spark change on this transition Evidence: ledger:E0747, ledger:E0894</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F1E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>update cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C4" flags="0x0">
    <title>Spark Mode Ramp - Decel Fuel Cut End to First Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark reference ramp: when the spark mode changes (cranking, idle, first idle after start, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This value is the ramp from decel fuel cut to first idle after start (fuel cut ending, first-idle flag set, idle speed control off). Stock 35. Effect: raise = slower spark change on this transition Evidence: ledger:E0747, ledger:E0894</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F1E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>update cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C5" flags="0x0">
    <title>Spark Reference Settle Duration, Fixed Value D (inactive, unused spark mode)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this ramp duration belongs to a spark mode that no code ever selects. Spark reference ramp: when the spark mode changes (cranking, idle, first idle after start, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). Dormant: no effect on this truck&#x27;s software. Effect: no effect Evidence: ledger:E0747, ledger:E0894</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F1EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x6C6" flags="0x30">
    <title>Spark Mode Ramp - Cranking to Idle vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark reference ramp: when the spark mode changes (cranking, idle, first idle after start, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This curve is the ramp from cranking to idle once the engine is running, by coolant temperature. Stock 25 cycles when cold, 5 cycles from 40 C. Effect: raise = slower spark change after the engine starts Evidence: ledger:E0747, ledger:E0894, ledger:E1641</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>degC (ECT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <LABEL index="9" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F17C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>update cycles</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6C7" flags="0x30">
    <title>Spark Mode Ramp - Idle to Off Idle vs Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark reference ramp: when the spark mode changes (cranking, idle, first idle after start, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This curve is the ramp from idle to off idle, by throttle when the change happens. Stock 9 cycles up to 30 %, falling to 0 from 80 %. Effect: raise = slower spark change on this transition Evidence: ledger:E0747, ledger:E0894, ledger:E0895</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>% throttle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F19A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>update cycles</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6C8" flags="0x30">
    <title>Spark Mode Ramp - Decel Fuel Cut End to Off Idle vs Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark reference ramp: when the spark mode changes (cranking, idle, first idle after start, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This curve is the ramp from decel fuel cut back to off idle, by throttle. Stock 37 cycles at closed throttle falling to 9 from 70 %. Effect: raise = slower spark change on this transition Evidence: ledger:E0747, ledger:E0894, ledger:E0895</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>% throttle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F1B6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>update cycles</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6C9" flags="0x30">
    <title>Spark Mode Ramp - Into Decel Fuel Cut vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark reference ramp: when the spark mode changes (cranking, idle, first idle after start, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This curve is the ramp into decel fuel cut (from off idle or first idle), by engine speed. Stock 64 cycles at every speed. Effect: raise = slower spark change on this transition Evidence: ledger:E0747, ledger:E0894, ledger:E0895</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F1F0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>update cycles</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6CA" flags="0x30">
    <title>Tip-In Spark Advance - Hold Time vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in spark advance (spark advance added for a short time when cylinder airmass jumps): time the advance is held at full size before it starts to decay, by coolant. Stock 0.7 s cold falling to 0 from 80 C. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = the advance is held longer Evidence: ledger:E1142</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CD34" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6CB" flags="0x30">
    <title>Tip-In Spark Advance - Decay Step vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in spark advance (spark advance added for a short time when cylinder airmass jumps): rate at which the advance is taken out again after the hold time, by coolant (one step every 12.5 ms). Stock 3 to 7.5 degrees per second. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = the advance is removed faster Evidence: ledger:E1142</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CDA8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg/s</units>
      <decimalpl>1</decimalpl>
      <min>-20480.000000</min>
      <max>20479.375000</max>
      <MATH equation="X*0.625"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x6CC" flags="0x0">
    <title>Idle Airflow Kick - Shift into P/N Re-Arm Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: wait after the kick has faded before another one can be given. Stock 1 s. Effect: raise = longer wait between kicks Evidence: ledger:E1113</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A64A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6CD" flags="0x0">
    <title>Shift into Park/Neutral Idle Kick, Reset Debounce Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On a fresh shift into Park or Neutral, this is the minimum time the shift-into-gear kick timer must already have been counting before the Park/Neutral kick&#x27;s own hold timer is reset. Stock 0.03 seconds. Effect: raise = a fresh Park/Neutral shift is less likely to reset the hold timer Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A648" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6CE" flags="0x0">
    <title>Shift into Gear Idle Kick, Reset Debounce Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On a fresh shift into gear, this is the minimum time the Park/Neutral kick timer must already have been counting before the shift-into-gear kick&#x27;s own hold timer is reset. Stock 0.03 seconds. Effect: raise = a fresh gear shift is less likely to reset the hold timer Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A654" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6CF" flags="0x0">
    <title>Shift into Park/Neutral Idle Kick, Extended Term Delay (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: time in Park / Neutral before the extended part of the kick switches on. Stock 0.05 s. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck, so it has no effect. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E1113</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A64E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D0" flags="0x0">
    <title>Shift into Gear Idle Kick, Settle Timer Maximum Duration</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Longest time the shift-into-gear idle-kick settle timer is allowed to keep running before it stops and clears its own internal flags. Stock 1.0 seconds. Effect: raise = the settle timer is allowed to run longer before it is forced to stop Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A650" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D1" flags="0x0">
    <title>Idle Airflow Adaptive Follower, Arm Throttle Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle position, at or below which the idle-air adaptive follower system is allowed to arm. Stock 0.0 percent. Effect: raise = the follower can arm at a higher throttle position Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A9AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D2" flags="0x0">
    <title>Idle Airflow Adaptive Follower, Disarm Throttle Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the arm throttle floor to set the throttle position above which an already-armed idle-air adaptive follower is disarmed and reset. Stock 0.0 percent. Effect: raise = the follower stays armed at a higher throttle position Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A9AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D3" flags="0x0">
    <title>Idle Airflow Adaptive Follower, Throttle Tracking Slew Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Maximum amount, in throttle percent, that the follower&#x27;s internal throttle-tracking figure is allowed to change on each pass. Stock 0.0 percent, which on this vehicle means that tracked figure never changes once initialized. Effect: raise = the tracked figure can change faster from one pass to the next Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A9A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x6D4" flags="0x30">
    <title>Idle Airflow Adaptive Follower, Throttle Bucket Points</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle-position break points used to sort the current throttle position into a bucket for the adaptive follower&#x27;s throttle correction. Cells are throttle percent values, not an output curve. Effect: n/a (breakpoint definition, not an output curve) Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AA78" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6D5" flags="0x30">
    <title>Idle Airflow Adaptive Follower, Barometric Pressure Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the idle-air adaptive follower&#x27;s airflow build-up by barometric pressure. Stock 1.0 at every pressure point on this bin. Effect: raise = bigger follower airflow contribution at that pressure Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A9F8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x6D6" flags="0x0">
    <title>Shift to Park/Neutral Idle Kick, Hold Time Table Split Speed (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Picks which of two duration tables sets how long the extra part of the Park/Neutral idle-air bump keeps running: below this vehicle speed the 5-second table, at or above it an all-zero table. Stock 0 km/h, so the all-zero table is always picked and the extra part switches off at once on this truck (inactive). Effect: raise = allows the extended term at higher speeds Evidence: ledger:E0750, ledger:E1147</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A642" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D7" flags="0x0">
    <title>Idle Airflow Kick - Shift into Gear RPM Margin</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into gear: the kick is given only when engine speed is not more than this above desired idle. Stock 200 rpm. Effect: raise = the kick is also given at higher engine speed Evidence: ledger:E1113</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A63C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D8" flags="0x0">
    <title>Idle Load State - In Gear Confirm RPM Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle tables, Park / Neutral or in gear rows: after a shift into gear the in gear rows are used as soon as engine speed has fallen to this share of the engine speed at the shift (or when the time-out runs out). Stock 0.90. Effect: lower = a larger rpm drop is needed before the in gear rows are used Evidence: ledger:E1113</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A63E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D9" flags="0x0">
    <title>Shift to Park/Neutral Idle Kick, Extended Term Re-Arm Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: the extended part switches back on once converter clutch slip is below this. Stock 50 rpm. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E1113, ledger:E1187</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A63A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6DA" flags="0x0">
    <title>Shift into Gear Idle Kick, Extended Term Speed Gate (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into gear: highest vehicle speed at the shift for the extended part of the kick. Stock 5 km/h. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck, so it has no effect. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E0898, ledger:E1113</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A646" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6DB" flags="0x0">
    <title>Shift to Park/Neutral Idle Kick, Extended Term Speed Gate (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: highest vehicle speed at the shift for the extended part of the kick. Stock 15 km/h. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck, so it has no effect. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E0898, ledger:E1113</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A644" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6DC" flags="0x0">
    <title>Idle Airflow Kick - Shift into P/N Fade Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: share of the remaining kick removed every 12.5 ms once its duration is over. Stock 0.5: it halves each pass. Effect: raise = the kick fades faster Evidence: ledger:E1113</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A634" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6DD" flags="0x0">
    <title>Idle Airflow Kick - Shift into Gear Fade Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into gear: share of the remaining kick removed every 12.5 ms once its duration is over. Stock 0: the kick ends at once. Effect: raise from 0 = the kick fades out instead of ending at once (0.5 halves it each pass) Evidence: ledger:E1113</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A636" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6DE" flags="0x0">
    <title>Idle Airflow Kick - Shift into P/N RPM Margin</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: the kick is given only when engine speed is not more than this above desired idle. Stock 100 rpm. Effect: raise = the kick is also given at higher engine speed Evidence: ledger:E1113</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A638" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6DF" flags="0x0">
    <title>Shift into Gear Idle Kick, Base Amount Bias</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into gear: added to the turbine speed fall rate before the extended kick amount is looked up. Stock 2 rpm/s. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E1113, ledger:E1187</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A632" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm/s</units>
    <decimalpl>1</decimalpl>
    <min>-8000.000000</min>
    <max>7999.755859</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4.096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6E0" flags="0x0">
    <title>Shift to Park/Neutral Idle Kick, Base Amount Bias</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: added to the turbine speed fall rate before the extended kick amount is looked up. Stock 2 rpm/s. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E1113, ledger:E1187</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A630" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm/s</units>
    <decimalpl>1</decimalpl>
    <min>-8000.000000</min>
    <max>7999.755859</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4.096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x6E1" flags="0x30">
    <title>Idle Airflow Kick - Shift into Gear Extended Amount vs Turbine Speed Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into gear: extra airflow added by the extended part of the kick, by how fast the turbine speed is falling, plus the bias. Stock 0. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E0936, ledger:E1113, ledger:E1187</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm/s (turbine speed fall rate + bias)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-8000" />
      <LABEL index="1" value="-7000" />
      <LABEL index="2" value="-6000" />
      <LABEL index="3" value="-5000" />
      <LABEL index="4" value="-4000" />
      <LABEL index="5" value="-3000" />
      <LABEL index="6" value="-2000" />
      <LABEL index="7" value="-1000" />
      <LABEL index="8" value="0" />
      <LABEL index="9" value="1000" />
      <LABEL index="10" value="2000" />
      <LABEL index="11" value="3000" />
      <LABEL index="12" value="4000" />
      <LABEL index="13" value="5000" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="7000" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A67C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6E2" flags="0x30">
    <title>Idle Airflow Kick - Shift into P/N Extended Amount vs Turbine Speed Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: extra airflow added by the extended part of the kick, by how fast the turbine speed is falling, plus the bias. Stock 0. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E0936, ledger:E1113, ledger:E1187</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm/s (turbine speed fall rate + bias)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-8000" />
      <LABEL index="1" value="-7000" />
      <LABEL index="2" value="-6000" />
      <LABEL index="3" value="-5000" />
      <LABEL index="4" value="-4000" />
      <LABEL index="5" value="-3000" />
      <LABEL index="6" value="-2000" />
      <LABEL index="7" value="-1000" />
      <LABEL index="8" value="0" />
      <LABEL index="9" value="1000" />
      <LABEL index="10" value="2000" />
      <LABEL index="11" value="3000" />
      <LABEL index="12" value="4000" />
      <LABEL index="13" value="5000" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="7000" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A658" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x6E3" flags="0x0">
    <title>Idle Airflow Adaptive Follower, Arm Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle airflow follower may arm only while measured throttle area above the idle area is at or below this (and throttle is at or below the arm throttle floor). Stock 0.006 %. Effect: raise = the follower may arm with more throttle area open Evidence: ledger:E0750, ledger:E1137, ledger:E1187</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A9A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x6E4" flags="0x30">
    <title>Throttle Follower Factor vs Speed (cruise engaged)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the follower target vs vehicle speed while cruise control is engaged (the other table is used otherwise). Stock 0.68 at 0 to 14 km/h, 1.0 above. Part of the idle throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. Effect: raise = more follower air after a lift while cruise control is engaged Evidence: ledger:E0292, ledger:E0750, ledger:E0838, ledger:E1187</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="14" />
      <LABEL index="2" value="28" />
      <LABEL index="3" value="42" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="70" />
      <LABEL index="6" value="84" />
      <LABEL index="7" value="98" />
      <LABEL index="8" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AAB0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>3.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6E5" flags="0x30">
    <title>Throttle Follower Decay Step Limit vs Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit on the follower decay step, by throttle position (0 to 100 %). Stock no limit (32 g/s). Part of the idle throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. Effect: lower = follower air bleeds off more slowly at that throttle Evidence: ledger:E0292, ledger:E0750, ledger:E1187</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% throttle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A9B0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s per update</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>31.999512</max>
      <MATH equation="X/2048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6E6" flags="0x30">
    <title>Throttle Follower Rise Step Limit vs Throttle Area</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most the follower air may rise per update, by measured throttle area above the idle area (0 to 100 %). Stock 32 g/s (no limit). Part of the idle throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. Effect: lower = follower air builds up more slowly Evidence: ledger:E0750, ledger:E0936, ledger:E1137, ledger:E1187</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% throttle area</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A9D4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s per update</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6E7" flags="0x30">
    <title>COT enrichment arm load threshold vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once engine speed is above roughly 3200 rpm, this sets the engine load (in cylinder airmass) that must be exceeded, together with coolant hotter than 85 C sustained for 15 seconds, before the coolant over-temperature (COT) enrichment is allowed to switch on. Stock is a flat 0.670 grams per cylinder at every speed point from 1600 to 8000 rpm. Protection enrichment - DO NOT TUNE. Effect: protection enrichment Evidence: ledger:E0752, ledger:E1641</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1600" />
      <LABEL index="1" value="2400" />
      <LABEL index="2" value="3200" />
      <LABEL index="3" value="4000" />
      <LABEL index="4" value="4800" />
      <LABEL index="5" value="5600" />
      <LABEL index="6" value="6400" />
      <LABEL index="7" value="7200" />
      <LABEL index="8" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26D46" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/cyl (airmass)</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8.191875</max>
      <MATH equation="X/8000"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6E8" flags="0x30">
    <title>COT enrichment hold load threshold vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the coolant over-temperature (COT) enrichment has already switched on, this is the (slightly lower) engine load ceiling, above roughly 3000 rpm, that keeps it switched on; once load or coolant temperature drop back under this curve and the 85 C threshold, a countdown begins and the protection mode switches back off. Stock is a flat 0.650 grams per cylinder at every speed point from 1600 to 8000 rpm. Protection enrichment - DO NOT TUNE. Effect: protection enrichment Evidence: ledger:E0752, ledger:E1641</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1600" />
      <LABEL index="1" value="2400" />
      <LABEL index="2" value="3200" />
      <LABEL index="3" value="4000" />
      <LABEL index="4" value="4800" />
      <LABEL index="5" value="5600" />
      <LABEL index="6" value="6400" />
      <LABEL index="7" value="7200" />
      <LABEL index="8" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26D32" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/cyl (airmass)</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8.191875</max>
      <MATH equation="X/8000"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6E9" flags="0x30">
    <title>Commanded Mixture Lean Offset vs Temperature C (Inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Same commanded-mixture lean-offset mechanism as the other selectable variants of this table (a temperature-indexed amount subtracted from the commanded air-fuel mixture, floored so the mixture is never commanded leaner than a 1:1 equivalence ratio): this is variant C, selected instead of the others under a different vehicle condition. Its own calibration is entirely zero at every modelled-temperature point on this vehicle, so selecting it never actually changes the commanded mixture (inactive). 1x33 curve, -40 to 216 C in 8-degree steps. Effect: raise = more richness subtracted at that temperature (currently zero everywhere)...</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26E3E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ ratio offset</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6EA" flags="0x30">
    <title>Commanded Mixture Lean Offset vs Temperature D (Inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Same commanded-mixture lean-offset mechanism as the other selectable variants of this table (a temperature-indexed amount subtracted from the commanded air-fuel mixture, floored so the mixture is never commanded leaner than a 1:1 equivalence ratio): this is variant D, selected instead of the others under a different vehicle condition. Its own calibration is entirely zero at every modelled-temperature point on this vehicle, so selecting it never actually changes the commanded mixture (inactive). 1x33 curve, -40 to 216 C in 8-degree steps. Effect: raise = more richness subtracted at that temperature (currently zero everywhere)...</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26E86" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ ratio offset</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6EB" flags="0x30">
    <title>Open Loop Commanded Mixture Coolant Temperature Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the open loop commanded fuel mixture by this factor, by modelled coolant temperature, while the computer runs one of its open loop mixture correction modes (the operating condition that selects this mode is still unidentified). A value of 1.0 makes no change; above 1.0 richens the open loop mixture at that temperature, below 1.0 leans it. Stock is 1.0 at every temperature, so it has no effect on the stock truck in any mode. Effect: raise = richer open loop mixture at this coolant temperature while this correction mode is active, lower = leaner. Stock is 1.0 (no effect) across the whole range. Evidence: ledger:E0752...</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC (modelled temperature)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2708E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier (1.0 = no change)</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6EC" flags="0x30">
    <title>Open Loop Commanded Mixture Barometric Pressure Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the open loop commanded fuel mixture by this factor, by barometric pressure, while the computer runs one of its open loop mixture correction modes (the operating condition that selects this mode is still unidentified). A value of 1.0 makes no change. Values above 1.0 richen the open loop mixture at that pressure; values below 1.0 lean it out. Stock calibration holds this at 1.0 across the entire pressure range, so it currently has no effect on the truck. Effect: raise = richer open loop mixture at this barometric pressure while this correction mode is active, lower = leaner. Stock is 1.0 (no effect) across the whol...</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2700E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier (1.0 = no change)</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6ED" flags="0x30">
    <title>Open Loop Commanded Mixture System Voltage Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the open loop commanded fuel mixture by this factor, by system voltage, while the computer runs one of its open loop mixture correction modes (the operating condition that selects this mode is still unidentified). A value of 1.0 makes no change. Values above 1.0 richen the open loop mixture at that voltage; values below 1.0 lean it out. Stock calibration holds this at 1.0 across the entire voltage range, so it currently has no effect on the truck. Effect: raise = richer open loop mixture at this system voltage while this correction mode is active, lower = leaner. Stock is 1.0 (no effect) across the whole range. Evi...</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>V (system)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x27046" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier (1.0 = no change)</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6EE" flags="0x30">
    <title>O2 Heater Turn-On Delay vs Startup Coolant - Upstream Sensor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long after engine start the upstream O2 sensor heater stays off (apart from a brief measuring pulse each second), by coolant temperature at start-up. The delay protects a cold sensor from water in the exhaust. Stock 148 s at -16 C and below, 36 s at 8 C, 1 s from 20 C. Effect: lower = the heater comes on sooner after a cold start Evidence: ledger:E1019, ledger:E1020</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C680" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6EF" flags="0x30">
    <title>O2 Heater Turn-On Delay vs Startup Coolant - Downstream Sensor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long after engine start the downstream O2 sensor heater stays off (apart from a brief measuring pulse each second), by coolant temperature at start-up. The delay protects a cold sensor from water in the exhaust. Stock 208 s at -16 C and below, 45 s at 8 C, 15 s up to 44 C, 1 s from 56 C. Effect: lower = the heater comes on sooner after a cold start Evidence: ledger:E1019, ledger:E1020</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C6A4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x6F0" flags="0x0">
    <title>O2 Heater - Measuring Pulse Read Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor heater: once a second each heater is driven fully on for a short measuring pulse; this is how long the pulse has run before heater current and voltage are read. Stock 0.0375 s. Effect: raise = the reading is taken later in the pulse Evidence: ledger:E1062</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C998" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x6F1" flags="0x30">
    <title>O2 Heater - Temperature per Ohm vs Learned Offset, Upstream</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor heater, upstream sensor: how many degrees the heater temperature estimate rises per ohm of heater resistance above nominal, chosen by the resistance offset stored by the cold-start learn. Stock 125 degC per ohm at an offset of -1.2 ohm and below rising to 184 at +0.9 ohm and above. Change only for a different sensor. Effect: raise = the heater temperature estimate rises faster with resistance Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>ohm (learned offset)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-3" />
      <LABEL index="1" value="-2.85" />
      <LABEL index="2" value="-2.7" />
      <LABEL index="3" value="-2.55" />
      <LABEL index="4" value="-2.4" />
      <LABEL index="5" value="-2.25" />
      <LABEL index="6" value="-2.1" />
      <LABEL index="7" value="-1.95" />
      <LABEL index="8" value="-1.8" />
      <LABEL index="9" value="-1.65" />
      <LABEL index="10" value="-1.5" />
      <LABEL index="11" value="-1.35" />
      <LABEL index="12" value="-1.2" />
      <LABEL index="13" value="-1.05" />
      <LABEL index="14" value="-0.9" />
      <LABEL index="15" value="-0.75" />
      <LABEL index="16" value="-0.6" />
      <LABEL index="17" value="-0.45" />
      <LABEL index="18" value="-0.3" />
      <LABEL index="19" value="-0.15" />
      <LABEL index="20" value="0" />
      <LABEL index="21" value="0.15" />
      <LABEL index="22" value="0.3" />
      <LABEL index="23" value="0.45" />
      <LABEL index="24" value="0.6" />
      <LABEL index="25" value="0.75" />
      <LABEL index="26" value="0.9" />
      <LABEL index="27" value="1.05" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.35" />
      <LABEL index="30" value="1.5" />
      <LABEL index="31" value="1.65" />
      <LABEL index="32" value="1.8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C7E8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC per ohm</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6F2" flags="0x30">
    <title>O2 Heater - Upstream Duty vs Heater Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor heater: upstream heater duty by estimated heater temperature (the lower of this and the voltage limit is used). Stock 98 % up to 700 degC, 80 % at 750, 30 % at 800, off from 850 degC. Effect: raise = more heater power at that heater temperature Evidence: ledger:E1062</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (heater temperature)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="200" />
      <LABEL index="1" value="250" />
      <LABEL index="2" value="300" />
      <LABEL index="3" value="350" />
      <LABEL index="4" value="400" />
      <LABEL index="5" value="450" />
      <LABEL index="6" value="500" />
      <LABEL index="7" value="550" />
      <LABEL index="8" value="600" />
      <LABEL index="9" value="650" />
      <LABEL index="10" value="700" />
      <LABEL index="11" value="750" />
      <LABEL index="12" value="800" />
      <LABEL index="13" value="850" />
      <LABEL index="14" value="900" />
      <LABEL index="15" value="950" />
      <LABEL index="16" value="1000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C780" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6F3" flags="0x30">
    <title>O2 Heater - Upstream Duty Limit vs System Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor heater: highest upstream heater duty by system voltage. Stock 98 % up to 13 V falling to 60.5 % at 18 V. Effect: raise = more heater power allowed at that system voltage Evidence: ledger:E1062</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>V (system)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="8" />
      <LABEL index="1" value="9.25" />
      <LABEL index="2" value="10.5" />
      <LABEL index="3" value="11.75" />
      <LABEL index="4" value="13" />
      <LABEL index="5" value="14.25" />
      <LABEL index="6" value="15.5" />
      <LABEL index="7" value="16.75" />
      <LABEL index="8" value="18" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C7A4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x6F4" flags="0x0">
    <title>O2 Heater - Over-Temperature Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor heater: estimated heater temperature above which the downstream heater is switched off and the over-temperature flag is set for either sensor. Stock 825 degC. Effect: raise = the heater is allowed to run hotter Evidence: ledger:E1062</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C756" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6F5" flags="0x0">
    <title>O2 Heater - Downstream Switch-On Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor heater: estimated heater temperature below which the downstream heater is switched back on (at 98 % duty). Stock 800 degC. Effect: raise = the downstream heater is held at a higher temperature Evidence: ledger:E1062</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C758" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6F6" flags="0x0">
    <title>Idle Air Integral - Step Down RPM Margin</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air control: the airflow integral may remove air only when engine speed is at least this far above desired idle. Stock 50 rpm. Effect: raise = the integral removes air only at a larger idle overshoot Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2930E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6F7" flags="0x0">
    <title>Idle Predicted Airflow Floor - Speed Minimum With RPM Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: while the rpm airflow adder is in use, the predicted airflow floor applies only above this speed (as well as above the per gear speed gate). Stock 8 km/h. Effect: raise = the floor applies only at higher speed while the rpm adder is in use Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29310" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6F8" flags="0x0">
    <title>Idle Airflow Correction Term - Input Filter (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this belongs to an idle airflow correction term whose output curve is all zero, so the term adds nothing. The term is added to the idle airflow sum at road speed with the throttle closed, outside decel fuel cut, once the idle airflow error has settled. This value is the filter speed of the term&#x27;s input, per update. Stock 0.05. Effect: no effect on the stock calibration Evidence: ledger:E0754, ledger:E0897</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2930C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6F9" flags="0x0">
    <title>Idle Airflow Correction Term - Settled Error Threshold (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this belongs to an idle airflow correction term whose output curve is all zero, so the term adds nothing. The term is added to the idle airflow sum at road speed with the throttle closed, outside decel fuel cut, once the idle airflow error has settled. This value is the idle airflow error below which the term is allowed. Stock 1.0 g/s. Effect: no effect on the stock calibration Evidence: ledger:E0754, ledger:E0897</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2930A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x6FA" flags="0x30">
    <title>Idle Airflow Closed-Loop Step - Airflow Error Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: the 17 airflow error values (measured minus predicted airflow) at which the cells of the closed loop step table sit. Stock -4 to +6 g/s. Keep them rising from left to right. Effect: move a breakpoint = the step cell at that position acts at a different airflow error Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>cell of the step table</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29316" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x6FB" flags="0x0">
    <title>Idle Airflow Correction Term - Minimum Speed (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this belongs to an idle airflow correction term whose output curve is all zero, so the term adds nothing. The term is added to the idle airflow sum at road speed with the throttle closed, outside decel fuel cut, once the idle airflow error has settled. This value is the minimum vehicle speed for the term. Stock 18 km/h. Effect: no effect on the stock calibration Evidence: ledger:E0754, ledger:E0897</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29312" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6FC" flags="0x0">
    <title>Decel Fuel Cut Idle Air - First Target Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air during decel fuel cut: time the first target is held before the idle air moves to the second target. Stock 1 s. Effect: raise = the first target is held longer Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29F6C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x6FD" flags="0x30">
    <title>Idle Base Airflow - Coolant Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the base idle airflow (Idle Airflow - Base vs RPM) by engine coolant temperature, applied together with the baro factor. Stock 1.0 at every coolant temperature. Effect: raise = more base idle airflow at that coolant temperature Evidence: ledger:E0754, ledger:E1370</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2955E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6FE" flags="0x30">
    <title>Idle Closed Loop, Alternate Mode MAP Target Coolant Factor (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant-temperature scaling factor for the target used by an alternate idle closed-loop calculation mode. That alternate mode is never selected on this vehicle, so this factor has no effect here (inactive). Stock 1.20 at the coldest point on this bin, tapering to 1.00 by normal operating temperature. Effect: n/a (alternate mode not selected on this vehicle) Evidence: ledger:E0754</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (ECT)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29582" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x6FF" flags="0x0">
    <title>Decel Fuel Cut Idle Air - Rise Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air during decel fuel cut: step per 12.5 ms by which the idle air rises to its first target when fuel cut starts. Stock 32 g/s: it jumps to the target at once. Effect: lower = the idle air ramps in instead of jumping Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29E80" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x700" flags="0x0">
    <title>Decel Fuel Cut Idle Air - Step to Second Target</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air during decel fuel cut: step per 12.5 ms by which the idle air moves from the first target to the second target after the hold time. Stock 0.1 g/s (8 g/s per second). Effect: raise = the idle air reaches the second target sooner Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29E82" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x701" flags="0x30">
    <title>Decel Fuel Cut Idle Air - First Target vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air during decel fuel cut: idle air added right after fuel cut starts, by engine speed (0 to 4096 rpm). Stock 0 to 2.4 g/s. Effect: raise = more air through the throttle at the start of fuel cut Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29EAE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x702" flags="0x30">
    <title>Decel Fuel Cut Idle Air - Second Target vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air during decel fuel cut: idle air for the rest of the fuel cut, after the hold time, by engine speed (0 to 4096 rpm). Stock 0 to -2.07 g/s: air is taken away. Effect: raise (less negative) = more air through the throttle during fuel cut Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29ED2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x703" flags="0x30">
    <title>Idle Airflow - Coolant Term</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added by engine coolant temperature (stock 15.0 g/s at -40 C falling to 3.9 g/s from 92 C up). It is one of the terms summed into the predicted idle airflow that the idle controller opens the throttle for. Two rows: the PCM uses the second row when the idle calibration switch is on, which it is on this truck; the first row is the alternate. Each row keeps its own point count word. Effect: raise = more idle airflow (higher idle throttle opening) at that coolant temperature Evidence: ledger:E0287, ledger:E0754, ledger:E...</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alternate (switch off)" />
      <LABEL index="1" value="used (switch on, stock)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29CEE" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x704" flags="0x30">
    <title>Injector Short Pulse Width Correction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the commanded injector pulse width for a cylinder is below about 3.0 ms, this curve adds a correction onto it before it reaches the injector driver, compensating for injector nonlinearity at very short pulse widths. Above 3.0 ms the pulse width passes through unchanged. While the engine is running, the corrected result is never allowed below about 0.66 ms. Indexed by the uncorrected pulse width itself, 0 to 4.0 ms. Stock adds up to +0.17 ms at the shortest pulse widths, tapering to +0.016 ms by 4.0 ms. Effect: raise = more pulse width added back in at short injector pulse widths Evidence: ledger:E0755, ledger:E0936, ledg...</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>ms (pulse width)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.125" />
      <LABEL index="2" value="0.25" />
      <LABEL index="3" value="0.375" />
      <LABEL index="4" value="0.5" />
      <LABEL index="5" value="0.625" />
      <LABEL index="6" value="0.75" />
      <LABEL index="7" value="0.875" />
      <LABEL index="8" value="1" />
      <LABEL index="9" value="1.125" />
      <LABEL index="10" value="1.25" />
      <LABEL index="11" value="1.375" />
      <LABEL index="12" value="1.5" />
      <LABEL index="13" value="1.625" />
      <LABEL index="14" value="1.75" />
      <LABEL index="15" value="1.875" />
      <LABEL index="16" value="2" />
      <LABEL index="17" value="2.125" />
      <LABEL index="18" value="2.25" />
      <LABEL index="19" value="2.375" />
      <LABEL index="20" value="2.5" />
      <LABEL index="21" value="2.625" />
      <LABEL index="22" value="2.75" />
      <LABEL index="23" value="2.875" />
      <LABEL index="24" value="3" />
      <LABEL index="25" value="3.125" />
      <LABEL index="26" value="3.25" />
      <LABEL index="27" value="3.375" />
      <LABEL index="28" value="3.5" />
      <LABEL index="29" value="3.625" />
      <LABEL index="30" value="3.75" />
      <LABEL index="31" value="3.875" />
      <LABEL index="32" value="4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26056" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>ms (pulse width)</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x705" flags="0x0">
    <title>Injector Short Pulse Width Correction Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this commanded pulse width, the short-pulse-width correction curve is applied; at or above it the commanded pulse width passes through unchanged. Stock 3.0 ms. Effect: raise = correction applies over a wider range of pulse widths Evidence: ledger:E0755</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2604C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ms (pulse width)</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x706" flags="0x0">
    <title>Injector Short Pulse Width Correction Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While the engine is running, the corrected pulse width from the short-pulse-width correction is never allowed to fall below this value. Stock 0.656 ms. Effect: raise = corrected short pulse widths are floored higher Evidence: ledger:E0755</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26050" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ms (pulse width)</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x707" flags="0x0">
    <title>Injector Short Pulse Width Correction Ceiling Guard</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. An overflow guard on the corrected pulse width: values above this are clamped down to it. Stock 464.0 ms, far above any real commanded pulse width, so this guard is not reached in normal operation. Effect: raise = the (practically unreachable) overflow guard moves higher Evidence: ledger:E0755</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2604E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ms (pulse width)</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x708" flags="0x30">
    <title>Injector Offset - Correction vs Fuel Temperature (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the injector offset by modelled fuel temperature (coolant, or a hot-soak estimate after a hot restart), -30 to 130 C. Used only while its enable is set. Stock 0 at every temperature. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = more injector offset at that temperature) Evidence: ledger:E0755, ledger:E0936, ledger:E1162, ledger:E1270, ledger:E1278</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC (modelled fuel temperature)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-30" />
      <LABEL index="1" value="-25" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-15" />
      <LABEL index="4" value="-10" />
      <LABEL index="5" value="-5" />
      <LABEL index="6" value="0" />
      <LABEL index="7" value="5" />
      <LABEL index="8" value="10" />
      <LABEL index="9" value="15" />
      <LABEL index="10" value="20" />
      <LABEL index="11" value="25" />
      <LABEL index="12" value="30" />
      <LABEL index="13" value="35" />
      <LABEL index="14" value="40" />
      <LABEL index="15" value="45" />
      <LABEL index="16" value="50" />
      <LABEL index="17" value="55" />
      <LABEL index="18" value="60" />
      <LABEL index="19" value="65" />
      <LABEL index="20" value="70" />
      <LABEL index="21" value="75" />
      <LABEL index="22" value="80" />
      <LABEL index="23" value="85" />
      <LABEL index="24" value="90" />
      <LABEL index="25" value="95" />
      <LABEL index="26" value="100" />
      <LABEL index="27" value="105" />
      <LABEL index="28" value="110" />
      <LABEL index="29" value="115" />
      <LABEL index="30" value="120" />
      <LABEL index="31" value="125" />
      <LABEL index="32" value="130" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26604" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>ms</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x709" flags="0x30">
    <title>Transient Fuel Evaporation RPM Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A Q15 multiplicative gain (32768 raw = 1.0, no correction), indexed by engine speed, on the evaporation fraction of the port-wall wetting (wall-film / puddle) fuel model: the fraction of the fuel puddle on the intake port wall that evaporates back into the airstream each update. Feeds directly into the model&#x27;s evaporation-fraction coefficient alongside a MAP x temperature table, through the standard Q15 shift-15 helper. Stock is a uniform 1.0 (no correction) from 0 to 6400 rpm. Effect: raise = more of the fuel puddle evaporates back into the airstream at that engine speed Evidence: ledger:E0755</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26A38" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw (Q15, 32768 = 1.0)</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x70A" flags="0x30">
    <title>Closed Loop O2 Filter Gain - Error Signal</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): filter on the O2 voltage that is used to work out how far the signal is past the switch point (the input of the step interval and proportional factors), by airflow. Share of each new reading taken every 12.5 ms. Stock 0.005 at idle rising to 0.1. Effect: raise = that signal follows the O2 sensor faster Evidence: ledger:E1126</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s used airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4.8" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="13.2" />
      <LABEL index="4" value="21.8" />
      <LABEL index="5" value="29.5" />
      <LABEL index="6" value="40.3" />
      <LABEL index="7" value="51.8" />
      <LABEL index="8" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x259A0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x70B" flags="0x30">
    <title>Closed Loop O2 Filter Gain - Purge Feedback Signal</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Front O2: filter on the O2 voltage that the canister purge feedback reads, by airflow. Share of each new reading taken every 12.5 ms. Stock 0.005 at idle rising to 0.14. Effect: raise = that signal follows the O2 sensor faster Evidence: ledger:E1126</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s used airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4.8" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="13.2" />
      <LABEL index="4" value="21.8" />
      <LABEL index="5" value="29.5" />
      <LABEL index="6" value="40.3" />
      <LABEL index="7" value="51.8" />
      <LABEL index="8" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x259C8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x70C" flags="0x0">
    <title>EVAP Fuel Vapor Temperature - Default When Sensor Faulted</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP fuel vapour temperature sensor: vapour temperature used while the sensor circuit is faulted. Stock 20 C. Effect: sets the substitute vapour temperature Evidence: ledger:E0756, ledger:E1482</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x35F80" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x70D" flags="0x30">
    <title>EVAP Fuel Vapor Temperature vs Sensor Resistance</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP fuel vapour temperature sensor: converts the sensor resistance into the fuel vapour temperature. The resistance axis is logarithmic, 4 to 2048 ohm in 33 points (nine doublings). Stock 88.3 C at 4 ohm down to -19.5 C at 2048 ohm. Effect: changes the reported vapour temperature for a given sensor resistance Evidence: ledger:E0756, ledger:E0937, ledger:E1482</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>ohm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="4.0" />
      <LABEL index="1" value="4.9" />
      <LABEL index="2" value="5.9" />
      <LABEL index="3" value="7.2" />
      <LABEL index="4" value="8.7" />
      <LABEL index="5" value="10.6" />
      <LABEL index="6" value="12.9" />
      <LABEL index="7" value="15.7" />
      <LABEL index="8" value="19.0" />
      <LABEL index="9" value="23.1" />
      <LABEL index="10" value="28.1" />
      <LABEL index="11" value="34.1" />
      <LABEL index="12" value="41.5" />
      <LABEL index="13" value="50.4" />
      <LABEL index="14" value="61.3" />
      <LABEL index="15" value="74.5" />
      <LABEL index="16" value="90.5" />
      <LABEL index="17" value="110.0" />
      <LABEL index="18" value="133.7" />
      <LABEL index="19" value="162.4" />
      <LABEL index="20" value="197.4" />
      <LABEL index="21" value="239.9" />
      <LABEL index="22" value="291.5" />
      <LABEL index="23" value="354.3" />
      <LABEL index="24" value="430.5" />
      <LABEL index="25" value="523.2" />
      <LABEL index="26" value="635.8" />
      <LABEL index="27" value="772.7" />
      <LABEL index="28" value="939.0" />
      <LABEL index="29" value="1141.1" />
      <LABEL index="30" value="1386.8" />
      <LABEL index="31" value="1685.3" />
      <LABEL index="32" value="2048.0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35F8A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x70E" flags="0x30">
    <title>A/C Clutch - Engage Delay vs Intake Air Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time from an A/C engage request to the compressor clutch being switched on, by intake air temperature. The extra A/C idle airflow is added during this delay, so the idle is ready before the compressor load arrives. Stock 0.25 s, 0.30 s at 79 C, 0.35 s from 84 C. Effect: raise = longer wait before the A/C compressor engages Evidence: ledger:E0756, ledger:E1865</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5.625" />
      <LABEL index="2" value="11.25" />
      <LABEL index="3" value="16.875" />
      <LABEL index="4" value="22.5" />
      <LABEL index="5" value="28.125" />
      <LABEL index="6" value="33.75" />
      <LABEL index="7" value="39.375" />
      <LABEL index="8" value="45" />
      <LABEL index="9" value="50.625" />
      <LABEL index="10" value="56.25" />
      <LABEL index="11" value="61.875" />
      <LABEL index="12" value="67.5" />
      <LABEL index="13" value="73.125" />
      <LABEL index="14" value="78.75" />
      <LABEL index="15" value="84.375" />
      <LABEL index="16" value="90" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28FCC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x70F" flags="0x30">
    <title>A/C Clutch - Disengage Delay vs Intake Air Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time from an A/C disengage request to the compressor clutch being switched off, by intake air temperature. Stock 0.6 s at every temperature. Effect: raise = the A/C compressor stays engaged longer after it is asked to switch off Evidence: ledger:E0756, ledger:E1865</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5.625" />
      <LABEL index="2" value="11.25" />
      <LABEL index="3" value="16.875" />
      <LABEL index="4" value="22.5" />
      <LABEL index="5" value="28.125" />
      <LABEL index="6" value="33.75" />
      <LABEL index="7" value="39.375" />
      <LABEL index="8" value="45" />
      <LABEL index="9" value="50.625" />
      <LABEL index="10" value="56.25" />
      <LABEL index="11" value="61.875" />
      <LABEL index="12" value="67.5" />
      <LABEL index="13" value="73.125" />
      <LABEL index="14" value="78.75" />
      <LABEL index="15" value="84.375" />
      <LABEL index="16" value="90" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28FF0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x710" flags="0x30">
    <title>EVAP Test Tank Vacuum Jump Limit B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Change in filtered tank vacuum between updates, by fuel level (0 to 100 %), that sets the second tank vacuum jump flag when the main flag is clear. Stock 32 inH2O in every cell, which is never reached. Effect: lower = a smaller tank vacuum jump sets the second flag Evidence: ledger:E0756, ledger:E0899, ledger:E0940, ledger:E0944, ledger:E1054</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35EB4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>inH2O</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x711" flags="0x30">
    <title>EVAP Test Tank Vacuum Jump Limit A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Change in filtered tank vacuum between updates, by fuel level (0 to 100 %), that sets the main tank vacuum jump flag, which pauses the leak test integration and restarts its count. Stock 32 inH2O in every cell, which is never reached. Effect: lower = a smaller tank vacuum jump pauses the leak test Evidence: ledger:E0756, ledger:E0899, ledger:E0940, ledger:E0944, ledger:E1054</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35E90" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>inH2O</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x712" flags="0x30">
    <title>Transmission Throttle vs Throttle Area Request</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converts the throttle-area request above idle (from the pedal, or from cruise control) into the throttle value the transmission&#x27;s shift, TCC and WOT schedules are looked up with. Stock rises steeply at first (3 % request gives 17 %, 25 % gives 49 %) and reaches 100 % at about 97 %. Effect: raise = the transmission schedules see more throttle for the same request Evidence: ledger:E0756, ledger:E0964</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>% throttle area request above idle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="3.125" />
      <LABEL index="2" value="6.25" />
      <LABEL index="3" value="9.375" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="15.625" />
      <LABEL index="6" value="18.75" />
      <LABEL index="7" value="21.875" />
      <LABEL index="8" value="25" />
      <LABEL index="9" value="28.125" />
      <LABEL index="10" value="31.25" />
      <LABEL index="11" value="34.375" />
      <LABEL index="12" value="37.5" />
      <LABEL index="13" value="40.625" />
      <LABEL index="14" value="43.75" />
      <LABEL index="15" value="46.875" />
      <LABEL index="16" value="50" />
      <LABEL index="17" value="53.125" />
      <LABEL index="18" value="56.25" />
      <LABEL index="19" value="59.375" />
      <LABEL index="20" value="62.5" />
      <LABEL index="21" value="65.625" />
      <LABEL index="22" value="68.75" />
      <LABEL index="23" value="71.875" />
      <LABEL index="24" value="75" />
      <LABEL index="25" value="78.125" />
      <LABEL index="26" value="81.25" />
      <LABEL index="27" value="84.375" />
      <LABEL index="28" value="87.5" />
      <LABEL index="29" value="90.625" />
      <LABEL index="30" value="93.75" />
      <LABEL index="31" value="96.875" />
      <LABEL index="32" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x319F8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (transmission throttle)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x713" flags="0x30">
    <title>Traction Control - Spark Retard Share vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control: factor on the part of a torque reduction that is handed to spark retard, by coolant temperature. Stock 0.1 cold rising to 1.0 hot: a cold engine gets little spark retard from traction control. Effect: raise = more of the traction control torque reduction is done with spark retard at that temperature Evidence: ledger:E1130</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x313D2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x714" flags="0x0">
    <title>A/C Cut at Idle Droop - Engine Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The A/C compressor is cut when engine speed falls below this while the idle droop catch is active (engine speed well below desired idle, see Idle Airflow vs RPM Below Desired). Stock 450 rpm. Effect: raise = the compressor is cut earlier in an idle speed dip; lower = later Evidence: ledger:E0756, ledger:E1566</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x28FBA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x715" flags="0x0">
    <title>A/C Cut at Idle Droop - Cut Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the A/C compressor stays cut after an idle droop cut starts (A/C Cut at Idle Droop - Engine Speed Limit). Stock 5.0 s. Effect: raise = the compressor stays off longer after an idle speed dip Evidence: ledger:E0756, ledger:E1566</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x28FBC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x716" flags="0x0">
    <title>A/C Disable - System Voltage Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C compressor is cut when system voltage falls below this. Stock 9.5 V. Effect: raise = the compressor is cut at a higher voltage Evidence: ledger:E1007</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x2088A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x717" flags="0x0">
    <title>A/C Re-Enable - System Voltage Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a low voltage cut, the A/C compressor is allowed again once system voltage rises above this. Stock 10.0 V. Effect: raise = the compressor stays cut until voltage recovers further Evidence: ledger:E1007</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x2088C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x718" flags="0x0">
    <title>A/C Disable - System Voltage High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C compressor is cut when system voltage rises above this. Stock 16.0 V. Effect: lower = the compressor is cut at a lower voltage Evidence: ledger:E1007</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x2088E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x719" flags="0x0">
    <title>A/C Engage While Cranking - Minimum Refrigerant Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The A/C compressor is engaged during engine cranking only when refrigerant pressure is at or above this (with the other cranking conditions met). Stock 150 kPa. Effect: raise = the compressor engages during cranking less often Evidence: ledger:E0756, ledger:E1568</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x20892" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x71A" flags="0x0">
    <title>A/C Engage While Cranking - Minimum System Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. System voltage must be at or above this for the A/C compressor to engage during cranking. Stock 8.5 V. Effect: raise = no compressor engagement on a weaker cranking voltage Evidence: ledger:E0756, ledger:E1568</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x20894" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x71B" flags="0x0">
    <title>A/C Engage While Cranking - Coolant Temperature Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The A/C compressor engages during cranking only while coolant temperature is below this. Stock 80 C. Effect: raise = cranking engagement also on a warmer engine; lower = only on a cooler engine Evidence: ledger:E0756, ledger:E1568</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x20896" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x71C" flags="0x0">
    <title>A/C Engage While Cranking - Minimum Intake Air Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intake air temperature must be above this for the A/C compressor to engage during cranking. Stock 5 C. Effect: raise = no cranking engagement in cooler weather Evidence: ledger:E0298, ledger:E0756, ledger:E0815, ledger:E1568</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x20898" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x71D" flags="0x0">
    <title>A/C Engage While Cranking - Maximum Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Longest time the A/C compressor stays engaged during one cranking event. It also ends as soon as the engine is running. Stock 3.5 s. Effect: raise = the compressor can stay engaged longer during a long crank Evidence: ledger:E0756, ledger:E1568</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x2089E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x71E" flags="0x0">
    <title>A/C Disable - Refrigerant Pressure High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C compressor is cut when refrigerant pressure rises above this. Stock 3160 kPa (458 psi). Effect: lower = the compressor is cut at a lower pressure Evidence: ledger:E1008</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x208A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x71F" flags="0x0">
    <title>EVAP Test - Pull-Down Vacuum Target</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak test (P0455): tank vacuum the purge controller aims for while it pulls the sealed system down. Stock 9.5 inH2O. Effect: raise = the test pulls the tank to a deeper vacuum Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3588A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x720" flags="0x0">
    <title>EVAP Test - Pull-Down Purge Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak test (P0455): least commanded purge during the pull-down. Stock 6 %. Effect: raise = purge never drops as low during the pull-down Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3588C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x721" flags="0x0">
    <title>EVAP Test - Pull-Down Over-Vacuum Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak test (P0455): time above the pull-down vacuum maximum before purge is shut. Stock 0.8 s. Effect: raise = purge is shut later on over-vacuum Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3588E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x722" flags="0x0">
    <title>EVAP Test - Pull-Down Vacuum Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak test (P0455): tank vacuum above which, after the over-vacuum time, purge is shut until vacuum falls back below the target. Stock 12 inH2O. Effect: raise = more vacuum is allowed before purge is shut Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3587E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x723" flags="0x0">
    <title>Knock Detection - Transient Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: how long the transient state is kept after the last transient trigger (engine speed, throttle or airmass). Used in steps of 12.5 ms. Stock 0.25 s. Effect: raise = knock detection stays in its transient settings for longer after a transient Evidence: ledger:E1138</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31D02" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>32.767500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x724" flags="0x0">
    <title>P2026 Test Enable - Coolant Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel vapor temperature sensor circuit low test (P2026) runs only while coolant is below this. Stock -30 C. P2026 is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0756, ledger:E1186</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F6E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC (ECT)</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x725" flags="0x0">
    <title>P2026 Test Enable - Minimum Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel vapor temperature sensor circuit low test (P2026) runs only after the engine has run longer than this. Stock 10 s. P2026 is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0756, ledger:E0811, ledger:E1186</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F70" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x726" flags="0x0">
    <title>P2026 Test Enable - Intake Air Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel vapor temperature sensor circuit low test (P2026) runs only while intake air temperature is at or below this. Stock 50 C. P2026 is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0756, ledger:E1186</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F72" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC (IAT)</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x727" flags="0x0">
    <title>P2026 Test Enable - Minimum Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel vapor temperature sensor circuit low test (P2026) runs only at or above this vehicle speed. Stock 25 km/h. P2026 is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0756, ledger:E1186</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F74" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x728" flags="0x30">
    <title>Idle Throttle Area - Air Temperature Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Physical term of the idle throttle area calculation: square root of (287 x intake air temperature in kelvin), by intake air temperature (-40 to 152 C). Stock 259 to 349. It is the gas law, not a tuning value, and two other routines share it: leave it as it is. Effect: raise = more throttle area for the same idle airflow at that air temperature Evidence: ledger:E1106</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC intake air</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2965C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>m/s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x729" flags="0x30">
    <title>Idle Throttle Area - Flow Function vs Pressure Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Physical term of the idle throttle area calculation: the nozzle flow function, by manifold pressure divided by barometric pressure (0 to 1). Stock 0.685 up to a ratio of 0.5 (sonic flow), falling to 0.465 at 0.875 and held there. It is physics, not a tuning value, and another routine shares it. Effect: lower = more throttle area for the same idle airflow at that pressure ratio Evidence: ledger:E1106</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>MAP / baro</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.062" />
      <LABEL index="2" value="0.125" />
      <LABEL index="3" value="0.188" />
      <LABEL index="4" value="0.25" />
      <LABEL index="5" value="0.312" />
      <LABEL index="6" value="0.375" />
      <LABEL index="7" value="0.438" />
      <LABEL index="8" value="0.5" />
      <LABEL index="9" value="0.562" />
      <LABEL index="10" value="0.625" />
      <LABEL index="11" value="0.688" />
      <LABEL index="12" value="0.75" />
      <LABEL index="13" value="0.812" />
      <LABEL index="14" value="0.875" />
      <LABEL index="15" value="0.938" />
      <LABEL index="16" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29680" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x72A" flags="0x30">
    <title>Cold Start High Idle - Minimum Time vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold start high idle: shortest time the high idle stays on, by coolant temperature at start (-40 to 152 C). After it the high idle ends once the truck moves faster than the request hold speed; it also ends when coolant reaches the end temperature. Stock 1800 / 1200 / 600 s at -40 / -28 / -16 C and 0 from -4 C. Effect: raise = the cold start high idle lasts longer Evidence: ledger:E1112</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC startup coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A5F6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x72B" flags="0x30">
    <title>Idle Airflow RPM Adder - Time After Power Enrichment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: how long after power enrichment ends the rpm airflow adder stays switched in, by engine speed (rows, 0 to 4096 rpm) and by how long the enrichment lasted (columns, 16 / 144 / 272 s). Stock 0 to 12 s. Effect: raise = the rpm adder stays in longer after coming off power Evidence: ledger:E1105, ledger:E1329</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>s power enrichment lasted</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="16" />
      <LABEL index="1" value="144" />
      <LABEL index="2" value="272" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1024" />
      <LABEL index="2" value="2048" />
      <LABEL index="3" value="3072" />
      <LABEL index="4" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x295A8" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x72C" flags="0x30">
    <title>Idle Predicted Airflow Floor - Speed Minimum by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: the predicted airflow floor (see the floor curve by rpm) applies only above this vehicle speed, one value per transmission state. Stock 200 km/h in every state, so the floor never applies. Effect: lower = the floor applies above that speed in that gear Evidence: ledger:E1110</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>transmission state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="not used" />
      <LABEL index="5" value="not used" />
      <LABEL index="6" value="Neutral" />
      <LABEL index="7" value="Reverse" />
      <LABEL index="8" value="Park" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x292F2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x72D" flags="0x30">
    <title>Idle Predicted Airflow - Floor vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: lowest value of the predicted idle airflow, by engine speed (400 to 3600 rpm). It applies only above the per gear speed gate, which stock sets to 200 km/h in every gear, so on stock this floor never applies. Effect: raise = higher minimum predicted airflow (only once the speed gate is lowered) Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x293B8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x72E" flags="0x0">
    <title>Idle Altitude Up - Coolant Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The altitude idle-up applies only while engine coolant is below this. Stock -256 C: never. Altitude idle-up: at low barometric pressure (below Idle Altitude Up Baro) with coolant below the limit, desired idle is raised by the altitude adder. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0757, ledger:E1508</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A598" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x72F" flags="0x0">
    <title>Cold Start High Idle - End Coolant Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold start high idle: the high idle ends when coolant reaches this. Stock 68 C. Effect: lower = the cold start high idle ends sooner Evidence: ledger:E1112</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A59A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x730" flags="0x0">
    <title>Cold Start High Idle - Arming Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold start high idle: it is armed at start only when startup coolant and intake air temperature are both at or below this. Stock -8 C. Effect: raise = the cold start high idle is also used on milder starts Evidence: ledger:E1112</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A59C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x731" flags="0x0">
    <title>Limp Mode 4th Gear Lockout - Hot Fluid Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission fault reaction. When fluid temperature rises above this value, 4th gear is replaced by 3rd whenever a major transmission fault code is stored (output speed sensor, shift solenoid A or B, converter clutch, shift timing solenoid, slipping). While the fluid is cooler (below the Clear value after being hot), the lockout follows only a stored shift solenoid B stuck-on code (P0757). Codes stay stored until cleared with a scan tool or aged out by the PCM. Stock 110 C. This reaction also runs while the transmission range switch reading is invalid (no valid range for the confirm time). Effect: raise = with a stored major...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x390F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x732" flags="0x0">
    <title>Limp Mode 4th Gear Lockout - Hot Fluid Clear Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fluid temperature below which the limp-mode 4th gear lockout switches back from the hot-fluid rule (any major transmission fault code) to the cool rule (shift solenoid B stuck-on only). Stock 100 C. This reaction also runs while the transmission range switch reading is invalid (no valid range for the confirm time). Effect: lower = the hot-fluid rule stays in force until the fluid cools further Evidence: ledger:E0758, ledger:E0765, ledger:E0770, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x390F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x733" flags="0x0">
    <title>Limp Mode 3rd Gear Hold - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission fault reaction. On (stock): with a shift solenoid A code stored (P0752, P0973, P0974) and the truck already in 3rd or 4th above the Minimum Speed, a command for 1st or 2nd is changed to 3rd. Codes stay stored until cleared with a scan tool or aged out by the PCM. This reaction also runs while the transmission range switch reading is invalid (no valid range for the confirm time). Effect: off = no 3rd gear hold with a shift solenoid A fault Evidence: ledger:E0758, ledger:E0765, ledger:E0770, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39104" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x734" flags="0x0">
    <title>Limp Mode 3rd Gear Hold - Minimum Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission-side road speed above which the limp-mode 3rd gear hold (shift solenoid A codes) acts. Stock 35 km/h (21.7 mph). This reaction also runs while the transmission range switch reading is invalid (no valid range for the confirm time). Effect: raise = the hold only acts at higher speed, so downshifts into 1st / 2nd are allowed up to it Evidence: ledger:E0758, ledger:E0765, ledger:E0770, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39106" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x735" flags="0x0">
    <title>Limp Mode Forced 4th - Minimum Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission fault reaction. With an output speed sensor high code or a shift solenoid B code stored (P0503, P0756, P0976, P0977), a 3rd gear command becomes 4th at or above this transmission-side road speed. Stock 200 km/h, so it does not act in practice. This reaction also runs while the transmission range switch reading is invalid (no valid range for the confirm time). Effect: lower = with those codes stored, 3rd is forced to 4th from a lower speed Evidence: ledger:E0758, ledger:E0765, ledger:E0770, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x390F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x736" flags="0x0">
    <title>Burst Knock Retard - Startup Decay Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During the first seconds after start (the startup decay window), the burst knock retard is multiplied by this every update. Stock 0.5, so it halves each update. Effect: raise = burst knock retard fades more slowly after start Evidence: ledger:E0759</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AF1A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x737" flags="0x0">
    <title>Burst Knock Retard - Startup Decay Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Run time after start during which the burst knock retard is scaled down every update by the startup decay factor. Stock 15 s. Effect: raise = the startup decay lasts longer Evidence: ledger:E0759</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AF1C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x738" flags="0x0">
    <title>P0136 Test - Fuel Step Attempt Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0136: the test may force rich and lean fuel steps to make the downstream sensor swing. Once the number of step attempts plus aborted steps reaches this, no more steps are forced. Stock 50. Effect: lower = fewer forced fuel steps are allowed Evidence: ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x374DC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x739" flags="0x0">
    <title>P0136 Test Enable - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): the forced fuel steps only start while engine speed is at or above this. Stock 1000 rpm. Effect: raise = a step needs a higher rpm Evidence: ledger:E0760, ledger:E0805, ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x374DE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x73A" flags="0x0">
    <title>P0136 Test Enable - RPM Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): the forced fuel steps only start while engine speed is at or below this. Stock 5000 rpm. Effect: lower = no step at high rpm Evidence: ledger:E0760, ledger:E0805, ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x374E0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x73B" flags="0x0">
    <title>P0136 Test Enable - Airflow Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): the forced fuel steps only start while mass airflow is at or above this. Stock 10 g/s. Effect: raise = a step needs more airflow Evidence: ledger:E0760, ledger:E0805, ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x374E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s (MAF)</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x73C" flags="0x0">
    <title>P0136 Test Enable - Airflow Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): the forced fuel steps only start while mass airflow is at or below this. Stock 100 g/s. Effect: lower = no step at high airflow Evidence: ledger:E0760, ledger:E0805, ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x374E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s (MAF)</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x73D" flags="0x0">
    <title>P0136 Test Enable - Vehicle Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): the forced fuel steps only start while vehicle speed is at or above this. Stock 30 km/h. Effect: raise = a step needs a higher road speed Evidence: ledger:E0760, ledger:E0805, ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x374E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x73E" flags="0x0">
    <title>P0136 Test Enable - Vehicle Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): the forced fuel steps only start while vehicle speed is at or below this. Stock 130 km/h. Effect: lower = no step at high road speed Evidence: ledger:E0760, ledger:E0805, ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x374E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x73F" flags="0x0">
    <title>P0136 Test Enable - Stable Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): its engine speed, airflow and vehicle speed windows must hold for this long before a forced fuel step starts. Stock 1.0 s. Effect: raise = conditions must hold longer before a fuel step Evidence: ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x374EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x740" flags="0x0">
    <title>P0136 Test - Lean Step Commanded EQ</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): commanded EQ ratio during the forced lean fuel step. Stock 0.90. Effect: lower = a leaner step Evidence: ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x374F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x741" flags="0x0">
    <title>P0136 Test - Rich Step Commanded EQ</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downstream O2 sensor test (P0136): commanded EQ ratio during the forced rich fuel step. Stock 1.10. Effect: raise = a richer step Evidence: ledger:E1003</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x374F8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x742" flags="0x0">
    <title>O2 Response Test Enable - Airflow Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor response test (P0133 / P1133 / P1134) only samples while mass airflow is at or above this. Stock 15 g/s. Effect: raise = the test needs more airflow to run Evidence: ledger:E0993</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34792" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x743" flags="0x0">
    <title>O2 Response Test Enable - Airflow Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor response test (P0133 / P1133 / P1134) only samples while mass airflow is at or below this. Stock 50 g/s. Effect: raise = the test also runs at higher airflow Evidence: ledger:E0993</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34794" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x744" flags="0x0">
    <title>O2 Response Test Enable - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor response test (P0133 / P1133 / P1134) only samples while engine speed is at or above this. Stock 1000 rpm. Effect: raise = the test needs a higher rpm to run Evidence: ledger:E0993</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34798" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x745" flags="0x0">
    <title>O2 Response Test Enable - RPM Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor response test (P0133 / P1133 / P1134) only samples while engine speed is at or below this. Stock 3500 rpm. Effect: raise = the test also runs at higher rpm Evidence: ledger:E0993</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3479A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x746" flags="0x0">
    <title>O2 Response Test Enable - Throttle Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor response test (P0133 / P1133 / P1134) only samples while throttle position, with the share used for idle air taken out, is at or above this. Stock 5 %. Effect: raise = the test needs more throttle to run Evidence: ledger:E0993</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3479E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x747" flags="0x0">
    <title>O2 Response Test Enable - Purge Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor response test (P0133 / P1133 / P1134) only runs while commanded evap purge is at or above this. Stock 0 %, so purge never blocks it. Effect: raise = the test waits for purge to be flowing Evidence: ledger:E0993</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x748" flags="0x0">
    <title>O2 Sensor Tests Enable - Fuel Level Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor response test and the O2 sensor voltage checks (P0131 / P0132 / P0137 / P0138) only run with fuel level at or above this, unless a fuel level sensor code (P0461 / P0462 / P0463) is active. Stock 10 %. Effect: lower = the tests also run with less fuel in the tank Evidence: ledger:E0993</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x749" flags="0x0">
    <title>O2 Response Test Enable - Coolant Temp Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor response test (P0133 / P1133 / P1134) only runs with coolant temperature above this. Stock 70 C. Effect: lower = the test can run on a cooler engine Evidence: ledger:E0993</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x74A" flags="0x0">
    <title>O2 Sensor Tests Enable - System Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor tests (response test, sensor voltage checks P0131 / P0132 / P0137 / P0138 and the downstream sensor test P0136) only run with system voltage at or below this. Stock 18.0 V. Effect: lower = the tests stop at a lower voltage Evidence: ledger:E0993</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x74B" flags="0x0">
    <title>O2 Sensor Tests Enable - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor tests (response test, sensor voltage checks P0131 / P0132 / P0137 / P0138 and the downstream sensor test P0136) only run with system voltage at or above this. Stock 11.0 V. Effect: raise = the tests need a higher voltage to run Evidence: ledger:E0993</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x74C" flags="0x0">
    <title>O2 Response Test - Start Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor response test (P0133 / P1133 / P1134) starts sampling once its run conditions have held for this long. Stock 2.0 s. Effect: raise = conditions must hold longer before sampling starts Evidence: ledger:E0993</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x74D" flags="0x0">
    <title>O2 Response Test - Sampling Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor response test (P0133 / P1133 / P1134) is judged once it has sampled for this long in total. Stock 120 s. Effect: lower = the test finishes on less data Evidence: ledger:E0993</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x74E" flags="0x0">
    <title>O2 Response Test Enable - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor response test (P0133 / P1133 / P1134) only runs after the engine has been running longer than this. Stock 200 s. Effect: lower = the test can start sooner after a start Evidence: ledger:E0993</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x74F" flags="0x0">
    <title>O2 Sensor Tests Enable - Voltage Out Of Range Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. System voltage must stay outside the voltage window of the O2 sensor tests for this long before the response test and the sensor voltage checks are stopped. Stock 3 s. Effect: raise = short voltage dips or spikes are ignored for longer Evidence: ledger:E0993</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347B8" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x750" flags="0x0">
    <title>O2 Lean In Power Enrichment Check - Other Sensor Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor lean in power enrichment check (sets P0131 upstream, P0137 downstream): a sample is only taken while the other O2 sensor reads at least this, which confirms the mixture really is rich. Stock 700 mV. Effect: lower = samples are taken with a weaker rich reading on the other sensor Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34BC0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x751" flags="0x0">
    <title>P0140 Early Pass - Active Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor activity check, early pass for the downstream sensor (P0140): the check passes once this many samples have read outside the early pass voltage band. Stock 60. Effect: raise = more active samples are needed for the early pass Evidence: ledger:E0995</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34BC2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x752" flags="0x0">
    <title>P0140 Early Pass - Voltage Band Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor activity check, early pass for the downstream sensor (P0140): a sample is inactive while the sensor reads above this and below the band high limit. Stock 300 mV. Effect: raise = lower readings count as active Evidence: ledger:E0995</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34BC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x753" flags="0x0">
    <title>P0140 Early Pass - Voltage Band High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor activity check, early pass for the downstream sensor (P0140): a sample is inactive while the sensor reads below this and above the band low limit. Stock 600 mV. Effect: lower = higher readings count as active Evidence: ledger:E0995</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34BC6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x754" flags="0x30">
    <title>P0134 / P0140 Check - Inactive Voltage Band Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor activity check (P0134 upstream, P0140 downstream): a sample counts as inactive when the sensor reads above this and below the band high limit. Stock 400 mV upstream, 425 mV downstream. The array has room for four O2 sensors; this engine has two, so the third and fourth values are never used. Effect: raise = the inactive band gets narrower Evidence: ledger:E0995, ledger:E1561</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <LABEL index="2" value="sensor 3 (not fitted, unused)" />
      <LABEL index="3" value="sensor 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34BC8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x755" flags="0x0">
    <title>Secondary Air Run - Start-Up Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Secondary air: the run time is only set up when the coolant temperature at start-up is above this. Stock 140 C. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (raise = secondary air needs a warmer start) Evidence: ledger:E0760, ledger:E0921, ledger:E1260</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA0A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x756" flags="0x0">
    <title>O2 Heater Cold Learn - Engine Run Time Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater cold-start resistance learn (after a long soak the PCM measures each heater cold and stores how far its resistance is from nominal): only accepted while engine run time is below this, so it has to happen in the first measuring pulse after start. Stock 1.15 s. Effect: raise = a later first pulse still counts as cold Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C99A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x757" flags="0x0">
    <title>O2 Heater Cold Learn - Coolant to Intake Air Difference Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater cold-start resistance learn (after a long soak the PCM measures each heater cold and stores how far its resistance is from nominal): only runs (and only stores its result) while coolant and intake air temperature differ by less than this. Stock 140 degC, which never limits. Effect: lower = the learn needs coolant and intake air to agree more closely Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C99C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x758" flags="0x0">
    <title>O2 Heater - Reference Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor heater: temperature at which the nominal heater resistance applies; the learn compares coolant temperature with it and the heater temperature estimate starts from it. Stock 20 degC. Change only with the nominal resistance. Effect: changes the predicted cold resistance and the heater temperature estimate together Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C99E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x759" flags="0x0">
    <title>O2 Heater Cold Learn - Coolant Temperature Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater cold-start resistance learn (after a long soak the PCM measures each heater cold and stores how far its resistance is from nominal): only runs with coolant temperature below this. Stock 45 degC. Effect: raise = the learn also runs on a warmer engine Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C9A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x75A" flags="0x0">
    <title>O2 Heater Cold Learn - Coolant Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater cold-start resistance learn (after a long soak the PCM measures each heater cold and stores how far its resistance is from nominal): only runs with coolant temperature above this. Stock -30 degC. Effect: lower = the learn also runs on a colder engine Evidence: ledger:E1063</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2C9A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x75B" flags="0x0">
    <title>Trans Fluid Temp Substitute - Use Estimate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the fluid temperature sensor is faulted, the PCM replaces the fluid temperature with a substitute. On (stock): the substitute is estimated from engine coolant temperature and run time (the items below). Off: the fixed Substitute Value is used instead. The substitute is also used while the transmission range switch reading is invalid; with the estimate on it is then the Invalid Range Switch Value (stock 141 C). Effect: off = a fixed substitute fluid temperature is used during a sensor fault Evidence: ledger:E0761, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DED2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x75C" flags="0x0">
    <title>Trans Fluid Temp Substitute - Fixed Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fluid temperature assumed during a fluid temperature sensor fault when the estimate is turned off. Stock 140 C (not used with the stock estimate on). The substitute is also used while the transmission range switch reading is invalid. Effect: sets the assumed fluid temperature during a sensor fault (estimate off) Evidence: ledger:E0761, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEB8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x75D" flags="0x0">
    <title>Trans Fluid Temp Substitute - Estimate Model Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inside the substitute estimate: on (stock) runs the coolant / run-time model; off returns the Model Off Value. Effect: off = the estimate returns one fixed value Evidence: ledger:E0761</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCF2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x75E" flags="0x0">
    <title>Trans Fluid Temp Substitute - Model Off Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Substitute fluid temperature returned when the estimate model is turned off. Stock 138 C (not used stock). Effect: sets the substitute with the model off Evidence: ledger:E0761</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEBA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x75F" flags="0x0">
    <title>Trans Fluid Temp Substitute - Hot Engine Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During a fluid temperature sensor fault, once engine coolant is at or above this the substitute is the Hot Engine Value. Stock 110 C. While the transmission range switch reading is invalid the substitute is the Invalid Range Switch Value (stock 141 C) instead of this estimate. Effect: raise = the hot substitute starts at a higher coolant temperature Evidence: ledger:E0761, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEC6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x760" flags="0x0">
    <title>Trans Fluid Temp Substitute - Hot Engine Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Substitute fluid temperature used while coolant is at or above the Hot Engine Threshold. Stock 140 C. While the transmission range switch reading is invalid the substitute is the Invalid Range Switch Value (stock 141 C) instead of this estimate. Effect: sets the fluid temperature assumed with a hot engine during a sensor fault Evidence: ledger:E0761, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEBE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x761" flags="0x0">
    <title>Trans Fluid Temp Substitute - Very Cold Engine Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After the first seconds of run time, coolant below this uses the Very Cold Engine Value; between this and the Hot Engine Threshold the substitute equals coolant temperature. Stock -30 C. Effect: raise = the very-cold substitute is used up to a higher coolant temperature Evidence: ledger:E0761</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEC2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x762" flags="0x0">
    <title>Trans Fluid Temp Substitute - Very Cold Engine Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Substitute fluid temperature used when coolant is below the Very Cold Engine Threshold. Stock 95 C. While the transmission range switch reading is invalid the substitute is the Invalid Range Switch Value (stock 141 C) instead of this estimate. Effect: sets the fluid temperature assumed with a very cold engine during a sensor fault Evidence: ledger:E0761, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x763" flags="0x0">
    <title>Trans Fluid Temp Substitute - Invalid Range Switch Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission fluid temperature the PCM uses while the transmission range switch reading is invalid (no valid range for the confirm time), with the substitute estimate on. Stock 141 C, which is above the hot mode entry temperatures, so the transmission also runs its hot shift and converter clutch schedules then. Effect: lower = a cooler assumed fluid temperature while the range switch reading is invalid Evidence: ledger:E0761, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEBC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x764" flags="0x0">
    <title>Trans Fluid Temp Substitute - Early Run Value (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission fluid temperature used for the first 10 s after start (the start time limit) when Use Intake Temperature at Start is off. Stock 90 C. That switch is on in the stock calibration, so intake air temperature is used instead. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (with the switch off: sets the early fluid temperature) Evidence: ledger:E0761, ledger:E1263</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEC0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x765" flags="0x0">
    <title>Trans Fluid Temp Substitute - Early Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During a fluid temperature sensor fault, for this long after the engine starts the substitute fluid temperature is the intake air temperature (with the stock Use Intake Temperature switch on); after it, the coolant-based estimate takes over. Stock 10.0 s. While the transmission range switch reading is invalid the substitute is the Invalid Range Switch Value (stock 141 C) instead of this estimate. Effect: raise = the intake air temperature is used as the substitute for longer after start Evidence: ledger:E0298, ledger:E0761, ledger:E0791, ledger:E0818, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DED0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x766" flags="0x0">
    <title>Trans Fluid Temp Substitute - Use Intake Temperature at Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On (stock): during a fluid temperature sensor fault in the first seconds after start (Early Run Time), the substitute fluid temperature is the intake air temperature. Off: the fixed Early Run Value is used instead. While the transmission range switch reading is invalid the substitute is the Invalid Range Switch Value (stock 141 C) instead of this estimate. Effect: off = a fixed early-run substitute (stock 90 C) instead of intake air temperature Evidence: ledger:E0298, ledger:E0761, ledger:E0791, ledger:E0818, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DED4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x767" flags="0x0">
    <title>Trans High Pedal Flag - Set Above, 4-Lo</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Set point while the transfer case is in 4-Lo. Stock 56.25 %. When pedal demand rises above the set point the transmission switches to the wide-open-throttle member of its current shift and converter clutch schedule pair and turns on its full-throttle shift rules; it switches back once demand falls below the clear point. Pedal demand here is the driver&#x27;s throttle-area request. Effect: raise = in 4-Lo, full-throttle shifting starts at a higher pedal demand Evidence: ledger:E0761, ledger:E0784, ledger:E0838</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCC0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x768" flags="0x0">
    <title>Trans High Pedal Flag - Clear Below, 4-Lo</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Clear point while the transfer case is in 4-Lo. Stock 50.0 %. Keep it below the set point. When pedal demand rises above the set point the transmission switches to the wide-open-throttle member of its current shift and converter clutch schedule pair and turns on its full-throttle shift rules; it switches back once demand falls below the clear point. Pedal demand here is the driver&#x27;s throttle-area request. Effect: raise = in 4-Lo, full-throttle shifting ends at a higher pedal demand Evidence: ledger:E0761, ledger:E0784, ledger:E0838</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCBE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x769" flags="0x0">
    <title>Trans High Pedal Flag - Set Above, Cruise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Set point while cruise control is engaged (hot transmission mode uses the default pair instead). Stock 99.0 %. When pedal demand rises above the set point the transmission switches to the wide-open-throttle member of its current shift and converter clutch schedule pair and turns on its full-throttle shift rules; it switches back once demand falls below the clear point. Pedal demand here is the driver&#x27;s throttle-area request. Effect: raise = with cruise engaged, full-throttle shifting starts at a higher pedal demand Evidence: ledger:E0761, ledger:E0784, ledger:E0838</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x76A" flags="0x0">
    <title>Trans High Pedal Flag - Clear Below, Cruise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Clear point while cruise control is engaged (hot transmission mode uses the default pair instead). Stock 97.5 %. Keep it below the set point. When pedal demand rises above the set point the transmission switches to the wide-open-throttle member of its current shift and converter clutch schedule pair and turns on its full-throttle shift rules; it switches back once demand falls below the clear point. Pedal demand here is the driver&#x27;s throttle-area request. Effect: raise = with cruise engaged, full-throttle shifting ends at a higher pedal demand Evidence: ledger:E0761, ledger:E0784, ledger:E0838</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCC2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x76B" flags="0x0">
    <title>Trans High Pedal Flag - Set Above, Default</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Set point in normal driving and in hot transmission mode. Stock 96.88 %. When pedal demand rises above the set point the transmission switches to the wide-open-throttle member of its current shift and converter clutch schedule pair and turns on its full-throttle shift rules; it switches back once demand falls below the clear point. Pedal demand here is the driver&#x27;s throttle-area request. Effect: raise = full-throttle shifting starts at a higher pedal demand Evidence: ledger:E0761, ledger:E0784, ledger:E0838</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCBC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x76C" flags="0x0">
    <title>Trans High Pedal Flag - Clear Below, Default</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Clear point in normal driving and in hot transmission mode. Stock 93.75 %. Keep it below the set point. When pedal demand rises above the set point the transmission switches to the wide-open-throttle member of its current shift and converter clutch schedule pair and turns on its full-throttle shift rules; it switches back once demand falls below the clear point. Pedal demand here is the driver&#x27;s throttle-area request. Effect: raise = full-throttle shifting ends at a higher pedal demand Evidence: ledger:E0761, ledger:E0784, ledger:E0838</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCBA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x76D" flags="0x0">
    <title>Transfer Case High Range Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the output speed sensor reading to get transmission output speed while the transfer case is in high range. The sensor sits after the transfer case, so this is the high-range ratio (1.00 on the stock transfer case). Stock 1.00. Change it only for a transfer case whose high range is not 1:1, together with Transfer Case Low Range Ratio. Effect: raise = transmission output speed, and so shift and converter lockup speeds, read higher in high range Evidence: ledger:E0761, ledger:E0808, ledger:E0810</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF1C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>:1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x76E" flags="0x0">
    <title>Transmission Output Speed Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How quickly the filtered transmission output speed follows each new reading, as the fraction of the change taken per update. The filtered speed is what the gear ratio checks, converter clutch logic, torque converter model and several speed diagnostics use, and what the scan tool shows as output speed. Stock 0.10 (10 percent per update). Effect: raise = the filtered output speed reacts faster but is noisier; lower = smoother but lags more Evidence: ledger:E0761, ledger:E0808, ledger:E0810</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF28" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x76F" flags="0x0">
    <title>Transmission Output Speed, Ratio Correction Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On (stock): the output speed sensor reading is corrected by the transfer case ratio (high or low range) to give true transmission output speed. Off, with the two flags below also off, the raw sensor reading is used uncorrected, so shift and lockup speeds would be wrong in 4-Lo. Do not change on a stock driveline. Effect: off = no transfer case ratio correction of output speed Evidence: ledger:E0761, ledger:E0808, ledger:E0810</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF24" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x770" flags="0x0">
    <title>Transmission Output Speed, Axle Ratio Multiply</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When on, transmission output speed is also multiplied by Final Drive Ratio - Transmission Speed, for a speed sensor placed after the axle. Off on the H3 (the sensor reads the transfer case output). Do not turn on for this truck. Effect: on = output speed would read about 4.56 times too high on the stock driveline Evidence: ledger:E0761, ledger:E0808, ledger:E0810</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF26" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x771" flags="0x0">
    <title>Transmission Output Speed, Raw Sensor Bypass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When on, transmission output speed skips all ratio correction and uses the raw sensor reading. Off (stock). Turning it on removes the 4-Lo correction, so shifts and lockup would happen at the wrong speeds in 4-Lo. Effect: on = raw sensor reading used, no transfer case correction Evidence: ledger:E0761, ledger:E0808, ledger:E0810</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF20" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x772" flags="0x0">
    <title>Output Speed Fault, Substitute Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During a transmission output speed sensor fault, how long after each gear change the calculated substitute output speed stays forced in before the PCM&#x27;s normal fault handling takes back over. Stock 2.0 seconds. The output speed fault handling also runs while the transmission range switch reading is invalid. Effect: raise = the substitute output speed value is held longer after each shift before the PCM reverts to its normal fault handling logic Evidence: ledger:E0761, ledger:E0806, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF10" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x773" flags="0x0">
    <title>TCC Tip-In Release - Minimum Time in State (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The tip-in release is only checked once the converter clutch has been in its current control state longer than this (stock 0 s). TCC tip-in release: when the throttle request rises faster than the rate threshold (change per update), the PCM releases the converter clutch and holds it released for the hold time. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: raise = no tip-in release right after a clutch state change Evidence: ledger:E1385</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D458" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x774" flags="0x0">
    <title>TCC Tip-In Release - Hold Time, Applied, Above 255 km/h (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Used only above 255 km/h. Stock 0.5 s. TCC tip-in release: when the throttle request rises faster than the rate threshold (change per update), the PCM releases the converter clutch and holds it released for the hold time. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: no effect on stock (inactive) Evidence: ledger:E0762, ledger:E0807, ledger:E0857</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D45A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x775" flags="0x0">
    <title>TCC Tip-In Release - Hold Time, Clutch Applied (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Used while the clutch is applied, at road speed. Stock 0.5 s. TCC tip-in release: when the throttle request rises faster than the rate threshold (change per update), the PCM releases the converter clutch and holds it released for the hold time. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: no effect on stock (inactive) Evidence: ledger:E0762, ledger:E0807, ledger:E0857</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D45C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x776" flags="0x0">
    <title>TCC Tip-In Release - Rate Threshold, Applied, Modes 0-1 (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Used only in shift modes 0 and 1, which stock never selects. Stock 0 % per update. TCC tip-in release: when the throttle request rises faster than the rate threshold (change per update), the PCM releases the converter clutch and holds it released for the hold time. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: no effect on stock (inactive) Evidence: ledger:E0762, ledger:E0807, ledger:E0857</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D476" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>639.990234</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/102.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x777" flags="0x0">
    <title>TCC Tip-In Release - Rate Threshold, Applied, Modes 0-1, Above 255 km/h (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Never used on stock. Stock 0 % per update. TCC tip-in release: when the throttle request rises faster than the rate threshold (change per update), the PCM releases the converter clutch and holds it released for the hold time. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: no effect on stock (inactive) Evidence: ledger:E0762, ledger:E0857</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D472" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>639.990234</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/102.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x778" flags="0x0">
    <title>TCC Tip-In Release - Rate Threshold, Clutch Applied (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Used while the clutch is applied, at road speed. Stock 100 % per update. TCC tip-in release: when the throttle request rises faster than the rate threshold (change per update), the PCM releases the converter clutch and holds it released for the hold time. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: no effect on stock (inactive) Evidence: ledger:E0762, ledger:E0857</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D474" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>639.990234</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/102.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x779" flags="0x0">
    <title>TCC Tip-In Release - Rate Threshold, Applied, Above 255 km/h (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Used only above 255 km/h, never on the road. Stock 100 % per update. TCC tip-in release: when the throttle request rises faster than the rate threshold (change per update), the PCM releases the converter clutch and holds it released for the hold time. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: no effect on stock (inactive) Evidence: ledger:E0762, ledger:E0857</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D470" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>639.990234</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/102.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x77A" flags="0x0">
    <title>TCC Tip-In Release - Hold Time, Not Applied, Above 255 km/h (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Used only above 255 km/h. Stock 0.5 s. TCC tip-in release: when the throttle request rises faster than the rate threshold (change per update), the PCM releases the converter clutch and holds it released for the hold time. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: no effect on stock (inactive) Evidence: ledger:E0762, ledger:E0807, ledger:E0857</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D460" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x77B" flags="0x0">
    <title>TCC Tip-In Release - Hold Time, Clutch Not Applied (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Used while the clutch is not applied, at road speed. Stock 0.5 s. TCC tip-in release: when the throttle request rises faster than the rate threshold (change per update), the PCM releases the converter clutch and holds it released for the hold time. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: no effect on stock (inactive) Evidence: ledger:E0762, ledger:E0807, ledger:E0857</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D45E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x77C" flags="0x0">
    <title>TCC Tip-In Release - Rate Threshold, Not Applied, Modes 0-1 (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Used only in shift modes 0 and 1, which stock never selects. Stock 0 % per update. TCC tip-in release: when the throttle request rises faster than the rate threshold (change per update), the PCM releases the converter clutch and holds it released for the hold time. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: no effect on stock (inactive) Evidence: ledger:E0762, ledger:E0807, ledger:E0857</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D47E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>639.990234</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/102.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x77D" flags="0x0">
    <title>TCC Tip-In Release - Rate Threshold, Not Applied, Modes 0-1, Above 255 km/h (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Never used on stock. Stock 0 % per update. TCC tip-in release: when the throttle request rises faster than the rate threshold (change per update), the PCM releases the converter clutch and holds it released for the hold time. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: no effect on stock (inactive) Evidence: ledger:E0762, ledger:E0857</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D47A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>639.990234</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/102.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x77E" flags="0x0">
    <title>TCC Tip-In Release - Rate Threshold, Clutch Not Applied (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Used while the clutch is not applied, at road speed. Stock 100 % per update. TCC tip-in release: when the throttle request rises faster than the rate threshold (change per update), the PCM releases the converter clutch and holds it released for the hold time. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: no effect on stock (inactive) Evidence: ledger:E0762, ledger:E0857</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D47C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>639.990234</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/102.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x77F" flags="0x0">
    <title>TCC Tip-In Release - Rate Threshold, Not Applied, Above 255 km/h (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Used only above 255 km/h, never on the road. Stock 100 % per update. TCC tip-in release: when the throttle request rises faster than the rate threshold (change per update), the PCM releases the converter clutch and holds it released for the hold time. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: no effect on stock (inactive) Evidence: ledger:E0762, ledger:E0857</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D478" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>639.990234</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/102.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x780" flags="0x0">
    <title>TCC Slip On Target - Entry Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 0.006 s. How long slip must stay within the entry margin before the PCM moves to on target. With the converter clutch applied the PCM runs one of two phases: on target (slip held close to the slip target) and above target (slip higher than the target, being pulled back in). Effect: raise = slip must settle longer before on target Evidence: ledger:E0762, ledger:E0807, ledger:E0855</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D1AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x781" flags="0x0">
    <title>TCC Slip On Target - Entry Margin</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 50 rpm. The PCM moves to on target once slip stays within this margin of the target, above the speed or torque threshold. With the converter clutch applied the PCM runs one of two phases: on target (slip held close to the slip target) and above target (slip higher than the target, being pulled back in). Effect: raise = the clutch counts as on target with more slip Evidence: ledger:E0762, ledger:E0807, ledger:E0855</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D1B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x782" flags="0x0">
    <title>TCC Slip On Target - Entry Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 28 km/h (transmission-side speed). Entering on target needs speed above this or torque above the entry torque. The PCM moves to on target once slip stays within this margin of the target, above the speed or torque threshold. With the converter clutch applied the PCM runs one of two phases: on target (slip held close to the slip target) and above target (slip higher than the target, being pulled back in). Effect: raise = on target needs a higher speed (or the torque path) Evidence: ledger:E0762, ledger:E0807, ledger:E0855</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D1B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x783" flags="0x0">
    <title>TCC Slip On Target - Entry Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 305 Nm. Entering on target needs torque above this or speed above the entry speed. The PCM moves to on target once slip stays within this margin of the target, above the speed or torque threshold. With the converter clutch applied the PCM runs one of two phases: on target (slip held close to the slip target) and above target (slip higher than the target, being pulled back in). Effect: raise = on target needs more torque (or the speed path) Evidence: ledger:E0762, ledger:E0807, ledger:E0855</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D1B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x784" flags="0x0">
    <title>TCC Slip On Target - Low Speed Exit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 23.5 km/h (transmission-side speed). The PCM also drops back to above target below both the low speed and low torque thresholds. With the converter clutch applied the PCM runs one of two phases: on target (slip held close to the slip target) and above target (slip higher than the target, being pulled back in). Effect: raise = on target ends at a higher speed Evidence: ledger:E0762, ledger:E0823, ledger:E0855</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D43E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x785" flags="0x0">
    <title>TCC Slip On Target - Low Torque Exit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 300 Nm. The PCM also drops back to above target below both the low speed and low torque thresholds. With the converter clutch applied the PCM runs one of two phases: on target (slip held close to the slip target) and above target (slip higher than the target, being pulled back in). Effect: raise = on target ends at a higher torque Evidence: ledger:E0762, ledger:E0823, ledger:E0855</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D43C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x786" flags="0x0">
    <title>TCC Schedule Zone - Hold at Upshift Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The zone is not updated during this time after an upshift is commanded (stock 0 s). The converter clutch logic keeps a schedule zone: below the release speed, between, or at or above the apply speed of the current clutch schedule; the closed throttle apply state and the low baro apply delay use it. The same value also times two clutch checks that are switched off on the stock calibration. Effect: raise = the clutch logic keeps the old zone longer at the start of an upshift Evidence: ledger:E1425</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D50C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x787" flags="0x30">
    <title>TCC Release on Downshift Request - Hold Time by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a downshift is requested the converter clutch is released and held released for this time, by current gear (stock 1.5 s in 1st to 3rd). In 4th gear a separate value is used (stock 0 s: released for one update only). Effect: raise = the clutch stays released longer after a downshift request in that gear Evidence: ledger:E1385</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D268" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x788" flags="0x30">
    <title>TCC Release on Upshift Request - Hold Time by Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When an upshift is requested the converter clutch is released and held released for this time, by shift (1-2, 2-3, 3-4; 0 = no release). The upshift release is switched off on the stock calibration (stock 0 s). The first value is also the hold time after a downshift request in 4th gear (stock 0 s: released for one update only). Effect: 1-2 value: raise = the clutch stays released longer after a downshift request in 4th; the upshift use has no effect on the stock calibration Evidence: ledger:E1389</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D26E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x789" flags="0x0">
    <title>Shift Lamp - Over-Rev Engine Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift lamp request (a data bus signal for a manual transmission upshift lamp): at or above this engine speed the lamp request comes on at once, whatever the other conditions. Stock 5800 rpm. Dormant on this truck: the shift lamp request only runs on the manual transmission software path. Effect: lower = the lamp warns of over-rev earlier Evidence: ledger:E1143</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2CA8C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x78A" flags="0x0">
    <title>Shift Lamp - Warm Engine Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift lamp request (a data bus signal for a manual transmission upshift lamp): the warm engine speed thresholds are used once the engine has run this long and coolant is above the warm coolant value. Stock 10 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E1143</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2CA8A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x78B" flags="0x0">
    <title>Shift Lamp - Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift lamp request (a data bus signal for a manual transmission upshift lamp): no lamp request below this coolant temperature. Stock -10 C. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E1143</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2CA90" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x78C" flags="0x0">
    <title>Shift Lamp - Warm Engine Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift lamp request (a data bus signal for a manual transmission upshift lamp): the warm engine speed thresholds are used at or above this coolant temperature, once the warm run time has passed. Stock 56 C. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E1143</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2CA92" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x78D" flags="0x0">
    <title>First-Run Mode - Idle Base Spark</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First-run mode runs only during the first 12 s of engine running recorded by the PCM (kept through power-off), with a stored flag set, the mode enable set and start-up coolant inside the coolant window. During it the idle base spark is this fixed value instead of the Idle Base Spark table. Stock 16 deg. Effect: raise = more idle spark advance during first-run mode Evidence: ledger:E0763, ledger:E1227</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F3E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x78E" flags="0x30">
    <title>Idle Shift Kick Extended Term - Spark vs Turbine Speed Fall</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark advance added to the idle spark while the idle shift kick extended term is active, by how far the turbine speed rate is below the gear kick bias (0 to 2000 rpm/s). Stock 0. Dormant: the extended term is switched off in this calibration, so it has no effect on this truck&#x27;s software. Effect: raise = more idle spark advance from the shift kick extended term Evidence: ledger:E0763, ledger:E0936, ledger:E1234</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="125" />
      <LABEL index="2" value="250" />
      <LABEL index="3" value="375" />
      <LABEL index="4" value="500" />
      <LABEL index="5" value="625" />
      <LABEL index="6" value="750" />
      <LABEL index="7" value="875" />
      <LABEL index="8" value="1000" />
      <LABEL index="9" value="1125" />
      <LABEL index="10" value="1250" />
      <LABEL index="11" value="1375" />
      <LABEL index="12" value="1500" />
      <LABEL index="13" value="1625" />
      <LABEL index="14" value="1750" />
      <LABEL index="15" value="1875" />
      <LABEL index="16" value="2000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EC68" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x78F" flags="0x30">
    <title>Idle Spark Coolant Advance Multiplier vs Barometric Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the idle spark coolant advance (Park/Neutral and in gear) by barometric pressure. Stock 1.0 at every pressure, so it has no effect. Effect: lower = less idle coolant spark advance at that barometric pressure Evidence: ledger:E0763, ledger:E1220</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2ECB8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x790" flags="0x30">
    <title>Idle Spark Coolant Advance (Park/Neutral)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark advance added to the idle spark in Park or Neutral, by coolant temperature, before the idle maximum and minimum are applied. Scaled by the barometric multiplier. Stock 12 deg cold falling to 2 deg warm. Effect: raise = more idle spark advance at that coolant temperature in Park or Neutral Evidence: ledger:E0763, ledger:E0936, ledger:E1220</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>degC (ECT)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EC8C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x791" flags="0x30">
    <title>Idle Spark Coolant Advance (In Gear)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark advance added to the idle spark in gear, by coolant temperature, before the idle maximum and minimum are applied. Scaled by the barometric multiplier. Stock 10 deg cold falling to 0 warm. Effect: raise = more idle spark advance at that coolant temperature in gear Evidence: ledger:E0763, ledger:E0936, ledger:E1220</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>degC (ECT)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2ECA2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x792" flags="0x0">
    <title>Idle Speed Control - Integral Maximum, Acquire</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: largest airflow the integral term may add while engine speed is coming down to idle. Stock 9 g/s. Effect: raise = the integral may add more air Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2235C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x793" flags="0x0">
    <title>Idle Speed Control - Integral Minimum, Acquire</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: most airflow the integral term may remove while engine speed is coming down to idle. Stock -2 g/s. Effect: lower = the integral may remove more air Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2235E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x794" flags="0x0">
    <title>Idle Speed Control - Proportional Maximum, Acquire</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: largest airflow the proportional term may add while engine speed is coming down to idle. Stock 0, which with the minimum also 0 switches the proportional term off in this state. Effect: raise = the proportional term may add air while acquiring idle Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x223A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x795" flags="0x0">
    <title>Idle Speed Control - Proportional Minimum, Acquire</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: most airflow the proportional term may remove while engine speed is coming down to idle. Stock 0. Effect: lower = the proportional term may remove air while acquiring idle Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x223AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x796" flags="0x30">
    <title>Transmission Fault Reactions by Fault Code (bit mask)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Which protective transmission reactions each fault code switches on. One row per fault code (labelled with the code), 6 bytes = 44 reaction bits; a reaction is on while any code whose row has its bit is failing (for most codes: has failed since codes were last cleared). Bits used on stock, as byte (1 to 6) and bit value: byte 2 0x40 = torque converter clutch kept released; byte 2 0x20 = general transmission fault (blocks converter clutch adaptive learning and is read by the shift and garage engagement logic); byte 2 0x10 = 4WD low high-pedal shift thresholds not used (P2771); byte 2 0x01 = command 3rd gear; byte 3 0x40 = hold...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>byte</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="byte 1" />
      <LABEL index="1" value="byte 2" />
      <LABEL index="2" value="byte 3" />
      <LABEL index="3" value="byte 4" />
      <LABEL index="4" value="byte 5" />
      <LABEL index="5" value="byte 6" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>115</indexcount>
      <units>fault code</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="P0121" />
      <LABEL index="1" value="P0122" />
      <LABEL index="2" value="P0123" />
      <LABEL index="3" value="P0218" />
      <LABEL index="4" value="unused slot 5" />
      <LABEL index="5" value="unused slot 6" />
      <LABEL index="6" value="P0502" />
      <LABEL index="7" value="P0503" />
      <LABEL index="8" value="P0562" />
      <LABEL index="9" value="P0572" />
      <LABEL index="10" value="P0573" />
      <LABEL index="11" value="P0563" />
      <LABEL index="12" value="P0601" />
      <LABEL index="13" value="P0602" />
      <LABEL index="14" value="P0603" />
      <LABEL index="15" value="P0604" />
      <LABEL index="16" value="unused slot 17" />
      <LABEL index="17" value="P0703" />
      <LABEL index="18" value="P0705" />
      <LABEL index="19" value="P0711" />
      <LABEL index="20" value="P0712" />
      <LABEL index="21" value="P0713" />
      <LABEL index="22" value="P0716" />
      <LABEL index="23" value="P0717" />
      <LABEL index="24" value="P0719" />
      <LABEL index="25" value="P0722" />
      <LABEL index="26" value="P0723" />
      <LABEL index="27" value="P0724" />
      <LABEL index="28" value="unused slot 29" />
      <LABEL index="29" value="P0731" />
      <LABEL index="30" value="P0732" />
      <LABEL index="31" value="P0733" />
      <LABEL index="32" value="P0734" />
      <LABEL index="33" value="P0735" />
      <LABEL index="34" value="P0741" />
      <LABEL index="35" value="P0742" />
      <LABEL index="36" value="P0748" />
      <LABEL index="37" value="P0751" />
      <LABEL index="38" value="P0752" />
      <LABEL index="39" value="P0756" />
      <LABEL index="40" value="P0757" />
      <LABEL index="41" value="P0761" />
      <LABEL index="42" value="P0762" />
      <LABEL index="43" value="unused slot 44" />
      <LABEL index="44" value="unused slot 45" />
      <LABEL index="45" value="unused slot 46" />
      <LABEL index="46" value="P0120" />
      <LABEL index="47" value="unused slot 48" />
      <LABEL index="48" value="unused slot 49" />
      <LABEL index="49" value="P0220" />
      <LABEL index="50" value="P2135" />
      <LABEL index="51" value="P2138" />
      <LABEL index="52" value="P2120" />
      <LABEL index="53" value="P2125" />
      <LABEL index="54" value="P2176" />
      <LABEL index="55" value="P0068" />
      <LABEL index="56" value="P2101" />
      <LABEL index="57" value="P1516" />
      <LABEL index="58" value="P2119" />
      <LABEL index="59" value="P1574" />
      <LABEL index="60" value="P1575" />
      <LABEL index="61" value="P062F" />
      <LABEL index="62" value="P060D" />
      <LABEL index="63" value="P060E" />
      <LABEL index="64" value="P1682" />
      <LABEL index="65" value="P1750" />
      <LABEL index="66" value="unused slot 67" />
      <LABEL index="67" value="P2544" />
      <LABEL index="68" value="unused slot 69" />
      <LABEL index="69" value="unused slot 70" />
      <LABEL index="70" value="unused slot 71" />
      <LABEL index="71" value="unused slot 72" />
      <LABEL index="72" value="P278A" />
      <LABEL index="73" value="P1810" />
      <LABEL index="74" value="P1811" />
      <LABEL index="75" value="P1814" />
      <LABEL index="76" value="P1815" />
      <LABEL index="77" value="P1816" />
      <LABEL index="78" value="P1817" />
      <LABEL index="79" value="P1818" />
      <LABEL index="80" value="P1819" />
      <LABEL index="81" value="P1820" />
      <LABEL index="82" value="P1822" />
      <LABEL index="83" value="P1823" />
      <LABEL index="84" value="P1825" />
      <LABEL index="85" value="P1826" />
      <LABEL index="86" value="unused slot 87" />
      <LABEL index="87" value="unused slot 88" />
      <LABEL index="88" value="unused slot 89" />
      <LABEL index="89" value="unused slot 90" />
      <LABEL index="90" value="P0973" />
      <LABEL index="91" value="P0974" />
      <LABEL index="92" value="P0976" />
      <LABEL index="93" value="P0977" />
      <LABEL index="94" value="P0787" />
      <LABEL index="95" value="P0788" />
      <LABEL index="96" value="P2769" />
      <LABEL index="97" value="P2770" />
      <LABEL index="98" value="P0979" />
      <LABEL index="99" value="P0980" />
      <LABEL index="100" value="P2764" />
      <LABEL index="101" value="P2763" />
      <LABEL index="102" value="P0897" />
      <LABEL index="103" value="P0894" />
      <LABEL index="104" value="P2771" />
      <LABEL index="105" value="unused slot 106" />
      <LABEL index="106" value="unused slot 107" />
      <LABEL index="107" value="P1887" />
      <LABEL index="108" value="unused slot 109" />
      <LABEL index="109" value="unused slot 110" />
      <LABEL index="110" value="unused slot 111" />
      <LABEL index="111" value="unused slot 112" />
      <LABEL index="112" value="unused slot 113" />
      <LABEL index="113" value="unused slot 114" />
      <LABEL index="114" value="unused slot 115" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F8D0" mmedelementsizebits="8" mmedrowcount="115" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>bit mask</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x797" flags="0x30">
    <title>Trans Fault Reaction - Enable While Failing, by Code</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. One value per fault-code slot (each column is labelled with the trouble code of its slot): non-zero lets that code drive its transmission fault reactions while the fault is failing now; the reaction ends when the test passes again. Stock: on for P0218, P0711, P0719 and P0724. Effect: DO NOT EDIT unless you know which fault reaction you are changing Evidence: ledger:E0765, ledger:E0770, ledger:E1084</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>115</indexcount>
      <units>fault code slot</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="P0121" />
      <LABEL index="1" value="P0122" />
      <LABEL index="2" value="P0123" />
      <LABEL index="3" value="P0218" />
      <LABEL index="4" value="unused" />
      <LABEL index="5" value="unused" />
      <LABEL index="6" value="P0502" />
      <LABEL index="7" value="P0503" />
      <LABEL index="8" value="P0562" />
      <LABEL index="9" value="P0572" />
      <LABEL index="10" value="P0573" />
      <LABEL index="11" value="P0563" />
      <LABEL index="12" value="P0601" />
      <LABEL index="13" value="P0602" />
      <LABEL index="14" value="P0603" />
      <LABEL index="15" value="P0604" />
      <LABEL index="16" value="unused" />
      <LABEL index="17" value="P0703" />
      <LABEL index="18" value="P0705" />
      <LABEL index="19" value="P0711" />
      <LABEL index="20" value="P0712" />
      <LABEL index="21" value="P0713" />
      <LABEL index="22" value="P0716" />
      <LABEL index="23" value="P0717" />
      <LABEL index="24" value="P0719" />
      <LABEL index="25" value="P0722" />
      <LABEL index="26" value="P0723" />
      <LABEL index="27" value="P0724" />
      <LABEL index="28" value="unused" />
      <LABEL index="29" value="P0731" />
      <LABEL index="30" value="P0732" />
      <LABEL index="31" value="P0733" />
      <LABEL index="32" value="P0734" />
      <LABEL index="33" value="P0735" />
      <LABEL index="34" value="P0741" />
      <LABEL index="35" value="P0742" />
      <LABEL index="36" value="P0748" />
      <LABEL index="37" value="P0751" />
      <LABEL index="38" value="P0752" />
      <LABEL index="39" value="P0756" />
      <LABEL index="40" value="P0757" />
      <LABEL index="41" value="P0761" />
      <LABEL index="42" value="P0762" />
      <LABEL index="43" value="unused" />
      <LABEL index="44" value="unused" />
      <LABEL index="45" value="unused" />
      <LABEL index="46" value="P0120" />
      <LABEL index="47" value="unused" />
      <LABEL index="48" value="unused" />
      <LABEL index="49" value="P0220" />
      <LABEL index="50" value="P2135" />
      <LABEL index="51" value="P2138" />
      <LABEL index="52" value="P2120" />
      <LABEL index="53" value="P2125" />
      <LABEL index="54" value="P2176" />
      <LABEL index="55" value="P0068" />
      <LABEL index="56" value="P2101" />
      <LABEL index="57" value="P1516" />
      <LABEL index="58" value="P2119" />
      <LABEL index="59" value="P1574" />
      <LABEL index="60" value="P1575" />
      <LABEL index="61" value="P062F" />
      <LABEL index="62" value="P060D" />
      <LABEL index="63" value="P060E" />
      <LABEL index="64" value="P1682" />
      <LABEL index="65" value="P1750" />
      <LABEL index="66" value="unused" />
      <LABEL index="67" value="P2544" />
      <LABEL index="68" value="unused" />
      <LABEL index="69" value="unused" />
      <LABEL index="70" value="unused" />
      <LABEL index="71" value="unused" />
      <LABEL index="72" value="P278A" />
      <LABEL index="73" value="P1810" />
      <LABEL index="74" value="P1811" />
      <LABEL index="75" value="P1814" />
      <LABEL index="76" value="P1815" />
      <LABEL index="77" value="P1816" />
      <LABEL index="78" value="P1817" />
      <LABEL index="79" value="P1818" />
      <LABEL index="80" value="P1819" />
      <LABEL index="81" value="P1820" />
      <LABEL index="82" value="P1822" />
      <LABEL index="83" value="P1823" />
      <LABEL index="84" value="P1825" />
      <LABEL index="85" value="P1826" />
      <LABEL index="86" value="unused" />
      <LABEL index="87" value="unused" />
      <LABEL index="88" value="unused" />
      <LABEL index="89" value="unused" />
      <LABEL index="90" value="P0973" />
      <LABEL index="91" value="P0974" />
      <LABEL index="92" value="P0976" />
      <LABEL index="93" value="P0977" />
      <LABEL index="94" value="P0787" />
      <LABEL index="95" value="P0788" />
      <LABEL index="96" value="P2769" />
      <LABEL index="97" value="P2770" />
      <LABEL index="98" value="P0979" />
      <LABEL index="99" value="P0980" />
      <LABEL index="100" value="P2764" />
      <LABEL index="101" value="P2763" />
      <LABEL index="102" value="P0897" />
      <LABEL index="103" value="P0894" />
      <LABEL index="104" value="P2771" />
      <LABEL index="105" value="unused" />
      <LABEL index="106" value="unused" />
      <LABEL index="107" value="P1887" />
      <LABEL index="108" value="unused" />
      <LABEL index="109" value="unused" />
      <LABEL index="110" value="unused" />
      <LABEL index="111" value="unused" />
      <LABEL index="112" value="unused" />
      <LABEL index="113" value="unused" />
      <LABEL index="114" value="unused" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3FC28" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="115" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flag</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x798" flags="0x30">
    <title>Trans Fault Reaction - Enable Until Codes Cleared, by Code</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. One value per fault-code slot (each column is labelled with the trouble code of its slot): non-zero lets that code drive its transmission fault reactions from the moment it has failed until the codes are cleared with a scan tool or age out, so the reaction stays on after the fault stops. Stock: on for 31 codes. A slot with both this and the failing-now enable at zero has no reaction. Effect: DO NOT EDIT unless you know which fault reaction you are changing Evidence: ledger:E0765, ledger:E0770, ledger:E1084</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>115</indexcount>
      <units>fault code slot</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="P0121" />
      <LABEL index="1" value="P0122" />
      <LABEL index="2" value="P0123" />
      <LABEL index="3" value="P0218" />
      <LABEL index="4" value="unused" />
      <LABEL index="5" value="unused" />
      <LABEL index="6" value="P0502" />
      <LABEL index="7" value="P0503" />
      <LABEL index="8" value="P0562" />
      <LABEL index="9" value="P0572" />
      <LABEL index="10" value="P0573" />
      <LABEL index="11" value="P0563" />
      <LABEL index="12" value="P0601" />
      <LABEL index="13" value="P0602" />
      <LABEL index="14" value="P0603" />
      <LABEL index="15" value="P0604" />
      <LABEL index="16" value="unused" />
      <LABEL index="17" value="P0703" />
      <LABEL index="18" value="P0705" />
      <LABEL index="19" value="P0711" />
      <LABEL index="20" value="P0712" />
      <LABEL index="21" value="P0713" />
      <LABEL index="22" value="P0716" />
      <LABEL index="23" value="P0717" />
      <LABEL index="24" value="P0719" />
      <LABEL index="25" value="P0722" />
      <LABEL index="26" value="P0723" />
      <LABEL index="27" value="P0724" />
      <LABEL index="28" value="unused" />
      <LABEL index="29" value="P0731" />
      <LABEL index="30" value="P0732" />
      <LABEL index="31" value="P0733" />
      <LABEL index="32" value="P0734" />
      <LABEL index="33" value="P0735" />
      <LABEL index="34" value="P0741" />
      <LABEL index="35" value="P0742" />
      <LABEL index="36" value="P0748" />
      <LABEL index="37" value="P0751" />
      <LABEL index="38" value="P0752" />
      <LABEL index="39" value="P0756" />
      <LABEL index="40" value="P0757" />
      <LABEL index="41" value="P0761" />
      <LABEL index="42" value="P0762" />
      <LABEL index="43" value="unused" />
      <LABEL index="44" value="unused" />
      <LABEL index="45" value="unused" />
      <LABEL index="46" value="P0120" />
      <LABEL index="47" value="unused" />
      <LABEL index="48" value="unused" />
      <LABEL index="49" value="P0220" />
      <LABEL index="50" value="P2135" />
      <LABEL index="51" value="P2138" />
      <LABEL index="52" value="P2120" />
      <LABEL index="53" value="P2125" />
      <LABEL index="54" value="P2176" />
      <LABEL index="55" value="P0068" />
      <LABEL index="56" value="P2101" />
      <LABEL index="57" value="P1516" />
      <LABEL index="58" value="P2119" />
      <LABEL index="59" value="P1574" />
      <LABEL index="60" value="P1575" />
      <LABEL index="61" value="P062F" />
      <LABEL index="62" value="P060D" />
      <LABEL index="63" value="P060E" />
      <LABEL index="64" value="P1682" />
      <LABEL index="65" value="P1750" />
      <LABEL index="66" value="unused" />
      <LABEL index="67" value="P2544" />
      <LABEL index="68" value="unused" />
      <LABEL index="69" value="unused" />
      <LABEL index="70" value="unused" />
      <LABEL index="71" value="unused" />
      <LABEL index="72" value="P278A" />
      <LABEL index="73" value="P1810" />
      <LABEL index="74" value="P1811" />
      <LABEL index="75" value="P1814" />
      <LABEL index="76" value="P1815" />
      <LABEL index="77" value="P1816" />
      <LABEL index="78" value="P1817" />
      <LABEL index="79" value="P1818" />
      <LABEL index="80" value="P1819" />
      <LABEL index="81" value="P1820" />
      <LABEL index="82" value="P1822" />
      <LABEL index="83" value="P1823" />
      <LABEL index="84" value="P1825" />
      <LABEL index="85" value="P1826" />
      <LABEL index="86" value="unused" />
      <LABEL index="87" value="unused" />
      <LABEL index="88" value="unused" />
      <LABEL index="89" value="unused" />
      <LABEL index="90" value="P0973" />
      <LABEL index="91" value="P0974" />
      <LABEL index="92" value="P0976" />
      <LABEL index="93" value="P0977" />
      <LABEL index="94" value="P0787" />
      <LABEL index="95" value="P0788" />
      <LABEL index="96" value="P2769" />
      <LABEL index="97" value="P2770" />
      <LABEL index="98" value="P0979" />
      <LABEL index="99" value="P0980" />
      <LABEL index="100" value="P2764" />
      <LABEL index="101" value="P2763" />
      <LABEL index="102" value="P0897" />
      <LABEL index="103" value="P0894" />
      <LABEL index="104" value="P2771" />
      <LABEL index="105" value="unused" />
      <LABEL index="106" value="unused" />
      <LABEL index="107" value="P1887" />
      <LABEL index="108" value="unused" />
      <LABEL index="109" value="unused" />
      <LABEL index="110" value="unused" />
      <LABEL index="111" value="unused" />
      <LABEL index="112" value="unused" />
      <LABEL index="113" value="unused" />
      <LABEL index="114" value="unused" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3FD10" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="115" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flag</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x799" flags="0x0">
    <title>P0788 Fail - Fault Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0788 (3-2 shift solenoid circuit check while commanded on): fault samples inside the window that set the code. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the fault must be present for more of the window Evidence: ledger:E1097</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F4F2" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x79A" flags="0x0">
    <title>P0788 Pass - Good Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0788 (3-2 shift solenoid circuit check while commanded on): good samples inside the window that pass the check. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the circuit must read good for more of the window Evidence: ledger:E1097</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F4F3" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x79B" flags="0x0">
    <title>P0788 Test - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0788 (3-2 shift solenoid circuit check while commanded on): length of the sample window. Stock 5 s. Keep it above the fail and pass times, or the check can never report. Effect: raise = fault samples may be spread over a longer time Evidence: ledger:E1097</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F4F4" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x79C" flags="0x0">
    <title>P0787 Fail - Fault Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0787 (3-2 shift solenoid circuit check while commanded off): fault samples inside the window that set the code. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the fault must be present for more of the window Evidence: ledger:E1097</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F4F8" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x79D" flags="0x0">
    <title>P0787 Pass - Good Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0787 (3-2 shift solenoid circuit check while commanded off): good samples inside the window that pass the check. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the circuit must read good for more of the window Evidence: ledger:E1097</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F4F9" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x79E" flags="0x0">
    <title>P0787 Test - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0787 (3-2 shift solenoid circuit check while commanded off): length of the sample window. Stock 5 s. Keep it above the fail and pass times, or the check can never report. Effect: raise = fault samples may be spread over a longer time Evidence: ledger:E1097</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F4FA" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x79F" flags="0x0">
    <title>P0973 Pass - Good Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0973 (shift solenoid A circuit check while commanded off): good samples inside the window that pass the check. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the circuit must read good for more of the window Evidence: ledger:E1097</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F51F" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A0" flags="0x0">
    <title>P0973 Test - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0973 (shift solenoid A circuit check while commanded off): length of the sample window. Stock 5 s. Keep it above the fail and pass times, or the check can never report. Effect: raise = fault samples may be spread over a longer time Evidence: ledger:E1097</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F520" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A1" flags="0x0">
    <title>P0974 Pass - Good Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0974 (shift solenoid A circuit check while commanded on): good samples inside the window that pass the check. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the circuit must read good for more of the window Evidence: ledger:E1097</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F522" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A2" flags="0x0">
    <title>P0974 Test - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0974 (shift solenoid A circuit check while commanded on): length of the sample window. Stock 5 s. Keep it above the fail and pass times, or the check can never report. Effect: raise = fault samples may be spread over a longer time Evidence: ledger:E1097</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F523" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A3" flags="0x0">
    <title>P0976 Pass - Good Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0976 (shift solenoid B circuit check while commanded off): good samples inside the window that pass the check. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the circuit must read good for more of the window Evidence: ledger:E1097</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F543" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A4" flags="0x0">
    <title>P0976 Test - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0976 (shift solenoid B circuit check while commanded off): length of the sample window. Stock 5 s. Keep it above the fail and pass times, or the check can never report. Effect: raise = fault samples may be spread over a longer time Evidence: ledger:E1097</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F544" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A5" flags="0x0">
    <title>P0977 Pass - Good Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0977 (shift solenoid B circuit check while commanded on): good samples inside the window that pass the check. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the circuit must read good for more of the window Evidence: ledger:E1097</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F546" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A6" flags="0x0">
    <title>P0977 Test - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0977 (shift solenoid B circuit check while commanded on): length of the sample window. Stock 5 s. Keep it above the fail and pass times, or the check can never report. Effect: raise = fault samples may be spread over a longer time Evidence: ledger:E1097</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F547" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A7" flags="0x0">
    <title>Shift Sol A Performance (P0751), 1st Gear - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest driver throttle-area request at which the shift solenoid A performance test (P0751) watches the transmission in 1st gear. Stock 25 %. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at a larger throttle request Evidence: ledger:E0766, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F604" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A8" flags="0x0">
    <title>Shift Sol A Performance (P0751), 1st Gear - Torque Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest engine torque at which the shift solenoid A performance test (P0751) watches the transmission in 1st gear. Stock 550 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: lower = the test stops running at a lower engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A9" flags="0x0">
    <title>Shift Sol Tests, 1st Gear Ratio Confirm - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid performance tests, 1st gear commanded: time the ratio must stay inside the right ratio window without a break. Stock 1 s. Effect: raise = the right ratio must last longer Evidence: ledger:E1098</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5C2" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7AA" flags="0x0">
    <title>Shift Sol Tests, 3rd Gear Ratio Confirm - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid performance tests, 3rd gear commanded: time the ratio must stay inside the right ratio window without a break. Stock 1 s. Effect: raise = the right ratio must last longer Evidence: ledger:E1098</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5C3" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7AB" flags="0x0">
    <title>Shift Sol Tests, 2nd Gear Ratio Confirm - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid performance tests, 2nd gear commanded: time the ratio must stay inside the right ratio window without a break. Stock 1 s. Effect: raise = the right ratio must last longer Evidence: ledger:E1098</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5C4" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7AC" flags="0x0">
    <title>Shift Sol Tests, 4th Gear Ratio Confirm - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid performance tests, 4th gear commanded: time the ratio must stay inside the right ratio window without a break. Stock 1 s. Effect: raise = the right ratio must last longer Evidence: ledger:E1098</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5C5" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7AD" flags="0x0">
    <title>Shift Sol A Performance (P0751), 1st Gear - Torque Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest engine torque at which the shift solenoid A performance test (P0751) watches the transmission in 1st gear. Stock 55 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at higher engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7AE" flags="0x0">
    <title>Shift Sol A Performance (P0751), 1st Gear - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time since the last shift that must pass before the shift solenoid A performance test (P0751) watches the transmission in 1st gear. Stock 2 s. The other conditions of the same check (throttle, torque and a converter speed ratio minimum) must hold as well. Effect: raise = the ratio check in 1st gear waits longer after a shift before it can run Evidence: ledger:E0766, ledger:E0806</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7AF" flags="0x0">
    <title>Shift Sol Ratio Tests (P0751 / P0752 / P0756 / P0757) - Run Condition, Fluid Temperature Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The four shift solenoid performance tests run only with transmission fluid at or below this. Stock 130 C. Effect: lower = the tests stop at lower fluid temperature Evidence: ledger:E1098</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F570" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B0" flags="0x0">
    <title>Shift Sol Ratio Tests (P0751 / P0752 / P0756 / P0757) - Run Condition, Fluid Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The four shift solenoid performance tests run only with transmission fluid at or above this. Stock 20 C. Effect: raise = the tests need warmer fluid Evidence: ledger:E1098</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F572" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B1" flags="0x0">
    <title>Shift Sol Ratio Tests (P0751 / P0752 / P0756 / P0757) - Run Condition, Output Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The four shift solenoid performance tests run only with transmission output speed at or above this. Stock 10 rpm. Effect: raise = the tests need more output speed Evidence: ledger:E1098</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F578" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B2" flags="0x0">
    <title>Shift Sol Tests, 1st Gear Ratio Confirm - Ratio Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid performance tests, 1st gear commanded: top of the estimated gear ratio window that counts as the right gear. Stock window 2.890 to 3.300. Held for the confirm time, the right ratio gives the 1st gear half of the pass of P0751 and P0756 and clears a pending wrong ratio observation in that gear. Effect: lower = higher ratios no longer count as the right gear Evidence: ledger:E1098</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F582" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B3" flags="0x0">
    <title>Shift Sol Tests, 1st Gear Ratio Confirm - Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid performance tests, 1st gear commanded: bottom of the estimated gear ratio window that counts as the right gear. Stock window 2.890 to 3.300. Held for the confirm time, the right ratio gives the 1st gear half of the pass of P0751 and P0756 and clears a pending wrong ratio observation in that gear. Effect: raise = lower ratios no longer count as the right gear Evidence: ledger:E1098</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F584" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B4" flags="0x0">
    <title>Shift Sol Tests, 3rd Gear Ratio Confirm - Ratio Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid performance tests, 3rd gear commanded: top of the estimated gear ratio window that counts as the right gear. Stock window 0.950 to 1.240. Held for the confirm time, the right ratio gives the 3rd gear half of the pass of P0752 and P0757 and clears a pending wrong ratio observation in that gear. Effect: lower = higher ratios no longer count as the right gear Evidence: ledger:E1098</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F586" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B5" flags="0x0">
    <title>Shift Sol Tests, 3rd Gear Ratio Confirm - Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid performance tests, 3rd gear commanded: bottom of the estimated gear ratio window that counts as the right gear. Stock window 0.950 to 1.240. Held for the confirm time, the right ratio gives the 3rd gear half of the pass of P0752 and P0757 and clears a pending wrong ratio observation in that gear. Effect: raise = lower ratios no longer count as the right gear Evidence: ledger:E1098</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F588" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B6" flags="0x0">
    <title>Shift Sol Tests, 2nd Gear Ratio Confirm - Ratio Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid performance tests, 2nd gear commanded: top of the estimated gear ratio window that counts as the right gear. Stock window 1.500 to 2.200. Held for the confirm time, the right ratio gives the 2nd gear half of the pass of P0752 and P0756 and clears a pending wrong ratio observation in that gear. Effect: lower = higher ratios no longer count as the right gear Evidence: ledger:E1098</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F58A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B7" flags="0x0">
    <title>Shift Sol Tests, 2nd Gear Ratio Confirm - Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid performance tests, 2nd gear commanded: bottom of the estimated gear ratio window that counts as the right gear. Stock window 1.500 to 2.200. Held for the confirm time, the right ratio gives the 2nd gear half of the pass of P0752 and P0756 and clears a pending wrong ratio observation in that gear. Effect: raise = lower ratios no longer count as the right gear Evidence: ledger:E1098</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F58C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B8" flags="0x0">
    <title>Shift Sol Tests, 4th Gear Ratio Confirm - Ratio Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid performance tests, 4th gear commanded: top of the estimated gear ratio window that counts as the right gear. Stock window 0.650 to 0.900. Held for the confirm time, the right ratio gives the 4th gear half of the pass of P0751 and P0757 and clears a pending wrong ratio observation in that gear. Effect: lower = higher ratios no longer count as the right gear Evidence: ledger:E1098</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F58E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B9" flags="0x0">
    <title>Shift Sol Tests, 4th Gear Ratio Confirm - Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid performance tests, 4th gear commanded: bottom of the estimated gear ratio window that counts as the right gear. Stock window 0.650 to 0.900. Held for the confirm time, the right ratio gives the 4th gear half of the pass of P0751 and P0757 and clears a pending wrong ratio observation in that gear. Effect: raise = lower ratios no longer count as the right gear Evidence: ledger:E1098</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F590" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7BA" flags="0x0">
    <title>Shift Sol A Performance (P0751), 1st Gear - Converter Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest converter speed ratio at which the shift solenoid A performance test (P0751) watches the transmission in 1st gear. Stock 0.62. The converter speed ratio here is the PCM&#x27;s own torque converter model estimate (turbine speed over engine speed, from engine speed and torque): 1.00 = coupled, low values = high slip. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test waits until the converter is closer to coupled Evidence: ledger:E0766, ledger:E0841, ledger:E0851</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F596" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7BB" flags="0x0">
    <title>Shift Sol A Performance (P0751), 4th Gear - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time since the last shift that must pass before the shift solenoid A performance test (P0751) watches the transmission in 4th gear. Stock 2.5 s. The other conditions of the same check (throttle, torque and a converter speed ratio minimum) must hold as well. Effect: raise = the ratio check in 3rd/4th gear waits longer after a shift before it can run Evidence: ledger:E0766, ledger:E0806</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7BC" flags="0x0">
    <title>Shift Sol A Performance (P0751), 4th Gear - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest driver throttle-area request at which the shift solenoid A performance test (P0751) watches the transmission in 4th gear. Stock 25 %. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at a larger throttle request Evidence: ledger:E0766, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F606" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7BD" flags="0x0">
    <title>Shift Sol A Performance (P0751), 4th Gear - Torque Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest engine torque at which the shift solenoid A performance test (P0751) watches the transmission in 4th gear. Stock 550 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: lower = the test stops running at a lower engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7BE" flags="0x0">
    <title>Shift Sol A Performance (P0751), 4th Gear - Torque Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest engine torque at which the shift solenoid A performance test (P0751) watches the transmission in 4th gear. Stock 55 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at higher engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7BF" flags="0x0">
    <title>Shift Sol A Performance (P0751), 4th Gear - Converter Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest converter speed ratio at which the shift solenoid A performance test (P0751) watches the transmission in 4th gear. Stock 0.85. The converter speed ratio here is the PCM&#x27;s own torque converter model estimate (turbine speed over engine speed, from engine speed and torque): 1.00 = coupled, low values = high slip. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test waits until the converter is closer to coupled Evidence: ledger:E0766, ledger:E0841, ledger:E0851</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F598" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7C0" flags="0x0">
    <title>Shift Sol A Stuck On (P0752), 2nd Gear - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest driver throttle-area request at which the shift solenoid A stuck-on test (P0752) watches the transmission in 2nd gear. Stock 25 %. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at a larger throttle request Evidence: ledger:E0766, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F608" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7C1" flags="0x0">
    <title>Shift Sol A Stuck On (P0752), 2nd Gear - Torque Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest engine torque at which the shift solenoid A stuck-on test (P0752) watches the transmission in 2nd gear. Stock 550 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: lower = the test stops running at a lower engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7C2" flags="0x0">
    <title>Shift Sol A Stuck On (P0752), 2nd Gear - Torque Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest engine torque at which the shift solenoid A stuck-on test (P0752) watches the transmission in 2nd gear. Stock 40 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at higher engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7C3" flags="0x0">
    <title>Shift Sol A Stuck On (P0752), 2nd Gear - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time since the last shift that must pass before the shift solenoid A stuck-on test (P0752) watches the transmission in 2nd gear. Stock 1.5 s. The other conditions of the same check (throttle, torque and a converter speed ratio minimum) must hold as well. Effect: raise = the ratio check in 2nd gear waits longer after a shift before it can run Evidence: ledger:E0766, ledger:E0806</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7C4" flags="0x0">
    <title>Shift Sol A Stuck On (P0752), 2nd Gear - Converter Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest converter speed ratio at which the shift solenoid A stuck-on test (P0752) watches the transmission in 2nd gear. Stock 0.62. The converter speed ratio here is the PCM&#x27;s own torque converter model estimate (turbine speed over engine speed, from engine speed and torque): 1.00 = coupled, low values = high slip. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test waits until the converter is closer to coupled Evidence: ledger:E0766, ledger:E0841, ledger:E0851</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F59A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7C5" flags="0x0">
    <title>Shift Sol A Stuck On (P0752), 3rd Gear - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest driver throttle-area request at which the shift solenoid A stuck-on test (P0752) watches the transmission in 3rd gear. Stock 25 %. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at a larger throttle request Evidence: ledger:E0766, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F60A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7C6" flags="0x0">
    <title>Shift Sol A Stuck On (P0752), 3rd Gear - Torque Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest engine torque at which the shift solenoid A stuck-on test (P0752) watches the transmission in 3rd gear. Stock 550 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: lower = the test stops running at a lower engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7C7" flags="0x0">
    <title>Shift Sol A Stuck On (P0752), 3rd Gear - Torque Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest engine torque at which the shift solenoid A stuck-on test (P0752) watches the transmission in 3rd gear. Stock 65 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at higher engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7C8" flags="0x0">
    <title>Shift Sol A Stuck On (P0752), 3rd Gear - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time since the last shift that must pass before the shift solenoid A stuck-on test (P0752) watches the transmission in 3rd gear. Stock 3 s. The other conditions of the same check (throttle, torque and a converter speed ratio minimum) must hold as well. Effect: raise = the ratio check in 3rd gear waits longer after a shift before it can run Evidence: ledger:E0766, ledger:E0806</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7C9" flags="0x0">
    <title>Shift Sol A Stuck On (P0752), 3rd Gear - Converter Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest converter speed ratio at which the shift solenoid A stuck-on test (P0752) watches the transmission in 3rd gear. Stock 0.58. The converter speed ratio here is the PCM&#x27;s own torque converter model estimate (turbine speed over engine speed, from engine speed and torque): 1.00 = coupled, low values = high slip. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test waits until the converter is closer to coupled Evidence: ledger:E0766, ledger:E0841, ledger:E0851</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F59C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7CA" flags="0x0">
    <title>Shift Sol B Performance (P0756), 2nd Gear - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest driver throttle-area request at which the shift solenoid B performance test (P0756) watches the transmission in 2nd gear. Stock 25 %. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at a larger throttle request Evidence: ledger:E0766, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F60E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7CB" flags="0x0">
    <title>Shift Sol B Performance (P0756), 2nd Gear - Torque Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest engine torque at which the shift solenoid B performance test (P0756) watches the transmission in 2nd gear. Stock 550 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: lower = the test stops running at a lower engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7CC" flags="0x0">
    <title>Shift Sol B Performance (P0756), 2nd Gear - Torque Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest engine torque at which the shift solenoid B performance test (P0756) watches the transmission in 2nd gear. Stock 65 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at higher engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7CD" flags="0x0">
    <title>Shift Sol B Performance (P0756), 2nd Gear - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time since the last shift that must pass before the shift solenoid B performance test (P0756) watches the transmission in 2nd gear. Stock 1 s. The other conditions of the same check (throttle, torque and a converter speed ratio minimum) must hold as well. Effect: raise = the ratio check in 2nd gear waits longer after a shift before it can run Evidence: ledger:E0766, ledger:E0806</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7CE" flags="0x0">
    <title>Shift Sol B Performance (P0756), 2nd Gear - Converter Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest converter speed ratio at which the shift solenoid B performance test (P0756) watches the transmission in 2nd gear. Stock 0.5. The converter speed ratio here is the PCM&#x27;s own torque converter model estimate (turbine speed over engine speed, from engine speed and torque): 1.00 = coupled, low values = high slip. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test waits until the converter is closer to coupled Evidence: ledger:E0766, ledger:E0841, ledger:E0851</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7CF" flags="0x0">
    <title>Shift Sol B Stuck On (P0757), 3rd Gear - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest driver throttle-area request at which the shift solenoid B stuck-on test (P0757) watches the transmission in 3rd gear. Stock 25 %. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at a larger throttle request Evidence: ledger:E0766, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F610" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7D0" flags="0x0">
    <title>Shift Sol B Stuck On (P0757), 3rd Gear - Torque Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest engine torque at which the shift solenoid B stuck-on test (P0757) watches the transmission in 3rd gear. Stock 550 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: lower = the test stops running at a lower engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7D1" flags="0x0">
    <title>Shift Sol B Stuck On (P0757), 3rd Gear - Torque Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest engine torque at which the shift solenoid B stuck-on test (P0757) watches the transmission in 3rd gear. Stock 45 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at higher engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5D4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7D2" flags="0x0">
    <title>Shift Sol B Stuck On (P0757), 3rd Gear - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time since the last shift that must pass before the shift solenoid B stuck-on test (P0757) watches the transmission in 3rd gear. Stock 2.5 s. The other conditions of the same check (throttle, torque and a converter speed ratio minimum) must hold as well. Effect: raise = the ratio check in 3rd gear waits longer after a shift before it can run Evidence: ledger:E0766, ledger:E0806</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7D3" flags="0x0">
    <title>Shift Sol B Stuck On (P0757), 3rd Gear - Converter Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest converter speed ratio at which the shift solenoid B stuck-on test (P0757) watches the transmission in 3rd gear. Stock 0.82. The converter speed ratio here is the PCM&#x27;s own torque converter model estimate (turbine speed over engine speed, from engine speed and torque): 1.00 = coupled, low values = high slip. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test waits until the converter is closer to coupled Evidence: ledger:E0766, ledger:E0841, ledger:E0851</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7D4" flags="0x0">
    <title>Shift Sol B Stuck On (P0757), 4th Gear - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest driver throttle-area request at which the shift solenoid B stuck-on test (P0757) watches the transmission in 4th gear. Stock 25 %. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at a larger throttle request Evidence: ledger:E0766, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F612" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7D5" flags="0x0">
    <title>Shift Sol B Stuck On (P0757), 4th Gear - Torque Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest engine torque at which the shift solenoid B stuck-on test (P0757) watches the transmission in 4th gear. Stock 550 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: lower = the test stops running at a lower engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7D6" flags="0x0">
    <title>Shift Sol B Stuck On (P0757), 4th Gear - Torque Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest engine torque at which the shift solenoid B stuck-on test (P0757) watches the transmission in 4th gear. Stock 0 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at higher engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5D6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7D7" flags="0x0">
    <title>Shift Sol B Stuck On (P0757), 4th Gear - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time since the last shift that must pass before the shift solenoid B stuck-on test (P0757) watches the transmission in 4th gear. Stock 1 s. The other conditions of the same check (throttle, torque and a converter speed ratio minimum) must hold as well. Effect: raise = the ratio check in 3rd/4th gear waits longer after a shift before it can run Evidence: ledger:E0766, ledger:E0806</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7D8" flags="0x0">
    <title>Shift Sol B Stuck On (P0757), 4th Gear - Converter Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest converter speed ratio at which the shift solenoid B stuck-on test (P0757) watches the transmission in 4th gear. Stock 0.5. The converter speed ratio here is the PCM&#x27;s own torque converter model estimate (turbine speed over engine speed, from engine speed and torque): 1.00 = coupled, low values = high slip. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test waits until the converter is closer to coupled Evidence: ledger:E0766, ledger:E0841, ledger:E0851</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7D9" flags="0x0">
    <title>Shift Sol Tests, 1st Gear Decision - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest driver throttle-area request at which the shift solenoid A performance test (P0751) and shift solenoid B performance test (P0756) can reach a pass or fail decision in 1st gear. Stock 25 %. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at a larger throttle request Evidence: ledger:E0766, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F618" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7DA" flags="0x0">
    <title>Shift Sol Tests, 1st Gear Decision - Torque Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest engine torque at which the shift solenoid A performance test (P0751) and shift solenoid B performance test (P0756) can reach a pass or fail decision in 1st gear. Stock 550 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: lower = the test stops running at a lower engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5FA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7DB" flags="0x0">
    <title>Shift Sol Tests, 1st Gear Decision - Torque Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest engine torque at which the shift solenoid A performance test (P0751) and shift solenoid B performance test (P0756) can reach a pass or fail decision in 1st gear. Stock 47 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at higher engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5DC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7DC" flags="0x0">
    <title>Shift Sol Tests, 1st Gear Decision - Converter Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest converter speed ratio at which the shift solenoid A performance test (P0751) and shift solenoid B performance test (P0756) can reach a pass or fail decision in 1st gear. Stock 0.5. The converter speed ratio here is the PCM&#x27;s own torque converter model estimate (turbine speed over engine speed, from engine speed and torque): 1.00 = coupled, low values = high slip. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test waits until the converter is closer to coupled Evidence: ledger:E0766, ledger:E0841, ledger:E0851</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7DD" flags="0x0">
    <title>Shift Sol Tests, 2nd Gear Decision - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest driver throttle-area request at which the shift solenoid A stuck-on test (P0752) and shift solenoid B performance test (P0756) can reach a pass or fail decision in 2nd gear. Stock 25 %. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at a larger throttle request Evidence: ledger:E0766, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F61A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7DE" flags="0x0">
    <title>Shift Sol Tests, 2nd Gear Decision - Torque Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest engine torque at which the shift solenoid A stuck-on test (P0752) and shift solenoid B performance test (P0756) can reach a pass or fail decision in 2nd gear. Stock 550 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: lower = the test stops running at a lower engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7DF" flags="0x0">
    <title>Shift Sol Tests, 2nd Gear Decision - Torque Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest engine torque at which the shift solenoid A stuck-on test (P0752) and shift solenoid B performance test (P0756) can reach a pass or fail decision in 2nd gear. Stock 47 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at higher engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5DE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7E0" flags="0x0">
    <title>Shift Sol Tests, 2nd Gear Decision - Converter Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest converter speed ratio at which the shift solenoid A stuck-on test (P0752) and shift solenoid B performance test (P0756) can reach a pass or fail decision in 2nd gear. Stock 0.5. The converter speed ratio here is the PCM&#x27;s own torque converter model estimate (turbine speed over engine speed, from engine speed and torque): 1.00 = coupled, low values = high slip. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test waits until the converter is closer to coupled Evidence: ledger:E0766, ledger:E0841, ledger:E0851</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7E1" flags="0x0">
    <title>Shift Sol Tests, 3rd Gear Decision - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest driver throttle-area request at which the shift solenoid A stuck-on test (P0752) and shift solenoid B stuck-on test (P0757) can reach a pass or fail decision in 3rd gear. Stock 25 %. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at a larger throttle request Evidence: ledger:E0766, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F61C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7E2" flags="0x0">
    <title>Shift Sol Tests, 3rd Gear Decision - Torque Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest engine torque at which the shift solenoid A stuck-on test (P0752) and shift solenoid B stuck-on test (P0757) can reach a pass or fail decision in 3rd gear. Stock 550 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: lower = the test stops running at a lower engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7E3" flags="0x0">
    <title>Shift Sol Tests, 3rd Gear Decision - Torque Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest engine torque at which the shift solenoid A stuck-on test (P0752) and shift solenoid B stuck-on test (P0757) can reach a pass or fail decision in 3rd gear. Stock 47 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at higher engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5E0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7E4" flags="0x0">
    <title>Shift Sol Tests, 3rd Gear Decision - Converter Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest converter speed ratio at which the shift solenoid A stuck-on test (P0752) and shift solenoid B stuck-on test (P0757) can reach a pass or fail decision in 3rd gear. Stock 0.5. The converter speed ratio here is the PCM&#x27;s own torque converter model estimate (turbine speed over engine speed, from engine speed and torque): 1.00 = coupled, low values = high slip. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test waits until the converter is closer to coupled Evidence: ledger:E0766, ledger:E0841, ledger:E0851</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7E5" flags="0x0">
    <title>Shift Sol Tests, 4th Gear Decision - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest driver throttle-area request at which the shift solenoid A performance test (P0751) and shift solenoid B stuck-on test (P0757) can reach a pass or fail decision in 4th gear. Stock 25 %. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at a larger throttle request Evidence: ledger:E0766, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F61E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7E6" flags="0x0">
    <title>Shift Sol Tests, 4th Gear Decision - Torque Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest engine torque at which the shift solenoid A performance test (P0751) and shift solenoid B stuck-on test (P0757) can reach a pass or fail decision in 4th gear. Stock 550 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: lower = the test stops running at a lower engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F600" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7E7" flags="0x0">
    <title>Shift Sol Tests, 4th Gear Decision - Torque Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest engine torque at which the shift solenoid A performance test (P0751) and shift solenoid B stuck-on test (P0757) can reach a pass or fail decision in 4th gear. Stock 47 Nm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at higher engine torque Evidence: ledger:E0766, ledger:E0806, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7E8" flags="0x0">
    <title>Shift Sol Tests, 4th Gear Decision - Converter Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest converter speed ratio at which the shift solenoid A performance test (P0751) and shift solenoid B stuck-on test (P0757) can reach a pass or fail decision in 4th gear. Stock 0.5. The converter speed ratio here is the PCM&#x27;s own torque converter model estimate (turbine speed over engine speed, from engine speed and torque): 1.00 = coupled, low values = high slip. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test waits until the converter is closer to coupled Evidence: ledger:E0766, ledger:E0807, ledger:E0841, ledger:E0851</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7E9" flags="0x0">
    <title>Pressure Switch Position Checks - 1st Gear Ratio Window Low (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Bottom of the 1st gear ratio window of the pressure switch position checks. Stock 3.000. It is read only by checks that are switched off on this truck (P1817, P1818, P1826 and an unused P1816 path), so it has no effect. Effect: no effect on this truck Evidence: ledger:E0767, ledger:E0813, ledger:E0910, ledger:E1101</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F868" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7EA" flags="0x0">
    <title>Pressure Switch Position Checks - 1st Gear Ratio Window High (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Top of the 1st gear ratio window of the pressure switch position checks. Stock 3.100. It is read only by checks that are switched off on this truck (P1817, P1818, P1826 and an unused P1816 path), so it has no effect. Effect: no effect on this truck Evidence: ledger:E0767, ledger:E0813, ledger:E0910, ledger:E1101</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F866" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7EB" flags="0x0">
    <title>Pressure Switch Position Checks - 2nd Gear Ratio Window Low (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Bottom of the 2nd gear ratio window of the pressure switch position checks. Stock 1.580. It is read only by checks that are switched off on this truck (P1817, P1818, P1826 and an unused P1816 path), so it has no effect. Effect: no effect on this truck Evidence: ledger:E0767, ledger:E0813, ledger:E0910, ledger:E1101</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F86C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7EC" flags="0x0">
    <title>Pressure Switch Position Checks - 2nd Gear Ratio Window High (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Top of the 2nd gear ratio window of the pressure switch position checks. Stock 1.680. It is read only by checks that are switched off on this truck (P1817, P1818, P1826 and an unused P1816 path), so it has no effect. Effect: no effect on this truck Evidence: ledger:E0767, ledger:E0813, ledger:E0910, ledger:E1101</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F86A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7ED" flags="0x0">
    <title>Pressure Switch Position Checks - 3rd Gear Ratio Window Low (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Bottom of the 3rd gear ratio window of the pressure switch position checks. Stock 0.900. It is read only by checks that are switched off on this truck (P1817, P1818, P1826 and an unused P1816 path), so it has no effect. Effect: no effect on this truck Evidence: ledger:E0767, ledger:E0813, ledger:E0910, ledger:E1101</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F870" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7EE" flags="0x0">
    <title>Pressure Switch Position Checks - 3rd Gear Ratio Window High (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Top of the 3rd gear ratio window of the pressure switch position checks. Stock 1.100. It is read only by checks that are switched off on this truck (P1817, P1818, P1826 and an unused P1816 path), so it has no effect. Effect: no effect on this truck Evidence: ledger:E0767, ledger:E0813, ledger:E0910, ledger:E1101</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F86E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7EF" flags="0x0">
    <title>Pressure Switch Position Checks - 4th Gear Ratio Window Low (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Bottom of the 4th gear ratio window of the pressure switch position checks. Stock 0.600. It is read only by checks that are switched off on this truck (P1817, P1818, P1826 and an unused P1816 path), so it has no effect. Effect: no effect on this truck Evidence: ledger:E0767, ledger:E0813, ledger:E0910, ledger:E1101</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F874" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7F0" flags="0x0">
    <title>Pressure Switch Position Checks - 4th Gear Ratio Window High (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Top of the 4th gear ratio window of the pressure switch position checks. Stock 0.790. It is read only by checks that are switched off on this truck (P1817, P1818, P1826 and an unused P1816 path), so it has no effect. Effect: no effect on this truck Evidence: ledger:E0767, ledger:E0813, ledger:E0910, ledger:E1101</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F872" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7F1" flags="0x0">
    <title>Pressure Switch Position Checks - 5th Ratio Window Low (unused)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Bottom end of the fifth ratio window of the pressure switch position checks (a ratio inside any of the five windows counts as in gear). Stock 0 to 0, so it only matches a ratio of 0. The checks are switched off on this truck (P1817, P1818, P1826). This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0767, ledger:E0807, ledger:E1264</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F878" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7F2" flags="0x0">
    <title>Pressure Switch Position Checks - 5th Ratio Window High (unused)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Top end of the fifth ratio window of the pressure switch position checks (a ratio inside any of the five windows counts as in gear). Stock 0 to 0, so it only matches a ratio of 0. The checks are switched off on this truck (P1817, P1818, P1826). This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0767, ledger:E0807, ledger:E1264</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F876" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7F3" flags="0x0">
    <title>P1815 Test - Engine Stopped Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1815 (engine started with the transmission range not reading park or neutral) check: engine speed at or below which the engine counts as stopped. Stock 50 rpm. The check follows one engine start: stopped, cranking, running. Effect: raise = higher speeds still count as stopped Evidence: ledger:E1100</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F8B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7F4" flags="0x0">
    <title>P1815 Test - Cranking Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1815 (engine started with the transmission range not reading park or neutral) check: lowest engine speed that counts as cranking. Stock 50 rpm. The check follows one engine start: stopped, cranking, running. Effect: raise = cranking is seen only at higher speed Evidence: ledger:E1100</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F8AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7F5" flags="0x0">
    <title>P1815 Test - Cranking Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1815 (engine started with the transmission range not reading park or neutral) check: highest engine speed that counts as cranking. Stock 610 rpm. The check follows one engine start: stopped, cranking, running. Effect: raise = higher speeds still count as cranking Evidence: ledger:E1100</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F8AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7F6" flags="0x0">
    <title>P1815 Test - Engine Running Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1815 (engine started with the transmission range not reading park or neutral) check: engine speed at or above which the engine counts as running and the range is judged. Stock 625 rpm. The check follows one engine start: stopped, cranking, running. Effect: raise = the range is judged only at higher engine speed Evidence: ledger:E1100</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F8AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7F7" flags="0x0">
    <title>P1815 Test - Run Condition, Output Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1815 (engine started with the transmission range not reading park or neutral) check: the check runs only with transmission output speed at or below this; above it the check ends for the key cycle without a result. Stock 250 rpm. Effect: raise = the check keeps running at higher output speed Evidence: ledger:E1100</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F8B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7F8" flags="0x0">
    <title>P1815 Test - Engine Stopped Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1815 (engine started with the transmission range not reading park or neutral) check: time the engine must read stopped before cranking can be seen. Stock 0.2 s. The check follows one engine start: stopped, cranking, running. Effect: raise = the engine must be seen stopped for longer Evidence: ledger:E1100</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F8B6" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7F9" flags="0x0">
    <title>P1815 Test - Cranking Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1815 (engine started with the transmission range not reading park or neutral) check: time the engine must read cranking. Stock 0.00625 s: met on the first 25 ms sample. The check follows one engine start: stopped, cranking, running. Effect: raise = cranking must be seen for longer Evidence: ledger:E1100</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F8B7" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7FA" flags="0x0">
    <title>P1815 Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1815 (engine started with the transmission range not reading park or neutral) check: time the range must read park / neutral once the engine runs to pass. Stock 0.00625 s: met on the first 25 ms sample. Effect: raise = the check takes longer to pass Evidence: ledger:E1100</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F8BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7FB" flags="0x0">
    <title>P1816 Test - Run Condition, Engine Torque Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1816 (fluid pressure switch reads park / neutral in 4th gear) check: the check runs (4th gear, converter clutch applied) only with engine torque at or above this. Stock 65 Nm. Effect: raise = the check needs more engine torque Evidence: ledger:E0767, ledger:E0806, ledger:E1101</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F88E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7FC" flags="0x0">
    <title>P1816 Test - Run Condition, Engine Torque Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1816 (fluid pressure switch reads park / neutral in 4th gear) check: the check runs (4th gear, converter clutch applied) only with engine torque at or below this. Stock 550 Nm. Effect: lower = the check stops at lower torque Evidence: ledger:E0767, ledger:E0972, ledger:E1101</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F890" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7FD" flags="0x0">
    <title>P1816 Test - Run Condition, Throttle Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1816 (fluid pressure switch reads park / neutral in 4th gear) check: the check runs (4th gear, converter clutch applied) only with driver throttle at or above this. Stock 10 %. Effect: raise = the check needs more throttle Evidence: ledger:E0767, ledger:E0972, ledger:E1101</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F88C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7FE" flags="0x0">
    <title>Garage Shift Learning - Maximum First Phase Time Correction (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learning stops while the learned first phase time correction plus the new step is at or above this (stock 0 s: learning never runs). Garage shift learning: after a garage shift the measured time to the third phase (times the time factor) is compared with the first phase time limit; the step from this curve is added to the learned first phase time correction. Learning never runs on the stock calibration: the maximum correction is 0 s and the fluid temperature and RPM windows are closed (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1500</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x37D9C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7FF" flags="0x0">
    <title>Input Torque Limit - Arm Above Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The engine speed flag sets above this; it clears below the disarm speed and holds in between. Stock 8000 rpm. The transmission input torque limit cuts engine torque to the limit only while armed (engine speed and throttle flags both set, no shift). On this truck the throttle flag can never set (stock 100 %), so the limit never arms and this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0773, ledger:E1175, ledger:E1178, ledger:E1490</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3EC08" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x800" flags="0x0">
    <title>Input Torque Limit - Disarm Below Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The engine speed flag clears below this. Stock 7000 rpm. The transmission input torque limit cuts engine torque to the limit only while armed (engine speed and throttle flags both set, no shift). On this truck the throttle flag can never set (stock 100 %), so the limit never arms and this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0773, ledger:E1175, ledger:E1178, ledger:E1490</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3EC06" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x801" flags="0x0">
    <title>Input Torque Limit - Disarm Below Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The throttle flag clears below this. Stock 99.0 %. The transmission input torque limit cuts engine torque to the limit only while armed (engine speed and throttle flags both set, no shift). On this truck the throttle flag can never set (stock 100 %), so the limit never arms and this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0773, ledger:E1175, ledger:E1178, ledger:E1490</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3EC0A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x802" flags="0x0">
    <title>Input Torque Limit - Arm Above Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The throttle flag sets above this; it clears below the disarm throttle and holds in between. Stock 100 % (can never be exceeded). The transmission input torque limit cuts engine torque to the limit only while armed (engine speed and throttle flags both set, no shift). On this truck the throttle flag can never set (stock 100 %), so the limit never arms and this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0773, ledger:E1175, ledger:E1178, ledger:E1490</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3EC0C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x803" flags="0x0">
    <title>Transmission Input Torque Limit in Reverse, 4WD-Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Limit on transmission input (turbine) torque in Reverse, used in 4WD-Low (transfer case range) in place of the per-gear limit curves. Stock 827 Nm. The limit never arms on this calibration (its arming thresholds are out of reach). Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0773, ledger:E1175, ledger:E1178, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3EC10" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x804" flags="0x0">
    <title>Transmission Input Torque Limit in Reverse, base</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Limit on transmission input (turbine) torque in Reverse, used outside 4WD-Low and 4WD-High in place of the per-gear limit curves. Stock 827 Nm. The limit never arms on this calibration (its arming thresholds are out of reach). Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0773, ledger:E1175, ledger:E1178, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3EC0E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x805" flags="0x0">
    <title>Converter Model - Engine Rotating Inertia</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rotating inertia of the engine side (crankshaft, flywheel, converter impeller) in the converter model. While the engine speeds up, inertia x engine acceleration is taken off engine torque to give the torque through the converter. Stock 0.205 kg m^2. Part of the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: raise = the model credits less torque to the converter while the engine accelerates Evidence: ledger:E0774, ledger:E1539</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kg m^2</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.023776</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/64013"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x806" flags="0x0">
    <title>Converter Model - Engine Torque Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new engine torque sample taken into the converter model&#x27;s filtered torque. Stock 0.50. Part of the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: lower = smoother but slower torque in the model Evidence: ledger:E0774, ledger:E1419</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x807" flags="0x0">
    <title>Converter Model - Clutch Pressure Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new converter clutch pressure value (while the clutch is applied) taken into the model&#x27;s filtered clutch pressure. Stock 0.15. Part of the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: lower = the model&#x27;s clutch torque reacts more slowly Evidence: ledger:E0774, ledger:E1481</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x808" flags="0x0">
    <title>Converter Model - Clutch Pressure Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter clutch pressure below which the model counts no torque through the clutch. Stock 0 kPa. Part of the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: raise = the model credits the clutch with torque only at higher pressure Evidence: ledger:E0774, ledger:E1481</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9E0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x809" flags="0x0">
    <title>Converter Model - Clutch Torque per Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque the model takes through the converter clutch per kPa of clutch pressure above the offset; that torque is removed from the converter torque. Stock 8 Nm per kPa. Part of the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: raise = the model puts more torque through the clutch Evidence: ledger:E0774, ledger:E1481</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm/kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x80A" flags="0x0">
    <title>Converter Model - Capacity Cold Fluid Adder, Temperature Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fluid temperature at or below which the cold fluid capacity adder is at its full value. Stock -40 C. Part of the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: raise = full adder up to warmer fluid Evidence: ledger:E0774, ledger:E1419</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x80B" flags="0x0">
    <title>Converter Model - Capacity Cold Fluid Adder, Temperature High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fluid temperature at or above which the cold fluid capacity adder is 0. Stock 20 C. Part of the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: raise = the cold adder lasts to warmer fluid Evidence: ledger:E0774, ledger:E1419</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x80C" flags="0x0">
    <title>Converter Model - Capacity Cold Fluid Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter capacity factor added with cold transmission fluid: full value at or below the low fluid temperature, fading to 0 at the high one. Stock 15 rpm / sqrt(Nm). Part of the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: raise = the model treats the converter as looser when cold Evidence: ledger:E0774, ledger:E1419</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9DA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm/sqrt(Nm)</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x80D" flags="0x0">
    <title>Converter Model - Slip Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new expected converter slip value taken into the model&#x27;s filtered slip. Stock 0.20. Part of the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: lower = smoother but slower modelled slip Evidence: ledger:E0774, ledger:E1419</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x80E" flags="0x0">
    <title>Converter Capacity Learn - Lowest Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter capacity learn: learning runs only in this gear or higher (0 = 1st, 1 = 2nd). Stock 1. The learned offset corrects the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: raise = learning only in higher gears Evidence: ledger:E0774, ledger:E1418</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gear index</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x80F" flags="0x0">
    <title>Converter Capacity Learn - Engine Torque Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter capacity learn: learning runs only with filtered engine torque at or above this. Stock 135 Nm. The learned offset corrects the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: raise = learning only at higher torque Evidence: ledger:E0774, ledger:E1418</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x810" flags="0x0">
    <title>Converter Capacity Learn - Engine Torque Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter capacity learn: learning runs only with filtered engine torque at or below this. Stock 320 Nm. The learned offset corrects the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: lower = learning only at lower torque Evidence: ledger:E0774, ledger:E1418</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x811" flags="0x0">
    <title>Converter Capacity Learn - Speed Ratio Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter capacity learn: learning runs only with the measured and the expected converter speed ratio (turbine over engine) at or above this. Stock 0.10. The learned offset corrects the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: raise = learning only closer to coupling Evidence: ledger:E0774, ledger:E0859, ledger:E1418</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9D4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x812" flags="0x0">
    <title>Converter Capacity Learn - Fluid Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter capacity learn: learning runs only with transmission fluid at or above this. Stock 25 C. The learned offset corrects the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: raise = learning only with warmer fluid Evidence: ledger:E0774, ledger:E1418</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x813" flags="0x0">
    <title>Converter Capacity Learn - Ratio High Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter capacity learn: an estimated gear ratio above the gear ratio times this counts toward lowering the learned offset. Stock 1.030. The learned offset corrects the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: raise = a larger ratio error is needed before learning down Evidence: ledger:E0774, ledger:E1418</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x814" flags="0x0">
    <title>Converter Capacity Learn - Ratio Low Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter capacity learn: an estimated gear ratio below the gear ratio times this counts toward raising the learned offset. Stock 0.970. The learned offset corrects the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: lower = a larger ratio error is needed before learning up Evidence: ledger:E0774, ledger:E1418</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x815" flags="0x0">
    <title>Converter Capacity Learn - Count to Step Up</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter capacity learn: the learn counter moves 25 per 25 ms pass with the ratio low; below this the learned offset steps up by 1 rpm / sqrt(Nm). Stock -1024. The learned offset corrects the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: closer to 0 = faster learning up Evidence: ledger:E0774, ledger:E1418</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>-32768.000000</min>
    <max>32767.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x816" flags="0x0">
    <title>Converter Capacity Learn - Count to Step Down</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter capacity learn: the learn counter moves 25 per 25 ms pass with the ratio high; above this the learned offset steps down by 1 rpm / sqrt(Nm). Stock 1024. The learned offset corrects the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: closer to 0 = faster learning down Evidence: ledger:E0774, ledger:E1418</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>-32768.000000</min>
    <max>32767.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x817" flags="0x0">
    <title>Converter Capacity Learn - Offset Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter capacity learn: lowest learned capacity factor offset. Stock -10 rpm / sqrt(Nm). The learned offset corrects the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: raise = less downward correction allowed Evidence: ledger:E0774, ledger:E1418</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9D8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm/sqrt(Nm)</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x818" flags="0x0">
    <title>Converter Capacity Learn - Offset Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter capacity learn: highest learned capacity factor offset. Stock 10 rpm / sqrt(Nm). The learned offset corrects the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: lower = less upward correction allowed Evidence: ledger:E0774, ledger:E1418</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9D6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm/sqrt(Nm)</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x819" flags="0x0">
    <title>Converter Model Alternate Estimate - Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new alternate estimate value taken into the filtered value; 0 = no smoothing. Stock 0.21. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0774, ledger:E1491</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E994" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x81A" flags="0x0">
    <title>P2764 Fail - Fault Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2764 (converter clutch pulse width solenoid circuit check at low duty): fault samples inside the window that set the code. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the fault must be present for more of the window Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F688" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x81B" flags="0x0">
    <title>P2764 Pass - Good Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2764 (converter clutch pulse width solenoid circuit check at low duty): good samples inside the window that pass the check. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the circuit must read good for more of the window Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F689" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x81C" flags="0x0">
    <title>P2764 Test - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2764 (converter clutch pulse width solenoid circuit check at low duty): length of the sample window. Stock 5 s. Keep it at or above the fail and pass times, or the check can never report. Effect: raise = fault samples may be spread over a longer time Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F68A" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x81D" flags="0x0">
    <title>P2764 Test - Commanded Duty Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2764 (converter clutch pulse width solenoid circuit check at low duty): the circuit is sampled (fault and good samples) only with the commanded solenoid duty at or below this. Stock 10 %. Effect: raise = the circuit is also checked at higher duty Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F68C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x81E" flags="0x0">
    <title>P0741 Test - Run Condition, Speed Ratio Window 1 Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0741 (converter clutch stuck off) test: bottom of the first input / output speed ratio window in which the test may run. Stock 1.570 (around 2nd gear, 1.625). Effect: lower = the window reaches lower ratios Evidence: ledger:E0777, ledger:E0910, ledger:E0916, ledger:E1095</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F6BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x81F" flags="0x0">
    <title>P0741 Test - Run Condition, Speed Ratio Window 1 Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0741 (converter clutch stuck off) test: top of the first input / output speed ratio window in which the test may run. Stock 1.680 (around 2nd gear, 1.625). Effect: raise = the window reaches higher ratios Evidence: ledger:E0777, ledger:E0910, ledger:E0916, ledger:E1095</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F6B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x820" flags="0x0">
    <title>P0741 Test - Run Condition, Speed Ratio Window 2 Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0741 (converter clutch stuck off) test: bottom of the second input / output speed ratio window in which the test may run. Stock 0.900 (around 3rd gear, 1.00). Effect: lower = the window reaches lower ratios Evidence: ledger:E0777, ledger:E0910, ledger:E0916, ledger:E1095</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F6BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x821" flags="0x0">
    <title>P0741 Test - Run Condition, Speed Ratio Window 2 Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0741 (converter clutch stuck off) test: top of the second input / output speed ratio window in which the test may run. Stock 1.100 (around 3rd gear, 1.00). Effect: raise = the window reaches higher ratios Evidence: ledger:E0777, ledger:E0910, ledger:E0916, ledger:E1095</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F6BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x822" flags="0x0">
    <title>P0741 Test - Run Condition, Speed Ratio Window 3 Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0741 (converter clutch stuck off) test: bottom of the third input / output speed ratio window in which the test may run. Stock 0.900: it lies inside window 2, so it adds nothing until it is moved. Effect: lower = the window reaches lower ratios Evidence: ledger:E0777, ledger:E0910, ledger:E0916, ledger:E1095</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F6C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x823" flags="0x0">
    <title>P0741 Test - Run Condition, Speed Ratio Window 3 Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0741 (converter clutch stuck off) test: top of the third input / output speed ratio window in which the test may run. Stock 1.090: it lies inside window 2, so it adds nothing until it is moved. Effect: raise = the window reaches higher ratios Evidence: ledger:E0777, ledger:E0910, ledger:E0916, ledger:E1095</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F6C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x824" flags="0x0">
    <title>P0741 Test - Run Condition, Speed Ratio Window 4 Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0741 (converter clutch stuck off) test: bottom of the fourth input / output speed ratio window in which the test may run. Stock 0 with a maximum of 0: the window is empty. Effect: see the window 4 maximum Evidence: ledger:E1095</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F6C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x825" flags="0x0">
    <title>P0741 Test - Run Condition, Speed Ratio Window 4 Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0741 (converter clutch stuck off) test: top of the fourth input / output speed ratio window in which the test may run. Stock 0 with a minimum of 0: the window is empty, so the test runs in 2nd and 3rd gear only (windows 1 to 3). Set the pair around 0.70 to let it run in 4th gear. Effect: raise (with the minimum) = the test also runs at that ratio Evidence: ledger:E1095</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F6C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x826" flags="0x0">
    <title>P1887 Test - Fluid Temperature Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1887 (converter clutch release switch check): the check arms only with transmission fluid at or above this. Stock 199 C. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0777, ledger:E1403</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F678" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x827" flags="0x0">
    <title>P1887 Test - Fluid Temperature Maximum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1887 (converter clutch release switch check): the check arms only with transmission fluid at or below this. Stock 200 C. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0777, ledger:E1403</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F67A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x828" flags="0x0">
    <title>P0719 Test - Pull-Away Time Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: longest time from the low speed to the high speed that counts as a pull-away event. Stock 12.5 s. A pull-away event is: from the low speed up to the high speed inside the time window, then the hold time above the high speed. Effect: raise = slower pull-aways also count Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F640" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x829" flags="0x0">
    <title>P0719 Test - Pull-Away Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: shortest time from the low speed to the high speed that counts as a pull-away event. Stock 2.5 s. A pull-away event is: from the low speed up to the high speed inside the time window, then the hold time above the high speed. Effect: raise = quick pull-aways no longer count Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F641" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x82A" flags="0x0">
    <title>P0719 Test - Time Above High Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: time the truck must stay at or above the high speed to complete a pull-away event. Stock 7 s. A pull-away event is: from the low speed up to the high speed inside the time window, then the hold time above the high speed. Effect: raise = each event needs longer at speed Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F642" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x82B" flags="0x0">
    <title>P0719 Fail - Brake Input On Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: time the brake input must read on without a break before the code can set (together with the pull-away event count). Stock 900 s. Effect: raise = the input must stay on longer Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F644" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x82C" flags="0x0">
    <title>P0719 Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: time the brake input must read off to pass the check. Stock 2 s. Effect: raise = the check takes longer to pass Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F646" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x82D" flags="0x0">
    <title>P0724 Test - Time Above High Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0724 (brake switch input stuck off) check: time the truck must stay at or above the high speed before a stop event can start. Stock 7 s. A stop event is: the hold time above the high speed, then down to the low speed inside the time window. Effect: raise = each event needs longer at speed first Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F647" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x82E" flags="0x0">
    <title>P0724 Test - Stop Time Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0724 (brake switch input stuck off) check: longest time from the high speed down to the low speed that counts as a stop event. Stock 12.5 s. A stop event is: the hold time above the high speed, then down to the low speed inside the time window. Effect: raise = slower stops also count Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F648" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x82F" flags="0x0">
    <title>P0724 Test - Stop Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0724 (brake switch input stuck off) check: shortest time from the high speed down to the low speed that counts as a stop event. Stock 2.5 s. A stop event is: the hold time above the high speed, then down to the low speed inside the time window. Effect: raise = quick stops no longer count Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F649" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x830" flags="0x0">
    <title>P0724 Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0724 (brake switch input stuck off) check: time the brake input must read on to pass the check. Stock 2 s. Effect: raise = the check takes longer to pass Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F64A" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x831" flags="0x0">
    <title>P0719 Test - Pull-Away Low Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: a pull-away event starts from at or below this speed. Stock 8 km/h. A pull-away event is: from the low speed up to the high speed inside the time window, then the hold time above the high speed. Effect: raise = events can start from a higher speed Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F64C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x832" flags="0x0">
    <title>P0719 Test - Pull-Away High Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: speed the truck must reach to end the acceleration part of a pull-away event. Stock 32 km/h. A pull-away event is: from the low speed up to the high speed inside the time window, then the hold time above the high speed. Effect: raise = events need a higher speed Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F64E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x833" flags="0x0">
    <title>P0724 Test - Stop High Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0724 (brake switch input stuck off) check: a stop event starts from at or above this speed. Stock 32 km/h. A stop event is: the hold time above the high speed, then down to the low speed inside the time window. Effect: raise = events need a higher starting speed Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F650" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x834" flags="0x0">
    <title>P0724 Test - Stop Low Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0724 (brake switch input stuck off) check: speed the truck must slow to, to complete a stop event. Stock 8 km/h. A stop event is: the hold time above the high speed, then down to the low speed inside the time window. Effect: raise = events complete at a higher speed Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F652" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x835" flags="0x0">
    <title>P0724 - Stops to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0724 (brake switch input stuck off) check: number of stop events with the brake input reading off all the time that sets the code. Stock 8. A stop event is: the hold time above the high speed, then down to the low speed inside the time window. Effect: raise = more stops are needed to set the code Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F654" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x836" flags="0x0">
    <title>P0719 - Pull-Aways to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: number of pull-away events with the brake input reading on all the time that is needed (with the on time) to set the code. Stock 8. A pull-away event is: from the low speed up to the high speed inside the time window, then the hold time above the high speed. Effect: raise = more pull-aways are needed to set the code Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F655" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x837" flags="0x0">
    <title>P2770 Fail - Fault Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2770 (converter clutch on/off solenoid circuit check while commanded on): fault samples inside the window that set the code. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the fault must be present for more of the window Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F65C" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x838" flags="0x0">
    <title>P2770 Pass - Good Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2770 (converter clutch on/off solenoid circuit check while commanded on): good samples inside the window that pass the check. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the circuit must read good for more of the window Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F65D" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x839" flags="0x0">
    <title>P2770 Test - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2770 (converter clutch on/off solenoid circuit check while commanded on): length of the sample window. Stock 5 s. Keep it at or above the fail and pass times, or the check can never report. Effect: raise = fault samples may be spread over a longer time Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F65E" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x83A" flags="0x0">
    <title>P2769 Fail - Fault Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2769 (converter clutch on/off solenoid circuit check while commanded off): fault samples inside the window that set the code. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the fault must be present for more of the window Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F662" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x83B" flags="0x0">
    <title>P2769 Pass - Good Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2769 (converter clutch on/off solenoid circuit check while commanded off): good samples inside the window that pass the check. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the circuit must read good for more of the window Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F663" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x83C" flags="0x0">
    <title>P2769 Test - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2769 (converter clutch on/off solenoid circuit check while commanded off): length of the sample window. Stock 5 s. Keep it at or above the fail and pass times, or the check can never report. Effect: raise = fault samples may be spread over a longer time Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F664" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x83D" flags="0x0">
    <title>P1887 Test - Converter Slip Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1887 (converter clutch release switch check): the check arms only with converter slip at or above this. Stock 0 rpm. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0777, ledger:E1403</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F66A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x83E" flags="0x0">
    <title>P1887 Test - Converter Slip Maximum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1887 (converter clutch release switch check): the check arms only with converter slip at or below this. Stock 0 rpm. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0777, ledger:E1403</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F66C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x83F" flags="0x0">
    <title>P1887 Test - TCC Pressure Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1887 (converter clutch release switch check): the check arms only with commanded converter clutch pressure at or above this. Stock 0 kPa. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0777, ledger:E1481</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F66E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x840" flags="0x0">
    <title>P1887 Test - TCC Pressure Maximum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1887 (converter clutch release switch check): the check arms only with commanded converter clutch pressure at or below this. Stock 0 kPa. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0777, ledger:E1481</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F670" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x841" flags="0x0">
    <title>P1887 Test - Engine Torque Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1887 (converter clutch release switch check): lowest engine torque at which the check arms. The check is not used on this truck (switched off, its windows are closed and the code is disabled), so this value has no effect. Stock 8190 Nm. Effect: no effect on this truck Evidence: ledger:E0777, ledger:E0806, ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F672" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x842" flags="0x0">
    <title>P1887 Test - Engine Torque Maximum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1887 (converter clutch release switch check): the check arms only with engine torque at or below this. Stock 8191.9 Nm. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0777, ledger:E1403</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F674" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x843" flags="0x30">
    <title>4-Lo Full-Throttle Shift - Upshift Speed by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission-side speed at which the transmission shifts up out of each gear (1st, 2nd, 3rd; the 4th-gear value is never used). Stock 20 / 70 / 170 km/h, about 5 / 17 / 42 km/h of road speed. The upshift also needs engine speed at the Upshift Minimum Engine Speed. Used in 4-Lo while pedal demand is above the 4-Lo high pedal set point (stock 56 %); in that state this rule decides the gear ahead of the 4-Lo shift schedule, and the range selector still caps the highest gear. In 4-Lo the transmission&#x27;s speed reading is 4.03 times road speed (it is worked out from transmission output speed with the high-range ratio), so...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39574" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x844" flags="0x30">
    <title>4-Lo Full-Throttle Shift - Downshift Speed by Target Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission-side speed below which the transmission shifts down into each gear (1st, 2nd, 3rd). Stock 17.5 / 65 / 160 km/h, about 4 / 16 / 40 km/h of road speed. Used in 4-Lo while pedal demand is above the 4-Lo high pedal set point (stock 56 %); in that state this rule decides the gear ahead of the 4-Lo shift schedule, and the range selector still caps the highest gear. In 4-Lo the transmission&#x27;s speed reading is 4.03 times road speed (it is worked out from transmission output speed with the high-range ratio), so a value of 40 km/h here acts at about 10 km/h on the road. Effect: raise a gear&#x27;s value = the downshif...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3957C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x845" flags="0x30">
    <title>4-Lo Full-Throttle Shift - Upshift Minimum Engine Speed by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed that must also be reached before the transmission shifts up out of each gear. Stock 4000 / 5800 / 5800 rpm out of 1st / 2nd / 3rd; the 4th-gear value (8192 rpm) is never used. Used in 4-Lo while pedal demand is above the 4-Lo high pedal set point (stock 56 %); in that state this rule decides the gear ahead of the 4-Lo shift schedule, and the range selector still caps the highest gear. Effect: raise a gear&#x27;s value = that upshift waits for higher engine speed Evidence: ledger:E0778, ledger:E0812, ledger:E0847</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39582" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x846" flags="0x30">
    <title>3rd Gear Range Shift Speed Correction - Upshift, Normal</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Speed added to the scheduled upshift speed, by throttle, while the shifter is in the range limited to 3rd gear and the PCM is in its normal shift mode. A negative value lowers the shift speed. Stock: the 3-4 row adds 20 to 73 mph, on top of a 3rd-max schedule that already never upshifts to 4th; the other rows are 0. Effect: raise = that upshift happens at a higher road speed in the 3rd-gear range Evidence: ledger:E0778, ledger:E1027</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2 upshift" />
      <LABEL index="1" value="2-3 upshift" />
      <LABEL index="2" value="3-4 upshift" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38B56" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>-159.071025</min>
      <max>159.066171</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x847" flags="0x30">
    <title>3rd Gear Range Shift Speed Correction - Upshift, 4-Lo</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Speed added to the scheduled upshift speed, by throttle, while the shifter is in the range limited to 3rd gear and the PCM is in its 4-Lo shift mode. A negative value lowers the shift speed. Stock all 0. Effect: raise = that upshift happens at a higher road speed in the 3rd-gear range Evidence: ledger:E0778, ledger:E1027</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2 upshift" />
      <LABEL index="1" value="2-3 upshift" />
      <LABEL index="2" value="3-4 upshift" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38BC6" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>-159.071025</min>
      <max>159.066171</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x848" flags="0x30">
    <title>3rd Gear Range Shift Speed Correction - Upshift, Cruise</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Speed added to the scheduled upshift speed, by throttle, while the shifter is in the range limited to 3rd gear and the PCM is in its cruise shift mode. A negative value lowers the shift speed. Stock all 0. Effect: raise = that upshift happens at a higher road speed in the 3rd-gear range Evidence: ledger:E0778, ledger:E1027</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2 upshift" />
      <LABEL index="1" value="2-3 upshift" />
      <LABEL index="2" value="3-4 upshift" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38C36" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>-159.071025</min>
      <max>159.066171</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x849" flags="0x30">
    <title>3rd Gear Range Shift Speed Correction - Downshift, Normal</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Speed added to the scheduled downshift speed, by throttle, while the shifter is in the range limited to 3rd gear and the PCM is in its normal shift mode. A negative value lowers the shift speed. Stock all 0. Effect: raise = that downshift happens at a higher road speed in the 3rd-gear range Evidence: ledger:E0778, ledger:E1027</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2-1 downshift" />
      <LABEL index="1" value="3-2 downshift" />
      <LABEL index="2" value="4-3 downshift" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38CA6" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>-159.071025</min>
      <max>159.066171</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x84A" flags="0x30">
    <title>3rd Gear Range Shift Speed Correction - Downshift, Cruise</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Speed added to the scheduled downshift speed, by throttle, while the shifter is in the range limited to 3rd gear and the PCM is in its cruise shift mode. A negative value lowers the shift speed. Stock all 0. Effect: raise = that downshift happens at a higher road speed in the 3rd-gear range Evidence: ledger:E0778, ledger:E1027</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2-1 downshift" />
      <LABEL index="1" value="3-2 downshift" />
      <LABEL index="2" value="4-3 downshift" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38D16" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>-159.071025</min>
      <max>159.066171</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x84B" flags="0x30">
    <title>3rd Gear Range Shift Speed Correction - Downshift, 4-Lo</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Speed added to the scheduled downshift speed, by throttle, while the shifter is in the range limited to 3rd gear and the PCM is in its 4-Lo shift mode. A negative value lowers the shift speed. Stock all 0. Effect: raise = that downshift happens at a higher road speed in the 3rd-gear range Evidence: ledger:E0778, ledger:E1027</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2-1 downshift" />
      <LABEL index="1" value="3-2 downshift" />
      <LABEL index="2" value="4-3 downshift" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38D86" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>-159.071025</min>
      <max>159.066171</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x84C" flags="0x0">
    <title>Road Load Model - Score Sum Weight A (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of term A in the score sum. Part of the road load model&#x27;s score check, which lowers the top gear cap when a score term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1536</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3847C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x84D" flags="0x0">
    <title>Road Load Model - Score Sum Weight B (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of term B in the score sum. Part of the road load model&#x27;s score check, which lowers the top gear cap when a score term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1536</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3847E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x84E" flags="0x0">
    <title>Road Load Model - Release Sum Weight A (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of term A in the release sum. Part of the road load model&#x27;s release check, which raises the top gear cap again by one gear when a release term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1533</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38478" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x84F" flags="0x0">
    <title>Road Load Model - Release Sum Weight C (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of term C in the release sum. Part of the road load model&#x27;s release check, which raises the top gear cap again by one gear when a release term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1533</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3847A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x850" flags="0x0">
    <title>Road Load Model - Climb Index Min Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The grade force term is only used above this speed. Also used by the model&#x27;s second load index. Part of the road load model&#x27;s climb index: (grade force term minus torque term) times speed divided by the truck&#x27;s weight, an equivalent climb rate, accumulated over time; a high index lowers the top gear cap. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1510</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38486" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x851" flags="0x0">
    <title>Road Load Model - Vehicle Mass (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle mass used by the road load model for mass times acceleration, rolling resistance and weight on grade. Stock 0. Part of the road load model the shift sequencing uses to estimate grade and road load. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1485</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kg</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x852" flags="0x0">
    <title>Road Load Model - Grade Index Retention (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the previous grade index kept each update (0 = no memory). Part of the road load model&#x27;s grade index: the estimated grade force times speed divided by the truck&#x27;s weight, an equivalent climb rate, accumulated over time; a high index lowers the top gear cap. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1520</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38470" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x853" flags="0x0">
    <title>Road Load Model - Grade Index Decay Step, High Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Removed from a positive grade index each update while speed is at or above the Climb Index Min Speed. Part of the road load model&#x27;s grade index: the estimated grade force times speed divided by the truck&#x27;s weight, an equivalent climb rate, accumulated over time; a high index lowers the top gear cap. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1520</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3846C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>m/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>159.997559</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/409.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x854" flags="0x0">
    <title>Road Load Model - Climb Index Max (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest value of the climb index. Also used by the model&#x27;s second load index. Part of the road load model&#x27;s climb index: (grade force term minus torque term) times speed divided by the truck&#x27;s weight, an equivalent climb rate, accumulated over time; a high index lowers the top gear cap. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1510</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3846A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>m/s</units>
    <decimalpl>2</decimalpl>
    <min>-1280.000000</min>
    <max>1279.960938</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/25.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x855" flags="0x0">
    <title>Road Load Model - Climb Index Torque Term Min Slip (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The climb index torque term is only used while torque converter slip is above this. Part of the road load model&#x27;s climb index: (grade force term minus this torque term) times speed divided by the truck&#x27;s weight, an equivalent climb rate, accumulated over time; a high index lowers the top gear cap. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1524</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38458" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-32768.000000</min>
    <max>32767.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x856" flags="0x0">
    <title>Road Load Model - Climb Index Retention (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the previous climb index kept each update (0 = no memory). Part of the road load model&#x27;s climb index: (grade force term minus torque term) times speed divided by the truck&#x27;s weight, an equivalent climb rate, accumulated over time; a high index lowers the top gear cap. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1510</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38476" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x857" flags="0x0">
    <title>Road Load Model - Climb Index Decay Switch Level (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or above this climb index the high decay step applies, below it the low one. Part of the road load model&#x27;s climb index: (grade force term minus torque term) times speed divided by the truck&#x27;s weight, an equivalent climb rate, accumulated over time; a high index lowers the top gear cap. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1510</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38466" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>m/s</units>
    <decimalpl>2</decimalpl>
    <min>-1280.000000</min>
    <max>1279.960938</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/25.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x858" flags="0x0">
    <title>Road Load Model - Climb Index Decay Step, High (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Removed from a positive climb index each update while it is at or above the Decay Switch Level. Part of the road load model&#x27;s climb index: (grade force term minus torque term) times speed divided by the truck&#x27;s weight, an equivalent climb rate, accumulated over time; a high index lowers the top gear cap. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1510</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38464" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>m/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>159.997559</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/409.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x859" flags="0x0">
    <title>Road Load Model - Climb Index Decay Step, Low (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Removed from a positive climb index each update while it is below the Decay Switch Level. Part of the road load model&#x27;s climb index: (grade force term minus torque term) times speed divided by the truck&#x27;s weight, an equivalent climb rate, accumulated over time; a high index lowers the top gear cap. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1510</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38468" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>m/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>159.997559</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/409.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x85A" flags="0x0">
    <title>4th Upshift - Minimum Time Since the 2-3 Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. No 3-4 upshift until this long after the 2-3 shift was commanded (stock 1.5 s). Upshift minimum time in gear: when the shift schedule asks for that gear too soon, the transmission stays in the gear below until the time has passed. Effect: raise = holds 3rd longer before the 3-4 upshift; lower = quicker 3-4 upshift Evidence: ledger:E1433</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DE4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x85B" flags="0x0">
    <title>Mass Estimator - Maximum Acceleration</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Estimation runs only with vehicle acceleration below this. Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>m/s^2</units>
    <decimalpl>3</decimalpl>
    <min>-64.000000</min>
    <max>63.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x85C" flags="0x0">
    <title>Mass Estimator - Minimum Acceleration</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Estimation runs only with vehicle acceleration above this. Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>m/s^2</units>
    <decimalpl>3</decimalpl>
    <min>-64.000000</min>
    <max>63.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x85D" flags="0x0">
    <title>Mass Estimator - Maximum Axle Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The mass estimator runs only below this axle torque (steady value; while torque is changing the change also counts against it, so fast torque changes pause the estimate). Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1490</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-10922.666667</min>
    <max>10922.333333</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/3"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x85E" flags="0x0">
    <title>Mass Estimator - Maximum Wheel to Output Speed Mismatch</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Estimation pauses while the non-driven wheel speed and the transmission output speed differ by this or more (wheel slip). Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x85F" flags="0x0">
    <title>P0716 Test - Arming Input Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0716 (input speed sensor sudden drop): the check arms only after input speed has been above this. Stock 0 rpm. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0783, ledger:E1402</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F808" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x860" flags="0x0">
    <title>P0716 Test - Arming Time Above Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0716 (input speed sensor sudden drop): time above the arming input speed before the check arms. Stock 409.6 s. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0783, ledger:E1402</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F810" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x861" flags="0x0">
    <title>P0716 Test - Arming Rise Maximum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0716 (input speed sensor sudden drop): a rise of input speed of this much or more between samples restarts the arming time. Stock 0 rpm. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0783, ledger:E1402</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F80A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x862" flags="0x0">
    <title>P0716 Test - Arming Time Without Rise (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0716 (input speed sensor sudden drop): time without a large rise of input speed before the check arms. Stock 409.6 s. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0783, ledger:E1402</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F812" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x863" flags="0x0">
    <title>P0716 Pass - Input Speed Drop Maximum (inactive) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0716 input speed sensor signal drop check: largest drop of the input speed between two samples that still counts as good (stock 0). The check is switched off on this truck. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (switched off on this truck) Evidence: ledger:E0783, ledger:E0806, ledger:E0899, ledger:E1102</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F802" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x864" flags="0x0">
    <title>P0716 Pass - Input Speed Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0716 (input speed sensor sudden drop): the pass time runs only with input speed above this. Stock 0 rpm. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0783, ledger:E1402</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F806" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x865" flags="0x0">
    <title>P0716 Pass - Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0716 (input speed sensor sudden drop): time of good signal that passes the check. Stock 409.6 s. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0783, ledger:E1402</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F80C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x866" flags="0x0">
    <title>P0716 Fail - Vehicle Speed Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0716 (input speed sensor sudden drop): a speed drop counts as a fault only at or above this vehicle speed. Stock 0 km/h. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0783, ledger:E1402</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x867" flags="0x0">
    <title>P0716 Fail - Engine Torque Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0716 (input speed sensor signal drop check): lowest engine torque at which a fault could be scored. The check is switched off on this truck (no usable input speed sensor, the code is disabled), so this value has no effect. Stock 0 Nm. Effect: no effect on this truck Evidence: ledger:E0783, ledger:E0806, ledger:E1102</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F818" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x868" flags="0x0">
    <title>P0716 Fail - Engine Torque Maximum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0716 (input speed sensor sudden drop): a speed drop counts as a fault only at or below this engine torque. Stock 0 Nm. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0783, ledger:E1402</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F816" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x869" flags="0x0">
    <title>P0716 Fail - Speed Drop (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0716 (input speed sensor sudden drop): a drop of input speed between two 25 ms samples of at least this starts the fault time. Stock 0 rpm. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0783, ledger:E1402</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F804" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x86A" flags="0x0">
    <title>P0716 Fail - Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0716 (input speed sensor sudden drop): time the signal must stay down after a sudden drop to set the code. Stock 409.6 s. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0783, ledger:E1402</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F80E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x86B" flags="0x0">
    <title>P0503 Test - Arming Output Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): the check arms only after output speed has been above this. Stock 400 rpm. Effect: raise = the check arms at higher speed Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F83A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x86C" flags="0x0">
    <title>P0503 Test - Arming Time Above Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): time above the arming output speed before the check arms. Stock 2 s. Effect: raise = the check arms later Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F844" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x86D" flags="0x0">
    <title>P0503 Test - Arming Rise Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): a rise of output speed between two samples larger than this restarts the arming time. Stock 600 rpm. Effect: raise = larger speed jumps do not restart arming Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F83C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x86E" flags="0x0">
    <title>P0503 Test - Arming Time Without Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): time without a large rise of output speed before the check arms. Stock 2 s. Effect: raise = the check arms later Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F846" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x86F" flags="0x0">
    <title>P0502 Test - Run Condition, Engine Torque Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): highest engine torque at which the check runs in a drive range. Stock 550 Nm. Effect: lower = the check stops at lower torque Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F81A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x870" flags="0x0">
    <title>P0502 Test - Run Condition, Engine Torque Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): lowest engine torque at which the check runs in a drive range. Stock 65 Nm. Effect: raise = the check needs more engine torque Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F81C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x871" flags="0x0">
    <title>P0502 Fail - Output Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): output speed at or below this, with the run conditions met, counts as no signal. Stock 100 rpm. Effect: lower = a lower reading is needed to count as no signal Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F81E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x872" flags="0x0">
    <title>P0502 Pass - Output Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): output speed at or above which the pass time runs. Stock 250 rpm. Effect: raise = the check needs a higher speed to pass Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F820" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x873" flags="0x0">
    <title>P0502 Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): time at or above the pass speed that passes the check. Stock 1.5 s. Effect: raise = the check takes longer to pass Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F822" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x874" flags="0x0">
    <title>P0502 Test - Run Condition, Engine Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): highest engine speed at which the check runs. Stock 5000 rpm. Effect: lower = the check stops at lower engine speed Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F824" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x875" flags="0x0">
    <title>P0502 Test - Run Condition, Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): lowest engine speed at which the check runs. Stock 2850 rpm. Effect: lower = the check also runs at lower engine speed Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F826" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x876" flags="0x0">
    <title>P0502 Test - Run Condition, Throttle Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): lowest driver throttle at which the check runs. Stock 10 %. Effect: raise = the check needs more throttle Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F828" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x877" flags="0x0">
    <title>P0502 Test - Run Condition, Converter Slip Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): lowest torque converter slip at which the check runs. Stock -0.125 rpm: the check is off while slip is negative (it is a limit, not an off value). Effect: raise = the check needs positive converter slip Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F82C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x878" flags="0x0">
    <title>P0502 Test - Run Condition, Fluid Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): lowest transmission fluid temperature at which the check runs. Stock just below 0 C (a limit, not an off value). Effect: raise = the check needs warmer fluid Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F832" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x879" flags="0x0">
    <title>P0503 Pass - Output Speed Drop Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): largest drop of output speed between two 25 ms samples that still counts as good for the pass time. Stock 500 rpm. Effect: raise = larger drops still count as good Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F834" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x87A" flags="0x0">
    <title>P0503 Pass - Output Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): output speed at or above which the pass time runs. Stock 500 rpm. Effect: raise = the check passes only at higher speed Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F838" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x87B" flags="0x0">
    <title>P0503 Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): time of good signal that passes the check. Stock 2 s. Effect: raise = the check takes longer to pass Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F840" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x87C" flags="0x0">
    <title>P0503 Fail - Output Speed Drop</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): a drop of output speed between two 25 ms samples of at least this starts the fault timer. Stock 350 rpm. Effect: raise = a larger sudden drop is needed to start the fault timer Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F836" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x87D" flags="0x0">
    <title>P0503 Fail - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): time the signal must stay down after a sudden drop to set the code. Stock 3.25 s. Effect: raise = the signal must stay down longer Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F842" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x87E" flags="0x0">
    <title>Input Speed Sensor - Timer Scale (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scale of the pulse timer in the input speed calculation: the input speed reading is proportional to it. Stock 1.0. Part of how the PCM turns the input (turbine) speed sensor&#x27;s pulse count and pulse timer into input speed. Structural: DO NOT EDIT. Effect: DO NOT EDIT: changes every input speed reading Evidence: ledger:E0783, ledger:E1516</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF06" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x87F" flags="0x0">
    <title>Input Speed Sensor - Pulse Timer Rollover Correction (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Timer counts taken off the pulse time change when the pulse timer rolls over. Stock 0 (the timer rolls over at its full 16-bit range). Part of how the PCM turns the input (turbine) speed sensor&#x27;s pulse count and pulse timer into input speed. Structural: DO NOT EDIT. Effect: DO NOT EDIT: changes every input speed reading Evidence: ledger:E0783, ledger:E1516</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF08" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x880" flags="0x0">
    <title>Input Speed Sensor - Pulse Count Rollover Correction (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pulses taken off the pulse count change when the pulse counter rolls over. Stock 0 (the counter rolls over at its full 16-bit range). Part of how the PCM turns the input (turbine) speed sensor&#x27;s pulse count and pulse timer into input speed. Structural: DO NOT EDIT. Effect: DO NOT EDIT: changes every input speed reading Evidence: ledger:E0783, ledger:E1516</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF0A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>pulses</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x881" flags="0x0">
    <title>Input Speed Sensor - Pulses per Revolution</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of input (turbine) speed sensor pulses per revolution, used to turn the sensor pulse rate into input speed. Stock 36. Must match the sensor&#x27;s reluctor; a wrong value scales every input speed reading (slip, gear ratio and converter calculations). Effect: raise = lower input speed reading for the same pulse rate: edit only for a different reluctor Evidence: ledger:E0783, ledger:E1513</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF0C" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>pulses/rev</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x882" flags="0x0">
    <title>Trans Slip (P0894) Arm - Fluid Temp Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 20.1 C. The P0894 (transmission component slipping) test only runs while this and its other conditions hold: converter clutch applied, 3rd or 4th gear with a plausible engine to output speed ratio, converter clutch command and pressure held high, no related faults, and fluid temperature, engine torque, vehicle speed and engine speed inside their windows. Effect: raise = the test needs warmer fluid Evidence: ledger:E0786, ledger:E0807, ledger:E0849, ledger:E0853</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F72E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x883" flags="0x0">
    <title>Trans Slip (P0894) Arm - Fluid Temp Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 130.5 C. The P0894 (transmission component slipping) test only runs while this and its other conditions hold: converter clutch applied, 3rd or 4th gear with a plausible engine to output speed ratio, converter clutch command and pressure held high, no related faults, and fluid temperature, engine torque, vehicle speed and engine speed inside their windows. Effect: lower = the test stops at a lower fluid temperature Evidence: ledger:E0786, ledger:E0849, ledger:E0853</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F72C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x884" flags="0x0">
    <title>Trans Slip (P0894) Arm - Engine Torque Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0894 (transmission component slipping) test: the test arms only with engine torque at or above this. Stock 65 Nm. Effect: raise = the test needs more engine torque Evidence: ledger:E0786, ledger:E0806, ledger:E1095</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F700" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x885" flags="0x0">
    <title>Trans Slip (P0894) Arm - Engine Torque Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 550 Nm. The P0894 (transmission component slipping) test only runs while this and its other conditions hold: converter clutch applied, 3rd or 4th gear with a plausible engine to output speed ratio, converter clutch command and pressure held high, no related faults, and fluid temperature, engine torque, vehicle speed and engine speed inside their windows. Effect: lower = the test stops at lower engine torque Evidence: ledger:E0786, ledger:E0849, ledger:E0853</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F6FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x886" flags="0x0">
    <title>Trans Slip (P0894) Arm - Speed Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 55 km/h (transmission-side speed). The P0894 (transmission component slipping) test only runs while this and its other conditions hold: converter clutch applied, 3rd or 4th gear with a plausible engine to output speed ratio, converter clutch command and pressure held high, no related faults, and fluid temperature, engine torque, vehicle speed and engine speed inside their windows. Effect: raise = the test needs a higher speed Evidence: ledger:E0786, ledger:E0807, ledger:E0849, ledger:E0853</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F732" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x887" flags="0x0">
    <title>Trans Slip (P0894) Arm - Speed Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 140 km/h (transmission-side speed). The P0894 (transmission component slipping) test only runs while this and its other conditions hold: converter clutch applied, 3rd or 4th gear with a plausible engine to output speed ratio, converter clutch command and pressure held high, no related faults, and fluid temperature, engine torque, vehicle speed and engine speed inside their windows. Effect: lower = the test stops at a lower speed Evidence: ledger:E0786, ledger:E0849, ledger:E0853</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F730" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x888" flags="0x0">
    <title>Trans Slip (P0894) Arm - Engine Speed Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 1000 rpm. The P0894 (transmission component slipping) test only runs while this and its other conditions hold: converter clutch applied, 3rd or 4th gear with a plausible engine to output speed ratio, converter clutch command and pressure held high, no related faults, and fluid temperature, engine torque, vehicle speed and engine speed inside their windows. Effect: raise = the test needs a higher engine speed Evidence: ledger:E0786, ledger:E0807, ledger:E0849, ledger:E0853</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F718" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x889" flags="0x0">
    <title>Trans Slip (P0894) Arm - Engine Speed Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 4500 rpm. The P0894 (transmission component slipping) test only runs while this and its other conditions hold: converter clutch applied, 3rd or 4th gear with a plausible engine to output speed ratio, converter clutch command and pressure held high, no related faults, and fluid temperature, engine torque, vehicle speed and engine speed inside their windows. Effect: lower = the test stops at a lower engine speed Evidence: ledger:E0786, ledger:E0849, ledger:E0853</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F716" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x88A" flags="0x0">
    <title>P2771 Fault Test, High Range Assumed - Converter Slip Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, high range assumed: with the converter clutch applied, converter slip at or above this runs the fault test. Stock 100 rpm. The check runs in 4th gear; converter slip is worked out from the assumed range, so a wrong range shows up as a large slip. Effect: raise = more slip is needed to run the fault test Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F770" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x88B" flags="0x0">
    <title>P2771 Fault Test, High Range Assumed - Converter Slip Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, high range assumed: the fault test runs with converter slip at or below this. Stock 4095.75 rpm: no upper limit. (This one word is in steps of 0.25 rpm.) The check runs in 4th gear; converter slip is worked out from the assumed range, so a wrong range shows up as a large slip. Effect: lower = very large slip no longer runs the fault test Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F76E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x88C" flags="0x0">
    <title>P2771 Pass Test, High Range Assumed - Converter Slip Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, high range assumed: the pass test runs with converter slip at or above this. Stock -20 rpm. The check runs in 4th gear; converter slip is worked out from the assumed range, so a wrong range shows up as a large slip. Effect: lower = the pass test also runs at more negative slip Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F76C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x88D" flags="0x0">
    <title>P2771 Pass Test, High Range Assumed - Converter Slip Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, high range assumed: the pass test runs with converter slip at or below this. Stock 300 rpm, but slip from the fault test minimum (100 rpm) up runs the fault test instead. The check runs in 4th gear; converter slip is worked out from the assumed range, so a wrong range shows up as a large slip. Effect: lower = the pass test stops at lower slip Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F76A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x88E" flags="0x0">
    <title>P2771 Fault Test, Low Range Assumed - Converter Slip Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, low range assumed: the fault test runs with converter slip at or above this. Stock -4000 rpm. The check runs in 4th gear; converter slip is worked out from the assumed range, so a wrong range shows up as a large slip. Effect: raise = very negative slip no longer runs the fault test Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F768" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x88F" flags="0x0">
    <title>P2771 Fault Test, Low Range Assumed - Converter Slip Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, low range assumed: the fault test runs with converter slip at or below this (a large negative slip). Stock -50 rpm. The check runs in 4th gear; converter slip is worked out from the assumed range, so a wrong range shows up as a large slip. Effect: lower = a more negative slip is needed to run the fault test Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F766" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x890" flags="0x0">
    <title>P2771 Pass Test, Low Range Assumed - Converter Slip Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, low range assumed: the pass test runs with converter slip at or above this. Stock -20 rpm. The check runs in 4th gear; converter slip is worked out from the assumed range, so a wrong range shows up as a large slip. Effect: lower = the pass test also runs at more negative slip Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F764" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x891" flags="0x0">
    <title>P2771 Pass Test, High Range Assumed - Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, high range assumed: bottom of the window of engine speed over (output speed x gear ratio) that agrees with high range. Stock window 0.690 to 1.300. Effect: raise = lower ratios no longer pass Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F756" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x892" flags="0x0">
    <title>P2771 Pass Test, High Range Assumed - Ratio Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, high range assumed: top of the window of engine speed over (output speed x gear ratio) that agrees with high range. Stock window 0.690 to 1.300. Effect: lower = higher ratios no longer pass Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F758" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x893" flags="0x0">
    <title>P2771 Fault Test, Low Range Assumed - Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, low range assumed: bottom of the window of engine speed over (output speed x gear ratio) that means the transfer case is really in high range. Stock window 0.680 to 1.750. Effect: raise = lower ratios no longer count as high range Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F75A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x894" flags="0x0">
    <title>P2771 Fault Test, Low Range Assumed - Ratio Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, low range assumed: top of the window of engine speed over (output speed x gear ratio) that means the transfer case is really in high range. Stock window 0.680 to 1.750. Effect: lower = higher ratios no longer count as high range Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F75C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x895" flags="0x0">
    <title>P2771 Pass Test, Low Range Assumed - Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, low range assumed: bottom of the window of engine speed over (output speed x gear ratio) that agrees with low range. Stock window 3.720 to 4.280. Effect: raise = lower ratios no longer pass Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F75E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x896" flags="0x0">
    <title>P2771 Pass Test, Low Range Assumed - Ratio Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, low range assumed: top of the window of engine speed over (output speed x gear ratio) that agrees with low range. Stock window 3.720 to 4.280. Effect: lower = higher ratios no longer pass Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F760" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x897" flags="0x0">
    <title>P2771 Pass Test, Low Range Assumed - Converter Slip Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, low range assumed: the pass test runs with converter slip at or below this. Stock 50 rpm. The check runs in 4th gear; converter slip is worked out from the assumed range, so a wrong range shows up as a large slip. Effect: raise = the pass test also runs at higher slip Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F762" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x898" flags="0x0">
    <title>P0711 Cold Start Check - Drive Timer Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The check&#x27;s drive timer only counts while trans-side speed is at or above this. Stock 20 km/h. P0711 cold start check: when the transmission fluid temperature read -38 to 21 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 cold start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x899" flags="0x0">
    <title>P0711 Cold Start Check - Drive Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Drive time, counted at or above the speed minimum, the check needs before it can run. Stock 700 s. P0711 cold start check: when the transmission fluid temperature read -38 to 21 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 cold start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x89A" flags="0x0">
    <title>P0711 Cold Start Check - Slip Timer TCC Slip Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The check&#x27;s slip timer only counts while TCC slip is at or above this. Stock 50 rpm. P0711 cold start check: when the transmission fluid temperature read -38 to 21 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 cold start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x89B" flags="0x0">
    <title>P0711 Cold Start Check - Slip Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time with TCC slip at or above the slip minimum the check needs before it can run. Stock 500 s. P0711 cold start check: when the transmission fluid temperature read -38 to 21 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 cold start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x89C" flags="0x0">
    <title>P0711 Cold Start Check - Start Temperature Window Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest transmission fluid temperature at engine start for which the check runs. Stock -38 C. P0711 cold start check: when the transmission fluid temperature read -38 to 21 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 cold start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x89D" flags="0x0">
    <title>P0711 Cold Start Check - Start Temperature Window High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest transmission fluid temperature at engine start for which the check runs. Stock 21 C. P0711 cold start check: when the transmission fluid temperature read -38 to 21 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 cold start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x89E" flags="0x0">
    <title>P0711 Cold Start Check - Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The check only runs with coolant at or above this. Stock 70 C. P0711 cold start check: when the transmission fluid temperature read -38 to 21 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 cold start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x89F" flags="0x0">
    <title>P2771 Fault Test, High Range Assumed - Time per Event</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, high range assumed: time the ratio must stay in the fault window to count one event. Stock 5 s. Effect: raise = the wrong ratio must last longer for each event Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F772" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8A0" flags="0x0">
    <title>P2771 Fault Test, Low Range Assumed - Time per Event</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, low range assumed: time the ratio must stay in the fault window to count one event. Stock 5 s. Effect: raise = the wrong ratio must last longer for each event Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F773" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8A1" flags="0x0">
    <title>P2771 Pass Test, High Range Assumed - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, high range assumed: time the ratio must stay in the pass window to pass and clear the event count. Stock 0.5 s. Effect: raise = the check takes longer to pass Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F774" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8A2" flags="0x0">
    <title>P2771 Pass Test, Low Range Assumed - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, low range assumed: time the ratio must stay in the pass window to pass and clear the event count. Stock 0.5 s. Effect: raise = the check takes longer to pass Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F775" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8A3" flags="0x0">
    <title>P2771 Fault Test, High Range Assumed - Events to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, high range assumed: number of fault events that sets the code. Stock 2. Effect: raise = more events are needed to set the code Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F776" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8A4" flags="0x0">
    <title>P2771 Fault Test, Low Range Assumed - Events to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check, low range assumed: number of fault events that sets the code. Stock 2. Effect: raise = more events are needed to set the code Evidence: ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F777" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8A5" flags="0x0">
    <title>P0713 Test - Drive Timer Output Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0713 (transmission fluid temperature sensor circuit high): the drive time counts while transmission output speed is at or above this. Stock 100 rpm. Effect: raise = drive time only counts at higher speed Evidence: ledger:E1093</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F77A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8A6" flags="0x0">
    <title>P0713 Test - Slip Timer Converter Slip Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0713 (transmission fluid temperature sensor circuit high): the slip time counts while torque converter slip is at or above this. Stock 100 rpm. Effect: raise = slip time only counts at higher converter slip Evidence: ledger:E1093</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F77C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8A7" flags="0x0">
    <title>P0713 Test - Drive Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0713 (transmission fluid temperature sensor circuit high): drive time needed before the check may fail (the fluid must have had time to warm). Stock 300 s. Effect: raise = the check waits for more driving Evidence: ledger:E1093</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F780" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8A8" flags="0x0">
    <title>P0713 Test - Slip Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0713 (transmission fluid temperature sensor circuit high): converter slip time needed before the check may fail. Stock 300 s. Effect: raise = the check waits for more converter slip time Evidence: ledger:E1093</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F782" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8A9" flags="0x0">
    <title>P0711 Test - Fluid Temperature Reading Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0711 (transmission fluid temperature sensor performance): the checks run only while the raw fluid temperature reading is at or below this. Stock 149 C. Effect: lower = the checks stop at a lower reading Evidence: ledger:E1093</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8AA" flags="0x0">
    <title>P0711 Test - Fluid Temperature Reading Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0711: the checks run only while the raw fluid temperature reading is at or above this. Stock -38 C. Effect: raise = the checks need a warmer reading Evidence: ledger:E1093</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8AB" flags="0x0">
    <title>P0711 Cold Start Check - Coolant Rise Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The coolant must have risen at least this much since engine start. Stock 50 C. P0711 cold start check: when the transmission fluid temperature read -38 to 21 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 cold start check runs or sets Evidence: ledger:E0786, ledger:E0817, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8AC" flags="0x0">
    <title>P0711 Cold Start Check - Stuck Reading Tolerance</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0711 counts toward a fail while the transmission fluid reading is still within this of its start value. Stock 2 C. P0711 cold start check: when the transmission fluid temperature read -38 to 21 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 cold start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8AD" flags="0x0">
    <title>P0711 Cold Start Check - Fail Confirm Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0711 sets once the stuck reading has lasted this long. Stock 80 s. P0711 cold start check: when the transmission fluid temperature read -38 to 21 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 cold start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8AE" flags="0x0">
    <title>P0711 Hot Start Check - Drive Timer Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The check&#x27;s drive timer only counts while trans-side speed is at or above this. Stock 20 km/h. P0711 hot start check: when the transmission fluid temperature read 131 to 149 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 hot start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8AF" flags="0x0">
    <title>P0711 Hot Start Check - Drive Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Drive time, counted at or above the speed minimum, the check needs before it can run. Stock 700 s. P0711 hot start check: when the transmission fluid temperature read 131 to 149 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 hot start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8B0" flags="0x0">
    <title>P0711 Hot Start Check - Slip Timer TCC Slip Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The check&#x27;s slip timer only counts while TCC slip is at or above this. Stock 50 rpm. P0711 hot start check: when the transmission fluid temperature read 131 to 149 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 hot start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8B1" flags="0x0">
    <title>P0711 Hot Start Check - Slip Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time with TCC slip at or above the slip minimum the check needs before it can run. Stock 500 s. P0711 hot start check: when the transmission fluid temperature read 131 to 149 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 hot start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8B2" flags="0x0">
    <title>P0711 Hot Start Check - Start Temperature Window Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest transmission fluid temperature at engine start for which the check runs. Stock 131 C. P0711 hot start check: when the transmission fluid temperature read 131 to 149 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 hot start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8B3" flags="0x0">
    <title>P0711 Hot Start Check - Start Temperature Window High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest transmission fluid temperature at engine start for which the check runs. Stock 149 C. P0711 hot start check: when the transmission fluid temperature read 131 to 149 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 hot start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8B4" flags="0x0">
    <title>P0711 Hot Start Check - Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The check only runs with coolant at or above this. Stock 70 C. P0711 hot start check: when the transmission fluid temperature read 131 to 149 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 hot start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8B5" flags="0x0">
    <title>P0711 Hot Start Check - Coolant Rise Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The coolant must have risen at least this much since engine start. Stock 50 C. P0711 hot start check: when the transmission fluid temperature read 131 to 149 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 hot start check runs or sets Evidence: ledger:E0786, ledger:E0817, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8B6" flags="0x0">
    <title>P0711 Hot Start Check - Stuck Reading Tolerance</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0711 counts toward a fail while the transmission fluid reading is still within this of its start value. Stock 2 C. P0711 hot start check: when the transmission fluid temperature read 131 to 149 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 hot start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8B7" flags="0x0">
    <title>P0711 Hot Start Check - Fail Confirm Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0711 sets once the stuck reading has lasted this long. Stock 80 s. P0711 hot start check: when the transmission fluid temperature read 131 to 149 C at engine start, it must move by more than the stuck-reading tolerance once the engine has warmed up and the truck has been driven; a reading that stays put is reported as a stuck sensor. Effect: changes when the P0711 hot start check runs or sets Evidence: ledger:E0786, ledger:E0911</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8B8" flags="0x0">
    <title>Trans Over Temperature Check Enable (P0218)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the transmission over temperature check on or off. 1: the PCM runs the check and can set P0218. 0: the check never runs, so P0218 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0218 check off (never set); 1 = check on Evidence: ledger:E0786, ledger:E0975, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8B9" flags="0x0">
    <title>P0218 - Sensor Plausible Range Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0218 (transmission fluid over temperature): the fluid temperature sensor reading must be at or above this for the check to run. Stock -39.75 C. Effect: raise = the check is skipped at colder sensor readings Evidence: ledger:E0786, ledger:E0975</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7D8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8BA" flags="0x0">
    <title>P0218 - Sensor Plausible Range High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0218 (transmission fluid over temperature): the fluid temperature sensor reading must be at or below this for the check to run. Stock 149.75 C. Effect: lower = the check is skipped at hotter sensor readings Evidence: ledger:E0786, ledger:E0975</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7DA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8BB" flags="0x0">
    <title>P0218 - Sensor Plausible Time Before Checking</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0218 (transmission fluid over temperature): the check only starts once the fluid temperature sensor has read inside its plausible range for this long. Stock 5 s. Effect: raise = the check starts later Evidence: ledger:E0786, ledger:E0975</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7E0" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8BC" flags="0x0">
    <title>P0218 - Fail Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0218 (transmission fluid over temperature): the check counts toward a fail while transmission fluid temperature is at or above this. Stock 130 C. Effect: raise = P0218 needs hotter fluid to set (can hide an overheating transmission) Evidence: ledger:E0786, ledger:E0975</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7DC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8BD" flags="0x0">
    <title>P0218 - Fail Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0218 (transmission fluid over temperature): P0218 sets once fluid temperature has stayed at or above the fail temperature for this long without dropping to the pass temperature. Stock 600 s (10 minutes). Effect: raise = P0218 takes longer to set (can hide an overheating transmission) Evidence: ledger:E0786, ledger:E0975</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8BE" flags="0x0">
    <title>P0218 - Pass Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0218 (transmission fluid over temperature): the check counts toward a pass, and restarts the fail time, while fluid temperature is at or below this. Stock 129.5 C. Effect: lower = the fluid must cool further before the check passes Evidence: ledger:E0786, ledger:E0975</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7DE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8BF" flags="0x0">
    <title>P0218 - Pass Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0218 (transmission fluid over temperature): the check reports a pass once fluid temperature has stayed at or below the pass temperature for this long. Stock 5 s. Effect: raise = the check takes longer to pass Evidence: ledger:E0786, ledger:E0975</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7E1" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8C0" flags="0x0">
    <title>Shift Torque Re-Latch - Upshift Lift-Off Drop</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During an upshift, a throttle drop from the reference of at least this (with the throttle also below the lift-off throttle) is a lift-off: the shift torque is taken from the gearbox torque at that moment. Stock 25 %. The shift torque is the torque every shift pressure table is looked up with; it is latched when the shift starts and these throttle checks decide when it is taken again mid-shift. In one of the three downshift pressure modes the downshift torque is re-taken only on a lift-off or a recovery; in the others it follows the live torque estimate throughout. Effect: raise = a bigger throttle drop is needed to count as a...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E694" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8C1" flags="0x0">
    <title>Shift Torque Re-Latch - Upshift Lift-Off Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During an upshift, a lift-off also needs the throttle below this. Stock 3.1 %. The shift torque is the torque every shift pressure table is looked up with; it is latched when the shift starts and these throttle checks decide when it is taken again mid-shift. In one of the three downshift pressure modes the downshift torque is re-taken only on a lift-off or a recovery; in the others it follows the live torque estimate throughout. Effect: raise = a lift-off is recognised with more throttle still applied Evidence: ledger:E0787, ledger:E1395</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E696" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8C2" flags="0x0">
    <title>Shift Torque Re-Latch - Upshift Recovery Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During an upshift, once the throttle rises above the reference throttle by more than this, the shift torque is taken again from the live torque estimate (recovered). Stock 6.25 %. The shift torque is the torque every shift pressure table is looked up with; it is latched when the shift starts and these throttle checks decide when it is taken again mid-shift. In one of the three downshift pressure modes the downshift torque is re-taken only on a lift-off or a recovery; in the others it follows the live torque estimate throughout. Effect: raise = a larger throttle rise is needed before the shift torque follows the live torque Ev...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E692" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8C3" flags="0x0">
    <title>Shift Torque Re-Latch - Upshift Partial Drop</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During an upshift, a throttle drop from the reference of more than this that is not a full lift-off re-takes the shift torque from the live torque estimate once per shift, and moves the reference to the current throttle. Stock 6.25 %. The shift torque is the torque every shift pressure table is looked up with; it is latched when the shift starts and these throttle checks decide when it is taken again mid-shift. In one of the three downshift pressure modes the downshift torque is re-taken only on a lift-off or a recovery; in the others it follows the live torque estimate throughout. Effect: raise = smaller throttle drops leave...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E698" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8C4" flags="0x0">
    <title>Shift Torque Re-Latch - Downshift Lift-Off Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During a downshift, a lift-off also needs the throttle below this. Stock 20.0 %. The shift torque is the torque every shift pressure table is looked up with; it is latched when the shift starts and these throttle checks decide when it is taken again mid-shift. In one of the three downshift pressure modes the downshift torque is re-taken only on a lift-off or a recovery; in the others it follows the live torque estimate throughout. Effect: raise = a lift-off is recognised with more throttle still applied Evidence: ledger:E0787, ledger:E1395</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E69C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8C5" flags="0x0">
    <title>Shift Torque Re-Latch - Downshift Recovery Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During a downshift, a throttle rise above the reference of at least this counts as recovered. Stock 18.9 %. The shift torque is the torque every shift pressure table is looked up with; it is latched when the shift starts and these throttle checks decide when it is taken again mid-shift. In one of the three downshift pressure modes the downshift torque is re-taken only on a lift-off or a recovery; in the others it follows the live torque estimate throughout. Effect: raise = a larger throttle rise is needed to count as recovered Evidence: ledger:E0787, ledger:E1395</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E69E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8C6" flags="0x0">
    <title>Trans Torque Override - On, Min Engine Speed (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at or above which the torque override can switch on. Stock 0 rpm. The torque override replaces the filtered engine torque the transmission works from with the torque override vs throttle curve. It switches on while engine speed, positive engine torque and throttle meet the on set, and once on it stays on while they meet the hold set. Inactive on stock: both torque limits are 0, so the override never engages. Effect: no effect on stock (inactive) Evidence: ledger:E0787, ledger:E0822, ledger:E1396</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E32A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8C7" flags="0x0">
    <title>Trans Torque Override - On, Engine Torque Below (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Positive engine torque must be below this for the torque override to switch on. Stock 0 Nm: never. The torque override replaces the filtered engine torque the transmission works from with the torque override vs throttle curve. It switches on while engine speed, positive engine torque and throttle meet the on set, and once on it stays on while they meet the hold set. Inactive on stock: both torque limits are 0, so the override never engages. Effect: no effect on stock (inactive); above 0 = the override can switch on below that torque Evidence: ledger:E0787, ledger:E0822, ledger:E1396</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E32E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8C8" flags="0x0">
    <title>Trans Torque Override - On, Min Throttle (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle at or above which the torque override can switch on. Stock 0 %. The torque override replaces the filtered engine torque the transmission works from with the torque override vs throttle curve. It switches on while engine speed, positive engine torque and throttle meet the on set, and once on it stays on while they meet the hold set. Inactive on stock: both torque limits are 0, so the override never engages. Effect: no effect on stock (inactive) Evidence: ledger:E0787, ledger:E0822, ledger:E1396</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E332" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8C9" flags="0x0">
    <title>Trans Torque Override - Hold, Min Engine Speed (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at or above which a torque override that is on stays on. Stock 0 rpm. The torque override replaces the filtered engine torque the transmission works from with the torque override vs throttle curve. It switches on while engine speed, positive engine torque and throttle meet the on set, and once on it stays on while they meet the hold set. Inactive on stock: both torque limits are 0, so the override never engages. Effect: no effect on stock (inactive) Evidence: ledger:E0787, ledger:E0822, ledger:E1396</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E32C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8CA" flags="0x0">
    <title>Trans Torque Override - Hold, Engine Torque Below (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Positive engine torque must stay below this for a torque override that is on to stay on. Stock 0 Nm. The torque override replaces the filtered engine torque the transmission works from with the torque override vs throttle curve. It switches on while engine speed, positive engine torque and throttle meet the on set, and once on it stays on while they meet the hold set. Inactive on stock: both torque limits are 0, so the override never engages. Effect: no effect on stock (inactive) Evidence: ledger:E0787, ledger:E0822, ledger:E1396</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E330" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8CB" flags="0x0">
    <title>Trans Torque Override - Hold, Min Throttle (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle at or above which a torque override that is on stays on. Stock 0 %. The torque override replaces the filtered engine torque the transmission works from with the torque override vs throttle curve. It switches on while engine speed, positive engine torque and throttle meet the on set, and once on it stays on while they meet the hold set. Inactive on stock: both torque limits are 0, so the override never engages. Effect: no effect on stock (inactive) Evidence: ledger:E0787, ledger:E0822, ledger:E1396</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E334" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8CC" flags="0x0">
    <title>Trans Engine Torque Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How quickly the filtered engine torque the transmission works from follows the engine&#x27;s net torque: the fraction of the change taken per update. The filtered torque is turned into turbine torque, gearbox torque and the shift torque the shift pressure tables are looked up with. Stock 0.98. Effect: raise = the transmission torque follows engine torque changes faster; lower = smoother but lags more Evidence: ledger:E0787, ledger:E1396</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E326" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8CD" flags="0x0">
    <title>Trans Throttle Torque Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Smoothing of the throttle torque estimate used by the torque reduction during shifts: the fraction of the change taken per update. Stock 0: no smoothing, the estimate is used as it is. Effect: above 0 = the throttle torque estimate used for the shift torque reduction is smoothed (smaller = smoother) Evidence: ledger:E0787, ledger:E1396</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E328" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8CE" flags="0x0">
    <title>Output Speed Sensor - Timer Scale (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scale of the pulse timer in the output speed calculation: the output speed reading is proportional to it. Stock 1.0. Part of how the PCM turns the output shaft speed sensor&#x27;s pulse count and pulse timer into output speed (the same calculation as the input speed sensor). Structural: DO NOT EDIT. Effect: DO NOT EDIT: changes every output speed reading Evidence: ledger:E0787, ledger:E1537</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF34" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8CF" flags="0x0">
    <title>Output Speed Sensor - Pulse Timer Rollover Correction (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Timer counts taken off the pulse time change when the pulse timer rolls over. Stock 0 (the timer rolls over at its full 16-bit range). Part of how the PCM turns the output shaft speed sensor&#x27;s pulse count and pulse timer into output speed (the same calculation as the input speed sensor). Structural: DO NOT EDIT. Effect: DO NOT EDIT: changes every output speed reading Evidence: ledger:E0787, ledger:E1537</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF36" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8D0" flags="0x0">
    <title>Output Speed Sensor - Pulse Count Rollover Correction (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pulses taken off the pulse count change when the pulse counter rolls over. Stock 0 (the counter rolls over at its full 16-bit range). Part of how the PCM turns the output shaft speed sensor&#x27;s pulse count and pulse timer into output speed (the same calculation as the input speed sensor). Structural: DO NOT EDIT. Effect: DO NOT EDIT: changes every output speed reading Evidence: ledger:E0787, ledger:E1537</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF38" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>pulses</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x8D1" flags="0x30">
    <title>Downshift Monitor - Delay Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Subtracted from the measured downshift delay, by downshift (stock 0 s). Part of the downshift monitor, which follows each downshift from the request until the gear ratio reaches the new gear or a time limit ends it; the measured downshift delay feeds the shift adapt and torque logic. Effect: raise = shorter measured delay Evidence: ledger:E1428</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>downshift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2-1" />
      <LABEL index="1" value="3-2" />
      <LABEL index="2" value="4-3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39DA6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x8D2" flags="0x0">
    <title>Trans Ratio Monitor A - Forced Reset Speed Ratio (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this measured converter speed ratio the gear ratio monitor resets its working state instead of running its checks. Stock 0, so the reset never happens on this calibration. Effect: no effect on stock (inactive) Evidence: ledger:E0788, ledger:E0859</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39EE8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8D3" flags="0x0">
    <title>Ratio Monitor A, Settle Time Low Bound</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this much time since the last gear change, this transmission ratio monitor holds its output flag off. Stock 0.1 seconds. Effect: raise = the monitor waits longer after a shift before it is even eligible to set its flag Evidence: ledger:E0788, ledger:E0806</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39EEC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8D4" flags="0x0">
    <title>Ratio Monitor A, Settle Time High Bound</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once this much time has passed since the last gear change, this transmission ratio monitor sets its output flag on by itself, regardless of the other condition it normally checks. Stock 2.0 seconds. Effect: lower = the monitor forces its flag on sooner after a shift, on time alone Evidence: ledger:E0788, ledger:E0806</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39EEE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x8D5" flags="0x30">
    <title>Downshift Monitor - Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After this time since the downshift request the monitor ends, by downshift (stock 1.0 s). Part of the downshift monitor, which follows each downshift from the request until the gear ratio reaches the new gear or a time limit ends it; the measured downshift delay feeds the shift adapt and torque logic. Effect: raise = the monitor waits longer for the ratio change Evidence: ledger:E0725, ledger:E0788, ledger:E0806, ledger:E1428</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>downshift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2-1" />
      <LABEL index="1" value="3-2" />
      <LABEL index="2" value="4-3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39EF6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x8D6" flags="0x30">
    <title>Downshift Monitor - Settle Time at New Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once a downshift has reached the new gear, the monitor finishes after this long, by downshift (stock 1.0 s). Part of the downshift monitor, which follows each downshift from the request until the gear ratio reaches the new gear or a time limit ends it; the measured downshift delay feeds the shift adapt and torque logic. Effect: raise = the monitor stays in its at-new-gear state longer Evidence: ledger:E1428</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>downshift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2-1" />
      <LABEL index="1" value="3-2" />
      <LABEL index="2" value="4-3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39F02" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x8D7" flags="0x30">
    <title>Downshift Monitor - Ratio at New Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Gear ratio above which the downshift counts as reached the new gear, by downshift (stock 7.75: never, so on the stock calibration every downshift monitor ends by its time limit). Part of the downshift monitor, which follows each downshift from the request until the gear ratio reaches the new gear or a time limit ends it; the measured downshift delay feeds the shift adapt and torque logic. Effect: set to the new gear&#x27;s ratio (minus a margin) to measure the real downshift delay Evidence: ledger:E1428</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>downshift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2-1" />
      <LABEL index="1" value="3-2" />
      <LABEL index="2" value="4-3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39F08" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x8D8" flags="0x0">
    <title>Ratio Monitor B, Settle Time Low Bound</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this much time since the last gear change, this transmission ratio monitor holds its output flag off. Stock 0.1 seconds. Effect: raise = the monitor waits longer after a shift before it is even eligible to set its flag Evidence: ledger:E0788, ledger:E0806</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39EEA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x8D9" flags="0x30">
    <title>Ratio Monitor B, Downshift Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per downshift target gear, minimum time since the last gear change required before this transmission ratio monitor continues past its window check. Stock 2.0 / 2.0 / 3.0 seconds. Effect: raise = the monitor waits longer after a downshift to that gear before continuing its check Evidence: ledger:E0725, ledger:E0788, ledger:E0806</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39EF0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x8DA" flags="0x30">
    <title>Upshift Ratio Change - Start Ratio by Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Measured gear ratio at or below which an upshift counts as started (ratio leaving the old gear), for the 1-2, 2-3 and 3-4 shift. Stock 2.900 / 1.575 / 0.975. The time between the start and the end ratio is the measured shift time that the shift pressure adapt compares with the desired shift time, so these points move what the adapt learns. The downshift pressure ramp also uses these values, by the commanded gear (1st, 2nd, 3rd): during a downshift its ramp scales with how far the measured ratio has moved from its value at the downshift request toward this point. Effect: lower = the measured upshift starts later (shorter measu...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>upshift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E9A0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x8DB" flags="0x30">
    <title>Upshift Ratio Change - End Ratio by Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Measured gear ratio below which an upshift counts as complete (ratio at the new gear), for the 1-2, 2-3 and 3-4 shift. Stock 1.813 / 1.080 / 0.675. The time between the start and the end ratio is the measured shift time that the shift pressure adapt compares with the desired shift time, so these points move what the adapt learns. The stock 3-4 value (0.675) is below the 4th gear ratio (0.696), so a 3-4 upshift never counts as complete by ratio: it ends on the 3.0 s shift time limit instead, and the 3-4 measured shift time runs on to that limit. Effect: raise = the measured shift ends earlier (shorter measured shift time); a 3...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>upshift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E99A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x8DC" flags="0x0">
    <title>Shift Sol B Performance (P0756), 1st Gear - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time since the last shift that must pass before the shift solenoid B performance test (P0756) watches the transmission in 1st gear. Stock 2 s. The other conditions of the same check (throttle, torque and a converter speed ratio minimum) must hold as well. Effect: raise = the ratio check in 1st gear waits longer after a shift before it can run Evidence: ledger:E0788, ledger:E0806</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8DD" flags="0x0">
    <title>Shift Sol B Performance (P0756), 1st Gear - Torque Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower bound of the engine torque window required for the shift solenoid B performance test (P0756) to watch the transmission in 1st gear. Stock 50.0 Nm. Effect: raise = the ratio check in 1st gear needs more engine torque before it runs Evidence: ledger:E0788, ledger:E0806</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8DE" flags="0x0">
    <title>Shift Sol B Performance (P0756), 1st Gear - Torque Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper bound of the engine torque window required for the shift solenoid B performance test (P0756) to watch the transmission in 1st gear. Stock 550.0 Nm. Effect: lower = the ratio check in 1st gear stops running at a lower engine torque Evidence: ledger:E0788, ledger:E0806</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8DF" flags="0x0">
    <title>Shift Sol B Performance (P0756), 1st Gear - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest driver throttle-area request at which the shift solenoid B performance test (P0756) watches the transmission in 1st gear. Stock 25 %. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test runs only at a larger throttle request Evidence: ledger:E0788, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F60C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8E0" flags="0x0">
    <title>Shift Sol B Performance (P0756), 1st Gear - Converter Slip Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest torque converter slip (engine speed minus turbine speed) at which the shift solenoid B performance test (P0756) watches the transmission in 1st gear. Stock -1800 rpm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test needs more converter slip Evidence: ledger:E0788, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F622" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8E1" flags="0x0">
    <title>Shift Sol B Performance (P0756), 1st Gear - Converter Slip Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest torque converter slip (engine speed minus turbine speed) at which the shift solenoid B performance test (P0756) watches the transmission in 1st gear. Stock 2400 rpm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: lower = the test stops at less converter slip Evidence: ledger:E0788, ledger:E0841</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F624" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8E2" flags="0x0">
    <title>Shift Sol B Performance (P0756), 1st Gear - Output Speed Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest transmission output speed at which the shift solenoid B performance test (P0756) watches the transmission in 1st gear. Stock 100 rpm. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test needs a higher output speed Evidence: ledger:E0788, ledger:E0841, ledger:E0851</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F62E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8E3" flags="0x0">
    <title>Shift Sol B Performance (P0756), 1st Gear - Converter Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest converter speed ratio at which the shift solenoid B performance test (P0756) watches the transmission in 1st gear. Stock 0.2. The converter speed ratio here is the PCM&#x27;s own torque converter model estimate (turbine speed over engine speed, from engine speed and torque): 1.00 = coupled, low values = high slip. The other conditions of the same check (throttle, torque, time in gear and a converter speed condition) must hold as well. Effect: raise = the test waits until the converter is closer to coupled Evidence: ledger:E0788, ledger:E0841, ledger:E0851</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F59E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8E4" flags="0x0">
    <title>P2763 Fail - Commanded Duty Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2763 (converter clutch pulse width solenoid circuit check at high duty): a circuit fault counts as a fault sample only with the commanded solenoid duty at or above this. Stock 90 %. Effect: lower = faults are also counted at lower duty Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F682" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8E5" flags="0x0">
    <title>P2763 Fail - Fault Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2763 (converter clutch pulse width solenoid circuit check at high duty): fault samples inside the window that set the code. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the fault must be present for more of the window Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F67E" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8E6" flags="0x0">
    <title>P2763 Pass - Commanded Duty Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2763 (converter clutch pulse width solenoid circuit check at high duty): a clean circuit counts as a good sample only with the commanded solenoid duty at or above this. Stock 65 %. Effect: lower = the check can also pass at lower duty Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F684" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8E7" flags="0x0">
    <title>P2763 Pass - Good Sample Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2763 (converter clutch pulse width solenoid circuit check at high duty): good samples inside the window that pass the check. Stock 4.3 s of a 5 s window. The check counts 100 ms samples inside a window; the window length restarts the counts. Effect: raise = the circuit must read good for more of the window Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F67F" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8E8" flags="0x0">
    <title>P2763 Test - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2763 (converter clutch pulse width solenoid circuit check at high duty): length of the sample window. Stock 5 s. Keep it at or above the fail and pass times, or the check can never report. Effect: raise = fault samples may be spread over a longer time Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F680" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8E9" flags="0x0">
    <title>P2771 Test - Run Condition, Throttle Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check run condition: the check runs only with driver throttle at or above this. Stock 10 %. Effect: raise = the check needs more throttle Evidence: ledger:E0789, ledger:E0972, ledger:E1099</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F744" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8EA" flags="0x0">
    <title>P2771 Test - Run Condition, Throttle Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check run condition: the check runs only with driver throttle at or below this. Stock 99 %. Effect: lower = the check stops at less throttle Evidence: ledger:E0789, ledger:E0973, ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F746" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8EB" flags="0x0">
    <title>P2771 Test - Run Condition, Fluid Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check run condition: the check runs only with transmission fluid at or above this. Stock 20 C. Effect: raise = the check needs warmer fluid Evidence: ledger:E0789, ledger:E0972, ledger:E1099</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F748" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8EC" flags="0x0">
    <title>P2771 Test - Run Condition, Fluid Temperature Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check run condition: the check runs only with transmission fluid at or below this. Stock 130 C. Effect: lower = the check stops at lower fluid temperature Evidence: ledger:E0789, ledger:E0973, ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F74A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8ED" flags="0x0">
    <title>P2771 Test - Run Condition, Engine Torque Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check run condition: the check runs only with engine torque at or above this. Stock 5 Nm. Effect: raise = the check needs more engine torque Evidence: ledger:E0789, ledger:E0806, ledger:E1099</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F74E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8EE" flags="0x0">
    <title>P2771 Test - Run Condition, Engine Torque Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low range plausibility) check run condition: the check runs only with engine torque at or below this. Stock 525 Nm. Effect: lower = the check stops at lower torque Evidence: ledger:E0789, ledger:E0972, ledger:E1099</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F750" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8EF" flags="0x0">
    <title>Knock Tables - RPM Axis Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at the first column of the knock detection tables. Stock 0 rpm. Both knock tables that use this axis move with it: the knock detection threshold gains (one per cylinder) and the knock window angle term. Their rows or columns are spread evenly between the start and end values, so changing either end re-spaces every breakpoint; re-check those tables after an edit. Effect: raise = the knock tables start their first column at a higher rpm Evidence: ledger:E0364, ledger:E0831</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31C9C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8F0" flags="0x0">
    <title>Knock Tables - RPM Axis End</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at the last column of the knock detection tables; above it the last column is used. Stock 8000 rpm. Both knock tables that use this axis move with it: the knock detection threshold gains (one per cylinder) and the knock window angle term. Their rows or columns are spread evenly between the start and end values, so changing either end re-spaces every breakpoint; re-check those tables after an edit. Effect: raise = the knock tables cover a higher rpm range Evidence: ledger:E0364, ledger:E0831</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31C9E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8F1" flags="0x0">
    <title>Knock Tables - Cylinder Airmass Axis Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cylinder airmass at the first row of the knock detection tables. Stock 0.24 g. Both knock tables that use this axis move with it: the knock detection threshold gains (one per cylinder) and the knock window angle term. Their rows or columns are spread evenly between the start and end values, so changing either end re-spaces every breakpoint; re-check those tables after an edit. Effect: raise = the knock tables start their first row at a higher load Evidence: ledger:E0364, ledger:E0831</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31CC2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/cyl</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.095937</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8F2" flags="0x0">
    <title>Knock Tables - Cylinder Airmass Axis End</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cylinder airmass at the last row of the knock detection tables; above it the last row is used. Stock 0.72 g. This is the one engine load axis on this calibration that can be widened for boost: the spark, torque and fuel tables have fixed load ranges. Both knock tables that use this axis move with it: the knock detection threshold gains (one per cylinder) and the knock window angle term. Their rows or columns are spread evenly between the start and end values, so changing either end re-spaces every breakpoint; re-check those tables after an edit. Effect: raise = the knock tables cover higher cylinder loads (boost) Evidence: le...</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31CC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/cyl</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.095937</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8F3" flags="0x0">
    <title>Knock Threshold EQ Factor - EQ Axis Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded fuel equivalence ratio at the first point of the knock threshold EQ factor curve. Stock 1.00. The curve&#x27;s points are spread evenly between the start and end values. Effect: raise = the EQ factor curve starts at a richer mixture Evidence: ledger:E0364, ledger:E0831</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31CD8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8F4" flags="0x0">
    <title>Knock Threshold EQ Factor - EQ Axis End</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded fuel equivalence ratio at the last point of the knock threshold EQ factor curve; richer than this uses the last point. Stock 1.90. The curve&#x27;s points are spread evenly between the start and end values. Effect: raise = the EQ factor curve covers richer mixtures Evidence: ledger:E0364, ledger:E0831</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x31CDA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8F5" flags="0x0">
    <title>Over-Temp Enrichment - Entry Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Coolant at or above which the enrichment may start. Stock 119 C. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D0C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8F6" flags="0x0">
    <title>Over-Temp Enrichment - Hold Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Once active, the enrichment stays on while coolant is at or above this. Stock 115 C. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D0E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8F7" flags="0x0">
    <title>Over-Temp Enrichment - Entry Coolant (Status Bit Set)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Entry coolant used instead while bit 0 of the first diagnostic status byte is set. Stock 126 C. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D10" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8F8" flags="0x0">
    <title>Over-Temp Enrichment - Hold Coolant (Status Bit Set)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Hold coolant used instead while bit 0 of the first diagnostic status byte is set. Stock 122 C. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D12" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8F9" flags="0x0">
    <title>Over-Temp Enrichment - Entry Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Throttle at or above which the enrichment may start. Stock 50 %. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D14" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8FA" flags="0x0">
    <title>Over-Temp Enrichment - Hold Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Once active, throttle must stay at or above this. Stock 45 %. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D16" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8FB" flags="0x0">
    <title>Over-Temp Enrichment - Entry MAP</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Manifold pressure at or above which the enrichment may start. Stock 55 kPa. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D18" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8FC" flags="0x0">
    <title>Over-Temp Enrichment - Hold MAP</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Once active, manifold pressure must stay at or above this. Stock 50 kPa. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D1A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8FD" flags="0x0">
    <title>Over-Temp Enrichment - Entry Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Vehicle speed at or above which the enrichment may start. Stock 20 km/h. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D1C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8FE" flags="0x0">
    <title>Over-Temp Enrichment - Hold Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Once active, vehicle speed must stay at or above this. Stock 15 km/h. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26D1E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x8FF" flags="0x30">
    <title>Shift Torque Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift torque points used by the shift pressure, shift pressure multipliers, desired shift time and torque reduction tables. Stock 0 to 640 Nm in 40 Nm steps. Above the last point those tables use their last row, so a higher-torque engine needs this range widened. The tables that use it are spread over these points, so moving them re-spaces those tables; keep the point count and keep the points rising. Effect: moves the torque axis of every table that uses it: edit with care Evidence: ledger:E0706, ledger:E0834</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E3FE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x900" flags="0x30">
    <title>Shift Adapt Torque Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift torque points that select the shift pressure adapt cells. Stock 0 to 640 Nm in 40 Nm steps. The tables that use it are spread over these points, so moving them re-spaces those tables; keep the point count and keep the points rising. Effect: moves the torque axis of every table that uses it: edit with care Evidence: ledger:E0706, ledger:E0834</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3BFE8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x901" flags="0x30">
    <title>Upshift Pressure Temperature Modifier - Torque Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift torque points (rows) of the upshift pressure temperature modifier tables. Stock 0, 160, 320, 480, 640 Nm. The tables that use it are spread over these points, so moving them re-spaces those tables; keep the point count and keep the points rising. Effect: moves the torque axis of every table that uses it: edit with care Evidence: ledger:E0706, ledger:E0834</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A0F0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x902" flags="0x30">
    <title>Shift Profile Torque Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift torque points of the shift profile hold and end time tables. Stock 0 to 320 Nm in 20 Nm steps. The tables that use it are spread over these points, so moving them re-spaces those tables; keep the point count and keep the points rising. Effect: moves the torque axis of every table that uses it: edit with care Evidence: ledger:E0706, ledger:E0834</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E422" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x903" flags="0x0">
    <title>Secondary Air - System Enable / Type</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 0 = secondary air injection disabled (stock H3); non-zero enables the AIR controller (1 selects the single-stage pump logic). Only scan-tool output control can command AIR while it is 0. Secondary air injection is disabled on the stock H3 (E0836). Effect: secondary air injection; keep stock unless the AIR hardware is fitted Evidence: ledger:E0836</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2C9F6" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>code</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x904" flags="0x0">
    <title>Secondary Air - Channel Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of AIR channels the controller runs. Stock 1. Secondary air injection is disabled on the stock H3 (E0836). Effect: secondary air injection; keep stock unless the AIR hardware is fitted Evidence: ledger:E0836</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2C9F7" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>channels</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x905" flags="0x30">
    <title>Secondary Air - Channel On Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per channel: time after the AIR system is enabled before that channel is commanded on. Stock 1.3 s. Secondary air injection is disabled on the stock H3 (E0836). Effect: secondary air injection; keep stock unless the AIR hardware is fitted Evidence: ledger:E0836</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>AIR channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C9FB" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>12.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x906" flags="0x30">
    <title>Secondary Air - Channel Off Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per channel: time after the AIR system is no longer enabled before that channel is commanded off. Stock 0 s. Secondary air injection is disabled on the stock H3 (E0836). Effect: secondary air injection; keep stock unless the AIR hardware is fitted Evidence: ledger:E0836</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>AIR channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C9FD" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>12.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x907" flags="0x0">
    <title>Cam Phaser Stuck Response - Pulse Repeats</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phaser stuck response: when the cam is commanded to at least 4 degrees but has not moved past 1.5 degrees (or on a second internal trigger), the PCM pulses the phaser solenoid: stage 1 duty for the stage 1 time, then stage 2 duty for the stage 2 time, repeated up to the pulse repeat count. This is how many pulses one stuck event gets. Stock 12. Effect: raise = more unsticking pulses per event Evidence: ledger:E0837</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22C9D" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x908" flags="0x0">
    <title>Cam Phaser Stuck Response - Minimum Commanded Angle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phaser stuck response (see the stuck response duty and time items): it starts when the cam is commanded to at least the minimum desired angle while the actual angle is at or below the maximum actual angle, and stops pulsing once the actual angle moves past that maximum. This is the minimum commanded angle. Stock 4.0 degrees. Effect: raise = the response needs a larger commanded angle Evidence: ledger:E0837, ledger:E0840</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22CFC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x909" flags="0x0">
    <title>Cam Phaser Stuck Response - Maximum Actual Angle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phaser stuck response (see the stuck response duty and time items): it starts when the cam is commanded to at least the minimum desired angle while the actual angle is at or below the maximum actual angle, and stops pulsing once the actual angle moves past that maximum. This is the maximum actual angle that still counts as stuck. Stock 1.5 degrees. Effect: raise = the phaser counts as stuck over a wider range Evidence: ledger:E0837, ledger:E0840</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22CFE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x90A" flags="0x0">
    <title>Tip-In Torque Ramp - Fast Step Slip Trigger</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. The fast step also starts once gearbox slip exceeds this. Stock 50 rpm. Effect: tip-in torque management Evidence: ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2152C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x90B" flags="0x0">
    <title>Tip-In Torque Ramp - Lash Step Slip Trigger</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. The lash step is used while gearbox slip exceeds this. Stock 10 rpm. Effect: tip-in torque management Evidence: ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21526" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x90C" flags="0x0">
    <title>Tip-In Arming - Slip Threshold B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only) can only arm while the engine is turning less than a set amount faster than the transmission output implies in the current gear (torque converter plus gearbox slip). Below Threshold A it can arm; from Threshold A up to Threshold B it can arm only while engine torque is below the arm torque; at or above Threshold B it cannot arm. Once armed at closed throttle, opening the throttle starts the tip-in torque ramp. Stock both 250 rpm, so there is no in-between band. This is Threshold B. Effect: raise above Threshold A = opens a band where arming depends on engine torque Evidence: ledger:E0356, le...</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21528" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x90D" flags="0x0">
    <title>VE Transient Mode - RPM Band Split</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow source switching: the PCM normally uses the MAF airflow and, during a manifold pressure transient, switches to the VE (speed density) airflow times a learned MAF to VE ratio. It switches over when MAP keeps moving by more than the MAP change threshold per update (two updates in a row), or when MAP moves more than that over two updates while the throttle area moves the same way by more than the area change threshold; it switches back once the MAP change over one, two and three updates is at or below the MAP change threshold. The high band thresholds apply at or above the MAP split or the RPM split. At or above this eng...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x90E" flags="0x0">
    <title>VE Transient Mode - MAP Change Threshold (Low Band)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow source switching: the PCM normally uses the MAF airflow and, during a manifold pressure transient, switches to the VE (speed density) airflow times a learned MAF to VE ratio. It switches over when MAP keeps moving by more than the MAP change threshold per update (two updates in a row), or when MAP moves more than that over two updates while the throttle area moves the same way by more than the area change threshold; it switches back once the MAP change over one, two and three updates is at or below the MAP change threshold. The high band thresholds apply at or above the MAP split or the RPM split. MAP change per updat...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x90F" flags="0x0">
    <title>VE Transient Mode - MAP Change Threshold (High Band)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow source switching: the PCM normally uses the MAF airflow and, during a manifold pressure transient, switches to the VE (speed density) airflow times a learned MAF to VE ratio. It switches over when MAP keeps moving by more than the MAP change threshold per update (two updates in a row), or when MAP moves more than that over two updates while the throttle area moves the same way by more than the area change threshold; it switches back once the MAP change over one, two and three updates is at or below the MAP change threshold. The high band thresholds apply at or above the MAP split or the RPM split. MAP change per updat...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x910" flags="0x0">
    <title>VE Transient Mode - Throttle Area Change Threshold (Low Band)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow source switching: the PCM normally uses the MAF airflow and, during a manifold pressure transient, switches to the VE (speed density) airflow times a learned MAF to VE ratio. It switches over when MAP keeps moving by more than the MAP change threshold per update (two updates in a row), or when MAP moves more than that over two updates while the throttle area moves the same way by more than the area change threshold; it switches back once the MAP change over one, two and three updates is at or below the MAP change threshold. The high band thresholds apply at or above the MAP split or the RPM split. Throttle area change...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4D4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>399.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x911" flags="0x0">
    <title>VE Transient Mode - Throttle Area Change Threshold (High Band)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow source switching: the PCM normally uses the MAF airflow and, during a manifold pressure transient, switches to the VE (speed density) airflow times a learned MAF to VE ratio. It switches over when MAP keeps moving by more than the MAP change threshold per update (two updates in a row), or when MAP moves more than that over two updates while the throttle area moves the same way by more than the area change threshold; it switches back once the MAP change over one, two and three updates is at or below the MAP change threshold. The high band thresholds apply at or above the MAP split or the RPM split. Throttle area change...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4D6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>399.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x912" flags="0x0">
    <title>TCC Slip On Target - Exit Margin</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 10 rpm. The PCM drops back to above target when slip stays more than the exit margin above the target for the exit time. With the converter clutch applied the PCM runs one of two phases: on target (slip held close to the slip target) and above target (slip higher than the target, being pulled back in). Effect: raise = more slip is tolerated before leaving on target Evidence: ledger:E0855</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D442" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x913" flags="0x0">
    <title>TCC Slip On Target - Exit Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 1 s. The PCM drops back to above target when slip stays more than the exit margin above the target for the exit time. With the converter clutch applied the PCM runs one of two phases: on target (slip held close to the slip target) and above target (slip higher than the target, being pulled back in). Effect: raise = slip must stay high longer before leaving on target Evidence: ledger:E0855</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D434" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x914" flags="0x0">
    <title>Engine Displacement</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM turns cylinder airmass into engine load by dividing it by the ideal charge of one cylinder (at barometric pressure, and at 105 kPa and -40 C), worked out from this displacement for 5 cylinders. It also sets the cranking airmass (cranking VE x MAP x cylinder volume / charge temperature). Set this to the engine&#x27;s real displacement after a bore or stroke change. Stock 3.5 L. The PCM cannot represent more than about 5.8 L here. Effect: raise = the same airmass reads as a lower engine load Evidence: ledger:E0217, ledger:E0860, ledger:E0861</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2B1E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>L</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>9.999847</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/6553.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x915" flags="0x0">
    <title>Ideal Cylinder Charge Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM turns cylinder airmass into engine load by dividing it by the ideal charge of one cylinder (at barometric pressure, and at 105 kPa and -40 C), worked out from this displacement for 5 cylinders. This multiplies the ideal charge worked out from the displacement. Stock 1.0. Effect: raise = the same airmass reads as a lower engine load Evidence: ledger:E0217, ledger:E0860</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2B1E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x916" flags="0x0">
    <title>Burst Knock Retard Multiplier - Step Down</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Burst knock retard learned multiplier: two learned multipliers (1.0 = full burst retard) scale the burst knock retard. One event raises the active multiplier by the step up, another lowers it by the step down, and it is never allowed below the floor. Stock floor is 1.0, the top of the range, so on the stock calibration the multipliers stay at 1.0 and nothing is learned; lowering the floor lets burst retard learn down. This is the step down. Stock 0.03. Effect: raise = the multiplier falls faster (only below a lowered floor) Evidence: ledger:E0869</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AD8A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x917" flags="0x0">
    <title>Burst Knock Retard Multiplier - Reset Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Burst knock retard learned multiplier: two learned multipliers (1.0 = full burst retard) scale the burst knock retard. One event raises the active multiplier by the step up, another lowers it by the step down, and it is never allowed below the floor. Stock floor is 1.0, the top of the range, so on the stock calibration the multipliers stay at 1.0 and nothing is learned; lowering the floor lets burst retard learn down. Value both multipliers are set to after a fault reset. Stock 1.0. Effect: sets where learning restarts after a reset Evidence: ledger:E0869</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AD90" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x918" flags="0x0">
    <title>Burst Knock Retard - Hold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Burst knock retard sequence: a quick rise in cylinder airmass starts a burst of spark retard (sized by the burst retard curves and the learned multiplier). After the delay the retard is applied, held for the hold count, then removed in equal steps over the decay count. Counts are updates of the burst retard routine. This is how long the full retard is held. Stock 5 updates. Effect: raise = full burst retard is held longer Evidence: ledger:E0870</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AD6E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x919" flags="0x0">
    <title>Burst Knock Retard - Decay Steps</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Burst knock retard sequence: a quick rise in cylinder airmass starts a burst of spark retard (sized by the burst retard curves and the learned multiplier). After the delay the retard is applied, held for the hold count, then removed in equal steps over the decay count. Counts are updates of the burst retard routine. This is the number of equal steps the retard is removed over. Stock 10 updates. Effect: raise = the burst retard fades out more slowly Evidence: ledger:E0870</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AD70" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x91A" flags="0x0">
    <title>Knock Learn Rate - Engine Speed Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is one of the five weights (relative; only the ratios matter). Stock 0.004. Effect: raise = this curve counts for more in the average Evidence: ledger:E0193, ledger:E0871</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AF0E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x91B" flags="0x0">
    <title>Knock Learn Rate - Coolant Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is one of the five weights (relative; only the ratios matter). Stock 1.0. Effect: raise = this curve counts for more in the average Evidence: ledger:E0193, ledger:E0871</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AF10" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x91C" flags="0x0">
    <title>Knock Learn Rate - Intake Temperature Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is one of the five weights (relative; only the ratios matter). Stock 0.5. Effect: raise = this curve counts for more in the average Evidence: ledger:E0193, ledger:E0871</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AF12" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x91D" flags="0x0">
    <title>Knock Learn Rate - Sample Count Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is one of the five weights (relative; only the ratios matter). Stock 0.125. Effect: raise = this curve counts for more in the average Evidence: ledger:E0193, ledger:E0871</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AF14" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x91E" flags="0x0">
    <title>Load-Based Cam Ramp - Minimum Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Load-based cam phasing: when the load-based cam target takes over, the commanded cam angle ramps toward it by the ramp step each update while throttle is below the throttle limit and vehicle speed is above the speed limit; otherwise it jumps straight to the target. At or below this speed the cam jumps to the target. Stock 10 km/h. Effect: raise = no ramp at low vehicle speed Evidence: ledger:E0358, ledger:E0874</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x23098" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x91F" flags="0x0">
    <title>Load-Based Cam Ramp - Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Load-based cam phasing: when the load-based cam target takes over, the commanded cam angle ramps toward it by the ramp step each update while throttle is below the throttle limit and vehicle speed is above the speed limit; otherwise it jumps straight to the target. Cam angle change per update while ramping. Stock 0.047 deg. Effect: raise = the cam moves to the load target faster Evidence: ledger:E0358, ledger:E0874</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2309A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x920" flags="0x0">
    <title>Cam Target Spark-Limit Reduction - Up Period</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam target reduction while spark is limited: the load-based cam target is multiplied by a factor (1.0 = no change). While spark has been held below its reference spark for half a second, the factor drops by the step down every down period, never below the floor; otherwise it climbs back by the step up every up period. Stock floor is 1.0, so on the stock calibration the factor stays at 1.0. Stock 30 s. Effect: lower = the cam target recovers faster Evidence: ledger:E0720, ledger:E0875</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x23066" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x921" flags="0x0">
    <title>Cam Target Spark-Limit Reduction - Step Down</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam target reduction while spark is limited: the load-based cam target is multiplied by a factor (1.0 = no change). While spark has been held below its reference spark for half a second, the factor drops by the step down every down period, never below the floor; otherwise it climbs back by the step up every up period. Stock floor is 1.0, so on the stock calibration the factor stays at 1.0. Stock 0.0015. Effect: raise = larger reduction each down period Evidence: ledger:E0720, ledger:E0875</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x23068" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x922" flags="0x0">
    <title>Cam Target Spark-Limit Reduction - Step Up</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam target reduction while spark is limited: the load-based cam target is multiplied by a factor (1.0 = no change). While spark has been held below its reference spark for half a second, the factor drops by the step down every down period, never below the floor; otherwise it climbs back by the step up every up period. Stock floor is 1.0, so on the stock calibration the factor stays at 1.0. Stock 0.0015. Effect: raise = larger recovery each up period Evidence: ledger:E0720, ledger:E0875</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2306A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x923" flags="0x0">
    <title>Trans Slip (P0894) Arm - Converter Clutch Command Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 64.999 %. The P0894 (transmission component slipping) test only runs while the converter clutch is applied with its command and pressure held above these minimums, in a gear whose engine to output speed ratio is inside its window, and with its fluid temperature, torque, speed and engine speed windows met. Effect: raise = the test needs a higher clutch command Evidence: ledger:E0849, ledger:E0877</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F722" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x924" flags="0x0">
    <title>Trans Slip (P0894) Arm - Converter Clutch Pressure Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 40 kPa. The P0894 (transmission component slipping) test only runs while the converter clutch is applied with its command and pressure held above these minimums, in a gear whose engine to output speed ratio is inside its window, and with its fluid temperature, torque, speed and engine speed windows met. Effect: raise = the test needs a higher clutch pressure Evidence: ledger:E0849, ledger:E0877</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F740" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x925" flags="0x0">
    <title>Trans Slip (P0894) Arm - 4th Gear Speed Ratio Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed over transmission output speed. Stock 0.475. The P0894 (transmission component slipping) test only runs while the converter clutch is applied with its command and pressure held above these minimums, in a gear whose engine to output speed ratio is inside its window, and with its fluid temperature, torque, speed and engine speed windows met. Effect: raise = the test needs more converter slip in 4th Evidence: ledger:E0849, ledger:E0877</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F724" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x926" flags="0x0">
    <title>Trans Slip (P0894) Arm - 4th Gear Speed Ratio Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed over transmission output speed. Stock 0.98. The P0894 (transmission component slipping) test only runs while the converter clutch is applied with its command and pressure held above these minimums, in a gear whose engine to output speed ratio is inside its window, and with its fluid temperature, torque, speed and engine speed windows met. Effect: lower = the test stops at less converter slip in 4th Evidence: ledger:E0849, ledger:E0877</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F726" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x927" flags="0x0">
    <title>Trans Slip (P0894) Arm - 3rd Gear Speed Ratio Min (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed over transmission output speed. Stock 0.475. 3rd gear is 1.00 to 1, so this window (below 1.00) is never met on stock and the test runs only in 4th. The P0894 (transmission component slipping) test only runs while the converter clutch is applied with its command and pressure held above these minimums, in a gear whose engine to output speed ratio is inside its window, and with its fluid temperature, torque, speed and engine speed windows met. Effect: no effect on stock (inactive) Evidence: ledger:E0849, ledger:E0877</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F728" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x928" flags="0x0">
    <title>Trans Slip (P0894) Arm - 3rd Gear Speed Ratio Max (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed over transmission output speed. Stock 0.98. 3rd gear is 1.00 to 1, so this window (below 1.00) is never met on stock and the test runs only in 4th. The P0894 (transmission component slipping) test only runs while the converter clutch is applied with its command and pressure held above these minimums, in a gear whose engine to output speed ratio is inside its window, and with its fluid temperature, torque, speed and engine speed windows met. Effect: no effect on stock (inactive) Evidence: ledger:E0849, ledger:E0877</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F72A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x929" flags="0x0">
    <title>Trans Slip (P0894) Arm - Converter Clutch Command Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0894 (transmission component slipping) test: time the converter clutch command must stay at or above its minimum before the test arms. Stock 1.75 s. Effect: raise = the test arms later after the clutch is commanded on Evidence: ledger:E1095</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F73C" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x92A" flags="0x0">
    <title>Trans Slip (P0894) Arm - Converter Clutch Pressure Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0894 (transmission component slipping) test: time the converter clutch pressure must stay at or above its minimum before the test arms. Stock 0: no delay. Effect: raise = the test arms later after clutch pressure is up Evidence: ledger:E1095</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F73D" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x92B" flags="0x30">
    <title>Highest Gear by Range Selector Position</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest gear the transmission may command in each range selector position (range code). Stock 2nd, 2nd, 3rd, then 4th: code 0 is manual 1 (its shift schedule holds 1st; this cap is the hard limit), code 1 manual 2, code 2 manual 3, code 3 Drive. Applies in every shift mode stock uses. Effect: lower a code&#x27;s value = that selector position cannot shift above it Evidence: ledger:E0387, ledger:E0396, ledger:E0838, ledger:E0879</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>range code</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="code 0 (1)" />
      <LABEL index="1" value="code 1 (2)" />
      <LABEL index="2" value="code 2 (3)" />
      <LABEL index="3" value="code 3 (D)" />
      <LABEL index="4" value="code 4" />
      <LABEL index="5" value="code 5" />
      <LABEL index="6" value="code 6" />
      <LABEL index="7" value="code 7" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x394DC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gear</units>
      <decimalpl>0</decimalpl>
      <min>1.000000</min>
      <max>65536.000000</max>
      <MATH equation="X+1"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x92C" flags="0x0">
    <title>Coolant Hot Shift Mode - Clear Below (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine coolant temperature below which the coolant-hot shift mode ends. Stock 250 C: the mode is never entered on stock. Effect: no effect on stock (inactive) Evidence: ledger:E0838, ledger:E0879</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DD36" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x92D" flags="0x0">
    <title>Coolant Hot Shift Mode - Set Above (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine coolant temperature above which the coolant-hot shift mode starts (only with the pedal above the high pedal point). Stock 255 C: never reached. Effect: no effect on stock (inactive) Evidence: ledger:E0838, ledger:E0879</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DD38" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x92E" flags="0x0">
    <title>TCC Slip On Target - Re-Entry Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 2 s. After the converter clutch leaves on target (slip back above target), the PCM keeps it in the above-target phase at least this long before it can return to on target. With the converter clutch applied the PCM runs one of two phases: on target (slip held close to the slip target) and above target (slip higher than the target, being pulled back in). Effect: raise = a longer wait before on-target control resumes Evidence: ledger:E0855, ledger:E0880</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D436" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x92F" flags="0x30">
    <title>O2 Response Test - Reversal Tolerance, Lean to Rich</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A drop larger than this during a lean-to-rich transition discards that transition. Stock 5 mV. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: changes what the O2 response test measures Evidence: ledger:E0281, ledger:E0295, ledger:E0902</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (bank 1)" />
      <LABEL index="1" value="second sensor (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C7A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x930" flags="0x30">
    <title>O2 Response Test - Reversal Tolerance, Rich to Lean</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A rise larger than this during a rich-to-lean transition discards that transition. Stock 5 mV. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: changes what the O2 response test measures Evidence: ledger:E0281, ledger:E0295, ledger:E0902</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (bank 1)" />
      <LABEL index="1" value="second sensor (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C7E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x931" flags="0x30">
    <title>O2 Response Test - Transition Timing Low Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower end of the transition timing window (transitions are timed between this and the high voltage). Stock 350 mV. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: changes what the O2 response test measures Evidence: ledger:E0281, ledger:E0295, ledger:E0902</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (bank 1)" />
      <LABEL index="1" value="second sensor (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C82" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x932" flags="0x30">
    <title>O2 Response Test - Transition Timing High Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper end of the transition timing window. Stock 650 mV. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: changes what the O2 response test measures Evidence: ledger:E0281, ledger:E0295, ledger:E0902</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (bank 1)" />
      <LABEL index="1" value="second sensor (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C86" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x933" flags="0x30">
    <title>O2 Response Test - Lean Switch Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Falling to this or below counts a lean switch. Stock 500 mV. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: changes what the O2 response test measures Evidence: ledger:E0281, ledger:E0295, ledger:E0902</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (bank 1)" />
      <LABEL index="1" value="second sensor (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C8A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x934" flags="0x30">
    <title>O2 Response Test - Rich Switch Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rising to this or above counts a rich switch. Stock 600 mV. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: changes what the O2 response test measures Evidence: ledger:E0281, ledger:E0295, ledger:E0902</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (bank 1)" />
      <LABEL index="1" value="second sensor (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34C8E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x935" flags="0x0">
    <title>P0562 Test - Run Condition, Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0562 test only runs while engine speed is at or above this. Stock 1200 rpm. Effect: raise = the test needs a higher engine speed to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20934" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x936" flags="0x0">
    <title>P0068 Test - Run Condition, Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0068 test only runs while engine speed is above this. Stock 800 rpm. Effect: raise = the test needs a higher engine speed to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B36" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x937" flags="0x0">
    <title>P0325 Test - Run Condition, Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0325 test only runs while engine speed is above this. Stock 1800 rpm. Effect: raise = the test needs a higher engine speed to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32644" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x938" flags="0x0">
    <title>P0325 Test - Run Condition, Engine Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0325 test only runs while engine speed is below this. Stock 6400 rpm. Effect: lower = the test needs a lower engine speed to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32646" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x939" flags="0x0">
    <title>P0327 / P0332 Test - Run Condition, Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0327 / P0332 test only runs while engine speed is above this. Stock 1800 rpm. Effect: raise = the test needs a higher engine speed to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32648" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x93A" flags="0x0">
    <title>P0116 Test - Startup Coolant Pass Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or below this startup coolant temperature the P0116 test reports a pass at once and skips its warm-up checks (the startup coolant high limit is still checked first). Above it the warm-up checks run. Stock 15 degC. Effect: raise = more cold starts pass P0116 without the warm-up checks Evidence: ledger:E0906, ledger:E0912</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x336EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x93B" flags="0x0">
    <title>P0522 / P0523 Test - Run Condition, System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0522 / P0523 test only runs while system voltage is at or above this. Stock 11 V. Effect: raise = the test needs a higher system voltage to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3471C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x93C" flags="0x0">
    <title>P0326 Test - Run Condition, Manifold Pressure Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0326 test only runs while manifold pressure is at or above this. Stock 55 kPa. Effect: raise = the test needs a higher manifold pressure to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x93D" flags="0x0">
    <title>P1380 / P1381 Test - Run Condition, Vehicle Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P1380 / P1381 test only runs while vehicle speed is at or above this. Stock 5 km/h. Effect: raise = the test needs a higher vehicle speed to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x93E" flags="0x0">
    <title>P0563 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0563 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 6. Effect: raise = P0563 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2092E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x93F" flags="0x0">
    <title>P0562 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0562 sets once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 6. Effect: raise = P0562 needs more samples before it sets Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20936" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x940" flags="0x0">
    <title>P0562 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0562 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 6. Effect: raise = P0562 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20938" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x941" flags="0x0">
    <title>P0856 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0856 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 30. Effect: raise = P0856 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20952" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x942" flags="0x0">
    <title>P0117 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0117 reports a pass once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 100. Effect: raise = P0117 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x943" flags="0x0">
    <title>P1114 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1114 reports a pass once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 2000. Effect: raise = P1114 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x944" flags="0x0">
    <title>P0118 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0118 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 100. Effect: raise = P0118 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337D4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x945" flags="0x0">
    <title>P1115 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1115 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 2000. Effect: raise = P1115 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x337D6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x946" flags="0x0">
    <title>P0442 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0442 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 6. Effect: raise = P0442 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D10" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x947" flags="0x0">
    <title>P0451 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0451 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 6. Effect: raise = P0451 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33D1C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x948" flags="0x0">
    <title>P0453 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0453 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 100. Effect: raise = P0453 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35816" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x949" flags="0x0">
    <title>P0452 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0452 sets once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 80. Effect: raise = P0452 needs more samples before it sets Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35818" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x94A" flags="0x0">
    <title>P0452 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0452 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 100. Effect: raise = P0452 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3581A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x94B" flags="0x0">
    <title>P2027 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2027 reports a pass once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 100. Effect: raise = P2027 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F56" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x94C" flags="0x0">
    <title>P2026 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2026 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 100. Effect: raise = P2026 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F5A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x94D" flags="0x0">
    <title>P0113 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0113 reports a pass once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 100. Effect: raise = P0113 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36544" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x94E" flags="0x0">
    <title>P1111 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1111 reports a pass once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 2000. Effect: raise = P1111 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36546" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x94F" flags="0x0">
    <title>P0326 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0326 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 80. Effect: raise = P0326 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x950" flags="0x0">
    <title>P2610 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2610 sets once this count is reached. The count goes up by one each time the test runs. Stock 3. Effect: raise = P2610 needs more samples before it sets Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3751A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x951" flags="0x0">
    <title>P0563 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0563 sets once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 6. Effect: raise = P0563 needs more samples before it sets Evidence: ledger:E0909</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2092C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x952" flags="0x0">
    <title>P250A Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P250A reports a pass once the test has run with its condition met for this long. Stock 30 s. Effect: raise = P250A takes longer to pass Evidence: ledger:E0909, ledger:E0958</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23158" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x953" flags="0x0">
    <title>P0068 Fail - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0068 sets once its fault condition has been present without a break for this long. Stock 0.19 s. Effect: raise = the fault must last longer before P0068 sets Evidence: ledger:E0909, ledger:E1041</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B20" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x954" flags="0x0">
    <title>P0520 Fail - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0520 sets once its fault has been present for this long. Stock 5 s. Effect: raise = the fault must last longer before P0520 sets Evidence: ledger:E0909, ledger:E1041</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3471A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x955" flags="0x0">
    <title>P0336 Pass - Window Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0336 (P0386 / P1372 in the other cam modes) reports a pass when a test window of this length ends without the fail count being reached. Stock 25 s. Effect: raise = each test window is longer Evidence: ledger:E0909, ledger:E1041</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34CC6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x956" flags="0x0">
    <title>P0453 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0453 sets once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 80. Effect: raise = P0453 needs more samples before it sets Evidence: ledger:E0909</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35814" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x957" flags="0x0">
    <title>P0462 Fail - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0462 (fuel level sensor circuit low) sets once the sender has read below its low threshold for this long without returning to the normal range. Stock 60 s. Effect: raise = P0462 takes longer to set Evidence: ledger:E0909, ledger:E0957</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x364BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x958" flags="0x0">
    <title>P0112 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0112 reports a pass once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 100. Effect: raise = P0112 needs more samples before it passes Evidence: ledger:E0909</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3653C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x959" flags="0x0">
    <title>P1112 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1112 reports a pass once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 2000. Effect: raise = P1112 needs more samples before it passes Evidence: ledger:E0909</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3653E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x95A" flags="0x0">
    <title>P0326 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0326 sets once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 40. Effect: raise = P0326 needs more samples before it sets Evidence: ledger:E0909</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x95B" flags="0x0">
    <title>P0101 / P0106 / P0121 / P1101 Test - Run Condition, Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0101 / P0106 / P0121 / P1101 tests only run while engine speed is at or above this. Stock 400 rpm. Effect: raise = the test needs a higher engine speed to run Evidence: ledger:E0909</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x95C" flags="0x0">
    <title>P0135 / P0141 Check - Fail Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater check (P0135 upstream, P0141 downstream): the code sets once more than this many samples in a test are outside the allowed range. Stock 45. Effect: raise = more out of range samples are needed to set a heater code Evidence: ledger:E0909, ledger:E0996</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34BBE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x95D" flags="0x0">
    <title>P0622 Fail - Time, Engine Stopped</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0622 (generator field control circuit) key-on, engine-stopped check: P0622 sets once the check has run with engine speed at 0 and the field signal at or below its limit for this long. Stock 5 s. Effect: raise = the engine-stopped check takes longer to set P0622 Evidence: ledger:E0913, ledger:E0958</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2082E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x95E" flags="0x0">
    <title>P0622 Fail - Time, Engine Running</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0622 (generator field control circuit) engine-running check: P0622 sets once the check has run with the engine running and the field signal at or above its limit for this long. Stock 30 s. Effect: raise = the engine-running check takes longer to set P0622 Evidence: ledger:E0913, ledger:E0958</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20830" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x95F" flags="0x0">
    <title>P0503 Test - Time Since Transfer Case Range Change</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): the check runs only this long after the last transfer case range change. Stock 2 s. Effect: raise = the check waits longer after a range change Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F848" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x960" flags="0x0">
    <title>Fuel Trim Monitor Enable - Coolant Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while coolant temperature is above this. Stock -35 C. Narrowing the window makes the monitor run less often. Effect: raise = the monitor needs a warmer engine to run Evidence: ledger:E0971</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x961" flags="0x0">
    <title>Fuel Trim Monitor Enable - Coolant Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while coolant temperature is below this. Stock 125 C. Narrowing the window makes the monitor run less often. Effect: lower = the monitor stops at a lower coolant temperature Evidence: ledger:E0971</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x962" flags="0x0">
    <title>Fuel Trim Monitor Enable - Airflow Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while mass airflow is above this. Stock 1 g/s. Narrowing the window makes the monitor run less often. Effect: raise = the monitor needs more airflow to run Evidence: ledger:E0971</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3628A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x963" flags="0x0">
    <title>Fuel Trim Monitor Enable - Airflow Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while mass airflow is below this. Stock 511 g/s (no limit in practice). Narrowing the window makes the monitor run less often. Effect: lower = the monitor stops at a lower airflow Evidence: ledger:E0971</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36288" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x964" flags="0x0">
    <title>Fuel Trim Monitor Enable - Intake Air Temperature Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while intake air temperature is below this. Stock 145 C (no limit in practice). Narrowing the window makes the monitor run less often. Effect: lower = the monitor stops at a lower intake air temperature Evidence: ledger:E0971</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362D6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x965" flags="0x0">
    <title>Fuel Trim Monitor Enable - Vehicle Speed Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while vehicle speed is below this. Stock 132 km/h. Narrowing the window makes the monitor run less often. Effect: lower = the monitor stops at a lower speed Evidence: ledger:E0971</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x362EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x966" flags="0x0">
    <title>Fuel Trim Monitor Stage Enable - Airflow Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. One of the fuel trim monitor&#x27;s (P0171 system too lean, P0172 system too rich) conditions for running its test stages: mass airflow must be above this. Stock 2 g/s. Narrowing the window makes the monitor run less often. Effect: raise = the monitor&#x27;s stages need more airflow to run Evidence: ledger:E0971</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3628E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x967" flags="0x0">
    <title>Fuel Trim Monitor Stage Enable - Airflow Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. One of the fuel trim monitor&#x27;s (P0171 system too lean, P0172 system too rich) conditions for running its test stages: mass airflow must be below this. Stock 511 g/s (no limit in practice). Narrowing the window makes the monitor run less often. Effect: lower = the monitor&#x27;s stages stop at a lower airflow Evidence: ledger:E0971</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3628C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x968" flags="0x0">
    <title>Transmission Diagnostics Enable - Engine Speed Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most transmission diagnostics (fluid temperature sensor, turbine speed, pressure switch, TCC and gear ratio tests) only run once engine speed has stayed at or above this (and at or below the high limit) for the engine run time below. Stock 450 rpm. Effect: raise = transmission diagnostics need a higher engine speed to run Evidence: ledger:E0976</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F8C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x969" flags="0x0">
    <title>Transmission Diagnostics Enable - Engine Speed High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most transmission diagnostics (fluid temperature sensor, turbine speed, pressure switch, TCC and gear ratio tests) only run once engine speed has stayed at or below this (and at or above the low limit) for the engine run time below. Stock 6200 rpm. Effect: lower = transmission diagnostics stop at a lower engine speed Evidence: ledger:E0976</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F8CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x96A" flags="0x0">
    <title>Transmission Diagnostics Enable - Engine Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most transmission diagnostics (fluid temperature sensor, turbine speed, pressure switch, TCC and gear ratio tests) only run once engine speed has stayed inside its enable range for this long. Stock 7.0 s. Effect: raise = transmission diagnostics start later after the engine starts Evidence: ledger:E0976</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F8C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x96B" flags="0x0">
    <title>Transmission Diagnostics Enable - Output Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most transmission diagnostics (fluid temperature sensor, turbine speed, pressure switch, TCC and gear ratio tests) only run once transmission output speed has stayed at or below this for the time below. Stock 200 km/h. Effect: lower = transmission diagnostics stop at a lower speed Evidence: ledger:E0976</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F8CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x96C" flags="0x0">
    <title>Transmission Diagnostics Enable - Output Speed Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most transmission diagnostics (fluid temperature sensor, turbine speed, pressure switch, TCC and gear ratio tests) only run once transmission output speed has stayed at or below its maximum for this long. Stock 5.0 s. Effect: raise = transmission diagnostics start later Evidence: ledger:E0976</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F8CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x96D" flags="0x0">
    <title>Transmission Diagnostics Enable - System Voltage Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most transmission diagnostics (fluid temperature sensor, turbine speed, pressure switch, TCC and gear ratio tests) only run while system voltage is at or above this. Stock 8.0 V. Effect: raise = transmission diagnostics need a higher voltage to run Evidence: ledger:E0977</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F8C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x96E" flags="0x0">
    <title>Transmission Diagnostics Enable - System Voltage High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most transmission diagnostics (fluid temperature sensor, turbine speed, pressure switch, TCC and gear ratio tests) only run while system voltage is at or below this. Stock 18.0 V. Effect: lower = transmission diagnostics stop at a lower voltage Evidence: ledger:E0977</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F8C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x96F" flags="0x0">
    <title>Ignition On Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM treats the ignition as switched on once system voltage has been above this on two updates in a row; the engine start logic and many diagnostics wait for it. Stock 6.0 V. Effect: raise = the PCM needs more voltage before it treats the key as on (too high can stop the engine starting) Evidence: ledger:E0978</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20942" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x970" flags="0x0">
    <title>Ignition Off Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the ignition is treated as on, the PCM treats it as off again when system voltage drops to or below this. Stock 2.0 V. Effect: raise = the PCM treats a voltage dip as key off sooner Evidence: ledger:E0978</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20940" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x971" flags="0x0">
    <title>P0711 - Start Values Capture Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0711 (transmission fluid temperature sensor range / performance): the fluid and coolant temperatures &#x27;at engine start&#x27; that the stuck-sensor checks compare against keep updating until the engine has run this long. Stock 35 s. Effect: raise = the start values are taken later after the engine starts Evidence: ledger:E0911, ledger:E0979</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7D4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x972" flags="0x0">
    <title>P0711 - Pass Temperature Change</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0711 (transmission fluid temperature sensor range / performance): the check counts toward a pass once the fluid temperature has moved at least this far from its start value. Stock 2.5 C. Effect: raise = the fluid temperature must change more before the check passes Evidence: ledger:E0911, ledger:E0979</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x973" flags="0x0">
    <title>P0711 - Pass Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0711 (transmission fluid temperature sensor range / performance): the check reports a pass once the fluid temperature has stayed at least the pass change away from its start value for this long. Stock 5 s. Effect: raise = the check takes longer to pass Evidence: ledger:E0911, ledger:E0979</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7D1" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x974" flags="0x0">
    <title>P1816 Test - Output Speed Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1816 check, alternative run condition path: lowest output speed. Stock 250 rpm. The alternative path is not used on this truck, so this value has no effect. Effect: no effect on this truck Evidence: ledger:E0981, ledger:E1101</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F888" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x975" flags="0x0">
    <title>P1816 Test - Run Condition, Throttle Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1816 (fluid pressure switch reads park / neutral in 4th gear) check: the check runs (4th gear, converter clutch applied) only with driver throttle at or below this. Stock 100 %: no upper limit. Effect: lower = the check stops at less throttle Evidence: ledger:E0981, ledger:E1101</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F88A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x976" flags="0x0">
    <title>P1816 Test - Run Condition, Speed Ratio Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1816 (fluid pressure switch reads park / neutral in 4th gear) check: the check runs (4th gear, converter clutch applied) only with the transmission speed ratio at or above this. Stock 0.600. Effect: raise = the check needs a higher ratio Evidence: ledger:E0981, ledger:E1101</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F894" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x977" flags="0x0">
    <title>P1816 Test - Run Condition, Speed Ratio Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1816 (fluid pressure switch reads park / neutral in 4th gear) check: the check runs (4th gear, converter clutch applied) only with the transmission speed ratio at or below this. Stock 1.580. Effect: lower = the check needs a lower ratio Evidence: ledger:E0981, ledger:E1101</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F896" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x978" flags="0x0">
    <title>IAT Sensor High Test (P0113) Enable - Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The intake air temperature sensor circuit-high checks (P0113, P1111) only run while coolant temperature is at or above this. Stock 50 C. Effect: raise = the check needs a warmer engine to run Evidence: ledger:E0983</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3654A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x979" flags="0x0">
    <title>IAT Sensor High Test (P0113) Enable - Airflow Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The intake air temperature sensor circuit-high checks (P0113, P1111) only run while mass airflow is below this. Stock 12 g/s. Effect: lower = the check only runs at lower airflow Evidence: ledger:E0983</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3654C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x97A" flags="0x0">
    <title>IAT Sensor High Test (P0113) Enable - Vehicle Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The intake air temperature sensor circuit-high checks (P0113, P1111) only run while vehicle speed is below this. Stock 1.6 km/h (stopped). Effect: raise = the check also runs while moving slowly Evidence: ledger:E0983</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3654E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x97B" flags="0x0">
    <title>IAT Sensor Low Test (P0112) Enable - Coolant Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The intake air temperature sensor circuit-low checks (P0112, P1112) only run while coolant temperature is below this. Stock 110 C. Effect: lower = the check stops at a lower coolant temperature Evidence: ledger:E0983</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36550" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x97C" flags="0x0">
    <title>IAT Sensor Low Test (P0112) Enable - Vehicle Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The intake air temperature sensor circuit-low checks (P0112, P1112) only run while vehicle speed is at or above this. Stock 40.2 km/h. Effect: raise = the check needs a higher speed to run Evidence: ledger:E0983</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36552" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x97D" flags="0x0">
    <title>Catalyst Monitor Enable - Barometric Pressure Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only arms while barometric pressure is above this. Stock 68 kPa. Effect: lower = the test can arm at higher altitude Evidence: ledger:E0984, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328D8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x97E" flags="0x0">
    <title>Catalyst Monitor Enable - Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only arms while coolant temperature is at or above this. Stock 69 C. Effect: lower = the test can arm on a cooler engine Evidence: ledger:E0984, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328DA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x97F" flags="0x0">
    <title>Catalyst Monitor Enable - Coolant Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only arms while coolant temperature is at or below this. Stock 125 C. Effect: raise = the test can arm on a hotter engine Evidence: ledger:E0984, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328DC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x980" flags="0x0">
    <title>Catalyst Monitor Enable - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only arms while system voltage is above this. Stock 9.0 V. Effect: raise = the test needs a higher voltage to arm Evidence: ledger:E0984, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328DE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x981" flags="0x0">
    <title>Idle Speed Diagnostic Enable - Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle speed diagnostic (P0506 idle rpm lower than expected, P0507 higher than expected) only runs while coolant temperature is at or above this. Stock -7 C. Effect: raise = the diagnostic needs a warmer engine to run Evidence: ledger:E0985</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x982" flags="0x0">
    <title>Idle Speed Diagnostic Enable - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle speed diagnostic (P0506 idle rpm lower than expected, P0507 higher than expected) only runs while the engine has run at least this long since start. Stock 100 s. Effect: raise = the diagnostic starts later after a start Evidence: ledger:E0985</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x983" flags="0x0">
    <title>Idle Speed Diagnostic Enable - Intake Air Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle speed diagnostic (P0506 idle rpm lower than expected, P0507 higher than expected) only runs while intake air temperature is at or above this. Stock -7 C. Effect: raise = the diagnostic needs warmer intake air to run Evidence: ledger:E0985</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x984" flags="0x0">
    <title>Idle Speed Diagnostic Enable - System Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle speed diagnostic (P0506 idle rpm lower than expected, P0507 higher than expected) only runs while system voltage is at or below this. Stock 18.0 V. Effect: lower = the diagnostic stops at a lower voltage Evidence: ledger:E0985</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x985" flags="0x0">
    <title>Idle Speed Diagnostic Enable - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle speed diagnostic (P0506 idle rpm lower than expected, P0507 higher than expected) only runs while system voltage is at or above this. Stock 11.0 V. Effect: raise = the diagnostic needs a higher voltage to run Evidence: ledger:E0985</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x986" flags="0x0">
    <title>Idle Speed Diagnostic - Arm Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle speed diagnostic (P0506, P0507) starts checking only after its enable conditions, idle mode and the speed limit have all held for this long. Stock 2.0 s. Effect: raise = the diagnostic starts checking later Evidence: ledger:E0985</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365BC" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x987" flags="0x0">
    <title>Idle Speed Diagnostic Enable - Vehicle Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle speed diagnostic (P0506 idle rpm lower than expected, P0507 higher than expected) only runs while vehicle speed is at or below this. Stock 5 km/h. Effect: raise = the diagnostic also runs while rolling faster Evidence: ledger:E0985</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x988" flags="0x0">
    <title>Fuel Level Sensor Checks Enable - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel level sensor checks (P0461 range / performance, P0462 circuit low, P0463 circuit high) only run while system voltage is above this. Stock 11.0 V. Effect: raise = the checks need a higher voltage to run Evidence: ledger:E0986</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x364C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x989" flags="0x0">
    <title>Fuel Level Sensor Checks Enable - System Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel level sensor checks (P0461 range / performance, P0462 circuit low, P0463 circuit high) only run while system voltage is below this. Stock 18.0 V. Effect: lower = the checks stop at a lower voltage Evidence: ledger:E0986</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x364C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x98A" flags="0x30">
    <title>Knock Detection - Reference Level Filter by Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: share of the gap to the newest sample that the reference level of a cylinder closes at each of its knock windows, in steady running, in a rising transient and in a falling transient. The knock threshold is added to this level. Stock 1.0 in all three: the reference is simply the last sample of that cylinder. Effect: lower = the reference level is smoothed over more knock windows Evidence: ledger:E1138</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>knock detection mode</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="steady" />
      <LABEL index="1" value="rising transient" />
      <LABEL index="2" value="falling transient" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31D20" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x98B" flags="0x30">
    <title>Knock Detection - Noise Level Filter by Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: share of the gap to the newest sample that the noise level of a cylinder closes at each of its knock windows, in steady running, in a rising transient and in a falling transient. The noise level drives the knock sensor amplifier gain. Stock 0.1 steady and 0.2 in transients. Effect: raise = the noise level follows the sensor signal faster Evidence: ledger:E1138</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>knock detection mode</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="steady" />
      <LABEL index="1" value="rising transient" />
      <LABEL index="2" value="falling transient" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31D26" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x98C" flags="0x30">
    <title>Tip-In Spark Advance - Trigger Factor vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in spark advance (spark advance added for a short time when cylinder airmass jumps): the advance triggers when cylinder airmass rises in one 12.5 ms pass by at least 1.024 g per cylinder x the three trigger factors (engine speed, coolant, throttle). This is the engine speed factor. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: lower = the advance triggers on a smaller airmass jump Evidence: ledger:E1142</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CBB6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x98D" flags="0x30">
    <title>Tip-In Spark Advance - Trigger Factor vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in spark advance (spark advance added for a short time when cylinder airmass jumps): the advance triggers when cylinder airmass rises in one 12.5 ms pass by at least 1.024 g per cylinder x the three trigger factors (engine speed, coolant, throttle). This is the coolant factor. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: lower = the advance triggers on a smaller airmass jump Evidence: ledger:E1142</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CBDA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x98E" flags="0x0">
    <title>Torque State - Torque Filter Coefficient</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of the change in the engine torque term taken into its filtered value each update (stock 0.25). The filtered value decides the torque state (high or low) that picks the shift pressure tables and gates shift adapt learning. Effect: raise = the torque state reacts faster Evidence: ledger:E0350, ledger:E1394</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38ABA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x98F" flags="0x30">
    <title>Torque State - In-Shift Torque Threshold by Upshift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During an upshift the torque state is high when the filtered engine torque is at or above this (stock 0 for all three, so it is high unless the torque is negative). The torque state picks the shift pressure tables. Effect: raise = more torque needed for the high torque state during upshifts Evidence: ledger:E0350, ledger:E0917, ledger:E1417</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38ABC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x990" flags="0x30">
    <title>Torque Band - Shift Torque Adder Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift torque adder breakpoints of the torque band limits (columns). Stock all 0, so only the first column (adder 0 or less) and the last column (adder above 0) are used. Axis data: keep ascending. Effect: spreads the torque band limits over the shift torque adder Evidence: ledger:E0350, ledger:E1268</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38AC4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x991" flags="0x30">
    <title>Torque Band - Upper Torque Limit</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 9][9 words]; COUNT is a structure word. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission torque management: the torque band state is set to high when filtered engine torque is at or above this, by gear and shift torque adder. Between the lower and upper limits the state is in-between. Stock identical to the lower limit (no in-between band). Effect: raise = more torque needed for the high torque band state Evidence: ledger:E0350, ledger:E1268, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="0" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="0" />
      <LABEL index="7" value="0" />
      <LABEL index="8" value="0" />
      <LABEL index="9" value="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38AD6" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x992" flags="0x30">
    <title>Torque Band - Lower Torque Limit</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 9][9 words]; COUNT is a structure word. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission torque management: the torque band state is set to low when filtered engine torque is at or below this, by gear and shift torque adder. Stock identical to the upper limit. Effect: lower = less torque needed for the low torque band state Evidence: ledger:E0350, ledger:E1268, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="0" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="0" />
      <LABEL index="7" value="0" />
      <LABEL index="8" value="0" />
      <LABEL index="9" value="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38B12" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x993" flags="0x30">
    <title>TCC Expected Throttle - Speed Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission speed breakpoints of the three TCC expected throttle tables. Stock 0 to 160 km/h in 10 km/h steps. Dormant: off in this calibration (the feature enable is 0), so it has no effect on this truck&#x27;s software. Effect: moves the speed points of the TCC expected throttle tables Evidence: ledger:E0404, ledger:E1228</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D1DA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x994" flags="0x30">
    <title>TCC Expected Throttle - Cruise, by Gear vs Speed</title>
    <description>Change in small steps and log. Each row is a byte curve [COUNT = 17][TYPE][17 bytes]; COUNT and TYPE are structure bytes. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle demand the converter clutch logic expects in the cruise shift mode, by gear and transmission speed (0 to 160 km/h); it is turned into an expected engine torque with the transmission&#x27;s engine torque map. Stock 98.8 % everywhere. Dormant: off in this calibration (the feature enable is 0), so it has no effect on this truck&#x27;s software. Effect: raise = higher expected throttle for the converter clutch logic in that mode Evidence: ledger:E0404, ledger:E1228, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="2" />
      <LABEL index="4" value="3" />
      <LABEL index="5" value="4" />
      <LABEL index="6" value="5" />
      <LABEL index="7" value="6" />
      <LABEL index="8" value="7" />
      <LABEL index="9" value="8" />
      <LABEL index="10" value="9" />
      <LABEL index="11" value="10" />
      <LABEL index="12" value="11" />
      <LABEL index="13" value="12" />
      <LABEL index="14" value="13" />
      <LABEL index="15" value="14" />
      <LABEL index="16" value="15" />
      <LABEL index="17" value="16" />
      <LABEL index="18" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D290" mmedelementsizebits="8" mmedrowcount="4" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>99.609375</max>
      <MATH equation="X/2.56"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x995" flags="0x30">
    <title>TCC Expected Throttle - 4-Lo, by Gear vs Speed</title>
    <description>Change in small steps and log. Each row is a byte curve [COUNT = 17][TYPE][17 bytes]; COUNT and TYPE are structure bytes. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle demand the converter clutch logic expects in the 4-Lo shift mode, by gear and transmission speed (0 to 160 km/h); it is turned into an expected engine torque with the transmission&#x27;s engine torque map. Stock 98.8 % everywhere. Dormant: off in this calibration (the feature enable is 0), so it has no effect on this truck&#x27;s software. Effect: raise = higher expected throttle for the converter clutch logic in that mode Evidence: ledger:E0404, ledger:E1228, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="2" />
      <LABEL index="4" value="3" />
      <LABEL index="5" value="4" />
      <LABEL index="6" value="5" />
      <LABEL index="7" value="6" />
      <LABEL index="8" value="7" />
      <LABEL index="9" value="8" />
      <LABEL index="10" value="9" />
      <LABEL index="11" value="10" />
      <LABEL index="12" value="11" />
      <LABEL index="13" value="12" />
      <LABEL index="14" value="13" />
      <LABEL index="15" value="14" />
      <LABEL index="16" value="15" />
      <LABEL index="17" value="16" />
      <LABEL index="18" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D2E0" mmedelementsizebits="8" mmedrowcount="4" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>99.609375</max>
      <MATH equation="X/2.56"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x996" flags="0x30">
    <title>TCC Expected Throttle - Normal, by Gear vs Speed</title>
    <description>Change in small steps and log. Each row is a byte curve [COUNT = 17][TYPE][17 bytes]; COUNT and TYPE are structure bytes. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle demand the converter clutch logic expects in the normal shift mode, by gear and transmission speed (0 to 160 km/h); it is turned into an expected engine torque with the transmission&#x27;s engine torque map. Stock 98.8 % everywhere. Dormant: off in this calibration (the feature enable is 0), so it has no effect on this truck&#x27;s software. Effect: raise = higher expected throttle for the converter clutch logic in that mode Evidence: ledger:E0404, ledger:E1228, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="2" />
      <LABEL index="4" value="3" />
      <LABEL index="5" value="4" />
      <LABEL index="6" value="5" />
      <LABEL index="7" value="6" />
      <LABEL index="8" value="7" />
      <LABEL index="9" value="8" />
      <LABEL index="10" value="9" />
      <LABEL index="11" value="10" />
      <LABEL index="12" value="11" />
      <LABEL index="13" value="12" />
      <LABEL index="14" value="13" />
      <LABEL index="15" value="14" />
      <LABEL index="16" value="15" />
      <LABEL index="17" value="16" />
      <LABEL index="18" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D330" mmedelementsizebits="8" mmedrowcount="4" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>99.609375</max>
      <MATH equation="X/2.56"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x997" flags="0x30">
    <title>TCC Apply Pressure - Base vs Torque and Turbine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base pressure command for the torque converter clutch, by filtered engine torque (rows, -20 to 60 Nm) and turbine speed (columns, 1000 to 2800 rpm). An adjustment is added and the result is limited to the TCC full command pressure; it becomes the TCC pressure command. Stock 65 kPa at -20 Nm / 1000 rpm, rising 5 kPa per column and falling 5 kPa per row. Effect: raise = more TCC apply pressure at that torque and turbine speed Evidence: ledger:E0404, ledger:E1267</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3D070" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (turbine speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x3D034" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>9</indexcount>
      <units>Nm (engine torque, filtered)</units>
      <embedinfo type="1" />
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D088" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x998" flags="0x30">
    <title>TCC Apply Pressure - Torque Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque breakpoints (filtered) of the TCC base apply pressure table rows. Axis data: keep ascending. Effect: moves the table&#x27;s torque rows Evidence: ledger:E0404, ledger:E1267</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D034" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x999" flags="0x30">
    <title>TCC Apply Pressure - Turbine Speed Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turbine speed breakpoints of the TCC base apply pressure table columns. Axis data: keep ascending. Effect: moves the table&#x27;s turbine speed columns Evidence: ledger:E0404, ledger:E1267</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D070" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x99A" flags="0x30">
    <title>Shift Adapt - Min Shift Delay by Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A shift is not used for learning when its shift delay is shorter than this (stock 0.25 s 1-2, 0.5 s 2-3, 0 for 3-4). Shift delay is the time from the shift command to the start of the ratio change; shift time is the time the ratio change itself takes. Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Effect: which shifts the adaptive learning uses Evidence: ledger:E0806, ledger:E1029, ledger:E1318</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C25E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x99B" flags="0x30">
    <title>Shift Adapt - Max Shift Delay by Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A shift is not used for learning when its shift delay is longer than this (stock 2.0 s 1-2 and 2-3, 0 for 3-4). Shift delay is the time from the shift command to the start of the ratio change; shift time is the time the ratio change itself takes. Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Effect: which shifts the adaptive learning uses Evidence: ledger:E0806, ledger:E1029, ledger:E1318</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C264" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x99C" flags="0x30">
    <title>Shift Adapt - Min Shift Time by Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A shift is not used for learning when its shift time is shorter than this (stock 0.1 s 1-2 and 2-3, 0 for 3-4). Shift delay is the time from the shift command to the start of the ratio change; shift time is the time the ratio change itself takes. Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Effect: which shifts the adaptive learning uses Evidence: ledger:E0806, ledger:E1029, ledger:E1318</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C26A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x99D" flags="0x30">
    <title>Shift Adapt - Max Shift Time by Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A shift is not used for learning when its shift time is longer than this (stock 1.0 s 1-2 and 2-3, 0 for 3-4). Shift delay is the time from the shift command to the start of the ratio change; shift time is the time the ratio change itself takes. Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Effect: which shifts the adaptive learning uses Evidence: ledger:E0806, ledger:E1029, ledger:E1318</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C270" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x99E" flags="0x30">
    <title>Shift Adapt - Fixed Step Time Error Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the shift time error (desired minus measured) is below this, the Fixed Step for Much Slower Shifts is used instead of the shift time step (stock the lowest value: never). Shift delay is the time from the shift command to the start of the ratio change; shift time is the time the ratio change itself takes. Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1029, ledger:E1318</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C276" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>-204.800000</min>
      <max>204.793750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x99F" flags="0x30">
    <title>Shift Phase Pressure A, Torque Band 1, by Set and Shift vs Shift Pressure</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 words]; COUNT is a structure word - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra shift pressure A for torque band 1 (the PCM&#x27;s low / high engine torque band during shifts): three phase pressures are blended into the commanded shift pressure as the gear ratio moves through the start, full and end ratio points of the shift. Rows: pressure set (0 = normal modes, 2 = 4WD Low, 1 unused) and shift (1-2, 2-3, 3-4); columns: shift pressure 0 to 640 kPa. Negative values reduce pressure. All zero on stock. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on t...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>set / shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="set 0 1-2" />
      <LABEL index="1" value="set 0 2-3" />
      <LABEL index="2" value="set 0 3-4" />
      <LABEL index="3" value="set 1 1-2" />
      <LABEL index="4" value="set 1 2-3" />
      <LABEL index="5" value="set 1 3-4" />
      <LABEL index="6" value="set 2 1-2" />
      <LABEL index="7" value="set 2 2-3" />
      <LABEL index="8" value="set 2 3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A5E6" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9A0" flags="0x30">
    <title>Shift Phase Pressure B, Torque Band 1, by Set and Shift vs Shift Pressure</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 words]; COUNT is a structure word - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra shift pressure B for torque band 1 (the PCM&#x27;s low / high engine torque band during shifts): three phase pressures are blended into the commanded shift pressure as the gear ratio moves through the start, full and end ratio points of the shift. Rows: pressure set (0 = normal modes, 2 = 4WD Low, 1 unused) and shift (1-2, 2-3, 3-4); columns: shift pressure 0 to 640 kPa. Negative values reduce pressure. All zero on stock. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on t...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>set / shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="set 0 1-2" />
      <LABEL index="1" value="set 0 2-3" />
      <LABEL index="2" value="set 0 3-4" />
      <LABEL index="3" value="set 1 1-2" />
      <LABEL index="4" value="set 1 2-3" />
      <LABEL index="5" value="set 1 3-4" />
      <LABEL index="6" value="set 2 1-2" />
      <LABEL index="7" value="set 2 2-3" />
      <LABEL index="8" value="set 2 3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A72E" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9A1" flags="0x30">
    <title>Shift Phase Pressure C, Torque Band 1, by Set and Shift vs Shift Pressure</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 words]; COUNT is a structure word - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra shift pressure C for torque band 1 (the PCM&#x27;s low / high engine torque band during shifts): three phase pressures are blended into the commanded shift pressure as the gear ratio moves through the start, full and end ratio points of the shift. Rows: pressure set (0 = normal modes, 2 = 4WD Low, 1 unused) and shift (1-2, 2-3, 3-4); columns: shift pressure 0 to 640 kPa. Negative values reduce pressure. All zero on stock. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on t...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>set / shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="set 0 1-2" />
      <LABEL index="1" value="set 0 2-3" />
      <LABEL index="2" value="set 0 3-4" />
      <LABEL index="3" value="set 1 1-2" />
      <LABEL index="4" value="set 1 2-3" />
      <LABEL index="5" value="set 1 3-4" />
      <LABEL index="6" value="set 2 1-2" />
      <LABEL index="7" value="set 2 2-3" />
      <LABEL index="8" value="set 2 3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A876" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9A2" flags="0x30">
    <title>Shift Phase Pressure A, Torque Band 0, by Set and Shift vs Shift Pressure</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 words]; COUNT is a structure word - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra shift pressure A for torque band 0 (the PCM&#x27;s low / high engine torque band during shifts): three phase pressures are blended into the commanded shift pressure as the gear ratio moves through the start, full and end ratio points of the shift. Rows: pressure set (0 = normal modes, 2 = 4WD Low, 1 unused) and shift (1-2, 2-3, 3-4); columns: shift pressure 0 to 640 kPa. Negative values reduce pressure. All zero on stock. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on t...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>set / shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="set 0 1-2" />
      <LABEL index="1" value="set 0 2-3" />
      <LABEL index="2" value="set 0 3-4" />
      <LABEL index="3" value="set 1 1-2" />
      <LABEL index="4" value="set 1 2-3" />
      <LABEL index="5" value="set 1 3-4" />
      <LABEL index="6" value="set 2 1-2" />
      <LABEL index="7" value="set 2 2-3" />
      <LABEL index="8" value="set 2 3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3AB0E" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9A3" flags="0x30">
    <title>Shift Phase Pressure B, Torque Band 0, by Set and Shift vs Shift Pressure</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 words]; COUNT is a structure word - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra shift pressure B for torque band 0 (the PCM&#x27;s low / high engine torque band during shifts): three phase pressures are blended into the commanded shift pressure as the gear ratio moves through the start, full and end ratio points of the shift. Rows: pressure set (0 = normal modes, 2 = 4WD Low, 1 unused) and shift (1-2, 2-3, 3-4); columns: shift pressure 0 to 640 kPa. Negative values reduce pressure. All zero on stock. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on t...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>set / shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="set 0 1-2" />
      <LABEL index="1" value="set 0 2-3" />
      <LABEL index="2" value="set 0 3-4" />
      <LABEL index="3" value="set 1 1-2" />
      <LABEL index="4" value="set 1 2-3" />
      <LABEL index="5" value="set 1 3-4" />
      <LABEL index="6" value="set 2 1-2" />
      <LABEL index="7" value="set 2 2-3" />
      <LABEL index="8" value="set 2 3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3AC56" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9A4" flags="0x30">
    <title>Shift Phase Pressure C, Torque Band 0, by Set and Shift vs Shift Pressure</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 words]; COUNT is a structure word - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra shift pressure C for torque band 0 (the PCM&#x27;s low / high engine torque band during shifts): three phase pressures are blended into the commanded shift pressure as the gear ratio moves through the start, full and end ratio points of the shift. Rows: pressure set (0 = normal modes, 2 = 4WD Low, 1 unused) and shift (1-2, 2-3, 3-4); columns: shift pressure 0 to 640 kPa. Negative values reduce pressure. All zero on stock. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on t...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>set / shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="set 0 1-2" />
      <LABEL index="1" value="set 0 2-3" />
      <LABEL index="2" value="set 0 3-4" />
      <LABEL index="3" value="set 1 1-2" />
      <LABEL index="4" value="set 1 2-3" />
      <LABEL index="5" value="set 1 3-4" />
      <LABEL index="6" value="set 2 1-2" />
      <LABEL index="7" value="set 2 2-3" />
      <LABEL index="8" value="set 2 3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3AD9E" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9A5" flags="0x30">
    <title>Pedal Map - Vehicle Speed Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed of each row of all nine pedal to throttle area maps (the rate-limited pedal map speed input). Must keep rising. Stock 0, 3, 10, 20, 40, 60, 80, 100, 120 km/h. Effect: moves the vehicle speed each pedal map row applies to, in all nine maps Evidence: ledger:E1158, ledger:E1210, ledger:E1214</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>breakpoint index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24B9A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9A6" flags="0x30">
    <title>Post-Shift Pressure Offset, Initial, by Gear vs Base Shift Pressure (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 words]; COUNT is a structure word - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pressure added to the commanded shift pressure from the gear change until the delay time has passed. Negative values reduce pressure. Rows: gear (1st, 2nd, 3rd); columns: base shift pressure 0 to 640 kPa. Part of a pressure offset applied after a gear change in one of the controller&#x27;s shift pressure modes, and only when the feature&#x27;s enable switch is set. The switch is 0 on stock and every cell here is zero. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0362, ledger:E1165, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st gear" />
      <LABEL index="1" value="2nd gear" />
      <LABEL index="2" value="3rd gear" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3BE96" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9A7" flags="0x30">
    <title>Post-Shift Pressure Offset, Ramp Start, by Gear vs Base Shift Pressure (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 words]; COUNT is a structure word - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pressure offset at the start of the ramp, once the delay time has passed; it then moves in a straight line to the final offset over the ramp time. Negative values reduce pressure. Rows: gear (1st, 2nd, 3rd); columns: base shift pressure 0 to 640 kPa. Part of a pressure offset applied after a gear change in one of the controller&#x27;s shift pressure modes, and only when the feature&#x27;s enable switch is set. The switch is 0 on stock and every cell here is zero. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st gear" />
      <LABEL index="1" value="2nd gear" />
      <LABEL index="2" value="3rd gear" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3BF06" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9A8" flags="0x30">
    <title>Post-Shift Pressure Offset, Final, by Gear vs Base Shift Pressure (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 words]; COUNT is a structure word - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pressure offset held after the delay and ramp times have passed. Negative values reduce pressure. Rows: gear (1st, 2nd, 3rd); columns: base shift pressure 0 to 640 kPa. Part of a pressure offset applied after a gear change in one of the controller&#x27;s shift pressure modes, and only when the feature&#x27;s enable switch is set. The switch is 0 on stock and every cell here is zero. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0362, ledger:E1165, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st gear" />
      <LABEL index="1" value="2nd gear" />
      <LABEL index="2" value="3rd gear" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3BF76" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9A9" flags="0x30">
    <title>Post-Shift Pressure Offset, Delay Time, by Gear vs Base Shift Pressure (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 words]; COUNT is a structure word - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time after a gear change during which the initial offset is used. Rows: gear (1st, 2nd, 3rd); columns: base shift pressure 0 to 640 kPa. Part of a pressure offset applied after a gear change in one of the controller&#x27;s shift pressure modes, and only when the feature&#x27;s enable switch is set. The switch is 0 on stock and every cell here is zero. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0362, ledger:E1165, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st gear" />
      <LABEL index="1" value="2nd gear" />
      <LABEL index="2" value="3rd gear" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3BDB6" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9AA" flags="0x30">
    <title>Post-Shift Pressure Offset, Ramp Time, by Gear vs Base Shift Pressure (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 words]; COUNT is a structure word - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time taken to move from the ramp start offset to the final offset, counted from the end of the delay. Rows: gear (1st, 2nd, 3rd); columns: base shift pressure 0 to 640 kPa. Part of a pressure offset applied after a gear change in one of the controller&#x27;s shift pressure modes, and only when the feature&#x27;s enable switch is set. The switch is 0 on stock and every cell here is zero. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0362, ledger:E1165, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st gear" />
      <LABEL index="1" value="2nd gear" />
      <LABEL index="2" value="3rd gear" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3BE26" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9AB" flags="0x30">
    <title>Garage Shift First Phase Time Adder vs RPM vs Trans Temp - Into Drive (A)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time added to the first-phase time limit of a garage shift (into drive variant A), by engine speed (rows) and transmission fluid temperature (columns). A garage shift that follows a long enough time out of gear starts with a first phase; when the time since the start of the engagement reaches the limit, the controller moves on to the phase that uses the garage shift pressure tables by temperature and rpm. Stock all 0 (no extra time). A and B are the two engagement variants the controller chooses between, as for the garage shift pressure tables. Effect: raise = the first phase of this engagement may last longer before the pres...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x38196" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37FA3" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9AC" flags="0x30">
    <title>Garage Shift First Phase Time Adder vs RPM vs Trans Temp - Into Drive (B)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time added to the first-phase time limit of a garage shift (into drive variant B), by engine speed (rows) and transmission fluid temperature (columns). A garage shift that follows a long enough time out of gear starts with a first phase; when the time since the start of the engagement reaches the limit, the controller moves on to the phase that uses the garage shift pressure tables by temperature and rpm. Stock all 0 (no extra time). A and B are the two engagement variants the controller chooses between, as for the garage shift pressure tables. Effect: raise = the first phase of this engagement may last longer before the pres...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x38196" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37E83" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9AD" flags="0x30">
    <title>Garage Shift First Phase Time Adder vs RPM vs Trans Temp - Into Reverse (A)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time added to the first-phase time limit of a garage shift (into reverse variant A), by engine speed (rows) and transmission fluid temperature (columns). A garage shift that follows a long enough time out of gear starts with a first phase; when the time since the start of the engagement reaches the limit, the controller moves on to the phase that uses the garage shift pressure tables by temperature and rpm. Stock all 0 (no extra time). A and B are the two engagement variants the controller chooses between, as for the garage shift pressure tables. Effect: raise = the first phase of this engagement may last longer before the pr...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x38196" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x380AB" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9AE" flags="0x30">
    <title>Garage Shift First Phase Time Adder vs RPM vs Trans Temp - Into Reverse (B)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time added to the first-phase time limit of a garage shift (into reverse variant B), by engine speed (rows) and transmission fluid temperature (columns). A garage shift that follows a long enough time out of gear starts with a first phase; when the time since the start of the engagement reaches the limit, the controller moves on to the phase that uses the garage shift pressure tables by temperature and rpm. Stock all 0 (no extra time). A and B are the two engagement variants the controller chooses between, as for the garage shift pressure tables. Effect: raise = the first phase of this engagement may last longer before the pr...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x38196" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37E2B" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9AF" flags="0x30">
    <title>Downshift Pressure Temp Modifier - Gear 1</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pressure added to the base shift pressure during a downshift, by base shift pressure (rows) and transmission fluid temperature (columns); the downshift counterpart of the Upshift Pressure Temp Modifier tables. The controller picks the table by its gear index during the downshift; this one is used while that index is 1st gear, in the usual two shift pressure modes. Stock all 0 (no change). Effect: positive = firmer downshift at that temperature and base pressure, negative = softer Evidence: ledger:E0237, ledger:E1170</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (trans temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>kPa (base shift pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="160" />
      <LABEL index="2" value="320" />
      <LABEL index="3" value="480" />
      <LABEL index="4" value="640" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3B0FA" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9B0" flags="0x30">
    <title>Downshift Pressure Temp Modifier (alternate pressure mode) - Gear 1</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pressure added to the base shift pressure during a downshift, by base shift pressure (rows) and transmission fluid temperature (columns); the downshift counterpart of the Upshift Pressure Temp Modifier tables. The controller picks the table by its gear index during the downshift; this one is used while that index is 1st gear, in a third shift pressure mode. Stock all 0 (no change). Effect: positive = firmer downshift at that temperature and base pressure, negative = softer Evidence: ledger:E0237, ledger:E1170</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (trans temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>kPa (base shift pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="160" />
      <LABEL index="2" value="320" />
      <LABEL index="3" value="480" />
      <LABEL index="4" value="640" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3B30A" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9B1" flags="0x30">
    <title>Transmission Input Torque Limit vs Input Speed - 1st Gear, base</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Limit on transmission input (turbine) torque by transmission input speed, for 1st gear outside 4WD-Low and 4WD-High. When the limit is armed and the input torque is above it, the transmission asks the engine for proportionally less torque. Arming needs engine speed and throttle above two thresholds that the stock calibration sets out of reach (8000 rpm), so the limit never acts. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0359, ledger:E1172, ledger:E1175, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3ED06" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (input speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EC16" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9B2" flags="0x30">
    <title>Transmission Input Torque Limit vs Input Speed - 2nd Gear, base</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Limit on transmission input (turbine) torque by transmission input speed, for 2nd gear outside 4WD-Low and 4WD-High. When the limit is armed and the input torque is above it, the transmission asks the engine for proportionally less torque. Arming needs engine speed and throttle above two thresholds that the stock calibration sets out of reach (8000 rpm), so the limit never acts. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0359, ledger:E1172, ledger:E1175, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3ED1A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (input speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EC2A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9B3" flags="0x30">
    <title>Transmission Input Torque Limit vs Input Speed - 3rd Gear, base</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Limit on transmission input (turbine) torque by transmission input speed, for 3rd gear outside 4WD-Low and 4WD-High. When the limit is armed and the input torque is above it, the transmission asks the engine for proportionally less torque. Arming needs engine speed and throttle above two thresholds that the stock calibration sets out of reach (8000 rpm), so the limit never acts. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0359, ledger:E1172, ledger:E1175, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3ED2E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (input speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EC3E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9B4" flags="0x30">
    <title>Transmission Input Torque Limit vs Input Speed - 4th Gear, base</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Limit on transmission input (turbine) torque by transmission input speed, for 4th gear outside 4WD-Low and 4WD-High. When the limit is armed and the input torque is above it, the transmission asks the engine for proportionally less torque. Arming needs engine speed and throttle above two thresholds that the stock calibration sets out of reach (8000 rpm), so the limit never acts. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0359, ledger:E1172, ledger:E1175, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3ED42" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (input speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EC52" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9B5" flags="0x30">
    <title>Transmission Input Torque Limit vs Input Speed - 1st Gear, 4WD-Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Limit on transmission input (turbine) torque by transmission input speed, for 1st gear in 4WD-Low (transfer case range). When the limit is armed and the input torque is above it, the transmission asks the engine for proportionally less torque. Arming needs engine speed and throttle above two thresholds that the stock calibration sets out of reach (8000 rpm), so the limit never acts. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0359, ledger:E1172, ledger:E1175, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3ED06" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (input speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EC66" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9B6" flags="0x30">
    <title>Transmission Input Torque Limit vs Input Speed - 2nd Gear, 4WD-Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Limit on transmission input (turbine) torque by transmission input speed, for 2nd gear in 4WD-Low (transfer case range). When the limit is armed and the input torque is above it, the transmission asks the engine for proportionally less torque. Arming needs engine speed and throttle above two thresholds that the stock calibration sets out of reach (8000 rpm), so the limit never acts. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0359, ledger:E1172, ledger:E1175, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3ED1A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (input speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EC7A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9B7" flags="0x30">
    <title>Transmission Input Torque Limit vs Input Speed - 3rd Gear, 4WD-Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Limit on transmission input (turbine) torque by transmission input speed, for 3rd gear in 4WD-Low (transfer case range). When the limit is armed and the input torque is above it, the transmission asks the engine for proportionally less torque. Arming needs engine speed and throttle above two thresholds that the stock calibration sets out of reach (8000 rpm), so the limit never acts. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0359, ledger:E1172, ledger:E1175, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3ED2E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (input speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EC8E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9B8" flags="0x30">
    <title>Transmission Input Torque Limit vs Input Speed - 4th Gear, 4WD-Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Limit on transmission input (turbine) torque by transmission input speed, for 4th gear in 4WD-Low (transfer case range). When the limit is armed and the input torque is above it, the transmission asks the engine for proportionally less torque. Arming needs engine speed and throttle above two thresholds that the stock calibration sets out of reach (8000 rpm), so the limit never acts. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0359, ledger:E1172, ledger:E1175, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3ED42" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (input speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3ECA2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9B9" flags="0x30">
    <title>Transmission Input Torque Limit vs Input Speed - 1st Gear, 4WD-High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Limit on transmission input (turbine) torque by transmission input speed, for 1st gear in 4WD-High (transfer case range). When the limit is armed and the input torque is above it, the transmission asks the engine for proportionally less torque. Arming needs engine speed and throttle above two thresholds that the stock calibration sets out of reach (8000 rpm), so the limit never acts. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0359, ledger:E1172, ledger:E1175, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3ED06" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (input speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3ECB6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9BA" flags="0x30">
    <title>Transmission Input Torque Limit vs Input Speed - 2nd Gear, 4WD-High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Limit on transmission input (turbine) torque by transmission input speed, for 2nd gear in 4WD-High (transfer case range). When the limit is armed and the input torque is above it, the transmission asks the engine for proportionally less torque. Arming needs engine speed and throttle above two thresholds that the stock calibration sets out of reach (8000 rpm), so the limit never acts. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0359, ledger:E1172, ledger:E1175, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3ED1A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (input speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3ECCA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9BB" flags="0x30">
    <title>Transmission Input Torque Limit vs Input Speed - 3rd Gear, 4WD-High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Limit on transmission input (turbine) torque by transmission input speed, for 3rd gear in 4WD-High (transfer case range). When the limit is armed and the input torque is above it, the transmission asks the engine for proportionally less torque. Arming needs engine speed and throttle above two thresholds that the stock calibration sets out of reach (8000 rpm), so the limit never acts. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0359, ledger:E1172, ledger:E1175, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3ED2E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (input speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3ECDE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9BC" flags="0x30">
    <title>Transmission Input Torque Limit vs Input Speed - 4th Gear, 4WD-High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Limit on transmission input (turbine) torque by transmission input speed, for 4th gear in 4WD-High (transfer case range). When the limit is armed and the input torque is above it, the transmission asks the engine for proportionally less torque. Arming needs engine speed and throttle above two thresholds that the stock calibration sets out of reach (8000 rpm), so the limit never acts. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0359, ledger:E1172, ledger:E1175, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3ED42" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (input speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3ECF2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9BD" flags="0x30">
    <title>Upshift Inhibit - Expected Throttle vs Speed (mode 8, dormant)</title>
    <description>Change in small steps and log. Each row is a 1-D curve [COUNT = 17][17 points]; COUNT is a structure word, never edit it (E0345). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The throttle the upshift inhibit predictor assumes the driver will hold after an upshift, by vehicle speed and current gear, for shift mode 8. Same layout and unit as the two sets used in the other shift modes. The upshift inhibit is not enabled for shift mode 8 on this calibration, so this set is never read; stock all 100 %. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0345, ledger:E1176</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0.0" />
      <LABEL index="2" value="6.2" />
      <LABEL index="3" value="12.4" />
      <LABEL index="4" value="18.6" />
      <LABEL index="5" value="24.9" />
      <LABEL index="6" value="31.1" />
      <LABEL index="7" value="37.3" />
      <LABEL index="8" value="43.5" />
      <LABEL index="9" value="49.7" />
      <LABEL index="10" value="55.9" />
      <LABEL index="11" value="62.1" />
      <LABEL index="12" value="68.4" />
      <LABEL index="13" value="74.6" />
      <LABEL index="14" value="80.8" />
      <LABEL index="15" value="87.0" />
      <LABEL index="16" value="93.2" />
      <LABEL index="17" value="99.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>current gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39258" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle demand</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9BE" flags="0x30">
    <title>Minimum Line Pressure - Input Torque Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Input torque points of the rows of the minimum line pressure tables. Stock 0 to 8192 Nm in even steps, far beyond real torque, so only the first row and part of the second are ever reached; set realistic points before using those tables. Effect: moves the axis of every table that uses it: keep the point count and keep the points rising Evidence: ledger:E1177</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x383DE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9BF" flags="0x30">
    <title>Minimum Line Pressure - Output Speed Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission output speed points of the columns of the minimum line pressure tables. Stock 0 to 8192 rpm in 512 rpm steps. Effect: moves the axis of every table that uses it: keep the point count and keep the points rising Evidence: ledger:E1177</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x383EA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9C0" flags="0x30">
    <title>Upshift Inhibit - Vehicle Speed Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed points of the upshift inhibit expected throttle tables. Stock 0 to 160 km/h in 10 km/h steps. Effect: moves the axis of every table that uses it: keep the point count and keep the points rising Evidence: ledger:E1177</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3937A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9C1" flags="0x30">
    <title>Garage Shift - Fluid Temperature Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission fluid temperature points of the garage shift pressure and first-phase time tables. Stock -28 to 140 C in 21 C steps. Effect: moves the axis of every table that uses it: keep the point count and keep the points rising Evidence: ledger:E1177</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38196" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9C2" flags="0x30">
    <title>Transmission Input Torque Limit - Input Speed Breakpoints, 1st Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission input speed points of the 1st gear input torque limit curves. Stock 0 to 6400 rpm in 800 rpm steps. The limit they belong to never arms on this calibration. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E1177</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3ED06" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x9C3" flags="0x0">
    <title>Transmission Input Torque Limit in Reverse, 4WD-High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Limit on transmission input (turbine) torque in Reverse, used in 4WD-High (transfer case range) in place of the per-gear limit curves. Stock 827 Nm. The limit never arms on this calibration (its arming thresholds are out of reach). Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0773, ledger:E1175, ledger:E1178, ledger:E1215</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3EC12" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x9C4" flags="0x30">
    <title>Accelerator Pedal Filter - Gap Points, Rising</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal gap points (pedal demand minus filtered pedal, %) at which the rising filter gain table is defined. Stock 0 to 0.094 %, the scale set by the stock rate scale word. Effect: moves the axis of the rising filter gain table: keep 17 points and keep them rising Evidence: ledger:E0330, ledger:E1190, ledger:E1329</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24D9C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (pedal gap)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>95.998066</max>
      <MATH equation="X/682.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9C5" flags="0x30">
    <title>Accelerator Pedal Filter - Gap Points, Falling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal gap points (pedal demand minus filtered pedal, %) at which the falling filter gain table is defined. Stock 0 to 0.094 %, the scale set by the stock rate scale word. Effect: moves the axis of the falling filter gain table: keep 17 points and keep them rising Evidence: ledger:E0330, ledger:E1190, ledger:E1329</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24DE6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (pedal gap)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>95.998066</max>
      <MATH equation="X/682.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x9C6" flags="0x0">
    <title>Driveline Torque Calc - Final Drive Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Final drive (axle) ratio in the driveline torque estimate: engine torque x converter torque ratio x gear ratio x this ratio x range multiplier. Stock 4.56. Used only in this estimate, which feeds the pedal filter axle torque factor and the pedal gain reduction; it does not change road speed or shift calculations. Range 0 to 8.0. Effect: changes the driveline torque estimate used by the pedal filter and pedal gain reduction Evidence: ledger:E0444, ledger:E1203, ledger:E1204</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2006E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>:1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9C7" flags="0x0">
    <title>Driveline Torque Calc - Reverse Gear Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Gear ratio used in place of the gear ratio table when in Reverse, in the driveline torque estimate. Stock 3.672. Used only in this estimate, which feeds the pedal filter axle torque factor and the pedal gain reduction. Range 0 to 8.0. Effect: changes the driveline torque estimate in Reverse Evidence: ledger:E0444, ledger:E1203, ledger:E1204</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x20070" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>:1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9C8" flags="0x0">
    <title>Pedal Gain Reduction - Request Factor Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest value the pedal gain reduction may cut the pedal throttle request factor to. Stock 1.0, so no cut is applied whatever the Request Factor Cut table holds. Effect: lower = the pedal gain reduction may cut the pedal request further Evidence: ledger:E0436, ledger:E1206</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23FB8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9C9" flags="0x0">
    <title>Pedal Gain Reduction - Step-Up Re-Arm Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The pedal gain reduction step-up is armed again once vehicle speed drops below this speed. Stock 5 km/h. Effect: raise = the step-up re-arms without the truck having to slow as far Evidence: ledger:E0436, ledger:E1208</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23FBA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9CA" flags="0x0">
    <title>Pedal Gain Reduction - Step-Up Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When armed and no reduction is active, the step-up is taken once as vehicle speed rises above this speed. Stock 40 km/h. Effect: lower = the step-up is taken at a lower speed Evidence: ledger:E0436, ledger:E1208</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23FBC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9CB" flags="0x0">
    <title>Pedal Gain Reduction - Request Factor Step-Up</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Amount added back to the pedal throttle request factor once per re-arm, after a pedal gain reduction, when speed rises past the Step-Up Speed. It takes effect when the pedal is released (1 percent or less) or at more than 90 percent pedal with manifold vacuum below the vacuum threshold vs rpm (stock 10 kPa); until then it waits. The factor never goes above 1.0. Stock 0, so nothing is added back. Effect: raise = more of a pedal gain reduction is given back each time the truck speeds up again Evidence: ledger:E0436, ledger:E1208</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23FBE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x9CC" flags="0x30">
    <title>Pedal Map Select vs Trans State - Normal</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Which pedal to throttle map is used in each transmission state in normal driving: 0 = Gears 1-3 + Park/Neutral map, 1 = 4th Gear map, 2 = Reverse map. Stock 1 in 4th and 2 in Reverse, 0 elsewhere. The choice changes only while the pedal is at rest or wide open. Allowed values are 0, 1 and 2 only; any other value makes the pedal read the wrong map or no map. Effect: changes which pedal map is used in that transmission state Evidence: ledger:E0240, ledger:E1210</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>transmission state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="Neutral" />
      <LABEL index="7" value="Reverse" />
      <LABEL index="8" value="Park" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24B14" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>map slot</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x9CD" flags="0x0">
    <title>Pedal Request Factor - Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest value the combined pedal request factor (the product of all pedal request factors, including the pedal gain increase) may reach. Stock 1.0, so the pedal gain increase cannot raise the pedal request above the map value. Range 0 to 2.0. Effect: raise = lets the pedal gain increase raise the pedal request above the map value Evidence: ledger:E0436, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23FC0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9CE" flags="0x0">
    <title>Pedal Gain Increase - Maximum Speed Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The pedal gain increase learn runs only in a launch: below the Maximum Speed, input / output speed ratio at or below the Maximum Speed Ratio and acceleration above the Minimum Acceleration. On stock it never runs (ratio 0 and 120 km/h/s). This is the highest transmission input / output speed ratio at which it runs. Stock 0. Effect: raise = the learn may run (it needs a ratio at or below this) Evidence: ledger:E0436, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23FC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>:1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9CF" flags="0x0">
    <title>Pedal Gain Increase - Maximum Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The pedal gain increase learn runs only in a launch: below the Maximum Speed, input / output speed ratio at or below the Maximum Speed Ratio and acceleration above the Minimum Acceleration. On stock it never runs (ratio 0 and 120 km/h/s). This is the speed below which it runs. Stock 20 km/h. Effect: raise = the learn runs up to a higher speed Evidence: ledger:E0436, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23FC6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9D0" flags="0x0">
    <title>Pedal Gain Increase - Minimum Acceleration</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The pedal gain increase learn runs only in a launch: below the Maximum Speed, input / output speed ratio at or below the Maximum Speed Ratio and acceleration above the Minimum Acceleration. On stock it never runs (ratio 0 and 120 km/h/s). This is the acceleration above which it runs. Stock 120 km/h/s (never reached). Effect: lower = the learn runs at milder acceleration Evidence: ledger:E0436, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23FC8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9D1" flags="0x0">
    <title>Pedal Gain Increase - Samples per Update</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of passes the pedal gain increase learn averages before it updates the increase (each pass adds the pedal gain reduction acceleration threshold divided by the measured acceleration). Stock 40. Effect: raise = the increase updates less often, from a longer average Evidence: ledger:E0436, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23FCA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9D2" flags="0x0">
    <title>Pedal Gain Increase - Rise Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the way the pedal gain increase moves toward a higher new value at each update. Stock 1.0 (all the way). Range 0 to 1.0. Effect: lower = the increase builds up over more updates Evidence: ledger:E0436, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23FE0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9D3" flags="0x0">
    <title>Pedal Gain Increase - Fall Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the way the pedal gain increase moves toward a lower new value at each update. Stock 1.0 (all the way). Range 0 to 1.0. Effect: lower = the increase falls away over more updates Evidence: ledger:E0436, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23FE2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x9D4" flags="0x30">
    <title>Pedal Map - Pedal Position Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal position of each column of all nine pedal to throttle area maps. Must keep rising from left to right. Stock 0, 3.1, 6.3, 12.5 then 6.25 % steps to 87.5, last column 97.0 %. At or below the first breakpoint the throttle area demand is 0 whatever the maps hold. Effect: moves the pedal position each pedal map column applies to, in all nine maps Evidence: ledger:E0232, ledger:E1214</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>breakpoint index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24B76" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x9D5" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - Trans State 5</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in transmission state 5 (not used on the 4-speed). 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25972" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9D6" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - Trans State 4, Converter Clutch Applied</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in transmission state 4 (not used on the 4-speed) with the converter clutch applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25974" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9D7" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - Trans State 4, Converter Clutch Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in transmission state 4 (not used on the 4-speed) with the converter clutch not applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25976" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9D8" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 4th Gear, Converter Clutch Applied</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 4th gear with the converter clutch applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25978" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9D9" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 4th Gear, Converter Clutch Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 4th gear with the converter clutch not applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2597A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9DA" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 3rd Gear, Converter Clutch Applied</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 3rd gear with the converter clutch applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2597C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9DB" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 3rd Gear, Converter Clutch Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 3rd gear with the converter clutch not applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2597E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9DC" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 2nd, Neutral, Reverse, Park, Warm, Converter Clutch Applied</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 2nd gear, Neutral, Reverse or Park, coolant at or above the cold threshold, converter clutch applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25980" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9DD" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 2nd, Neutral, Reverse, Park, Warm, Converter Clutch Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 2nd gear, Neutral, Reverse or Park, coolant at or above the cold threshold, converter clutch not applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25982" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9DE" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 2nd, Neutral, Reverse, Park, Cold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 2nd gear, Neutral, Reverse or Park with the coolant below the cold threshold. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25984" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9DF" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 1st Gear, Warm</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 1st gear with the coolant at or above the cold threshold. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25986" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9E0" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 1st Gear, Cold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 1st gear with the coolant below the cold threshold. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25988" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9E1" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 4WD-Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 4WD-Low, any gear. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2598A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x9E2" flags="0x30">
    <title>A/C Idle Air - RPM Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the A/C idle air target by engine speed (0 to 6400 rpm). Shown with 1.0 = stock, because the A/C idle air target&#x27;s scaling already includes the stock factor; 2.0 doubles the A/C idle air at that speed. Stock 1.0 everywhere. Effect: raise = more idle air for the A/C compressor at that engine speed Evidence: ledger:E1230</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="400" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1200" />
      <LABEL index="4" value="1600" />
      <LABEL index="5" value="2000" />
      <LABEL index="6" value="2400" />
      <LABEL index="7" value="2800" />
      <LABEL index="8" value="3200" />
      <LABEL index="9" value="3600" />
      <LABEL index="10" value="4000" />
      <LABEL index="11" value="4400" />
      <LABEL index="12" value="4800" />
      <LABEL index="13" value="5200" />
      <LABEL index="14" value="5600" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x290E8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9E3" flags="0x30">
    <title>Garage Shift First Phase - Minimum Time Out of Gear, Into Drive</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Garage shift (shift from Park or Neutral into gear): the first (timed) phase is used only when the transmission was out of gear longer than this, by fluid temperature. Stock 2.0 s. Effect: raise = the first phase is skipped after shorter stops in Park or Neutral Evidence: ledger:E1169, ledger:E1231</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-28" />
      <LABEL index="1" value="-7" />
      <LABEL index="2" value="14" />
      <LABEL index="3" value="35" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="77" />
      <LABEL index="6" value="98" />
      <LABEL index="7" value="119" />
      <LABEL index="8" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38100" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9E4" flags="0x30">
    <title>Garage Shift First Phase - Minimum Time Out of Gear, Into Reverse</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Garage shift (shift from Park or Neutral into gear): the first (timed) phase is used only when the transmission was out of gear longer than this, by fluid temperature. Stock 2.0 s. Effect: raise = the first phase is skipped after shorter stops in Park or Neutral Evidence: ledger:E1169, ledger:E1231</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-28" />
      <LABEL index="1" value="-7" />
      <LABEL index="2" value="14" />
      <LABEL index="3" value="35" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="77" />
      <LABEL index="6" value="98" />
      <LABEL index="7" value="119" />
      <LABEL index="8" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3810B" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9E5" flags="0x30">
    <title>Garage Shift First Phase - Base Time Limit, Into Drive</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Garage shift (shift from Park or Neutral into gear): base part of the first-phase time limit, by time out of gear; the first-phase time adder tables add to it. Used for the Drive (A) engagement. Stock 3.175 s. Effect: raise = longer first phase Evidence: ledger:E1169, ledger:E1231</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>s</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3811A" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9E6" flags="0x30">
    <title>Garage Shift First Phase - Base Time Limit, Into Reverse</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Garage shift (shift from Park or Neutral into gear): base part of the first-phase time limit, by time out of gear; the first-phase time adder tables add to it. Used for the Reverse (A) engagement. Stock 3.175 s. Effect: raise = longer first phase Evidence: ledger:E1169, ledger:E1231</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>s</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38125" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9E7" flags="0x30">
    <title>Garage Shift First Phase - Time Out of Gear Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Garage shift (shift from Park or Neutral into gear): time-out-of-gear breakpoints of the two base time curves. Stock all 0, so the last point of each curve applies. Effect: moves the time points of the base time curves Evidence: ledger:E1169, ledger:E1231</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38130" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9E8" flags="0x30">
    <title>Garage Shift Cold Soak - First Phase Time Adder, Into Drive</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold-soak garage shift: used for the first garage shift after a start (within 30 s) when coolant, transmission fluid and intake air temperatures agree. Time added to the first-phase time limit, by fluid temperature. Stock 0. Dormant: the cold-soak check is switched off in this calibration, so it has no effect on this truck&#x27;s software. Effect: raise = longer first phase after a cold soak Evidence: ledger:E1169, ledger:E1235</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38144" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9E9" flags="0x30">
    <title>Garage Shift Cold Soak - First Phase Time Adder, Into Reverse</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold-soak garage shift: used for the first garage shift after a start (within 30 s) when coolant, transmission fluid and intake air temperatures agree. Time added to the first-phase time limit, by fluid temperature. Stock 0. Dormant: the cold-soak check is switched off in this calibration, so it has no effect on this truck&#x27;s software. Effect: raise = longer first phase after a cold soak Evidence: ledger:E1169, ledger:E1235</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38158" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9EA" flags="0x30">
    <title>Garage Shift Cold Soak - Pressure Adder, Into Drive</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold-soak garage shift: used for the first garage shift after a start (within 30 s) when coolant, transmission fluid and intake air temperatures agree. Pressure added to the garage shift pressure, by fluid temperature. Stock 0. Dormant: the cold-soak check is switched off in this calibration, so it has no effect on this truck&#x27;s software. Effect: raise = firmer garage shift after a cold soak Evidence: ledger:E1169, ledger:E1235</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3816C" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>1020.000000</max>
      <MATH equation="X*4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9EB" flags="0x30">
    <title>Garage Shift Cold Soak - Pressure Adder, Into Reverse</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold-soak garage shift: used for the first garage shift after a start (within 30 s) when coolant, transmission fluid and intake air temperatures agree. Pressure added to the garage shift pressure, by fluid temperature. Stock 0. Dormant: the cold-soak check is switched off in this calibration, so it has no effect on this truck&#x27;s software. Effect: raise = firmer garage shift after a cold soak Evidence: ledger:E1169, ledger:E1235</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38177" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>1020.000000</max>
      <MATH equation="X*4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9EC" flags="0x30">
    <title>Garage Shift Cold Soak - Fluid Temperature Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold-soak garage shift: used for the first garage shift after a start (within 30 s) when coolant, transmission fluid and intake air temperatures agree. Fluid temperature breakpoints of the four cold-soak adder curves. Stock all 0, so the last point applies. Dormant: the cold-soak check is switched off in this calibration, so it has no effect on this truck&#x27;s software. Effect: moves the temperature points of the cold-soak adders Evidence: ledger:E1169, ledger:E1235</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38182" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x9ED" flags="0x0">
    <title>Garage Shift Cold Soak - Coolant Above Fluid Temperature Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold-soak garage shift: used for the first garage shift after a start (within 30 s) when coolant, transmission fluid and intake air temperatures agree. The soak counts only while coolant is less than this much above transmission fluid temperature. Stock 0. Dormant: the cold-soak check is switched off in this calibration, so it has no effect on this truck&#x27;s software. Effect: raise = the soak check accepts a bigger coolant / fluid difference Evidence: ledger:E1169, ledger:E1235</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF60" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9EE" flags="0x0">
    <title>Garage Shift Cold Soak - Coolant Above Intake Air Temperature Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold-soak garage shift: used for the first garage shift after a start (within 30 s) when coolant, transmission fluid and intake air temperatures agree. The soak counts only while coolant is less than this much above intake air temperature. Stock 0. Dormant: the cold-soak check is switched off in this calibration, so it has no effect on this truck&#x27;s software. Effect: raise = the soak check accepts a bigger coolant / intake air difference Evidence: ledger:E1169, ledger:E1235</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF62" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9EF" flags="0x0">
    <title>Garage Shift Cold Soak - Check Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Switch for the garage shift cold-soak check: 0 (stock) = off. Effect: non-zero = the cold-soak adders can apply Evidence: ledger:E1169, ledger:E1235, ledger:E1577</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF5E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>switch</units>
    <decimalpl>0</decimalpl>
    <min>-32768.000000</min>
    <max>32767.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x9F0" flags="0x30">
    <title>Converter Model - Converter Torque Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque breakpoints of the square-root lookup (stock 0 to 438 Nm, each step about 1.5 times the last). Part of the torque converter model check: the PCM computes a converter capacity factor (engine speed over the square root of the torque going through the converter fluid, in rpm per square root of Nm), predicts the converter speed ratio from it and flags a mismatch when the measured speed ratio falls outside the band. Effect: moves the torque points of the square-root lookup Evidence: ledger:E0348, ledger:E1238</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EA64" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9F1" flags="0x30">
    <title>Converter Model - Capacity Factor Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Capacity factor breakpoints of the expected speed ratio curve (stock 164 to 217, then 439 as the end point; points 2 to 4 are not rising on stock). Part of the torque converter model check: the PCM computes a converter capacity factor (engine speed over the square root of the torque going through the converter fluid, in rpm per square root of Nm), predicts the converter speed ratio from it and flags a mismatch when the measured speed ratio falls outside the band. Effect: moves the capacity factor points of the expected speed ratio curve Evidence: ledger:E0348, ledger:E1238</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EA40" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm/sqrt(Nm)</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x9F2" flags="0x0">
    <title>P0506 / P0507 Pass - Idle Speed Error Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The tests pass once the filtered idle speed error (either direction) stays at or below this for the pass time. Stock 50 rpm. Part of the idle speed diagnostic (P0506 idle speed lower than expected, P0507 higher than expected), which runs only once its enable conditions are met. Effect: raise = the tests pass with a larger idle speed error Evidence: ledger:E0639, ledger:E1239</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36554" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9F3" flags="0x0">
    <title>P0506 / P0507 Pass - Idle Speed Error Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain for the idle speed error used by the pass check (fraction of the new error taken each update). Stock 0.2. Part of the idle speed diagnostic (P0506 idle speed lower than expected, P0507 higher than expected), which runs only once its enable conditions are met. Effect: raise = the filtered error follows the idle speed error faster Evidence: ledger:E0639, ledger:E1239</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36556" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9F4" flags="0x0">
    <title>P0506 / P0507 Pass - Time Within Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the filtered idle speed error must stay within the pass maximum before both tests report a pass and the fail period counts are cleared. Stock 3 s. Part of the idle speed diagnostic (P0506 idle speed lower than expected, P0507 higher than expected), which runs only once its enable conditions are met. Effect: raise = longer stable idle needed for a pass Evidence: ledger:E0639, ledger:E1239</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36558" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9F5" flags="0x0">
    <title>Vehicle Bus - A/C Refrigerant Pressure Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the change threshold for the A/C refrigerant pressure message. Stock 28 kPa. Effect: raise = fewer, coarser updates Evidence: ledger:E1243</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20274" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9F6" flags="0x0">
    <title>Vehicle Bus - A/C Refrigerant Pressure Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the minimum interval for the A/C refrigerant pressure message. Stock 0.3 s. Effect: raise = less frequent updates Evidence: ledger:E1243</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20276" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9F7" flags="0x0">
    <title>Vehicle Bus - Coolant Temperature Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent. This is the change threshold for the coolant temperature message (no minimum interval). Stock 1 C. Effect: raise = fewer, coarser updates Evidence: ledger:E1243</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2027C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9F8" flags="0x0">
    <title>Vehicle Bus - Engine Torque Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the change threshold for the engine torque message. Stock 10 Nm. Effect: raise = fewer, coarser updates Evidence: ledger:E1243</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2027E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>16383.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9F9" flags="0x0">
    <title>Vehicle Bus - Engine Torque Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the minimum interval for the engine torque message. Stock 0.1 s. Effect: raise = less frequent updates Evidence: ledger:E1243</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20280" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9FA" flags="0x0">
    <title>Vehicle Bus - Engine Speed Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the change threshold for the engine speed message. Stock 16 rpm. Effect: raise = fewer, coarser updates Evidence: ledger:E1243</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20286" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9FB" flags="0x0">
    <title>Vehicle Bus - Engine Speed Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the minimum interval for the engine speed message. Stock 0.1 s. Effect: raise = less frequent updates Evidence: ledger:E1243</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20288" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9FC" flags="0x0">
    <title>Vehicle Bus - Oil Pressure Message Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A new oil pressure message (Class 2 message 4B11) goes out once the smoothed oil pressure has changed by this much since the last one sent and the minimum interval has passed. Stock 8 kPa. Effect: raise = fewer, coarser updates Evidence: ledger:E1243, ledger:E1246, ledger:E1831</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x20282" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9FD" flags="0x0">
    <title>Vehicle Bus - Class 2 Message 4B11 Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this percentage to another module on the vehicle bus (Class 2 message 4B11 / 4A11, byte 1, full scale 100 %); which module receives it, and what that module does with it, has not been determined, so the receiver is not established. The PCM itself does not use the value. A new message goes out once the value has changed by the change threshold since the last one sent and at least this long has passed. Stock 0.5 s. Effect: raise = less frequent updates Evidence: ledger:E1243, ledger:E1246</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20284" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9FE" flags="0x0">
    <title>Vehicle Bus - Vehicle Speed Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the change threshold for the vehicle speed message. Stock 0.2 km/h. Effect: raise = fewer, coarser updates Evidence: ledger:E1244</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x202B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x9FF" flags="0x0">
    <title>Vehicle Bus - Vehicle Speed Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the minimum interval for the vehicle speed message. Stock 0.1 s. Effect: raise = less frequent updates Evidence: ledger:E1244</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x202B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA00" flags="0x0">
    <title>High Engine Speed State 1 - Step-Up Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. High engine speed state: it steps up from normal to the first high state, and from there to the second, as engine speed rises past the step-up speeds, and back down at the step-down speeds. In either high state the airmass is taken from the mass airflow sensor only; fuel and spark routines also read the state. The state goes from normal to the first high state above this speed. Stock 5000 rpm. Effect: raise = MAF-only airmass starts at a higher speed Evidence: ledger:E0219, ledger:E0868, ledger:E1245</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x23A7C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA01" flags="0x0">
    <title>High Engine Speed State 1 - Step-Down Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. High engine speed state: it steps up from normal to the first high state, and from there to the second, as engine speed rises past the step-up speeds, and back down at the step-down speeds. In either high state the airmass is taken from the mass airflow sensor only; fuel and spark routines also read the state. The state goes from the first high state back to normal at or below this speed. Stock 4900 rpm. Effect: lower = the high state holds to a lower speed Evidence: ledger:E0219, ledger:E0868, ledger:E1245</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x23A7E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA02" flags="0x0">
    <title>High Engine Speed State 2 - Step-Up Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. High engine speed state: it steps up from normal to the first high state, and from there to the second, as engine speed rises past the step-up speeds, and back down at the step-down speeds. In either high state the airmass is taken from the mass airflow sensor only; fuel and spark routines also read the state. The state goes from the first to the second high state above this speed. Stock 5800 rpm. Effect: raise = the second high state starts at a higher speed Evidence: ledger:E0219, ledger:E0868, ledger:E1245</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x23A80" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA03" flags="0x0">
    <title>High Engine Speed State 2 - Step-Down Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. High engine speed state: it steps up from normal to the first high state, and from there to the second, as engine speed rises past the step-up speeds, and back down at the step-down speeds. In either high state the airmass is taken from the mass airflow sensor only; fuel and spark routines also read the state. The state goes from the second high state back to the first at or below this speed. Stock 5700 rpm. Effect: lower = the second high state holds to a lower speed Evidence: ledger:E0219, ledger:E0868, ledger:E1245</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x23A82" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xA04" flags="0x30">
    <title>Closed Loop O2 Filter Gain - Error Signal, Bank 2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): filter on the O2 voltage that is used to work out how far the signal is past the switch point (the input of the step interval and proportional factors), by airflow. Share of each new reading taken every 12.5 ms. Stock 0.005 at idle rising to 0.1. This is the row for a second bank of cylinders. Stock values are the same as the bank 1 curve. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1126, ledger:E1247</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s used airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4.8" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="13.2" />
      <LABEL index="4" value="21.8" />
      <LABEL index="5" value="29.5" />
      <LABEL index="6" value="40.3" />
      <LABEL index="7" value="51.8" />
      <LABEL index="8" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x259B4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA05" flags="0x30">
    <title>Closed Loop O2 Filter Gain - Purge Feedback Signal, Bank 2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Front O2: filter on the O2 voltage that the canister purge feedback reads, by airflow. Share of each new reading taken every 12.5 ms. Stock 0.005 at idle rising to 0.14. This is the row for a second bank of cylinders. Stock values are the same as the bank 1 curve. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1126, ledger:E1247</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s used airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4.8" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="13.2" />
      <LABEL index="4" value="21.8" />
      <LABEL index="5" value="29.5" />
      <LABEL index="6" value="40.3" />
      <LABEL index="7" value="51.8" />
      <LABEL index="8" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x259DC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA06" flags="0x30">
    <title>Catalyst Monitor - First Fuel Step Commanded EQ, Bank 2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: commanded EQ ratio during the first fuel step, by airflow. Stock 1.10 (10 % rich) everywhere. This is the row for a second bank of cylinders. Stock values are the same as the bank 1 curve. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0445, ledger:E1002, ledger:E1249</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x32952" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>g/s</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3297A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>EQ</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="1+X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA07" flags="0x30">
    <title>Catalyst Monitor - Second Fuel Step Commanded EQ, Bank 2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: commanded EQ ratio during the second fuel step, by airflow. Stock 0.92 at low airflow to 0.93 (7 to 8 % lean). This is the row for a second bank of cylinders. Stock values are the same as the bank 1 curve. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0445, ledger:E1002, ledger:E1249</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x32952" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>g/s</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x329A2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>EQ</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="1+X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA08" flags="0x30">
    <title>Purge Valve Duty vs Flow Demand - 163 to 327 Flow Units</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge: purge valve duty for a purge flow demand between 163 and 327 flow units, continuing the main Purge Valve Duty vs Flow Demand curve (0 to 163); above 655 the duty is 100 %. Stock 100 % in every cell. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0950, ledger:E1122, ledger:E1250</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>flow units demand</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="163" />
      <LABEL index="1" value="168.125" />
      <LABEL index="2" value="173.25" />
      <LABEL index="3" value="178.375" />
      <LABEL index="4" value="183.5" />
      <LABEL index="5" value="188.625" />
      <LABEL index="6" value="193.75" />
      <LABEL index="7" value="198.875" />
      <LABEL index="8" value="204" />
      <LABEL index="9" value="209.125" />
      <LABEL index="10" value="214.25" />
      <LABEL index="11" value="219.375" />
      <LABEL index="12" value="224.5" />
      <LABEL index="13" value="229.625" />
      <LABEL index="14" value="234.75" />
      <LABEL index="15" value="239.875" />
      <LABEL index="16" value="245" />
      <LABEL index="17" value="250.125" />
      <LABEL index="18" value="255.25" />
      <LABEL index="19" value="260.375" />
      <LABEL index="20" value="265.5" />
      <LABEL index="21" value="270.625" />
      <LABEL index="22" value="275.75" />
      <LABEL index="23" value="280.875" />
      <LABEL index="24" value="286" />
      <LABEL index="25" value="291.125" />
      <LABEL index="26" value="296.25" />
      <LABEL index="27" value="301.375" />
      <LABEL index="28" value="306.5" />
      <LABEL index="29" value="311.625" />
      <LABEL index="30" value="316.75" />
      <LABEL index="31" value="321.875" />
      <LABEL index="32" value="327" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2500E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.781250</max>
      <MATH equation="X/326.4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA09" flags="0x30">
    <title>Purge Valve Duty vs Flow Demand - 327 to 655 Flow Units</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge: purge valve duty for a purge flow demand between 327 and 655 flow units, continuing the main Purge Valve Duty vs Flow Demand curve (0 to 163); above 655 the duty is 100 %. Stock 100 % in every cell. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0950, ledger:E1122, ledger:E1250</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>flow units demand</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="327" />
      <LABEL index="1" value="337.25" />
      <LABEL index="2" value="347.5" />
      <LABEL index="3" value="357.75" />
      <LABEL index="4" value="368" />
      <LABEL index="5" value="378.25" />
      <LABEL index="6" value="388.5" />
      <LABEL index="7" value="398.75" />
      <LABEL index="8" value="409" />
      <LABEL index="9" value="419.25" />
      <LABEL index="10" value="429.5" />
      <LABEL index="11" value="439.75" />
      <LABEL index="12" value="450" />
      <LABEL index="13" value="460.25" />
      <LABEL index="14" value="470.5" />
      <LABEL index="15" value="480.75" />
      <LABEL index="16" value="491" />
      <LABEL index="17" value="501.25" />
      <LABEL index="18" value="511.5" />
      <LABEL index="19" value="521.75" />
      <LABEL index="20" value="532" />
      <LABEL index="21" value="542.25" />
      <LABEL index="22" value="552.5" />
      <LABEL index="23" value="562.75" />
      <LABEL index="24" value="573" />
      <LABEL index="25" value="583.25" />
      <LABEL index="26" value="593.5" />
      <LABEL index="27" value="603.75" />
      <LABEL index="28" value="614" />
      <LABEL index="29" value="624.25" />
      <LABEL index="30" value="634.5" />
      <LABEL index="31" value="644.75" />
      <LABEL index="32" value="655" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25056" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.781250</max>
      <MATH equation="X/326.4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xA0A" flags="0x0">
    <title>P2138 Pedal Position Sensor Correlation - Failed Samples to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2138: the PCM compares the two accelerator pedal position sensors. Once a sample has failed, the test counts samples; the code sets when this many have failed before the sample window is reached. Stock 15. Effect: raise = more failed samples are needed to set the code Evidence: ledger:E0434, ledger:E1251</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B74" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA0B" flags="0x0">
    <title>P2138 Pedal Position Sensor Correlation - Consecutive Failed Samples to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2138: the PCM compares the two accelerator pedal position sensors. The code also sets when this many samples in a row have failed. Stock 12. Effect: raise = a longer run of failed samples is needed Evidence: ledger:E0434, ledger:E1251</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B80" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA0C" flags="0x0">
    <title>P2138 Pedal Position Sensor Correlation - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2138: the PCM compares the two accelerator pedal position sensors. Counted from the first failed sample: when this many samples are reached without the code setting, both counts start again. Stock 35. Effect: raise = failures are collected over a longer window Evidence: ledger:E0434, ledger:E1251</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B84" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA0D" flags="0x0">
    <title>P2138 Pedal Position Sensor Correlation - Allowed Difference, Share of Lower Reading</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2138: the PCM compares the two accelerator pedal position sensors. The allowed difference between the two readings is this share of the lower reading plus a fixed part; a larger difference counts as a failed sample. Stock 5.00 %. Effect: raise = a larger difference is tolerated Evidence: ledger:E0434, ledger:E1251</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B7C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA0E" flags="0x0">
    <title>P2135 Throttle Position Sensor Correlation - Failed Samples to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2135: the PCM compares the two throttle position sensors. Once a sample has failed, the test counts samples; the code sets when this many have failed before the sample window is reached. Stock 15. Effect: raise = more failed samples are needed to set the code Evidence: ledger:E0434, ledger:E1252</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23C3C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA0F" flags="0x0">
    <title>P2135 Throttle Position Sensor Correlation - Consecutive Failed Samples to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2135: the PCM compares the two throttle position sensors. The code also sets when this many samples in a row have failed. Stock 12. Effect: raise = a longer run of failed samples is needed Evidence: ledger:E0434, ledger:E1252</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23C3E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA10" flags="0x0">
    <title>P2135 Throttle Position Sensor Correlation - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2135: the PCM compares the two throttle position sensors. Counted from the first failed sample: when this many samples are reached without the code setting, both counts start again. Stock 35. Effect: raise = failures are collected over a longer window Evidence: ledger:E0434, ledger:E1252</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23C40" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA11" flags="0x0">
    <title>P2135 Throttle Position Sensor Correlation - Allowed Difference, Share of Lower Reading</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2135: the PCM compares the two throttle position sensors. The allowed difference between the two readings is this share of the lower reading plus a fixed part; a larger difference counts as a failed sample. Stock 4.98 %. Effect: raise = a larger difference is tolerated Evidence: ledger:E0434, ledger:E1252</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23C36" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xA12" flags="0x30">
    <title>Catalyst Monitor Enable - Minimum O2 Switches During Trim Averaging</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): the upstream O2 sensor must change between rich and lean at least this many times during the short term trim sampling time, or the test stops for this run (one value per catalyst). This truck has one bank and uses the first value; the second is for a second bank and has no effect on the stock calibration (dormant). Stock 4. Effect: raise = the test needs more O2 switching before it goes on Evidence: ledger:E0437, ledger:E1188, ledger:E1254</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>catalyst</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x32920" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>switches</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xA13" flags="0x0">
    <title>High-Load Monitor - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. High-load monitor: once the time spent at high load (intake vacuum below the threshold) passes this, the monitor sets its flag and acts. Stock 10.0 s. Effect: raise = longer at high load before the monitor acts Evidence: ledger:E0775, ledger:E1265</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23C58" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xA14" flags="0x30">
    <title>Shift Torque Reduction Profile - Ratio End</title>
    <description>Change in small steps and log. Each row is [COUNT=17][17 points]; the count word is structure, never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Measured gear ratio at which the shift torque reduction has fully ramped in, by shift and shift torque. Stock: 0 everywhere except the 1-3 shift at 0 Nm (2.20). Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0365, ledger:E0706, ledger:E1266, ledger:E1295</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3E420" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT; data columns: Nm (shift torque))</units>
      <embedinfo type="1" />
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-3 shift" />
      <LABEL index="1" value="1-4 shift" />
      <LABEL index="2" value="into 1st (and 2-4)" />
      <LABEL index="3" value="into 2nd" />
      <LABEL index="4" value="into 3rd" />
      <LABEL index="5" value="into 4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EE74" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xA15" flags="0x0">
    <title>Crank Wheel - Reference Events per Revolution (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of crank reference events per crankshaft revolution (one every 12 teeth), used to turn the reference event period into engine speed. Stock 5. Reference only: DO NOT EDIT. Effect: reference only (crank wheel geometry) Evidence: ledger:E0324, ledger:E1274, ledger:E1276</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x23A0C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>events per revolution</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA16" flags="0x0">
    <title>Engine Stopped Detection - Time Without Crank Signal</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When no crank reference event arrives for this long, the engine speed it measures is set to zero (the engine counts as stopped). Stock 4 s. Effect: raise = the PCM waits longer without crank signal before reporting the engine stopped Evidence: ledger:E0324, ledger:E1274, ledger:E1276</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x23A1A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA17" flags="0x0">
    <title>Cam Sensor Fault Start - Running Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cranking strategy for a failed cam sensor: above this engine speed the engine counts as running, and once it has run for the running time below the strategy stops for this start. Stock 300 rpm. Effect: raise = the engine must reach a higher speed before the cam fault cranking strategy stands down Evidence: ledger:E0324, ledger:E1274, ledger:E1275</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x23AD8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xA18" flags="0x30">
    <title>Airmass Predictor - Feedback Gain on Previous Estimate (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Multiplies the previous airmass estimate and adds it to the new prediction (1.0 = full carry-over). Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C31A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA19" flags="0x30">
    <title>Airmass Predictor - Gain on MAF Airmass (current sample) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Multiplies the current MAF cylinder airmass sample in the prediction. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C33E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-1.000000</min>
      <max>0.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA1A" flags="0x30">
    <title>Airmass Predictor - Blend Toward Prediction (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Fraction of the way from the prediction to the filtered MAF airmass that the airmass estimate takes (0 = prediction only, 1.0 = filtered MAF airmass only). Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277, ledger:E1521</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C362" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA1B" flags="0x30">
    <title>Airmass Predictor - Gain on MAF Airmass (previous sample) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Multiplies the previous MAF cylinder airmass sample in the prediction. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C386" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-1.000000</min>
      <max>0.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA1C" flags="0x30">
    <title>Airmass Predictor - Gain on MAP (current sample) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Cylinder airmass added per kPa of the current MAP sample. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C3AA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mg/cyl per kPa</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA1D" flags="0x30">
    <title>Airmass Predictor - Gain on MAP (one sample back) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Cylinder airmass added per kPa of the MAP sample one step back. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C3CE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mg/cyl per kPa</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA1E" flags="0x30">
    <title>Airmass Predictor - Gain on MAP (two samples back) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Cylinder airmass added per kPa of the MAP sample two steps back. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C3F2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mg/cyl per kPa</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA1F" flags="0x30">
    <title>Airmass Predictor - Gain on Throttle Area (current sample) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Cylinder airmass added per % of the current throttle area sample. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C416" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mg/cyl per %</units>
      <decimalpl>0</decimalpl>
      <min>-40.960000</min>
      <max>40.958750</max>
      <MATH equation="X/800"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA20" flags="0x30">
    <title>Airmass Predictor - Gain on Throttle Area (one sample back) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Cylinder airmass added per % of the throttle area sample one step back. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C43A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mg/cyl per %</units>
      <decimalpl>0</decimalpl>
      <min>-40.960000</min>
      <max>40.958750</max>
      <MATH equation="X/800"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA21" flags="0x30">
    <title>Airmass Predictor - Gain on Throttle Area (two samples back) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Cylinder airmass added per % of the throttle area sample two steps back. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C45E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mg/cyl per %</units>
      <decimalpl>0</decimalpl>
      <min>-40.960000</min>
      <max>40.958750</max>
      <MATH equation="X/800"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA22" flags="0x30">
    <title>TCC Adapt - Learn Cell Torque Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque of each of the five learn cells. Part of converter clutch adaptive learning: while the clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells spread over engine torque. Axis data: keep ascending. Effect: moves the learn cells along engine torque Evidence: ledger:E0376, ledger:E1283</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>learn cell</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CE82" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA23" flags="0x30">
    <title>TCC Adapt - Learn Cell Weight vs Torque</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How much each learn cell (rows) takes of a learning step, by engine torque (columns). Stock: 1.0 at the cell&#x27;s own torque, 0.5 at the neighbouring ones, 0 further away. Part of converter clutch adaptive learning: while the clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells spread over engine torque. Effect: raise = that cell learns more at that torque Evidence: ledger:E0376, ledger:E1283</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3CE80" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>6</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT; data columns: Nm)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>learn cell</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CE42" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>weight</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA24" flags="0x30">
    <title>TCC Adapt - Learning Gain vs Cell Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learning gain applied to a cell, by that cell&#x27;s weight (0 to 1.0). Stock linear (gain = weight). Part of converter clutch adaptive learning: while the clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells spread over engine torque. Effect: raise = faster converter clutch learning at that weight Evidence: ledger:E0376, ledger:E1283</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>weight</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.25" />
      <LABEL index="2" value="0.5" />
      <LABEL index="3" value="0.75" />
      <LABEL index="4" value="1.0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CDBE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xA25" flags="0x0">
    <title>TCC Adapt - Filter Gain, Slip Controller State</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain for the slip controller state used by the learning steadiness checks (stock 0.005 per update). Part of converter clutch adaptive learning: while the clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells spread over engine torque. Effect: raise = the filtered value follows the controller state faster Evidence: ledger:E0376, ledger:E1283</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CD98" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA26" flags="0x0">
    <title>TCC Adapt - Filter Gain, Engine Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain for the engine torque used to pick the learn cell and to check that torque is steady (stock 0.1 per update). Part of converter clutch adaptive learning: while the clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells spread over engine torque. Effect: raise = the filtered torque follows engine torque faster Evidence: ledger:E0376, ledger:E1283</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CD9A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA27" flags="0x0">
    <title>TCC Adapt - Filter Gain, Throttle Area</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain for the throttle area used by the learning steadiness checks (stock 0.005 per update). Part of converter clutch adaptive learning: while the clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells spread over engine torque. Effect: raise = the filtered throttle follows the throttle faster Evidence: ledger:E0376, ledger:E1283</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CD9C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA28" flags="0x0">
    <title>TCC Adapt - Minimum Learning Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A learned pressure offset cell is only changed when the learning step is larger than this (stock 0.69 kPa). Part of converter clutch adaptive learning: while the clutch is applied and conditions are steady, the PCM learns a pressure offset in five cells across 50 to 210 Nm and adds it to the load based clutch pressure. Effect: raise = small corrections are ignored (learning moves less often) Evidence: ledger:E0376, ledger:E1283, ledger:E1427</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CD8A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>2047.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xA29" flags="0x30">
    <title>TCC Feed-Forward - Torque Rate Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque rate breakpoints (0 to 98 Nm/s) of the rising and falling feed-forward gains. Axis data: keep ascending. Part of the converter clutch slip controller&#x27;s feed-forward: while engine torque rises faster than the rise threshold, if clutch pressure is climbing faster than the allowed rise for that torque increase, the controller pulls the pressure back by the excess (times the rising gain). Effect: moves the feed-forward gain points along torque rate Evidence: ledger:E1201, ledger:E1284, ledger:E1471</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CE94" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm/s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1999.969482</max>
      <MATH equation="X/32.768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xA2A" flags="0x0">
    <title>TCC Feed-Forward - Long Torque Rate Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Length of the longer window over which the engine torque rate is measured (stock 1024 ms). Part of the converter clutch slip controller&#x27;s feed-forward: when engine torque changes quickly, the controller state gets an extra term sized by the torque rate. Effect: raise = slower, smoother long-window torque rate Evidence: ledger:E1201, ledger:E1284</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D192" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ms</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xA2B" flags="0x30">
    <title>Shift Pressure Multiplier - Torque Ratio Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Ratio of transmission input torque to the shift torque adder (0 to 4.0): row breakpoints of the shift pressure multiplier tables. Axis data: keep ascending. Effect: moves the table points it indexes Evidence: ledger:E0710, ledger:E1287</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E3C0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA2C" flags="0x30">
    <title>Garage Shift Pressure Adder - Speed Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed (transmission side, 0 to 20 km/h): row breakpoints of the garage shift pressure adder. Axis data: keep ascending. Effect: moves the table points it indexes Evidence: ledger:E0338, ledger:E1287</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37EDA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xA2D" flags="0x0">
    <title>TCC Release - Cold Trans Fluid, On Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this transmission fluid temperature the converter clutch is released (stock 18 C). The torque converter clutch is released while any release condition is active. Effect: raise = the clutch stays released up to a warmer fluid temperature Evidence: ledger:E1289</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D1FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA2E" flags="0x0">
    <title>TCC Release - Cold Trans Fluid, Off Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this transmission fluid temperature the cold fluid release ends (stock 20 C; between the two the last state holds). The torque converter clutch is released while any release condition is active. Effect: raise = the cold fluid release lasts to a warmer temperature Evidence: ledger:E1289</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D1FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA2F" flags="0x0">
    <title>TCC Release - Cold Coolant, On Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this engine coolant temperature the converter clutch is released (stock 58 C). The torque converter clutch is released while any release condition is active. Effect: raise = the clutch stays released up to a warmer coolant temperature Evidence: ledger:E1289</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D204" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA30" flags="0x0">
    <title>TCC Release - Cold Coolant, Off Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this engine coolant temperature the cold coolant release ends (stock 60 C; between the two the last state holds). The torque converter clutch is released while any release condition is active. Effect: raise = the cold coolant release lasts to a warmer temperature Evidence: ledger:E1289</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D206" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA31" flags="0x0">
    <title>TCC Release - Low Baro in 1st / 2nd, On Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In 1st and 2nd gear, below this barometric pressure the converter clutch is released (stock 0 kPa: never). The torque converter clutch is released while any release condition is active. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = release at altitude in 1st / 2nd) Evidence: ledger:E1289</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D20C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA32" flags="0x0">
    <title>TCC Release - Low Baro in 1st / 2nd, Off Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this barometric pressure the low baro release ends (stock 0 kPa). The torque converter clutch is released while any release condition is active. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1289</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D20E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA33" flags="0x0">
    <title>Shift Sol Ratio Tests (P0751 / P0752 / P0756 / P0757) - Run Condition, Input Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The four shift solenoid performance tests run only with transmission input speed at or above this. Stock 0 rpm (no limit). Effect: raise = the tests need more input speed Evidence: ledger:E1291</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F574" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA34" flags="0x0">
    <title>Shift Sol Ratio Tests (P0751 / P0752 / P0756 / P0757) - Run Condition, Input Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The four shift solenoid performance tests run only with transmission input speed at or below this. Stock 8191.75 rpm (no limit). Effect: lower = the tests stop above a lower input speed Evidence: ledger:E1291</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F576" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA35" flags="0x0">
    <title>Scan Tool Gear Command - 3-2 Request, Max Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A scan tool request for 2nd gear while in 3rd is refused above this vehicle speed. Stock 140 km/h. Effect: lower = a commanded 3-2 is refused at lower speeds Evidence: ledger:E1292</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F4FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA36" flags="0x0">
    <title>Scan Tool Gear Command - 2-1 Request, Max Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A scan tool request for 1st gear while in 2nd is refused above this vehicle speed. Stock 65 km/h. Effect: lower = a commanded 2-1 is refused at lower speeds Evidence: ledger:E1292</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F4FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA37" flags="0x0">
    <title>Scan Tool Gear Command - Max Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Any scan tool gear request is refused above this vehicle speed. Stock 180 km/h. Effect: lower = gear commands are refused at lower speeds Evidence: ledger:E1292</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F500" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA38" flags="0x0">
    <title>Scan Tool Gear Command - Max Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Any scan tool gear request is refused above this engine speed. Stock 6250 rpm. Effect: lower = gear commands are refused at lower engine speeds Evidence: ledger:E1292</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F502" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA39" flags="0x0">
    <title>P0503 Test - Run Condition, Input Speed Step Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): the check runs only while transmission input speed changes by no more than this between two 25 ms samples; a larger step stops it for that sample and restarts the steady time. Stock 500 rpm. Effect: lower = the check is suspended by smaller input speed changes Evidence: ledger:E1293</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F83E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA3A" flags="0x0">
    <title>P0503 Test - Run Condition, Input Speed Steady Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): time the input speed must stay steady (see the step maximum) before the check runs. Stock 0 s (at once). Effect: raise = the check waits longer after an input speed step Evidence: ledger:E1293</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F84A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA3B" flags="0x0">
    <title>P0503 Test - Run Condition, Time in Range</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): time the selector must have stayed in the present range before the check runs. Stock 0 s (no wait). Effect: raise = the check waits longer after a range change Evidence: ledger:E1293</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F84E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA3C" flags="0x0">
    <title>Range Switch Checks (P1815) - Run Condition, Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1815 (engine started with the range switch not in park or neutral) and the range switch circuit checks run only with system voltage at or below this. Stock 18 V. Effect: lower = the checks stop at a lower system voltage Evidence: ledger:E1294</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F85E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA3D" flags="0x0">
    <title>Range Switch Checks (P1815) - Run Condition, Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1815 (engine started with the range switch not in park or neutral) and the range switch circuit checks run only with system voltage at or above this. Stock 6.5 V. Effect: raise = the checks need a higher system voltage Evidence: ledger:E1294</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F860" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA3E" flags="0x0">
    <title>TCC Engine Torque Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How quickly the filtered engine torque used by the converter clutch logic (slip target lookup and applied slip learning) follows each new value: the fraction of the change taken per update. Stock 0.30. Effect: raise = the filtered torque follows changes faster but is noisier; lower = smoother but lags more Evidence: ledger:E1296</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D49A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA3F" flags="0x0">
    <title>TCC Tip-In Release - High Speed Set, Speed Above (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this transmission output side speed the tip-in release uses its high speed rate thresholds and hold times (the items marked above 255 km/h); at or below it, the normal set. Stock 255 km/h, so the high speed set is never used. TCC tip-in release: when the throttle request rises faster than the rate threshold, the PCM releases the converter clutch for the hold time. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: no effect on stock (inactive); lower = the high speed set applies above this speed Evidence: ledger:E1296</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D48C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA40" flags="0x0">
    <title>2-1 Downshift Closed Throttle Mode - Throttle Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The 2-1 downshift uses its closed-throttle mode when throttle is below this and the speed is below the closed-throttle speed. Stock 2.5 %. Applies at the start of a 2-1 downshift (from 2nd with a downshift commanded); in this closed-throttle mode the 2-1 downshift pressure command is zero. Effect: raise = more part-throttle 2-1 downshifts use the closed-throttle mode Evidence: ledger:E1298</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x375C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA41" flags="0x0">
    <title>2-1 Downshift Closed Throttle Mode - Speed Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The 2-1 downshift uses its closed-throttle mode when vehicle speed at the start of the downshift is below this and throttle is below the closed-throttle throttle. Stock 20.5 mph (33 km/h). Applies at the start of a 2-1 downshift (from 2nd with a downshift commanded); in this closed-throttle mode the 2-1 downshift pressure command is zero. Effect: raise = closed-throttle 2-1 downshifts at higher speeds use the closed-throttle mode Evidence: ledger:E1298</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x375CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>mph</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>318.137196</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/205.996032"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA42" flags="0x0">
    <title>Force Motor Current Control - Maximum Duty</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest PWM duty the current loop may command (stock 95 %). The force motor (pressure control solenoid) current loop corrects the solenoid PWM duty every update so the measured current follows the desired current. Effect: raise = the solenoid can be driven harder to reach a high current request Evidence: ledger:E1299</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E1E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA43" flags="0x0">
    <title>Force Motor Current Control - Minimum Duty</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest PWM duty the current loop may command (stock 5 %). The force motor (pressure control solenoid) current loop corrects the solenoid PWM duty every update so the measured current follows the desired current. Effect: lower = the solenoid current can be taken closer to zero Evidence: ledger:E1299</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E1EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA44" flags="0x0">
    <title>Shift Pressure Hand-Over Margin - Upshift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Margin used during an upshift (stock 600 kPa). The force motor is commanded either with the shift pressure or with normal line pressure; during shift pressure control the shift pressure is used while line pressure is below shift pressure plus this margin, and line pressure is used once it reaches it. Effect: raise = shift pressure stays in control against a higher line pressure during upshifts Evidence: ledger:E1299</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E23A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA45" flags="0x0">
    <title>Shift Pressure Hand-Over Margin - Other Shifts</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Margin used outside an upshift (stock 622 kPa); the closed-throttle and table modes of the 2-1 downshift use shift pressure without this check. The force motor is commanded either with the shift pressure or with normal line pressure; during shift pressure control the shift pressure is used while line pressure is below shift pressure plus this margin, and line pressure is used once it reaches it. Effect: raise = shift pressure stays in control against a higher line pressure on other shifts Evidence: ledger:E1299</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E232" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA46" flags="0x0">
    <title>Trans-Side Vehicle Speed - Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain for the vehicle speed the transmission computes from output shaft speed, tire size and axle ratio (stock 0.1 per update); the filtered speed is the one the shift and converter clutch logic use. Effect: raise = the transmission&#x27;s speed follows changes faster (less smoothing) Evidence: ledger:E1299</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF3E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA47" flags="0x0">
    <title>Trans-Side Vehicle Acceleration - Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain for trans-side vehicle acceleration, updated every 100 ms (stock 0.1 per update). Smoothed trans-side vehicle acceleration sets an accelerating flag read by the shift and converter clutch logic; between the on and off values the flag keeps its last state. Effect: raise = the acceleration and its flag react faster Evidence: ledger:E1299</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF40" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xA48" flags="0x30">
    <title>Accelerating Flag - On Above, by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Acceleration above which the flag sets, for 1st to 3rd gear (stock -255 / 2.0 / 1.0: always on in 1st). Smoothed trans-side vehicle acceleration sets an accelerating flag read by the shift and converter clutch logic; between the on and off values the flag keeps its last state. In 4th gear the code reads one value past this list (for the on value the 1st gear off value, for the off value the deceleration filter gain), so on the stock calibration the flag stays on in 4th. Effect: raise = the flag needs harder acceleration to set in that gear Evidence: ledger:E1299</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DF44" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per s</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA49" flags="0x30">
    <title>Accelerating Flag - Off Below, by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Acceleration below which the flag clears, for 1st to 3rd gear (stock -255 / 0.6 / 0.6). Smoothed trans-side vehicle acceleration sets an accelerating flag read by the shift and converter clutch logic; between the on and off values the flag keeps its last state. In 4th gear the code reads one value past this list (for the on value the 1st gear off value, for the off value the deceleration filter gain), so on the stock calibration the flag stays on in 4th. Effect: raise = the flag clears sooner as acceleration falls Evidence: ledger:E1299</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DF4A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per s</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xA4A" flags="0x0">
    <title>Deceleration Flag - Acceleration Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain for the acceleration the deceleration flag checks (stock 0.1 per update). A deceleration flag, read by the shift and converter clutch logic, is set while smoothed trans-side vehicle acceleration is below the lower limit or above the upper limit for the next gear down. Effect: raise = the deceleration flag reacts faster Evidence: ledger:E1299</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF50" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xA4B" flags="0x30">
    <title>Deceleration Flag - Upper Acceleration Limit by Target Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this acceleration the flag also sets (stock 255 km/h per s: never). A deceleration flag, read by the shift and converter clutch logic, is set while smoothed trans-side vehicle acceleration is below the lower limit or above the upper limit for the next gear down. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (lower = the flag also sets under strong acceleration) Evidence: ledger:E1299</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>target gear</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DF52" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per s</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA4C" flags="0x30">
    <title>Deceleration Flag - Lower Acceleration Limit by Target Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this acceleration the flag sets (stock 0: any deceleration). A deceleration flag, read by the shift and converter clutch logic, is set while smoothed trans-side vehicle acceleration is below the lower limit or above the upper limit for the next gear down. Effect: raise = the flag also sets at mild acceleration; lower = only firm deceleration sets it Evidence: ledger:E1299</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>target gear</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DF58" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per s</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xA4D" flags="0x0">
    <title>TCC Release - Hot Trans Fluid, On Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this transmission fluid temperature the hot fluid condition turns on (stock 256 C: never). When both the hot fluid and the low speed conditions hold, the converter clutch is kept released, or ramped off if it is applied. This has no effect on the stock calibration (dormant: the stock fluid thresholds are never reached). Effect: no effect on the stock calibration (lower = release the clutch at low speed once the fluid is this hot) Evidence: ledger:E1300</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D202" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA4E" flags="0x0">
    <title>TCC Release - Hot Trans Fluid, Off Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this transmission fluid temperature the hot fluid condition turns off (stock 256 C; between the two the last state holds). When both the hot fluid and the low speed conditions hold, the converter clutch is kept released, or ramped off if it is applied. This has no effect on the stock calibration (dormant: the stock fluid thresholds are never reached). Effect: no effect on the stock calibration Evidence: ledger:E1300</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D200" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA4F" flags="0x0">
    <title>TCC Release - Hot Fluid Speed Window, On Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this vehicle speed the low speed condition of the hot fluid release turns on (stock 109 km/h). When both the hot fluid and the low speed conditions hold, the converter clutch is kept released, or ramped off if it is applied. This has no effect on the stock calibration (dormant: the stock fluid thresholds are never reached). Effect: no effect on the stock calibration (raise = the hot fluid release also applies at higher speed) Evidence: ledger:E1300</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D210" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA50" flags="0x0">
    <title>TCC Release - Hot Fluid Speed Window, Off Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this vehicle speed the low speed condition of the hot fluid release turns off (stock 109 km/h). When both the hot fluid and the low speed conditions hold, the converter clutch is kept released, or ramped off if it is applied. This has no effect on the stock calibration (dormant: the stock fluid thresholds are never reached). Effect: no effect on the stock calibration Evidence: ledger:E1300</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D212" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA51" flags="0x0">
    <title>Cold Weather Shift Offset - Very Cold Air Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During the first 30 seconds of engine run, intake air temperature below this selects the very cold air pair of fluid temperatures for the cold weather offset. Stock -255 C: never. The cold weather offset adds an offset to the shift points and to the converter clutch apply and release points, weighted from full to none by transmission fluid temperature. It applies only in the normal shift mode with a working fluid temperature sensor, and once the fluid reaches the none temperature it stays off until the next key cycle. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no ef...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCFC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA52" flags="0x0">
    <title>Cold Weather Shift Offset - Cold Air Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During the first 30 seconds of engine run, intake air temperature at or above the very cold limit but below this selects the cold air pair of fluid temperatures; at or above it there is no cold weather offset. Stock -255 C: never. The cold weather offset adds an offset to the shift points and to the converter clutch apply and release points, weighted from full to none by transmission fluid temperature. It applies only in the normal shift mode with a working fluid temperature sensor, and once the fluid reaches the none temperature it stays off until the next key cycle. Inactive on the 2006 H3. Whether it is active on this oper...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCFE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA53" flags="0x0">
    <title>Cold Weather Shift Offset, Very Cold Air - Full Below (fluid temp)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With very cold intake air, at or below this transmission fluid temperature the full cold weather offset applies. Stock -255 C. The cold weather offset adds an offset to the shift points and to the converter clutch apply and release points, weighted from full to none by transmission fluid temperature. It applies only in the normal shift mode with a working fluid temperature sensor, and once the fluid reaches the none temperature it stays off until the next key cycle. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1301</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCF8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA54" flags="0x0">
    <title>Cold Weather Shift Offset, Very Cold Air - None Above (fluid temp)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With very cold intake air, the cold weather offset fades linearly to none as transmission fluid temperature rises to this, and ends here. Stock -255 C. The cold weather offset adds an offset to the shift points and to the converter clutch apply and release points, weighted from full to none by transmission fluid temperature. It applies only in the normal shift mode with a working fluid temperature sensor, and once the fluid reaches the none temperature it stays off until the next key cycle. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibratio...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCFA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA55" flags="0x0">
    <title>Cold Weather Shift Offset, Cold Air - Full Below (fluid temp)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With cold intake air, at or below this transmission fluid temperature the full cold weather offset applies. Stock -255 C. The cold weather offset adds an offset to the shift points and to the converter clutch apply and release points, weighted from full to none by transmission fluid temperature. It applies only in the normal shift mode with a working fluid temperature sensor, and once the fluid reaches the none temperature it stays off until the next key cycle. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1301</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCF4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA56" flags="0x0">
    <title>Cold Weather Shift Offset, Cold Air - None Above (fluid temp)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With cold intake air, the cold weather offset fades linearly to none as transmission fluid temperature rises to this, and ends here. Stock -255 C. The cold weather offset adds an offset to the shift points and to the converter clutch apply and release points, weighted from full to none by transmission fluid temperature. It applies only in the normal shift mode with a working fluid temperature sensor, and once the fluid reaches the none temperature it stays off until the next key cycle. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evi...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCF6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA57" flags="0x0">
    <title>Cold Fluid 4th Gear Inhibit - On Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this transmission fluid temperature a commanded 4th gear is stepped down to 3rd. Stock -255 C: never. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (raise = no 4th gear until the fluid warms) Evidence: ledger:E1301</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DD2A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA58" flags="0x0">
    <title>Cold Fluid 4th Gear Inhibit - Off Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this transmission fluid temperature the cold fluid 4th gear inhibit ends (between the two the last state holds). Stock -255 C. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1301</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DD2C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA59" flags="0x0">
    <title>Trans Hot Mode, Rapid Rise - Arm At or Above (fluid temp) (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rapid rise hot mode starts when transmission fluid temperature is at or above this and rising at least as fast as the rapid rise rate limit for that temperature; it ends whenever the fluid falls below this. Stock 110.3 C. Rapid rise hot mode is a second way into transmission hot mode (hot shift and converter clutch schedules) when the fluid temperature climbs quickly; it is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1301</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DDD6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA5A" flags="0x0">
    <title>Trans Hot Mode, Rapid Rise - Leave Below After Minimum Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the hot mode minimum time has passed, rapid rise hot mode ends when transmission fluid temperature is below this. Stock 123.0 C. Rapid rise hot mode is a second way into transmission hot mode (hot shift and converter clutch schedules) when the fluid temperature climbs quickly; it is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1301</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DDE0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA5B" flags="0x0">
    <title>Trans Fluid Temp Substitute - Cold Intake Air Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intake air temperature below this adds the Cold Intake Air Adder to the estimated fluid temperature. Stock -256 C: never. Used only when the fluid temperature sensor has a fault and the fluid temperature is estimated from coolant temperature (coolant between the very cold and hot engine thresholds, after the early run time). While the transmission range switch reading is invalid the substitute is the Invalid Range Switch Value (stock 141 C) instead of this estimate. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1301,...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEC8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA5C" flags="0x0">
    <title>Trans Fluid Temp Substitute - Warm Intake Air Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intake air temperature above this adds the Warm Intake Air Adder to the estimated fluid temperature. Stock 256 C: never. Used only when the fluid temperature sensor has a fault and the fluid temperature is estimated from coolant temperature (coolant between the very cold and hot engine thresholds, after the early run time). While the transmission range switch reading is invalid the substitute is the Invalid Range Switch Value (stock 141 C) instead of this estimate. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1301,...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DECC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA5D" flags="0x0">
    <title>TCC Release - Closed Throttle, Low Speed On Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this vehicle speed the low speed throttle window applies to the closed throttle release (stock 30 km/h). The converter clutch is released while the closed throttle condition is active (where enabled for the current range and gear). Effect: raise = the low speed closed throttle release applies up to a higher speed Evidence: ledger:E1302</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D3FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA5E" flags="0x0">
    <title>TCC Release - Closed Throttle, Low Speed Off Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this vehicle speed the low speed window ends and the higher speed throttle window applies (stock 31 km/h; between the two the last state holds). The converter clutch is released while the closed throttle condition is active (where enabled for the current range and gear). Effect: raise = the low speed window lasts to a higher speed Evidence: ledger:E1302</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D3FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA5F" flags="0x0">
    <title>TCC Release - Closed Throttle at Low Speed, On Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At low speed, below this throttle the closed throttle release turns on (stock 5 %). The converter clutch is released while the closed throttle condition is active (where enabled for the current range and gear). Effect: raise = the clutch releases at low speed with more throttle still applied Evidence: ledger:E1302</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D21C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA60" flags="0x0">
    <title>TCC Release - Closed Throttle at Low Speed, Off Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At low speed, above this throttle the closed throttle release turns off (stock 7 %; between the two the last state holds). The converter clutch is released while the closed throttle condition is active (where enabled for the current range and gear). Effect: raise = more throttle is needed to end the low speed release Evidence: ledger:E1302</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D21E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA61" flags="0x0">
    <title>TCC Release - Negative Slip, On Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter slip (engine speed minus transmission input speed) below this value turns the negative slip release on when no shift is in progress (stock -4000 rpm). The converter clutch is released while it is on. Effect: raise toward 0 = the clutch releases with less negative slip (less coasting overrun) Evidence: ledger:E1303</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D22C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA62" flags="0x0">
    <title>TCC Release - Negative Slip, Off Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter slip above this value turns the negative slip release off (stock 50 rpm; between the two the last state holds). Effect: lower = the negative slip release ends sooner Evidence: ledger:E1303</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D22E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA63" flags="0x0">
    <title>TCC Release - Fast Throttle Closing Rate A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle closing faster than this rate (negative = closing) releases the converter clutch and starts hold time A (stock -1000 %/s). Checks A and B run in different clutch control states, each with its own rate and hold time. Effect: raise toward 0 = a slower throttle lift already releases the clutch Evidence: ledger:E1304</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D234" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>%/s</units>
    <decimalpl>2</decimalpl>
    <min>-3200.000000</min>
    <max>3199.902344</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10.24"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA64" flags="0x0">
    <title>TCC Release - Fast Throttle Closing Hold Time A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a fast throttle closing (check A) the converter clutch is held released for this time (stock 2.0 s). Effect: raise = the clutch stays released longer after a fast lift Evidence: ledger:E1304</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D27A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA65" flags="0x0">
    <title>TCC Release - Fast Throttle Closing Rate B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle closing faster than this rate (negative = closing) releases the converter clutch and starts hold time B (stock -1000 %/s). Checks A and B run in different clutch control states, each with its own rate and hold time. Effect: raise toward 0 = a slower throttle lift already releases the clutch Evidence: ledger:E1304</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D238" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>%/s</units>
    <decimalpl>2</decimalpl>
    <min>-3200.000000</min>
    <max>3199.902344</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10.24"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA66" flags="0x0">
    <title>TCC Release - Fast Throttle Closing Hold Time B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a fast throttle closing (check B) the converter clutch is held released for this time (stock 0.5 s). Effect: raise = the clutch stays released longer after a fast lift Evidence: ledger:E1304</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D27C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA67" flags="0x0">
    <title>Trans Fluid Temp Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How quickly the filtered transmission fluid temperature follows the fluid temperature reading, as the fraction of the difference taken per update. The filtered value is the fluid temperature the transmission logic uses (hot mode, converter clutch release conditions, shift schedules). Stock 0.75. Effect: raise = the fluid temperature the logic uses reacts faster but is noisier; lower = smoother but lags more Evidence: ledger:E1305</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEB2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA68" flags="0x0">
    <title>Trans Fluid Temp Tracker - Level Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of the difference between the fluid temperature reading and the tracked temperature added to the tracked level each update. Stock 0.224. The fluid temperature tracker follows the fluid temperature reading with a level and a rate of rise; the tracked level is recorded as the fluid temperature at engine start, and the rate feeds the rapid rise hot mode check. Effect: raise = the tracked fluid temperature follows the reading faster Evidence: ledger:E1305</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEB4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA69" flags="0x0">
    <title>Trans Fluid Temp Tracker - Rate Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How strongly each difference between the fluid temperature reading and the tracked temperature changes the tracked rate of rise. Stock 1.125. The fluid temperature tracker follows the fluid temperature reading with a level and a rate of rise; the tracked level is recorded as the fluid temperature at engine start, and the rate feeds the rapid rise hot mode check. Effect: raise = the tracked rate of rise reacts faster but is noisier Evidence: ledger:E1305</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEB6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA6A" flags="0x0">
    <title>Output Shaft Speed Tracker - Speed Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of the speed error added to the tracked output shaft speed each update. Stock 0.277. The output shaft speed tracker follows the output speed sensor with three estimates (speed, rate of change and acceleration), each corrected by its share of the speed error every update; the rate of change estimate is used by the shift and converter clutch logic. Effect: raise = the tracked speed follows the sensor faster but passes more noise Evidence: ledger:E1305</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF12" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA6B" flags="0x0">
    <title>Output Shaft Speed Tracker - Rate Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of the speed error added to the tracked rate of change of output shaft speed each update. Stock 1.369. The output shaft speed tracker follows the output speed sensor with three estimates (speed, rate of change and acceleration), each corrected by its share of the speed error every update; the rate of change estimate is used by the shift and converter clutch logic. Effect: raise = the output speed rate of change reacts faster but is noisier Evidence: ledger:E1305</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF14" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA6C" flags="0x0">
    <title>Output Shaft Speed Tracker - Acceleration Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of the speed error added to the tracked output shaft acceleration each update. Stock 0.615. The output shaft speed tracker follows the output speed sensor with three estimates (speed, rate of change and acceleration), each corrected by its share of the speed error every update; the rate of change estimate is used by the shift and converter clutch logic. Effect: raise = the tracked acceleration reacts faster but is noisier Evidence: ledger:E1305</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF16" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA6D" flags="0x0">
    <title>Output Shaft Speed Change Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How quickly the filtered change of output shaft speed per update follows each new measurement, as the fraction of the difference taken per update. Stock 0.10. Effect: raise = the filtered speed change reacts faster but is noisier Evidence: ledger:E1305</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF18" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA6E" flags="0x0">
    <title>TCC Closed Throttle Apply - Throttle Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this throttle the closed throttle apply state of the converter clutch can be entered from the applied states, and its slip check runs (stock 0.75 %). The state is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1306</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CD00" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA6F" flags="0x0">
    <title>TCC Closed Throttle Apply - Release Slip Margin (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the closed throttle apply state, converter slip more than this amount above the slip target releases the converter clutch (stock 250 rpm). This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (lower = release sooner on slip in that state) Evidence: ledger:E1306</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D246" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA70" flags="0x0">
    <title>TCC Closed Throttle Apply - Exit Slip (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the closed throttle apply state, converter slip above this value for the exit time returns the clutch to normal applied control (stock 50 rpm). This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1306</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D444" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA71" flags="0x0">
    <title>TCC Closed Throttle Apply - Exit Slip Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long slip must stay above the exit slip before the closed throttle apply state ends (stock 1.0 s). This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1306</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D438" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA72" flags="0x0">
    <title>TCC Closed Throttle Apply - Exit Throttle Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this throttle the closed throttle apply state ends and the clutch returns to normal applied control (stock 1.25 %). This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1306</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D440" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA73" flags="0x0">
    <title>TCC Closed Throttle Apply - Exit Hold Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After leaving the closed throttle apply state the clutch is held in normal applied control for at least this time (stock 0.25 s). This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1306</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D43A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA74" flags="0x0">
    <title>TCC Adapt - Min Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. TCC adapt only learns above this engine torque (stock 0 Nm). Part of TCC adaptive learning: while the converter clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells across 50..210 Nm. Effect: raise = no learning at light load Evidence: ledger:E1307</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CDA6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA75" flags="0x0">
    <title>TCC Adapt - Max Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. TCC adapt only learns below this engine torque (stock 305 Nm). Part of TCC adaptive learning: while the converter clutch is applied and conditions are steady, the PCM learns an offset for the slip controller in five cells across 50..210 Nm. Effect: lower = no learning at high load Evidence: ledger:E1307</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CDA8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA76" flags="0x0">
    <title>TCC Release on Trans Fault - Fluid Below, On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With a transmission fault reaction active (a converter clutch, shift solenoid, pressure control or speed sensor fault), the converter clutch is released while the transmission fluid is below this temperature (stock 150 C). This reaction also runs while the transmission range switch reading is invalid (no valid range for the confirm time). Effect: lower = the clutch may stay applied with a fault at a cooler fluid temperature Evidence: ledger:E1308, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D1D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA77" flags="0x0">
    <title>TCC Release on Trans Fault - Fluid Above, Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this transmission fluid temperature the fault reaction release ends, so the clutch may apply to protect hot fluid (stock 160 C; between the two the last state holds). This reaction also runs while the transmission range switch reading is invalid (no valid range for the confirm time). Effect: lower = hot fluid lets the clutch apply with a fault sooner Evidence: ledger:E1308, ledger:E1476</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D1D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA78" flags="0x0">
    <title>TCC Slip On Target - Alternate Entry Margin</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With the slip target cap turned on, the PCM also moves to on target once slip stays within this margin of the target (stock 50 rpm). Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1309</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D1B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA79" flags="0x0">
    <title>TCC Slip Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Smoothing of the converter slip (engine speed minus transmission input speed) that the converter clutch logic uses: each update the filtered slip moves this fraction of the way to the measured slip (stock 0.25). Effect: raise = filtered slip follows measured slip faster (less smoothing); lower = smoother, slower slip signal Evidence: ledger:E1310</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCB4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xA7A" flags="0x30">
    <title>Shift Set by Drive Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Which upshift set (0, 1 or 2) each drive mode uses for the base shift pressure, desired shift time and the desired shift time altitude tables. Stock: 4WD Low uses set 2, every other mode set 0. Entries 3, 4 and 6 are not used by any mode (dormant). Only 0, 1 and 2 are valid. Effect: moves a drive mode onto another upshift set Evidence: ledger:E0235, ledger:E0237, ledger:E1311</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>drive mode</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="normal" />
      <LABEL index="1" value="cruise" />
      <LABEL index="2" value="4-Lo mode" />
      <LABEL index="3" value="not used" />
      <LABEL index="4" value="not used" />
      <LABEL index="5" value="4WD Low" />
      <LABEL index="6" value="not used" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3BDA4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>set</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA7B" flags="0x30">
    <title>Base Shift Pressure vs Torque - Set 1 (1-2 / 2-3 / 3-4)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base pressure commanded during an upshift, by shift torque (columns) and upshift (rows), in the upshift pressure source used on the stock calibration; this is set 1 (not selected by any mode on the stock calibration). 1 count = 4 kPa = 0.58 psi. Which set each drive mode uses is chosen by Shift Set by Drive Mode. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (shift firmness in set 1 (higher = firmer)) Evidence: ledger:E0235, ledger:E0237, led...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3E3FA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT; data columns: shift torque (Nm))</units>
      <embedinfo type="1" />
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A28F" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>psi</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>147.938454</max>
      <MATH equation="X*0.5801508"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA7C" flags="0x30">
    <title>Desired Shift Time vs Torque - Set 1 (1-2 / 2-3 / 3-4)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target upshift duration the adaptive shift learning steers to, by shift torque, set 1 (not selected by any mode on the stock calibration); 0 = not adapted. Which set each drive mode uses is chosen by Shift Set by Drive Mode. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (adaptive shift duration target in set 1) Evidence: ledger:E0235, ledger:E0237, ledger:E1311</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3E3FA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT; data columns: shift torque (Nm))</units>
      <embedinfo type="1" />
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C07F" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA7D" flags="0x30">
    <title>Desired Shift Time Altitude Weight - Normal (1-2 / 2-3 / 3-4)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How much of the Desired Shift Time Altitude Adder is used, by barometric pressure, set 0 (normal, cruise and 4-Lo shift modes on the stock calibration) (1.0 = all of it). Stock set 0: 1.0 up to 74 kPa, fading to 0 by 98 kPa. Which set each drive mode uses is chosen by Shift Set by Drive Mode. Effect: raise = more of the altitude adder at that barometric pressure Evidence: ledger:E0235, ledger:E0237, ledger:E1311</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="50" />
      <LABEL index="3" value="54" />
      <LABEL index="4" value="58" />
      <LABEL index="5" value="62" />
      <LABEL index="6" value="66" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="74" />
      <LABEL index="9" value="78" />
      <LABEL index="10" value="82" />
      <LABEL index="11" value="86" />
      <LABEL index="12" value="90" />
      <LABEL index="13" value="94" />
      <LABEL index="14" value="98" />
      <LABEL index="15" value="102" />
      <LABEL index="16" value="106" />
      <LABEL index="17" value="110" />
      <LABEL index="18" value="114" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C1A6" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>weight</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>0.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA7E" flags="0x30">
    <title>Desired Shift Time Altitude Adder - Set 1 (1-2 / 2-3 / 3-4)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time added to the desired upshift duration at altitude, by shift torque, set 1 (not selected by any mode on the stock calibration); scaled by the Desired Shift Time Altitude Weight table (1.0 at low barometric pressure, 0 at sea level on the stock calibration). Negative values shorten the target. Stock 0 in every cell. Which set each drive mode uses is chosen by Shift Set by Drive Mode. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (longer (p...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3E3FA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT; data columns: shift torque (Nm))</units>
      <embedinfo type="1" />
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C12F" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>-3.200000</min>
      <max>3.175000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA7F" flags="0x30">
    <title>Desired Shift Time Altitude Weight - Set 1 (1-2 / 2-3 / 3-4)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How much of the Desired Shift Time Altitude Adder is used, by barometric pressure, set 1 (not selected by any mode on the stock calibration) (1.0 = all of it). Stock 0 in every cell. Which set each drive mode uses is chosen by Shift Set by Drive Mode. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (raise = more of the altitude adder at that barometric pressure) Evidence: ledger:E0235, ledger:E0237, ledger:E1311</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="50" />
      <LABEL index="3" value="54" />
      <LABEL index="4" value="58" />
      <LABEL index="5" value="62" />
      <LABEL index="6" value="66" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="74" />
      <LABEL index="9" value="78" />
      <LABEL index="10" value="82" />
      <LABEL index="11" value="86" />
      <LABEL index="12" value="90" />
      <LABEL index="13" value="94" />
      <LABEL index="14" value="98" />
      <LABEL index="15" value="102" />
      <LABEL index="16" value="106" />
      <LABEL index="17" value="110" />
      <LABEL index="18" value="114" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C1DF" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>weight</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>0.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xA80" flags="0x0">
    <title>Idle Spark Correction - Start-up Gain Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle spark correction by rpm error (the idle under and overspeed spark tables): up to this engine run time the correction is multiplied by the coolant gains (Idle Underspeed Spark Gain vs Coolant and Idle Overspeed Spark / Droop Airflow Gain vs Coolant); after it the table value applies unscaled. Stock 0 s: the gains apply only in the first second after start. Effect: raise = the coolant gains shape the idle spark correction for longer after start Evidence: ledger:E1313</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x29744" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA81" flags="0x0">
    <title>STFT Tip-In Reset - Throttle Request Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim tip-in reset: the reset is armed when the throttle area request above the idle area rises from below this to at or above it, at low speed (STFT Tip-In Reset Speed Maximum). Stock 2.0 % above idle. See STFT Tip-In Reset Threshold for what the reset does. Effect: raise = a larger throttle opening is needed to trigger the tip-in reset Evidence: ledger:E1313</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25952" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA82" flags="0x0">
    <title>First-Run Mode - Cranking Fuel Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While first-run mode is active (the first engine running recorded by the PCM, see the First-Run Mode items), the stage 1 cranking fuel multiplier (Cranking FA Mult Stage 1 vs. Cranking Time) is multiplied by this. Stock 2.0: double cranking fuel on a first start. Effect: raise = more cranking fuel during first-run mode Evidence: ledger:E1315</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26CD6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA83" flags="0x0">
    <title>Alternator Field Duty Filter - Idle Airflow Input</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The alternator field (F-terminal) duty reading is filtered into the alternator load input of the idle airflow (the electrical load term of the idle airflow sum). Each update moves the filtered value this fraction of the way to the new reading. Stock 0.20. Effect: raise = the idle airflow follows alternator load changes faster Evidence: ledger:E1315</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x28F52" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA84" flags="0x0">
    <title>Alternator Field Duty Filter - Reported Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The alternator field (F-terminal) duty reading is filtered into the value the scan tool reports as alternator F-terminal duty and the charging system checks use. Each update moves the filtered value this fraction of the way to the new reading. Stock 0.40. Effect: raise = the reported duty and the charging checks follow the reading faster Evidence: ledger:E1315</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20842" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA85" flags="0x0">
    <title>Fuel Level - Sender Table Full Scale</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The Fuel Level vs Sender Voltage table value that counts as a full tank: the fuel level the PCM reports and uses (both fuel level paths) is the table value divided by this. Shown in the table&#x27;s own percent; stock 100 %. Effect: raise = every fuel level reading drops in proportion (less fuel shown for the same sender voltage) Evidence: ledger:E1316</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x2081E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>292.763011</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/223.85"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xA86" flags="0x30">
    <title>Downshift Base Pressure (Normal) - Turbine Speed Part</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turbine speed part of the base pressure for downshifts when an upshift is still available from the current gear, by turbine-side speed (columns) and gear index (rows). The downshift base pressure is the sum of its turbine speed part and its shift torque part; the downshift pressure temperature modifier is added to it. Stock 0 in every cell. Effect: raise = firmer downshift at that turbine speed Evidence: ledger:E1030, ledger:E1170, ledger:E1317</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="1024" />
      <LABEL index="4" value="1536" />
      <LABEL index="5" value="2048" />
      <LABEL index="6" value="2560" />
      <LABEL index="7" value="3072" />
      <LABEL index="8" value="3584" />
      <LABEL index="9" value="4096" />
      <LABEL index="10" value="4608" />
      <LABEL index="11" value="5120" />
      <LABEL index="12" value="5632" />
      <LABEL index="13" value="6144" />
      <LABEL index="14" value="6656" />
      <LABEL index="15" value="7168" />
      <LABEL index="16" value="7680" />
      <LABEL index="17" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A0FE" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA87" flags="0x30">
    <title>Downshift Base Pressure (Normal) - Torque Part</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift torque part of the base pressure for downshifts when an upshift is still available from the current gear, by shift torque (columns) and gear index (rows). The downshift base pressure is the sum of its turbine speed part and its shift torque part; the downshift pressure temperature modifier is added to it. 1 count = 4 kPa. Effect: raise = firmer downshift at that shift torque Evidence: ledger:E1030, ledger:E1170, ledger:E1317</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <LABEL index="9" value="140" />
      <LABEL index="10" value="160" />
      <LABEL index="11" value="180" />
      <LABEL index="12" value="200" />
      <LABEL index="13" value="220" />
      <LABEL index="14" value="240" />
      <LABEL index="15" value="260" />
      <LABEL index="16" value="280" />
      <LABEL index="17" value="300" />
      <LABEL index="18" value="320" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A301" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>1020.000000</max>
      <MATH equation="X*4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA88" flags="0x30">
    <title>Downshift Base Pressure (Top Gear, High Torque) - Turbine Speed Part</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turbine speed part of the base pressure for downshifts from top gear with the torque state high (power on), by turbine-side speed (columns) and gear index (rows). The downshift base pressure is the sum of its turbine speed part and its shift torque part; the downshift pressure temperature modifier is added to it. &#x27;Top gear&#x27; means no upshift is available from the current gear: the highest gear the selected range allows, or a gear held by the cruise rule. Stock 0 in every cell. Effect: raise = firmer downshift at that turb...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="1024" />
      <LABEL index="4" value="1536" />
      <LABEL index="5" value="2048" />
      <LABEL index="6" value="2560" />
      <LABEL index="7" value="3072" />
      <LABEL index="8" value="3584" />
      <LABEL index="9" value="4096" />
      <LABEL index="10" value="4608" />
      <LABEL index="11" value="5120" />
      <LABEL index="12" value="5632" />
      <LABEL index="13" value="6144" />
      <LABEL index="14" value="6656" />
      <LABEL index="15" value="7168" />
      <LABEL index="16" value="7680" />
      <LABEL index="17" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A1DE" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA89" flags="0x30">
    <title>Downshift Base Pressure (Top Gear, High Torque) - Torque Part</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift torque part of the base pressure for downshifts from top gear with the torque state high (power on), by shift torque (columns) and gear index (rows). The downshift base pressure is the sum of its turbine speed part and its shift torque part; the downshift pressure temperature modifier is added to it. &#x27;Top gear&#x27; means no upshift is available from the current gear: the highest gear the selected range allows, or a gear held by the cruise rule. 1 count = 4 kPa. Effect: raise = firmer downshift at that shift torque Evidenc...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <LABEL index="9" value="140" />
      <LABEL index="10" value="160" />
      <LABEL index="11" value="180" />
      <LABEL index="12" value="200" />
      <LABEL index="13" value="220" />
      <LABEL index="14" value="240" />
      <LABEL index="15" value="260" />
      <LABEL index="16" value="280" />
      <LABEL index="17" value="300" />
      <LABEL index="18" value="320" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A45A" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>1020.000000</max>
      <MATH equation="X*4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA8A" flags="0x30">
    <title>Downshift Base Pressure (Top Gear, Low Torque) - Turbine Speed Part</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turbine speed part of the base pressure for downshifts from top gear with the torque state low, by turbine-side speed (columns) and gear index (rows). The downshift base pressure is the sum of its turbine speed part and its shift torque part; the downshift pressure temperature modifier is added to it. &#x27;Top gear&#x27; means no upshift is available from the current gear: the highest gear the selected range allows, or a gear held by the cruise rule. Effect: raise = firmer downshift at that turbine speed Evidence: ledger:E1030, l...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="1024" />
      <LABEL index="4" value="1536" />
      <LABEL index="5" value="2048" />
      <LABEL index="6" value="2560" />
      <LABEL index="7" value="3072" />
      <LABEL index="8" value="3584" />
      <LABEL index="9" value="4096" />
      <LABEL index="10" value="4608" />
      <LABEL index="11" value="5120" />
      <LABEL index="12" value="5632" />
      <LABEL index="13" value="6144" />
      <LABEL index="14" value="6656" />
      <LABEL index="15" value="7168" />
      <LABEL index="16" value="7680" />
      <LABEL index="17" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A16E" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA8B" flags="0x30">
    <title>Downshift Base Pressure (Top Gear, Low Torque) - Torque Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift torque breakpoints of the Downshift Base Pressure (Top Gear, Low Torque) torque part (stock 0 to 160 Nm). Axis data: keep ascending. Effect: moves the torque points of that table Evidence: ledger:E1030, ledger:E1170, ledger:E1317</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A0A8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA8C" flags="0x30">
    <title>Upshift Base Pressure (Top Gear, Low Torque) - Torque Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift torque breakpoints of the Upshift Base Pressure (Top Gear, Low Torque) table (stock 0 to 640 Nm). Axis data: keep ascending. Effect: moves the torque points of that table Evidence: ledger:E1030, ledger:E1170, ledger:E1317</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A0CC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA8D" flags="0x30">
    <title>Shift Adapt - Allowed Shift Delay vs Shift Time</title>
    <description>Change in small steps and log. Each row is [COUNT][TYPE][points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Longest shift delay accepted without a delay correction, by the measured shift time (columns) for each upshift (rows). When the shift delay is longer, the learned shift pressure gets the shift delay step instead of the usual shift time step. Stock 0.8 s for 1-2, 1.5 s for 2-3, 0 for 3-4 (3-4 is not adapted). Shift delay is the time from the shift command to the start of the ratio change; shift time is the time the ratio change itself takes. Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0.0" />
      <LABEL index="3" value="0.1" />
      <LABEL index="4" value="0.2" />
      <LABEL index="5" value="0.3" />
      <LABEL index="6" value="0.4" />
      <LABEL index="7" value="0.5" />
      <LABEL index="8" value="0.6" />
      <LABEL index="9" value="0.7" />
      <LABEL index="10" value="0.8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C27C" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA8E" flags="0x30">
    <title>Shift Adapt - Pressure Step vs Excess Shift Delay</title>
    <description>Change in small steps and log. Each row is [COUNT][TYPE][points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Step added to the learned shift pressure when the shift delay was longer than allowed, by how much longer (columns), for each upshift (rows); multiplied by the delay step gain. Stock 10 to 40 kPa for 1-2 and 2-3, 0 for 3-4. Shift delay is the time from the shift command to the start of the ratio change; shift time is the time the ratio change itself takes. Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Effect: raise = faster correction of long shift delays Evidence: ledger:...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0.0" />
      <LABEL index="3" value="0.1" />
      <LABEL index="4" value="0.2" />
      <LABEL index="5" value="0.3" />
      <LABEL index="6" value="0.4" />
      <LABEL index="7" value="0.5" />
      <LABEL index="8" value="0.6" />
      <LABEL index="9" value="0.7" />
      <LABEL index="10" value="0.8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C4FC" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>510.000000</max>
      <MATH equation="X*2"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xA8F" flags="0x0">
    <title>Shift Adapt - Delay Correction Min Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The shift delay correction is only used above this transmission fluid temperature (stock 60 C). Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Effect: raise = no delay correction until the fluid is warmer Evidence: ledger:E0806, ledger:E1029, ledger:E1318</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C524" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA90" flags="0x0">
    <title>Shift Adapt - Delay Correction Min Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The shift delay step replaces the usual shift time step only when it is at least this large (stock 0 kPa: whenever the delay was too long and the temperature and throttle conditions are met). Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Effect: raise = the delay correction takes over only for larger steps Evidence: ledger:E0806, ledger:E1029, ledger:E1318</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C388" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xA91" flags="0x30">
    <title>Shift Adapt - Min Time in Range by Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A shift is not used for learning unless the selector has been in the same range at least this long (stock 3.0 s). Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Effect: raise = learning waits longer after a range change Evidence: ledger:E0806, ledger:E1029, ledger:E1318</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C252" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA92" flags="0x30">
    <title>Shift Adapt - Min Time in Gear Before the Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A shift is not used for learning unless the previous gear was held at least this long before the shift (stock 2.0 s). Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Effect: raise = learning skips shifts that follow quickly after another Evidence: ledger:E0806, ledger:E1029, ledger:E1318</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C258" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA93" flags="0x30">
    <title>Shift Adapt - Fixed Step for Much Slower Shifts</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fixed step used instead of the shift time step when the shift time error is below the Fixed Step Time Error Limit (stock 0; the stock limit is never reached). Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (fixed learning step) Evidence: ledger:E0806, ledger:E1029, ledger:E1318</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C382" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xA94" flags="0x0">
    <title>Trans Range Switch - Invalid Reading Confirm Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the range switch inputs change to an invalid combination, the new reading must last this long before the transmission takes it as the selector position (an invalid range). Valid positions use the range switch debounce time table instead. Stock 0.025 s. Effect: raise = a brief invalid range switch reading is ignored for longer Evidence: ledger:E1319</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E800" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA95" flags="0x0">
    <title>P1818 Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1818 (pressure switch shows a drive range with the reverse ratio): time with the ratio inside a forward gear window that passes the check. Stock 0.05 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1322</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F882" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA96" flags="0x0">
    <title>P1887 Fail - Event Count (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1887 (converter clutch release switch check): fail events (each one fail event time with the switch reading released while the clutch is applied) needed to set the code. Stock 255. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1324</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F676" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xA97" flags="0x30">
    <title>Cruise Control - Throttle Area vs Cruise Demand</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle opening above the idle throttle area that the cruise control asks for, by the controller&#x27;s internal demand (a lower demand means more throttle). Multiplied by a barometric correction and ramped, it is used in place of the accelerator pedal while cruise holds speed. Stock 100 % at the lowest demand falling to 0 from the middle of the range. Effect: raise = more throttle for the same cruise demand Evidence: ledger:E0943, ledger:E1326</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>cruise demand (internal counts)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-5760" />
      <LABEL index="1" value="-5272" />
      <LABEL index="2" value="-4784" />
      <LABEL index="3" value="-4296" />
      <LABEL index="4" value="-3808" />
      <LABEL index="5" value="-3320" />
      <LABEL index="6" value="-2832" />
      <LABEL index="7" value="-2344" />
      <LABEL index="8" value="-1856" />
      <LABEL index="9" value="-1368" />
      <LABEL index="10" value="-880" />
      <LABEL index="11" value="-392" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="584" />
      <LABEL index="14" value="1072" />
      <LABEL index="15" value="1560" />
      <LABEL index="16" value="2048" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22328" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle area</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA98" flags="0x30">
    <title>Fuel Level 2 - Level vs Sender Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converts the filtered fuel level sender voltage (0 to 5 V in 0.156 V steps) to the second fuel level. Stock reads full (101 %) up to about 0.8 V and empty from about 2.7 V, close to the first fuel level table. Second fuel level, used by the starter low-voltage hold and sent in a data message. Values are fuel level as read from the sender curve, before the offset. Effect: change only to match a different fuel sender Evidence: ledger:E1036, ledger:E1331</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>V (fuel level sender)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.156" />
      <LABEL index="2" value="0.312" />
      <LABEL index="3" value="0.469" />
      <LABEL index="4" value="0.625" />
      <LABEL index="5" value="0.781" />
      <LABEL index="6" value="0.938" />
      <LABEL index="7" value="1.094" />
      <LABEL index="8" value="1.25" />
      <LABEL index="9" value="1.406" />
      <LABEL index="10" value="1.562" />
      <LABEL index="11" value="1.719" />
      <LABEL index="12" value="1.875" />
      <LABEL index="13" value="2.031" />
      <LABEL index="14" value="2.188" />
      <LABEL index="15" value="2.344" />
      <LABEL index="16" value="2.5" />
      <LABEL index="17" value="2.656" />
      <LABEL index="18" value="2.812" />
      <LABEL index="19" value="2.969" />
      <LABEL index="20" value="3.125" />
      <LABEL index="21" value="3.281" />
      <LABEL index="22" value="3.438" />
      <LABEL index="23" value="3.594" />
      <LABEL index="24" value="3.75" />
      <LABEL index="25" value="3.906" />
      <LABEL index="26" value="4.062" />
      <LABEL index="27" value="4.219" />
      <LABEL index="28" value="4.375" />
      <LABEL index="29" value="4.531" />
      <LABEL index="30" value="4.688" />
      <LABEL index="31" value="4.844" />
      <LABEL index="32" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x207DC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% fuel level</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>292.763011</max>
      <MATH equation="X/223.85"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xA99" flags="0x0">
    <title>Fuel Level 2 - Level Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Subtracted from the sender curve&#x27;s level before it is filtered into the second fuel level (stock 1.0 %); the first fuel level calculation subtracts it as well. Second fuel level, used by the starter low-voltage hold and sent in a data message. Values are fuel level as read from the sender curve, before the offset. Effect: raise = the fuel level reads lower by that much Evidence: ledger:E1036, ledger:E1331</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x207CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% fuel level</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>292.763011</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/223.85"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA9A" flags="0x0">
    <title>Fuel Level 2 - Low Fuel Timer Start Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this level the low fuel timer starts; once it runs for the low fuel time the fast filter is used (stock 3.4 %). Second fuel level, used by the starter low-voltage hold and sent in a data message. Values are fuel level as read from the sender curve, before the offset. Effect: raise = low fuel handling starts at a higher level Evidence: ledger:E1036, ledger:E1331</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x207D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% fuel level</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>292.763011</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/223.85"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA9B" flags="0x0">
    <title>Fuel Level 2 - Low Fuel Clear Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or above this level the low fuel timer is cleared, and above it the low fuel state ends and the normal slow filter returns (stock 9.7 %). Second fuel level, used by the starter low-voltage hold and sent in a data message. Values are fuel level as read from the sender curve, before the offset. Effect: raise = the level must recover further before low fuel handling ends Evidence: ledger:E1036, ledger:E1331</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x207D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% fuel level</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>292.763011</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/223.85"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA9C" flags="0x0">
    <title>Cold Weather Shift Offset - Cold Start Fluid Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During the first 30 seconds of engine run, when intake air is too warm for either cold air blend, a transmission fluid temperature at start-up below this still selects the cold air pair of fluid temperatures for the cold weather offset. Stock -255 C: never. The cold weather offset adds an offset to the shift points and to the converter clutch apply and release points, weighted from full to none by transmission fluid temperature. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1332</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DD00" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA9D" flags="0x0">
    <title>Force Motor Current Sense Trim (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Offset in A/D counts added to the force motor (pressure control solenoid) current reading before it becomes the measured current used by the current loop. It applies only when the reading is at or above 573 counts (about 2.8 V) and the trim is between -49 and 49; zero means no trim. Stock 0. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (positive = the measured current reads higher) Evidence: ledger:E1332</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F47C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>counts</units>
    <decimalpl>0</decimalpl>
    <min>-32768.000000</min>
    <max>32767.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA9E" flags="0x0">
    <title>Knock Retard - Park / Neutral Start-Up Hold-Off Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. For this long after the engine starts, while the transmission is in Park or Neutral, the knock retard update for each cylinder is skipped and the knock-active flag is cleared, so no new knock retard is added. In gear, or after this time, knock retard works normally. Stock 10 s. Effect: raise = knock retard stays off longer after a start in Park or Neutral Evidence: ledger:E1333</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AF16" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xA9F" flags="0x0">
    <title>Crank Signal Loss - Reference Period Speed Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When no crank reference event (one every 12 teeth) arrives for this long, the engine speed measured from the reference period is marked invalid and its period set to the maximum, so the PCM takes engine speed from the tooth period measurement instead. Companion of Crank and Cam Signal Loss Watchdog B. Stock 0.4 s. Effect: raise = a lost crank reference signal is noticed later Evidence: ledger:E1333</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x23A42" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xAA0" flags="0x30">
    <title>Ambient Air Temp Estimate - Flush Requirement vs Soak Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Seconds of qualifying driving (above the airflow and speed gates, at flush weight 1.0) needed before the ambient air temperature estimate may rise again, by engine-off soak time. Stock 60 s after a short stop, up to 80 s after about 40 minutes, down to 20 s near 7 hours. If the previous drive ended before the estimate was released, the largest value of this curve is used. The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it d...</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3456A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>33</indexcount>
      <units>s</units>
      <embedinfo type="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34522" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>204.796875</max>
      <MATH equation="X/320"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xAA1" flags="0x0">
    <title>Ambient Air Temp Estimate - Soak Time for Immediate Reset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After an engine-off soak at least this long (stock 25200 s = 7 h) the ambient estimate is taken straight from the intake air temperature at start-up and no flush is required. The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it down, and until it reaches zero the estimate can only fall toward the intake air temperature. Effect: lower = the intake reading is trusted at start-up after a shorter soak Evidence: ledger:E0385, ledg...</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x34564" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAA2" flags="0x0">
    <title>Ambient Air Temp Estimate - Soak Time Limit for Stored Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a soak up to this long (stock 7200 s = 2 h) the ambient estimate starts from the value stored at the end of the last drive when that is lower than the intake air temperature; after a longer soak it starts from the intake air temperature. The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it down, and until it reaches zero the estimate can only fall toward the intake air temperature. Effect: raise = the stored ambient val...</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x34518" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAA3" flags="0x0">
    <title>ETC Torque Control - Window, Airmass Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest cylinder airmass (stock 1.0 g/cyl). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x214AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/cyl</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8.191875</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAA4" flags="0x0">
    <title>ETC Torque Control - Window, Airmass Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest cylinder airmass (stock 0.02 g/cyl). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x214B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/cyl</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8.191875</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAA5" flags="0x0">
    <title>ETC Torque Control - Window, Engine Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest filtered engine speed (stock 7000 rpm). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x214B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAA6" flags="0x0">
    <title>ETC Torque Control - Window, Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest filtered engine speed (stock 400 rpm). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x214B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAA7" flags="0x0">
    <title>ETC Torque Control - Window, Coolant Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest coolant temperature (stock 30 C). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x214BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAA8" flags="0x0">
    <title>ETC Torque Control - Window, Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine run time since start needed (stock 0 s). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x214BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAA9" flags="0x0">
    <title>ETC Torque Control - Window, Vehicle Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest vehicle speed (stock 512 km/h: no limit). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x214BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAAA" flags="0x0">
    <title>ETC Torque Control - Window, Vehicle Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest vehicle speed (stock 1 km/h). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x214C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xAAB" flags="0x30">
    <title>TCC Release with A/C On - Speed by Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With the A/C compressor running (and the transmission not in hot mode), below this vehicle speed in each gear the converter clutch is released. The feature is switched off on the stock calibration (stock 512 km/h in 1st, 0 in 2nd to 4th), so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1341</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D23C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAAC" flags="0x30">
    <title>TCC Release with A/C On While Applied - Speed by Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With the converter clutch applied and the A/C compressor running (transmission not in hot mode), below this vehicle speed in each gear the clutch is ramped off. The feature is switched off on the stock calibration (stock 512 km/h in 1st, 0 in 2nd to 4th), so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1341</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D48E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xAAD" flags="0x0">
    <title>TCC Release Ramp - Slip Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During the converter clutch release ramp (pressure ramping down, solenoid still on), slip at or below this value counts as still coupled and slip above it as let go; each side has its own time limit (stock 400 rpm). Effect: raise = more slip still counts as coupled during the release ramp Evidence: ledger:E1342</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D48A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAAE" flags="0x0">
    <title>TCC Release Ramp - Time Limit, Low Slip</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. If slip is still at or below the release ramp slip threshold after this long in the release ramp, the ramp ends and the clutch pressure drops to zero (stock 2.0 s). The ramp also ends as soon as the pressure reaches zero. Effect: lower = a release that is not letting go is cut short sooner Evidence: ledger:E1342</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D462" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAAF" flags="0x0">
    <title>TCC Release Ramp - Time Limit, High Slip</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once slip has been above the release ramp slip threshold for this long in total during the ramp, the ramp ends and the clutch pressure drops to zero (stock 3.0 s). Effect: lower = the release ramp ends sooner once the clutch has let go Evidence: ledger:E1342</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D468" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAB0" flags="0x0">
    <title>TCC Release - Zero Pressure Time Before Solenoid Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After the release ramp, the clutch pressure is held at zero this long with the converter clutch solenoid still on, then the solenoid is switched off (stock 0.1 s). Effect: raise = the solenoid stays on longer after the pressure is dropped Evidence: ledger:E1342</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D466" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAB1" flags="0x0">
    <title>TCC Release - Solenoid Off Time Before Released</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After the converter clutch solenoid is switched off, the release sequence completes after this time and the clutch counts as released (stock 0.1 s). Effect: raise = the release sequence takes longer to complete Evidence: ledger:E1342</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D284" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAB2" flags="0x0">
    <title>TCC Closed Throttle Apply - Speed On Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this vehicle speed the closed throttle apply state of the converter clutch is allowed (stock 28 km/h). Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1343</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D49E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAB3" flags="0x0">
    <title>TCC Closed Throttle Apply - Speed Off Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this vehicle speed the closed throttle apply state ends (stock 23.5 km/h; between the two the last state holds). Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1343</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D49C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xAB4" flags="0x30">
    <title>TCC Pressure at Full Command - Line Pressure Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Line pressure (0 to 640 kPa): breakpoints of TCC Pressure at Full Command vs Line Pressure. Axis data: keep ascending. Effect: moves the table points it indexes Evidence: ledger:E0354, ledger:E1344</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D4FA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAB5" flags="0x30">
    <title>TCC Pressure Ceiling vs Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit on the converter clutch pressure command at each engine speed (stock 827 kPa everywhere). While the clutch is released the pressure command is preset to this value above about 12 km/h. Effect: lower = caps the clutch apply pressure (softer, more slip under load) at that engine speed Evidence: ledger:E1345</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D40E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAB6" flags="0x30">
    <title>TCC Slip Control - Slip Error Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Slip error (slip minus slip target, -80 to 350 rpm): breakpoints of TCC Slip Control step size by slip error. Axis data: keep ascending. Effect: moves the table points it indexes Evidence: ledger:E0351, ledger:E1346</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D12C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>-4096.000000</min>
      <max>4095.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAB7" flags="0x30">
    <title>TCC Adapt - Learning Confidence Reset Values (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Values a special reset mode would load into the five learning confidence counters (cells at 50, 90, 130, 170 and 210 Nm; stock 0). That mode is not available on this operating system, and a normal learning reset clears the counters to 0, so this has no effect. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (converter clutch learning, no effect) Evidence: ledger:E1347, ledger:E1432</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3CE82" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>5</indexcount>
      <units>Nm</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CDCA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAB8" flags="0x30">
    <title>TCC Adapt - Learning Bank Reset Values (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Values a special reset mode would load into the five cells of the converter clutch learning bank (cells at 50, 90, 130, 170 and 210 Nm; stock 0). That mode is not available on this operating system, and a normal learning reset clears the cells to 0, so this has no effect. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (converter clutch learning, no effect) Evidence: ledger:E1347</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3CE82" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>5</indexcount>
      <units>Nm</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CDD6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAB9" flags="0x30">
    <title>Shift Adapt - Min Throttle by Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A shift is not used for learning when the throttle is below this (stock 25 % for 1-2 and 2-3, 0 for 3-4). Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Effect: lower = learning also uses lighter throttle shifts Evidence: ledger:E0319, ledger:E1348</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C5DE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xABA" flags="0x30">
    <title>Shift Adapt - Max Throttle by Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A shift is not used for learning when the throttle is above this (stock 100 % for 1-2 and 2-3, 0 for 3-4, which with its 0 minimum keeps 3-4 from learning). Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Effect: lower = learning skips heavy throttle shifts Evidence: ledger:E0319, ledger:E1348</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C5D8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xABB" flags="0x30">
    <title>Shift Adapt - Max Speed Change During the Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A shift is not used for learning when vehicle speed changed by more than this since the shift started (stock 20 km/h 1-2, 16 km/h 2-3, 0 for 3-4). Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Effect: raise = learning also uses shifts with larger speed changes Evidence: ledger:E0319, ledger:E1348</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C29E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xABC" flags="0x30">
    <title>Shift Adapt - Learning Step Share of Neighbour Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The learned shift pressure is stored in cells over shift torque. A learning step goes to the cell of the shift&#x27;s torque and its neighbours by these shares (stock 0 / 0.5 / 1.0 / 0.5 / 0 for two cells below, one below, the cell itself, one above, two above). Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Effect: raise the side shares = each shift also adapts the neighbouring torque cells more Evidence: ledger:E0319, ledger:E1348</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>cell offset</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-2" />
      <LABEL index="1" value="-1" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="+1" />
      <LABEL index="4" value="+2" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C578" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>weight</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xABD" flags="0x0">
    <title>Shift Adapt - Max Base Plus Learned Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A learned cell is limited so that the base shift pressure plus the learned value does not exceed this (stock 622 kPa). Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Effect: lower = less room for the learned pressure at high base pressure Evidence: ledger:E0319, ledger:E1348</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C51E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xABE" flags="0x30">
    <title>Upshift Inhibit - Speed Ratio Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter speed ratio (turbine speed / engine speed) breakpoints of the torque-based upshift inhibit predictor&#x27;s first curve (stock 0 to 1.0 in 1/16 steps). Axis data: keep ascending. Effect: moves the speed ratio points of that curve Evidence: ledger:E0345, ledger:E1349</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39136" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>speed ratio</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xABF" flags="0x30">
    <title>Cold Weather Shift Offset - Upshift Speed vs Throttle</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the upshift speed by throttle (columns) and upshift (rows), when the high pedal demand is off. Part of the cold weather offset, which shifts the shift points while the transmission fluid is cold, weighted from full to none by the Cold Weather Shift Offset temperatures. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (positive = later upshifts when cold) Evidence: ledger:E0727, ledger:E1027, ledger:E1350</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>upshift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38FD8" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAC0" flags="0x30">
    <title>Cold Weather Shift Offset - Downshift Speed vs Throttle</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the downshift speed by throttle (columns) and downshift (rows), when the high pedal demand is off. Part of the cold weather offset, which shifts the shift points while the transmission fluid is cold, weighted from full to none by the Cold Weather Shift Offset temperatures. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (positive = earlier downshifts when cold) Evidence: ledger:E0727, ledger:E1027, ledger:E1350</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>downshift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2-1" />
      <LABEL index="1" value="3-2" />
      <LABEL index="2" value="4-3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39011" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAC1" flags="0x30">
    <title>Cold Weather Shift Offset - Upshift Speed, High Pedal</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the upshift speed when the high pedal demand is on (stock -9.3 / -18.0 mph for 1-2 / 2-3, 0 for 3-4). Part of the cold weather offset, which shifts the shift points while the transmission fluid is cold, weighted from full to none by the Cold Weather Shift Offset temperatures. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0727, ledger:E1027, ledger:E1350</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>upshift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38FCC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>-159.071025</min>
      <max>159.066171</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAC2" flags="0x30">
    <title>Cold Weather Shift Offset - Downshift Speed, High Pedal</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the downshift speed when the high pedal demand is on (stock -9.3 / -18.0 mph for 2-1 / 3-2, 0 for 4-3). Part of the cold weather offset, which shifts the shift points while the transmission fluid is cold, weighted from full to none by the Cold Weather Shift Offset temperatures. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0727, ledger:E1027, ledger:E1350</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>downshift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2-1" />
      <LABEL index="1" value="3-2" />
      <LABEL index="2" value="4-3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38FD2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>-159.071025</min>
      <max>159.066171</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAC3" flags="0x30">
    <title>Cold Weather Shift Offset - WOT Shift RPM (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the wide open throttle shift rpm by current gear (stock -1575 rpm in 1st and 2nd, 0 in 3rd). Part of the cold weather offset, which shifts the shift points while the transmission fluid is cold, weighted from full to none by the Cold Weather Shift Offset temperatures. Stock those temperatures are -255 C, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (negative = earlier WOT shifts when cold) Evidence: ledger:E0727, ledger:E1027, ledger:E1350</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3904A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>-4096.000000</min>
      <max>4095.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAC4" flags="0x30">
    <title>Top Gear Line Pressure - Torque Limit vs Speed</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque above which line pressure counts as heavy load, by speed (columns) and current gear (rows). In top gear with light load the line pressure uses the Top Gear Line Pressure Offset and the line pressure torque gain for that mode. Stock 0 to 46.5 Nm (1st row) and 0 to 40 Nm. Line pressure has four modes: light or heavy engine torque (Top Gear Line Pressure - Torque Limit), each in or out of top gear (no upshift available). Effect: raise = the light load line pressure mode is used up to more torque Evidence: ledger:E0247,...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="128" />
      <LABEL index="4" value="192" />
      <LABEL index="5" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C85C" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xAC5" flags="0x0">
    <title>Top Gear Line Pressure - Torque Limit Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Band around the Top Gear Line Pressure Torque Limit: heavy above limit plus this, light below limit minus this (stock 0). Line pressure has four modes: light or heavy engine torque (Top Gear Line Pressure - Torque Limit), each in or out of top gear (no upshift available). Effect: raise = fewer mode changes near the limit Evidence: ledger:E0247, ledger:E1030, ledger:E1351</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C85A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xAC6" flags="0x30">
    <title>Top Gear Line Pressure - Offset vs Speed</title>
    <description>Change in small steps and log. Each row is [COUNT][TYPE][points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In top gear with light engine torque, the line pressure offset (used instead of Line Pressure Base Offset), by speed (columns) and current gear (rows); in top gear with heavy torque it is the minimum line pressure. Stock 0, so top gear light load line pressure is the torque term alone, at least the base offset. Line pressure has four modes: light or heavy engine torque (Top Gear Line Pressure - Torque Limit), each in or out of top gear (no upshift available). Effect: raise = more line pressure in top gear at that speed Evidence: ledger:E02...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="16" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="48" />
      <LABEL index="6" value="64" />
      <LABEL index="7" value="80" />
      <LABEL index="8" value="96" />
      <LABEL index="9" value="112" />
      <LABEL index="10" value="128" />
      <LABEL index="11" value="144" />
      <LABEL index="12" value="160" />
      <LABEL index="13" value="176" />
      <LABEL index="14" value="192" />
      <LABEL index="15" value="208" />
      <LABEL index="16" value="224" />
      <LABEL index="17" value="240" />
      <LABEL index="18" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C650" mmedelementsizebits="8" mmedrowcount="4" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>1020.000000</max>
      <MATH equation="X*4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xAC7" flags="0x0">
    <title>Top Gear Line Pressure - Use Alternate Base Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = in top gear use Line Pressure Base Offset (Alternate) instead of the Top Gear Line Pressure Offset table. Stock 0. Line pressure has four modes: light or heavy engine torque (Top Gear Line Pressure - Torque Limit), each in or out of top gear (no upshift available). Effect: 1 = top gear line pressure offset from the alternate array Evidence: ledger:E0247, ledger:E1030, ledger:E1351</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C894" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0/1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xAC8" flags="0x30">
    <title>Line Pressure - Offset with Converter Clutch On vs Turbine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to line pressure while the converter clutch is applied, by turbine speed. Stock 0. Effect: raise = more line pressure with the clutch applied Evidence: ledger:E0247, ledger:E1030, ledger:E1351</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (turbine)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C6B7" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>-512.000000</min>
      <max>508.000000</max>
      <MATH equation="X*4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAC9" flags="0x30">
    <title>Line Pressure - Offset vs Trans Temp by Gear</title>
    <description>Change in small steps and log. Each row is [COUNT][TYPE][points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to line pressure by transmission fluid temperature (columns, at the Line Pressure Offset Temp Breakpoints) and gear and converter clutch state (rows). Stock 0. Effect: raise = more line pressure at that temperature Evidence: ledger:E0247, ledger:E1030, ledger:E1351</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="2" />
      <LABEL index="4" value="3" />
      <LABEL index="5" value="4" />
      <LABEL index="6" value="5" />
      <LABEL index="7" value="6" />
      <LABEL index="8" value="7" />
      <LABEL index="9" value="8" />
      <LABEL index="10" value="9" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>gear / converter clutch</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="1st, TCC on" />
      <LABEL index="2" value="2nd" />
      <LABEL index="3" value="2nd, TCC on" />
      <LABEL index="4" value="3rd" />
      <LABEL index="5" value="3rd, TCC on" />
      <LABEL index="6" value="4th" />
      <LABEL index="7" value="4th, TCC on" />
      <LABEL index="8" value="Reverse" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C710" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>-1024.000000</min>
      <max>1016.000000</max>
      <MATH equation="X*8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xACA" flags="0x30">
    <title>Line Pressure - Offset Temp Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fluid temperature points of Line Pressure Offset vs Trans Temp (stock all 0). Axis data: keep ascending. Effect: moves the temperature points of that table Evidence: ledger:E0247, ledger:E1030, ledger:E1351</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C776" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xACB" flags="0x0">
    <title>Line Pressure - Leave Out Learned Value in 4WD Low with TCC On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = in 4WD Low with the converter clutch applied, the learned line pressure value is not added. Stock 1. Effect: 0 = 4WD Low also gets the learned line pressure Evidence: ledger:E0247, ledger:E1030, ledger:E1351</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C832" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0/1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xACC" flags="0x0">
    <title>Line Pressure Override - Below Throttle (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this throttle (and below the speed limit) line pressure is taken from the Line Pressure Override tables. Stock the throttle and speed limits are 0, so the override never runs: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0247, ledger:E1030, ledger:E1351</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C788" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xACD" flags="0x0">
    <title>Line Pressure Override - Below Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this speed (and below the throttle limit) line pressure is taken from the Line Pressure Override tables. Stock the throttle and speed limits are 0, so the override never runs: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0247, ledger:E1030, ledger:E1351</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C78A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xACE" flags="0x30">
    <title>Line Pressure Override - Pressure vs Trans Temp (dormant)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Line pressure used at low throttle and low speed, by fluid temperature (columns) and state (rows: range codes 5 and 7, reverse, other ranges, top gear). Stock 0. Stock the throttle and speed limits are 0, so the override never runs: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0247, ledger:E1030, ledger:E1351</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-7" />
      <LABEL index="3" value="14" />
      <LABEL index="4" value="35" />
      <LABEL index="5" value="56" />
      <LABEL index="6" value="77" />
      <LABEL index="7" value="98" />
      <LABEL index="8" value="119" />
      <LABEL index="9" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="range code 5 / 7" />
      <LABEL index="1" value="reverse" />
      <LABEL index="2" value="other" />
      <LABEL index="3" value="top gear" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C790" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xACF" flags="0x30">
    <title>TCC Duty Cycle Minimum - Line Pressure Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Line pressure points (rows) of the converter clutch duty cycle minimum table. Stock 0 to 640 kPa in 80 kPa steps. The table is spread over these points, so moving them re-spaces it; keep the point count and keep the points rising. Effect: moves the line pressure axis of the duty cycle minimum table: edit with care Evidence: ledger:E1352</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DBD2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAD0" flags="0x30">
    <title>TCC Duty Cycle Maximum - Line Pressure Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Line pressure points (rows) of the converter clutch duty cycle maximum table. Stock 0 to 640 kPa in 80 kPa steps. The table is spread over these points, so moving them re-spaces it; keep the point count and keep the points rising. Effect: moves the line pressure axis of the duty cycle maximum table: edit with care Evidence: ledger:E1352</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DBE6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAD1" flags="0x30">
    <title>Cruise Control - Accelerate Rate vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control. How fast the cruise target speed rises while cruise is accelerating from the resume / accelerate switch, by vehicle speed (applied every 100 ms up to the highest cruise speed). Stock 4.1 km/h per s at 38 km/h falling to 2.3 km/h per s from about 127 km/h. Effect: raise = cruise accelerates faster at that speed Evidence: ledger:E1353</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.9" />
      <LABEL index="2" value="55.8" />
      <LABEL index="3" value="64.6" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.4" />
      <LABEL index="6" value="91.2" />
      <LABEL index="7" value="100.1" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.9" />
      <LABEL index="10" value="126.8" />
      <LABEL index="11" value="135.6" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.4" />
      <LABEL index="14" value="162.2" />
      <LABEL index="15" value="171.1" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21FBC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per s</units>
      <decimalpl>2</decimalpl>
      <min>-2560.000000</min>
      <max>2559.921875</max>
      <MATH equation="X/12.8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAD2" flags="0x30">
    <title>Cruise Control - Resume Rate vs Distance Below Set Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control. How fast the cruise target speed rises while cruise brings the vehicle back up to the set speed, by how far below the set speed it is (applied every 100 ms; at the set speed cruise goes back to holding). Stock 3.5 km/h per s from 70 to about 44 km/h below, easing to 0.6 km/h per s close to the set speed. Effect: raise = cruise returns to the set speed faster from that far below Evidence: ledger:E0488, ledger:E1353</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (speed minus set speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-70" />
      <LABEL index="1" value="-65.6" />
      <LABEL index="2" value="-61.2" />
      <LABEL index="3" value="-56.9" />
      <LABEL index="4" value="-52.5" />
      <LABEL index="5" value="-48.1" />
      <LABEL index="6" value="-43.8" />
      <LABEL index="7" value="-39.4" />
      <LABEL index="8" value="-35" />
      <LABEL index="9" value="-30.6" />
      <LABEL index="10" value="-26.2" />
      <LABEL index="11" value="-21.9" />
      <LABEL index="12" value="-17.5" />
      <LABEL index="13" value="-13.1" />
      <LABEL index="14" value="-8.8" />
      <LABEL index="15" value="-4.4" />
      <LABEL index="16" value="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21FE0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per s</units>
      <decimalpl>2</decimalpl>
      <min>-2560.000000</min>
      <max>2559.921875</max>
      <MATH equation="X/12.8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAD3" flags="0x30">
    <title>Cruise Control - Resume Start Target Offset vs Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control. Added to the target speed when resume is pressed below the set speed (in full from 0.5 km/h below the set speed), by vehicle speed. Stock all 0, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = resume starts with a higher target) Evidence: ledger:E1353</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.9" />
      <LABEL index="2" value="55.8" />
      <LABEL index="3" value="64.6" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.4" />
      <LABEL index="6" value="91.2" />
      <LABEL index="7" value="100.1" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.9" />
      <LABEL index="10" value="126.8" />
      <LABEL index="11" value="135.6" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.4" />
      <LABEL index="14" value="162.2" />
      <LABEL index="15" value="171.1" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21F98" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAD4" flags="0x30">
    <title>Cruise Control - Speed Error Gain, Holding</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control. Gain that turns the difference between vehicle speed and the cruise target into a change of the controller&#x27;s demand while cruise is holding speed, by that difference. Stock 16384 from 10 km/h below the target, 4096 at the target and 8192 from 1.7 km/h above. The demand is the controller&#x27;s internal scale. Shown raw. DO NOT EDIT. Effect: reference only (cruise speed holding) Evidence: ledger:E0899, ledger:E0943, ledger:E1353, ledger:E1361</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x22272" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>km/h (speed minus target)</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22296" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAD5" flags="0x30">
    <title>Cruise Control - Speed Error Gain, Resume / Accelerate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control. As the holding gain, but used while cruise resumes toward the set speed or accelerates. The demand is the controller&#x27;s internal scale. Shown raw. DO NOT EDIT. Effect: reference only (cruise resume and accelerate) Evidence: ledger:E0899, ledger:E0943, ledger:E1353, ledger:E1361</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x22272" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>km/h (speed minus target)</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x222BA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAD6" flags="0x30">
    <title>Cruise Control - Throttle Ramp-In Rate vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control. How fast the cruise throttle request rises from zero when cruise takes over the throttle, until it reaches what the controller asks for, by vehicle speed (a step every 50 ms). Stock 12 % throttle area per s at every speed. Effect: raise = cruise takes up the throttle faster Evidence: ledger:E1353</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.9" />
      <LABEL index="2" value="55.8" />
      <LABEL index="3" value="64.6" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.4" />
      <LABEL index="6" value="91.2" />
      <LABEL index="7" value="100.1" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.9" />
      <LABEL index="10" value="126.8" />
      <LABEL index="11" value="135.6" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.4" />
      <LABEL index="14" value="162.2" />
      <LABEL index="15" value="171.1" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22304" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% per s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>2000.000000</max>
      <MATH equation="X/32.7675"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAD7" flags="0x30">
    <title>Cruise Control - Speed Error Gain Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control. Speed differences (vehicle speed minus the cruise target) at which the two speed error gains are given. Stock -20 to 20 km/h, closer together near 0. Axis data: keep ascending. Effect: moves the points of both speed error gains Evidence: ledger:E1353</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22272" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xAD8" flags="0x0">
    <title>Cruise Control - Maximum Throttle Request (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control. Upper limit of the cruise throttle request; at the limit the target speed stops rising. Stock 100 %, which is never exceeded, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (lower = cruise cannot open the throttle further) Evidence: ledger:E1353</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x222FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAD9" flags="0x0">
    <title>Converter Heat Hot Mode - Leave Below (fluid temp) (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot mode entered by the converter heat count ends when transmission fluid temperature is below this, once it has stopped climbing for the hot mode minimum time. Stock 123 C. Part of the converter-heat hot-mode trigger: while the converter slips hard at speed with hot fluid, a heat count builds; past the limit the transmission goes into hot mode. The converter heat trigger is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = converter heat hot mode ends at a warmer fluid temperature (sooner)) Evidence: ledger:E1354, ledger:E1399</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DD3E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xADA" flags="0x30">
    <title>Converter Heat - Trigger Limit Temperature Breakpoints (axis, edit with care) (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission fluid temperature points of the converter heat trigger limit curve. Stock 50 to 146 C in 6 C steps. The limit curve is spread over these points, so moving them re-spaces it; keep the point count and keep the points rising. Part of the converter-heat hot-mode trigger: while the converter slips hard at speed with hot fluid, a heat count builds; past the limit the transmission goes into hot mode. The converter heat trigger is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (moves the temperature axis of the converter heat trigge...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DD66" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xADB" flags="0x30">
    <title>Converter Heat - Count Rate Divisor vs Speed Ratio (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While the converter heat count is armed, each pass adds 104448 / value to the heat count, by turbine / engine speed ratio (0 to 1 in 1/16 steps). Stock 4096 everywhere (25 per pass). Lower = the count builds faster. Part of the converter-heat hot-mode trigger: while the converter slips hard at speed with hot fluid, a heat count builds; past the limit the transmission goes into hot mode. The converter heat trigger is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (lower = hot mode from converter heat sooner) Evidence: ledger:E1354, ledger...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>speed ratio</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.0625" />
      <LABEL index="2" value="0.125" />
      <LABEL index="3" value="0.1875" />
      <LABEL index="4" value="0.25" />
      <LABEL index="5" value="0.3125" />
      <LABEL index="6" value="0.375" />
      <LABEL index="7" value="0.4375" />
      <LABEL index="8" value="0.5" />
      <LABEL index="9" value="0.5625" />
      <LABEL index="10" value="0.625" />
      <LABEL index="11" value="0.6875" />
      <LABEL index="12" value="0.75" />
      <LABEL index="13" value="0.8125" />
      <LABEL index="14" value="0.875" />
      <LABEL index="15" value="0.9375" />
      <LABEL index="16" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DDAE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>heat counts</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xADC" flags="0x30">
    <title>Alternate VE Blend Position vs Baro (airflow mode 2, inactive, DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Barometric blend position between the two alternate volumetric efficiency tables of the throttle-area airflow mode, by barometric pressure (40 to 104 kPa). The share of the first table grows as this value falls from 24320 to 17920. The stock calibration can never enter that airflow mode, so this has no effect. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: no effect on this truck Evidence: ledger:E0670, ledger:E0735, ledger:E0863, ledger:E0899, ledger:E1359</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="40" />
      <LABEL index="1" value="44" />
      <LABEL index="2" value="48" />
      <LABEL index="3" value="52" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="64" />
      <LABEL index="7" value="68" />
      <LABEL index="8" value="72" />
      <LABEL index="9" value="76" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="84" />
      <LABEL index="12" value="88" />
      <LABEL index="13" value="92" />
      <LABEL index="14" value="96" />
      <LABEL index="15" value="100" />
      <LABEL index="16" value="104" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C252" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xADD" flags="0x0">
    <title>Trans Fluid Life - Update Interval (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Seconds between wear count updates. Stock 255 s. Transmission fluid life monitor: a wear count builds with fluid temperature; life left is the part of the full life not yet used, and at or below the low life threshold the fluid deteriorated code is set. On the stock calibration the full life is the largest value and every wear weight is 0, so life never drops. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (lower = more frequent wear steps) Evidence: ledger:E1363</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCD2" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xADE" flags="0x0">
    <title>Trans Fluid Life - Low Life Threshold (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or below this life left the fluid deteriorated code is set. Stock 0 %. Transmission fluid life monitor: a wear count builds with fluid temperature; life left is the part of the full life not yet used, and at or below the low life threshold the fluid deteriorated code is set. On the stock calibration the full life is the largest value and every wear weight is 0, so life never drops. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = the code sets earlier) Evidence: ledger:E1363</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCD4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xADF" flags="0x0">
    <title>Trans Fluid Life - Life Left After Reset (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Life left written when the fluid life is reset. Stock 100 %. Transmission fluid life monitor: a wear count builds with fluid temperature; life left is the part of the full life not yet used, and at or below the low life threshold the fluid deteriorated code is set. On the stock calibration the full life is the largest value and every wear weight is 0, so life never drops. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1363</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCD6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAE0" flags="0x0">
    <title>Trans Fluid Life - Full Life (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wear count that uses up the whole fluid life. Stock 4294967295 (largest value). Transmission fluid life monitor: a wear count builds with fluid temperature; life left is the part of the full life not yet used, and at or below the low life threshold the fluid deteriorated code is set. On the stock calibration the full life is the largest value and every wear weight is 0, so life never drops. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (lower = shorter fluid life) Evidence: ledger:E1363</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCDA" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>wear counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>4294967295.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xAE1" flags="0x30">
    <title>Trans Fluid Life - Wear per Update vs Fluid Temp (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wear added to the fluid wear count at each update, by transmission fluid temperature (80 to 140 C). Stock 0 everywhere. Transmission fluid life monitor: a wear count builds with fluid temperature; life left is the part of the full life not yet used, and at or below the low life threshold the fluid deteriorated code is set. On the stock calibration the full life is the largest value and every wear weight is 0, so life never drops. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = fluid life used up faster at that temperature) Evidence: ledger:E1363</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (trans fluid)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="80" />
      <LABEL index="1" value="87.5" />
      <LABEL index="2" value="95" />
      <LABEL index="3" value="102.5" />
      <LABEL index="4" value="110" />
      <LABEL index="5" value="117.5" />
      <LABEL index="6" value="125" />
      <LABEL index="7" value="132.5" />
      <LABEL index="8" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DCE0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>wear counts</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAE2" flags="0x30">
    <title>Injector Circuit Fault Code by Cylinder Slot (reference)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Internal fault list index the injector circuit check reports for each cylinder slot: slots 1 to 5 report P0201, P0203, P0205, P0204 and P0202. Slots 6 to 8 are 0 (the H3 has 5 cylinders). Reference only: DO NOT EDIT. Effect: DO NOT EDIT (changes which fault code each injector reports) Evidence: ledger:E1366</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>cylinder slot</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3679E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fault index</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xAE3" flags="0x0">
    <title>Port Temperature Model Target - Engine Speed Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target temperature added per rpm of engine speed. Stock 0.0126 C per rpm. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = hotter target at higher engine speed Evidence: ledger:E1371</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2AAC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC per rpm</units>
    <decimalpl>4</decimalpl>
    <min>-1.000000</min>
    <max>0.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAE4" flags="0x0">
    <title>Port Temperature Model Target - Manifold Pressure Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target temperature added per kPa of manifold pressure. Stock -0.150 C per kPa. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = hotter target at higher manifold pressure Evidence: ledger:E1371</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2AAC6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC per kPa</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAE5" flags="0x0">
    <title>Port Temperature Model Target - Air-Fuel Ratio Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target temperature added per unit of effective air-fuel ratio (the average of the commanded air-fuel ratio and the Air-Fuel Ratio Offset). Stock 106.3 C per AFR. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = hotter target at leaner air-fuel ratio Evidence: ledger:E1371</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2AAC8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC per AFR</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAE6" flags="0x0">
    <title>Port Temperature Model Target - Air-Fuel Ratio Squared Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target temperature added per unit of effective air-fuel ratio squared. Stock -6.36 C. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = hotter target, more so at leaner air-fuel ratio Evidence: ledger:E1371</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2AACA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC per AFR squared</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAE7" flags="0x0">
    <title>Port Temperature Model Target - Spark Retard Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target temperature added per degree of spark retard from best torque timing (the torque model&#x27;s optimal spark minus actual spark, zero when not retarded). Stock -1.64 C per degree. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = hotter target with spark retard Evidence: ledger:E1371</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2AACC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC per deg</units>
    <decimalpl>0</decimalpl>
    <min>-4.000000</min>
    <max>3.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAE8" flags="0x0">
    <title>Port Temperature Model Target - Coolant Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target temperature added per degree of coolant temperature. Stock 1.035. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = hotter target with a hotter engine Evidence: ledger:E1371</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2AACE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC per degC</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAE9" flags="0x0">
    <title>Port Temperature Model Target - Constant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Constant added to the target temperature. Stock -317.7 C. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = hotter target everywhere Evidence: ledger:E1371</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2AAD0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-1024.000000</min>
    <max>1023.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAEA" flags="0x0">
    <title>Injector Circuit Test - Voltage OK Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The injector circuit fault checks (P0201 to P0205) start once system voltage has stayed above the Injector Circuit Test - System Voltage Minimum for longer than this. Stock 5.0 s. Effect: raise = the injector circuit checks wait longer after voltage recovers Evidence: ledger:E1372</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36798" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xAEB" flags="0x30">
    <title>Trans Hot Mode, Rapid Rise - Rate Limit vs Fluid Temp (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rapid rise hot mode starts when transmission fluid temperature is at or above the rapid rise arm temperature and rising at least this fast, by fluid temperature (70 to 150 C). Stock 25.5 C per minute up to 110 C, 23 at 115 C, 10 at 120 C, 2 at 125 C and 0 from 130 C. Rapid rise hot mode is a second way into transmission hot mode (hot shift and converter clutch schedules) when the fluid temperature climbs quickly; it is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (lower = rapid rise hot mode starts on a slower climb) Evidence: ledger:E1373</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (trans fluid)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="70" />
      <LABEL index="1" value="75" />
      <LABEL index="2" value="80" />
      <LABEL index="3" value="85" />
      <LABEL index="4" value="90" />
      <LABEL index="5" value="95" />
      <LABEL index="6" value="100" />
      <LABEL index="7" value="105" />
      <LABEL index="8" value="110" />
      <LABEL index="9" value="115" />
      <LABEL index="10" value="120" />
      <LABEL index="11" value="125" />
      <LABEL index="12" value="130" />
      <LABEL index="13" value="135" />
      <LABEL index="14" value="140" />
      <LABEL index="15" value="145" />
      <LABEL index="16" value="150" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DD42" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC/min</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xAEC" flags="0x0">
    <title>P0502 Test - Run Condition, Engine Torque Maximum in Park / Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): in park or neutral the check runs only with engine torque at or below this (the drive range limits do not apply there). Stock 8191.9 Nm; with the stock minimum the check does not run in park or neutral. Effect: together with the minimum: lets the check run in park or neutral Evidence: ledger:E1374</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F82E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAED" flags="0x0">
    <title>P0502 Test - Run Condition, Engine Torque Minimum in Park / Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): in park or neutral the check runs only with engine torque at or above this. Stock 8191.9 Nm, so the check does not run in park or neutral. Effect: lower = the check can run in park or neutral Evidence: ledger:E1374</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F830" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAEE" flags="0x0">
    <title>P2764 Test - Alternate Mode, Fault Duty Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2764 (converter clutch pulse width solenoid circuit), alternate mode: at or above this commanded duty a driver fault latch counts as a fault sample. Stock 90 %. Used only in an alternate check mode that is not selected on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1375</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F68E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAEF" flags="0x0">
    <title>P2764 Test - Alternate Mode, Good Sample Duty Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2764 (converter clutch pulse width solenoid circuit), alternate mode: lowest commanded duty at which a sample with no driver fault counts as good. Stock 65 %. Used only in an alternate check mode that is not selected on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1375</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F690" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAF0" flags="0x0">
    <title>P2771 Test - Alternate Mode, Vehicle Speed Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2771 (four wheel drive low switch circuit), alternate mode: the check arms in any gear only at or above this vehicle speed. Stock 3 km/h. Used only in an alternate check mode that is not selected on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1375</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F74C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAF1" flags="0x0">
    <title>Trans Abuse Mode - Fixed Torque Limit (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Trans abuse mode: engine torque limit used in place of the torque reduction vs rpm table when the fixed limit is selected. Stock 827 Nm. The stock calibration uses the table, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1378</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3EA88" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAF2" flags="0x0">
    <title>Trans Abuse Mode - Engine Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Trans abuse mode: engine speed above which an engagement counts as abuse. Stock 2000 rpm. An engagement from park or neutral into drive or reverse at low speed in 1st or 2nd with engine speed above the engine speed limit, or throttle at or above the throttle limit, is treated as abuse and the abuse torque reduction is applied. Effect: raise = higher engine speed allowed during engagement before the torque cut Evidence: ledger:E1378</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3EA8C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAF3" flags="0x0">
    <title>Trans Abuse Mode - Throttle Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Trans abuse mode: throttle at or above which an engagement counts as abuse. Stock 20 %. An engagement from park or neutral into drive or reverse at low speed in 1st or 2nd with engine speed above the engine speed limit, or throttle at or above the throttle limit, is treated as abuse and the abuse torque reduction is applied. Effect: raise = more throttle allowed during engagement before the torque cut Evidence: ledger:E1378</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3EA90" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAF4" flags="0x0">
    <title>Trans Abuse Mode - Highest Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Trans abuse mode: an engagement counts as abuse only with the transmission in this gear or lower (0 = 1st, 1 = 2nd). Stock 1 (2nd). An engagement from park or neutral into drive or reverse at low speed in 1st or 2nd with engine speed above the engine speed limit, or throttle at or above the throttle limit, is treated as abuse and the abuse torque reduction is applied. Effect: lower = abuse detection only in 1st Evidence: ledger:E1378</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3EB04" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gear index</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAF5" flags="0x0">
    <title>Shift Sol Tests, 5th Gear Ratio Confirm - Ratio Min (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid tests, 5th gear position: bottom of the estimated gear ratio window that counts as the right gear. Stock window 2.600 to 3.300. Used only in the five speed gear layout, which this transmission does not use (the gear count is 4), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F592" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAF6" flags="0x0">
    <title>Shift Sol Tests, 5th Gear Ratio Confirm - Ratio Max (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid tests, 5th gear position: top of the estimated gear ratio window that counts as the right gear. Stock window 2.600 to 3.300. Used only in the five speed gear layout, which this transmission does not use (the gear count is 4), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F594" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAF7" flags="0x0">
    <title>Shift Sol C Test (P0761), 4th - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0761 (shift solenoid C performance test), 4th gear: time since the last shift before the test watches the transmission. Stock 0 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAF8" flags="0x0">
    <title>Shift Sol C Test (P0762), 5th - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0762 (shift solenoid C performance test), 5th gear position: time since the last shift before the test watches the transmission. Stock 0 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAF9" flags="0x0">
    <title>Shift Sol Tests, 5th Gear Ratio Confirm - Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid tests, 5th gear position: time the ratio must stay inside the right ratio window without a break. Stock 1 s. Used only in the five speed gear layout, which this transmission does not use (the gear count is 4), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5C6" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAFA" flags="0x0">
    <title>Shift Sol C Test (P0761), 4th - Torque Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0761 (shift solenoid C performance test), 4th gear: lowest engine torque at which the test watches the transmission. Stock 65 Nm. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5D8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAFB" flags="0x0">
    <title>Shift Sol C Test (P0762), 5th - Torque Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0762 (shift solenoid C performance test), 5th gear position: lowest engine torque at which the test watches the transmission. Stock 65 Nm. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5DA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAFC" flags="0x0">
    <title>Shift Sol Tests, 5th Gear Decision - Torque Min (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid tests, 5th gear position: lowest engine torque at which the tests can reach a decision. Stock 47 Nm. Used only in the five speed gear layout, which this transmission does not use (the gear count is 4), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAFD" flags="0x0">
    <title>Shift Sol C Test (P0761), 4th - Torque Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0761 (shift solenoid C performance test), 4th gear: highest engine torque at which the test watches the transmission. Stock 550 Nm. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAFE" flags="0x0">
    <title>Shift Sol C Test (P0762), 5th - Torque Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0762 (shift solenoid C performance test), 5th gear position: highest engine torque at which the test watches the transmission. Stock 550 Nm. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F5F8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xAFF" flags="0x0">
    <title>Shift Sol Tests, 5th Gear Decision - Torque Max (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid tests, 5th gear position: highest engine torque at which the tests can reach a decision. Stock 550 Nm. Used only in the five speed gear layout, which this transmission does not use (the gear count is 4), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F602" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB00" flags="0x0">
    <title>Shift Sol C Test (P0761), 4th - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0761 (shift solenoid C performance test), 4th gear: lowest throttle at which the test watches the transmission. Stock 0 %. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F614" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB01" flags="0x0">
    <title>Shift Sol C Test (P0762), 5th - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0762 (shift solenoid C performance test), 5th gear position: lowest throttle at which the test watches the transmission. Stock 0 %. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F616" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB02" flags="0x0">
    <title>Shift Sol Tests, 5th Gear Decision - Throttle Min (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid tests, 5th gear position: lowest throttle at which the tests can reach a decision. Stock 0 %. Used only in the five speed gear layout, which this transmission does not use (the gear count is 4), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F620" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB03" flags="0x0">
    <title>Shift Sol C Test (P0761), 4th - Converter Slip Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0761 (shift solenoid C performance test), 4th gear: lowest torque converter slip at which the test watches the transmission. Stock 0 rpm. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F626" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB04" flags="0x0">
    <title>Shift Sol C Test (P0761), 4th - Converter Slip Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0761 (shift solenoid C performance test), 4th gear: highest torque converter slip at which the test watches the transmission. Stock 0 rpm. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F628" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB05" flags="0x0">
    <title>Shift Sol C Test (P0762), 5th - Converter Slip Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0762 (shift solenoid C performance test), 5th gear position: lowest torque converter slip at which the test watches the transmission. Stock 0 rpm. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F62A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB06" flags="0x0">
    <title>Shift Sol C Test (P0762), 5th - Converter Slip Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0762 (shift solenoid C performance test), 5th gear position: highest torque converter slip at which the test watches the transmission. Stock 0 rpm. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1381</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F62C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB07" flags="0x0">
    <title>DFCO - Catalyst Hot Keep Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the catalyst-hot state is set it is kept while the catalyst model temperature stays at or above this (stock 0 C: kept until the next fuel cut request). Deceleration fuel cut (DFCO): once all the fuel cut conditions hold, fuel is cut only after this delay; the delay restarts whenever the conditions drop out or the gear changes. The catalyst-hot state is set when the catalyst model temperature reaches the hot temperature and lasts until the next fuel cut request. Effect: raise = the short delay ends when the catalyst cools below this Evidence: ledger:E0415, ledger:E1382</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2F4D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB08" flags="0x0">
    <title>DFCO - Entry Delay, Catalyst Hot</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel cut delay used while the catalyst is hot (stock 3 s). Deceleration fuel cut (DFCO): once all the fuel cut conditions hold, fuel is cut only after this delay; the delay restarts whenever the conditions drop out or the gear changes. The catalyst-hot state is set when the catalyst model temperature reaches the hot temperature and lasts until the next fuel cut request. Effect: lower = fuel is cut sooner on deceleration with a hot catalyst Evidence: ledger:E0415, ledger:E1382</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2F4F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB09" flags="0x30">
    <title>DFCO - Entry Delay by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel cut delay by gear (stock 11 s in 1st, 3 s in 2nd, 6 s in 3rd, 8 s in 4th). Deceleration fuel cut (DFCO): once all the fuel cut conditions hold, fuel is cut only after this delay; the delay restarts whenever the conditions drop out or the gear changes. Effect: lower = fuel is cut sooner on deceleration in that gear Evidence: ledger:E0415, ledger:E1382</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>gear (trans state 0..5)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="5th" />
      <LABEL index="5" value="6th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F4F4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB0A" flags="0x0">
    <title>Downshift Base Pressure - Leave Out Learned Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = the learned shift pressure is not added to the downshift base pressure in the normal and top gear high torque sources. Stock 1 (downshifts do not use it). Part of the adaptive shift pressure learning (TAP). Effect: 0 = downshifts also get the learned shift pressure Evidence: ledger:E1030, ledger:E1383</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3A08E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0/1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB0B" flags="0x0">
    <title>Shift Pressure - Leave Out Learned Pressure in 4WD Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = in 4WD Low the learned shift pressure is not added to the upshift or downshift base pressure. Stock 1. Part of the adaptive shift pressure learning (TAP). Effect: 0 = 4WD Low shifts also get the learned shift pressure Evidence: ledger:E1030, ledger:E1383</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3A094" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0/1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB0C" flags="0x30">
    <title>Upshift Pressure - Learned Pressure at Any Torque State</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = the learned shift pressure is added to that upshift&#x27;s base pressure in every torque state; 0 = only in the high torque state (power on). Stock 0 for all three. Part of the adaptive shift pressure learning (TAP). Effect: 1 = learned pressure also on light-torque upshifts Evidence: ledger:E1030, ledger:E1383</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A0A0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>0/1</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB0D" flags="0x0">
    <title>Shift Adapt - No Learning in Hot Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = shifts made while the transmission hot mode is active are not used for learning. Stock 1. Part of the adaptive shift pressure learning (TAP). Effect: 0 = also learn in hot mode Evidence: ledger:E1030, ledger:E1383</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C00A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0/1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB0E" flags="0x30">
    <title>Shift Adapt - No Learning by Upshift Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = shifts made in that upshift set are not used for learning (sets as chosen by Shift Set by Drive Mode). Stock 0 for set 0, 1 for set 1 and set 2 (4WD Low). Part of the adaptive shift pressure learning (TAP). Effect: 0 = learn in that set Evidence: ledger:E1030, ledger:E1383</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>upshift set</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C00C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>0/1</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB0F" flags="0x0">
    <title>Shift Adapt - No Learning in 4WD Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = shifts made in 4WD Low are not used for learning. Stock 1. Part of the adaptive shift pressure learning (TAP). Effect: 0 = also learn in 4WD Low Evidence: ledger:E1030, ledger:E1383</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C012" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0/1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB10" flags="0x30">
    <title>Shift Adapt - Learning Allowed by Shift and Range</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = that upshift (rows) is used for learning in that transmission range code (columns); 0 = not. Stock on for range codes 2 and 3, 1-2 and 2-3 only. Part of the adaptive shift pressure learning (TAP). Effect: 1 = allow learning there Evidence: ledger:E1030, ledger:E1383</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>range code</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C014" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>0/1</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB11" flags="0x30">
    <title>Torque-Based Upshift Inhibit - Enable by Range</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = the torque-based upshift inhibit runs in that transmission range code (together with Enable by Shift Mode). Stock on for range codes 2 and 3. An upshift is held off when the torque predicted after it would be below what the truck needs now. Effect: whether upshifts can be held for lack of torque in that range Evidence: ledger:E1030, ledger:E1383</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>range code</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3911E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>0/1</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB12" flags="0x30">
    <title>Top Gear Flag by Range and Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = with that transmission range code (rows) and current gear (columns) the transmission counts as in its top gear (no upshift available). This selects the top gear shift pressure sources and line pressure mode 1. Stock: range code 0 at 1st and 2nd, 1 at 2nd, 2 at 3rd, 3 at 4th. 4th gear always counts as top gear. Effect: moves where the top gear pressure behaviour starts Evidence: ledger:E1030, ledger:E1383</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>8</indexcount>
      <units>range code</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38A70" mmedelementsizebits="16" mmedrowcount="8" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>0/1</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB13" flags="0x30">
    <title>Fuel Temperature Model - Update Rate vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the modelled fuel temperature moves toward its target, by mass airflow: each update closes this fraction of the gap (stock 0.25 at 0 g/s rising to 1.0 from 96 g/s). The PCM models fuel temperature from engine coolant and intake air temperature; the model sets how injector offset is corrected for fuel temperature. Effect: raise = the modelled fuel temperature follows its target faster at that airflow Evidence: ledger:E1278, ledger:E1384</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28EDE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB14" flags="0x0">
    <title>Fuel Temperature Model - Coolant Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of engine coolant temperature in the modelled fuel temperature target (stock 0.35). The PCM models fuel temperature from engine coolant and intake air temperature; the model sets how injector offset is corrected for fuel temperature. Effect: raise = the modelled fuel temperature leans toward coolant temperature Evidence: ledger:E1278, ledger:E1384</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28ED6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB15" flags="0x0">
    <title>Fuel Temperature Model - Intake Air Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of intake air temperature in the modelled fuel temperature target (stock 0.65). The PCM models fuel temperature from engine coolant and intake air temperature; the model sets how injector offset is corrected for fuel temperature. Effect: raise = the modelled fuel temperature leans toward intake air temperature Evidence: ledger:E1278, ledger:E1384</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28ED4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB16" flags="0x0">
    <title>TCC Release Ramp - Time Limit After Tip-In Release (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a tip-in release, the release ramp ends and the clutch pressure drops to zero once this time has passed in the ramp (stock 2.0 s). TCC tip-in release: when the throttle request rises faster than the rate threshold (change per update), the PCM releases the converter clutch and holds it released for the hold time. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: lower = a release ramp after a tip-in release is cut short sooner Evidence: ledger:E1385</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D464" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB17" flags="0x30">
    <title>Pre-Sync Start Pulses - Minimum Run Time vs Coolant (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The sequence is also allowed once engine run time is above this (stock 0 s). Pre-sync start pulses: an optional sequence of fuel pulses at cranking, before the PCM has synchronised to the crankshaft. It is switched off on this calibration, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1387</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x26CE4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25624" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB18" flags="0x30">
    <title>Pre-Sync Start Pulses - Start Delay vs Coolant (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once cranking arms the sequence, the pulses start after this time (stock 0 s). Pre-sync start pulses: an optional sequence of fuel pulses at cranking, before the PCM has synchronised to the crankshaft. It is switched off on this calibration, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = later start pulses) Evidence: ledger:E1387</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x26CE4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25600" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB19" flags="0x30">
    <title>Cold Weather TCC Offset - Apply Speed</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch apply speed by throttle (columns) and gear (rows). Part of the cold weather offset, weighted from full to none by the Cold Weather Shift Offset temperatures. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (positive = later apply when cold) Evidence: ledger:E0177, ledger:E1027, ledger:E1390</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CB22" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB1A" flags="0x30">
    <title>Cold Weather TCC Offset - Release Speed</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch release speed by throttle (columns) and gear (rows). Part of the cold weather offset, weighted from full to none by the Cold Weather Shift Offset temperatures. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (positive = earlier release when cold) Evidence: ledger:E0177, ledger:E1027, ledger:E1390</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CB5B" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB1B" flags="0x30">
    <title>3rd Gear Range TCC Speed Correction - Apply, Cruise</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch apply speed by throttle (columns) and gear (rows). Used only in range code 2 (the range whose shifts stop at 3rd), in that shift mode. Stock 0. Effect: positive = higher apply speed in that range Evidence: ledger:E0177, ledger:E1027, ledger:E1390</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CC78" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB1C" flags="0x30">
    <title>3rd Gear Range TCC Speed Correction - Apply, 4-Lo</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch apply speed by throttle (columns) and gear (rows). Used only in range code 2 (the range whose shifts stop at 3rd), in that shift mode. Stock 0. Effect: positive = higher apply speed in that range Evidence: ledger:E0177, ledger:E1027, ledger:E1390</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CCB1" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB1D" flags="0x30">
    <title>3rd Gear Range TCC Speed Correction - Apply, Normal</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch apply speed by throttle (columns) and gear (rows). Used only in range code 2 (the range whose shifts stop at 3rd), in that shift mode. Stock 0. Effect: positive = higher apply speed in that range Evidence: ledger:E0177, ledger:E1027, ledger:E1390</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CC3F" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB1E" flags="0x30">
    <title>3rd Gear Range TCC Speed Correction - Release, Cruise</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch release speed by throttle (columns) and gear (rows). Used only in range code 2 (the range whose shifts stop at 3rd), in that shift mode. Stock 0. Effect: positive = higher release speed in that range Evidence: ledger:E0177, ledger:E1027, ledger:E1390</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CBCD" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB1F" flags="0x30">
    <title>3rd Gear Range TCC Speed Correction - Release, 4-Lo</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch release speed by throttle (columns) and gear (rows). Used only in range code 2 (the range whose shifts stop at 3rd), in that shift mode. Stock 0. Effect: positive = higher release speed in that range Evidence: ledger:E0177, ledger:E1027, ledger:E1390</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CC06" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB20" flags="0x30">
    <title>3rd Gear Range TCC Speed Correction - Release, Normal</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch release speed by throttle (columns) and gear (rows). Used only in range code 2 (the range whose shifts stop at 3rd), in that shift mode. Stock 0. Effect: positive = higher release speed in that range Evidence: ledger:E0177, ledger:E1027, ledger:E1390</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CB94" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB21" flags="0x30">
    <title>Altitude Offset Weight vs Baro (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How much of the altitude offsets is used, by barometric pressure (1.0 = all). The altitude offsets move the shift speeds, the WOT shift rpm and the converter clutch apply and release speeds. Stock 0 everywhere: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = altitude offsets apply at that pressure) Evidence: ledger:E0838, ledger:E1027, ledger:E1391</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="50" />
      <LABEL index="1" value="58" />
      <LABEL index="2" value="66" />
      <LABEL index="3" value="74" />
      <LABEL index="4" value="82" />
      <LABEL index="5" value="90" />
      <LABEL index="6" value="98" />
      <LABEL index="7" value="106" />
      <LABEL index="8" value="114" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39ECA" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>weight</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>0.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB22" flags="0x30">
    <title>Altitude Shift Offset - Upshift Speed, Normal</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the upshift speed in the normal shift mode, by throttle (columns) and upshift (rows). Part of the altitude offset, scaled by the Altitude Offset Weight (by barometric pressure). Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0838, ledger:E1027, ledger:E1391</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>upshift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38EA9" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB23" flags="0x30">
    <title>Altitude Offset - WOT Shift RPM (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the wide open throttle shift rpm by current gear. Part of the altitude offset, scaled by the Altitude Offset Weight (by barometric pressure). Stock the weight is 0 everywhere and this table is 0, so it has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0838, ledger:E1027, ledger:E1391</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38FC6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>-4096.000000</min>
      <max>4095.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB24" flags="0x30">
    <title>Altitude TCC Offset - Apply Speed, Hot Modes (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch apply speed in the trans hot and coolant hot modes, by throttle (columns) and gear (rows). Part of the altitude offset, scaled by the Altitude Offset Weight (by barometric pressure). Stock the weight is 0 everywhere and this table is 0, so it has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0838, ledger:E1027, ledger:E1391</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C95A" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB25" flags="0x30">
    <title>Altitude TCC Offset - Release Speed, Hot Modes (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch release speed in the trans hot and coolant hot modes, by throttle (columns) and gear (rows). Part of the altitude offset, scaled by the Altitude Offset Weight (by barometric pressure). Stock the weight is 0 everywhere and this table is 0, so it has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0838, ledger:E1027, ledger:E1391</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CA3E" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB26" flags="0x30">
    <title>Altitude TCC Offset - Apply Speed, Cruise (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch apply speed in the cruise modes, by throttle (columns) and gear (rows). Part of the altitude offset, scaled by the Altitude Offset Weight (by barometric pressure). Stock the weight is 0 everywhere and this table is 0, so it has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0838, ledger:E1027, ledger:E1391</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C993" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB27" flags="0x30">
    <title>Altitude TCC Offset - Release Speed, Cruise (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch release speed in the cruise modes, by throttle (columns) and gear (rows). Part of the altitude offset, scaled by the Altitude Offset Weight (by barometric pressure). Stock the weight is 0 everywhere and this table is 0, so it has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0838, ledger:E1027, ledger:E1391</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CA77" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB28" flags="0x30">
    <title>Altitude TCC Offset - Apply Speed, 4-Lo (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch apply speed in the 4-Lo modes, by throttle (columns) and gear (rows). Part of the altitude offset, scaled by the Altitude Offset Weight (by barometric pressure). Stock the weight is 0 everywhere and this table is 0, so it has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0838, ledger:E1027, ledger:E1391</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C9CC" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB29" flags="0x30">
    <title>Altitude TCC Offset - Release Speed, 4-Lo (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch release speed in the 4-Lo modes, by throttle (columns) and gear (rows). Part of the altitude offset, scaled by the Altitude Offset Weight (by barometric pressure). Stock the weight is 0 everywhere and this table is 0, so it has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0838, ledger:E1027, ledger:E1391</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CAB0" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB2A" flags="0x30">
    <title>Altitude TCC Offset - Apply Speed, Normal (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch apply speed in the normal modes, by throttle (columns) and gear (rows). Part of the altitude offset, scaled by the Altitude Offset Weight (by barometric pressure). Stock the weight is 0 everywhere and this table is 0, so it has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0838, ledger:E1027, ledger:E1391</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CA05" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB2B" flags="0x30">
    <title>Altitude TCC Offset - Release Speed, Normal (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the converter clutch release speed in the normal modes, by throttle (columns) and gear (rows). Part of the altitude offset, scaled by the Altitude Offset Weight (by barometric pressure). Stock the weight is 0 everywhere and this table is 0, so it has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0838, ledger:E1027, ledger:E1391</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="6.25" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="25" />
      <LABEL index="7" value="31.25" />
      <LABEL index="8" value="37.5" />
      <LABEL index="9" value="43.75" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="56.25" />
      <LABEL index="12" value="62.5" />
      <LABEL index="13" value="68.75" />
      <LABEL index="14" value="75" />
      <LABEL index="15" value="81.25" />
      <LABEL index="16" value="87.5" />
      <LABEL index="17" value="93.75" />
      <LABEL index="18" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2nd" />
      <LABEL index="1" value="3rd" />
      <LABEL index="2" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CAE9" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mph</units>
      <decimalpl>1</decimalpl>
      <min>-39.767757</min>
      <max>39.457071</max>
      <MATH equation="X*0.3106856"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB2C" flags="0x0">
    <title>Turbine Speed - Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of the change in turbine speed taken into the filtered turbine speed each update (stock 0.314). Effect: raise = the filtered turbine speed follows faster Evidence: ledger:E0354, ledger:E0859, ledger:E1392</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C89A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB2D" flags="0x30">
    <title>TCC Pressure Offset - Line Pressure Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Line pressure points of the TCC pressure offset curve (stock 0 to 640 kPa in 80 kPa steps). Axis data: keep ascending. Effect: moves the line pressure points of that curve Evidence: ledger:E0354, ledger:E0859, ledger:E1392</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C8B6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB2E" flags="0x30">
    <title>Idle Airflow Closed-Loop Mode 2 - MAP Error Breakpoints (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Manifold pressure error breakpoints (measured minus the mode 2 MAP target, after the error gain) for the mode 2 closed-loop step table. Stock -16 to +16 kPa in 2 kPa steps. Mode 2 runs only when the closed loop mode select is not 1; it is 1 on the stock calibration, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1393</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>cell of the mode 2 step table</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29502" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB2F" flags="0x30">
    <title>Idle Airflow Closed-Loop Mode 2 - Step vs MAP Error (dormant)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow integral step per update by manifold pressure error in the alternate (MAP based) closed-loop mode, the counterpart of Idle Airflow Closed-Loop Step vs Airflow Error. Row 1 = In Gear, row 2 = Park / Neutral. Stock all 0. Mode 2 runs only when the closed loop mode select is not 1; it is 1 on the stock calibration, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1393</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x29500" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT; data columns: kPa MAP error)</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>transmission</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="In Gear" />
      <LABEL index="1" value="Park / Neutral" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x292AA" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s per update</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB30" flags="0x30">
    <title>Fuel Cut List - 1 Cylinder (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the PCM cuts fuel to 1 cylinder, these are the injector outputs it switches off (0 = the first output). Stock: outputs 0 to 0. Used by the cylinder cut feature that runs the engine on fewer cylinders. Reference only: DO NOT EDIT. Effect: reference only (which injectors a cylinder cut turns off) Evidence: ledger:E1398</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>1</indexcount>
      <units>list position</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x266C6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="1" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>injector output</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB31" flags="0x30">
    <title>Fuel Cut List - 2 Cylinders (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the PCM cuts fuel to 2 cylinders, these are the injector outputs it switches off (0 = the first output). Stock: outputs 0 to 1. Used by the cylinder cut feature that runs the engine on fewer cylinders. Reference only: DO NOT EDIT. Effect: reference only (which injectors a cylinder cut turns off) Evidence: ledger:E1398</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>list position</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x266C8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>injector output</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB32" flags="0x30">
    <title>Fuel Cut List - 3 Cylinders (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the PCM cuts fuel to 3 cylinders, these are the injector outputs it switches off (0 = the first output). Stock: outputs 0 to 2. Used by the cylinder cut feature that runs the engine on fewer cylinders. Reference only: DO NOT EDIT. Effect: reference only (which injectors a cylinder cut turns off) Evidence: ledger:E1398</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>list position</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x266CC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>injector output</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB33" flags="0x30">
    <title>Fuel Cut List - 4 Cylinders (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the PCM cuts fuel to 4 cylinders, these are the injector outputs it switches off (0 = the first output). Stock: outputs 0 to 3. Used by the cylinder cut feature that runs the engine on fewer cylinders. Reference only: DO NOT EDIT. Effect: reference only (which injectors a cylinder cut turns off) Evidence: ledger:E1398</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>list position</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x266D2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>injector output</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB34" flags="0x30">
    <title>Fuel Cut List - 5 Cylinders (DO NOT EDIT, not used on this engine)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the PCM cuts fuel to 5 cylinders, these are the injector outputs it switches off (0 = the first output). Stock: outputs 0 to 4. This engine has five cylinders and cuts all five without a list, so this list is not used (dormant). Reference only: DO NOT EDIT. Effect: reference only (which injectors a cylinder cut turns off) Evidence: ledger:E1398</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>list position</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x266DA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>injector output</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB35" flags="0x30">
    <title>Fuel Cut List - 6 Cylinders (DO NOT EDIT, not used on this engine)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the PCM cuts fuel to 6 cylinders, these are the injector outputs it switches off (0 = the first output). Stock: outputs 0 to 5. This engine has five cylinders and cuts all five without a list, so this list is not used (dormant). Reference only: DO NOT EDIT. Effect: reference only (which injectors a cylinder cut turns off) Evidence: ledger:E1398</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>list position</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x266E4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>injector output</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB36" flags="0x30">
    <title>Fuel Cut List - 7 Cylinders (DO NOT EDIT, not used on this engine)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the PCM cuts fuel to 7 cylinders, these are the injector outputs it switches off (0 = the first output). Stock: outputs 0 to 6. This engine has five cylinders and cuts all five without a list, so this list is not used (dormant). Reference only: DO NOT EDIT. Effect: reference only (which injectors a cylinder cut turns off) Evidence: ledger:E1398</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>list position</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x266F0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>injector output</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB37" flags="0x0">
    <title>P1750 Test - Throttle Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1750 (2nd gear ratio check): runs only with throttle at or above this. Stock 0 %. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1400</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F506" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB38" flags="0x0">
    <title>P1750 Test - Vehicle Speed Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1750 (2nd gear ratio check): runs only with vehicle speed at or above this. Stock 0 km/h. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1400</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F508" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB39" flags="0x0">
    <title>P1750 Test - Fluid Temperature Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1750 (2nd gear ratio check): runs only with transmission fluid at or above this. Stock 0 C. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1400</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F50A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB3A" flags="0x0">
    <title>P1750 Test - Engine Torque Maximum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1750 (2nd gear ratio check): runs only with engine torque at or below this. Stock 0 Nm. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1400</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F50C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB3B" flags="0x0">
    <title>P1750 Test - Engine Torque Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1750 (2nd gear ratio check): runs only with engine torque at or above this. Stock 0 Nm. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1400</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F50E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB3C" flags="0x0">
    <title>P1750 Test - Time in 2nd Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1750 (2nd gear ratio check): time in 2nd gear before the ratio is judged. Stock 0 s. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1400</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F510" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB3D" flags="0x0">
    <title>P1750 Pass - Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1750 (2nd gear ratio check): time with the measured gear ratio inside the pass window that passes the check. Stock 0 s. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1400</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F512" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB3E" flags="0x0">
    <title>P1750 Fail - Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1750 (2nd gear ratio check): time with the measured gear ratio inside the fail window that sets the code. Stock 0 s. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1400</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F514" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB3F" flags="0x0">
    <title>P1750 Fail - Ratio Window Max (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1750 (2nd gear ratio check): top of the measured gear ratio window that counts as a fault. Stock 0. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1400</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F516" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB40" flags="0x0">
    <title>P1750 Fail - Ratio Window Min (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1750 (2nd gear ratio check): bottom of the measured gear ratio window that counts as a fault. Stock 0. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1400</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F518" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB41" flags="0x0">
    <title>P1750 Pass - Ratio Window Max (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1750 (2nd gear ratio check): top of the measured gear ratio window that counts as good. Stock 0. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1400</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F51A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB42" flags="0x0">
    <title>P1750 Pass - Ratio Window Min (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1750 (2nd gear ratio check): bottom of the measured gear ratio window that counts as good. Stock 0. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1400</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F51C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB43" flags="0x0">
    <title>TCC Line Pressure Release - Re-Apply Margin (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With the line pressure check turned on (off on the stock calibration), the converter clutch is ramped off when line pressure rises above the TCC pressure ceiling, and stays released until line pressure is at least this much below the ceiling (stock 0 kPa). This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1404</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D244" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB44" flags="0x0">
    <title>TCC Apply - Solenoid Lead Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the converter clutch applies, the clutch solenoid is switched on this long with zero clutch pressure before the pressure control starts (stock 0.15 s). Effect: raise = longer delay between the solenoid switching on and the clutch starting to apply Evidence: ledger:E1405</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D430" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB45" flags="0x0">
    <title>TCC On Target - Pressure Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra converter clutch pressure added while slip is held on target, on top of the load based pressure and the slip controller (stock 200 kPa; the total is capped at the full apply pressure). Effect: raise = firmer clutch hold while on target (less slip); lower = softer Evidence: ledger:E1406</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D172" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB46" flags="0x0">
    <title>TCC Release Ramp - Rate After Tip-In Release (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the converter clutch pressure ramps down after a tip-in release (stock 879 kPa/s). TCC tip-in release: when the throttle request rises faster than the rate threshold, the PCM releases the converter clutch. Inactive on stock: the live thresholds are a 100 % step per update, which cannot be exceeded. Effect: no effect on the stock calibration (the tip-in release never fires on stock) Evidence: ledger:E1406</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D176" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>1000.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65.535"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB47" flags="0x0">
    <title>TCC Operating Point - Torque Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter clutch base pressure added per Nm of engine torque (stock 2.0 kPa per Nm). Together with the base curve it sets the load based clutch pressure the slip controller works around. Effect: raise = more clutch pressure per Nm of torque (firmer under load) Evidence: ledger:E1407</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D174" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa/Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB48" flags="0x30">
    <title>TCC Operating Point - Base by Turbine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter clutch base pressure by transmission input (turbine) speed, before the torque term is added (stock -25 kPa at every speed). Effect: raise = more clutch pressure at that turbine speed Evidence: ledger:E1407</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3D05C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (turbine)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D020" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB49" flags="0x30">
    <title>TCC Operating Point - Turbine Speed Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission input (turbine) speed (800 to 6400 rpm): breakpoints of TCC Operating Point - Base by Turbine Speed. Axis data: keep ascending. Effect: moves the table points it indexes Evidence: ledger:E1407</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D05C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB4A" flags="0x0">
    <title>Traction Control Gear Request - Maximum Throttle Rise (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control gear request: an active request is cancelled when the driver throttle area rises faster than this (stock 20 % per 25 ms). On this calibration the gear request is not applied to the shift schedule (inactive). Effect: no effect on this truck (raise = the request survives a faster tip-in) Evidence: ledger:E0269, ledger:E0436, ledger:E0925, ledger:E1412</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30358" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% per 25 ms</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB4B" flags="0x0">
    <title>Traction Control Gear Request - Hold Time, 3rd Gear (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control gear request: time a 3rd gear request is held before it steps down to 2nd (stock 5 s). On this calibration the gear request is not applied to the shift schedule (inactive). Effect: no effect on this truck (raise = a 3rd gear request lasts longer) Evidence: ledger:E0269, ledger:E0436, ledger:E0925, ledger:E1412</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3035A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB4C" flags="0x0">
    <title>Traction Control Gear Request - Hold Time, 2nd Gear (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control gear request: time a 2nd gear request is held before it steps down to 1st (stock 1 s). On this calibration the gear request is not applied to the shift schedule (inactive). Effect: no effect on this truck (raise = a 2nd gear request lasts longer) Evidence: ledger:E0269, ledger:E0436, ledger:E0925, ledger:E1412</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3035C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB4D" flags="0x0">
    <title>Traction Control Gear Request - Hold Time, 1st Gear (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control gear request: time a 1st gear request is held before the request ends (stock 1 s). On this calibration the gear request is not applied to the shift schedule (inactive). Effect: no effect on this truck (raise = a 1st gear request lasts longer) Evidence: ledger:E0269, ledger:E0436, ledger:E0925, ledger:E1412</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3035E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB4E" flags="0x30">
    <title>Secondary Air Model - Step Weight vs Distance (DO NOT EDIT, dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight on each update step of the secondary air pressure model, by distance driven since the model last restarted its distance count. Stock 1.0 at 0 km falling to 0 at 16 km. Reference only: DO NOT EDIT. The secondary air system is not fitted on this truck (its enable is off in the stock calibration), so this has no effect on the stock calibration (dormant). Effect: reference only (secondary air diagnostic model) Evidence: ledger:E0623, ledger:E0624, ledger:E1415, ledger:E1454</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="4" />
      <LABEL index="3" value="6" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="12" />
      <LABEL index="7" value="14" />
      <LABEL index="8" value="16" />
      <LABEL index="9" value="18" />
      <LABEL index="10" value="20" />
      <LABEL index="11" value="22" />
      <LABEL index="12" value="24" />
      <LABEL index="13" value="26" />
      <LABEL index="14" value="28" />
      <LABEL index="15" value="30" />
      <LABEL index="16" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x326E8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB4F" flags="0x0">
    <title>Converter Model - Engine Speed Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new engine speed sample taken into the converter model&#x27;s filtered engine speed. Stock 0.75. Part of the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: lower = smoother but slower engine speed in the model Evidence: ledger:E1419</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB50" flags="0x0">
    <title>Converter Model - Capacity Torque Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter capacity factor added at low engine torque, fading to 0 across the torque band. Stock 0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (raise = model a looser converter at low torque) Evidence: ledger:E1419</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9DC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm/sqrt(Nm)</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB51" flags="0x0">
    <title>Converter Model - Upshift Ratio Offset Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new value taken into the offset between the model gear ratio and the estimated ratio, carried into the second phase of an upshift. Stock 0.50. Part of the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: lower = smoother hand over from the old gear ratio Evidence: ledger:E1420</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB52" flags="0x30">
    <title>Converter Model - Upshift Ratio Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. For the 1-2, 2-3 and 3-4 upshift: time after the shift starts during which the model keeps the old gear ratio before it follows the estimated ratio. Stock 0.1 s each. Part of the converter model, which estimates turbine speed and gear ratio for the transmission. Effect: raise = the model holds the old ratio longer into the shift Evidence: ledger:E1420</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>upshift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E9F0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB53" flags="0x30">
    <title>TCC Apply Start Offset - 1-2 Shift Index</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the converter clutch starts to apply, its pressure starts this much below the load based pressure, then the slip controller brings it up (never below zero pressure). By vehicle speed and engine torque, for the 1-2 shift index. Stock 0. Effect: raise = softer start of the apply (lower first pressure) Evidence: ledger:E1421</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3CE82" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>5</indexcount>
      <units>Nm (positive net engine torque)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="32" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="96" />
      <LABEL index="4" value="128" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="192" />
      <LABEL index="7" value="224" />
      <LABEL index="8" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CF08" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB54" flags="0x30">
    <title>TCC Apply Start Offset - Trans Fluid Temperature Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the apply start offset by transmission fluid temperature (stock 0). Effect: raise = softer apply start at that fluid temperature Evidence: ledger:E1421</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16.5" />
      <LABEL index="2" value="33" />
      <LABEL index="3" value="49.5" />
      <LABEL index="4" value="66" />
      <LABEL index="5" value="82.5" />
      <LABEL index="6" value="99" />
      <LABEL index="7" value="115.5" />
      <LABEL index="8" value="132" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D048" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB55" flags="0x0">
    <title>TCC Closed Throttle Release - Extra Hold, Base (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base extra hold time (stock 0 s). Closed throttle release extra hold: after a closed throttle release that began with the converter clutch applied, the clutch stays released for an extra hold time once the closed throttle condition ends; repeated releases within the repeat window add to the hold, and the hold decays over time. Every value is 0 on the stock calibration, so there is no extra hold (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1423, ledger:E1451</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D400" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB56" flags="0x0">
    <title>TCC Closed Throttle Release - Extra Hold Added per Repeat (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the extra hold for each repeated release inside the repeat window (stock 0 s). Closed throttle release extra hold: after a closed throttle release that began with the converter clutch applied, the clutch stays released for an extra hold time once the closed throttle condition ends; repeated releases within the repeat window add to the hold, and the hold decays over time. Every value is 0 on the stock calibration, so there is no extra hold (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1423, ledger:E1451</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D274" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB57" flags="0x0">
    <title>TCC Closed Throttle Release - Repeat Window (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A release within this time of the last one counts as a repeat (stock 0 s). Closed throttle release extra hold: after a closed throttle release that began with the converter clutch applied, the clutch stays released for an extra hold time once the closed throttle condition ends; repeated releases within the repeat window add to the hold, and the hold decays over time. Every value is 0 on the stock calibration, so there is no extra hold (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1423, ledger:E1451</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D276" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB58" flags="0x0">
    <title>TCC Closed Throttle Release - Extra Hold Decay Interval (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Every this long the accumulated extra hold is reduced by the decay step (stock 0 s). Closed throttle release extra hold: after a closed throttle release that began with the converter clutch applied, the clutch stays released for an extra hold time once the closed throttle condition ends; repeated releases within the repeat window add to the hold, and the hold decays over time. Every value is 0 on the stock calibration, so there is no extra hold (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1423, ledger:E1451</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C8AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB59" flags="0x0">
    <title>TCC Closed Throttle Release - Extra Hold Decay Step (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Taken off the accumulated extra hold every decay interval (stock 0 s). Closed throttle release extra hold: after a closed throttle release that began with the converter clutch applied, the clutch stays released for an extra hold time once the closed throttle condition ends; repeated releases within the repeat window add to the hold, and the hold decays over time. Every value is 0 on the stock calibration, so there is no extra hold (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1423, ledger:E1451</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C8AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB5A" flags="0x30">
    <title>TCC Slip Control - No Pressure Raise After Apply, by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. For this time after the converter clutch starts to apply, the slip controller does not raise clutch pressure even if slip is above target, by current gear (stock 0.8 s). Effect: raise = longer settling time before the controller adds pressure Evidence: ledger:E1424</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D19A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB5B" flags="0x30">
    <title>TCC Slip Control - Upshift Hold Time by Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During an upshift the slip controller is frozen for this time while slip is above the upshift hold threshold, by shift (1-2, 2-3, 3-4; stock 0 s). Effect: raise = the clutch pressure is held unchanged longer through an upshift Evidence: ledger:E1424</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3D194" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB5C" flags="0x0">
    <title>TCC Slip Control - Upshift Hold Slip Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During an upshift (and while the upshift hold time runs) the slip controller is frozen while slip is above this value (stock 0 rpm). Effect: raise = the controller keeps correcting through an upshift until slip exceeds this Evidence: ledger:E1424</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D18E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB5D" flags="0x0">
    <title>TCC Schedule Zone - Hold at Downshift Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The zone is not updated during this time after a downshift is commanded, with the shift torque band in its normal state (stock 0 s). The converter clutch logic keeps a schedule zone: below the release speed, between, or at or above the apply speed of the current clutch schedule; the closed throttle apply state and the low baro apply delay use it. Effect: raise = the clutch logic keeps the old zone longer at the start of a downshift Evidence: ledger:E1425</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D4A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB5E" flags="0x0">
    <title>TCC Schedule Zone - Hold at Downshift Start, Torque Band Active</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. As the downshift hold, used when the shift torque band is active (stock 0 s). The converter clutch logic keeps a schedule zone: below the release speed, between, or at or above the apply speed of the current clutch schedule; the closed throttle apply state and the low baro apply delay use it. Effect: raise = the clutch logic keeps the old zone longer at the start of a downshift Evidence: ledger:E1425</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D4A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB5F" flags="0x0">
    <title>TCC Low Baro Apply Delay - Baro On Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this barometric pressure the low baro apply delay is armed (stock 0 kPa). Low baro apply delay: in the released state at low barometric pressure (and not in transmission hot mode), once the apply speed is reached the clutch stays released for the delay time. The stock thresholds are 0 kPa, so this never happens (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1425</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D208" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB60" flags="0x0">
    <title>TCC Low Baro Apply Delay - Baro Off Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this barometric pressure the low baro apply delay is cleared (stock 0 kPa; between the two the last state holds). Low baro apply delay: in the released state at low barometric pressure (and not in transmission hot mode), once the apply speed is reached the clutch stays released for the delay time. The stock thresholds are 0 kPa, so this never happens (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1425</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D20A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB61" flags="0x0">
    <title>TCC Low Baro Apply Delay - Delay Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the clutch stays released after the apply speed is reached at low baro (stock 0 s). Low baro apply delay: in the released state at low barometric pressure (and not in transmission hot mode), once the apply speed is reached the clutch stays released for the delay time. The stock thresholds are 0 kPa, so this never happens (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1425</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D278" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB62" flags="0x0">
    <title>TCC Adapt - Confidence Gain per Update</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Each converter clutch learning update raises that torque cell&#x27;s learning confidence by this much, less the reduction for a large controller correction (stock 2.5 %). Higher confidence makes later learning steps smaller. Effect: raise = learning settles (slows down) after fewer updates Evidence: ledger:E1426</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CDA2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB63" flags="0x30">
    <title>TCC Adapt - Confidence Gain Reduction by Controller Correction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Subtracted from the confidence gain per update by the size of the slip controller pressure correction (stock 0 / 1 / 10 / 25 / 50 % at 0 / 32 / 64 / 96 / 128 kPa); confidence never falls. Effect: raise = large corrections build less confidence Evidence: ledger:E1426</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>kPa</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="32" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="96" />
      <LABEL index="4" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CDB2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB64" flags="0x30">
    <title>TCC Adapt - Learning Step Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the slip controller correction learned in one update, by the cell&#x27;s weight at the current torque and the cell&#x27;s learning confidence (stock 0 below 50 % weight; at full weight 99 % falling to 50 % as confidence builds). Effect: raise = faster learning Evidence: ledger:E1426</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>% confidence</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="12.5" />
      <LABEL index="2" value="25" />
      <LABEL index="3" value="37.5" />
      <LABEL index="4" value="50" />
      <LABEL index="5" value="62.5" />
      <LABEL index="6" value="75" />
      <LABEL index="7" value="87.5" />
      <LABEL index="8" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>% weight</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="25" />
      <LABEL index="2" value="50" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CDE8" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB65" flags="0x30">
    <title>TCC Apply Start Offset - Adder by Learning Confidence</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the apply start offset by the learning confidence at the current torque (stock 0). Effect: raise = softer apply start once learning has built confidence Evidence: ledger:E1426</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>% confidence</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="25" />
      <LABEL index="2" value="50" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CEC4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB66" flags="0x0">
    <title>VE Transient Mode - Window Exit Pressure Sum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While the transient mode is on, it ends when a full window has passed and the manifold pressure change from the window start, summed over the window&#x27;s updates, is below this (stock 1.5 kPa). Part of the window check of the volumetric efficiency transient mode, which runs only when its throttle gate is open; on the stock calibration that gate is closed, so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E1429</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB67" flags="0x0">
    <title>Engine Oil Pressure - Broadcast Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The engine oil pressure the PCM sends on the vehicle bus is a filtered copy of its oil pressure value (the estimate on stock, or the sensor reading with the sensor path on): each update moves it this fraction of the way to the new value. Stock 0.10. Effect: raise = the broadcast oil pressure follows changes faster Evidence: ledger:E1430, ledger:E1831</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x231B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB68" flags="0x0">
    <title>Crank and Cam Signal Loss Watchdog A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When no crank reference event has arrived for this long, the measured reference period is set to its maximum (engine speed from it reads zero) and the reference tracking is reset. Companion of Watchdog B. Stock 0.8 s. Effect: raise = a lost crank signal is noticed later Evidence: ledger:E1430</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x23A44" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB69" flags="0x0">
    <title>Ambient Air Temp Estimate - Run Time Before Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine run time, added up over the drives since the estimate was last reset, that must pass before the ambient air temperature estimate may rise toward the intake air temperature; until then it can only fall. It works together with the flush requirement after a hot soak. Stock 100 s. Effect: raise = the ambient estimate stays low for longer after a hot restart Evidence: ledger:E0385, ledger:E1184, ledger:E1334, ledger:E1431</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x34516" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB6A" flags="0x0">
    <title>3rd Upshift - Minimum Time Since the 1-2 Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. No 2-3 upshift until this long after the 1-2 shift was commanded (stock 0 s). Upshift minimum time in gear: when the shift schedule asks for that gear too soon, the transmission stays in the gear below until the time has passed. Effect: raise = holds 2nd longer after a 1-2 upshift Evidence: ledger:E1433</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DE0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB6B" flags="0x0">
    <title>4th Upshift - Minimum Time Since the 1-2 Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. No 3-4 upshift until this long after the 1-2 shift was commanded (stock 0 s). Upshift minimum time in gear: when the shift schedule asks for that gear too soon, the transmission stays in the gear below until the time has passed. Effect: raise = holds 3rd longer after pulling away Evidence: ledger:E1433</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DE2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB6C" flags="0x30">
    <title>Kickdown - Upshift Block Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a downshift requested with the pedal high, upshifts are blocked during the downshift and for this time after it, as long as the pedal stays high, by downshift (2-1, 3-2, 4-3; stock 0 s). Effect: raise = the transmission stays in the lower gear longer after a kickdown Evidence: ledger:E1433</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>downshift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2-1" />
      <LABEL index="1" value="3-2" />
      <LABEL index="2" value="4-3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39DC6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB6D" flags="0x0">
    <title>EVAP Test - Start-Up Coolant Minus Intake Air, Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest difference between start-up coolant and start-up intake air temperature (stock 6.7 C): the engine must have cooled down to near air temperature. Run condition of the engine-running EVAP test (large leak, purge flow and vent checks). Effect: raise = the test also runs after a shorter cool-down Evidence: ledger:E0769, ledger:E1072, ledger:E1434</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x356B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB6E" flags="0x0">
    <title>EVAP Test - Start-Up Coolant Window, Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest start-up coolant temperature for the test (stock 35 C). The same window applies to ambient air temperature for a related condition. Run condition of the engine-running EVAP test (large leak, purge flow and vent checks). Effect: raise = the test runs after warmer starts Evidence: ledger:E0769, ledger:E1072, ledger:E1434</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x356B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB6F" flags="0x0">
    <title>EVAP Test - Start-Up Coolant Window, Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest start-up coolant temperature for the test (stock 4.4 C). The same window applies to ambient air temperature for a related condition. Run condition of the engine-running EVAP test (large leak, purge flow and vent checks). Effect: lower = the test runs after colder starts Evidence: ledger:E0769, ledger:E1072, ledger:E1434</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x356B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB70" flags="0x0">
    <title>Tank Pressure Zero - Cold Soak Coolant Minus Intake Air, Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest start-up coolant minus intake air difference that counts as a cold soak (stock 8 C). The tank pressure zero check is only kept after a cold soak, with intake air below its maximum; otherwise it is cancelled. Effect: raise = more starts count as a cold soak (the zero check runs more often) Evidence: ledger:E0769, ledger:E1072, ledger:E1434</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x356AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB71" flags="0x0">
    <title>EVAP Test - Standstill Speed, Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed at or below which the engine-running EVAP test counts the vehicle as stopped (stock 5 km/h); above it the test&#x27;s standstill timer restarts. Effect: raise = the vehicle counts as stopped at a higher speed Evidence: ledger:E0769, ledger:E1435</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x356C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB72" flags="0x30">
    <title>Idle A/C - Clutch Handshake Airflow Adder vs Compressor Torque</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added at an A/C clutch release or engagement, by A/C compressor torque (0 to 80 Nm), per gear state and event. The value is multiplied by the A/C Idle Air rpm factor, 0.125 at every engine speed on stock; the scaling shown includes that factor (as for A/C Idle Air - Target). Stock 0 in every cell, so no adder is applied on the stock calibration. When the A/C compressor clutch releases or engages at idle, an extra idle airflow is added for the A/C idle adder hold time and then decays away. Effect: raise = more idle air...</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>event</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="In Gear, clutch release" />
      <LABEL index="1" value="In Gear, clutch engage" />
      <LABEL index="2" value="Park / Neutral, clutch release" />
      <LABEL index="3" value="Park / Neutral, clutch engage" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2910E" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>0</decimalpl>
      <min>-4.000000</min>
      <max>3.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB73" flags="0x30">
    <title>Idle A/C - Clutch Handshake Adder Decay Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After the hold time, the clutch handshake adder shrinks by this fraction of itself each update until it reaches zero. Stock 0.10 for both events; the adder itself is zero on the stock calibration, so this has no effect on the stock calibration (dormant). When the A/C compressor clutch releases or engages at idle, an extra idle airflow is added for the A/C idle adder hold time and then decays away. Effect: no effect on the stock calibration (raise = the adder fades faster) Evidence: ledger:E1436</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>event</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="A/C clutch release" />
      <LABEL index="1" value="A/C clutch engage" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2910A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB74" flags="0x30">
    <title>Downshift Adapt - Learn Cell Turbine Speeds (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turbine speed of each of the three learn cells (stock 1500 / 3000 / 4500 rpm). Axis data: keep ascending. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Its result is only used when its enable is set; stock the enable is off and every table is 0, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>learn cell</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39F28" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB75" flags="0x30">
    <title>Downshift Adapt - Desired Downshift Time vs Turbine Speed</title>
    <description>Change in small steps and log. Each row is [COUNT][TYPE][points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target time of the ratio change during a downshift, by turbine speed (columns) and gear index (rows). Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1700" />
      <LABEL index="4" value="2400" />
      <LABEL index="5" value="3100" />
      <LABEL index="6" value="3800" />
      <LABEL index="7" value="4500" />
      <LABEL index="8" value="5200" />
      <LABEL index="9" value="5900" />
      <LABEL index="10" value="6600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39F3C" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB76" flags="0x30">
    <title>Downshift Adapt - Pressure Step vs Time Error (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT][TYPE][points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learning step by how far the downshift time was from the desired time (columns, desired minus measured) and gear index (rows). Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Its result is only used when its enable is set; stock the enable is off and every table is 0, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="-0.20" />
      <LABEL index="3" value="-0.15" />
      <LABEL index="4" value="-0.10" />
      <LABEL index="5" value="-0.05" />
      <LABEL index="6" value="0.00" />
      <LABEL index="7" value="0.05" />
      <LABEL index="8" value="0.10" />
      <LABEL index="9" value="0.15" />
      <LABEL index="10" value="0.20" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39F5D" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>-256.000000</min>
      <max>254.000000</max>
      <MATH equation="X*2"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB77" flags="0x30">
    <title>Downshift Adapt - Step Share of the Lower Cell (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of a learning step given to the learn cell below the turbine speed, by where the speed lies between the two cells. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Its result is only used when its enable is set; stock the enable is off and every table is 0, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>position between cells</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.25" />
      <LABEL index="2" value="0.5" />
      <LABEL index="3" value="0.75" />
      <LABEL index="4" value="1.0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39F30" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>share</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>0.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB78" flags="0x30">
    <title>Downshift Adapt - Step Share of the Upper Cell (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of a learning step given to the learn cell above the turbine speed, by where the speed lies between the two cells. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Its result is only used when its enable is set; stock the enable is off and every table is 0, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>position between cells</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.25" />
      <LABEL index="2" value="0.5" />
      <LABEL index="3" value="0.75" />
      <LABEL index="4" value="1.0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39F37" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>share</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>0.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB79" flags="0x30">
    <title>Downshift Adapt - Fixed Step for Long Delays (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learning step used instead of the time error step when the downshift delay reached Long Delay Threshold. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Its result is only used when its enable is set; stock the enable is off and every table is 0, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39F88" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB7A" flags="0x30">
    <title>Downshift Adapt - Long Delay Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or above this downshift delay (command to start of the ratio change) the fixed step is used. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39FA8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB7B" flags="0x30">
    <title>Downshift Adapt - Min Downshift Delay (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A downshift is not used for learning when its delay is at or below this. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Its result is only used when its enable is set; stock the enable is off and every table is 0, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39FA2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB7C" flags="0x30">
    <title>Downshift Adapt - Min Downshift Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A downshift is not used for learning when its ratio change took this long or less. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Its result is only used when its enable is set; stock the enable is off and every table is 0, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39F90" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB7D" flags="0x30">
    <title>Downshift Adapt - Max Downshift Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A downshift is not used for learning when its ratio change took this long or more. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Its result is only used when its enable is set; stock the enable is off and every table is 0, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39F96" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB7E" flags="0x30">
    <title>Downshift Adapt - Min Time in Gear Before the Downshift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A downshift is not used for learning unless the previous gear was held at least this long. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39F9C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB7F" flags="0x30">
    <title>Downshift Adapt - Min Turbine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A downshift is not used for learning below this turbine speed. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39F16" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB80" flags="0x30">
    <title>Downshift Adapt - Max Turbine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A downshift is not used for learning above this turbine speed. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39F1C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB81" flags="0x0">
    <title>Downshift Adapt - Min Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. No learning below this transmission fluid temperature. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39F24" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB82" flags="0x0">
    <title>Downshift Adapt - Max Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. No learning above this transmission fluid temperature. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39F22" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB83" flags="0x0">
    <title>Downshift Adapt - Min Vehicle Acceleration</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. No learning while vehicle acceleration is below this. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39F7E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h per s</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB84" flags="0x0">
    <title>Downshift Adapt - Max Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. No learning above this throttle (stock 0: closed throttle downshifts only). Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39F82" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB85" flags="0x0">
    <title>Downshift Adapt - Learn Cell Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest value a learn cell can take. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Its result is only used when its enable is set; stock the enable is off and every table is 0, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39F84" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB86" flags="0x0">
    <title>Downshift Adapt - Learn Cell Maximum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest value a learn cell can take. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Its result is only used when its enable is set; stock the enable is off and every table is 0, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39F86" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB87" flags="0x0">
    <title>Downshift Adapt - Max Base Plus Learned Pressure (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A learn cell is limited so that the base pressure plus the cell does not exceed this. Part of the downshift adaptive pressure learning, which learns a correction to the downshift base pressure of the top gear low torque source from how long each downshift takes. Its result is only used when its enable is set; stock the enable is off and every table is 0, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0806, ledger:E1109, ledger:E1437</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39F80" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB88" flags="0x30">
    <title>Transmission Torque Loss vs Turbine Speed and Fluid Temp - 1st Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque the transmission loses in 1st gear, by turbine speed (rows) and fluid temperature (columns). Half of it is taken off the gearbox torque before it is multiplied up to the axle torque the road load estimate uses. Stock 0 everywhere: no loss is taken off. Effect: raise = a lower axle torque estimate for the road load estimate in that gear Evidence: ledger:E1439</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>degC (trans fluid)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>rpm (turbine)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="600" />
      <LABEL index="1" value="1800" />
      <LABEL index="2" value="3000" />
      <LABEL index="3" value="4200" />
      <LABEL index="4" value="5400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E252" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB89" flags="0x30">
    <title>Transmission Torque Loss vs Turbine Speed and Fluid Temp - 2nd Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque the transmission loses in 2nd gear, by turbine speed (rows) and fluid temperature (columns). Half of it is taken off the gearbox torque before it is multiplied up to the axle torque the road load estimate uses. Stock 0 everywhere: no loss is taken off. Effect: raise = a lower axle torque estimate for the road load estimate in that gear Evidence: ledger:E1439</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>degC (trans fluid)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>rpm (turbine)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="600" />
      <LABEL index="1" value="1800" />
      <LABEL index="2" value="3000" />
      <LABEL index="3" value="4200" />
      <LABEL index="4" value="5400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E288" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB8A" flags="0x30">
    <title>WOT Shift - Engine Speed Anticipation Time vs Trans Temp</title>
    <description>Change in small steps and log. Each row is [COUNT 17][TYPE 3][17 points]; COUNT and TYPE are structure bytes (TYPE sets the x32 scale), never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How far ahead the engine speed is predicted for the WOT upshift, by gear (1st, 2nd, 3rd) and transmission fluid temperature. Stock 1st gear 384 ms cold and 224 to 256 ms warm, 2nd gear 864 ms cold and 576 ms warm, 3rd gear 0. A learned correction is added on top. At wide open throttle the PCM predicts the engine speed a moment ahead (engine speed plus its rate of rise times this time) and compares that prediction with the WOT upshift rpm points, so the upshift starts early enough to land on the shift rpm....</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="-40" />
      <LABEL index="3" value="-28" />
      <LABEL index="4" value="-16" />
      <LABEL index="5" value="-4" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="20" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="44" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="68" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="92" />
      <LABEL index="14" value="104" />
      <LABEL index="15" value="116" />
      <LABEL index="16" value="128" />
      <LABEL index="17" value="140" />
      <LABEL index="18" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39E8C" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ms</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8160.000000</max>
      <MATH equation="X*32"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB8B" flags="0x30">
    <title>WOT Shift - Extra Anticipation Time in 1st Gear vs Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra anticipation time added in 1st gear, by a timer that restarts on a downshift into 1st and counts up in 1st gear (0 to 60 s). Stock 0 everywhere. At wide open throttle the PCM predicts the engine speed a moment ahead (engine speed plus its rate of rise times this time) and compares that prediction with the WOT upshift rpm points, so the upshift starts early enough to land on the shift rpm. Effect: raise = earlier WOT 1-2 upshift at that point of the timer Evidence: ledger:E1441</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="3.75" />
      <LABEL index="2" value="7.5" />
      <LABEL index="3" value="11.25" />
      <LABEL index="4" value="15" />
      <LABEL index="5" value="18.75" />
      <LABEL index="6" value="22.5" />
      <LABEL index="7" value="26.25" />
      <LABEL index="8" value="30" />
      <LABEL index="9" value="33.75" />
      <LABEL index="10" value="37.5" />
      <LABEL index="11" value="41.25" />
      <LABEL index="12" value="45" />
      <LABEL index="13" value="48.75" />
      <LABEL index="14" value="52.5" />
      <LABEL index="15" value="56.25" />
      <LABEL index="16" value="60" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39E6A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ms</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB8C" flags="0x0">
    <title>WOT Shift Engine Speed Tracker - Level Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 0.268. The WOT shift anticipation tracks engine speed with a level, a rate of rise and an acceleration, updated every 25 ms; each gain is the share of the difference between engine speed and the tracked level added to that state per update. At wide open throttle the PCM predicts the engine speed a moment ahead (engine speed plus its rate of rise times this time) and compares that prediction with the WOT upshift rpm points, so the upshift starts early enough to land on the shift rpm. Effect: raise = the tracked engine speed and its rate react faster but are noisier Evidence: ledger:E1441</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39ED4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB8D" flags="0x0">
    <title>WOT Shift Engine Speed Tracker - Rate Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 1.291. The WOT shift anticipation tracks engine speed with a level, a rate of rise and an acceleration, updated every 25 ms; each gain is the share of the difference between engine speed and the tracked level added to that state per update. At wide open throttle the PCM predicts the engine speed a moment ahead (engine speed plus its rate of rise times this time) and compares that prediction with the WOT upshift rpm points, so the upshift starts early enough to land on the shift rpm. Effect: raise = the tracked engine speed and its rate react faster but are noisier Evidence: ledger:E1441</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39ED6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB8E" flags="0x0">
    <title>WOT Shift Engine Speed Tracker - Acceleration Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 0.782. The WOT shift anticipation tracks engine speed with a level, a rate of rise and an acceleration, updated every 25 ms; each gain is the share of the difference between engine speed and the tracked level added to that state per update. At wide open throttle the PCM predicts the engine speed a moment ahead (engine speed plus its rate of rise times this time) and compares that prediction with the WOT upshift rpm points, so the upshift starts early enough to land on the shift rpm. Effect: raise = the tracked engine speed and its rate react faster but are noisier Evidence: ledger:E1441</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39ED8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB8F" flags="0x0">
    <title>Shift Engine Speed Predictor - Correction Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of the turbine speed error added to the predicted engine speed in each correction pass. Stock 0.25. During a shift the PCM can predict the engine speed the shift ends at: a first guess, then correction passes that compare the turbine speed the converter model expects at the predicted engine speed with the measured turbine speed. The prediction is only used by alternative torque calculations that are switched off on the stock calibration. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1444</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E3F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB90" flags="0x0">
    <title>TCC Release on Shift Request - Throttle Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While an upshift or downshift is requested, throttle above this releases the converter clutch. Stock 0 %. The converter clutch is then released gradually (ramped release). This only works in two TCC modes that the shift mode select on this calibration never uses. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1446</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D480" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB91" flags="0x0">
    <title>TCC Release on Shift Request - Throttle Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While an upshift or downshift is requested, throttle below this releases the converter clutch. Stock 0 %: never. The converter clutch is then released gradually (ramped release). This only works in two TCC modes that the shift mode select on this calibration never uses. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1446</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D482" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB92" flags="0x30">
    <title>Shift Solenoid Pattern by Gear State, Normal Set (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid on / off pattern for each gear state: bit 0 = solenoid A, bit 1 = solenoid B, bit 2 = third output. Stock 1st = A and B, 2nd = B, 3rd = none, 4th = A, other states 0. This set is used in normal operation. Structural: a wrong pattern selects the wrong gear. Effect: DO NOT EDIT: sets which shift solenoids are on in each gear Evidence: ledger:E1447, ledger:E1877</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>gear state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39EDA" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>bits</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB93" flags="0x30">
    <title>Shift Solenoid Pattern by Gear State, Override Set (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift solenoid on / off pattern for each gear state: bit 0 = solenoid A, bit 1 = solenoid B, bit 2 = third output. Stock 1st = A and B, 2nd = B, 3rd = none, 4th = A, other states 0. This set is used only while an external transmission override (a service tool output control request) selects it; normal driving uses the normal set. Structural: a wrong pattern selects the wrong gear. Effect: DO NOT EDIT: solenoid pattern used under an external transmission override Evidence: ledger:E1447, ledger:E1877</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>gear state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39EE1" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>bits</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB94" flags="0x0">
    <title>Axle Torque Smoothing - Previous Value Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of the previous smoothed axle torque. Stock 0.2. The axle torque estimate (gearbox torque less the transmission torque loss, times the gear and axle ratios) is smoothed before the road load estimate uses it: each update the smoothed value is the previous smoothed value times the previous value weight plus the new estimate times the new value weight. Effect: raise = slower, smoother response (and a larger settled value) Evidence: ledger:E1448</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E248" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB95" flags="0x0">
    <title>Axle Torque Smoothing - New Value Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of the new axle torque estimate. Stock 0.2 (with the stock previous value weight the smoothed value settles at a quarter of the estimate). The axle torque estimate (gearbox torque less the transmission torque loss, times the gear and axle ratios) is smoothed before the road load estimate uses it: each update the smoothed value is the previous smoothed value times the previous value weight plus the new estimate times the new value weight. Effect: raise = a larger smoothed value that follows the estimate faster Evidence: ledger:E1448</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E24A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB96" flags="0x0">
    <title>Axle Torque Smoothing - Road Load Lag Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How quickly the lagged copy of the smoothed axle torque used by the road load estimate follows it: the fraction of the difference taken per update. Stock 0.25. The axle torque estimate (gearbox torque less the transmission torque loss, times the gear and axle ratios) is smoothed before the road load estimate uses it: each update the smoothed value is the previous smoothed value times the previous value weight plus the new estimate times the new value weight. Effect: raise = the road load copy follows faster Evidence: ledger:E1448</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E24C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB97" flags="0x0">
    <title>Axle Torque - Slow Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of the change in the smoothed axle torque taken into its slow filtered copy each update. Stock 0.05. The slow copy is the drive force input of the road load model&#x27;s reserve share, which is switched off on this truck. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (raise = the slow copy follows the axle torque faster) Evidence: ledger:E1449</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E246" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB98" flags="0x30">
    <title>Attained Gear - Gear Ratio Window Top by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Top of the measured gear ratio window that counts as being in each gear. Stock 3.059 / 1.625 / 1.000 / 0.696. During the final phase of a shift the gear the transmission uses for its own calculations (shift index, transmission state, torque model) switches to the new gear once the measured gear ratio is inside this gear&#x27;s window; outside a shift it is always the commanded gear. Stock windows are the exact gear ratios, so in practice the switch happens when the shift ends. Effect: wider window (with the bottom) = the new gear is recognised earlier in a shift Evidence: ledger:E1450</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DEDA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB99" flags="0x30">
    <title>Attained Gear - Gear Ratio Window Bottom by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Bottom of the measured gear ratio window that counts as being in each gear. Stock 3.059 / 1.625 / 1.000 / 0.696. During the final phase of a shift the gear the transmission uses for its own calculations (shift index, transmission state, torque model) switches to the new gear once the measured gear ratio is inside this gear&#x27;s window; outside a shift it is always the commanded gear. Stock windows are the exact gear ratios, so in practice the switch happens when the shift ends. Effect: wider window (with the top) = the new gear is recognised earlier in a shift Evidence: ledger:E1450</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DEE2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB9A" flags="0x0">
    <title>EVAP Test - Purge Limit During Vent Check</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test: commanded evaporative purge is limited to this while the test holds the vent open for the vent restriction check (P0446) before its purge volume count starts, and in one later test state while the matching option word is set (set on stock). Stock 15 %. Effect: raise = more purge is allowed during those test steps Evidence: ledger:E0446, ledger:E0775, ledger:E0930, ledger:E1456</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3583E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB9B" flags="0x0">
    <title>Catalyst Temperature Model - Rich Cooling, Commanded EQ At or Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or above this commanded equivalence ratio the rich cooling factor applies to the cooling gain. Stock 1.00. When the modelled catalyst temperature is above its target it cools toward it at a rate set by airflow (the cooling gain). Effect: lower = the rich cooling factor applies at a leaner commanded mixture Evidence: ledger:E1459</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x21E50" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ ratio</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB9C" flags="0x0">
    <title>Catalyst Temperature Model - Rich Cooling Gain Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the cooling gain while the commanded equivalence ratio is at or above the rich threshold. Stock 1.00 (no change). When the modelled catalyst temperature is above its target it cools toward it at a rate set by airflow (the cooling gain). Effect: raise = the modelled catalyst temperature falls faster when running rich Evidence: ledger:E1459</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x21E52" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB9D" flags="0x0">
    <title>Manual Downshift Pressure Adder - Arming Window (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The adder is armed only if the low range is selected within this time of last driving in 3rd or 4th (stock 0 s). Manual downshift pressure adder (switched off on the stock calibration): when the selector is moved to a low range soon after driving in 3rd or 4th, the downshift into 2nd gets extra pressure by turbine speed, held until the gear ratio reaches the 2nd gear level and then ramped out. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1460</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3BC34" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB9E" flags="0x30">
    <title>Manual Downshift Pressure Adder - Pressure by Turbine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra downshift pressure by turbine speed (stock 0 kPa). Manual downshift pressure adder (switched off on the stock calibration): when the selector is moved to a low range soon after driving in 3rd or 4th, the downshift into 2nd gets extra pressure by turbine speed, held until the gear ratio reaches the 2nd gear level and then ramped out. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1460</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (turbine)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3BC3C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB9F" flags="0x30">
    <title>Manual Downshift Pressure Adder - Ramp-Out Start Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The adder starts ramping out once the gear ratio reaches this value, by turbine speed (stock 0). Manual downshift pressure adder (switched off on the stock calibration): when the selector is moved to a low range soon after driving in 3rd or 4th, the downshift into 2nd gets extra pressure by turbine speed, held until the gear ratio reaches the 2nd gear level and then ramped out. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1460</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (turbine)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3BC12" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBA0" flags="0x30">
    <title>Manual Downshift Pressure Adder - Turbine Speed Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turbine speed breakpoints of the ramp-out time (stock all 0). Axis data: keep ascending. Manual downshift pressure adder (switched off on the stock calibration): when the selector is moved to a low range soon after driving in 3rd or 4th, the downshift into 2nd gets extra pressure by turbine speed, held until the gear ratio reaches the 2nd gear level and then ramped out. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1460</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3BC60" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xBA1" flags="0x0">
    <title>Manual Downshift Pressure Adder - Ramp-Out Phase Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The adder ends once the ramp-out phase has lasted longer than this (stock 0 s). Manual downshift pressure adder (switched off on the stock calibration): when the selector is moved to a low range soon after driving in 3rd or 4th, the downshift into 2nd gets extra pressure by turbine speed, held until the gear ratio reaches the 2nd gear level and then ramped out. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1460</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3BC36" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBA2" flags="0x0">
    <title>Manual Range 3rd Hold - End Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this vehicle speed the hold ends (stock 500 km/h: the hold never applies). Manual range 3rd gear hold: after the selector is moved out of Drive while in 4th to a low range that would allow 2nd or 1st, a downshift to 3rd is kept in 3rd (no further downshift) while vehicle speed is high. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1463</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DD6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBA3" flags="0x0">
    <title>Manual Range 3rd Hold - Hold Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this vehicle speed 3rd is held; between the end speed and this, 3rd is held only while the hold time runs (stock 0 km/h). Manual range 3rd gear hold: after the selector is moved out of Drive while in 4th to a low range that would allow 2nd or 1st, a downshift to 3rd is kept in 3rd (no further downshift) while vehicle speed is high. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1463</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DD8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBA4" flags="0x0">
    <title>Manual Range 3rd Hold - Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time after leaving Drive during which 3rd is also held between the end speed and the hold speed (stock 0 s). Manual range 3rd gear hold: after the selector is moved out of Drive while in 4th to a low range that would allow 2nd or 1st, a downshift to 3rd is kept in 3rd (no further downshift) while vehicle speed is high. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1463</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DDE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBA5" flags="0x0">
    <title>Manual Range 3rd Hold - High Slip Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With converter slip above this the hold uses the high slip speed instead (stock 4096 rpm: never). Manual range 3rd gear hold: after the selector is moved out of Drive while in 4th to a low range that would allow 2nd or 1st, a downshift to 3rd is kept in 3rd (no further downshift) while vehicle speed is high. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1463</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DDC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xBA6" flags="0x30">
    <title>Throttle Torque Control - Engine Speed Term Gain vs RPM (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Gain applied to the engine speed term of the throttle torque controller&#x27;s input, by filtered engine speed (stock 0.60 up to 500 rpm rising to 0.96 at 8000 rpm). Part of the electronic throttle torque controller, which is switched off on this calibration: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0614, ledger:E1149, ledger:E1465</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="500" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1500" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2500" />
      <LABEL index="6" value="3000" />
      <LABEL index="7" value="3500" />
      <LABEL index="8" value="4000" />
      <LABEL index="9" value="4500" />
      <LABEL index="10" value="5000" />
      <LABEL index="11" value="5500" />
      <LABEL index="12" value="6000" />
      <LABEL index="13" value="6500" />
      <LABEL index="14" value="7000" />
      <LABEL index="15" value="7500" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21632" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xBA7" flags="0x0">
    <title>Throttle Torque Control - Engine Speed Filter Gain (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain for the engine speed the torque controller&#x27;s speed term uses (stock 0.9 per update). Part of the electronic throttle torque controller, which is switched off on this calibration: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0614, ledger:E1149, ledger:E1465</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2162C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBA8" flags="0x0">
    <title>Shift Torque Management - Park / Neutral Throttle Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In park or neutral with throttle below this (and always in reverse) the shift torque reduction does not run. Stock 100 %. Shift torque management: the transmission pulls engine torque during shifts by the shift torque reduction profiles. Effect: lower = the reduction can run in park / neutral above this throttle Evidence: ledger:E1467</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3ED58" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBA9" flags="0x0">
    <title>Shift Torque Management - Shift Start Delay Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. If the gear ratio has not started to change this long after the shift command, the shift torque reduction is dropped for that shift. Stock 2 s. Shift torque management: the transmission pulls engine torque during shifts by the shift torque reduction profiles. Effect: raise = slow-starting shifts keep their torque reduction Evidence: ledger:E1467</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3ED5A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xBAA" flags="0x30">
    <title>Shift Torque Management - Downshift Minimum Speed by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A downshift requested below this vehicle speed (by the gear the shift starts from, 1st to 3rd) gets no shift torque reduction. Stock 0 km/h (always allowed). Shift torque management: the transmission pulls engine torque during shifts by the shift torque reduction profiles. Effect: raise = slow downshifts run without torque reduction Evidence: ledger:E1467</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3ED5C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBAB" flags="0x30">
    <title>Upshift Request Torque Ramp - Shift Torque Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift torque points of the upshift request torque ramp curves. Stock all 0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1469</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F234" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>16383.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBAC" flags="0x30">
    <title>Upshift Request Torque Ramp - Target Reduction</title>
    <description>Change in small steps and log. Each row is a 1-D curve [COUNT = 9][9 points]; COUNT is a structure word, never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque reduction the upshift request ramp builds up to, by shift and shift torque. Stock all 0 %. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1469</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F246" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBAD" flags="0x30">
    <title>Upshift Request Torque Ramp - Ramp Rate</title>
    <description>Change in small steps and log. Each row is a 1-D curve [COUNT = 9][9 points]; COUNT is a structure word, never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the upshift request torque reduction builds up, by shift and shift torque. Stock all 0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1469</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F282" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%/s</units>
      <decimalpl>2</decimalpl>
      <min>-3125.000000</min>
      <max>3124.904633</max>
      <MATH equation="X/10.48576"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBAE" flags="0x30">
    <title>Shift Torque Profile - Target Reduction by Gear</title>
    <description>Change in small steps and log. Each row is a byte curve [COUNT = 17][TYPE][17 points]; header bytes are structure, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque reduction the shift torque profile ramps in and out, by commanded gear (rows 1st, 2nd, 3rd) and engine torque. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (raise = pull torque during the profiled shifts) Evidence: ledger:E1470</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="2" />
      <LABEL index="4" value="3" />
      <LABEL index="5" value="4" />
      <LABEL index="6" value="5" />
      <LABEL index="7" value="6" />
      <LABEL index="8" value="7" />
      <LABEL index="9" value="8" />
      <LABEL index="10" value="9" />
      <LABEL index="11" value="10" />
      <LABEL index="12" value="11" />
      <LABEL index="13" value="12" />
      <LABEL index="14" value="13" />
      <LABEL index="15" value="14" />
      <LABEL index="16" value="15" />
      <LABEL index="17" value="16" />
      <LABEL index="18" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3ED62" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>99.609375</max>
      <MATH equation="X/2.56"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xBAF" flags="0x0">
    <title>TCC Feed-Forward - Allowed Pressure Rise per Nm</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How much clutch pressure may rise per Nm of engine torque increase before the rising torque feed-forward pulls it back (stock 0.25 kPa per Nm). Part of the converter clutch slip controller&#x27;s feed-forward: while engine torque rises faster than the rise threshold, if clutch pressure is climbing faster than the allowed rise for that torque increase, the controller pulls the pressure back by the excess (times the rising gain). Effect: raise = more pressure rise allowed during a torque increase (firmer); lower = pressure held back more Evidence: ledger:E1471</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D186" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa/Nm</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xBB0" flags="0x30">
    <title>TCC Feed-Forward - Factor by Learning Confidence</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the rising torque feed-forward by the learning confidence at the current torque, this update and the last (stock 100 % everywhere). Part of the converter clutch slip controller&#x27;s feed-forward: while engine torque rises faster than the rise threshold, if clutch pressure is climbing faster than the allowed rise for that torque increase, the controller pulls the pressure back by the excess (times the rising gain). Effect: lower = weaker feed-forward pull back at that confidence Evidence: ledger:E1471</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>% confidence (now)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="25" />
      <LABEL index="2" value="50" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>% confidence (last update)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="25" />
      <LABEL index="2" value="50" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CED2" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xBB1" flags="0x0">
    <title>TCC Feed-Forward - Off Above Learning Confidence</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The rising torque feed-forward is skipped once the learning confidence at the current torque stays above this (stock 100 %: never skipped). Part of the converter clutch slip controller&#x27;s feed-forward: while engine torque rises faster than the rise threshold, if clutch pressure is climbing faster than the allowed rise for that torque increase, the controller pulls the pressure back by the excess (times the rising gain). Effect: lower = feed-forward stops once learning has settled Evidence: ledger:E1471</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D184" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xBB2" flags="0x30">
    <title>Line Pressure Learn - Slip Limit to Count Up (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter clutch slip error above which the learning count goes up, by engine torque. Part of the line pressure learning, which counts converter clutch slip events while the clutch is applied and, when the count reaches its limit, raises or lowers a learned line pressure for the gear. Stock the learned steps are 0, so the learned line pressure never changes: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0247, ledger:E0354, ledger:E1472</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>Nm (engine torque)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="64" />
      <LABEL index="2" value="128" />
      <LABEL index="3" value="192" />
      <LABEL index="4" value="256" />
      <LABEL index="5" value="320" />
      <LABEL index="6" value="384" />
      <LABEL index="7" value="448" />
      <LABEL index="8" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C626" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>-4096.000000</min>
      <max>4095.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBB3" flags="0x30">
    <title>Line Pressure Learn - Slip Limit to Count Down (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter clutch slip error below which the learning count goes down, by engine torque. Part of the line pressure learning, which counts converter clutch slip events while the clutch is applied and, when the count reaches its limit, raises or lowers a learned line pressure for the gear. Stock the learned steps are 0, so the learned line pressure never changes: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0247, ledger:E0354, ledger:E1472</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>Nm (engine torque)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="64" />
      <LABEL index="2" value="128" />
      <LABEL index="3" value="192" />
      <LABEL index="4" value="256" />
      <LABEL index="5" value="320" />
      <LABEL index="6" value="384" />
      <LABEL index="7" value="448" />
      <LABEL index="8" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C63A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>-4096.000000</min>
      <max>4095.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBB4" flags="0x30">
    <title>Line Pressure Learn - Count Added vs Slip (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Counts added per update while the slip is above the limit, by slip error (stock 1). Part of the line pressure learning, which counts converter clutch slip events while the clutch is applied and, when the count reaches its limit, raises or lowers a learned line pressure for the gear. Stock the learned steps are 0, so the learned line pressure never changes: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0247, ledger:E0354, ledger:E1472</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (clutch slip error)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="32" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="96" />
      <LABEL index="4" value="128" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="192" />
      <LABEL index="7" value="224" />
      <LABEL index="8" value="256" />
      <LABEL index="9" value="288" />
      <LABEL index="10" value="320" />
      <LABEL index="11" value="352" />
      <LABEL index="12" value="384" />
      <LABEL index="13" value="416" />
      <LABEL index="14" value="448" />
      <LABEL index="15" value="480" />
      <LABEL index="16" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C602" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>count</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBB5" flags="0x30">
    <title>Line Pressure Learn - Count Removed by Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Counts removed per update while the slip is below the limit, by gear and converter clutch state (stock 1). Part of the line pressure learning, which counts converter clutch slip events while the clutch is applied and, when the count reaches its limit, raises or lowers a learned line pressure for the gear. Stock the learned steps are 0, so the learned line pressure never changes: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0247, ledger:E0354, ledger:E1472</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>gear / converter clutch</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="1st, TCC on" />
      <LABEL index="2" value="2nd" />
      <LABEL index="3" value="2nd, TCC on" />
      <LABEL index="4" value="3rd" />
      <LABEL index="5" value="3rd, TCC on" />
      <LABEL index="6" value="4th" />
      <LABEL index="7" value="4th, TCC on" />
      <LABEL index="8" value="Reverse" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C7E6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>count</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xBB6" flags="0x0">
    <title>Line Pressure Learn - Min Converter Clutch Command (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The count only goes up while the converter clutch command is at least this fraction of the pressure a full command gives (stock 0). Part of the line pressure learning, which counts converter clutch slip events while the clutch is applied and, when the count reaches its limit, raises or lowers a learned line pressure for the gear. Stock the learned steps are 0, so the learned line pressure never changes: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0247, ledger:E0354, ledger:E1472</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C7E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xBB7" flags="0x30">
    <title>Line Pressure Learn - Step Up by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learned line pressure added when the count reaches its upper limit, by gear and converter clutch state (stock 0). Part of the line pressure learning, which counts converter clutch slip events while the clutch is applied and, when the count reaches its limit, raises or lowers a learned line pressure for the gear. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0247, ledger:E0354, ledger:E1472</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>gear / converter clutch</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="1st, TCC on" />
      <LABEL index="2" value="2nd" />
      <LABEL index="3" value="2nd, TCC on" />
      <LABEL index="4" value="3rd" />
      <LABEL index="5" value="3rd, TCC on" />
      <LABEL index="6" value="4th" />
      <LABEL index="7" value="4th, TCC on" />
      <LABEL index="8" value="Reverse" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C848" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBB8" flags="0x30">
    <title>Line Pressure Learn - Step Down by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learned line pressure removed when the count reaches its lower limit, by gear and converter clutch state (stock 0). Part of the line pressure learning, which counts converter clutch slip events while the clutch is applied and, when the count reaches its limit, raises or lowers a learned line pressure for the gear. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0247, ledger:E0354, ledger:E1472</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>gear / converter clutch</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="1st, TCC on" />
      <LABEL index="2" value="2nd" />
      <LABEL index="3" value="2nd, TCC on" />
      <LABEL index="4" value="3rd" />
      <LABEL index="5" value="3rd, TCC on" />
      <LABEL index="6" value="4th" />
      <LABEL index="7" value="4th, TCC on" />
      <LABEL index="8" value="Reverse" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C836" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBB9" flags="0x30">
    <title>Upshift Inhibit - Predictor Value Breakpoints (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Breakpoints of the predicted speed ratio curve, in the raw units of the Speed Ratio Curve output (stock 9920 to 28800). Shown as the raw stored value. Reference only: DO NOT EDIT. Part of the torque-based upshift inhibit: an upshift is held off when the torque predicted after it would be below what the truck needs now. Effect: reference only Evidence: ledger:E0345, ledger:E1473</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3915A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xBBA" flags="0x0">
    <title>TCC Re-Apply - Minimum Released Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once released, the converter clutch stays released at least this long before it may start to apply again (stock 2.5 s). Effect: raise = longer wait before the clutch re-applies after a release Evidence: ledger:E1474</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C8B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBBB" flags="0x0">
    <title>TAP Learn - Hold Off After TCC Apply</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Adaptive shift pressure (TAP) learning is held off while the converter clutch has been applied for less than this time; it is always held off while the clutch is ramping off (stock 0 s). Effect: raise = no shift learning just after the clutch applies Evidence: ledger:E1474</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C044" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBBC" flags="0x0">
    <title>Downshift Adapt - Hold Off After TCC Apply</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Downshift adaptive pressure learning is held off while the converter clutch has been applied for less than this time; it is always held off while the clutch is ramping off (stock 0 s). Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1474</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39F8E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBBD" flags="0x0">
    <title>TCC Downshift Block - Slip Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Slip limit of the downshift block (stock -4096 rpm, the lowest value: never). Downshift block with the converter clutch engaged: while a downshift is pending and the clutch is engaged with slip below the slip limit and throttle above the throttle limit, the current gear is held; the hold then lasts while the clutch state time is below the hold time. On the stock calibration the slip limit is the lowest possible value, so the block never engages (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1474</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DC0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBBE" flags="0x0">
    <title>TCC Downshift Block - Throttle Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle limit of the downshift block (stock 0 %). Downshift block with the converter clutch engaged: while a downshift is pending and the clutch is engaged with slip below the slip limit and throttle above the throttle limit, the current gear is held; the hold then lasts while the clutch state time is below the hold time. On the stock calibration the slip limit is the lowest possible value, so the block never engages (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1474</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DC2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBBF" flags="0x0">
    <title>TCC Downshift Block - Hold Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the downshift block may hold, measured as time in the current clutch state (stock 0 s). Downshift block with the converter clutch engaged: while a downshift is pending and the clutch is engaged with slip below the slip limit and throttle above the throttle limit, the current gear is held; the hold then lasts while the clutch state time is below the hold time. On the stock calibration the slip limit is the lowest possible value, so the block never engages (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1474</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBC0" flags="0x0">
    <title>2nd Gear Hold - Speed Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Speed limit of the 2nd gear hold (stock 26 km/h). 2nd gear hold: when the schedule asks for 1st while in 2nd, 2nd is kept at or above the speed limit, with throttle at or below the throttle limit, vehicle acceleration inside the acceleration window and the throttle not opening faster than the rate limit. Effect: raise = the hold applies only at higher speed Evidence: ledger:E1474</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DCC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBC1" flags="0x0">
    <title>2nd Gear Hold - Throttle Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle limit of the 2nd gear hold (stock 0 %: closed throttle only). 2nd gear hold: when the schedule asks for 1st while in 2nd, 2nd is kept at or above the speed limit, with throttle at or below the throttle limit, vehicle acceleration inside the acceleration window and the throttle not opening faster than the rate limit. Effect: raise = the hold also applies with some throttle Evidence: ledger:E1474</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DD4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBC2" flags="0x0">
    <title>2nd Gear Hold - Acceleration From</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower end of the acceleration window of the 2nd gear hold (stock 16 km/h per s; negative values are deceleration). 2nd gear hold: when the schedule asks for 1st while in 2nd, 2nd is kept at or above the speed limit, with throttle at or below the throttle limit, vehicle acceleration inside the acceleration window and the throttle not opening faster than the rate limit. Effect: lower = the hold also applies with less acceleration Evidence: ledger:E1474</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DCE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h/s</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBC3" flags="0x0">
    <title>2nd Gear Hold - Acceleration Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The vehicle acceleration must also be above this (stock 16 km/h per s). 2nd gear hold: when the schedule asks for 1st while in 2nd, 2nd is kept at or above the speed limit, with throttle at or below the throttle limit, vehicle acceleration inside the acceleration window and the throttle not opening faster than the rate limit. Effect: lower = the hold also applies with less acceleration Evidence: ledger:E1474</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DD0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h/s</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBC4" flags="0x0">
    <title>2nd Gear Hold - Throttle Opening Rate Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle opening rate limit of the 2nd gear hold; a closing throttle always passes (stock 0 %/s). 2nd gear hold: when the schedule asks for 1st while in 2nd, 2nd is kept at or above the speed limit, with throttle at or below the throttle limit, vehicle acceleration inside the acceleration window and the throttle not opening faster than the rate limit. Effect: raise = the hold also applies while the throttle is opening Evidence: ledger:E1474</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DD2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>%/s</units>
    <decimalpl>2</decimalpl>
    <min>-3200.000000</min>
    <max>3199.902344</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10.24"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBC5" flags="0x0">
    <title>Garage Shift - Max Engagement Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The garage engagement ends after this time (stock 2.5 s). Part of the garage shift (selector moved from park or neutral into a drive range or reverse), whose engagement runs in timed phases. Effect: raise = the garage pressure is held longer Evidence: ledger:E1169, ledger:E1187, ledger:E1237, ledger:E1475</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x37DC2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBC6" flags="0x0">
    <title>Garage Shift - End Above Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The garage engagement ends above this vehicle speed (stock 13 km/h). Part of the garage shift (selector moved from park or neutral into a drive range or reverse), whose engagement runs in timed phases. Effect: raise = the garage pressure can stay on to a higher speed Evidence: ledger:E1169, ledger:E1187, ledger:E1237, ledger:E1475</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x37DC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBC7" flags="0x0">
    <title>Garage Shift - Neutral Mode Below Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In range codes 5 and 7, below this speed the garage control uses its neutral mode (stock 13 km/h). Part of the garage shift (selector moved from park or neutral into a drive range or reverse), whose engagement runs in timed phases. Effect: raise = neutral mode up to a higher speed Evidence: ledger:E1169, ledger:E1187, ledger:E1237, ledger:E1475</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x37E26" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBC8" flags="0x0">
    <title>Garage Shift - Clutch Slip to Arm the Engaged Check</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Clutch slip at or above which the engaged check arms (stock 100 rpm). Part of the garage shift (selector moved from park or neutral into a drive range or reverse), whose engagement runs in timed phases. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1169, ledger:E1187, ledger:E1237, ledger:E1475</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x37F3C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBC9" flags="0x0">
    <title>Garage Shift - Clutch Slip Engaged</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once armed, clutch slip at or below this ends the garage engagement (stock 200 rpm). Part of the garage shift (selector moved from park or neutral into a drive range or reverse), whose engagement runs in timed phases. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1169, ledger:E1187, ledger:E1237, ledger:E1475</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x37F3E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBCA" flags="0x0">
    <title>Garage Shift - Phase 3 Start, Input Speed Rate (Type A)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the type A engagements (into drive or reverse), the second phase ends and the third starts when the input speed falls faster than this (stock 0 rpm/s: as soon as the input speed starts to fall). Part of the garage shift (selector moved from park or neutral into a drive range or reverse), whose engagement runs in timed phases. Effect: raise = the third phase starts earlier Evidence: ledger:E1169, ledger:E1187, ledger:E1237, ledger:E1475</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x37F40" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm/s</units>
    <decimalpl>1</decimalpl>
    <min>-8000.000000</min>
    <max>7999.755859</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4.096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBCB" flags="0x0">
    <title>Garage Shift - Phase 3 Arm, Input Speed Rate Rise (Type B)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the type B engagements, the input speed must first rise faster than this (stock 0 rpm/s) before the third phase can start. Part of the garage shift (selector moved from park or neutral into a drive range or reverse), whose engagement runs in timed phases. Effect: raise = a stronger input speed rise is needed Evidence: ledger:E1169, ledger:E1187, ledger:E1237, ledger:E1475</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38114" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm/s</units>
    <decimalpl>1</decimalpl>
    <min>-8000.000000</min>
    <max>7999.755859</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4.096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBCC" flags="0x0">
    <title>Garage Shift - Phase 3 Start, Input Speed Rate Fall (Type B)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the type B engagements, after the rise the third phase starts when the input speed rate drops below this (stock 0 rpm/s). Part of the garage shift (selector moved from park or neutral into a drive range or reverse), whose engagement runs in timed phases. Effect: raise = the third phase starts earlier Evidence: ledger:E1169, ledger:E1187, ledger:E1237, ledger:E1475</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38116" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm/s</units>
    <decimalpl>1</decimalpl>
    <min>-8000.000000</min>
    <max>7999.755859</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4.096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBCD" flags="0x0">
    <title>Corrected Coolant - Cold Correction Off Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The corrected coolant temperature the PCM uses for its coolant model, oil life, torque friction and other functions equals the measured coolant above this temperature. At or below it, it is pulled toward the intake air temperature (see Corrected Coolant - Pull Toward Intake Air). Stock 75 C. Effect: raise = the cold correction applies up to a warmer coolant temperature Evidence: ledger:E1477</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x23990" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBCE" flags="0x0">
    <title>Corrected Coolant - Pull Toward Intake Air</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or below the cold correction temperature, the corrected coolant temperature is the measured coolant minus this share of (coolant - intake air temperature), only when the intake air is colder. Stock 0.62. Effect: raise = the corrected coolant reads closer to the intake air temperature on a cold engine Evidence: ledger:E1477</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x23992" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBCF" flags="0x0">
    <title>Shift Engine Speed Predictor - Correction Passes</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of correction passes after the first guess (0 = the first guess is used). Stock 1. During a shift the PCM can predict the engine speed the shift ends at: a first guess from turbine speed and the speed ratio shifted by this step, then a number of correction passes. The prediction is only used by alternative torque calculations that are switched off on the stock calibration. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1479</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E3EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBD0" flags="0x0">
    <title>Shift Engine Speed Predictor - Speed Ratio Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Speed ratio step for the first guess: taken off the current turbine to engine speed ratio for an upshift, added otherwise. Stock 0.25. During a shift the PCM can predict the engine speed the shift ends at: a first guess from turbine speed and the speed ratio shifted by this step, then a number of correction passes. The prediction is only used by alternative torque calculations that are switched off on the stock calibration. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1479</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E3EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBD1" flags="0x0">
    <title>Input Speed - Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new computed transmission input speed taken into the filtered input speed. Stock 1.0 (no smoothing). Effect: lower = smoother but slower filtered input speed Evidence: ledger:E1480</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEF0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBD2" flags="0x0">
    <title>Input Speed Rate Tracker - Speed Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How strongly the input speed tracker corrects its speed estimate toward the measured input speed each 25 ms. Stock 0.268. The tracked input speed rate is used by the garage shift (engagement) control and the idle airflow follower. Effect: raise = the tracked speed follows faster Evidence: ledger:E1480</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEF2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBD3" flags="0x0">
    <title>Input Speed Rate Tracker - Rate Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How strongly the input speed tracker corrects its rate (rpm per second) from the speed error each 25 ms. Stock 1.291. The tracked input speed rate is used by the garage shift (engagement) control and the idle airflow follower. Effect: raise = the tracked rate reacts faster but is noisier Evidence: ledger:E1480</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEF4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBD4" flags="0x0">
    <title>Input Speed Rate Tracker - Acceleration Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How strongly the input speed tracker corrects its rate of change of the rate from the speed error each 25 ms. Stock 0.782. The tracked input speed rate is used by the garage shift (engagement) control and the idle airflow follower. Effect: raise = the tracked rate catches ramps faster Evidence: ledger:E1480</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DEF6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBD5" flags="0x0">
    <title>TCC Adapt - Max Learned Line Pressure Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converter clutch adaptive learning holds off while the learned line pressure offset of the current range is at or above this (stock 275 kPa). Effect: lower = clutch learning stops earlier as line pressure learning grows Evidence: ledger:E1483</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3CD84" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBD6" flags="0x0">
    <title>TCC PWM Solenoid Frequency</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Switching frequency of the converter clutch PWM solenoid (stock 32 Hz). Effect: change only to match a different solenoid; affects how the clutch pressure is delivered Evidence: ledger:E1483</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DCB6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Hz</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>16383.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBD7" flags="0x0">
    <title>TCC Release in Hot Mode - Fluid Above, On (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission fluid temperature above which the hot mode converter clutch release starts. Stock 0 C. In transmission hot mode, once the fluid is above the on temperature the converter clutch is released (gradually from applied, held released otherwise) until the fluid falls below the off temperature. Switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1484</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D488" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBD8" flags="0x0">
    <title>TCC Release in Hot Mode - Fluid Below, Off (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission fluid temperature below which the hot mode converter clutch release ends (between the two the last state holds). Stock 0 C. In transmission hot mode, once the fluid is above the on temperature the converter clutch is released (gradually from applied, held released otherwise) until the fluid falls below the off temperature. Switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1484</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D486" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBD9" flags="0x0">
    <title>Road Load Model - Aerodynamic Drag Area</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Drag area (drag coefficient times frontal area) for the model&#x27;s air resistance, corrected for air pressure and intake air temperature. Stock 0. Part of the road load model the shift sequencing uses to estimate grade and road load. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1485</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>m^2</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.719564</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/17619"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBDA" flags="0x0">
    <title>Road Load Model - Grade Force Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new grade force estimate taken into the filtered grade force. Stock 0. Part of the road load model the shift sequencing uses to estimate grade and road load. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1485</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBDB" flags="0x0">
    <title>Road Load Model - Grade Estimate Minimum Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The grade force is estimated only above this vehicle speed; at or below it the filtered grade force is cleared. Stock 0. Part of the road load model the shift sequencing uses to estimate grade and road load. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1485</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBDC" flags="0x0">
    <title>Road Load Model - Rolling Radius</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Effective tyre rolling radius that turns axle torque into drive force. Also the starting value of the learned radius. Stock 0. Part of the road load model the shift sequencing uses to estimate grade and road load. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1485</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>m</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBDD" flags="0x0">
    <title>Road Load Model - Initial Road Load (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Road load force the model starts from at power up. Stock 0. Part of the road load model the shift sequencing uses to estimate grade and road load. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1485</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2D4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>N</units>
    <decimalpl>0</decimalpl>
    <min>-32768.000000</min>
    <max>32767.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBDE" flags="0x0">
    <title>Road Load Model - Road Load and Radius Learn Minimum Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The road load estimate and the rolling radius learn run only above this vehicle speed. Stock 0. Part of the road load model the shift sequencing uses to estimate grade and road load. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1485</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2D6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBDF" flags="0x0">
    <title>Road Load Model - Road Load Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new road load force (drive force less mass times acceleration) taken into the filtered road load. Stock 0. Part of the road load model the shift sequencing uses to estimate grade and road load. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1485</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2D8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBE0" flags="0x0">
    <title>Road Load Model - Road Load Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower limit of the filtered road load force. Stock 0. Part of the road load model the shift sequencing uses to estimate grade and road load. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1485</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2DA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>N</units>
    <decimalpl>0</decimalpl>
    <min>-32768.000000</min>
    <max>32767.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBE1" flags="0x0">
    <title>Road Load Model - Road Load Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit of the filtered road load force. Stock 0. Part of the road load model the shift sequencing uses to estimate grade and road load. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1485</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2DC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>N</units>
    <decimalpl>0</decimalpl>
    <min>-32768.000000</min>
    <max>32767.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBE2" flags="0x0">
    <title>Road Load Model - Rolling Resistance Coefficient</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rolling resistance coefficient; rolling resistance force = coefficient x vehicle mass x g. Stock 0. Part of the road load model the shift sequencing uses to estimate grade and road load. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1485</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2DE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>coefficient</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBE3" flags="0x0">
    <title>Road Load Model - Rolling Radius Learn Maximum Speed Mismatch</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The radius learns only while wheel speed and transmission output speed differ by less than this; otherwise the learned radius returns to the calibrated radius. Stock 0. Part of the road load model the shift sequencing uses to estimate grade and road load. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1485</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBE4" flags="0x0">
    <title>Road Load Model - Expected Force Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new expected force value taken into the filtered expected force. Stock 0. Part of the road load model the shift sequencing uses to estimate grade and road load. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1486</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F3A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xBE5" flags="0x30">
    <title>Road Load Model - Expected Acceleration vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle acceleration the model expects at each speed. Expected force = vehicle mass x this acceleration, less air and rolling resistance. Stock all 0. Part of the road load model the shift sequencing uses to estimate grade and road load. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1486</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>vehicle speed (km/h)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F3A8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>m/s^2</units>
      <decimalpl>3</decimalpl>
      <min>-64.000000</min>
      <max>63.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBE6" flags="0x30">
    <title>Road Load Model - Gear Force Factor vs Coolant Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier on the gear force (table below) by engine coolant temperature (1.0 = as calibrated). Stock all 0. Part of the road load model the shift sequencing uses to estimate grade and road load. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1486</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>coolant temperature (C)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-28" />
      <LABEL index="1" value="-8" />
      <LABEL index="2" value="12" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="52" />
      <LABEL index="5" value="72" />
      <LABEL index="6" value="92" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="132" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F3BC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBE7" flags="0x30">
    <title>Road Load Model - Gear Force by Gear and Speed</title>
    <description>Change in small steps and log. Each row is a 1-D curve [COUNT = 9][9 points]; COUNT is a structure word, never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Force by gear and vehicle speed, scaled by the coolant factor. The shift sequencing compares the expected force less this force with the available force; during a shift, this force for the current gear also caps the drive force taken from axle torque. Stock all 0. Part of the road load model the shift sequencing uses to estimate grade and road load. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1486</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F3D4" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>N</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xBE8" flags="0x0">
    <title>Mass Estimator - Reference Point Refresh Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time without an accepted step after which the estimator takes a new reference point. Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBE9" flags="0x0">
    <title>Mass Estimator - Maximum Wheel Speed Difference</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Estimation pauses while the two wheel speeds differ by this share of vehicle speed or more (cornering). Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>799.987793</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/81.92"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBEA" flags="0x0">
    <title>Mass Estimator - Estimate Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Mass estimates at or below this are not learned. Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kg</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBEB" flags="0x0">
    <title>Mass Estimator - Estimate Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Mass estimates at or above this are not learned. Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kg</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBEC" flags="0x0">
    <title>Mass Estimator - Stable Conditions Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the entry conditions must hold before a point is used. Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBED" flags="0x0">
    <title>Mass Estimator - Learns Using the First Weight Curve</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of learns that use the first learn weight curve; later learns use the weight table. Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2F8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBEE" flags="0x0">
    <title>Mass Estimator - Maximum Grade Change Between Estimates</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A new estimate is learned only if the road grade it implies differs from the previous one by less than this. Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2FA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBEF" flags="0x0">
    <title>Mass Estimator - Maximum Change Between Estimates</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A new estimate is learned only if it differs from the previous estimate by less than this. Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kg</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xBF0" flags="0x30">
    <title>Mass Estimator - Minimum Acceleration Step by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A point is used only if vehicle acceleration differs from the reference point by more than this. Stock all 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F300" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>m/s^2</units>
      <decimalpl>3</decimalpl>
      <min>-64.000000</min>
      <max>63.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBF1" flags="0x30">
    <title>Mass Estimator - Minimum Wheel Torque Step by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A point is used only if wheel torque differs from the reference point by more than this. Stock all 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F308" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>32767.500000</max>
      <MATH equation="X/2"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBF2" flags="0x30">
    <title>Mass Estimator - Learn Weight vs Torque Step, First Learns</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new mass estimate taken into the learned mass, by wheel torque step, for the first learns. Stock all 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>wheel torque step (Nm)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-9600" />
      <LABEL index="1" value="-7200" />
      <LABEL index="2" value="-4800" />
      <LABEL index="3" value="-2400" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="4800" />
      <LABEL index="7" value="7200" />
      <LABEL index="8" value="9600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F312" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>weight</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBF3" flags="0x30">
    <title>Mass Estimator - Learn Weight vs Torque Step and Sample Age</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new mass estimate taken into the learned mass, by wheel torque step and the time since the previous reference point, for later learns. Stock all 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487, ledger:E1565</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>wheel torque step (Nm)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-9600" />
      <LABEL index="1" value="-7200" />
      <LABEL index="2" value="-4800" />
      <LABEL index="3" value="-2400" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="4800" />
      <LABEL index="7" value="7200" />
      <LABEL index="8" value="9600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>time since reference (s)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="2.5" />
      <LABEL index="2" value="5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="10" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F328" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>weight</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBF4" flags="0x30">
    <title>Mass Estimator - Minimum Speed vs Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Estimation runs only above this vehicle speed. Below it a timer runs that resets the learn count. Stock all 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>throttle (%)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="12.5" />
      <LABEL index="2" value="25" />
      <LABEL index="3" value="37.5" />
      <LABEL index="4" value="50" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F384" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBF5" flags="0x30">
    <title>Mass Estimator - Maximum Speed vs Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Estimation runs only below this vehicle speed. Stock all 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>throttle (%)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="12.5" />
      <LABEL index="2" value="25" />
      <LABEL index="3" value="37.5" />
      <LABEL index="4" value="50" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F390" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xBF6" flags="0x0">
    <title>Mass Estimator - Minimum Drive Force</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Estimation runs only with drive force above this. Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F39A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>N</units>
    <decimalpl>0</decimalpl>
    <min>-32768.000000</min>
    <max>32767.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBF7" flags="0x0">
    <title>Mass Estimator - Maximum Drive Force</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Estimation runs only with drive force below this. Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F39C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>N</units>
    <decimalpl>0</decimalpl>
    <min>-32768.000000</min>
    <max>32767.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBF8" flags="0x0">
    <title>Mass Estimator - Learned Mass Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower limit of the learned vehicle mass. Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F39E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kg</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBF9" flags="0x0">
    <title>Mass Estimator - Learned Mass Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit of the learned vehicle mass. Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F3A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kg</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBFA" flags="0x0">
    <title>Road Load Model - Wheel Speed Difference Filter Weight (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new wheel speed difference (as a share of vehicle speed) taken into the filtered value the mass estimator checks; 0 = no smoothing. Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1487</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F424" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xBFB" flags="0x30">
    <title>Top Gear Coast Downshift Torque Request - Minimum Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The request can trigger only with engine speed above this, by gear. Used only for downshifts from top gear at low engine torque. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1489</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EB06" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBFC" flags="0x30">
    <title>Top Gear Coast Downshift Torque Request - Ratio Window Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The request triggers when the measured gear ratio is below the cap and outside the window from this value to the high value, by gear. Used only for downshifts from top gear at low engine torque. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1489</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EB0E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBFD" flags="0x30">
    <title>Top Gear Coast Downshift Torque Request - Ratio Window High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper end of the measured gear ratio window (see Ratio Window Low), by gear. Used only for downshifts from top gear at low engine torque. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1489</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EB16" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBFE" flags="0x30">
    <title>Top Gear Coast Downshift Torque Request - Ratio Cap</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The request triggers only with the measured gear ratio below this, and ends once the ratio has stayed above it for the release time, by gear. Used only for downshifts from top gear at low engine torque. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1489</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EB1E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xBFF" flags="0x30">
    <title>Top Gear Coast Downshift Torque Request - Release Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the measured gear ratio must stay above the cap before the request ends, by gear. Used only for downshifts from top gear at low engine torque. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1489</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EB26" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>1.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC00" flags="0x30">
    <title>Top Gear Coast Downshift Torque Request - Delay Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time from the trigger until the torque request is sent, by gear. Used only for downshifts from top gear at low engine torque. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1489</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EB2A" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>1.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC01" flags="0x30">
    <title>Top Gear Coast Downshift Torque Request - Engine Torque Request</title>
    <description>Change in small steps and log. Each row is a 1-D curve [COUNT = 17][17 points]; COUNT is a structure word, never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque the transmission requests from the engine controller while the trigger is active, by gear and turbine speed (lowest priority of the transmission torque requests). Used only for downshifts from top gear at low engine torque. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1489</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EB2E" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xC02" flags="0x0">
    <title>Start Phase Length</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. For this long after the engine starts, the transmission keeps re-checking its start conditions (intake air temperature class used by the normal shift modes, cold soak checks); after it the results are held until the next start. Stock 30 s. Effect: raise = the start conditions are re-checked for longer after start Evidence: ledger:E1490</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F7D6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC03" flags="0x0">
    <title>Acceleration Torque Limit - Arm Acceleration (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the basic mode the limit arms when vehicle acceleration is above this (with throttle and speed above their entry values). Part of the acceleration torque limit, which is switched off on this truck (master switch off), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1493</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3FEBA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h/s</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC04" flags="0x0">
    <title>Acceleration Torque Limit - Arm Acceleration, Wheel Speed Modes (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the wheel speed modes the limit arms only with vehicle acceleration above this. Part of the acceleration torque limit, which is switched off on this truck (master switch off), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1493</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3FEBC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h/s</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC05" flags="0x0">
    <title>Acceleration Torque Limit - Exit Throttle (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The active limit ends when throttle drops to this or below. Part of the acceleration torque limit, which is switched off on this truck (master switch off), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1493</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3FEBE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC06" flags="0x0">
    <title>Acceleration Torque Limit - Entry Throttle (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The limit can arm only with throttle above this. Part of the acceleration torque limit, which is switched off on this truck (master switch off), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1493</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3FEC0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC07" flags="0x0">
    <title>Acceleration Torque Limit - Maximum Active Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The active limit ends after this long. Part of the acceleration torque limit, which is switched off on this truck (master switch off), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1493</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3FEC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC08" flags="0x0">
    <title>Acceleration Torque Limit - Exit Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The active limit ends when vehicle speed drops to this or below. Part of the acceleration torque limit, which is switched off on this truck (master switch off), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1493</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3FECE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC09" flags="0x0">
    <title>Acceleration Torque Limit - Entry Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The limit can arm only with vehicle speed above this. Part of the acceleration torque limit, which is switched off on this truck (master switch off), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1493</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3FED0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC0A" flags="0x0">
    <title>Acceleration Torque Limit - Maximum Non-Driven Wheel Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In two of the wheel speed modes the limit arms only with the non-driven wheel speed below this. Part of the acceleration torque limit, which is switched off on this truck (master switch off), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1493</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3FED2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC0B" flags="0x0">
    <title>Road Load Model - Grade Estimate Hold After Brake Release (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While the brake switch is on, and for this long after it turns off, the road load model estimates road grade; otherwise it estimates road load. Stock 0 s. Part of the road load model the shift sequencing uses to estimate grade and road load. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1494</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC0C" flags="0x0">
    <title>Acceleration Torque Limit - Other Axle Compensation (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the wheel difference mode the measured left / right wheel speed difference is reduced by this share of the other axle&#x27;s left / right difference (cornering compensation). Part of the acceleration torque limit, which is switched off on this truck (master switch off), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1495</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3FEC2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC0D" flags="0x0">
    <title>Acceleration Torque Limit - Slip to Stay Active (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the slip modes the active limit stays on while output speed exceeds the non-driven wheel speed by at least this. In the single wheel slip mode the measured difference is doubled before the compare. Part of the acceleration torque limit, which is switched off on this truck (master switch off), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1495</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3FEC6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC0E" flags="0x0">
    <title>Acceleration Torque Limit - Slip to Arm (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the slip modes the limit arms when output speed exceeds the non-driven wheel speed by at least this. In the single wheel slip mode the measured difference is doubled before the compare. Part of the acceleration torque limit, which is switched off on this truck (master switch off), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1495</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3FEC8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC0F" flags="0x0">
    <title>Acceleration Torque Limit - Wheel Difference to Stay Active (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the wheel difference mode the active limit stays on while the compensated left / right wheel speed difference is at least this. Part of the acceleration torque limit, which is switched off on this truck (master switch off), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1495</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3FECA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC10" flags="0x0">
    <title>Acceleration Torque Limit - Wheel Difference to Arm (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the wheel difference mode the limit arms when the compensated left / right wheel speed difference is at least this. Part of the acceleration torque limit, which is switched off on this truck (master switch off), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1495</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3FECC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xC11" flags="0x30">
    <title>Acceleration Torque Limit - Engine Torque Request vs Wheel Speed Difference</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque requested while the limit is active in the wheel speed modes. Axis: the left / right wheel speed difference (0 to 128 km/h); in the single wheel slip mode the axis is twice the wheel to output speed difference, so it spans 0 to 64 km/h of that difference. Stock 25 Nm everywhere. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1495</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>wheel speed difference (km/h)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="8" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="24" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="48" />
      <LABEL index="7" value="56" />
      <LABEL index="8" value="64" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="88" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="104" />
      <LABEL index="14" value="112" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EBC0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC12" flags="0x30">
    <title>Road Load Model - Available Force vs Speed by Gear (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 9][9 words]; COUNT is a structure word. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Force the truck can deliver in each gear (rows) by speed (columns). The road load share is the road load minus the gear force (Road Load Model - Gear Force by Gear and Speed) divided by this. Part of the road load model, which compares the road load with the force available in each gear to decide when to hold the transmission out of top gear (for example on grades or with a heavy load). The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1496</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="48" />
      <LABEL index="5" value="64" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="96" />
      <LABEL index="8" value="112" />
      <LABEL index="9" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x387D4" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>N</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xC13" flags="0x0">
    <title>Road Load Model - Load Share Filter Gain, Fast Rise (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain of the road load share when it rises by more than the Fast Rise Step. Part of the road load model, which compares the road load with the force available in each gear to decide when to hold the transmission out of top gear (for example on grades or with a heavy load). The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1496</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3844A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC14" flags="0x0">
    <title>Road Load Model - Load Share Filter Gain, Other Changes (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain of the road load share for smaller rises and for every fall. Part of the road load model, which compares the road load with the force available in each gear to decide when to hold the transmission out of top gear (for example on grades or with a heavy load). The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1496</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3844C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC15" flags="0x0">
    <title>Road Load Model - Load Share Fast Rise Step (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A rise of the road load share larger than this uses the fast rise filter gain. Part of the road load model, which compares the road load with the force available in each gear to decide when to hold the transmission out of top gear (for example on grades or with a heavy load). The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1496</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38472" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xC16" flags="0x30">
    <title>Road Load Model - Available Force for Reserve Share by Gear (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 9][9 words]; COUNT is a structure word. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Force against which the reserve share is taken, by gear (rows) and speed (columns). The reserve share is the present drive force (limited by the gear force during a shift) minus the road load, divided by this. Part of the road load model, which compares the road load with the force available in each gear to decide when to hold the transmission out of top gear (for example on grades or with a heavy load). The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1497</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="48" />
      <LABEL index="5" value="64" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="96" />
      <LABEL index="8" value="112" />
      <LABEL index="9" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38784" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>N</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xC17" flags="0x0">
    <title>Road Load Model - Reserve Share Filter Gain, Fast Rise (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain of the reserve share when it rises by more than the Reserve Fast Rise Step. Part of the road load model, which compares the road load with the force available in each gear to decide when to hold the transmission out of top gear (for example on grades or with a heavy load). The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1497</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3844E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC18" flags="0x0">
    <title>Road Load Model - Reserve Share Filter Gain, Other Changes (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain of the reserve share for smaller rises and for every fall. Part of the road load model, which compares the road load with the force available in each gear to decide when to hold the transmission out of top gear (for example on grades or with a heavy load). The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1497</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38450" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC19" flags="0x0">
    <title>Road Load Model - Reserve Fast Rise Step (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A rise of the reserve share larger than this uses the fast rise filter gain. Part of the road load model, which compares the road load with the force available in each gear to decide when to hold the transmission out of top gear (for example on grades or with a heavy load). The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1497</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38474" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC1A" flags="0x0">
    <title>Road Load Model - Peak Speed Decay Gain (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The model&#x27;s peak speed follows a rising speed at once and falls toward the speed by this fraction per update. Part of the road load model, which lowers the highest gear the transmission may use (the top gear cap) on grades or with a heavy load and raises it again when the load eases. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1498</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38454" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xC1B" flags="0x30">
    <title>Road Load Model - Score Factor vs Peak Speed by Gear (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 5][5 words]; COUNT is a structure word. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cap score factor by the model&#x27;s peak speed (columns) and current gear (rows). The score factors are multiplied together (1.0 = no change); a high score lowers the top gear cap. Part of the road load model, which lowers the highest gear the transmission may use (the top gear cap) on grades or with a heavy load and raises it again when the load eases. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1498</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="128" />
      <LABEL index="4" value="192" />
      <LABEL index="5" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x388DE" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC1C" flags="0x30">
    <title>Road Load Model - Score Factor vs Time in Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cap score factor by the time spent in the current gear or range. The score factors are multiplied together (1.0 = no change); a high score lowers the top gear cap. Part of the road load model, which lowers the highest gear the transmission may use (the top gear cap) on grades or with a heavy load and raises it again when the load eases. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1498</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>s (time in gear)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="25.6" />
      <LABEL index="2" value="51.2" />
      <LABEL index="3" value="76.8" />
      <LABEL index="4" value="102.4" />
      <LABEL index="5" value="128" />
      <LABEL index="6" value="153.6" />
      <LABEL index="7" value="179.2" />
      <LABEL index="8" value="204.8" />
      <LABEL index="9" value="230.4" />
      <LABEL index="10" value="256" />
      <LABEL index="11" value="281.6" />
      <LABEL index="12" value="307.2" />
      <LABEL index="13" value="332.8" />
      <LABEL index="14" value="358.4" />
      <LABEL index="15" value="384" />
      <LABEL index="16" value="409.6" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38612" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC1D" flags="0x30">
    <title>Upshift Pressure Ramp While Decelerating - Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rate at which the upshift pressure is raised, by shift (stock 0: no ramp). Upshift pressure ramp while decelerating: during an upshift, while the vehicle is decelerating (the released trans decel flag) and the gear ratio has not yet dropped to the ratio limit, the upshift pressure is raised at the ramp rate. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1499</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A24A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa/s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>163837.500000</max>
      <MATH equation="X*2.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC1E" flags="0x30">
    <title>Upshift Pressure Ramp While Decelerating - Ratio Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The ramp runs only while the gear ratio is above this, by shift (stock 1.79 / 1.10 / 0.75). Upshift pressure ramp while decelerating: during an upshift, while the vehicle is decelerating (the released trans decel flag) and the gear ratio has not yet dropped to the ratio limit, the upshift pressure is raised at the ramp rate. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1499</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A250" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC1F" flags="0x30">
    <title>Garage Shift Learning - Step vs Time Error, Into Drive (A) (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Step added to the learned first phase time correction, by the time error, for shifts into Drive with low converter slip (stock 3.2 s everywhere). Garage shift learning: after a garage shift the measured time to the third phase (times the time factor) is compared with the first phase time limit; the step from this curve is added to the learned first phase time correction. Learning never runs on the stock calibration: the maximum correction is 0 s and the fluid temperature and RPM windows are closed (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1500</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>s (time error)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-1.000" />
      <LABEL index="1" value="-0.875" />
      <LABEL index="2" value="-0.750" />
      <LABEL index="3" value="-0.625" />
      <LABEL index="4" value="-0.500" />
      <LABEL index="5" value="-0.375" />
      <LABEL index="6" value="-0.250" />
      <LABEL index="7" value="-0.125" />
      <LABEL index="8" value="0.000" />
      <LABEL index="9" value="0.125" />
      <LABEL index="10" value="0.250" />
      <LABEL index="11" value="0.375" />
      <LABEL index="12" value="0.500" />
      <LABEL index="13" value="0.625" />
      <LABEL index="14" value="0.750" />
      <LABEL index="15" value="0.875" />
      <LABEL index="16" value="1.000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37D6E" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>-3.200000</min>
      <max>3.175000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC20" flags="0x30">
    <title>Garage Shift Learning - Step vs Time Error, Other Garage Shifts (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Step added to the learned first phase time correction, by the time error, for every other garage shift (stock 3.2 s everywhere). Garage shift learning: after a garage shift the measured time to the third phase (times the time factor) is compared with the first phase time limit; the step from this curve is added to the learned first phase time correction. Learning never runs on the stock calibration: the maximum correction is 0 s and the fluid temperature and RPM windows are closed (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1500</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>s (time error)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-1.000" />
      <LABEL index="1" value="-0.875" />
      <LABEL index="2" value="-0.750" />
      <LABEL index="3" value="-0.625" />
      <LABEL index="4" value="-0.500" />
      <LABEL index="5" value="-0.375" />
      <LABEL index="6" value="-0.250" />
      <LABEL index="7" value="-0.125" />
      <LABEL index="8" value="0.000" />
      <LABEL index="9" value="0.125" />
      <LABEL index="10" value="0.250" />
      <LABEL index="11" value="0.375" />
      <LABEL index="12" value="0.500" />
      <LABEL index="13" value="0.625" />
      <LABEL index="14" value="0.750" />
      <LABEL index="15" value="0.875" />
      <LABEL index="16" value="1.000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37D81" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>-3.200000</min>
      <max>3.175000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xC21" flags="0x0">
    <title>Garage Shift Learning - Measured Time Factor, Into Drive (A) (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the measured time to the third phase before it is compared with the first phase time limit (stock 0). Garage shift learning: after a garage shift the measured time to the third phase (times the time factor) is compared with the first phase time limit; the step from this curve is added to the learned first phase time correction. Learning never runs on the stock calibration: the maximum correction is 0 s and the fluid temperature and RPM windows are closed (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1500</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x37D9E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC22" flags="0x0">
    <title>Garage Shift Learning - Measured Time Factor, Other Garage Shifts (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the measured time to the third phase before it is compared with the first phase time limit (stock 0). Garage shift learning: after a garage shift the measured time to the third phase (times the time factor) is compared with the first phase time limit; the step from this curve is added to the learned first phase time correction. Learning never runs on the stock calibration: the maximum correction is 0 s and the fluid temperature and RPM windows are closed (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1500</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x37DA0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC23" flags="0x0">
    <title>Turbine Speed Prediction - Output Acceleration Lead Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Look-ahead time on output shaft acceleration used to predict turbine speed during an upshift (stock 20.56 s). The prediction is used only by a shift torque path that is switched off on the stock calibration and by an engine speed predictor that is not used, so there is no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1501</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C89E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>65.535000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC24" flags="0x0">
    <title>O2 Response Test Credit - Airflow Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The credit grows only while mass airflow is at or above this (stock 20 g/s), with the throttle, engine speed and manifold pressure minimums also met. Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34796" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC25" flags="0x0">
    <title>O2 Response Test Credit - Engine Speed Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The credit grows only while engine speed is at or above this (stock 1500 rpm). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3479C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC26" flags="0x0">
    <title>O2 Response Test Credit - Throttle Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The credit grows only while throttle position, with the share used for idle air taken out, is at or above this (stock 5 %). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC27" flags="0x0">
    <title>O2 Response Test Credit - Manifold Pressure Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The credit grows only while manifold pressure is at or above this (stock 30 kPa). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC28" flags="0x0">
    <title>O2 Response Test Credit - Stopped Idle Time Limit (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After the throttle has been closed with the vehicle stopped for longer than this, the credit falls each update (stock 5 s). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC29" flags="0x0">
    <title>O2 Response Test Credit - Closed Throttle Coast Time Limit (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After the throttle has been closed with the vehicle moving for longer than this, the credit falls each update (stock 5 s). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC2A" flags="0x0">
    <title>O2 Response Test Credit - Step Down, Cylinders Not Fuelled (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Credit taken off each update while not every cylinder is being fuelled (stock 3). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC2B" flags="0x0">
    <title>O2 Response Test Credit - Step Down, Stopped Idle (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Credit taken off each update after the stopped idle time limit (stock 1). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC2C" flags="0x0">
    <title>O2 Response Test Credit - Step Down, Closed Throttle Coast (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Credit taken off each update after the closed throttle coast time limit (stock 1). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC2D" flags="0x0">
    <title>O2 Response Test Credit - Step Up (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Credit added each update while every minimum is met (stock 3). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC2E" flags="0x0">
    <title>O2 Response Test Credit - Required Credit (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The response test samples only while the credit is at or above this (stock 0: never blocks). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x347C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC2F" flags="0x0">
    <title>Airflow Mode 2 Entry Window A - Engine Speed Maximum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window A allows the mode up to this engine speed (scaled by the intake air temperature factor). Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC30" flags="0x0">
    <title>Airflow Mode 2 Entry Window B - Engine Speed Maximum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window B allows the mode up to this engine speed (scaled by the intake air temperature factor). Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC31" flags="0x0">
    <title>Airflow Mode 2 Entry Window A - Engine Speed Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window A allows the mode only above this engine speed (scaled by the intake air temperature factor). Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC32" flags="0x0">
    <title>Airflow Mode 2 Entry Window B - Engine Speed Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window B allows the mode only above this engine speed (scaled by the intake air temperature factor). Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC33" flags="0x0">
    <title>Airflow Mode 2 Entry Window A - Throttle Area Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window A allows the mode only at or above this throttle area. Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC34" flags="0x0">
    <title>Airflow Mode 2 Entry Window B - Throttle Area Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window B allows the mode only at or above this throttle area. Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC35" flags="0x0">
    <title>Airflow Mode 2 Entry Window A - Manifold Vacuum Maximum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window A allows the mode only while manifold vacuum (barometric minus manifold pressure) is at or below this. Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC36" flags="0x0">
    <title>Airflow Mode 2 Entry Window B - Manifold Vacuum Maximum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window B allows the mode only while manifold vacuum (barometric minus manifold pressure) is at or below this. Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xC37" flags="0x30">
    <title>Idle RPM Event - Airflow Adder (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added during the hold time of an rpm event. Row 1 In Gear, row 2 Park / Neutral; column rise / drop. Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1505</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>event</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="rise" />
      <LABEL index="1" value="drop" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>transmission</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="In Gear" />
      <LABEL index="1" value="Park / Neutral" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A016" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC38" flags="0x30">
    <title>Idle RPM Event - Adder Decay Rate (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After the hold time the adder shrinks by this fraction of itself each update; 0 ends it at once. Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1505</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>event</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="rise" />
      <LABEL index="1" value="drop" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A01E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC39" flags="0x30">
    <title>Idle RPM Event - Learn Pause Time After Decay (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After the adder has decayed, the idle airflow integral and learning stay paused for this long. Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1505</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>event</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="rise" />
      <LABEL index="1" value="drop" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A022" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC3A" flags="0x30">
    <title>Idle RPM Event - Adder Hold Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the event airflow adder is held before it decays. Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1505</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>event</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="rise" />
      <LABEL index="1" value="drop" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A026" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xC3B" flags="0x0">
    <title>Idle RPM Event - Engine Speed Margin Above Desired Idle (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The event sequence only continues while engine speed is below desired idle plus this. Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1505</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A02A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC3C" flags="0x0">
    <title>Idle RPM Event - Vehicle Speed Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The event sequence only continues while vehicle speed is below this. Stock 0: never. Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1505</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A02C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC3D" flags="0x0">
    <title>Idle RPM Event - Minimum Time Since Last Event (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A new event of the same direction only starts the adder when this long has passed since the last one. Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1505</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A02E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC3E" flags="0x0">
    <title>Scheduled Downshift Delay - Minimum Vehicle Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The delay applies only at or above this vehicle speed (stock 53 km/h). Scheduled downshift delay: when the shift schedule asks for a downshift while vehicle speed and throttle are at or above the limits (in Drive ranges), the downshift out of 3rd is delayed by the 3rd gear time, and the next downshift out of 2nd by the 2nd gear time. The stock times are 0, so there is no delay (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1506</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39E54" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC3F" flags="0x0">
    <title>Scheduled Downshift Delay - Minimum Throttle (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The delay applies only at or above this shift throttle (stock 50 %). Scheduled downshift delay: when the shift schedule asks for a downshift while vehicle speed and throttle are at or above the limits (in Drive ranges), the downshift out of 3rd is delayed by the 3rd gear time, and the next downshift out of 2nd by the 2nd gear time. The stock times are 0, so there is no delay (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1506</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39E56" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC40" flags="0x0">
    <title>Scheduled Downshift Delay - Time in 3rd (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long a scheduled downshift out of 3rd is held (stock 0 s). Scheduled downshift delay: when the shift schedule asks for a downshift while vehicle speed and throttle are at or above the limits (in Drive ranges), the downshift out of 3rd is delayed by the 3rd gear time, and the next downshift out of 2nd by the 2nd gear time. The stock times are 0, so there is no delay (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1506</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39E58" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC41" flags="0x0">
    <title>Scheduled Downshift Delay - Time in 2nd (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the next scheduled downshift out of 2nd is held, after a delayed downshift out of 3rd (stock 0 s). Scheduled downshift delay: when the shift schedule asks for a downshift while vehicle speed and throttle are at or above the limits (in Drive ranges), the downshift out of 3rd is delayed by the 3rd gear time, and the next downshift out of 2nd by the 2nd gear time. The stock times are 0, so there is no delay (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1506</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39E5A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC42" flags="0x0">
    <title>1st Gear Limit After Downshift into 3rd - Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time after a downshift into 3rd during which a command for 1st is limited to 2nd (stock 0 s). Downshift to 1st limit after a downshift into 3rd: within this time after a downshift into 3rd, a command for 1st becomes 2nd while the gear ratio is below the ratio limit. The stock time is 0, so this never applies (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1506</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39E5E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC43" flags="0x0">
    <title>1st Gear Limit After Downshift into 3rd - Ratio Limit (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The limit applies only while the gear ratio is below this (stock 0). Downshift to 1st limit after a downshift into 3rd: within this time after a downshift into 3rd, a command for 1st becomes 2nd while the gear ratio is below the ratio limit. The stock time is 0, so this never applies (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1506</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39E60" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC44" flags="0x0">
    <title>Line Pressure Tip-In - Throttle Filter Gain (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of the change in throttle taken into the filtered throttle each update (0 = follows at once). Line pressure is raised while the throttle is above its own filtered value (a quick throttle rise). Stock every value is 0, so no pressure is added: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0247, ledger:E1507</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C88E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC45" flags="0x0">
    <title>Line Pressure Tip-In - Min Throttle Rise (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pressure is only added when the throttle is at least this far above its filtered value. Line pressure is raised while the throttle is above its own filtered value (a quick throttle rise). Stock every value is 0, so no pressure is added: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0247, ledger:E1507</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C892" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC46" flags="0x0">
    <title>Line Pressure Tip-In - Pressure per Throttle Rise (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Line pressure added per percent of throttle rise. Line pressure is raised while the throttle is above its own filtered value (a quick throttle rise). Stock every value is 0, so no pressure is added: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0247, ledger:E1507</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C890" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa per %</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.279980</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/51200"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC47" flags="0x0">
    <title>Line Pressure Tip-In - Max Added Pressure (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most line pressure the throttle rise can add. Line pressure is raised while the throttle is above its own filtered value (a quick throttle rise). Stock every value is 0, so no pressure is added: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0247, ledger:E1507</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3C88C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC48" flags="0x0">
    <title>Idle Cold Request - Desired Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Desired idle requested while the cold idle request is active. Stock 550 rpm. Cold idle request: until the engine coolant has reached the limit at least once since start, desired idle is raised to at least the request speed (desired idle is the highest of all idle speed requests). Effect: raise = higher idle speed in a cold engine until the coolant limit is reached Evidence: ledger:E1508</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2A57A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xC49" flags="0x30">
    <title>Idle Altitude Up - Desired Idle Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to desired idle while the altitude idle-up is active. Stock 0. Altitude idle-up: at low barometric pressure (below Idle Altitude Up Baro) with coolant below the limit, desired idle is raised by the altitude adder. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1508</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>transmission</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="In Gear" />
      <LABEL index="1" value="Park / Neutral" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A07A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC4A" flags="0x30">
    <title>Upshift Alternate Pressure - Power-On Delay After Ratio Change Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In a back-to-back power-on upshift (or after a tip-in during one) the alternate table takes over once the ratio has been changing this long (stock 0: one update after the ratio starts to change). Only used when an upshift into the highest gear the selected range allows is commanded while the previous shift is still finishing (back-to-back upshifts); a single upshift uses the Base Shift Pressure - Alternate table from its start when power is on. Effect: raise = the alternate table takes over later in a back-to-back upshift Evidence: ledger:E1030, ledger:E1509</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38994" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC4B" flags="0x30">
    <title>Upshift Alternate Pressure - Power-On Tracking Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time into the ratio change after which a power-on upshift is tracked as established (stock 0). Only used when an upshift into the highest gear the selected range allows is commanded while the previous shift is still finishing (back-to-back upshifts); a single upshift uses the Base Shift Pressure - Alternate table from its start when power is on. Effect: changes when the power-on tracking settles Evidence: ledger:E1030, ledger:E1509</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3899A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC4C" flags="0x30">
    <title>Upshift Alternate Pressure - Time at New Gear Before Reset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time at the new gear ratio before the tracking resets (stock 0). Only used when an upshift into the highest gear the selected range allows is commanded while the previous shift is still finishing (back-to-back upshifts); a single upshift uses the Base Shift Pressure - Alternate table from its start when power is on. Effect: changes when the tracking resets after the shift Evidence: ledger:E1030, ledger:E1509</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x389A0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC4D" flags="0x30">
    <title>Upshift Alternate Pressure - Power-Off Delay After Command</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In a back-to-back upshift that starts with low torque, time after the command before the tracking allows a later tip-in to use the alternate table (stock 0). Only used when an upshift into the highest gear the selected range allows is commanded while the previous shift is still finishing (back-to-back upshifts); a single upshift uses the Base Shift Pressure - Alternate table from its start when power is on. Effect: raise = an early tip-in does not switch to the alternate table Evidence: ledger:E1030, ledger:E1509</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x389A6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC4E" flags="0x30">
    <title>Road Load Model - Climb Index Grade Force Term (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Force used for the climb index by the estimated grade force (stock identity would be 1:1). Part of the road load model&#x27;s climb index: (grade force term minus torque term) times speed divided by the truck&#x27;s weight, an equivalent climb rate, accumulated over time; a high index lowers the top gear cap. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1510</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>N (grade force)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="500" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1500" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2500" />
      <LABEL index="6" value="3000" />
      <LABEL index="7" value="3500" />
      <LABEL index="8" value="4000" />
      <LABEL index="9" value="4500" />
      <LABEL index="10" value="5000" />
      <LABEL index="11" value="5500" />
      <LABEL index="12" value="6000" />
      <LABEL index="13" value="6500" />
      <LABEL index="14" value="7000" />
      <LABEL index="15" value="7500" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38736" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>N</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC4F" flags="0x30">
    <title>Road Load Model - Climb Index Scale on Cap Change (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the top gear cap changes the climb index is multiplied by this, by current gear. Part of the road load model&#x27;s climb index: (grade force term minus torque term) times speed divided by the truck&#x27;s weight, an equivalent climb rate, accumulated over time; a high index lowers the top gear cap. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1510</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x384A0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xC50" flags="0x0">
    <title>Pedal Sensor 1 Circuit Test - Voltage High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal position sensor 1 reads as out of range (P2122 / P2123) above this voltage. Stock 4.68 V. Effect: widening the range = a faulty pedal sensor signal is caught later Evidence: ledger:E1512</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B68" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.999924</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13107.2"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC51" flags="0x0">
    <title>Pedal Sensor 1 Circuit Test - Voltage Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal position sensor 1 reads as out of range (P2122 / P2123) below this voltage. Stock 0.75 V. Effect: widening the range = a faulty pedal sensor signal is caught later Evidence: ledger:E1512</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B6A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.999924</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13107.2"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC52" flags="0x0">
    <title>Pedal Sensor 2 Circuit Test - Voltage Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal position sensor 2 reads as out of range (P2127 / P2128) below this voltage. Stock 2.60 V. Effect: widening the range = a faulty pedal sensor signal is caught later Evidence: ledger:E1512</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B72" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.999924</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13107.2"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC53" flags="0x0">
    <title>Pedal Sensor 2 Circuit Test - Voltage High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal position sensor 2 reads as out of range (P2127 / P2128) above this voltage. Stock 4.68 V. Effect: widening the range = a faulty pedal sensor signal is caught later Evidence: ledger:E1512</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B86" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.999924</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13107.2"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC54" flags="0x0">
    <title>Pedal Sensor 1 Circuit Test - Out of Range Time in Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal sensor 1 circuit fault when the sensor has been out of range for this long in total within one test window (time in 12.5 ms steps). Stock 0.25 s. Effect: raise = more out-of-range time is tolerated before the fault Evidence: ledger:E1515</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B6C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>819.187500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/80"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC55" flags="0x0">
    <title>Pedal Sensor 1 Circuit Test - Continuous Out of Range Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal sensor 1 circuit fault when the sensor stays out of range for this long without a break (time in 12.5 ms steps). Stock 0.125 s. Effect: raise = a longer continuous out-of-range reading is tolerated Evidence: ledger:E1515</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B6E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>819.187500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/80"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC56" flags="0x0">
    <title>Pedal Sensor 1 Circuit Test - Window Length</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Length of the test window that starts at the first out-of-range reading; if the accumulated limit is not reached by then, the counts restart (time in 12.5 ms steps). Stock 0.5 s. Effect: raise = intermittent out-of-range readings are collected over a longer time Evidence: ledger:E1515</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B70" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>819.187500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/80"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC57" flags="0x0">
    <title>Pedal Sensor 2 Circuit Test - Out of Range Time in Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal sensor 2 circuit fault when the sensor has been out of range for this long in total within one test window (time in 12.5 ms steps). Stock 0.19 s. Effect: raise = more out-of-range time is tolerated before the fault Evidence: ledger:E1515</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B76" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>819.187500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/80"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC58" flags="0x0">
    <title>Pedal Sensor 2 Circuit Test - Continuous Out of Range Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal sensor 2 circuit fault when the sensor stays out of range for this long without a break (time in 12.5 ms steps). Stock 0.125 s. Effect: raise = a longer continuous out-of-range reading is tolerated Evidence: ledger:E1515</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B78" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>819.187500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/80"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC59" flags="0x0">
    <title>Pedal Sensor 2 Circuit Test - Window Length</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Length of the test window that starts at the first out-of-range reading; if the accumulated limit is not reached by then, the counts restart (time in 12.5 ms steps). Stock 0.44 s. Effect: raise = intermittent out-of-range readings are collected over a longer time Evidence: ledger:E1515</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B7A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>819.187500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/80"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xC5A" flags="0x30">
    <title>WOT Shift Anticipation Learning - Step vs Overshoot</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learning step by overshoot time error (positive = the engine went past the shift point; stock 0 everywhere). WOT shift anticipation learning: at an upshift request the PCM notes the WOT upshift rpm point and the engine speed&#x27;s rate of rise, tracks the peak engine speed for the tracking time, and turns the overshoot (peak above the shift point, divided by the rate) into a time error. The step from the step curve is added, through the gains, to a learned anticipation time by shift and fluid temperature, which is added to the WOT Shift - Engine Speed Anticipation Time table. Inactive on the 2006 H3. Whether it is active on...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>ms (overshoot time error)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-409" />
      <LABEL index="1" value="-307" />
      <LABEL index="2" value="-204" />
      <LABEL index="3" value="-102" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="102" />
      <LABEL index="6" value="204" />
      <LABEL index="7" value="307" />
      <LABEL index="8" value="409" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39084" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>ms</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xC5B" flags="0x0">
    <title>WOT Shift Anticipation Learning - Gain, Current Cell</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the step added to the learned time at the current fluid temperature (stock 0). WOT shift anticipation learning: at an upshift request the PCM notes the WOT upshift rpm point and the engine speed&#x27;s rate of rise, tracks the peak engine speed for the tracking time, and turns the overshoot (peak above the shift point, divided by the rate) into a time error. The step from the step curve is added, through the gains, to a learned anticipation time by shift and fluid temperature, which is added to the WOT Shift - Engine Speed Anticipation Time table. Inactive on the 2006 H3. Whether it is active on this operating system...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39096" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC5C" flags="0x0">
    <title>WOT Shift Anticipation Learning - Gain, Colder Neighbour Cell</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the step added to the next colder cell (stock 0). WOT shift anticipation learning: at an upshift request the PCM notes the WOT upshift rpm point and the engine speed&#x27;s rate of rise, tracks the peak engine speed for the tracking time, and turns the overshoot (peak above the shift point, divided by the rate) into a time error. The step from the step curve is added, through the gains, to a learned anticipation time by shift and fluid temperature, which is added to the WOT Shift - Engine Speed Anticipation Time table. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Eff...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39098" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC5D" flags="0x0">
    <title>WOT Shift Anticipation Learning - Gain, Warmer Neighbour Cell</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the step added to the next warmer cell (stock 0). WOT shift anticipation learning: at an upshift request the PCM notes the WOT upshift rpm point and the engine speed&#x27;s rate of rise, tracks the peak engine speed for the tracking time, and turns the overshoot (peak above the shift point, divided by the rate) into a time error. The step from the step curve is added, through the gains, to a learned anticipation time by shift and fluid temperature, which is added to the WOT Shift - Engine Speed Anticipation Time table. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Eff...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3909A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xC5E" flags="0x30">
    <title>WOT Shift Anticipation Learning - Learned Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest learned anticipation time, by shift (stock 0 ms). WOT shift anticipation learning: at an upshift request the PCM notes the WOT upshift rpm point and the engine speed&#x27;s rate of rise, tracks the peak engine speed for the tracking time, and turns the overshoot (peak above the shift point, divided by the rate) into a time error. The step from the step curve is added, through the gains, to a learned anticipation time by shift and fluid temperature, which is added to the WOT Shift - Engine Speed Anticipation Time table. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effec...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39058" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>ms</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC5F" flags="0x30">
    <title>WOT Shift Anticipation Learning - Learned Time Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest learned anticipation time, by shift (stock 0 ms: nothing is learned). WOT shift anticipation learning: at an upshift request the PCM notes the WOT upshift rpm point and the engine speed&#x27;s rate of rise, tracks the peak engine speed for the tracking time, and turns the overshoot (peak above the shift point, divided by the rate) into a time error. The step from the step curve is added, through the gains, to a learned anticipation time by shift and fluid temperature, which is added to the WOT Shift - Engine Speed Anticipation Time table. Inactive on the 2006 H3. Whether it is active on this operating system has not b...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3905E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>ms</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC60" flags="0x30">
    <title>WOT Shift Anticipation Learning - Minimum Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Steps smaller than this are not learned, by shift (stock 0 ms). WOT shift anticipation learning: at an upshift request the PCM notes the WOT upshift rpm point and the engine speed&#x27;s rate of rise, tracks the peak engine speed for the tracking time, and turns the overshoot (peak above the shift point, divided by the rate) into a time error. The step from the step curve is added, through the gains, to a learned anticipation time by shift and fluid temperature, which is added to the WOT Shift - Engine Speed Anticipation Time table. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39064" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ms</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC61" flags="0x30">
    <title>WOT Shift Anticipation Learning - Peak Tracking Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time after the upshift request during which the peak engine speed is tracked before learning, by shift (stock 0.5 s). WOT shift anticipation learning: at an upshift request the PCM notes the WOT upshift rpm point and the engine speed&#x27;s rate of rise, tracks the peak engine speed for the tracking time, and turns the overshoot (peak above the shift point, divided by the rate) into a time error. The step from the step curve is added, through the gains, to a learned anticipation time by shift and fluid temperature, which is added to the WOT Shift - Engine Speed Anticipation Time table. The stock learned time limits are 0 to 0...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3906A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC62" flags="0x30">
    <title>WOT Shift Anticipation Learning - Minimum Fluid Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learning starts only at or above this fluid temperature, by shift (stock 0 C). WOT shift anticipation learning: at an upshift request the PCM notes the WOT upshift rpm point and the engine speed&#x27;s rate of rise, tracks the peak engine speed for the tracking time, and turns the overshoot (peak above the shift point, divided by the rate) into a time error. The step from the step curve is added, through the gains, to a learned anticipation time by shift and fluid temperature, which is added to the WOT Shift - Engine Speed Anticipation Time table. Inactive on the 2006 H3. Whether it is active on this operating system has not...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39076" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC63" flags="0x30">
    <title>WOT Shift Anticipation Learning - Maximum Fluid Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learning starts only at or below this fluid temperature, by shift (stock 0 C). WOT shift anticipation learning: at an upshift request the PCM notes the WOT upshift rpm point and the engine speed&#x27;s rate of rise, tracks the peak engine speed for the tracking time, and turns the overshoot (peak above the shift point, divided by the rate) into a time error. The step from the step curve is added, through the gains, to a learned anticipation time by shift and fluid temperature, which is added to the WOT Shift - Engine Speed Anticipation Time table. Inactive on the 2006 H3. Whether it is active on this operating system has not...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3907C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xC64" flags="0x0">
    <title>2nd Gear Hold After 1-2 Upshift - Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long after a 1-2 upshift a command back to 1st is held in 2nd (stock 0 s). 2nd gear hold after a 1-2 upshift: for this time after a 1-2 upshift is commanded at or above the minimum speed, a command back to 1st is held in 2nd, in Drive and two neighbouring range positions (not the low ranges), while brake switch B is not active. The stock time is 0, so this never applies (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1518</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39E64" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC65" flags="0x0">
    <title>2nd Gear Hold After 1-2 Upshift - Minimum Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The hold time starts only for a 1-2 upshift commanded at or above this vehicle speed (stock 0 km/h). 2nd gear hold after a 1-2 upshift: for this time after a 1-2 upshift is commanded at or above the minimum speed, a command back to 1st is held in 2nd, in Drive and two neighbouring range positions (not the low ranges), while brake switch B is not active. The stock time is 0, so this never applies (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1518</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39E66" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC66" flags="0x0">
    <title>Road Load Model - Grade Index Decay Step, Low Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Removed from a positive grade index each update while speed is below the Climb Index Min Speed. Part of the road load model&#x27;s grade index: the estimated grade force times speed divided by the truck&#x27;s weight, an equivalent climb rate, accumulated over time; a high index lowers the top gear cap. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1520</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3846E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>m/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>159.997559</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/409.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xC67" flags="0x30">
    <title>Airmass Predictor - Blend Toward Prediction, Alternate Mode (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Used in place of Blend Toward Prediction while the predictor&#x27;s alternate mode is active: fraction of the way from the prediction to the filtered MAF airmass that the airmass estimate takes (0 = prediction only, 1.0 = filtered MAF airmass only; stock 1.0 in every region, so in alternate mode the estimate follows the filtered MAF airmass). Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C4A8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC68" flags="0x30">
    <title>Road Load Model - Climb Index Torque Term (dormant)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Force taken off the climb index&#x27;s grade force term, by gear and gearbox input torque, while converter slip is above the Climb Index Torque Term Min Slip. Part of the road load model&#x27;s climb index: (grade force term minus this torque term) times speed divided by the truck&#x27;s weight, an equivalent climb rate, accumulated over time; a high index lowers the top gear cap. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0779, ledge...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <LABEL index="3" value="200" />
      <LABEL index="4" value="300" />
      <LABEL index="5" value="400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3887E" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>N</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC69" flags="0x30">
    <title>TCC Upshift Boost vs Line Pressure (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 9][9 values]; COUNT is a structure word - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Amount the full-command clutch pressure is lowered during an upshift, by shift and line pressure (stock 0). Converter clutch upshift boost: from an upshift request the clutch command is computed as if the full-command clutch pressure were lower by the boost (by line pressure), which raises the clutch command. Once the gear ratio starts to change the boost is held for the hold time, then ramped out over the ramp time. A hold time of 0 with a nonzero boost keeps the boost after the shift. The stock boost is 0 everywhere, so there is no effect (dor...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3D4F8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>10</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT; data columns: kPa (line pressure))</units>
      <embedinfo type="1" />
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C918" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC6A" flags="0x30">
    <title>TCC Upshift Boost - Hold Time vs Line Pressure (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 9][9 values]; COUNT is a structure word - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the boost is held after the gear ratio starts to change, by shift and line pressure (stock 0 s). Converter clutch upshift boost: from an upshift request the clutch command is computed as if the full-command clutch pressure were lower by the boost (by line pressure), which raises the clutch command. Once the gear ratio starts to change the boost is held for the hold time, then ramped out over the ramp time. A hold time of 0 with a nonzero boost keeps the boost after the shift. The stock boost is 0 everywhere, so there is no effect (dorma...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3D4F8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>10</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT; data columns: kPa (line pressure))</units>
      <embedinfo type="1" />
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C8DC" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC6B" flags="0x30">
    <title>TCC Upshift Boost - Ramp Out Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time over which the boost is ramped out after the hold time, by shift (stock 0 s). Converter clutch upshift boost: from an upshift request the clutch command is computed as if the full-command clutch pressure were lower by the boost (by line pressure), which raises the clutch command. Once the gear ratio starts to change the boost is held for the hold time, then ramped out over the ramp time. A hold time of 0 with a nonzero boost keeps the boost after the shift. The stock boost is 0 everywhere, so there is no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1529</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C954" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC6C" flags="0x30">
    <title>TAP Learn - Min Vehicle Speed by Shift</title>
    <description>Change in small steps and log. Each row is [COUNT = 17][17 points]; COUNT is a structure word, never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this trans-side vehicle speed a shift is not learned. Stock 0 for every shift (no lower limit). Pairs with TAP Learn - Max Vehicle Speed by Shift; TAP (adaptive shift pressure) only learns on shifts inside every enable window. Effect: which shifts TAP learns from Evidence: ledger:E0366, ledger:E0714, ledger:E1530</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="19" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="31" />
      <LABEL index="7" value="38" />
      <LABEL index="8" value="44" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="56" />
      <LABEL index="11" value="62" />
      <LABEL index="12" value="69" />
      <LABEL index="13" value="75" />
      <LABEL index="14" value="81" />
      <LABEL index="15" value="88" />
      <LABEL index="16" value="94" />
      <LABEL index="17" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C2A6" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC6D" flags="0x30">
    <title>Downshift Pressure Adder by Downshift</title>
    <description>Change in small steps and log. Each row is [COUNT = 17][17 points]; COUNT is a structure word, never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift pressure added for the downshift, by base shift pressure. While the gear ratio is changing it is brought in by how far the ratio has moved toward the new gear; not used in Park, Reverse or Neutral. Negative values lower the pressure. Stock 0 everywhere, so nothing is added. Effect: raise = firmer downshifts Evidence: ledger:E1531</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="120" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="200" />
      <LABEL index="7" value="240" />
      <LABEL index="8" value="280" />
      <LABEL index="9" value="320" />
      <LABEL index="10" value="360" />
      <LABEL index="11" value="400" />
      <LABEL index="12" value="440" />
      <LABEL index="13" value="480" />
      <LABEL index="14" value="520" />
      <LABEL index="15" value="560" />
      <LABEL index="16" value="600" />
      <LABEL index="17" value="640" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>downshift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="3-1" />
      <LABEL index="1" value="4-1" />
      <LABEL index="2" value="4-2" />
      <LABEL index="3" value="2-1" />
      <LABEL index="4" value="3-2" />
      <LABEL index="5" value="4-3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3BCB6" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xC6E" flags="0x0">
    <title>Road Load Model - Low Speed Rise Gain (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The model&#x27;s low speed follows a falling speed at once and rises toward the speed by this fraction per update. Part of the road load model&#x27;s release check, which raises the top gear cap again by one gear when a release term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1533</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38452" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xC6F" flags="0x30">
    <title>Road Load Model - Release Factor A vs Low Speed by Gear (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 5][5 words]; COUNT is a structure word. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Release term A factor by the model&#x27;s low speed (columns) and current gear (rows). Part of the road load model&#x27;s release check, which raises the top gear cap again by one gear when a release term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1533</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="128" />
      <LABEL index="4" value="192" />
      <LABEL index="5" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3890E" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC70" flags="0x30">
    <title>Road Load Model - Release Factor B vs Low Speed by Gear (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 5][5 words]; COUNT is a structure word. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Release term B by the model&#x27;s low speed (columns) and current gear (rows); term B is the larger of this and a second factor. Part of the road load model&#x27;s release check, which raises the top gear cap again by one gear when a release term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1533</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="128" />
      <LABEL index="4" value="192" />
      <LABEL index="5" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x388AE" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC71" flags="0x30">
    <title>Road Load Model - Release Factor vs Time in Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Release term C factor by the time spent in the current gear or range. Part of the road load model&#x27;s release check, which raises the top gear cap again by one gear when a release term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1533</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>s (time in gear)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="25.6" />
      <LABEL index="2" value="51.2" />
      <LABEL index="3" value="76.8" />
      <LABEL index="4" value="102.4" />
      <LABEL index="5" value="128" />
      <LABEL index="6" value="153.6" />
      <LABEL index="7" value="179.2" />
      <LABEL index="8" value="204.8" />
      <LABEL index="9" value="230.4" />
      <LABEL index="10" value="256" />
      <LABEL index="11" value="281.6" />
      <LABEL index="12" value="307.2" />
      <LABEL index="13" value="332.8" />
      <LABEL index="14" value="358.4" />
      <LABEL index="15" value="384" />
      <LABEL index="16" value="409.6" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x385EE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC72" flags="0x30">
    <title>Road Load Model - Release Factor vs Climb Index (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Release term A factor by the road load model&#x27;s climb index (Road Load Model - Climb Index). Part of the road load model&#x27;s release check, which raises the top gear cap again by one gear when a release term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1533</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>m/s (climb index)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="160" />
      <LABEL index="2" value="320" />
      <LABEL index="3" value="480" />
      <LABEL index="4" value="640" />
      <LABEL index="5" value="800" />
      <LABEL index="6" value="960" />
      <LABEL index="7" value="1120" />
      <LABEL index="8" value="1280" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x386A6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC73" flags="0x30">
    <title>Road Load Model - Release Limit A by Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Release when term A is above this, by current gear. Part of the road load model&#x27;s release check, which raises the top gear cap again by one gear when a release term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1533</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x384C8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC74" flags="0x30">
    <title>Road Load Model - Release Limit B by Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Release when term B is above this, by current gear. Part of the road load model&#x27;s release check, which raises the top gear cap again by one gear when a release term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1533</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x384D0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC75" flags="0x30">
    <title>Road Load Model - Release Limit C by Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Release when term C is above this, by current gear. Part of the road load model&#x27;s release check, which raises the top gear cap again by one gear when a release term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1533</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x384D8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC76" flags="0x30">
    <title>Road Load Model - Release Limit Weighted Sum by Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Release when the weighted sum of terms A and C is above this, by current gear. Part of the road load model&#x27;s release check, which raises the top gear cap again by one gear when a release term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1533</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x384E0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xC77" flags="0x0">
    <title>Barometric Pressure - Default Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Barometric pressure the PCM assumes when its stored barometric reading is lost (memory check fails) and when the barometric estimate is reset; the estimate is then updated from manifold pressure. Stock 100 kPa. Effect: raise = a higher starting barometric pressure after a memory loss or reset Evidence: ledger:E1534</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x21836" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC78" flags="0x0">
    <title>Airmass Model - Load Airmass Capped Prediction Weight (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the start-up blend is complete, the load airmass is the predicted cylinder airmass moved this fraction of the way toward the prediction capped by the maximum airflow curve (0 = uncapped prediction, 1.0 = capped prediction; stock 0.83). Part of the cylinder airmass model; reference only, DO NOT EDIT. During the start-up blend both values move from the speed-density airmass to this blend. Effect: reference only (airmass model) Evidence: ledger:E1535</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C282" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction (1.0 = capped prediction only)</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC79" flags="0x0">
    <title>Airmass Model - Fuel Airmass Second Prediction Weight (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the start-up blend is complete, the airmass used for base fuel is the capped prediction moved this fraction of the way toward the predictor&#x27;s second output, also capped by the maximum airflow curve (stock 0.67). Part of the cylinder airmass model; reference only, DO NOT EDIT. During the start-up blend both values move from the speed-density airmass to this blend. Effect: reference only (airmass model) Evidence: ledger:E1535</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C284" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction (1.0 = second capped prediction only)</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xC7A" flags="0x30">
    <title>Road Load Model - Score Factor A vs Climb Index (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Score term A factor by the road load model&#x27;s climb index (Road Load Model - Climb Index). Part of the road load model&#x27;s score check, which lowers the top gear cap when a score term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1536</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>m/s (climb index)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="160" />
      <LABEL index="2" value="320" />
      <LABEL index="3" value="480" />
      <LABEL index="4" value="640" />
      <LABEL index="5" value="800" />
      <LABEL index="6" value="960" />
      <LABEL index="7" value="1120" />
      <LABEL index="8" value="1280" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38636" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC7B" flags="0x30">
    <title>Road Load Model - Score Factor B vs Climb Index (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Score term B factor by the road load model&#x27;s climb index. Part of the road load model&#x27;s score check, which lowers the top gear cap when a score term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1536</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>m/s (climb index)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="160" />
      <LABEL index="2" value="320" />
      <LABEL index="3" value="480" />
      <LABEL index="4" value="640" />
      <LABEL index="5" value="800" />
      <LABEL index="6" value="960" />
      <LABEL index="7" value="1120" />
      <LABEL index="8" value="1280" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3864A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC7C" flags="0x30">
    <title>Road Load Model - Score Factor C vs Grade Index (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Score term C factor by the road load model&#x27;s grade index (Road Load Model - Grade Index). Part of the road load model&#x27;s score check, which lowers the top gear cap when a score term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1536</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>m/s (grade index)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="160" />
      <LABEL index="2" value="320" />
      <LABEL index="3" value="480" />
      <LABEL index="4" value="640" />
      <LABEL index="5" value="800" />
      <LABEL index="6" value="960" />
      <LABEL index="7" value="1120" />
      <LABEL index="8" value="1280" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x384FE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC7D" flags="0x30">
    <title>Road Load Model - Score Limit A by Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cap is lowered when term A is above this, by current gear. Part of the road load model&#x27;s score check, which lowers the top gear cap when a score term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1536</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x384A8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC7E" flags="0x30">
    <title>Road Load Model - Score Limit B by Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cap is lowered when term B is above this, by current gear. Part of the road load model&#x27;s score check, which lowers the top gear cap when a score term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1536</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x384B0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC7F" flags="0x30">
    <title>Road Load Model - Score Limit C by Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cap is lowered when term C is above this, by current gear. Part of the road load model&#x27;s score check, which lowers the top gear cap when a score term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1536</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x384B8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC80" flags="0x30">
    <title>Road Load Model - Score Limit Weighted Sum by Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cap is lowered when the weighted sum of terms A and B is above this, by current gear. Part of the road load model&#x27;s score check, which lowers the top gear cap when a score term passes its limit. Factors multiply together (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1536</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x384C0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xC81" flags="0x0">
    <title>Throttle Actuator Command - Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit on the commanded throttle actuator position: every update the throttle control clamps its command to this value. Stock 100.4 %, so it does not limit the stock calibration. Effect: lower = caps the throttle opening at this position Evidence: ledger:E1538</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x24F1C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC82" flags="0x0">
    <title>Throttle Actuator Command - Wide Open Status Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While the commanded throttle is at or above this, the PCM sets a wide-open bit in its throttle status reports (stock 98.4 %). Reporting only: the throttle command is not changed. Effect: reporting only Evidence: ledger:E1538</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x24F48" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC83" flags="0x0">
    <title>A/C Cut on 3-2 Kickdown - Pedal Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the transmission downshifts from 3rd to 2nd with the accelerator pedal above this, the A/C compressor is cut for the cut time. Stock 100 %. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: lower = the A/C is cut on 3-2 kickdowns at this pedal and above Evidence: ledger:E1540</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x381E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC84" flags="0x0">
    <title>A/C Cut on 3-2 Kickdown - Cut Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the A/C compressor stays cut after a 3-2 kickdown. Stock 0 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1540</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x381EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xC85" flags="0x30">
    <title>Minimum Line Pressure Range 6 - Fluid Temperature Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fluid temperature points of the range code 6 minimum line pressure factor curve. Stock all 0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1541</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x381EE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC86" flags="0x30">
    <title>Minimum Line Pressure Range 6 - Fluid Temperature Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier on the range code 6 minimum line pressure by fluid temperature (1.0 = table value). A controller flag can bypass it. Stock all 0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1541</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>fluid temperature (C)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3840E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC87" flags="0x30">
    <title>Road Load Model - Heat Temperature Set-Up Blend (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the model is set up, its heat temperature starts this fraction of the way from the fluid temperature back toward its stored value (0 = fluid temperature), by fluid temperature (columns) and by the stored fluid temperature minus the current one (rows). Part of the road load model&#x27;s heat temperature, which is heated by grade force times speed and cools toward intake air temperature; a hot model raises the cap score. The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0786, ledge...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>degC (fluid temperature)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-256" />
      <LABEL index="1" value="-128" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="128" />
      <LABEL index="4" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>degC (stored minus current fluid temperature)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-256" />
      <LABEL index="1" value="-128" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="128" />
      <LABEL index="4" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3884C" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC88" flags="0x30">
    <title>Road Load Model - Heat Temperature Cooling Gain (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the gap between the heat temperature and intake air temperature removed per cooling step (every 32 model updates), by vehicle speed. Part of the road load model&#x27;s heat temperature, which is heated by grade force times speed and cools toward intake air temperature; a hot model raises the cap score. The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0786, ledger:E1542</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="32" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="96" />
      <LABEL index="4" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38672" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>1.599976</max>
      <MATH equation="X/40960"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC89" flags="0x30">
    <title>Road Load Model - Heat Temperature Heating Gain (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Heat temperature rise per model update for each kW of grade force times speed (either direction of force), by grade force. Part of the road load model&#x27;s heat temperature, which is heated by grade force times speed and cools toward intake air temperature; a hot model raises the cap score. The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0786, ledger:E1542</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>N (grade force)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="500" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1500" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2500" />
      <LABEL index="6" value="3000" />
      <LABEL index="7" value="3500" />
      <LABEL index="8" value="4000" />
      <LABEL index="9" value="4500" />
      <LABEL index="10" value="5000" />
      <LABEL index="11" value="5500" />
      <LABEL index="12" value="6000" />
      <LABEL index="13" value="6500" />
      <LABEL index="14" value="7000" />
      <LABEL index="15" value="7500" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38712" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC per kW</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.545637</max>
      <MATH equation="X/42400"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC8A" flags="0x30">
    <title>Road Load Model - Score Factor vs Heat Temperature by Gear (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 9][9 words]; COUNT is a structure word. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cap score factor by the model&#x27;s heat temperature (columns) and current gear (rows); multiplies into score terms A and C. Part of the road load model&#x27;s heat temperature, which is heated by grade force times speed and cools toward intake air temperature; a hot model raises the cap score. The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0786, ledger:E1542</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="40" />
      <LABEL index="2" value="100" />
      <LABEL index="3" value="160" />
      <LABEL index="4" value="220" />
      <LABEL index="5" value="280" />
      <LABEL index="6" value="340" />
      <LABEL index="7" value="400" />
      <LABEL index="8" value="460" />
      <LABEL index="9" value="520" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38514" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC8B" flags="0x30">
    <title>Road Load Model - Release Factor vs Heat Temperature by Gear (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 9][9 words]; COUNT is a structure word. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cap release factor by the model&#x27;s heat temperature (columns) and current gear (rows); multiplies into release term C. Part of the road load model&#x27;s heat temperature, which is heated by grade force times speed and cools toward intake air temperature; a hot model raises the cap score. The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0786, ledger:E1542</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="40" />
      <LABEL index="2" value="100" />
      <LABEL index="3" value="160" />
      <LABEL index="4" value="220" />
      <LABEL index="5" value="280" />
      <LABEL index="6" value="340" />
      <LABEL index="7" value="400" />
      <LABEL index="8" value="460" />
      <LABEL index="9" value="520" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38564" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC8C" flags="0x30">
    <title>Road Load Model - Load Share Shaping (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Reshapes the road load model&#x27;s filtered load share (Road Load Model - Load Share) before the cap score uses it. The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1543</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>fraction (share)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.125" />
      <LABEL index="2" value="0.25" />
      <LABEL index="3" value="0.375" />
      <LABEL index="4" value="0.5" />
      <LABEL index="5" value="0.625" />
      <LABEL index="6" value="0.75" />
      <LABEL index="7" value="0.875" />
      <LABEL index="8" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3867E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC8D" flags="0x30">
    <title>Road Load Model - Reserve Share Shaping (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Reshapes the road load model&#x27;s filtered reserve force share before the cap release uses it. The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1543</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>fraction (share)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.125" />
      <LABEL index="2" value="0.25" />
      <LABEL index="3" value="0.375" />
      <LABEL index="4" value="0.5" />
      <LABEL index="5" value="0.625" />
      <LABEL index="6" value="0.75" />
      <LABEL index="7" value="0.875" />
      <LABEL index="8" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38692" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC8E" flags="0x30">
    <title>Road Load Model - Score Factor vs Load Share (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cap score factor by the shaped load share; multiplies into score terms A and C (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1543</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>fraction (share)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.125" />
      <LABEL index="2" value="0.25" />
      <LABEL index="3" value="0.375" />
      <LABEL index="4" value="0.5" />
      <LABEL index="5" value="0.625" />
      <LABEL index="6" value="0.75" />
      <LABEL index="7" value="0.875" />
      <LABEL index="8" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x384EA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC8F" flags="0x30">
    <title>Road Load Model - Release Factor vs Reserve Share (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cap release factor by the shaped reserve share; multiplies into release term C (1.0 = no change). The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1543</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>fraction (share)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.125" />
      <LABEL index="2" value="0.25" />
      <LABEL index="3" value="0.375" />
      <LABEL index="4" value="0.5" />
      <LABEL index="5" value="0.625" />
      <LABEL index="6" value="0.75" />
      <LABEL index="7" value="0.875" />
      <LABEL index="8" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x386C6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC90" flags="0x30">
    <title>Road Load Model - Score Block Force Limit by Gear (dormant)</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 9][9 words]; COUNT is a structure word. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Score check is held off while the gear force plus each filtered force is at or below this, by speed and current gear. Part of the road load model&#x27;s cap blocks: the score check (which lowers the top gear cap) and the release check (which raises it) are held off for a time after a cap change or a range change, and the score check while the gear force plus the filtered grade and drive forces stay within the Score Block Force Limit. The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="48" />
      <LABEL index="5" value="64" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="96" />
      <LABEL index="8" value="112" />
      <LABEL index="9" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38944" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>N</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xC91" flags="0x0">
    <title>Road Load Model - Score Unblock Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time after a cap or range change before the score check can be released again (both forces above the limit). Part of the road load model&#x27;s cap blocks: the score check (which lowers the top gear cap) and the release check (which raises it) are held off for a time after a cap change or a range change, and the score check while the gear force plus the filtered grade and drive forces stay within the Score Block Force Limit. The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledg...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3843E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC92" flags="0x0">
    <title>Road Load Model - Release Unblock Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time after a cap or range change before the release check runs again. Part of the road load model&#x27;s cap blocks: the score check (which lowers the top gear cap) and the release check (which raises it) are held off for a time after a cap change or a range change, and the score check while the gear force plus the filtered grade and drive forces stay within the Score Block Force Limit. The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1544</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38440" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC93" flags="0x0">
    <title>Road Load Model - Drive Force Peak Hold Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the peak drive force is held before it is taken again. Part of the road load model&#x27;s cap blocks: the score check (which lowers the top gear cap) and the release check (which raises it) are held off for a time after a cap change or a range change, and the score check while the gear force plus the filtered grade and drive forces stay within the Score Block Force Limit. The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1544</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3843C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC94" flags="0x0">
    <title>Road Load Model - Grade Force Filter Rise Gain (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the gap to a higher peak grade force taken per filter step (every 10 model updates). Part of the road load model&#x27;s cap blocks: the score check (which lowers the top gear cap) and the release check (which raises it) are held off for a time after a cap change or a range change, and the score check while the gear force plus the filtered grade and drive forces stay within the Score Block Force Limit. The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1544</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38442" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC95" flags="0x0">
    <title>Road Load Model - Grade Force Filter Fall Gain (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the gap to a lower peak grade force taken per filter step (every 10 model updates). Part of the road load model&#x27;s cap blocks: the score check (which lowers the top gear cap) and the release check (which raises it) are held off for a time after a cap change or a range change, and the score check while the gear force plus the filtered grade and drive forces stay within the Score Block Force Limit. The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1544</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38444" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC96" flags="0x0">
    <title>Road Load Model - Drive Force Filter Rise Gain (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the gap to a higher held drive force taken per filter step (every 10 model updates). Part of the road load model&#x27;s cap blocks: the score check (which lowers the top gear cap) and the release check (which raises it) are held off for a time after a cap change or a range change, and the score check while the gear force plus the filtered grade and drive forces stay within the Score Block Force Limit. The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1544</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38446" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC97" flags="0x0">
    <title>Road Load Model - Drive Force Filter Fall Gain (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the gap to a lower held drive force taken per filter step (every 10 model updates). Part of the road load model&#x27;s cap blocks: the score check (which lowers the top gear cap) and the release check (which raises it) are held off for a time after a cap change or a range change, and the score check while the gear force plus the filtered grade and drive forces stay within the Score Block Force Limit. The model is switched off on this truck, and the top gear cap is never lowered on this calibration, so this has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1544</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38448" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC98" flags="0x0">
    <title>TCC Release Ramp - Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the converter clutch pressure ramps down when the clutch is released (stock 1000 kPa/s). After a tip-in release the separate after tip-in rate is used instead. Effect: raise = the clutch lets go faster; lower = a softer, slower release Evidence: ledger:E1406, ledger:E1523, ledger:E1547</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D178" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>1000.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65.535"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xC99" flags="0x30">
    <title>WOT Shift Anticipation Learning - Cancel Time After Downshift Request</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A learning run is cancelled until this long after a downshift request, by shift (stock 0 s: only while the request is active). Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1548</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39070" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xC9A" flags="0x0">
    <title>Cold Engine Shift Limits - Temperature Source Select</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Which temperature the cold engine shift limits are checked against: 0 = corrected coolant temperature (stock), 1 = coolant sensor temperature, 2 = transmission fluid temperature, other values read 0. Effect: which temperature the cold engine shift limits are checked against Evidence: ledger:E1549, ledger:E1577</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39EC6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>index</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xC9B" flags="0x30">
    <title>Cam Sensor Performance - Minimum Edges per Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fewest cam edges per window that count as good (stock 475 / 275). Camshaft position sensor performance test (P0366 for cam input 1, P0341 for cam input 2): the cam edges counted in each test window must fall within the band; when enough windows fall outside it the code sets, otherwise the test passes after a set number of windows. Effect: raise = a cam signal that loses edges is flagged sooner Evidence: ledger:E1080, ledger:E1550</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D48" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>edges</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC9C" flags="0x30">
    <title>Cam Sensor Performance - Maximum Edges per Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most cam edges per window that count as good (stock 525 / 325). Camshaft position sensor performance test (P0366 for cam input 1, P0341 for cam input 2): the cam edges counted in each test window must fall within the band; when enough windows fall outside it the code sets, otherwise the test passes after a set number of windows. Effect: lower = a noisy cam signal with extra edges is flagged sooner Evidence: ledger:E1080, ledger:E1550</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D50" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>edges</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC9D" flags="0x30">
    <title>Cam Sensor Performance - Bad Windows to Fail</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Windows outside the band that set the code (stock 8). Camshaft position sensor performance test (P0366 for cam input 1, P0341 for cam input 2): the cam edges counted in each test window must fall within the band; when enough windows fall outside it the code sets, otherwise the test passes after a set number of windows. Effect: lower = the code sets after fewer bad windows Evidence: ledger:E1080, ledger:E1550</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D58" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>windows</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC9E" flags="0x30">
    <title>Cam Sensor Performance - Windows per Test</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Windows after which the test passes when fewer were bad (stock 10). Camshaft position sensor performance test (P0366 for cam input 1, P0341 for cam input 2): the cam edges counted in each test window must fall within the band; when enough windows fall outside it the code sets, otherwise the test passes after a set number of windows. Effect: raise = a longer test before a pass is reported Evidence: ledger:E1080, ledger:E1550</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D60" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>windows</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xC9F" flags="0x30">
    <title>Cam Sensor Performance - Window Length</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Length of one test window, in updates of the cam check, which runs with the crank position tasks (stock 1000). Camshaft position sensor performance test (P0366 for cam input 1, P0341 for cam input 2): the cam edges counted in each test window must fall within the band; when enough windows fall outside it the code sets, otherwise the test passes after a set number of windows. Effect: raise = longer windows, more edges per window (the band must be scaled with it) Evidence: ledger:E1080, ledger:E1550</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D68" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>updates</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xCA0" flags="0x0">
    <title>EVAP Test (Engine Running) - Wait Before Leak Check</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After the purge valve check, the engine-running EVAP test waits at least this long (with purge enabled and the purge factor above the required value) before it starts the leak pull-down. 0 = start at once when purge is already enabled. Stock 5 s. Effect: raise = the leak check starts later after the purge valve check Evidence: ledger:E1551</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3585E" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCA1" flags="0x0">
    <title>EVAP Test (Engine Running) - Purge Factor Required for Leak Check</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The engine-running EVAP test starts its leak pull-down only once the canister purge factor (1.0 = full purge request) has reached this. Stock 0.5. Effect: raise = the leak check waits for more purge first Evidence: ledger:E1551</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3585A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCA2" flags="0x0">
    <title>EVAP Test (Engine Running) - Time Allowed After Gross Leak Pass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the tank reaches the gross leak pass vacuum, the engine-running EVAP test may go on (vent check and the rest) for this long; after it the test stops for the rest of the trip. A failed gross leak check stops it at once. Stock 90 s. Effect: raise = the test gets longer to finish its remaining checks after the pull-down Evidence: ledger:E1552</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3586A" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xCA3" flags="0x30">
    <title>Cam Sensor Start-Up Check - Window Length</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Length of the start-up check window, in updates of the cam check counted from the arming update (stock 10). Camshaft position sensor start-up check (P0366 for cam input 1, P0341 for cam input 2): once armed, the cam edges counted in one window must fall within the band, otherwise the code sets; inside the band the check passes. It runs once. Effect: raise = a longer window, more edges expected (the band must be scaled with it) Evidence: ledger:E1080, ledger:E1553</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D06" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>updates</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xCA4" flags="0x30">
    <title>Cam Sensor Start-Up Check - Minimum Edges</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fewest cam edges in the window that pass (stock 4 / 2). Camshaft position sensor start-up check (P0366 for cam input 1, P0341 for cam input 2): once armed, the cam edges counted in one window must fall within the band, otherwise the code sets; inside the band the check passes. It runs once. Effect: raise = a cam signal that loses edges at start-up is flagged sooner Evidence: ledger:E1080, ledger:E1553</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D0E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>edges</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xCA5" flags="0x30">
    <title>Cam Sensor Start-Up Check - Maximum Edges</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most cam edges in the window that pass (stock 13 / 9). Camshaft position sensor start-up check (P0366 for cam input 1, P0341 for cam input 2): once armed, the cam edges counted in one window must fall within the band, otherwise the code sets; inside the band the check passes. It runs once. Effect: lower = a noisy cam signal at start-up is flagged sooner Evidence: ledger:E1080, ledger:E1553</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D16" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>edges</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xCA6" flags="0x30">
    <title>EVAP Test (Engine Running) - Pull-Down Time Allowance by Fuel Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time allowed in the test&#x27;s time budget for each pull-down, by fuel level (below 33 %, 33 to 67 %, above 67 %; the first when the fuel level reading is invalid). The test starts only if the time left covers its budget, and ends when the budget runs out. Stock 30 / 20 / 10 s. Engine-running EVAP test. Effect: raise = a longer budget (the test needs a longer window to start) Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>fuel level</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="below 33 %" />
      <LABEL index="1" value="33 to 67 %" />
      <LABEL index="2" value="above 67 %" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35862" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xCA7" flags="0x0">
    <title>EVAP Test (Engine Running) - Small Leak Decay Measurements</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of small leak decay measurements the test allows for; the time budget covers the ones still to go after the current one. Stock 3. Engine-running EVAP test. Effect: raise = a longer time budget Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E6A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCA8" flags="0x0">
    <title>EVAP Test (Engine Running) - Pull-Down Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the small leak pull-down must hold the tank between the pass vacuum and the pull-down maximum; also a term of the time budget for each measurement. Stock 10 s. Engine-running EVAP test. Effect: raise = a longer hold and budget Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E6C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCA9" flags="0x0">
    <title>EVAP Test (Engine Running) - Minimum Decay Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shortest decay time before a small leak decay is evaluated; also a term of the time budget for each measurement. Stock 5 s. Engine-running EVAP test. Effect: raise = a longer minimum decay and budget Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E6E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCAA" flags="0x0">
    <title>EVAP Test (Engine Running) - Pull-Down Give-Up Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the small leak pull-down may stay below the pass vacuum before it gives up. Stock 10 s. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35880" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCAB" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Vent-Down Vacuum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vapour check: after venting, tank vacuum must fall to this or below. Stock 2.0 inH2O. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35878" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCAC" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Vent-Down Time Limit (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vapour check: vacuum above the vent-down value for longer than this stops the test. Also a term of the time budget while the vapour check is pending. Stock 30 s. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E74" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCAD" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Settle Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vapour check: time at or below the vent-down vacuum before the pressure measurement stage. Also a budget term. Stock 15 s. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E76" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCAE" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Start Vacuum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vapour check: the pressure measurement starts once tank vacuum is below this (negative = pressure). Stock -0.4 inH2O (0.4 inH2O pressure). Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3587C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCAF" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Start Time Limit (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vapour check: if the start vacuum is not reached within this, the measurement is skipped. Also a budget term. Stock 30 s. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E72" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCB0" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Measurement Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vapour check: length of the pressure rise measurement. Also a budget term. Stock 30 s. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E70" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCB1" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Tracking Start (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vapour check: time into the measurement from which the peak pressure is tracked for the slope. Stock 25 s. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3587A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCB2" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Pressure Slope Limit (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vapour check: a tank pressure rise slope at or above this means too much fuel vapour, and the test stops. Stock 0.024 inH2O/s. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3586E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O/s</units>
    <decimalpl>3</decimalpl>
    <min>-8.000000</min>
    <max>7.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCB3" flags="0x0">
    <title>EVAP Test (Engine Running) - Gross Leak Volume Flow Deduction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Purge flow taken off the modelled purge flow before it is added up into the purged volume of the gross leak check (P0455 fails when the volume passes its limit before the tank reaches the pass vacuum). Stock 0 L/s. Engine-running EVAP test. Effect: raise = less volume counted per second (the gross leak check takes longer to fail) Evidence: ledger:E1555</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35882" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>L/s</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.124998</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/524288"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCB4" flags="0x0">
    <title>EVAP Test (Engine Running) - Decay Early Evaluation Vacuum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Small leak decay: evaluated before its full time once tank vacuum falls below this. Stock 1.0 inH2O. Engine-running EVAP test. Used only in the small leak decay of the engine-running test, which the stock option words skip, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1555</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35884" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCB5" flags="0x0">
    <title>EVAP Test (Engine Running) - Decay Limit Factor (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Small leak decay: multiplier on the decay slope limit from the limit tables. Stock 1.0. Engine-running EVAP test. Used only in the small leak decay of the engine-running test, which the stock option words skip, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1555</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35886" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCB6" flags="0x0">
    <title>EVAP Test (Engine Running) - Decay Measurement Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Small leak decay: time after which the decay slope is evaluated. Stock 10 s. Engine-running EVAP test. Used only in the small leak decay of the engine-running test, which the stock option words skip, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1555</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35888" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCB7" flags="0x0">
    <title>Fuel Tank Pressure - Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new fuel tank pressure sensor reading taken into the filtered tank vacuum used by the EVAP tests (and reported on the scan tool). Stock 0.2. Effect: lower = smoother, slower tank vacuum reading Evidence: ledger:E1556</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E7E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCB8" flags="0x0">
    <title>Fuel Tank Pressure - Change Check Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new tank pressure reading taken into the copy the tank pressure change check uses. Stock 0.3. Effect: lower = the change check sees smaller, slower changes Evidence: ledger:E1556</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E82" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCB9" flags="0x0">
    <title>Fuel Tank Pressure - Settle Time After Key-On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time after key-on before the tank pressure sensor zero is taken and the tank pressure filtering starts. Stock 0.1 s. Effect: raise = the zero is taken later after key-on Evidence: ledger:E1556</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E80" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCBA" flags="0x0">
    <title>Fuel Tank Pressure Change Check - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time before the tank pressure change check starts comparing changes with its limits. Stock 4 s. Effect: raise = the change check starts later Evidence: ledger:E1556</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E8A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCBB" flags="0x0">
    <title>Fuel Tank Pressure Change Check - Fuel Level When Sensor Invalid</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel level used to pick the tank pressure change limits when the fuel level reading is invalid. Stock 85 %. Effect: changes which change limits apply while the fuel level sensor is invalid Evidence: ledger:E1556</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35E8C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCBC" flags="0x0">
    <title>EVAP Re-Check - Moving Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Moving time (with purge at or above the purge minimum below) after which the re-check sets its vent request as when purge is off. Stock 60 s. EVAP gross leak re-check (runs on a later trip after a gross leak failure, P0455). Effect: raise = the re-check holds on for longer while driving Evidence: ledger:E1557</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F36" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCBD" flags="0x0">
    <title>EVAP Re-Check - Purge Minimum for Moving Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While driving, the re-check&#x27;s moving time and run time count only with commanded purge at or above this. Stock 20 %. EVAP gross leak re-check (runs on a later trip after a gross leak failure, P0455). Effect: raise = more purge needed before driving time counts Evidence: ledger:E1557</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F40" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCBE" flags="0x0">
    <title>EVAP Vent - Pulse Cycles at Test Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of vent pulse cycles the EVAP test runs when it takes control of the vent. Stock 2. Fuel tank vent solenoid, EVAP test control. Effect: raise = more vent pulses Evidence: ledger:E1559</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35ED6" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCBF" flags="0x0">
    <title>EVAP Vent - Pulse Cycle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Length of each vent pulse cycle at test start. Stock 0.4 s. Fuel tank vent solenoid, EVAP test control. Effect: raise = longer pulses Evidence: ledger:E1559</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35ED7" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCC0" flags="0x0">
    <title>EVAP Vent - Pulse Off Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of each vent pulse cycle with the vent command off; the rest of the cycle it is on. Stock 0.2 s. Fuel tank vent solenoid, EVAP test control. Effect: raise = longer off part of each pulse Evidence: ledger:E1559</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35ED8" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCC1" flags="0x0">
    <title>EVAP Vent On-Time - Vacuum Band Upper Limit (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank vacuum above this uses the third row of the vent on-time table. Stock 14 inH2O. Fuel tank vent solenoid, EVAP test control. Used only with the vent on-time option, which is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1559</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35EDC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCC2" flags="0x0">
    <title>EVAP Vent On-Time - Vacuum Band Lower Limit (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank vacuum at or below this uses the first row of the vent on-time table. Stock 12 inH2O. Fuel tank vent solenoid, EVAP test control. Used only with the vent on-time option, which is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1559</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35EDE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCC3" flags="0x0">
    <title>EVAP Vent On-Time - Fuel Level When Sensor Invalid (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel level used for the vent on-time table when the fuel level reading is invalid. Stock 40 %. Fuel tank vent solenoid, EVAP test control. Used only with the vent on-time option, which is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1559</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35EE0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCC4" flags="0x0">
    <title>EVAP Vent On-Time - Start Delay (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Delay before the vent on-time starts in the small leak pull-down. Stock 0 s. Fuel tank vent solenoid, EVAP test control. Used only with the vent on-time option, which is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1559</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35EE2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xCC5" flags="0x30">
    <title>EVAP Vent On-Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the vent command stays on, by tank vacuum band (rows) and fuel level (columns). Stock all 0. Fuel tank vent solenoid, EVAP test control. Used only with the vent on-time option, which is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1559</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>fuel level (%)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>tank vacuum band</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="up to 12 inH2O" />
      <LABEL index="1" value="12 to 14 inH2O" />
      <LABEL index="2" value="above 14 inH2O" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35EE6" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xCC6" flags="0x0">
    <title>EVAP Vapour Reference When Fuel Level Invalid</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vapour reference the EVAP test pull-down gain curves use when the fuel level reading is invalid (same scale as the vapour reference at full / empty tank, shown raw). Stock 15349. Effect: selects which pull-down gain points apply with a bad fuel level reading Evidence: ledger:E1560</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35876" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCC7" flags="0x0">
    <title>EVAP Service Test - Startup Coolant Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A scan-tool requested EVAP service test is refused when the coolant temperature at start-up was at or above this. Stock 70 C. Effect: raise = the service test is accepted after a warmer start Evidence: ledger:E1560</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3582C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCC8" flags="0x0">
    <title>EVAP Service Test - Vehicle Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A scan-tool requested EVAP service test is stopped when vehicle speed rises above this. Stock 16 km/h. Effect: raise = the service test tolerates more vehicle movement Evidence: ledger:E1560</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3582E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCC9" flags="0x0">
    <title>EVAP Vent - Scan Tool Command Tank Vacuum Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A scan-tool vent solenoid command is dropped while tank vacuum is above this. Stock 14 inH2O. Effect: raise = the tool can command the vent at higher tank vacuum Evidence: ledger:E1560</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35EDA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCCA" flags="0x0">
    <title>A/C Disable After Throttle Closes - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the throttle closes, the A/C compressor is kept from engaging for this time. It applies only while the compressor is not already engaged. Stock 2.0 s. Effect: raise = the compressor waits longer before it can engage after a lift-off Evidence: ledger:E1567</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x29014" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCCB" flags="0x0">
    <title>A/C Cut - High Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The A/C compressor is cut when engine speed stays above this for longer than the high speed delay, and it does not engage above it. Stock 6500 rpm. Effect: raise = the compressor keeps running at higher engine speed Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x208A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCCC" flags="0x0">
    <title>A/C Cut - Immediate Cut Margin, Park / Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the A/C high engine speed limit: above the sum the compressor is cut at once in Park or Neutral. Stock 500 rpm. Effect: raise = the instant high speed cut in Park / Neutral comes later Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x208AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCCD" flags="0x0">
    <title>A/C Cut - High Engine Speed Margin, In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the A/C high engine speed limit when in gear, for the delayed cut and for engagement. Stock 0 rpm. Effect: raise = in gear the compressor runs and engages at higher engine speed Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x208AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCCE" flags="0x0">
    <title>A/C Engage - High Engine Speed Hysteresis, In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In gear the compressor may engage only below the high engine speed limit (plus the in-gear margin) minus this. Stock 0 rpm. Effect: raise = engine speed must drop further below the limit before the compressor engages again Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x208AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCCF" flags="0x0">
    <title>A/C Engage - High Engine Speed Hysteresis, Park / Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In Park or Neutral the compressor may engage only below the high engine speed limit minus this. Stock 0 rpm. Effect: raise = engine speed must drop further below the limit before the compressor engages again Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x208B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCD0" flags="0x0">
    <title>A/C Cut - Immediate Cut Margin, In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the A/C high engine speed limit: above the sum the compressor is cut at once when in gear. Stock 500 rpm. Effect: raise = the instant high speed cut in gear comes later Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x208B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCD1" flags="0x0">
    <title>A/C Cut - Low Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The A/C compressor is cut when engine speed stays below this for longer than the low speed delay. Stock 400 rpm. Effect: raise = the compressor is cut at a higher engine speed in a low speed dip Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x208B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCD2" flags="0x0">
    <title>A/C Cut - Low Engine Speed Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long engine speed must stay below the A/C low engine speed limit before the compressor is cut. Stock 5.0 s. Effect: raise = a low engine speed is tolerated longer before the cut Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x208B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCD3" flags="0x0">
    <title>A/C Cut - High Engine Speed Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long engine speed must stay above the A/C high engine speed limit before the compressor is cut. Stock 5.0 s. Effect: raise = a high engine speed is tolerated longer before the cut Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x208B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCD4" flags="0x0">
    <title>A/C Engage - Low Engine Speed Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The compressor may engage only above the A/C low engine speed limit plus this. Stock 50 rpm. Effect: raise = engine speed must rise further above the low limit before the compressor engages Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x208BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCD5" flags="0x0">
    <title>Cam Phase Transient Detector - Cam Phase Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phase (actual retard from park) above which the airmass predictor&#x27;s cam phase transient detector starts tracking the excess. The excess above this value is filtered twice (fast and slow); a large gap between the two flags a cam phase transient, which switches the airmass predictor to its alternate blend row. Stock 7.0 deg. Effect: raise = cam phase must move further before transients are tracked; lower = tracking starts at less cam phase Evidence: ledger:E1277, ledger:E1572, ledger:E1574</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C5AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>deg</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xCD6" flags="0x30">
    <title>Cam Phase Transient Detector - Slow Lag Weight by Region</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the new cam phase excess (above the cam phase ceiling) taken into the slow filtered excess each update, by airmass predictor region. The detector compares this slow value with the fast one (fast weight: Cam and Volumetric Efficiency Deficit Blend Gain). Stock 0.09 to 0.26. Effect: higher = slow value follows faster, so a smaller gap and fewer transients flagged Evidence: ledger:E1277, ledger:E1572, ledger:E1574</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C5AE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xCD7" flags="0x30">
    <title>Cam Phase Transient Detector - Threshold by Region</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Gap between the fast and slow filtered cam phase excess at or above which a cam phase transient is flagged, by airmass predictor region. While flagged, the airmass predictor uses its alternate blend row. Stock 0.19 to 3.40 deg. Effect: raise = larger cam phase moves needed to flag a transient; 0 = always flagged Evidence: ledger:E1277, ledger:E1572, ledger:E1574</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C5D2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xCD8" flags="0x30">
    <title>Cam / Crank Correlation Test - Segment Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest crank segment (0..4) a cam pulse may fall in and pass (stock 2 on input 2). When the maximum is below the minimum the window wraps through segment 0. Crankshaft / camshaft position correlation test (P0017 for cam input 1, P0016 for cam input 2): on each new cam pulse the crank segment it falls in (0..4, one segment per 72 crank degrees, counted from the crank wheel&#x27;s missing-tooth reference) is checked against a window; too many samples outside the window set the code, enough samples pass it. On the stock calibration only input 2 runs; input 1&#x27;s values are zero and its test is switched off by its mode setting...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0017)" />
      <LABEL index="1" value="input 2 (P0016)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D26" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>segment</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xCD9" flags="0x30">
    <title>Cam / Crank Correlation Test - Segment Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest crank segment (0..4) a cam pulse may fall in and pass (stock 3 on input 2). Crankshaft / camshaft position correlation test (P0017 for cam input 1, P0016 for cam input 2): on each new cam pulse the crank segment it falls in (0..4, one segment per 72 crank degrees, counted from the crank wheel&#x27;s missing-tooth reference) is checked against a window; too many samples outside the window set the code, enough samples pass it. On the stock calibration only input 2 runs; input 1&#x27;s values are zero and its test is switched off by its mode setting. Effect: a wider window tolerates more cam / crank phase error before th...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0017)" />
      <LABEL index="1" value="input 2 (P0016)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D2E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>segment</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xCDA" flags="0x30">
    <title>Cam / Crank Correlation Test - Bad Samples to Fail</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam pulses outside the window that set the code before the pass count is reached (stock 8 on input 2). Crankshaft / camshaft position correlation test (P0017 for cam input 1, P0016 for cam input 2): on each new cam pulse the crank segment it falls in (0..4, one segment per 72 crank degrees, counted from the crank wheel&#x27;s missing-tooth reference) is checked against a window; too many samples outside the window set the code, enough samples pass it. On the stock calibration only input 2 runs; input 1&#x27;s values are zero and its test is switched off by its mode setting. Effect: lower = the code sets sooner on a misaligned...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0017)" />
      <LABEL index="1" value="input 2 (P0016)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D36" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xCDB" flags="0x30">
    <title>Cam / Crank Correlation Test - Samples to Pass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam pulses sampled before the test passes, if fewer than the fail count were outside the window (stock 10 on input 2). Crankshaft / camshaft position correlation test (P0017 for cam input 1, P0016 for cam input 2): on each new cam pulse the crank segment it falls in (0..4, one segment per 72 crank degrees, counted from the crank wheel&#x27;s missing-tooth reference) is checked against a window; too many samples outside the window set the code, enough samples pass it. On the stock calibration only input 2 runs; input 1&#x27;s values are zero and its test is switched off by its mode setting. Effect: raise = more samples needed...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0017)" />
      <LABEL index="1" value="input 2 (P0016)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D3E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xCDC" flags="0x30">
    <title>Cam Sensor Start-Up Check - Arming Segment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crank segment in which each cam input&#x27;s start-up check is armed once the crank is synced (stock 2 / 2); its window of updates starts there. The crank segment is 0..4, one segment per 72 crank degrees, counted from the crank wheel&#x27;s missing-tooth reference. Only the low byte of each word is compared. Effect: moves where the start-up check window starts; leave stock Evidence: ledger:E1080, ledger:E1579</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (exhaust)" />
      <LABEL index="1" value="input 2 (intake)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34CAC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>segment</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xCDD" flags="0x30">
    <title>Cam Sensor Performance - Arming Segment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crank segment in which each cam input&#x27;s performance test is armed (stock 2 / 2). The crank segment is 0..4, one segment per 72 crank degrees, counted from the crank wheel&#x27;s missing-tooth reference. Only the low byte of each word is compared. Effect: moves where the performance test windows start; leave stock Evidence: ledger:E1080, ledger:E1579</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (exhaust)" />
      <LABEL index="1" value="input 2 (intake)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34CB4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>segment</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xCDE" flags="0x0">
    <title>Cam Position Tests - Minimum MAP (Mode 1)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Manifold pressure the engine must be above before the cam position tests arm, for a cam input whose mode setting is 1 (stock 20 kPa). The stock calibration uses modes 0 / 2 on both inputs, so this value is not used. Effect: raise = the tests wait for more load (mode 1 only) Evidence: ledger:E1579</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34CC2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xCDF" flags="0x30">
    <title>Cam Angle Test - Cylinders Checked</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of cylinder cam angles the cam angle test checks against its angle window on each sample, per cam input (stock 5 / 5, one per cylinder). 0 skips the angle check for that input. Effect: leave stock: it must match the cylinder count Evidence: ledger:E1080, ledger:E1580</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (exhaust)" />
      <LABEL index="1" value="input 2 (intake)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D1E" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>cylinders</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xCE0" flags="0x0">
    <title>Cam Angle Learn - Filter Coefficient</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the difference between the measured cam angle and the learned cam angle that is taken into each cylinder&#x27;s learned angle per update (stock 0.25). Part of the per-cylinder cam angle learn, which runs above the per-cylinder learn minimum speed. Effect: raise = the learned angle follows faster Evidence: ledger:E1080, ledger:E1581</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23A84" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCE1" flags="0x0">
    <title>Cam Angle Deviation - Filter Coefficient</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter on the deviation of the measured cam angle from the learned angle, used by spark and fuel code (stock 0.999, nearly unfiltered). Part of the per-cylinder cam angle learn, which runs above the per-cylinder learn minimum speed. Effect: lower = a smoother, slower deviation signal Evidence: ledger:E1080, ledger:E1581</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23A86" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCE2" flags="0x0">
    <title>Cam Angle Learn - Reset Angle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam angle every cylinder&#x27;s measured, reported and learned angle is reset to (stock 53.1 deg). Part of the per-cylinder cam angle learn, which runs above the per-cylinder learn minimum speed. Effect: the starting point of the learn after a reset Evidence: ledger:E1080, ledger:E1581</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23A8E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>3</decimalpl>
    <min>-128.000000</min>
    <max>127.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCE3" flags="0x0">
    <title>Cam Phaser Stuck Response - Cam Angle Bad Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam angle test bad samples that start a stuck response (stock 3). Cam phaser stuck response, second trigger: when the exhaust cam angle test has counted enough bad samples, the PCM pulses the phaser solenoid as for a stuck cam, a limited number of times. Effect: lower = the response starts sooner Evidence: ledger:E0837, ledger:E1582</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22C9A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCE4" flags="0x0">
    <title>Cam Phaser Stuck Response - Cam Angle Responses Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most stuck responses this trigger may start (stock 3). Cam phaser stuck response, second trigger: when the exhaust cam angle test has counted enough bad samples, the PCM pulses the phaser solenoid as for a stuck cam, a limited number of times. Effect: raise = more retries Evidence: ledger:E0837, ledger:E1582</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22C9C" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>responses</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCE5" flags="0x0">
    <title>Cam Phaser Stuck Response - Cam Angle Pulse Repeats</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pulses one stuck response from this trigger gets (stock 6; the other trigger uses its own count, stock 12). Cam phaser stuck response, second trigger: when the exhaust cam angle test has counted enough bad samples, the PCM pulses the phaser solenoid as for a stuck cam, a limited number of times. Effect: raise = longer response Evidence: ledger:E0837, ledger:E1582</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22C9E" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCE6" flags="0x0">
    <title>Cranking Run Flag - Run Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at or above which the run flag counts toward setting (stock 550 rpm). Run flag of the cranking control: it sets once the engine has stayed at or above the run speed, and clears once it has stayed at or below the stop speed, each for a number of 25 ms updates. Effect: the speed that counts as running Evidence: ledger:E1583</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2D0D6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCE7" flags="0x0">
    <title>Cranking Run Flag - Stop Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at or below which the run flag counts toward clearing (stock 250 rpm). Run flag of the cranking control: it sets once the engine has stayed at or above the run speed, and clears once it has stayed at or below the stop speed, each for a number of 25 ms updates. Effect: the speed that counts as stopped Evidence: ledger:E1583</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2D0D8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCE8" flags="0x0">
    <title>Cranking Run Flag - Run Updates</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 25 ms updates counted at the run speed before the flag sets; it sets on the next update (stock 4). Run flag of the cranking control: it sets once the engine has stayed at or above the run speed, and clears once it has stayed at or below the stop speed, each for a number of 25 ms updates. Effect: raise = the run flag sets later Evidence: ledger:E1583</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2D0DA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCE9" flags="0x0">
    <title>Cranking Run Flag - Stop Updates</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 25 ms updates counted at the stop speed before the flag clears; it clears on the next update (stock 2). Run flag of the cranking control: it sets once the engine has stayed at or above the run speed, and clears once it has stayed at or below the stop speed, each for a number of 25 ms updates. Effect: raise = the run flag clears later Evidence: ledger:E1583</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2D0DC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCEA" flags="0x0">
    <title>Secondary Air - Ignition Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With the engine running, ignition voltage below this for longer than the low voltage time stops secondary air for the rest of the trip. Stock 10.0 V. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (raise = secondary air drops out on a weaker battery) Evidence: ledger:E1640</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA04" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCEB" flags="0x0">
    <title>Secondary Air - Low Voltage Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long ignition voltage must stay below the minimum before secondary air is stopped. Stock 5.0 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (raise = tolerates a longer voltage dip) Evidence: ledger:E1640</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA06" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCEC" flags="0x0">
    <title>Secondary Air - Delay After Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine run time before secondary air may turn on. Stock 0.5 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (raise = air pump starts later after the engine starts) Evidence: ledger:E1640</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA1A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCED" flags="0x0">
    <title>Secondary Air - Low MAP Suspend, Resume Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A low MAP suspend ends when manifold pressure rises above this. Stock 25 kPa. The suspend avoids exhaust popping on overrun. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1640</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA1C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCEE" flags="0x0">
    <title>Secondary Air - Low MAP Suspend, Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Secondary air is suspended when manifold pressure stays below this for the low MAP suspend time. Stock 20 kPa. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (raise = suspends at lighter load) Evidence: ledger:E1640</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA1E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCEF" flags="0x0">
    <title>Secondary Air - Low MAP Suspend Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long manifold pressure must stay below the suspend pressure before secondary air is suspended. Stock 2.0 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1640</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA20" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCF0" flags="0x0">
    <title>Secondary Air - High Airflow Suspend, Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Secondary air is suspended when engine airflow stays above this for the high airflow suspend time. Stock 50 g/s. The suspend keeps exhaust from pushing back into the air system. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1640</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA22" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCF1" flags="0x0">
    <title>Secondary Air - High Airflow Suspend, Resume Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A high airflow suspend ends when engine airflow drops below this. Stock 45 g/s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1640</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA24" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCF2" flags="0x0">
    <title>Secondary Air - High Airflow Suspend Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long airflow must stay above the suspend airflow before secondary air is suspended. Stock 3.0 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1640</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA26" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCF3" flags="0x0">
    <title>Secondary Air - High RPM Suspend, Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Secondary air is suspended above this engine speed. Stock 5000 rpm. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1640</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA28" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCF4" flags="0x0">
    <title>Secondary Air - High RPM Suspend, Resume Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A high speed suspend ends below this engine speed. Stock 4500 rpm. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1640</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA2A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCF5" flags="0x0">
    <title>Secondary Air - Minimum Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. If the run time from the run time vs catalyst temperature curve is below this, the pump does not run at all. Stock 0 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1640</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA36" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCF6" flags="0x0">
    <title>Secondary Air - Minimum Fuel Correction Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. If the fuel correction time from its curve is below this, no fuel correction is applied. Stock 0 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1640</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA38" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCF7" flags="0x0">
    <title>Cruise Control - Resume Ignore Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a resume, further resume / accel presses are ignored until the switch has been released for this long. Stock 1.5 s. Cruise control, resume / accel switch. Effect: lower = a second press acts sooner after a resume Evidence: ledger:E1644</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21E96" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCF8" flags="0x0">
    <title>Cruise Control - Accelerate From Standby Below Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Resume from standby: if vehicle speed minus set speed is below this, cruise accelerates back to the set speed; otherwise it resumes normally. Stock 0 km/h. Cruise control, resume / accel switch. Effect: usually left at 0 Evidence: ledger:E1644</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21EC8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCF9" flags="0x0">
    <title>Cruise Control - Tap Up Window, Speed Error Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A tap up raises the set speed only while vehicle speed minus set speed is at or above this. Stock -16 km/h. Cruise control, resume / accel switch. Effect: lower = tap ups count while further below the set speed Evidence: ledger:E1644</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21ECA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCFA" flags="0x0">
    <title>Cruise Control - Tap Up Window, Speed Error Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A tap up raises the set speed only while vehicle speed minus set speed is below this. Also, when the accel switch is released with the truck this far or more above the set speed, the current speed becomes the new set speed. Stock 16 km/h. Cruise control, resume / accel switch. Effect: raise = tap ups count further above the set speed Evidence: ledger:E1644</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21ECC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCFB" flags="0x0">
    <title>Cruise Control - Coast Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While the set / coast switch is held, the speed demand ramps down at this rate (negative). Stock -6.0 km/h/s. Cruise control demand register: the speed change still to be applied, worked off every 100 ms. Rate in km/h per second. Effect: more negative = coasts down faster while the switch is held Evidence: ledger:E1645</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21EC2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h/s</units>
    <decimalpl>2</decimalpl>
    <min>-2560.000000</min>
    <max>2559.921875</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/12.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCFC" flags="0x0">
    <title>Cruise Control - Tap Ramp Rate, Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rate at which a tap&#x27;s speed change is applied while the controller is inside its hysteresis band. Stock 1.0 km/h/s. Cruise control demand register: the speed change still to be applied, worked off every 100 ms. Rate in km/h per second. Effect: raise = taps take effect faster near the set speed Evidence: ledger:E1645</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21EC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h/s</units>
    <decimalpl>2</decimalpl>
    <min>-2560.000000</min>
    <max>2559.921875</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/12.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCFD" flags="0x0">
    <title>Cruise Control - Tap Ramp Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rate at which a tap up or tap down speed change is applied. Stock 2.0 km/h/s. Cruise control demand register: the speed change still to be applied, worked off every 100 ms. Rate in km/h per second. Effect: raise = the truck reaches a tapped speed sooner Evidence: ledger:E1645</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21EC6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h/s</units>
    <decimalpl>2</decimalpl>
    <min>-2560.000000</min>
    <max>2559.921875</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/12.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCFE" flags="0x0">
    <title>Cruise Control - Overspeed Disengage Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise disengages when the truck is this far above the set speed (allowing for any speed change still being applied); a set / coast press at this overspeed, with both switches released long enough before it, also disengages instead of tapping down. Stock 230 km/h, which never happens, so this is off on stock. Cruise control. Effect: lower (for example 8 km/h) = cruise drops out when the truck runs well over the set speed, such as downhill Evidence: ledger:E1647</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21EAA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCFF" flags="0x0">
    <title>Cruise Control - Overspeed Coast Press, Switches Released Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A set / coast press only disengages at overspeed if both cruise switches had been released for at least this long before it. Stock 3.0 s. Cruise control. Effect: only matters when the overspeed disengage error is lowered Evidence: ledger:E1647</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21E94" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD00" flags="0x0">
    <title>Cruise Control - Switch Hold Time to Reset Set Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a held cruise switch (resume / accel or set / coast) is released: if it was held at least this long, or the truck is below the set speed, the current speed becomes the new set speed; a shorter press with the truck at or above the set speed keeps the set speed. Stock 1.5 s. Cruise control. Effect: lower = shorter holds already re-set the cruise speed Evidence: ledger:E1648</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21E8E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD01" flags="0x0">
    <title>Dwell - Run Dwell Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the running dwell follows the dwell target, as the fraction of the gap closed every 12.5 ms update. Stock 0.99, so the dwell follows almost at once. Cranking dwell is not filtered. Effect: lower = dwell changes more slowly (smoother, but lags behind voltage and speed changes) Evidence: ledger:E1649</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2FA84" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD02" flags="0x0">
    <title>Misfire Similar Conditions - Cold Band, Coolant At or Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper edge of the cold coolant band. Stock 80 C (an OBD requirement). Misfire similar conditions: a stored misfire record and the current conditions count as similar only if engine speed and load are close and the coolant is in the same band (both in the cold band, or both in the warm band). Effect: emissions rule value: leave at stock Evidence: ledger:E1650</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3331A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD03" flags="0x0">
    <title>Misfire Similar Conditions - Warm Band, Coolant At or Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower edge of the warm coolant band. Stock 70.25 C (70 C per OBD). Misfire similar conditions: a stored misfire record and the current conditions count as similar only if engine speed and load are close and the coolant is in the same band (both in the cold band, or both in the warm band). Effect: emissions rule value: leave at stock Evidence: ledger:E1650</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3331C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD04" flags="0x0">
    <title>Vehicle Bus - Cruise Set Speed Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Change in the cruise set speed that triggers a new send of its message. Stock 1.0 km/h. Vehicle bus (serial data to the other modules): the message is sent again once at least the minimum interval has passed since it was last sent and the value has changed by at least the change threshold (or a status in it changed). Effect: lower = the set speed is reported in finer steps Evidence: ledger:E1676</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x202B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD05" flags="0x0">
    <title>Vehicle Bus - Cruise Set Speed Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum time between two sends of the cruise set speed message. Stock 0.3 s. Vehicle bus (serial data to the other modules): the message is sent again once at least the minimum interval has passed since it was last sent and the value has changed by at least the change threshold (or a status in it changed). Effect: lower = sent more often Evidence: ledger:E1676</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x202B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD06" flags="0x0">
    <title>Input Speed Sensor No Signal Check Enable (P0717)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the input (turbine) speed sensor no signal check on or off. 1: the PCM runs the check and can set P0717. 0: the check never runs, so P0717 is never set and never reported as passed. Stock 0 (off). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0717 check off (never set); 1 = check on Evidence: ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F7F8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD07" flags="0x0">
    <title>PCM Shutdown - Power Mode Off Time Before Shutdown</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the system power mode must stay off before the PCM is allowed to shut itself down. Effect: longer keeps the PCM awake longer after key off Evidence: ledger:E0435, ledger:E1764</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20916" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD08" flags="0x0">
    <title>Vehicle Bus - Transmission Status Message Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shortest time between two sends of one of the transmission status messages on the vehicle bus. Effect: bus timing: leave at stock Evidence: ledger:E1764</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x20966" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD09" flags="0x0">
    <title>Throttle - Battery Saver Inactivity Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time with the engine off and no pedal activity after which the throttle control goes to its battery saver state. Effect: longer keeps the throttle powered longer Evidence: ledger:E0592, ledger:E0923, ledger:E1764</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x24D68" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD0A" flags="0x0">
    <title>Spark - Medium Resolution Calculation Minimum RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at or above which the spark code switches to its modified medium resolution calculation. Effect: leave at stock Evidence: ledger:E1764</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2CE0C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD0B" flags="0x0">
    <title>Throttle Position - Learned Minimum, Highest Allowed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest value the learned closed-throttle position may take. Effect: leave at stock Evidence: ledger:E0420, ledger:E1764</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31372" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD0C" flags="0x0">
    <title>Throttle Position - Minimum Learn Extension Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time limit on extending the closed-throttle position learn; past it the learn stops. Effect: leave at stock Evidence: ledger:E1764</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31376" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD0D" flags="0x0">
    <title>Throttle Position - Minimum Learn Ignition Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest system voltage at which the closed-throttle position learn runs. Effect: leave at stock Evidence: ledger:E1764</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x3137C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD0E" flags="0x0">
    <title>Throttle Position - Minimum Learn MAP Limit While Cranking</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Manifold pressure limit that stops the closed-throttle position learn when it shows the engine is cranking or running. Effect: leave at stock Evidence: ledger:E1764</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31384" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD0F" flags="0x0">
    <title>Pedal Position - Learned Minimum Initial Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal position value used as the starting point of the learned pedal rest position. Effect: leave at stock Evidence: ledger:E1764</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31398" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD10" flags="0x0">
    <title>Secondary Air - Pump Off Test Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wait after the secondary air pump is shut off before the pump test starts. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: diagnostic timing Evidence: ledger:E0514, ledger:E1764</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3279C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD11" flags="0x0">
    <title>Secondary Air - Pump Off Test Maximum Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Longest the pump-off test may run before it ends. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: diagnostic timing Evidence: ledger:E0513, ledger:E1764</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x327A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD12" flags="0x0">
    <title>Secondary Air - Pump and Valve Minimum On Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum time the secondary air pump and valve must be on for the check to use the result. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: diagnostic timing Evidence: ledger:E0540, ledger:E0836, ledger:E1764</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x327A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD13" flags="0x0">
    <title>Secondary Air - Monitor Start Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Delay before the secondary air system is monitored. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: diagnostic timing Evidence: ledger:E0515, ledger:E0836, ledger:E1764</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x327A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD14" flags="0x0">
    <title>Secondary Air - Valve Test Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wait after the secondary air valve is switched before the valve test looks at the result. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: diagnostic timing Evidence: ledger:E0516, ledger:E0734, ledger:E1764</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x327AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD15" flags="0x0">
    <title>EVAP Small Leak Test - Minimum Fuel Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel level (share of tank capacity) at or above which the small leak EVAP test may run. Effect: diagnostic enable window Evidence: ledger:E0781, ledger:E1764</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3569C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD16" flags="0x0">
    <title>Misfire Diagnostic - Throttle Limit for Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle limit used to delay the misfire diagnostic (commanded throttle with the idle share removed). Effect: diagnostic enable window Evidence: ledger:E0772, ledger:E1764</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368D4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD17" flags="0x0">
    <title>Power Moding - Relay Delay Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Delay that makes sure the run / crank relay state has settled before the PCM acts on it. Effect: leave at stock Evidence: ledger:E0509, ledger:E1764</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x37524" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD18" flags="0x0">
    <title>EVAP Vapor Temp Sensor Circuit High Check Enable (P2027)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the EVAP fuel vapour temperature sensor circuit high check on or off. 1: the PCM runs the check and can set P2027. 0: the check never runs, so P2027 is never set and never reported as passed. Stock 0 (off). Effect: 0 = P2027 check off (stock); 1 = check on Evidence: ledger:E0437, ledger:E1765</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F46" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD19" flags="0x0">
    <title>EVAP Vapor Temp Sensor Circuit Low Check Enable (P2026)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the EVAP fuel vapour temperature sensor circuit low check on or off. 1: the PCM runs the check and can set P2026. 0: the check never runs, so P2026 is never set and never reported as passed. Stock 0 (off). Effect: 0 = P2026 check off (stock); 1 = check on Evidence: ledger:E0437, ledger:E1765</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F48" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD1A" flags="0x0">
    <title>Intake Air Temp Sensor Circuit Checks Enable (P0112 / P0113 / P1111 / P1112)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the intake air temperature sensor circuit checks on or off. 1: the PCM runs the low and high circuit checks and can set P0112, P0113, P1111 and P1112. 0: these checks never run. Stock 1 (on). Use 0 only when the sensor is not fitted. Effect: 0 = IAT circuit checks off (never set); 1 = checks on (stock) Evidence: ledger:E0437, ledger:E1765</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36548" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD1B" flags="0x0">
    <title>EVAP Engine-Off Leak Test Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the engine-off EVAP leak test on or off. 1: the test may run after key off when its conditions are met (fuel level window and the other enable limits). 0: the engine-off test never runs. Stock 1 (on). Effect: 0 = engine-off EVAP test off; 1 = on (stock) Evidence: ledger:E0769, ledger:E1765</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD1C" flags="0x0">
    <title>Secondary Air Diagnostic Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the secondary air system diagnostic on or off. 1: the pump and valve checks run when secondary air runs. 0: they never run. Stock 0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: 0 = secondary air checks off (stock); 1 = on Evidence: ledger:E0518, ledger:E1765</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3278A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD1D" flags="0x0">
    <title>Crank Signal Filter - Update While Running</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Selects whether the crank signal noise filter time is refreshed from its rpm curve while the engine runs (1) or only set at start (0). Stock 1. Effect: leave at stock Evidence: ledger:E0324, ledger:E1274, ledger:E1765</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x23AE8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = updated while running, 0 = set at start only</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD1E" flags="0x0">
    <title>Secondary Air - Run Time From Key-On Catalyst Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Selects how the secondary air run time and fuel correction time are chosen. 1: from the key-on catalyst temperature curves. 0: from the power-up coolant temperature (the fallback cold / warm times). Stock 1. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: leave at stock Evidence: ledger:E0436, ledger:E1765</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA18" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = catalyst temperature, 0 = coolant</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD1F" flags="0x0">
    <title>Throttle Position Sensor 1 - Voltage Direction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sets how the throttle position sensor 1 voltage is turned into throttle position. 1: the reading is used as is (voltage rises as the throttle opens). 0: the reading is mirrored (full scale minus the reading, voltage falls as the throttle opens). Stock 0. Must match the throttle body fitted; a wrong setting gives throttle faults. Effect: leave at stock unless the throttle body is changed Evidence: ledger:E0764, ledger:E1768</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x3138E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = as read, 0 = mirrored</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD20" flags="0x0">
    <title>Throttle Position Sensor 2 - Voltage Direction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sets how the throttle position sensor 2 voltage is used. 1: the reading is used as is. 0: the reading is mirrored (full scale minus the reading). Stock 1. Must match the throttle body fitted; a wrong setting gives throttle faults. Effect: leave at stock unless the throttle body is changed Evidence: ledger:E1768</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x3137A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = as read, 0 = mirrored</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD21" flags="0x0">
    <title>Purge in Open Loop - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Allows EVAP purge before closed loop. 1: after start the PCM picks the cold or warm run time delay by the start-up coolant split and allows open loop purge once the engine has run that long. 0: open loop purge is never allowed and the delay values have no effect. Stock 0 (off). Effect: 1 allows purge in open loop after the delay Evidence: ledger:E0781, ledger:E1768</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2534C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD22" flags="0x0">
    <title>Rear O2 Trim - Single Region Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Selects how the rear O2 trim region is chosen. 0: the region is picked from airflow with the region boundary values. 1: the first region is always used and the boundaries are ignored. Stock 0. Effect: leave at stock Evidence: ledger:E0380, ledger:E1768</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x257A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = single region, 0 = by airflow</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD23" flags="0x0">
    <title>A/C System Present</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tells the PCM whether A/C is fitted. 1: the A/C refrigerant pressure sensor is read and processed. 0: it is not. Stock 0. Effect: leave at stock unless the A/C is wired to the PCM Evidence: ledger:E1768</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20132" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD24" flags="0x0">
    <title>Transmission Type (1 = Automatic, 0 = Manual)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tells the PCM which gearbox is fitted. 0: the manual gearbox logic runs (gear worked out from engine speed and vehicle speed with the manual gear detection bands, transfer case low range ratio, shift lamp). 1: that logic is off (automatic). Stock 1. Effect: swap setting: 0 for a manual gearbox Evidence: ledger:E1768</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E98E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = automatic, 0 = manual</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD25" flags="0x0">
    <title>O2 Sensor Circuit Checks - Number of Upstream Sensors</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of upstream O2 sensors the PCM loops over in its O2 sensor checks. Each counted sensor gets its circuit check (the first one sets P0130). 0: the checks never run. Stock 1. Effect: leave at stock Evidence: ledger:E0437, ledger:E1768</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37450" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>sensors</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD26" flags="0x0">
    <title>Brake Switch B Check Enable (P0703)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the brake switch B handling and its circuit check on or off. 1: the PCM runs the check and can set P0703. 0: the check never runs, so P0703 is never set. Stock 0 (off). Effect: 0 = P0703 check off (stock); 1 = check on Evidence: ledger:E0434, ledger:E1768</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20162" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD27" flags="0x0">
    <title>EVAP Leak Test - Temperature Source Select</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Selects the temperature the EVAP small leak test logic uses. 1: ambient air temperature. 0: the lowest intake air temperature since start. With 1 the engine-running test also does not report P0442 from its small leak result. Stock 1. Effect: leave at stock Evidence: ledger:E0434, ledger:E1768, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35836" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = ambient air, 0 = intake air</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD28" flags="0x0">
    <title>EVAP Service Test Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Allows the EVAP service test that a scan tool can command. 1: the test may start when its conditions are met (engine not running, start-up coolant limit and the other checks). 0: the request is always refused. Stock 1. Effect: 0 = service test refused; 1 = allowed (stock) Evidence: ledger:E1768</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3582A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD29" flags="0x0">
    <title>Spark - Medium Resolution Calculation Maximum RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed below which the spark code uses its modified medium resolution calculation; it runs only above the minimum RPM and below this maximum. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: leave at stock Evidence: ledger:E0436, ledger:E1769</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2CE0E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD2A" flags="0x0">
    <title>Throttle Position - Learned Minimum Default Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-throttle position value both throttle position sensors&#x27; learned minimums are set to when the learn is reset. Effect: leave at stock Evidence: ledger:E1769</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31370" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD2B" flags="0x0">
    <title>Throttle Position - Minimum Learn Engine Turning RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed above which the PCM times the engine as turning. Once that time passes its limit, the closed-throttle position learn stops. Stock 50 rpm. Effect: leave at stock Evidence: ledger:E0436, ledger:E1769</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31380" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD2C" flags="0x0">
    <title>Throttle Position - Learned Minimum, Lowest Allowed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest value the learned closed-throttle position may take; a learned value below it is treated as out of range. Effect: leave at stock Evidence: ledger:E0436, ledger:E1769</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31386" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD2D" flags="0x0">
    <title>Throttle Position Sensor 2 - Full Travel Reading</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor 2 reading taken as full throttle travel. Sensor 2&#x27;s travel share is (reading minus its learned minimum) divided by (this value minus the learned minimum). Stock 88.4 %. Effect: leave at stock Evidence: ledger:E0436, ledger:E1769</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x3138A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD2E" flags="0x0">
    <title>Pedal Position - Learned Minimum Increase Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Amount added to the learned pedal rest position on each update while it is allowed to rise, up to the learned minimum initial value. Effect: leave at stock Evidence: ledger:E1769</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31396" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% per update</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD2F" flags="0x0">
    <title>Secondary Air - Low Pressure Bound Offset From Baro</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The low bound the secondary air pressure readings are compared with is barometric pressure plus this offset, floored at its minimum. Stock -10 kPa. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: diagnostic limit Evidence: ledger:E0621, ledger:E0799, ledger:E0804, ledger:E1769</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x326C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD30" flags="0x0">
    <title>Secondary Air - High Pressure Bound Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The high bound the secondary air pressure readings are compared with is barometric pressure plus a table offset, capped at this value. Stock 140 kPa. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: diagnostic limit Evidence: ledger:E0621, ledger:E0799, ledger:E0804, ledger:E1769</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x326C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD31" flags="0x0">
    <title>Secondary Air - Low Pressure Bound Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest value the low secondary air pressure bound (barometric pressure plus its offset) may take. Stock 40 kPa. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: diagnostic limit Evidence: ledger:E0621, ledger:E0799, ledger:E0804, ledger:E1769</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x326C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD32" flags="0x0">
    <title>Exhaust Model - Catalyst Channel Stored at Shutdown</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Selects which catalyst channel of the exhaust temperature model is stored at shutdown. The catalyst channels follow the oxygen sensor channels. Stock 0 (the first catalyst channel). Effect: leave at stock Evidence: ledger:E0776, ledger:E1769</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x33880" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>index (0 = first catalyst channel)</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD33" flags="0x0">
    <title>Fuel Tank Pressure - Engine-Off Test Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new tank vacuum reading taken into the filtered tank vacuum while the engine-off leak test logic selects it; otherwise the change check filter weight is used. Stock 0.05. Effect: lower = smoother, slower filtered tank vacuum Evidence: ledger:E1769</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34704" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD34" flags="0x0">
    <title>EVAP Engine-Off Test - Minimum System Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. System voltage at or below which the engine-off EVAP leak test does not run or is stopped. Stock 0 V (never blocks). Effect: diagnostic enable window Evidence: ledger:E0769, ledger:E1769</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3470A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD35" flags="0x0">
    <title>O2 Sensors - Number of Sensors</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of oxygen sensors the O2 sensor checks and the exhaust temperature model work through. Stock 2. Matches the fitted sensors: leave at stock. Effect: leave at stock Evidence: ledger:E0760, ledger:E1769</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x34784" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>sensors</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD36" flags="0x0">
    <title>EVAP Small Leak Test - Maximum Fuel Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel level (share of tank capacity) at or below which the small leak EVAP test may run. Effect: diagnostic enable window Evidence: ledger:E0781, ledger:E1769</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3569A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD37" flags="0x0">
    <title>EVAP Small Leak Test - Maximum Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed below which the small leak EVAP test&#x27;s enable timer runs; at or above it the timer is cleared. Stock 161 km/h. Effect: diagnostic enable window Evidence: ledger:E0781, ledger:E1769</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3569E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD38" flags="0x0">
    <title>Fuel Trim - Nominal Value (No Correction)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim value that means no correction; the long term fuel trims are reset to it. Stock 1.0. Effect: leave at stock Evidence: ledger:E0437, ledger:E1769</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x36290" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD39" flags="0x0">
    <title>MAP Sensor Circuit High Check Enable (P0108 / P1106)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the MAP sensor circuit high check on or off. 1: the PCM runs the check and can set P0108 and P1106. 0: the check never runs. Stock 1 (on). Effect: 0 = MAP circuit high check off; 1 = on (stock) Evidence: ledger:E1769</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36840" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD3A" flags="0x0">
    <title>MAP Sensor Circuit Low Check Enable (P0107 / P1107)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the MAP sensor circuit low check on or off. 1: the PCM runs the check and can set P0107 and P1107. 0: the check never runs. Stock 1 (on). Effect: 0 = MAP circuit low check off; 1 = on (stock) Evidence: ledger:E1769</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36842" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD3B" flags="0x0">
    <title>Misfire - Abnormal Event Ratio Check Disable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the misfire abnormal event ratio is held at 0 and never compared with its limit. 0: the ratio is worked out and checked against the abnormal event ratio limit. Stock 0 (check on). Effect: leave at stock Evidence: ledger:E0780, ledger:E1769</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3687E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check off, 0 = on</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD3C" flags="0x0">
    <title>Vehicle Acceleration - Moving Average Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new trans-side vehicle acceleration moving average value taken into its smoothed copy. Stock 0.98. Effect: lower = smoother, slower acceleration value Evidence: ledger:E1769</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF3C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xD3D" flags="0x30">
    <title>Cam Sensor Input Count (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of cam position sensor inputs the PCM services. Every per-cam-input loop (signal checks, cam sensor selection, cam diagnostics) runs this many times. Stock 2. Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0324, ledger:E1274, ledger:E1770</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>1</indexcount>
      <units>item</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="value" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23A04" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="1" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>cam inputs</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD3E" flags="0x30">
    <title>Cam Sensor Assigned to Each Cam Input (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cam sensor each cam input is treated as, which picks the trouble code that input&#x27;s checks look at: 0 = the P0340 sensor, 1 = the P0365 sensor, 2 = the P0345 sensor, 3 = the P0390 sensor. Stock 1, 0 (input 1 is the P0365 sensor, input 2 the P0340 sensor); the H3 has two cam inputs, so the third and fourth values are never used. Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0776, ledger:E1770</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input 1" />
      <LABEL index="1" value="cam input 2" />
      <LABEL index="2" value="cam input 3 (not fitted)" />
      <LABEL index="3" value="cam input 4 (not fitted)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34D70" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>cam sensor number</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD3F" flags="0x30">
    <title>Downstream O2 Sensor Count (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of downstream (after the catalyst) O2 sensors the PCM tests. The downstream sensor tests (P0136 and its voltage limits, one value per sensor) run for this many sensors. Stock 1. Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E1770</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>1</indexcount>
      <units>item</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="value" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37476" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="1" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>downstream O2 sensors</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD40" flags="0x30">
    <title>Response-Tested O2 Sensor Count (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of upstream O2 sensors that get the response tests (P0133 slow response, P1133 switching). Each listed sensor is checked once per pass. Stock 1. Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0437, ledger:E1770</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>1</indexcount>
      <units>item</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="value" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34756" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="1" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>O2 sensors</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD41" flags="0x30">
    <title>O2 Sensor List - Sensor Numbers (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensors the PCM has, as a list the response and heater tests pick from. Each value is a sensor number, which selects that sensor&#x27;s trouble codes. Sensor numbers: 0 = bank 1 sensor 1, 1 = bank 1 sensor 2, 2 = bank 1 sensor 3, 3 = bank 2 sensor 1, 4 = bank 2 sensor 2; 5 has no codes (filler). Stock 0, 1, 5, 5 (bank 1 sensor 1 and bank 1 sensor 2; the last two entries are not used by the stock lists). Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0437, ledger:E1561, ledger:E1770</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>list entry</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="entry 1" />
      <LABEL index="1" value="entry 2" />
      <LABEL index="2" value="entry 3" />
      <LABEL index="3" value="entry 4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3472A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>O2 sensor number</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD42" flags="0x30">
    <title>Response-Tested O2 Sensors - List Entries (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. For each upstream O2 sensor that gets the response tests (P0133, P1133), which entry of the O2 sensor list it is (0 = first entry). Stock 0 (the first entry, bank 1 sensor 1); the second value is not used because the count is 1. Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0437, ledger:E1770</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="response-tested sensor 1" />
      <LABEL index="1" value="response-tested sensor 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34732" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>O2 sensor list entry (0 = first)</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD43" flags="0x30">
    <title>Heated O2 Sensors - List Entries (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. For each heated O2 sensor whose heater is checked (P0135, P0141, P0155, P0161), which entry of the O2 sensor list it is (0 = first entry). Stock 0, 1 (bank 1 sensor 1 and bank 1 sensor 2); the PCM checks two heaters, so the third and fourth values are not used. Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0437, ledger:E1770</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="heated sensor 1" />
      <LABEL index="1" value="heated sensor 2" />
      <LABEL index="2" value="heated sensor 3 (not used)" />
      <LABEL index="3" value="heated sensor 4 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34736" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>O2 sensor list entry (0 = first)</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD44" flags="0x30">
    <title>Injector Pulse Width Group by Cylinder (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Which computed pulse width group each cylinder&#x27;s injector takes its pulse width from. Stock 0 for every cylinder (all cylinders use the first group). The array has room for eight cylinders; the H3 has five, so the last three values are never used. Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0436, ledger:E1770</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>cylinder</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cylinder 1" />
      <LABEL index="1" value="cylinder 2" />
      <LABEL index="2" value="cylinder 3" />
      <LABEL index="3" value="cylinder 4" />
      <LABEL index="4" value="cylinder 5" />
      <LABEL index="5" value="cylinder 6 (not fitted)" />
      <LABEL index="6" value="cylinder 7 (not fitted)" />
      <LABEL index="7" value="cylinder 8 (not fitted)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26038" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>pulse width group (0 = first)</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD45" flags="0x30">
    <title>Misfire Diagnostic - Cylinder Number by Slot (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cylinder number the misfire diagnostic gives each of its cylinder slots (the slots follow the firing order). It is used for the cylinder it reports and to find the slot of a given cylinder. Stock 4, 2, 1, 3, 5: the firing order 1, 3, 5, 4, 2 starting at cylinder 4. The last three values are not used on five cylinders. Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0780, ledger:E1770</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>misfire slot</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="slot 1" />
      <LABEL index="1" value="slot 2" />
      <LABEL index="2" value="slot 3" />
      <LABEL index="3" value="slot 4" />
      <LABEL index="4" value="slot 5" />
      <LABEL index="5" value="slot 6 (not used)" />
      <LABEL index="6" value="slot 7 (not used)" />
      <LABEL index="7" value="slot 8 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36880" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>cylinder #</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD46" flags="0x30">
    <title>Vehicle Bus - Module Lost Communication Check Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. One switch per vehicle bus module the PCM listens for. 1: the PCM runs the check on that module&#x27;s messages and can set or pass its U code (U1041, U1056, U1064, U1065, U1066, U1088, U1096, U1152, U1192 in this order). 0: the check never reports, so that code is never set. Stock on for U1041, U1064 and U1096, off for the rest. Turn a module off only when it is not on the vehicle (for example in an engine swap). Effect: 0 = that module&#x27;s U code is never set; 1 = check on Evidence: ledger:E0435, ledger:E1770</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>bus module (by its code)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="module U1041" />
      <LABEL index="1" value="module U1056" />
      <LABEL index="2" value="module U1064" />
      <LABEL index="3" value="module U1065" />
      <LABEL index="4" value="module U1066" />
      <LABEL index="5" value="module U1088" />
      <LABEL index="6" value="module U1096" />
      <LABEL index="7" value="module U1152" />
      <LABEL index="8" value="module U1192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20900" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>1 = check on, 0 = off</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD47" flags="0x30">
    <title>Catalyst Monitor - Rich Step First Select</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: selects the order of the fuel steps for the O2 switch points. 1: the test starts with its rich step, and the rich step switch voltages are used. 0: it starts with a lean step, and the lean first switch voltages are used. Stock 1. Effect: leave at stock Evidence: ledger:E0676, ledger:E1770</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x329B4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>1 = rich step first, 0 = lean first</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xD48" flags="0x0">
    <title>Brake Torque Limit - Release Step (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the brake torque limit ends, the engine torque limit it set is raised by this amount on each update of its ramp-out phase. Stock 0.5 Nm. The brake torque limit table is at its maximum (no limit) in every cell on the stock calibration, so this has no effect on the stock calibration (dormant). Effect: raise = the torque limit is released faster Evidence: ledger:E0436, ledger:E1771</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2183C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm per update</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD49" flags="0x0">
    <title>Brake Torque Limit - Engine Vacuum Offset (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the filtered engine vacuum before it is used as the vacuum input of the brake torque limit table. Stock 0.2 kPa. The brake torque limit table is at its maximum (no limit) in every cell on the stock calibration, so this has no effect on the stock calibration (dormant). Effect: leave at stock Evidence: ledger:E0436, ledger:E1771</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2183E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD4A" flags="0x0">
    <title>Brake Torque Limit - Engine Vacuum Filter, Falling (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lag filter on the engine vacuum used by the brake torque limit, while vacuum is falling or steady: each update moves the filtered value this fraction of the way to the new reading. Stock 0.10. The brake torque limit table is at its maximum (no limit) in every cell on the stock calibration, so this has no effect on the stock calibration (dormant). Effect: lower = the filtered vacuum follows a falling vacuum more slowly Evidence: ledger:E0436, ledger:E1771</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21840" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD4B" flags="0x0">
    <title>Brake Torque Limit - Engine Vacuum Filter, Rising (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lag filter on the engine vacuum used by the brake torque limit, while vacuum is rising: each update moves the filtered value this fraction of the way to the new reading. Stock 0.10. The brake torque limit table is at its maximum (no limit) in every cell on the stock calibration, so this has no effect on the stock calibration (dormant). Effect: lower = the filtered vacuum follows a rising vacuum more slowly Evidence: ledger:E0436, ledger:E1771</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21842" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD4C" flags="0x0">
    <title>Brake Torque Limit - Driveline Ratio Share (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the overall driveline torque ratio used to turn the brake torque limit into an engine torque limit (engine limit = brake torque limit / (driveline ratio x this share)). Stock 50 %. The brake torque limit table is at its maximum (no limit) in every cell on the stock calibration, so this has no effect on the stock calibration (dormant). Effect: raise = lower engine torque limit for the same brake torque limit Evidence: ledger:E0436, ledger:E1771</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21844" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD4D" flags="0x0">
    <title>Cruise Control - Vehicle Acceleration Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: how fast the vehicle acceleration the cruise controller works from follows the measured change in vehicle speed, as the fraction of the gap closed per update. Stock 0.20. Effect: lower = the cruise acceleration signal is smoothed more (slower to react) Evidence: ledger:E0436, ledger:E1771</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21E88" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD4E" flags="0x0">
    <title>Cruise Control - Second-Order Acceleration Filter, Last Output Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of the previous filtered acceleration in the second-order cruise acceleration filter. Stock 0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: dormant on stock: leave at stock Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x222E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>-0.125000</min>
    <max>0.124996</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/262144"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD4F" flags="0x0">
    <title>Cruise Control - Second-Order Acceleration Filter, Output Two Updates Back Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of the filtered acceleration from two updates back in the second-order cruise acceleration filter. Stock 0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: dormant on stock: leave at stock Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x222E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>-0.125000</min>
    <max>0.124996</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/262144"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD50" flags="0x0">
    <title>Cruise Control - Second-Order Acceleration Filter, New Input Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of the new raw acceleration (vehicle speed change) in the second-order cruise acceleration filter. Stock 0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: dormant on stock: leave at stock Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x222EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>-0.125000</min>
    <max>0.124996</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/262144"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD51" flags="0x0">
    <title>Cruise Control - Second-Order Acceleration Filter, Last Input Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of the raw acceleration from the previous update in the second-order cruise acceleration filter. Stock 0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: dormant on stock: leave at stock Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x222EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>-0.125000</min>
    <max>0.124996</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/262144"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD52" flags="0x0">
    <title>Cruise Control - Second-Order Acceleration Filter, Input Two Updates Back Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of the raw acceleration from two updates back in the second-order cruise acceleration filter. Stock 0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: dormant on stock: leave at stock Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x222EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>-0.125000</min>
    <max>0.124996</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/262144"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD53" flags="0x0">
    <title>Low Oil Pressure Check - Recovery Margin (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With the oil pressure sensor path on: once oil pressure has been found below the minimum oil pressure for the engine speed, the low oil pressure state clears only when oil pressure is at or above that minimum plus this margin. Stock 25 kPa. The oil pressure sensor path is switched off in the stock calibration (Oil Pressure Sensor Path Enable = 0; the PCM uses its oil pressure estimate instead), so this has no effect on the stock calibration (dormant). Effect: raise = oil pressure must recover further before the low pressure state clears Evidence: ledger:E1771, ledger:E1831</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23160" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD54" flags="0x0">
    <title>Tip-In Spark Advance - Engine-Off Time Factor, Previous Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in spark advance: the engine-off time factor is applied to the advance only when the previous engine run lasted at least this long. Stock 60 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: leave at stock (dormant) Evidence: ledger:E0431, ledger:E1771</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2CD80" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD55" flags="0x0">
    <title>Airmass Model - Start-Up Blend Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During the start-up blend the load and fuel airmass move from the speed-density airmass to the capped prediction blend; each update the blend weight rises by this step until it reaches 1.0 (stock 0.10, so about 10 updates). Part of the cylinder airmass model; reference only, DO NOT EDIT. Effect: raise = the start-up blend completes in fewer updates Evidence: ledger:E0780, ledger:E0803, ledger:E1771</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C27C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD56" flags="0x0">
    <title>Spark - Medium Resolution Period Ratio Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inside the medium resolution engine speed window the spark timing code predicts the next crank period as the current period times the ratio of the current to the previous period; this is the lowest ratio allowed. Stock 1.0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: leave at stock Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2CE08" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD57" flags="0x0">
    <title>Spark - Medium Resolution Period Ratio Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inside the medium resolution engine speed window the spark timing code predicts the next crank period as the current period times the ratio of the current to the previous period; this is the highest ratio allowed. Stock 1.0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: leave at stock Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2CE0A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD58" flags="0x0">
    <title>Engine Speed Rate of Change - Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lag filter on the engine speed rate of change (the change in engine speed since the last update divided by the cylinder period): each update moves the filtered value this fraction of the way to the new value. Stock 0.50. Effect: lower = smoother, slower engine speed rate signal Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x23A52" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD59" flags="0x0">
    <title>Vehicle Speed - Distance Rolling Count Reset Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the PCM keeps the distance rolling count reset bit set in its vehicle speed and distance status data before clearing it, in whole seconds. The count only runs in two of the system power modes and restarts otherwise. Stock 1 s. Effect: leave at stock Evidence: ledger:E0486, ledger:E1772</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x2008A" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD5A" flags="0x0">
    <title>Generator Control - Low Speed Mode Cumulative Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The generator low engine speed mode is active while the engine runs below a speed limit taken from desired idle. Its time in that mode adds up; once the total passes this value the mode is turned off. Stock 100 s. Effect: leave at stock Evidence: ledger:E0608, ledger:E0923, ledger:E1772</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20844" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD5B" flags="0x0">
    <title>Theft Deterrent - Fuel Decision Minimum Time Since Power-Up</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The theft deterrent fuel decision step is ready only when the PCM has been powered for at least this long, the engine is running and the engine run time limit below is met. Stock 0.2 s. Effect: leave at stock Evidence: ledger:E1772</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20972" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD5C" flags="0x0">
    <title>Theft Deterrent - Fuel Decision Minimum Engine Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The theft deterrent fuel decision step is ready only when the engine has run for at least this long (together with the power-up time limit above). Stock 0 s. Effect: leave at stock Evidence: ledger:E1772</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20974" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD5D" flags="0x0">
    <title>Coolant Temp Sensor Failsoft - Maximum Substitute Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With a coolant temperature sensor fault, the PCM uses a substitute coolant temperature that rises a step at a time while the engine runs. This is the highest value the substitute rises to. Stock 40 degC. Effect: higher = the engine is treated as warmer after a long run with a failed sensor Evidence: ledger:E0776, ledger:E1772</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x22838" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD5E" flags="0x0">
    <title>Fuel Injector Purge - Start Delay (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Delay, once its conditions are met, before the injector purge sequence starts. The purge is not enabled for any cylinder in the stock calibration (per-cylinder enables all 0), so this has no effect on the stock calibration (dormant). Stock 0 s. Effect: leave at stock Evidence: ledger:E0436, ledger:E1772</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26682" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD5F" flags="0x0">
    <title>Fuel Temperature Model - Warm Restart Minimum Coolant Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At start-up the fuel temperature model compares the coolant temperature remembered from the previous run with this value. At or below it, the model starts from the present coolant temperature (cold start). Above it, the model takes its warm restart path. Stock 90 degC. Effect: leave at stock Evidence: ledger:E1384, ledger:E1772</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x28EDA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD60" flags="0x0">
    <title>Intake Air Temp Sensor Failsoft - Substitute Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intake air temperature the PCM uses in place of the sensor reading while the reading is out of range (circuit low or high). Stock 10 degC. Effect: used only with a failed intake air temperature sensor Evidence: ledger:E0436, ledger:E1772</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x290E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD61" flags="0x0">
    <title>Throttle Position - Minimum Learn Low Voltage Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long system voltage may stay below the minimum learn voltage before the closed-throttle position learn stops taking samples. Effect: leave at stock Evidence: ledger:E0436, ledger:E1772</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x3137E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD62" flags="0x0">
    <title>Throttle Position - Minimum Learn Engine Turning Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time engine speed must stay above the learn&#x27;s cranking speed limit before the closed-throttle position learn treats the engine as cranking or running. Effect: leave at stock Evidence: ledger:E0436, ledger:E1772</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31382" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD63" flags="0x0">
    <title>Throttle Position - Minimum Learn Time Limit With Engine Turning</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time limit on the closed-throttle position learn once the engine is cranking or running; past it the learn stops. Effect: leave at stock Evidence: ledger:E0436, ledger:E1772</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x3138C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD64" flags="0x0">
    <title>Secondary Air - Pump Off Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long after the secondary air pump request turns off the PCM keeps treating the pump as on. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: diagnostic timing Evidence: ledger:E0621, ledger:E0804, ledger:E0923, ledger:E1772</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x326DE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD65" flags="0x0">
    <title>EVAP Engine-Off Test - Minimum Fuel Vapor Temperature (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest fuel vapour temperature for the engine-off EVAP leak test to start. The temperature window is used only when the test&#x27;s temperature check enable is on; it is off in the stock calibration, so this has no effect on the stock calibration (dormant). Effect: diagnostic enable window Evidence: ledger:E0769, ledger:E1772</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345D8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD66" flags="0x0">
    <title>EVAP Engine-Off Test - Maximum Fuel Vapor Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel vapour temperature at or above which the engine-off EVAP leak test stops with a temperature abort (also the top of the start window when the temperature check enable is on). Stock about 256 degC (never reached). Effect: diagnostic enable window Evidence: ledger:E0769, ledger:E1772</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34708" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD67" flags="0x0">
    <title>EVAP Small Leak Test - Enable Conditions Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the small leak (0.020 inch) EVAP test enable conditions (fuel level window and the other limits) must hold before the test is allowed to run. Stock 15 s. Effect: diagnostic enable window Evidence: ledger:E0781, ledger:E1772</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x356A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD68" flags="0x0">
    <title>EVAP Leak Test - Valve Control Wait Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the EVAP leak test may wait in its valve control step before the wait is flagged as timed out. Stock 0.5 s. Effect: diagnostic timing Evidence: ledger:E0775, ledger:E1772</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35826" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD69" flags="0x0">
    <title>EVAP Vapor Temp Sensor Performance Check (P2025) - Minimum Engine-Off Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel vapour temperature sensor performance check (P2025) runs after a start only when the engine had been off for longer than this. Stock 540 s. Effect: diagnostic enable window Evidence: ledger:E0437, ledger:E1772</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35F76" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD6A" flags="0x0">
    <title>Watchdog - Background Task Stall Time Before Reset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the PCM&#x27;s background self-test loop may go without running before the PCM stops servicing its watchdog, which then resets the PCM. Stock 10 s. Effect: leave at stock Evidence: ledger:E0530, ledger:E1772</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x3754A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD6B" flags="0x0">
    <title>EVAP Running Leak Test - Samples Before Pass, Average 1 (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of leak samples the engine-running EVAP test must collect before its first leak average can be judged a pass. A fail can be set at any sample; only the pass waits for this count. Stock 6. The small leak phase of this test is skipped in the stock calibration (skip setting 1), so this has no effect on the stock calibration (dormant). Effect: more samples before a P0442 pass Evidence: ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x356C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD6C" flags="0x0">
    <title>EVAP Running Leak Test - Samples Before Pass, Average 2 (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of leak samples the engine-running EVAP test must collect before its second leak average (updated on every sample) can be judged a pass. Stock 6. The small leak phase of this test is skipped in the stock calibration (skip setting 1), so this has no effect on the stock calibration (dormant). Effect: more samples before a P0442 pass Evidence: ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x356CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD6D" flags="0x0">
    <title>EVAP Running Test - Skip Small Leak Phase</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the engine-running EVAP test never enters its small leak pull-down and decision phases, so it never sets P0442 from them. 0: after the gross leak phase the test moves on to the small leak phase, and its result can set P0442 (reporting also needs the leak test temperature source setting at 0). Stock 1 (skipped). Effect: 0 = small leak phase runs; 1 = skipped (stock) Evidence: ledger:E0434, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35832" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = skip, 0 = run</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD6E" flags="0x0">
    <title>EVAP Running Test - Vent On-Time Pull-Down Option</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 0: in both the gross leak and the small leak pull-downs the test drives purge from its vacuum pull-down controller. 1: the test does not take over purge during the gross leak pull-down; in the small leak pull-down purge is held at 0 and the vent is opened for the time from the vent on-time table. Stock 0. Effect: leave at stock Evidence: ledger:E0775, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35834" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = vent on-time, 0 = purge pull-down</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD6F" flags="0x0">
    <title>Fuel Trim Monitor - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the fuel trim monitor runs while the engine is running. 0: the monitor is held reset and never enabled. Stock 1. Effect: 0 = fuel trim monitor off; 1 = on (stock) Evidence: ledger:E0636, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3625A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD70" flags="0x0">
    <title>Misfire - Total Misfire Count Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the total misfire count rises above this value, with the misfire logic&#x27;s other conditions met, the PCM sets its excess misfire flag. Stock 100. Effect: diagnostic threshold Evidence: ledger:E0780, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37208" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xD71" flags="0x30">
    <title>Secondary Air - Number of Pressure Sensors</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of secondary air pressure sensors the PCM reads. 1: bank 1 only. 2: bank 1 and bank 2. 0: none. Stock 2. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: must match the fitted sensors Evidence: ledger:E0528, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>1</indexcount>
      <units>item</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="value" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x326C0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="1" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>sensors</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xD72" flags="0x0">
    <title>Secondary Air - Pressure Sensor Circuit Checks Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the PCM runs the secondary air pressure sensor circuit checks (P2432 / P2433 bank 1 low / high, P2437 / P2438 bank 2 low / high). 0: the checks never run. Stock 0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: 0 = checks off (stock); 1 = on Evidence: ledger:E0526, ledger:E0676, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3288E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD73" flags="0x0">
    <title>Secondary Air - Pressure Performance Checks Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the PCM runs the secondary air pressure performance checks (P2430 / P2435 circuit, P2431 / P2436 range / performance, bank 1 / bank 2) and uses the pressure bound settings. Other values: the checks never run. Stock 0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: 0 = checks off (stock); 1 = on Evidence: ledger:E0437, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x326A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, other = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xD74" flags="0x30">
    <title>Secondary Air - High Pressure Bound Above Baro</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to barometric pressure to give the high bound the secondary air pressure is checked against, capped by the high bound maximum. The second value applies while the pump is commanded on and during the pump off delay, the first once the pump is off. Stock 10 and 50 kPa. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: diagnostic threshold Evidence: ledger:E0437, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>pump state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="pump off" />
      <LABEL index="1" value="pump on or off delay" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3269E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD75" flags="0x30">
    <title>O2 Sensor Circuit Voltage Faults - Related Sensors Checked</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per O2 sensor: which related sensors&#x27; faults are checked before this sensor&#x27;s low or high voltage circuit fault (P0131 / P0137 low, P0132 / P0138 high) is reported. 1: the first related sensor only. 2: also the second related sensor list. If a checked related sensor is in its own fault condition, the report is held back. Stock 1, 1. Effect: leave at stock Evidence: ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>O2 sensor slot</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="slot 1" />
      <LABEL index="1" value="slot 2" />
      <LABEL index="2" value="slot 3 (not used)" />
      <LABEL index="3" value="slot 4 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34758" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>1 = one list, 2 = two lists</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xD76" flags="0x0">
    <title>Secondary Air - Hold Pump During Suspend</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: while secondary air is suspended (for example at high engine speed), the pump request stays as it was and the air valve switches at once without its on / off delays. 0: the normal pump and valve delay logic runs during suspend. Stock 0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: leave at stock Evidence: ledger:E0436, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2C9F8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD77" flags="0x0">
    <title>Torque Correction Loop - Output Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest correction, in either direction, that the torque correction loop may output. The loop output is clamped to plus or minus this value. Stock 100 Nm. Effect: leave at stock Evidence: ledger:E1774</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20A4E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD78" flags="0x0">
    <title>Torque Correction Loop - Peak Hold Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit on the held peak of the torque correction loop output. The torque reduction is measured down from this held peak. Stock 70 Nm. Effect: leave at stock Evidence: ledger:E0677, ledger:E1774</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20A52" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD79" flags="0x0">
    <title>Torque Correction Loop - Maximum Drop From Peak</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest drop from the held peak that is passed on. Beyond a small deadband (5 Nm stock) the drop is taken off the engine torque value the PCM uses in this calculation. Stock 100 Nm. Effect: leave at stock Evidence: ledger:E0677, ledger:E1774</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20A54" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD7A" flags="0x0">
    <title>Driver Pedal Throttle Area - Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: which transmission state uses this map is set by the item Pedal Map Select vs Trans State - Normal in this file; the stock selection on this calibration can differ from the H3 described below, so check that table on your own bin before editing this map. Upper limit on the throttle area requested from the accelerator pedal. Requests above it are held at this value. Stock 100 % (no limit). Effect: lower caps the pedal request Evidence: ledger:E0775, ledger:E1774</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x23EEA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD7B" flags="0x0">
    <title>EVAP Engine-Off Test - Fuel Temperature Window Check Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the engine-off EVAP leak test starts only when the fuel vapour temperature is between its minimum and maximum values, and an extra stability check runs while the result is evaluated. 0: the temperature window is ignored. Stock 0. Effect: 0 = window ignored (stock); 1 = window applies Evidence: ledger:E0434, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD7C" flags="0x0">
    <title>Fuel Injector Purge - Number of Pulse Rounds (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How many times the injector purge pulse is repeated, about 0.5 s apart. 0 and 1 both give a single round. Stock 0. No cylinder is enabled for injector purge in the stock calibration, so this has no effect on the stock calibration (dormant). Effect: leave at stock Evidence: ledger:E0436, ledger:E1774</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x26684" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rounds</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD7D" flags="0x0">
    <title>Torque Correction Loop - Drop Deadband</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The drop from the held peak of the torque correction loop is taken off the engine torque value only once twice the drop is larger than this value. Stock 5 Nm. Effect: leave at stock Evidence: ledger:E0612, ledger:E1796</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x214C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD7E" flags="0x0">
    <title>Secondary Air - Pressure Sensor Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pressure change over the full sensor voltage span (0 to 100 % of the reference voltage) when the secondary air pressure sensor reading is converted to kPa. Stock 109.6 kPa. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: must match the sensor Evidence: ledger:E0477, ledger:E1796</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa per 100 % of reference</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>254.996685</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*0.003891"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD7F" flags="0x0">
    <title>Secondary Air - Pressure Sensor Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pressure reported at 0 % of the reference voltage when the secondary air pressure sensor reading is converted to kPa. Stock 40 kPa. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: must match the sensor Evidence: ledger:E0477, ledger:E1796</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x328A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD80" flags="0x0">
    <title>Secondary Air - Distance Start Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The secondary air model keeps resetting its distance starting point until its timer passes this time; after that it counts distance from that point. Stock 5 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: leave at stock Evidence: ledger:E0624, ledger:E1796</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x326DA" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>-13421772.800000</min>
    <max>13421772.793750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD81" flags="0x0">
    <title>System Voltage OK Delay - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the PCM runs its system voltage OK delay check. 0: the check is skipped and its flag and counter are held clear. Stock 1. Effect: leave at stock Evidence: ledger:E0772, ledger:E1796</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x3679C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD82" flags="0x0">
    <title>Cam Phaser - Desired Angle Step Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Difference between the desired cam angle and its stored copy at or below which the cam phaser control takes its small-change path. Stock 14 deg. Effect: leave at stock Evidence: ledger:E0776, ledger:E1796</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x22C80" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD83" flags="0x0">
    <title>Service Throttle Test - Maximum Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this vehicle speed the scan tool throttle test is refused. Stock 4 km/h. Used only while the scan tool throttle test runs. Effect: safety interlock Evidence: ledger:E0775, ledger:E1796</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x24F14" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD84" flags="0x0">
    <title>Service Throttle Test - Maximum Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this engine speed the scan tool throttle test is refused. Stock 270 rpm. Used only while the scan tool throttle test runs. Effect: safety interlock Evidence: ledger:E0775, ledger:E1796</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x24F16" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD85" flags="0x0">
    <title>Service Throttle Test - Minimum MAP</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this manifold pressure the scan tool throttle test is refused. Stock 20 kPa. Used only while the scan tool throttle test runs. Effect: safety interlock Evidence: ledger:E0775, ledger:E1796</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x24F18" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD86" flags="0x0">
    <title>Service Throttle Test - Maximum Vacuum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this manifold vacuum (barometric pressure minus MAP) the scan tool throttle test is refused. Stock 80 kPa. Used only while the scan tool throttle test runs. Effect: safety interlock Evidence: ledger:E0775, ledger:E1796</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x24F1A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD87" flags="0x0">
    <title>Cam Control - Minimum System Voltage (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest system voltage at which this cam control enable path allows cam control. Stock 11.0 V. The path&#x27;s own enable switch is off in the stock calibration, so this has no effect on the stock calibration (dormant). Effect: leave at stock Evidence: ledger:E0769, ledger:E1796</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x33CFE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xD88" flags="0x30">
    <title>Coolant Warm-Up Monitor - Trouble Code by Step (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The trouble code each step of the coolant warm-up monitor reports, as an entry of the PCM&#x27;s code table. Stock P0125, P0128, P0128. Do not edit: another entry reports a different, unrelated code. Effect: do not edit Evidence: ledger:E0776, ledger:E1563, ledger:E1796</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>warm-up step</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="step 1" />
      <LABEL index="1" value="step 2" />
      <LABEL index="2" value="step 3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x337AA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>trouble code number</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xD89" flags="0x0">
    <title>Misfire - Cylinder Index Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The per-cylinder misfire counter that is credited is moved back by this many positions, wrapping at the cylinder count. Stock 0 (no shift). Effect: leave at stock Evidence: ledger:E0780, ledger:E1796</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36892" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cylinder positions</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD8A" flags="0x0">
    <title>ETC Monitor - Expected Throttle Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Under the throttle monitor&#x27;s stated conditions the expected throttle value is raised to at least this value. Stock 27.5 %. Effect: leave at stock Evidence: ledger:E0775, ledger:E1796</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x24F4A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD8B" flags="0x0">
    <title>Purge O2 Feedback - Forced Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Value the purge O2 feedback factor is set to in its reset state. Stock 1.00 (no correction). Effect: leave at stock Evidence: ledger:E0775, ledger:E1796</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25132" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD8C" flags="0x0">
    <title>Knock Learn Rate - Under-Sampled Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A cylinder whose knock learn sample count is below this value uses the blended learning rate. Same scale as the axis of the Knock Learn Rate - Sample Count Curve. Stock 2560. Effect: leave at stock Evidence: ledger:E0772, ledger:E1796</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2AEA0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples (raw)</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD8D" flags="0x0">
    <title>Fuel Trim Monitor - Confirm Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In its confirm state, with the fuel trim neither lean nor rich, the fuel trim monitor waits this long before it sets its result. Stock 3.0 s. Effect: diagnostic timing Evidence: ledger:E0462, ledger:E1796</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36260" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD8E" flags="0x0">
    <title>Throttle Position Sensor 1 - Voltage High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A throttle position sensor 1 reading above this voltage is treated as a circuit fault and sets the sensor 1 high input code (P0123). Stock 4.72 V. Effect: diagnostic limit Evidence: ledger:E0434, ledger:E1819</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x23C4E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>5.019531</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13056"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD8F" flags="0x0">
    <title>Throttle Position Sensor 1 - Voltage Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A throttle position sensor 1 reading below this voltage is treated as a circuit fault and sets the sensor 1 low input code (P0122). Stock 0.28 V. Effect: diagnostic limit Evidence: ledger:E0434, ledger:E1819</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x23C50" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>5.019531</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13056"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD90" flags="0x0">
    <title>Throttle Position Sensor 2 - Voltage High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A throttle position sensor 2 reading above this voltage is treated as a circuit fault and sets the sensor 2 high input code (P0223). Stock 4.72 V. Effect: diagnostic limit Evidence: ledger:E0434, ledger:E1819</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x23C52" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>5.019531</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13056"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD91" flags="0x0">
    <title>Throttle Position Sensor 2 - Voltage Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A throttle position sensor 2 reading below this voltage is treated as a circuit fault and sets the sensor 2 low input code (P0222). Stock 0.28 V. Effect: diagnostic limit Evidence: ledger:E0434, ledger:E1819</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x23C54" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>5.019531</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13056"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD92" flags="0x0">
    <title>P2610 Engine-Off Timer Check - Expected Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of engine-off timer counts expected between two samples of the engine-off timer check. A sample with a different step counts as bad, and enough bad samples set P2610. Stock 1. Effect: leave at stock Evidence: ledger:E0434, ledger:E1819</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37518" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>timer counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD93" flags="0x0">
    <title>Oil Pressure Monitor - Engine Running Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed the engine must stay above (for the running time) before the low oil pressure monitor treats it as running and can set its warning. Stock 550 rpm. Effect: leave at stock Evidence: ledger:E0776, ledger:E1819</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x23188" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD94" flags="0x0">
    <title>Oil Pressure Monitor - Engine Running Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the engine speed must stay above the running speed before the low oil pressure monitor treats the engine as running. Stock 2.5 s. Effect: leave at stock Evidence: ledger:E0776, ledger:E1819</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2318A" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD95" flags="0x0">
    <title>Traction Control Input - Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the last received traction control input values are kept without a new message before they are cleared. Stock 0 (cleared on the first tick after each message). Effect: leave at stock Evidence: ledger:E0434, ledger:E1819</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30374" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD96" flags="0x0">
    <title>P0128 Check - Minimum Intake Air Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The thermostat check P0128 only runs on a trip when the lowest intake air temperature since start is above this. Stock -6.75 degC. Effect: diagnostic enable window Evidence: ledger:E0587, ledger:E0920, ledger:E1819</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33730" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD97" flags="0x0">
    <title>Low Oil Pressure Check - Set Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long low oil pressure must be seen, with the engine running, before the PCM sets its low oil pressure state: the low oil pressure input active (stock, oil pressure estimate path), or with the sensor path on, oil pressure below the minimum oil pressure for the engine speed. Stock 1.0 s. Effect: longer delays the warning Evidence: ledger:E0776, ledger:E1829, ledger:E1831</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23186" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD98" flags="0x0">
    <title>Oil Pressure Sensor Path Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the PCM reads engine oil pressure from the oil pressure sensor (Engine Oil Pressure vs Sensor Voltage) and runs the low oil pressure check against the minimum oil pressure for the engine speed. 0: the sensor is not used. Stock 0 (the H3 calibration uses the oil pressure estimate). Effect: 1 only with an oil pressure sensor fitted Evidence: ledger:E0436, ledger:E1831</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x2318C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD99" flags="0x0">
    <title>Oil Pressure Estimate Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the PCM estimates engine oil pressure from coolant temperature and engine speed (Engine Oil Pressure Estimate tables), sends it on the vehicle bus, and sets its low oil pressure state from the low oil pressure input. 0: no estimate. Stock 1. Effect: leave at stock Evidence: ledger:E0436, ledger:E1831</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x2318E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD9A" flags="0x0">
    <title>Throttle Position - Minimum Learn Change Band</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How far the throttle position reading may move from its lowest value so far before the closed-throttle position learn restarts its settle time and follows the new reading. Also the least change from the stored learned value needed to replace it. Stock 0.50 %. Effect: leave at stock Evidence: ledger:E0436, ledger:E1838</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31374" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD9B" flags="0x0">
    <title>Throttle Position - Minimum Learn Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the throttle position reading must stay within the learn change band before the closed-throttle position learn stores it as the learned minimum. Stock 0.06 s. Effect: leave at stock Evidence: ledger:E0436, ledger:E1838</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31378" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD9C" flags="0x0">
    <title>Throttle Position Sensor 1 - Backup Full Scale Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On the backup throttle position path, the throttle position sensor 1 voltage that reads as 100 % (the learned closed-throttle voltage reads as 0 %). Stock 4.42 V. Effect: leave at stock Evidence: ledger:E0764, ledger:E1839</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31390" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>5.019531</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13056"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD9D" flags="0x0">
    <title>Secondary Air - Pressure Sensor Circuit High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A secondary air pressure sensor reading above this share of the reference voltage is a circuit high fault (P2433 bank 1, P2438 bank 2). Stock 95.4 %. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: diagnostic limit Evidence: ledger:E0676, ledger:E1839</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32898" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% of reference</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD9E" flags="0x0">
    <title>Secondary Air - Pressure Sensor Circuit Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A secondary air pressure sensor reading below this share of the reference voltage is a circuit low fault (P2432 bank 1, P2437 bank 2). Stock 5.0 %. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: diagnostic limit Evidence: ledger:E0527, ledger:E0676, ledger:E1839</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3289A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% of reference</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD9F" flags="0x0">
    <title>Pedal Position Sensors - Learned Minimum Mismatch Limit (P2138)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest allowed difference between the learned closed-pedal values of the two pedal position sensors; a larger difference counts as a failed P2138 sample. Stock 5.0 %. Effect: diagnostic limit Evidence: ledger:E0434, ledger:E1251, ledger:E1839</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x23B82" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDA0" flags="0x0">
    <title>Idle Speed Control - Spark Term Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower limit on the idle spark term the idle speed controller works with; a lower idle spark term is raised to this value. The idle spark term is the idle base spark plus the idle underspeed spark correction; the idle speed controller uses the limited term when it sets the idle airflow request. Stock -16.0 deg. Effect: leave at stock Evidence: ledger:E0632, ledger:E1852</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22356" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDA1" flags="0x0">
    <title>Idle Speed Control - Spark Term Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit on the idle spark term the idle speed controller works with; a higher idle spark term is lowered to this value. The idle spark term is the idle base spark plus the idle underspeed spark correction; the idle speed controller uses the limited term when it sets the idle airflow request. Stock 25.0 deg. Effect: leave at stock Evidence: ledger:E0632, ledger:E1852</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22358" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDA2" flags="0x0">
    <title>Reduced Engine Power - Speed Filter Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the filtered vehicle speed used by the reduced engine power throttle limit follows the measured speed, as the fraction of the gap closed per update. Part of the reduced engine power throttle limit, which is active only while a throttle control fault is set; it limits the throttle when the vehicle accelerates harder than allowed (a sign of wheel spin or a false speed reading). Stock 0.22. Effect: leave at stock Evidence: ledger:E1867</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x23DD2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDA3" flags="0x0">
    <title>Reduced Engine Power - Throttle Area Limit at Low Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While a throttle control fault is active, at 8 km/h or slower the throttle opening is limited to this share of full throttle area. Stock 6.3 %. Effect: raise = more throttle allowed at low speed under reduced engine power Evidence: ledger:E1867</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x23DD4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDA4" flags="0x0">
    <title>Reduced Engine Power - High Speed Band Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this vehicle speed the high speed acceleration threshold applies. Part of the reduced engine power throttle limit, which is active only while a throttle control fault is set; it limits the throttle when the vehicle accelerates harder than allowed (a sign of wheel spin or a false speed reading). Stock 36.0 km/h. Effect: leave at stock Evidence: ledger:E1867</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x23DD6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDA5" flags="0x0">
    <title>Reduced Engine Power - Low Speed Band End</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this vehicle speed the low speed acceleration threshold applies; between this and the high speed band start the middle threshold applies. Part of the reduced engine power throttle limit, which is active only while a throttle control fault is set; it limits the throttle when the vehicle accelerates harder than allowed (a sign of wheel spin or a false speed reading). Stock 16.0 km/h. Effect: leave at stock Evidence: ledger:E1867</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x23DD8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDA6" flags="0x0">
    <title>Reduced Engine Power - Acceleration Threshold, High Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle acceleration above which the reduced engine power throttle limit starts, used above the high speed band start. Part of the reduced engine power throttle limit, which is active only while a throttle control fault is set; it limits the throttle when the vehicle accelerates harder than allowed (a sign of wheel spin or a false speed reading). Stock 38.4 km/h/s. Effect: raise = harder acceleration allowed before the limit starts Evidence: ledger:E1867</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x23DDA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDA7" flags="0x0">
    <title>Reduced Engine Power - Acceleration Threshold, Middle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle acceleration above which the reduced engine power throttle limit starts, used between the two speed bands. Part of the reduced engine power throttle limit, which is active only while a throttle control fault is set; it limits the throttle when the vehicle accelerates harder than allowed (a sign of wheel spin or a false speed reading). Stock 38.4 km/h/s. Effect: raise = harder acceleration allowed before the limit starts Evidence: ledger:E1867</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x23DDC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDA8" flags="0x0">
    <title>Reduced Engine Power - Acceleration Threshold, Low Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle acceleration above which the reduced engine power throttle limit starts, used below the low speed band end. Part of the reduced engine power throttle limit, which is active only while a throttle control fault is set; it limits the throttle when the vehicle accelerates harder than allowed (a sign of wheel spin or a false speed reading). Stock 38.4 km/h/s. Effect: raise = harder acceleration allowed before the limit starts Evidence: ledger:E1867</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x23DDE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDA9" flags="0x0">
    <title>Segment 2 (System) - GM Part Number</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. GM service part number of this calibration segment. The same number is stored as text a few bytes later. It identifies which calibration version is in the PCM; it does not change how the engine runs. Read only. Effect: identification only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x20004" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>part number</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>4294967295.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDAA" flags="0x0">
    <title>Segment 2 (System) - Checksum (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Checksum word of this segment: every 16-bit word of the segment, this one included, adds up to zero. Your flash or checksum tool must recompute it after any edit in this segment. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x20000" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDAB" flags="0x0">
    <title>Segment 2 (System) - ROM Check CRC (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Check value the PCM&#x27;s ROM test (P0601) compares against while the engine runs: a CRC-16 of the segment, stored with its bytes swapped. If it is not updated after an edit in this segment, the PCM can set P0601. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x2001C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDAC" flags="0x0">
    <title>Segment 3 (Fuel / System) - GM Part Number</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. GM service part number of this calibration segment. The same number is stored as text a few bytes later. It identifies which calibration version is in the PCM; it does not change how the engine runs. Read only. Effect: identification only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x20104" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>part number</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>4294967295.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDAD" flags="0x0">
    <title>Segment 3 (Fuel / System) - Checksum (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Checksum word of this segment: every 16-bit word of the segment, this one included, adds up to zero. Your flash or checksum tool must recompute it after any edit in this segment. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x20100" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDAE" flags="0x0">
    <title>Segment 3 (Fuel / System) - ROM Check CRC (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Check value the PCM&#x27;s ROM test (P0601) compares against while the engine runs: a CRC-16 of the segment, stored with its bytes swapped. If it is not updated after an edit in this segment, the PCM can set P0601. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x2011C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDAF" flags="0x0">
    <title>Segment 4 (Engine Calibration) - GM Part Number</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. GM service part number of this calibration segment. The same number is stored as text a few bytes later. It identifies which calibration version is in the PCM; it does not change how the engine runs. Read only. Effect: identification only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x20A24" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>part number</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>4294967295.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDB0" flags="0x0">
    <title>Segment 4 (Engine Calibration) - Checksum (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Checksum word of this segment: every 16-bit word of the segment, this one included, adds up to zero. Your flash or checksum tool must recompute it after any edit in this segment. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x20A20" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDB1" flags="0x0">
    <title>Segment 4 (Engine Calibration) - ROM Check CRC (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Check value the PCM&#x27;s ROM test (P0601) compares against while the engine runs: a CRC-16 of the segment, stored with its bytes swapped. If it is not updated after an edit in this segment, the PCM can set P0601. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x20A3C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDB2" flags="0x0">
    <title>Segment 5 (Engine Diagnostics) - GM Part Number</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. GM service part number of this calibration segment. The same number is stored as text a few bytes later. It identifies which calibration version is in the PCM; it does not change how the engine runs. Read only. Effect: identification only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x32664" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>part number</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>4294967295.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDB3" flags="0x0">
    <title>Segment 5 (Engine Diagnostics) - Checksum (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Checksum word of this segment: every 16-bit word of the segment, this one included, adds up to zero. Your flash or checksum tool must recompute it after any edit in this segment. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x32660" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDB4" flags="0x0">
    <title>Segment 5 (Engine Diagnostics) - ROM Check CRC (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Check value the PCM&#x27;s ROM test (P0601) compares against while the engine runs: a CRC-16 of the segment, stored with its bytes swapped. If it is not updated after an edit in this segment, the PCM can set P0601. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x3267C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDB5" flags="0x0">
    <title>Segment 6 (Transmission Calibration) - GM Part Number</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. GM service part number of this calibration segment. The same number is stored as text a few bytes later. It identifies which calibration version is in the PCM; it does not change how the engine runs. Read only. Effect: identification only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x37594" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>part number</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>4294967295.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDB6" flags="0x0">
    <title>Segment 6 (Transmission Calibration) - Checksum (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Checksum word of this segment: every 16-bit word of the segment, this one included, adds up to zero. Your flash or checksum tool must recompute it after any edit in this segment. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x37590" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDB7" flags="0x0">
    <title>Segment 6 (Transmission Calibration) - ROM Check CRC (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Check value the PCM&#x27;s ROM test (P0601) compares against while the engine runs: a CRC-16 of the segment, stored with its bytes swapped. If it is not updated after an edit in this segment, the PCM can set P0601. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x375AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDB8" flags="0x0">
    <title>Segment 7 (Transmission Diagnostics) - GM Part Number</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. GM service part number of this calibration segment. The same number is stored as text a few bytes later. It identifies which calibration version is in the PCM; it does not change how the engine runs. Read only. Effect: identification only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x3F4C4" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>part number</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>4294967295.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDB9" flags="0x0">
    <title>Segment 7 (Transmission Diagnostics) - Checksum (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Checksum word of this segment: every 16-bit word of the segment, this one included, adds up to zero. Your flash or checksum tool must recompute it after any edit in this segment. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x3F4C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDBA" flags="0x0">
    <title>Segment 7 (Transmission Diagnostics) - ROM Check CRC (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Check value the PCM&#x27;s ROM test (P0601) compares against while the engine runs: a CRC-16 of the segment, stored with its bytes swapped. If it is not updated after an edit in this segment, the PCM can set P0601. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x3F4DC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xDBB" flags="0x30">
    <title>P0507 Idle Speed High - Speed Error Threshold vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed above desired by at least this much (by coolant temperature) runs the P0507 fail timer; once it reaches the high-error fail time one P0507 fail period is counted. Stock 150 rpm at all temperatures. Part of the idle speed diagnostic (P0506 idle speed lower than expected, P0507 higher than expected), which runs only once its enable conditions are met. Effect: raise = more overspeed needed before P0507 counts Evidence: ledger:E0639, ledger:E1239, ledger:E1606</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36560" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>-4096.000000</min>
      <max>4095.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDBC" flags="0x30">
    <title>P0506 Idle Speed Low - Speed Error Threshold vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed below desired by at least this much (negative values, by coolant temperature) runs the P0506 fail timer; once it reaches the low-error fail time one P0506 fail period is counted. Stock -75 rpm at all temperatures. Part of the idle speed diagnostic (P0506 idle speed lower than expected, P0507 higher than expected), which runs only once its enable conditions are met. Effect: lower (more negative) = more underspeed needed before P0506 counts Evidence: ledger:E0639, ledger:E1239, ledger:E1606</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36584" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>-4096.000000</min>
      <max>4095.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xDBD" flags="0x0">
    <title>Acceleration Torque Limit - Engine Torque Request (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Engine torque the transmission requests from the engine controller while the limit is active (basic modes). Stock 25 Nm. Part of the acceleration torque limit, which is switched off on this truck (master switch off), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1493, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3FED4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDBE" flags="0x0">
    <title>Vehicle Bus - Generator Field Duty Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Change in the generator field duty that triggers a new send of its message. Stock 1.0 %. Vehicle bus (serial data to the other modules): the message is sent again once at least the minimum interval has passed since it was last sent and the value has changed by at least the change threshold (or a status in it changed). Effect: lower = the duty is reported in finer steps Evidence: ledger:E0776, ledger:E0805, ledger:E1606, ledger:E1676</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20290" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDBF" flags="0x0">
    <title>Cam Command Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The filter gain used when blending the commanded cam angle input into the value the engine actually uses. Stock is effectively 1.0, about 99.998 percent, meaning the commanded value currently passes through with essentially no filtering. Effect: Lowering it adds smoothing and lag to the cam command relative to its input; raising it toward the maximum keeps it close to unfiltered, which is the stock setting. Evidence: ledger:E0776, ledger:E0805, ledger:E1606</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x33CFA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain (fraction x65536)</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDC0" flags="0x0">
    <title>Secondary Air - Fallback Run Time, Cold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Secondary air run time used below the fallback coolant limit when the catalyst temperature curves are not used. Stock 0 s. Secondary air injection is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0573, ledger:E0836, ledger:E1193, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA2E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDC1" flags="0x0">
    <title>Secondary Air - Fallback Fuel Correction Time, Cold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Secondary air fuel correction time used below the fallback coolant limit when the catalyst temperature curves are not used. Stock 20 s. Secondary air injection is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0573, ledger:E0836, ledger:E1193, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA32" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xDC2" flags="0x30">
    <title>Cold Start Emission Monitor - Spark Term vs Spark Advance (dormant, DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark term curve of the cold start emission monitor (fault code P1400): converts spark advance (minus 30 to 50 degrees) into the monitor&#x27;s spark term. The same curve is applied to the expected and to the actual spark advance, and each spark term is multiplied by the matching speed term before the monitor compares expected with actual. On this calibration the monitor is switched off and the curve&#x27;s size word is blank, so it is never used; the points are shown at the size the lookup has when the monitor is in use. Dormant: no effect on this truck&#x27;s software. Shown as the raw stored value. Reference only: DO NOT E...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>deg</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-30" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="-10" />
      <LABEL index="3" value="0" />
      <LABEL index="4" value="10" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="40" />
      <LABEL index="8" value="50" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33274" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDC3" flags="0x30">
    <title>Cold Start Emission Monitor - Speed Term vs RPM (dormant, DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Speed term curve of the cold start emission monitor (fault code P1400): converts engine speed (0 to 2400 rpm) into the monitor&#x27;s speed term. The same curve is applied to the expected and to the actual engine speed, and each speed term is multiplied by the matching spark term before the monitor compares expected with actual. On this calibration the monitor is switched off and the curve&#x27;s size word is blank, so it is never used; the points are shown at the size the lookup has when the monitor is in use. Dormant: no effect on this truck&#x27;s software. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="300" />
      <LABEL index="2" value="600" />
      <LABEL index="3" value="900" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1500" />
      <LABEL index="6" value="1800" />
      <LABEL index="7" value="2100" />
      <LABEL index="8" value="2400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3325E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xDC4" flags="0x0">
    <title>Trans Slip (P0894) Count Check - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 10 %. P0894 (transmission component slipping) count check: while the converter clutch is applied and the throttle request is inside its window, converter slip that stays inside the count check slip window for the count check time adds one count; at the count check counts the PCM reports P0894. Effect: raise = the count check needs a larger throttle request Evidence: ledger:E0789, ledger:E0849, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F71C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDC5" flags="0x0">
    <title>Converter Model - Capacity Torque Adder, Torque High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. Engine torque at or above which the low torque capacity factor adder is 0. Stock 203 Nm. The stock end value is 0, so this adder has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1419, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDC6" flags="0x0">
    <title>Converter Model - Capacity Torque Adder, Torque Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. Engine torque at or below which the low torque capacity factor adder is at its full value. Stock 90 Nm. The stock end value is 0, so this adder has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1419, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E9D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xDC7" flags="0x30">
    <title>Coolant Temp Sensor - Resistance Points</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor resistance at each of the 33 temperature points of the coolant temperature sensor (stock 47 ohm at 150 C to 100.7 kohm at -40 C, the standard GM thermistor). Paired with Coolant Temp Sensor - Temperature Points. Change only for a different sensor. Effect: reported and used coolant temperature Evidence: ledger:E0392, ledger:E1047, ledger:E1606</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22844" mmedelementsizebits="32" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ohm</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>134217727.968750</max>
      <MATH equation="X/32"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xDC8" flags="0x0">
    <title>Secondary Air - Fallback Cold Coolant Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the catalyst temperature curves are not used, coolant below this selects the cold run time and fuel correction time, otherwise the warm ones. Stock 60 C. Secondary air injection is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0573, ledger:E0836, ledger:E1193, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA2C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xDC9" flags="0x30">
    <title>Crank Output Mode 2 - Lower Engine Speed vs Battery Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. Engine speed at or below which the crank-timed output channels enter mode 2, by battery voltage (with the upper speed above it ending the mode). Used only when mode 2 is enabled. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = mode 2 starts at a higher engine speed at that voltage) Evidence: ledger:E0644, ledger:E0749, ledge...</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>22</indexcount>
      <units>V (battery)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="4.5" />
      <LABEL index="1" value="5.5" />
      <LABEL index="2" value="6.5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="8.5" />
      <LABEL index="5" value="9.5" />
      <LABEL index="6" value="10.5" />
      <LABEL index="7" value="11.5" />
      <LABEL index="8" value="12.5" />
      <LABEL index="9" value="13.5" />
      <LABEL index="10" value="14.5" />
      <LABEL index="11" value="15.5" />
      <LABEL index="12" value="16.5" />
      <LABEL index="13" value="17.5" />
      <LABEL index="14" value="18.5" />
      <LABEL index="15" value="19.5" />
      <LABEL index="16" value="20.5" />
      <LABEL index="17" value="21.5" />
      <LABEL index="18" value="22.5" />
      <LABEL index="19" value="23.5" />
      <LABEL index="20" value="24.5" />
      <LABEL index="21" value="25.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CE54" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="22" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDCA" flags="0x30">
    <title>Crank Output Mode 2 - Upper Engine Speed vs Battery Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. Upper engine speed of the mode 2 band of the crank-timed output channels, by battery voltage: once in mode 2, the outputs stay in it until engine speed reaches this. Used only when mode 2 is enabled. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = mode 2 is kept up to a higher engine speed at that voltage) Evidence: ledger:E...</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>22</indexcount>
      <units>V (battery)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="4.5" />
      <LABEL index="1" value="5.5" />
      <LABEL index="2" value="6.5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="8.5" />
      <LABEL index="5" value="9.5" />
      <LABEL index="6" value="10.5" />
      <LABEL index="7" value="11.5" />
      <LABEL index="8" value="12.5" />
      <LABEL index="9" value="13.5" />
      <LABEL index="10" value="14.5" />
      <LABEL index="11" value="15.5" />
      <LABEL index="12" value="16.5" />
      <LABEL index="13" value="17.5" />
      <LABEL index="14" value="18.5" />
      <LABEL index="15" value="19.5" />
      <LABEL index="16" value="20.5" />
      <LABEL index="17" value="21.5" />
      <LABEL index="18" value="22.5" />
      <LABEL index="19" value="23.5" />
      <LABEL index="20" value="24.5" />
      <LABEL index="21" value="25.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CE26" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="22" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xDCB" flags="0x0">
    <title>Cruise Control - Cancel Above Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: an active cruise is cancelled when vehicle speed rises above this. Stock 230 km/h (143 mph). Effect: lower = cruise cancels at a lower speed Evidence: ledger:E1044, ledger:E1606</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21EAE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDCC" flags="0x0">
    <title>Cruise Control - Cancel Below Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: an active cruise is cancelled when vehicle speed falls below this. Stock 38 km/h (23.6 mph). Effect: lower = cruise stays engaged down to a lower speed Evidence: ledger:E1044, ledger:E1606</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x21EAC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xDCD" flags="0x30">
    <title>Desired Shift Time Altitude Adder - 4WD Low (1-2 / 2-3 / 3-4)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time added to the desired upshift duration at altitude, by shift torque, set 2 (4WD Low on the stock calibration); scaled by the Desired Shift Time Altitude Weight table (1.0 at low barometric pressure, 0 at sea level on the stock calibration). Negative values shorten the target. Stock 0 in every cell. Which set each drive mode uses is chosen by Shift Set by Drive Mode. Effect: longer (positive) or shorter (negative) upshift target at altitude Evidence: ledger:E0235, ledger:E0237, ledger:E1311, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3E3FA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT; data columns: shift torque (Nm))</units>
      <embedinfo type="1" />
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C168" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>-3.200000</min>
      <max>3.175000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDCE" flags="0x30">
    <title>Desired Shift Time vs Torque - 4WD Low (1-2 / 2-3 / 3-4)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target upshift duration the adaptive shift learning steers to, by shift torque, set 2 (4WD Low on the stock calibration); 0 = not adapted. Stock 0 in every cell (4WD Low upshifts are not adapted). Which set each drive mode uses is chosen by Shift Set by Drive Mode. Effect: 4WD Low adaptive shift duration target (0 = not adapted) Evidence: ledger:E0235, ledger:E0237, ledger:E1311, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3E3FA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT; data columns: shift torque (Nm))</units>
      <embedinfo type="1" />
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C0B8" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDCF" flags="0x30">
    <title>Cold Start Emission Monitor - Expected Idle Speed, In Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Expected engine speed for the cold start emission monitor (fault code P1400: the check that the engine really runs the fast idle and spark timing used to warm the catalytic converter after a cold start), by time since start (rows, 0 to 42.5 s) and coolant temperature (columns), with the transmission in gear. The monitor compares this with the actual engine speed while the vehicle is stopped with the throttle closed. On this calibration the monitor is switched off and the table&#x27;s size words are blank, so the cells are never used; rows and columns are shown in the layout the lookup uses when it is sized on other calib...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="2.656" />
      <LABEL index="2" value="5.312" />
      <LABEL index="3" value="7.969" />
      <LABEL index="4" value="10.625" />
      <LABEL index="5" value="13.281" />
      <LABEL index="6" value="15.938" />
      <LABEL index="7" value="18.594" />
      <LABEL index="8" value="21.25" />
      <LABEL index="9" value="23.906" />
      <LABEL index="10" value="26.562" />
      <LABEL index="11" value="29.219" />
      <LABEL index="12" value="31.875" />
      <LABEL index="13" value="34.531" />
      <LABEL index="14" value="37.188" />
      <LABEL index="15" value="39.844" />
      <LABEL index="16" value="42.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x32C60" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDD0" flags="0x30">
    <title>Cold Start Emission Monitor - Expected Idle Speed, Park / Neutral (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Expected engine speed for the cold start emission monitor (fault code P1400: the check that the engine really runs the fast idle and spark timing used to warm the catalytic converter after a cold start), by time since start (rows, 0 to 42.5 s) and coolant temperature (columns), with the transmission in Park or Neutral. The monitor compares this with the actual engine speed while the vehicle is stopped with the throttle closed. On this calibration the monitor is switched off and the table&#x27;s size words are blank, so the cells are never used; rows and columns are shown in the layout the lookup uses when it is sized on...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="2.656" />
      <LABEL index="2" value="5.312" />
      <LABEL index="3" value="7.969" />
      <LABEL index="4" value="10.625" />
      <LABEL index="5" value="13.281" />
      <LABEL index="6" value="15.938" />
      <LABEL index="7" value="18.594" />
      <LABEL index="8" value="21.25" />
      <LABEL index="9" value="23.906" />
      <LABEL index="10" value="26.562" />
      <LABEL index="11" value="29.219" />
      <LABEL index="12" value="31.875" />
      <LABEL index="13" value="34.531" />
      <LABEL index="14" value="37.188" />
      <LABEL index="15" value="39.844" />
      <LABEL index="16" value="42.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x32D98" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDD1" flags="0x30">
    <title>Cold Start Emission Monitor - Expected Spark vs Airmass x RPM (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Expected spark advance for the cold start emission monitor (fault code P1400), by cylinder airmass (rows) and engine speed (columns), used in every spark mode except the one that has its own pair of expected spark tables. The value is multiplied by four factor curves (run time, start-up coolant, coolant and throttle) and the monitor compares the result with the actual spark advance. On this calibration the monitor is switched off and the table&#x27;s size words are blank, so the cells are never used. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0401, ledger:E0718, ledger:...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1000" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1400" />
      <LABEL index="6" value="1600" />
      <LABEL index="7" value="1800" />
      <LABEL index="8" value="2000" />
      <LABEL index="9" value="2200" />
      <LABEL index="10" value="2400" />
      <LABEL index="11" value="2600" />
      <LABEL index="12" value="2800" />
      <LABEL index="13" value="3000" />
      <LABEL index="14" value="3200" />
      <LABEL index="15" value="3400" />
      <LABEL index="16" value="3600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.16" />
      <LABEL index="2" value="0.24" />
      <LABEL index="3" value="0.32" />
      <LABEL index="4" value="0.4" />
      <LABEL index="5" value="0.48" />
      <LABEL index="6" value="0.56" />
      <LABEL index="7" value="0.64" />
      <LABEL index="8" value="0.72" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x330C0" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDD2" flags="0x30">
    <title>2-1 Downshift Pressure - Input Torque Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission input torque points (rows) of the 2-1 downshift pressure tables. Stock 0 to 200 Nm in 12.5 Nm steps. The tables that use it are spread over these points, so moving them re-spaces those tables; keep the point count and keep the points rising. Effect: moves the torque axis of every table that uses it: edit with care Evidence: ledger:E0693, ledger:E0834, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37C6E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>-4096.000000</min>
      <max>4095.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDD3" flags="0x30">
    <title>2-1 Downshift Pressure - Baro Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Breakpoints of the 2-1 downshift pressure model: barometric pressure, 65 to 105 kPa (baro multipliers). Axis data: keep ascending. Effect: moves the 2-1 downshift pressure table points Evidence: ledger:E1155, ledger:E1286, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37CDA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDD4" flags="0x30">
    <title>2-1 Downshift Pressure Baro Multiplier (above 38.5 mph)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the high-speed 2-1 downshift pressure by barometric pressure. Stock 0.25 at 65 kPa rising to 1.00 at 100 kPa and above. Active only during a 2-1 downshift (from 2nd with a downshift commanded, until it leaves 2nd); replaces the normal shift pressure (E0334). Effect: 2-1 downshift pressure at altitude Evidence: ledger:E0334, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x37CDA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>kPa (barometric)</units>
      <embedinfo type="1" />
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37ADA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDD5" flags="0x30">
    <title>2-1 Downshift Pressure Baro Multiplier (at or below 38.5 mph)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the low-speed 2-1 downshift pressure by barometric pressure. Stock 0.50 at 65 kPa rising to 1.00 at 95 kPa and above. Active only during a 2-1 downshift (from 2nd with a downshift commanded, until it leaves 2nd); replaces the normal shift pressure (E0334). Effect: 2-1 downshift pressure at altitude Evidence: ledger:E0334, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x37CDA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>kPa (barometric)</units>
      <embedinfo type="1" />
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37AB6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDD6" flags="0x30">
    <title>2-1 Downshift Pressure - Intake Air Temp Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Breakpoints of the 2-1 downshift pressure model: intake air temperature, -30 to 90 C (intake air multipliers). Axis data: keep ascending. Effect: moves the 2-1 downshift pressure table points Evidence: ledger:E1155, ledger:E1286, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37CFE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDD7" flags="0x30">
    <title>2-1 Downshift Pressure vs Torque vs Speed (above 38.5 mph)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift pressure used for a 2-1 downshift that starts above 38.5 mph (62 km/h), by input torque and the speed when the downshift began. Stock 3.5 to 64.4 psi. Active only during a 2-1 downshift (from 2nd with a downshift commanded, until it leaves 2nd); replaces the normal shift pressure. Effect: 2-1 downshift firmness (high speed) Evidence: ledger:E0334, ledger:E0694, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>mph (speed when the 2-1 downshift started)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="44.7" />
      <LABEL index="1" value="46.9" />
      <LABEL index="2" value="48.5" />
      <LABEL index="3" value="50.6" />
      <LABEL index="4" value="52.8" />
      <LABEL index="5" value="55.0" />
      <LABEL index="6" value="57.2" />
      <LABEL index="7" value="59.3" />
      <LABEL index="8" value="61.5" />
      <LABEL index="9" value="63.7" />
      <LABEL index="10" value="65.9" />
      <LABEL index="11" value="68.0" />
      <LABEL index="12" value="70.2" />
      <LABEL index="13" value="72.4" />
      <LABEL index="14" value="74.6" />
      <LABEL index="15" value="76.7" />
      <LABEL index="16" value="79.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x37C6E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>Nm (transmission input torque)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37823" mmedelementsizebits="8" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>psi</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>147.938505</max>
      <MATH equation="X*0.580151"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDD8" flags="0x30">
    <title>2-1 Downshift Pressure vs Torque vs Speed (at or below 38.5 mph)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift pressure used for a 2-1 downshift that starts at or below 38.5 mph (62 km/h), by input torque and the speed when the downshift began. Stock 0 to 69.6 psi. Times the baro multiplier, plus the trans-temp adder, capped at max line pressure. Active only during a 2-1 downshift (from 2nd with a downshift commanded, until it leaves 2nd); replaces the normal shift pressure. Effect: 2-1 downshift firmness (low speed) Evidence: ledger:E0334, ledger:E0694, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>mph (speed when the 2-1 downshift started)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="15.5" />
      <LABEL index="1" value="17.1" />
      <LABEL index="2" value="18.6" />
      <LABEL index="3" value="20.2" />
      <LABEL index="4" value="21.7" />
      <LABEL index="5" value="23.3" />
      <LABEL index="6" value="24.9" />
      <LABEL index="7" value="26.4" />
      <LABEL index="8" value="28.0" />
      <LABEL index="9" value="29.5" />
      <LABEL index="10" value="31.1" />
      <LABEL index="11" value="32.6" />
      <LABEL index="12" value="34.2" />
      <LABEL index="13" value="35.7" />
      <LABEL index="14" value="37.3" />
      <LABEL index="15" value="38.8" />
      <LABEL index="16" value="40.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x37C6E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>Nm (transmission input torque)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3794B" mmedelementsizebits="8" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>psi</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>147.938505</max>
      <MATH equation="X*0.580151"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDD9" flags="0x30">
    <title>2-1 Downshift Pressure - RPM Breakpoints (high speed adder)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Breakpoints of the 2-1 downshift pressure model: engine speed when the downshift started, 1000 to 2800 rpm (high speed rpm adder). Axis data: keep ascending. Effect: moves the 2-1 downshift pressure table points Evidence: ledger:E1155, ledger:E1286, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37C26" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDDA" flags="0x30">
    <title>2-1 Downshift Pressure - RPM Breakpoints (low speed adder)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Breakpoints of the 2-1 downshift pressure model: engine speed when the downshift started, 500 to 2300 rpm (low speed rpm adder). Axis data: keep ascending. Effect: moves the 2-1 downshift pressure table points Evidence: ledger:E1155, ledger:E1286, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37C4A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDDB" flags="0x30">
    <title>2-1 Downshift Pressure - Speed Breakpoints (high speed tables)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Breakpoints of the 2-1 downshift pressure model: vehicle speed when the downshift started, 72 to 128 km/h (high speed tables). Axis data: keep ascending. Effect: moves the 2-1 downshift pressure table points Evidence: ledger:E1155, ledger:E1286, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37C92" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDDC" flags="0x30">
    <title>2-1 Downshift Pressure - Speed Breakpoints (low speed tables)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Breakpoints of the 2-1 downshift pressure model: vehicle speed when the downshift started, 25 to 65 km/h (low speed tables). Axis data: keep ascending. Effect: moves the 2-1 downshift pressure table points Evidence: ledger:E1155, ledger:E1286, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37CB6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xDDD" flags="0x0">
    <title>2-1 Downshift Pressure - Table Split Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or below this speed (when the 2-1 downshift starts) the low-speed pressure table and baro multiplier are used, above it the high-speed ones. Stock 38.5 mph (62 km/h). Active only during a 2-1 downshift (from 2nd with a downshift commanded, until it leaves 2nd); replaces the normal shift pressure (E0334). Effect: which 2-1 downshift pressure table applies Evidence: ledger:E0334, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x375C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>mph</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>318.137196</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/205.996032"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDDE" flags="0x0">
    <title>Engine Speed Filter Weight - Filtered Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new engine speed reading taken into the filtered engine speed every 25 ms. The filtered engine speed is the one the transmission logic reads (garage shift, shift and converter clutch checks). Stock 0.75. Effect: lower = smoother but slower filtered engine speed; 1.0 = no filtering Evidence: ledger:E1570, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x37D68" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDDF" flags="0x0">
    <title>Secondary Air Run - Barometric Pressure Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. Secondary air: the run time is only set up when barometric pressure is at or above this (not at high altitude). Stock 60 kPa. Secondary air injection is switched off on the stock H3 and the stock start-up coolant bounds cannot both be met, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = secondary air is skipped at lower a...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA14" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDE0" flags="0x0">
    <title>Secondary Air Run - Intake Air Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. Secondary air: the run time is only set up when the intake air temperature is at or above this. Stock 140 C. Secondary air injection is switched off on the stock H3 and the stock start-up coolant bounds cannot both be met, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = secondary air needs warmer intake air) Evidence: led...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA0C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDE1" flags="0x0">
    <title>Secondary Air Run - Distance Since New Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. Secondary air: the run time is only set up once the vehicle has covered at least this distance since new. Stock 15 km. Secondary air injection is switched off on the stock H3 and the stock start-up coolant bounds cannot both be met, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = secondary air waits for more distance on a...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA10" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1048575.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xDE2" flags="0x30">
    <title>Garage Shift - A/B Table Select, Converter Slip Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Garage shift (shift from Park or Neutral into gear): converter slip (engine minus turbine speed) below this uses the (A) garage tables, at or above it the (B) tables, into Drive and into Reverse. By fluid temperature (-40 to 152 C). Stock 600 rpm at every temperature. Effect: raise = more converter slip needed before the (B) garage tables are used Evidence: ledger:E1236, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x381C6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDE3" flags="0x30">
    <title>Intake Air Temp Sensor - Resistance Points</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor resistance at each of the 33 temperature points of the intake air temperature sensor (stock 64 ohm at 150 C to 51.5 kohm at -40 C). Paired with Intake Air Temp Sensor - Temperature Points. Change only for a different sensor. Effect: reported and used intake air temperature Evidence: ledger:E1047, ledger:E1606</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29018" mmedelementsizebits="32" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ohm</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>134217727.968750</max>
      <MATH equation="X/32"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDE4" flags="0x30">
    <title>Idle Airflow - Coolant Adder</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle base airflow added vs coolant temperature. Stock +2.39 g/s at -40 C falling to 0 at 68-104 C and -0.12 g/s at 152 C. Adds directly to the idle airflow request, so it sets how much extra air a cold engine gets at idle. Row 1 = In Gear, row 2 = Park/Neutral. Effect: raise = more idle air (higher idle rpm before closed-loop trims it) at that coolant temperature Evidence: ledger:E0286, ledger:E0287, ledger:E1606</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29E0E" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDE5" flags="0x30">
    <title>Idle Airflow - Alternator Load Adder vs RPM - In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added vs rpm (columns) and alternator field duty (rows, 0-100 %), In Gear. Stock 0 at the first row rising to 1.18 g/s at the last row from 512 rpm up. Effect: raise = more idle air when that load is present Evidence: ledger:E0286, ledger:E0287, ledger:E0294, ledger:E0936, ledger:E1606</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>% alternator field duty</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="25" />
      <LABEL index="2" value="50" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29C32" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDE6" flags="0x30">
    <title>Idle Airflow vs Desired RPM Above Base</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added for the part of the desired idle rpm above the base desired-idle-vs-coolant value (and above the start-up flare), e.g. A/C or other idle-up requests. Stock In Gear 0 to 3.85 g/s, Park/Neutral 0 to 2.28 g/s over 0-400 rpm. Row 1 = In Gear, row 2 = Park/Neutral. Effect: raise = more air per rpm of idle-up request (faster, fuller idle-up) Evidence: ledger:E0286, ledger:E0287, ledger:E1606</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29D36" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDE7" flags="0x30">
    <title>Idle Start-Up RPM Flare - Park/Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra desired idle rpm after a start (added to the desired idle vs coolant value, E0294) vs time since start (rows) and coolant (columns), Park/Neutral. Stock 200 rpm at start (450 rpm at 20 and 32 C) decaying to 0 by 64 s. The Idle Airflow vs Start-Up RPM Flare table supplies the air for it; after 8 s it is cancelled once the truck moves or the throttle opens. Effect: raise = higher, longer rpm flare after starting Evidence: ledger:E0286, ledger:E0287, ledger:E0294, ledger:E1606</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>s since start</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A32A" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDE8" flags="0x30">
    <title>Desired idle vs coolant temp - PARK/NEUTRAL</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target idle speed vs engine coolant temperature in park or neutral. Higher than the in-gear target at 20 and 32 C (850 vs 750 rpm); the two curves are identical above 44 C. Warm-up log matches the part of the curve shared with the other idle curve (186 samples at 47-88 C, mean error 4.7 rpm, E0115). Which curve is Park/Neutral and which is in-gear rests on code (E0123). Evidence: ledger:E0048, ledger:E0115, ledger:E0123, ledger:E0158, ledger:E0223, ledger:E0231, ledger:E1606</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A0A6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDE9" flags="0x30">
    <title>P0201 to P0205 Circuit Check - Fault Count and Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Injector circuit checks P0201 to P0205 (one count pair per cylinder): the code sets once the first value&#x27;s number of faulted samples is reached; if the second value&#x27;s number of samples is reached first, the check passes and both counts start again. Stock 10 and 20. Effect: raise the first value = more faulted samples are needed to set the code; raise the second = each window is longer Evidence: ledger:E1058, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>value</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="fault samples to fail" />
      <LABEL index="1" value="window samples to pass" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36794" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xDEA" flags="0x0">
    <title>Input Speed Sensor - Pulse Loss Updates to Zero (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. With the pulse loss handling switched on, each update without an input speed sensor pulse lowers the input speed reading to what one pulse over the elapsed time would mean, and after this many updates without a pulse the reading is 0. Stock 0. The pulse loss handling is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0783, ledger:E1514, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF04" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xDEB" flags="0x30">
    <title>Idle Speed Control - Airflow Max (In Gear)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this table has 9 rows and 9 columns on this operating system (from its own table header, checked with its own lookup), where the H3 has 5 by 9; the text below describes the H3 layout. Maximum airflow the idle speed controller may command in in gear, by desired idle rpm (rows) and coolant (columns). Cold (below about 0 C) the window is wide open (0 to 31.9 g/s); warm, max and min sit close together, so these tables largely set warm idle airflow. The A/C offset is added on top. Effect: raise = more idle air at that desired rpm and coolant (keep max &gt;= min) Evidence: ledger:E0322, ledger:E1606</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-21" />
      <LABEL index="2" value="-2" />
      <LABEL index="3" value="17" />
      <LABEL index="4" value="36" />
      <LABEL index="5" value="55" />
      <LABEL index="6" value="74" />
      <LABEL index="7" value="93" />
      <LABEL index="8" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="550" />
      <LABEL index="1" value="650" />
      <LABEL index="2" value="750" />
      <LABEL index="3" value="850" />
      <LABEL index="4" value="950" />
      <LABEL index="5" value="1050" />
      <LABEL index="6" value="1150" />
      <LABEL index="7" value="1250" />
      <LABEL index="8" value="1350" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2259A" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDEC" flags="0x30">
    <title>Idle Speed Control - Airflow Max (P/N)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this table has 9 rows and 9 columns on this operating system (from its own table header, checked with its own lookup), where the H3 has 5 by 9; the text below describes the H3 layout. Maximum airflow the idle speed controller may command in Park/Neutral, by desired idle rpm (rows) and coolant (columns). Cold (below about 0 C) the window is wide open (0 to 31.9 g/s); warm, max and min sit close together, so these tables largely set warm idle airflow. The A/C offset is added on top. Effect: raise = more idle air at that desired rpm and coolant (keep max &gt;= min) Evidence: ledger:E0322, ledger:E1606</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-21" />
      <LABEL index="2" value="-2" />
      <LABEL index="3" value="17" />
      <LABEL index="4" value="36" />
      <LABEL index="5" value="55" />
      <LABEL index="6" value="74" />
      <LABEL index="7" value="93" />
      <LABEL index="8" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="550" />
      <LABEL index="1" value="650" />
      <LABEL index="2" value="750" />
      <LABEL index="3" value="850" />
      <LABEL index="4" value="950" />
      <LABEL index="5" value="1050" />
      <LABEL index="6" value="1150" />
      <LABEL index="7" value="1250" />
      <LABEL index="8" value="1350" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22432" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDED" flags="0x30">
    <title>Idle Speed Control - Airflow Min (In Gear)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this table has 9 rows and 9 columns on this operating system (from its own table header, checked with its own lookup), where the H3 has 5 by 9; the text below describes the H3 layout. Minimum airflow the idle speed controller may command in in gear, by desired idle rpm (rows) and coolant (columns). Cold (below about 0 C) the window is wide open (0 to 31.9 g/s); warm, max and min sit close together, so these tables largely set warm idle airflow. The A/C offset is added on top. Effect: raise = more idle air at that desired rpm and coolant (keep max &gt;= min) Evidence: ledger:E0322, ledger:E1606</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-21" />
      <LABEL index="2" value="-2" />
      <LABEL index="3" value="17" />
      <LABEL index="4" value="36" />
      <LABEL index="5" value="55" />
      <LABEL index="6" value="74" />
      <LABEL index="7" value="93" />
      <LABEL index="8" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="550" />
      <LABEL index="1" value="650" />
      <LABEL index="2" value="750" />
      <LABEL index="3" value="850" />
      <LABEL index="4" value="950" />
      <LABEL index="5" value="1050" />
      <LABEL index="6" value="1150" />
      <LABEL index="7" value="1250" />
      <LABEL index="8" value="1350" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22642" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDEE" flags="0x30">
    <title>Idle Speed Control - Airflow Min (P/N)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this table has 9 rows and 9 columns on this operating system (from its own table header, checked with its own lookup), where the H3 has 5 by 9; the text below describes the H3 layout. Minimum airflow the idle speed controller may command in Park/Neutral, by desired idle rpm (rows) and coolant (columns). Cold (below about 0 C) the window is wide open (0 to 31.9 g/s); warm, max and min sit close together, so these tables largely set warm idle airflow. The A/C offset is added on top. Effect: raise = more idle air at that desired rpm and coolant (keep max &gt;= min) Evidence: ledger:E0322, ledger:E1606</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-21" />
      <LABEL index="2" value="-2" />
      <LABEL index="3" value="17" />
      <LABEL index="4" value="36" />
      <LABEL index="5" value="55" />
      <LABEL index="6" value="74" />
      <LABEL index="7" value="93" />
      <LABEL index="8" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="550" />
      <LABEL index="1" value="650" />
      <LABEL index="2" value="750" />
      <LABEL index="3" value="850" />
      <LABEL index="4" value="950" />
      <LABEL index="5" value="1050" />
      <LABEL index="6" value="1150" />
      <LABEL index="7" value="1250" />
      <LABEL index="8" value="1350" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x224DA" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xDEF" flags="0x0">
    <title>Manual Downshift Pressure Adder - Time Limit (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. The adder ends once this time has passed since the downshift request (stock 0 s). Manual downshift pressure adder (switched off on the stock calibration): when the selector is moved to a low range soon after driving in 3rd or 4th, the downshift into 2nd gets extra pressure by turbine speed, held until the gear ratio reaches the 2nd gear level and then ramped out. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibratio...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3BC38" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDF0" flags="0x0">
    <title>Minimum RPM Run Latch</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. RPM threshold that permanently latches a run-detected flag for the remainder of the key cycle once engine speed climbs above it. Stock 50 rpm. Effect: raise = engine must spin faster before the latch sets; lower = the latch sets sooner Evidence: ledger:E0583, ledger:E1606</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x33460" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDF1" flags="0x0">
    <title>Misfire - Overspeed Pause Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: engine speed at or above which the overspeed pause is requested. The pause length is zero in the stock calibration, so this has no effect. Stock 7200 rpm. Effect: no effect while the overspeed pause length is zero Evidence: ledger:E1065, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xDF2" flags="0x30">
    <title>O2 Heater - Temperature per Ohm vs Learned Offset, Downstream</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor heater, downstream sensor: how many degrees the heater temperature estimate rises per ohm of heater resistance above nominal, chosen by the resistance offset stored by the cold-start learn. Stock 101 degC per ohm at an offset of -1.2 ohm and below rising to 145 at +0.6 ohm and above. Change only for a different sensor. Effect: raise = the heater temperature estimate rises faster with resistance Evidence: ledger:E1063, ledger:E1606</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>ohm (learned offset)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-3" />
      <LABEL index="1" value="-2.85" />
      <LABEL index="2" value="-2.7" />
      <LABEL index="3" value="-2.55" />
      <LABEL index="4" value="-2.4" />
      <LABEL index="5" value="-2.25" />
      <LABEL index="6" value="-2.1" />
      <LABEL index="7" value="-1.95" />
      <LABEL index="8" value="-1.8" />
      <LABEL index="9" value="-1.65" />
      <LABEL index="10" value="-1.5" />
      <LABEL index="11" value="-1.35" />
      <LABEL index="12" value="-1.2" />
      <LABEL index="13" value="-1.05" />
      <LABEL index="14" value="-0.9" />
      <LABEL index="15" value="-0.75" />
      <LABEL index="16" value="-0.6" />
      <LABEL index="17" value="-0.45" />
      <LABEL index="18" value="-0.3" />
      <LABEL index="19" value="-0.15" />
      <LABEL index="20" value="0" />
      <LABEL index="21" value="0.15" />
      <LABEL index="22" value="0.3" />
      <LABEL index="23" value="0.45" />
      <LABEL index="24" value="0.6" />
      <LABEL index="25" value="0.75" />
      <LABEL index="26" value="0.9" />
      <LABEL index="27" value="1.05" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.35" />
      <LABEL index="30" value="1.5" />
      <LABEL index="31" value="1.65" />
      <LABEL index="32" value="1.8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C82C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC per ohm</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xDF3" flags="0x0">
    <title>Output Speed Sensor - Pulse Loss Updates to Zero (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. With the pulse loss handling switched on, each update without an output shaft speed sensor pulse lowers the output speed reading to what one pulse over the elapsed time would mean, and after this many updates without a pulse the reading is 0. Stock 0. The pulse loss handling is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1511, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DF30" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDF4" flags="0x0">
    <title>P0014 Check - Desired Cam Steady Band</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam position check P0014: samples are only taken once the desired cam angle has stayed inside a spread smaller than this for the steady time. Stock 0.9 deg. Effect: raise = the desired cam angle may move more and still count as steady Evidence: ledger:E1057, ledger:E1820</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33470" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDF5" flags="0x0">
    <title>P0014 Check - Cam Error Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam position check P0014: filter on the cam error the check judges, as the fraction of the gap closed per update. Stock 1.0 (no filtering). Effect: lower = the cam error is smoothed before it is judged Evidence: ledger:E1057, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x336EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xDF6" flags="0x30">
    <title>P0230 Circuit Check - Fault Count and Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel pump relay circuit check P0230: the code sets once the first value&#x27;s number of faulted samples is reached; if the second value&#x27;s number of samples is reached first, the check passes and both counts start again. Stock 10 and 12. Effect: raise the first value = more faulted samples are needed to set the code; raise the second = each window is longer Evidence: ledger:E1058, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>value</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="fault samples to fail" />
      <LABEL index="1" value="window samples to pass" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3642C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xDF7" flags="0x0">
    <title>P0506 - Idle Spark Correction Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0506 (idle rpm lower than expected) counts toward a fail while the idle spark correction, the spark the PCM adds to pull a low idle back up, is above this. Stock 50 deg, which the stock idle spark curves (up to 21 deg) never reach. Effect: lower = P0506 can set at a smaller idle spark correction Evidence: ledger:E0990, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDF8" flags="0x0">
    <title>P0506 Idle Speed Low - Fail Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the idle speed must stay below the low speed error threshold before one P0506 fail period is counted. Stock 5 s. Part of the idle speed diagnostic (P0506 idle speed lower than expected, P0507 higher than expected), which runs only once its enable conditions are met. Effect: raise = longer underspeed needed per fail period Evidence: ledger:E0639, ledger:E1239, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3655C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDF9" flags="0x0">
    <title>P0506 / P0507 - Fail Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0506 / P0507 count a failure once the idle spark correction has stayed beyond its threshold for this long. Stock 12.75 s. Effect: raise = the idle speed codes take longer to set Evidence: ledger:E0990, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365C2" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDFA" flags="0x0">
    <title>P0507 Fail - Period Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0507 (idle rpm higher than expected) sets once this many fail periods have been counted (each period is one P0506 / P0507 fail time with the idle spark correction beyond its threshold). Stock 1. Effect: raise = more fail periods are needed to set P0507 Evidence: ledger:E1033, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDFB" flags="0x0">
    <title>P0507 Idle Speed High - Fail Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the idle speed must stay above the high speed error threshold before one P0507 fail period is counted. Stock 15 s. Part of the idle speed diagnostic (P0506 idle speed lower than expected, P0507 higher than expected), which runs only once its enable conditions are met. Effect: raise = longer overspeed needed per fail period Evidence: ledger:E0639, ledger:E1239, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3655A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDFC" flags="0x0">
    <title>P0507 - Idle Spark Correction Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0507 (idle rpm higher than expected) counts toward a fail while the idle spark correction, the spark the PCM removes to pull a high idle back down, is below this. Stock -20 deg, which the stock idle spark curves (down to -9 deg) never reach. Effect: raise (toward 0) = P0507 can set at a smaller idle spark correction Evidence: ledger:E0990, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x365C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDFD" flags="0x0">
    <title>P0641 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor reference voltage A check (P0641): the code also sets once this many samples in a counting window are out of range. Stock 20. Effect: raise = more out of range samples are needed to set the code Evidence: ledger:E1033, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x31970" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDFE" flags="0x0">
    <title>P0641 Fail - Continuous Fault Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor reference voltage A check (P0641): the code sets once the reference voltage has been out of range continuously for this long. Stock 0.2 s. Effect: raise = a longer continuous fault is needed to set the code Evidence: ledger:E1033, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3196C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDFF" flags="0x0">
    <title>P0641 Check - Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor reference voltage A check (P0641): the fault sample count starts again after this many samples. Stock 40. Effect: raise = each counting window is longer Evidence: ledger:E1033, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3196E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE00" flags="0x30">
    <title>P0650 Circuit Check - Fault Count and Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Malfunction indicator lamp circuit check P0650: the code sets once the first value&#x27;s number of faulted samples is reached; if the second value&#x27;s number of samples is reached first, the check passes and both counts start again. Stock 100 and 120. Effect: raise the first value = more faulted samples are needed to set the code; raise the second = each window is longer Evidence: ledger:E1058, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>value</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="fault samples to fail" />
      <LABEL index="1" value="window samples to pass" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33466" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE01" flags="0x0">
    <title>P0651 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor reference voltage B check (P0651): the code also sets once this many samples in a counting window are out of range. Stock 20. Effect: raise = more out of range samples are needed to set the code Evidence: ledger:E1033, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x31976" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE02" flags="0x0">
    <title>P0651 Fail - Continuous Fault Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor reference voltage B check (P0651): the code sets once the reference voltage has been out of range continuously for this long. Stock 0.2 s. Effect: raise = a longer continuous fault is needed to set the code Evidence: ledger:E1033, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x31972" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE03" flags="0x0">
    <title>P0651 Check - Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor reference voltage B check (P0651): the fault sample count starts again after this many samples. Stock 40. Effect: raise = each counting window is longer Evidence: ledger:E1033, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x31974" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE04" flags="0x0">
    <title>P0705 Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0705 (transmission range sensor circuit) reports a pass once the transmission range switch inputs have read a valid range for this long. Stock 5 s. Effect: raise = P0705 takes longer to report a pass Evidence: ledger:E0960, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F85A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE05" flags="0x0">
    <title>P0712 Pass - Sensor Resistance</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0712 (transmission fluid temperature sensor circuit low): sensor resistance at or above which the pass time runs. Stock 45 ohm. Effect: raise = the check needs a higher resistance to pass Evidence: ledger:E1093, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F796" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ohm</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>134217727.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE06" flags="0x0">
    <title>P0712 Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0712 (transmission fluid temperature sensor circuit low): time the resistance must stay at or above the pass limit to pass. Stock 10 s. Effect: lower = the check passes faster Evidence: ledger:E1093, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F78F" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE07" flags="0x0">
    <title>P0712 Fail - Sensor Resistance</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0712 (transmission fluid temperature sensor circuit low): sensor resistance at or below which the circuit is judged shorted. Stock 40 ohm (hotter than the 150 C end of the sensor table). Effect: lower = a lower resistance is tolerated Evidence: ledger:E1093, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F792" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ohm</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>134217727.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE08" flags="0x0">
    <title>P0713 Fail / Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0713 (transmission fluid temperature sensor circuit high): time the resistance must stay at or above the limit to set the code, and below it to pass. Stock 12.75 s (255 is the longest time, not off). Effect: lower = the code sets and clears faster Evidence: ledger:E1093, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F77E" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE09" flags="0x0">
    <title>P0713 Fail - Sensor Resistance</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0713 (transmission fluid temperature sensor circuit high): sensor resistance at or above which the circuit is judged open. Stock 111605 ohm (colder than the -40 C end of the sensor table). Effect: raise = a higher resistance is tolerated Evidence: ledger:E1093, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F786" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ohm</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>134217727.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE0A" flags="0x0">
    <title>P0742 Test - Run Condition, Engine Torque Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0742 (converter clutch stuck on) test: the test runs only with engine torque at or below this. Stock 525 Nm. Effect: lower = the test stops at lower torque Evidence: ledger:E0908, ledger:E0912, ledger:E1095, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F696" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE0B" flags="0x0">
    <title>P0742 Test - Run Condition, Engine Torque Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0742 (converter clutch stuck on) test: the test runs only with engine torque at or above this. Stock 70 Nm. Effect: raise = the test needs more engine torque Evidence: ledger:E0777, ledger:E0806, ledger:E1095, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F698" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE0C" flags="0x0">
    <title>P0742 Fail - Speed Ratio Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0742 (converter clutch stuck on) test: a failure can be scored only with the input / output speed ratio at or below this. Stock 1.350 (so in 3rd or 4th gear). The pass side does not look at the ratio. Effect: lower = failures are scored over a narrower ratio range Evidence: ledger:E0777, ledger:E0910, ledger:E0916, ledger:E1095, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F6C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE0D" flags="0x0">
    <title>P0742 Fail - Speed Ratio Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0742 (converter clutch stuck on) test: a failure can be scored only with the input / output speed ratio at or above this. Stock 0.650 (so in 3rd or 4th gear). The pass side does not look at the ratio. Effect: raise = failures are scored over a narrower ratio range Evidence: ledger:E0777, ledger:E0910, ledger:E0916, ledger:E1095, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F6CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE0E" flags="0x0">
    <title>P0742 Test - Run Condition, Fluid Temperature Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0742 (converter clutch stuck on) test: the test runs only with transmission fluid at or below this. Stock 130 C. Effect: lower = the test stops at lower fluid temperature Evidence: ledger:E0777, ledger:E0972, ledger:E1095, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F6D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE0F" flags="0x0">
    <title>P0742 Test - Run Condition, Fluid Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0742 (converter clutch stuck on) test: the test runs only with transmission fluid at or above this. Stock 20 C. Effect: raise = the test needs warmer fluid Evidence: ledger:E0777, ledger:E0972, ledger:E1095, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F6D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE10" flags="0x0">
    <title>P0742 Test - Run Condition, Throttle Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0742 (converter clutch stuck on) test: the test runs only with driver throttle at or below this. Stock 90 %. Effect: lower = the test stops at less throttle Evidence: ledger:E0777, ledger:E0972, ledger:E1095, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F6B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE11" flags="0x0">
    <title>P0742 Test - Run Condition, Throttle Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0742 (converter clutch stuck on) test: the test runs only with driver throttle at or above this. Stock 15 %. Effect: raise = the test needs more throttle Evidence: ledger:E0777, ledger:E0972, ledger:E1095, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F6B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE12" flags="0x0">
    <title>Trans Slip (P0894) Pass - Slip Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 50 rpm. The P0894 (transmission component slipping) test reports a pass once converter slip stays inside the pass window for the pass time, and clears its counts. Effect: raise = a pass is reported with more slip Evidence: ledger:E0849, ledger:E0877, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F712" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE13" flags="0x0">
    <title>Trans Slip (P0894) Pass - Slip Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock -10 rpm. The P0894 (transmission component slipping) test reports a pass once converter slip stays inside the pass window for the pass time, and clears its counts. Effect: lower = a pass is reported with more negative slip Evidence: ledger:E0849, ledger:E0877, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F714" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE14" flags="0x0">
    <title>Trans Slip (P0894) Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 5 s. The P0894 (transmission component slipping) test reports a pass once converter slip stays inside the pass window for the pass time, and clears its counts. Effect: raise = slip must stay in the pass window longer Evidence: ledger:E0849, ledger:E0877, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F73A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE15" flags="0x0">
    <title>Trans Slip (P0894) Stages - Throttle Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 10 %. P0894 (transmission component slipping) stages: after the first count, three stages run in turn, each needing converter slip inside its own window for its own time with the throttle request inside the stage throttle window; when stage 3 completes the PCM reports P0894. Effect: raise = the stages need a larger throttle request Evidence: ledger:E0786, ledger:E0849, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F720" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE16" flags="0x0">
    <title>P1810 Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1810: time without the fault condition that passes the check. Stock 5 s. Effect: raise = the check takes longer to pass Evidence: ledger:E1094, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F854" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE17" flags="0x0">
    <title>P1815 Fail - Input Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1815 (engine started with the range switch not in park or neutral): after the start the fault time runs only with transmission input speed at or above this. Stock 0 rpm (always). Effect: raise = the fault time needs more input speed Evidence: ledger:E1294, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F8B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE18" flags="0x0">
    <title>P1816 Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1816 (fluid pressure switch reads park / neutral in 4th gear) check: time the pressure switch must read D4 while the check runs to pass. Stock 2 s. Effect: raise = the check takes longer to pass Evidence: ledger:E1101, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F892" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE19" flags="0x0">
    <title>P1818 Test - Output Speed Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. P1818 (pressure switch shows a drive range with the reverse ratio): runs only with transmission output speed at or above this. Stock 8191.9 rpm. The check is switched off on this truck and its code is disabled, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1322, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F87A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE1A" flags="0x0">
    <title>Pressure Switch Position Checks - Reverse Ratio Window Low (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Bottom of the reverse gear ratio window of the pressure switch position checks. Stock 2.230. It is read only by checks that are switched off on this truck (P1817, P1818, P1826 and an unused P1816 path), so it has no effect. Effect: no effect on this truck Evidence: ledger:E0340, ledger:E0767, ledger:E0813, ledger:E0910, ledger:E1101, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F864" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE1B" flags="0x30">
    <title>Pre-Sync Start Pulses - Minimum Engine-Off Time vs Coolant (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. At key-on the sequence is allowed only when the engine has been off for longer than this (stock 0 s). Pre-sync start pulses: an optional sequence of fuel pulses at cranking, before the PCM has synchronised to the crankshaft. It is switched off on this calibration, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = needs a longer engine-off time) Evidence: ledger:E1387, ledger:E1606</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x26CE4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25648" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE1C" flags="0x0">
    <title>Road Load Model - Rolling Radius Learn Weight (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Share of each new rolling radius sample (radius x wheel speed / transmission output speed) taken into the learned radius. Stock 0. Part of the road load model the shift sequencing uses to estimate grade and road load. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1485, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2E0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE1D" flags="0x0">
    <title>3-2 Shift Solenoid - On in 3rd / 4th Above (fluid temp)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Outside a 2-1 downshift the 3-2 shift solenoid is commanded on in 3rd and 4th gear once transmission fluid temperature is at or above this, and off below it or in 1st and 2nd. Stock 40 C. Effect: raise = the 3-2 solenoid stays off in 3rd / 4th until the fluid is warmer Evidence: ledger:E1298, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x375C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE1E" flags="0x0">
    <title>Shift Engine Speed Predictor - Stop Below Turbine Speed Error (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. The correction passes stop once the turbine speed error is below this. Stock 4096 rpm. During a shift the PCM can predict the engine speed the shift ends at: a first guess, then correction passes that compare the turbine speed the converter model expects at the predicted engine speed with the measured turbine speed. The prediction is only used by alternative torque calculations that are switched off on the stock calibration. This has no effect on the stock c...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E3EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>16383.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE1F" flags="0x30">
    <title>Base Shift Pressure vs Torque - 4WD Low (1-2 / 2-3 / 3-4)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base pressure commanded during an upshift, by shift torque (columns) and upshift (rows), in the upshift pressure source used on the stock calibration; this is set 2 (4WD Low on the stock calibration). 1 count = 4 kPa = 0.58 psi. Which set each drive mode uses is chosen by Shift Set by Drive Mode. Effect: 4WD Low upshift firmness (higher = firmer, shorter shifts) Evidence: ledger:E0235, ledger:E0237, ledger:E1311, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3E3FA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT; data columns: shift torque (Nm))</units>
      <embedinfo type="1" />
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A2C8" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>psi</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>147.938454</max>
      <MATH equation="X*0.5801508"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE20" flags="0x0">
    <title>TCC Slip On Target - Alternate Entry Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. With the slip target cap turned on, slip must stay within the alternate entry margin this long before the PCM moves to on target (stock 0 s). This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1309, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D1AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE21" flags="0x0">
    <title>TCC Release - Closed Throttle Above Low Speed, On Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Above the low speed window, below this throttle the closed throttle release turns on (stock 0 %: never). The converter clutch is released while the closed throttle condition is active (where enabled for the current range and gear). This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = release the clutch on closed throttle at higher speeds too) Evidence: ledger:E1302, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D220" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE22" flags="0x0">
    <title>TCC Slip Target Floor - Hold After A/C Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The minimum TCC slip target applies while the A/C compressor runs and for this time after it turns off (stock 0 s: it ends with the compressor). Effect: raise = the higher minimum slip lasts longer after the A/C turns off Evidence: ledger:E1385, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D4A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE23" flags="0x30">
    <title>Trans Fluid Temp Sensor - Resistance Points</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor resistance at each of the 33 temperature points of the fluid temperature sensor (stock 47 ohm at 150 C to 100.7 kohm at -40 C, the standard GM thermistor). Paired with Trans Fluid Temp Sensor - Temperature Points. Change only for a different sensor (E0342). Effect: reported and used transmission fluid temperature Evidence: ledger:E0342, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3DDE4" mmedelementsizebits="32" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ohm</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>134217727.968750</max>
      <MATH equation="X/32"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE24" flags="0x0">
    <title>Torque Model - Engine Acceleration Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque model: share of each new engine acceleration reading taken into the filtered acceleration that the inertia torque is worked out from. Stock 0.5; 1.0 = no filtering. Effect: raise = the inertia torque follows engine speed changes faster Evidence: ledger:E1114, ledger:E1606</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x303CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE25" flags="0x0">
    <title>Torque Reduction Cylinder Cut - Restore Hysteresis (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Torque reduction with cylinder cut: a cut cylinder is given back only when the torque request needs this much more than the cylinders now fuelled. Stock 0.25 of a cylinder. Dormant on the stock calibration: the fewest fuelled cylinders curve is 5 everywhere, so no cylinder is ever cut. Effect: raise = cut cylinders come back later Evidence: ledger:E1133, ledger:E1606</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x313C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cylinders</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE26" flags="0x0">
    <title>Trans Abuse Mode - Input Speed Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Trans abuse mode: with the alternate speed source selected, an engagement counts as abuse only at or above this transmission input speed. Stock 0 rpm. The alternate source is not selected on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1378, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3EA8E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE27" flags="0x30">
    <title>Transmission Input Torque Limit - Input Speed Breakpoints, 4th Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Transmission input speed points of the 4th gear input torque limit curves. Stock 0 to 6400 rpm in 800 rpm steps. The limit they belong to never arms on this calibration. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E1177, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3ED42" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE28" flags="0x0">
    <title>Trans Range Switch - Alternate Decode Confirm Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Alternate range switch decode: a new range switch reading must last this long before it is accepted. Stock 0.025 s. This has no effect on the stock calibration (dormant): the alternate decode is not used on this truck. Effect: no effect on the stock calibration Evidence: ledger:E1319, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3E946" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE29" flags="0x30">
    <title>Trans Range Switch - Alternate Decode Code Map (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Alternate range switch decode: maps the 4-input range switch code (0 to 15) to the alternate decode&#x27;s range code. Used only when the alternate decode is switched on, which it is not on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1491, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>16</indexcount>
      <units>range switch input code</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E948" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>code</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE2A" flags="0x0">
    <title>Mass Estimator - Learn Count Reset Time Below Minimum Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Time below the minimum speed after which the learn count resets, so the first weight curve is used again. Stock 0. Part of the vehicle mass estimator in the road load model the shift sequencing uses. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0779, ledger:E1487, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F2FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE2B" flags="0x30">
    <title>Transmission Torque Loss vs Turbine Speed and Fluid Temp - 4th Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque the transmission loses in 4th gear, by turbine speed (rows) and fluid temperature (columns). Half of it is taken off the gearbox torque before it is multiplied up to the axle torque the road load estimate uses. Stock 0 everywhere: no loss is taken off. Effect: raise = a lower axle torque estimate for the road load estimate in that gear Evidence: ledger:E1439, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>degC (trans fluid)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="40" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>rpm (turbine)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="600" />
      <LABEL index="1" value="1800" />
      <LABEL index="2" value="3000" />
      <LABEL index="3" value="4200" />
      <LABEL index="4" value="5400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E2F4" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE2C" flags="0x30">
    <title>Trans Engine Torque Override vs Throttle (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Engine torque the transmission uses in place of its filtered engine torque while the torque filter gate is met, by throttle demand (0 to 100 %). Stock 0. Dormant: the gate thresholds are 0, so the gate is never met and this has no effect on this truck&#x27;s software. Effect: sets the engine torque the transmission uses while the override is active Evidence: ledger:E1233, ledger:E1606</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>%</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="25" />
      <LABEL index="2" value="50" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E338" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE2D" flags="0x0">
    <title>VE Transient Mode - Window Entry Pressure Sum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While the transient mode is off, it starts when the manifold pressure change from the window start, summed over the window&#x27;s updates, rises above this (stock 1.5 kPa). Part of the window check of the volumetric efficiency transient mode, which runs only when its throttle gate is open; on the stock calibration that gate is closed, so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0780, ledger:E0854, ledger:E1429, ledger:E1606</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4DA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE2E" flags="0x0">
    <title>VE Transient Mode - Window Entry Length (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of model updates the summed manifold pressure change is collected before the window starts again while the transient mode is off (stock 4). Part of the window check of the volumetric efficiency transient mode, which runs only when its throttle gate is open; on the stock calibration that gate is closed, so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E1429, ledger:E1606</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C4D8" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE2F" flags="0x0">
    <title>Secondary Air - Fallback Run Time, Warm</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Secondary air run time used at or above the fallback coolant limit when the catalyst temperature curves are not used. Stock 0 s. Secondary air injection is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0573, ledger:E0836, ledger:E1193, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA30" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE30" flags="0x0">
    <title>Secondary Air - Fallback Fuel Correction Time, Warm</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Secondary air fuel correction time used at or above the fallback coolant limit when the catalyst temperature curves are not used. Stock 0 s. Secondary air injection is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0573, ledger:E0836, ledger:E1193, ledger:E1606</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CA34" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE31" flags="0x0">
    <title>2-1 Downshift Fixed Pressure - Engine Off or Solenoid Fault</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fixed 2-1 downshift pressure used instead of the pressure tables while the engine is not running or the shift timing solenoid fault reaction (P0787 / P0788) is active. Stock 5.1 psi (35 kPa). This reaction also runs while the transmission range switch reading is invalid (no valid range for the confirm time). Effect: raise = more pressure on a 2-1 downshift in those two cases Evidence: ledger:E0334, ledger:E0987, ledger:E1476, ledger:E1618</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x375C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>psi</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>594.066911</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*0.00906488"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE32" flags="0x0">
    <title>First-Run Mode - Start-Up Coolant Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First-run mode runs only during the first 12 s of engine running recorded by the PCM (kept through power-off), with a stored flag set, the mode enable set and start-up coolant inside the coolant window. This is the highest start-up coolant temperature it accepts. Stock 50 C. Effect: raise = first-run mode also runs on warmer starts Evidence: ledger:E0436, ledger:E1227, ledger:E1618</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x26CDC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE33" flags="0x0">
    <title>First-Run Mode - Start-Up Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First-run mode runs only during the first 12 s of engine running recorded by the PCM (kept through power-off), with a stored flag set, the mode enable set and start-up coolant inside the coolant window. This is the lowest start-up coolant temperature it accepts. Stock 10 C. Effect: lower = first-run mode also runs on colder starts Evidence: ledger:E0436, ledger:E1227, ledger:E1618</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x26CDE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE34" flags="0x0">
    <title>First-Run Mode - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First-run mode runs only during the first 12 s of engine running recorded by the PCM (kept through power-off), with a stored flag set, the mode enable set and start-up coolant inside the coolant window. This switch allows it (1) or not (0). Stock 1. Effect: 0 = first-run mode never runs Evidence: ledger:E0436, ledger:E1227, ledger:E1577, ledger:E1618</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x26CDA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>switch</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE35" flags="0x30">
    <title>Idle Airflow vs RPM Below Desired</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added only when engine rpm is below desired idle (droop catch), vs how far below after the droop gain. Stock 0 up to 175 rpm of droop, then rising to 5.0 g/s at 400 rpm. Row 1 = In Gear, row 2 = Park/Neutral. Effect: raise = stronger catch when idle sags (stall resistance); too much makes idle hunt Evidence: ledger:E0286, ledger:E0287, ledger:E1618</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29D7E" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE36" flags="0x0">
    <title>P0712 Fail - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0712 (transmission fluid temperature sensor circuit low): time the resistance must stay at or below the fail limit to set the code. Stock 12.75 s (255 is the longest time, not off). Effect: lower = the code sets faster Evidence: ledger:E1093, ledger:E1618</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F78E" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE37" flags="0x0">
    <title>P0741 Test - Run Condition, Throttle Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0741 (converter clutch stuck off) test: the test runs only with driver throttle at or below this. Stock 100 %: no upper limit. Effect: lower = the test stops at less throttle Evidence: ledger:E0777, ledger:E0973, ledger:E1095, ledger:E1618</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F6B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE38" flags="0x0">
    <title>P0741 Test - Run Condition, Throttle Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0741 (converter clutch stuck off) test: the test runs only with driver throttle at or above this. Stock 20 %. Effect: raise = the test needs more throttle Evidence: ledger:E0777, ledger:E0972, ledger:E1095, ledger:E1618</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F6B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE39" flags="0x0">
    <title>P1380 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1380 sets once this many test samples had no valid rough road data while a misfire (P0300) is flagged. Stock 40. Effect: raise = more samples without rough road data are needed to set P1380 Evidence: ledger:E1038, ledger:E1618</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE3A" flags="0x0">
    <title>P1381 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1381 sets once this many test samples were counted with the rough road data source silent while a misfire (P0300) is flagged. Stock 20. Effect: raise = more silent samples are needed to set P1381 Evidence: ledger:E1038, ledger:E1618</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE3B" flags="0x0">
    <title>Pressure Switch Position Checks - Reverse Ratio Window High (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Top of the reverse gear ratio window of the pressure switch position checks. Stock 2.360. It is read only by checks that are switched off on this truck (P1817, P1818, P1826 and an unused P1816 path), so it has no effect. Effect: no effect on this truck Evidence: ledger:E0340, ledger:E0767, ledger:E0813, ledger:E0910, ledger:E1101, ledger:E1618</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F862" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE3C" flags="0x30">
    <title>Shift Pressure Multiplier 2-3</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift pressure multiplier for the 2-3 shift by shift torque and an engine-side ratio (stock 1.0 with a 0.875 diagonal band). Header [17][17], never edit it. Multiplies base shift pressure only when the enable is set; stock 0, so unused on the H3. Effect: shift firmness Evidence: ledger:E0368, ledger:E0710, ledger:E1565, ledger:E1618</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3E3FE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>shift torque (Nm)</units>
      <embedinfo type="1" />
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x3E3C0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>ratio (trans input torque / shift torque adder)</units>
      <embedinfo type="1" />
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3B760" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE3D" flags="0x30">
    <title>TCC Apply Start Offset - 2-3 Shift Index</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the converter clutch starts to apply, its pressure starts this much below the load based pressure, then the slip controller brings it up (never below zero pressure). By vehicle speed and engine torque, for the 2-3 shift index. Stock 0. Effect: raise = softer start of the apply (lower first pressure) Evidence: ledger:E1421, ledger:E1618</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x3CE82" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>5</indexcount>
      <units>Nm (positive net engine torque)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="32" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="96" />
      <LABEL index="4" value="128" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="192" />
      <LABEL index="7" value="224" />
      <LABEL index="8" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3CF66" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE3E" flags="0x0">
    <title>Cold Start Emission Monitor - Coolant Latch Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. Below this coolant temperature the monitor keeps the highest coolant temperature seen and looks up the expected idle speed with it; at or above it the current coolant temperature is used (stock minus 39 C). Part of the cold start emission monitor (fault code P1400), which checks that the engine runs the warm-up idle speed and spark timing after a cold start. On this calibration the...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33246" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE3F" flags="0x0">
    <title>Cold Start Emission Monitor - Expected Idle Speed, Vehicle Speed Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. The expected idle speed is set only while vehicle speed is below this value (and throttle below its own limit); otherwise it is set to zero (stock 2 km/h). Part of the cold start emission monitor (fault code P1400), which checks that the engine runs the warm-up idle speed and spark timing after a cold start. On this calibration the monitor is switched off and its tables are not size...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x331F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE40" flags="0x0">
    <title>Cold Start Emission Monitor - Expected Idle Speed, Throttle Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. The expected idle speed is set only while throttle is below this value (and vehicle speed below its own limit); otherwise it is set to zero (stock 2 %). Part of the cold start emission monitor (fault code P1400), which checks that the engine runs the warm-up idle speed and spark timing after a cold start. On this calibration the monitor is switched off and its tables are not sized,...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x331F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE41" flags="0x30">
    <title>Cruise Control - Target Ramp-Down Step vs MAP x Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Largest step per pass by which the cruise control demand may fall toward the Cruise Control Demand Target table, by engine load (MAP, rows) and vehicle speed (columns, 38 to 180 km/h). The step is this value times a separate scale that is 0 on the stock calibration, so the limit is never applied: this has no effect on the stock calibration (dormant). Values are the controller&#x27;s internal demand counts. Shown raw. DO NOT EDIT. Effect: no effect on the sto...</description>
    <CATEGORYMEM index="0" category="9" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.9" />
      <LABEL index="2" value="55.8" />
      <LABEL index="3" value="64.6" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.4" />
      <LABEL index="6" value="91.2" />
      <LABEL index="7" value="100.1" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.9" />
      <LABEL index="10" value="126.8" />
      <LABEL index="11" value="135.6" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.4" />
      <LABEL index="14" value="162.2" />
      <LABEL index="15" value="171.1" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22006" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE42" flags="0x30">
    <title>Manual Downshift Pressure Adder - Ramp-Out Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Time over which the adder ramps out to zero, by turbine speed (stock 0 s: removed at once). Manual downshift pressure adder (switched off on the stock calibration): when the selector is moved to a low range soon after driving in 3rd or 4th, the downshift into 2nd gets extra pressure by turbine speed, held until the gear ratio reaches the 2nd gear level and then ramped out. This has no effect on the stock calibration (dormant). Effect: no effect on the stock...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3BC6C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE43" flags="0x0">
    <title>Manual Range 3rd Hold - High Slip Hold Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. With high converter slip, 3rd is held at or above this vehicle speed (stock 500 km/h). Manual range 3rd gear hold: after the selector is moved out of Drive while in 4th to a low range that would allow 2nd or 1st, a downshift to 3rd is kept in 3rd (no further downshift) while vehicle speed is high. The stock speed limit is 500 km/h, so the hold never applies (dormant). Effect: no eff...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x39DDA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE44" flags="0x30">
    <title>Road Load Model - Lower Top Gear Cap Below Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. The top gear cap is only lowered below this speed, by current gear; it then becomes one gear below the current gear. Part of the road load model, which lowers the highest gear the transmission may use (the top gear cap) on grades or with a heavy load and raises it again when the load eases. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1498, ledger:E1626</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38490" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE45" flags="0x0">
    <title>Road Load Model - Lowest Top Gear Cap (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. The top gear cap is never lowered below this gear (stock 6, above 4th, so it is never lowered). Part of the road load model, which lowers the highest gear the transmission may use (the top gear cap) on grades or with a heavy load and raises it again when the load eases. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1498, ledger:E1626</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x38438" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gear</units>
    <decimalpl>0</decimalpl>
    <min>1.000000</min>
    <max>65536.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X+1"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE46" flags="0x30">
    <title>Road Load Model - Raise Top Gear Cap Above Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Above this speed the top gear cap is raised by one gear, by current gear. Part of the road load model, which lowers the highest gear the transmission may use (the top gear cap) on grades or with a heavy load and raises it again when the load eases. The model is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1030, ledger:E1498, ledger:E1626</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38488" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE47" flags="0x0">
    <title>Shift Lamp - Vehicle Speed Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Shift lamp request (a data bus signal for a manual transmission upshift lamp): no lamp request below this vehicle speed. Stock 13 km/h. Dormant on this truck: the shift lamp request only runs on the manual transmission software path. Effect: no effect on this truck Evidence: ledger:E1143, ledger:E1626</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2CA8E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE48" flags="0x0">
    <title>TCC Release - Closed Throttle Above Low Speed, Off Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Above the low speed window, above this throttle the closed throttle release turns off (stock 0 %). The converter clutch is released while the closed throttle condition is active (where enabled for the current range and gear). This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1302, ledger:E1626</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D222" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE49" flags="0x0">
    <title>Trans Fluid Temp Substitute - Cold Intake Air Adder (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Added to the estimated fluid temperature while intake air is below the cold intake air threshold. Stock 0 C. Used only when the fluid temperature sensor has a fault and the fluid temperature is estimated from coolant temperature (coolant between the very cold and hot engine thresholds, after the early run time). This has no effect on the stock calibration (dormant). While the transmission range switch reading is invalid the substitute is the Invalid Range Sw...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DECA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE4A" flags="0x0">
    <title>Trans Fluid Temp Substitute - Warm Intake Air Adder (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Added to the estimated fluid temperature while intake air is above the warm intake air threshold. Stock 0 C. Used only when the fluid temperature sensor has a fault and the fluid temperature is estimated from coolant temperature (coolant between the very cold and hot engine thresholds, after the early run time). This has no effect on the stock calibration (dormant). While the transmission range switch reading is invalid the substitute is the Invalid Range Sw...</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3DECE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE4B" flags="0x30">
    <title>Tip-In Spark Advance - RPM Factor (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Tip-in spark advance (spark advance added for a short time when cylinder airmass jumps): factor on the advance amount by engine speed, applied once coolant and run time are above their limits. Stock 1.0 up to 1200 rpm falling to 0.05 at high speed. Dormant on the stock calibration: the advance amount table is all zero and the trigger threshold is out of reach. Effect: raise = more of the advance is kept at that engine speed Evidence: ledger:E1142, ledger:E1626</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CD5C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE4C" flags="0x30">
    <title>Tip-In Spark Advance - Engine-Off Time Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. Tip-in spark advance (spark advance added for a short time when cylinder airmass jumps): factor on the advance amount by how long the engine was off before this start, applied while coolant is at or below its limit. Stock 0.25 for a restart, 0.63 after half an hour, 1.0 from one hour. Dormant on the stock calibration: the advance amount table is all zero and the trigger threshold is...</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>s engine-off time</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1800" />
      <LABEL index="2" value="3600" />
      <LABEL index="3" value="5400" />
      <LABEL index="4" value="7200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CD84" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE4D" flags="0x0">
    <title>Tip-In Spark Advance - Soak Factor Coolant At or Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Tip-in spark advance: the engine-off time factor is applied to the advance only while coolant is at or below this. Stock 70 C. Dormant on the stock calibration: the advance amount table is all zero and the trigger threshold is out of reach. Effect: raise = the soak factor also applies on a warmer engine Evidence: ledger:E1142, ledger:E1626</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2CD7E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE4E" flags="0x30">
    <title>Transmission Input Torque Limit - Input Speed Breakpoints, 2nd Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. Transmission input speed points of the 2nd gear input torque limit curves. Stock 0 to 6400 rpm in 800 rpm steps. The limit they belong to never arms on this calibration. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E1177, ledger:E1626</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3ED1A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE4F" flags="0x30">
    <title>Transmission Input Torque Limit - Input Speed Breakpoints, 3rd Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Transmission input speed points of the 3rd gear input torque limit curves. Stock 0 to 6400 rpm in 800 rpm steps. The limit they belong to never arms on this calibration. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E1177, ledger:E1626</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3ED2E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE50" flags="0x30">
    <title>2-1 Downshift Pressure Adder vs Speed vs RPM (above 38.5 mph)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the 2-1 downshift pressure for a downshift that starts above 38.5 mph (62 km/h), by the speed (rows) and engine rpm (columns) when the downshift began, after the baro and IAT multipliers; negative values reduce it. Stock all 0. Active only during a 2-1 downshift, which replaces the normal shift pressure. Effect: raise = firmer 2-1 downshift at that speed and engine rpm Evidence: ledger:E0334, ledger:E0335, ledger:E1155, ledger:E1630</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x37C26" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>rpm (engine speed when the 2-1 downshift started)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>mph (speed when the 2-1 downshift started)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="44.7" />
      <LABEL index="1" value="46.9" />
      <LABEL index="2" value="48.5" />
      <LABEL index="3" value="50.6" />
      <LABEL index="4" value="52.8" />
      <LABEL index="5" value="55.0" />
      <LABEL index="6" value="57.2" />
      <LABEL index="7" value="59.3" />
      <LABEL index="8" value="61.5" />
      <LABEL index="9" value="63.7" />
      <LABEL index="10" value="65.9" />
      <LABEL index="11" value="68.0" />
      <LABEL index="12" value="70.2" />
      <LABEL index="13" value="72.4" />
      <LABEL index="14" value="74.6" />
      <LABEL index="15" value="76.7" />
      <LABEL index="16" value="79.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x375D3" mmedelementsizebits="8" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>psi</units>
      <decimalpl>1</decimalpl>
      <min>-74.259328</min>
      <max>73.679177</max>
      <MATH equation="X*0.580151"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE51" flags="0x30">
    <title>2-1 Downshift Pressure Adder vs Speed vs RPM (up to 38.5 mph)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the 2-1 downshift pressure for a downshift that starts at or below 38.5 mph (62 km/h), by the speed (rows) and engine rpm (columns) when the downshift began, after the baro and IAT multipliers; negative values reduce it. Stock all 0. Active only during a 2-1 downshift, which replaces the normal shift pressure. Effect: raise = firmer 2-1 downshift at that speed and engine rpm Evidence: ledger:E0334, ledger:E0335, ledger:E1155, ledger:E1630</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x37C4A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>rpm (engine speed when the 2-1 downshift started)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>mph (speed when the 2-1 downshift started)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="15.5" />
      <LABEL index="1" value="17.1" />
      <LABEL index="2" value="18.6" />
      <LABEL index="3" value="20.2" />
      <LABEL index="4" value="21.7" />
      <LABEL index="5" value="23.3" />
      <LABEL index="6" value="24.9" />
      <LABEL index="7" value="26.4" />
      <LABEL index="8" value="28.0" />
      <LABEL index="9" value="29.5" />
      <LABEL index="10" value="31.1" />
      <LABEL index="11" value="32.6" />
      <LABEL index="12" value="34.2" />
      <LABEL index="13" value="35.7" />
      <LABEL index="14" value="37.3" />
      <LABEL index="15" value="38.8" />
      <LABEL index="16" value="40.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x376FB" mmedelementsizebits="8" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>psi</units>
      <decimalpl>1</decimalpl>
      <min>-74.259328</min>
      <max>73.679177</max>
      <MATH equation="X*0.580151"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE52" flags="0x0">
    <title>P0615 Test - Engine Speed Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12627882: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. The P0615 starter relay circuit check only runs at or above this engine speed. Stock 0 rpm. The check is switched off on the H3, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = the starter relay circuit check needs a higher engine speed) Evidence: ledger:E0620, ledger:E0717, ledger:E0733, ledger:E1364, ledger:E1635</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37558" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE53" flags="0x30">
    <title>Downshift Pressure Temp Modifier (alternate pressure mode) - Gear 3</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pressure added to the base shift pressure during a downshift, by base shift pressure (rows) and transmission fluid temperature (columns); the downshift counterpart of the Upshift Pressure Temp Modifier tables. The controller picks the table by its gear index during the downshift; this one is used while that index is 3rd gear, in a third shift pressure mode. Stock all 0 (no change). Effect: positive = firmer downshift at that temperature and base pressure, negative = softer Evidence: ledger:E0237, ledger:E1170, ledger:E1635</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (trans temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>kPa (base shift pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="160" />
      <LABEL index="2" value="320" />
      <LABEL index="3" value="480" />
      <LABEL index="4" value="640" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3B466" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE54" flags="0x30">
    <title>WOT Shift Speed - Normal</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 2][2 values]; COUNT is a structure word - never edit it (E0180). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Speed-based shift points used in the WOT mode of the Normal schedule (flat over throttle). 311 mph = no speed-based shift. (E0180) The PCM reads only the 100 column: this lookup runs at a fixed full-throttle input, so editing the 0 column has no effect (E0269). The PCM uses the Normal schedules in ordinary driving: not in hot transmission mode, cruise or 4-Lo. The wide-open-throttle set applies while pedal demand is above the high pedal set point (stock 96.9 %, 56.3 % in 4-Lo, 99 % with cruise engaged). Effect: WOT shift behaviour - chan...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>6</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2 up" />
      <LABEL index="1" value="2-3 up" />
      <LABEL index="2" value="3-4 up" />
      <LABEL index="3" value="2-1 down" />
      <LABEL index="4" value="3-2 down" />
      <LABEL index="5" value="4-3 down" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39A10" mmedelementsizebits="16" mmedrowcount="6" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE55" flags="0x30">
    <title>P0615 Circuit Check - Fault Count and Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter relay circuit check P0615 (this code is switched off in the stock calibration): the code sets once the first value&#x27;s number of faulted samples is reached; if the second value&#x27;s number of samples is reached first, the check passes and both counts start again. Stock 10 and 12. Effect: raise the first value = more faulted samples are needed to set the code; raise the second = each window is longer Evidence: ledger:E1058, ledger:E1635</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>value</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="fault samples to fail" />
      <LABEL index="1" value="window samples to pass" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37554" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE56" flags="0x0">
    <title>P0621 Fail - Time, Engine Running</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0621 (generator lamp control circuit) engine-running check: P0621 sets once the check has run with the engine running and its condition met for this long. Stock 15 s. Effect: raise = the engine-running check takes longer to set P0621 Evidence: ledger:E0909, ledger:E0958, ledger:E1635</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20838" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE57" flags="0x0">
    <title>P0741 Test - Run Condition, Engine Torque Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0741 (converter clutch stuck off) test: the test runs only with engine torque at or below this. Stock 525 Nm. Effect: lower = the test stops at lower torque Evidence: ledger:E0777, ledger:E0972, ledger:E1095, ledger:E1635</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F69A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE58" flags="0x0">
    <title>P0741 Test - Run Condition, Engine Torque Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0741 (converter clutch stuck off) test: the test runs only with engine torque at or above this. Stock 55 Nm. Effect: raise = the test needs more engine torque Evidence: ledger:E0777, ledger:E0806, ledger:E1095, ledger:E1635</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F69C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE59" flags="0x0">
    <title>P0741 Test - Run Condition, Fluid Temperature Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0741 (converter clutch stuck off) test: the test runs only with transmission fluid at or below this. Stock 150 C. Effect: lower = the test stops at lower fluid temperature Evidence: ledger:E0777, ledger:E0972, ledger:E1095, ledger:E1635</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3F6CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE5A" flags="0x0">
    <title>P0741 Test - Run Condition, Fluid Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0741 (converter clutch stuck off) test: the test runs only with transmission fluid at or above this. Stock 20 C. Effect: raise = the test needs warmer fluid Evidence: ledger:E0777, ledger:E0973, ledger:E1095, ledger:E1635</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F6CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE5B" flags="0x0">
    <title>P1380 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1380 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 50. Effect: raise = P1380 needs more samples before it passes Evidence: ledger:E0907, ledger:E1635</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE5C" flags="0x30">
    <title>Base Shift Pressure - Alternate (Power-On Upshift into Top Gear)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE=2][17 points]; COUNT and TYPE are structure bytes, never edit them (E0400). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base shift pressure used instead of the main table in a power-on upshift into the highest gear the selected range allows, from the start of the shift (and from a tip-in during such an upshift; in back-to-back upshifts after the Upshift Alternate Pressure times). Rows: set 0 / 1 / 2 (Shift Set by Drive Mode) x shift 1-2 / 2-3 / 3-4, by shift torque. 1 count = 4 kPa. Effect: firmness of power-on upshifts into top gear Evidence: ledger:E0235, ledger:E0400, ledger:E1030, ledger:E1295, ledger:E1509, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="55" />
      <LABEL index="4" value="110" />
      <LABEL index="5" value="165" />
      <LABEL index="6" value="220" />
      <LABEL index="7" value="275" />
      <LABEL index="8" value="330" />
      <LABEL index="9" value="385" />
      <LABEL index="10" value="440" />
      <LABEL index="11" value="495" />
      <LABEL index="12" value="550" />
      <LABEL index="13" value="605" />
      <LABEL index="14" value="660" />
      <LABEL index="15" value="715" />
      <LABEL index="16" value="770" />
      <LABEL index="17" value="825" />
      <LABEL index="18" value="880" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>set / shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="s0 1-2" />
      <LABEL index="1" value="s0 2-3" />
      <LABEL index="2" value="s0 3-4" />
      <LABEL index="3" value="s1 1-2" />
      <LABEL index="4" value="s1 2-3" />
      <LABEL index="5" value="s1 3-4" />
      <LABEL index="6" value="s2 1-2" />
      <LABEL index="7" value="s2 2-3" />
      <LABEL index="8" value="s2 3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A376" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>1020.000000</max>
      <MATH equation="X*4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE5D" flags="0x30">
    <title>Converter Model - Expected Speed Ratio vs Capacity Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Expected converter speed ratio for a given capacity factor (stock 0.25 at low factor to 0.98). Compared directly with the measured speed ratio. Part of the torque converter model check: the PCM computes a converter capacity factor (engine speed over the square root of the torque going through the converter fluid, in rpm per square root of Nm), predicts the converter speed ratio from it and flags a mismatch when the measured speed ratio falls outside the band. Effect: converter model mismatch flag Evidence: ledger:E0348, ledger:E1238, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm/sqrt(Nm)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="123.972" />
      <LABEL index="1" value="126.972" />
      <LABEL index="2" value="129.972" />
      <LABEL index="3" value="134.972" />
      <LABEL index="4" value="138.472" />
      <LABEL index="5" value="140.972" />
      <LABEL index="6" value="144.472" />
      <LABEL index="7" value="146.472" />
      <LABEL index="8" value="147.972" />
      <LABEL index="9" value="149.472" />
      <LABEL index="10" value="151.472" />
      <LABEL index="11" value="152.972" />
      <LABEL index="12" value="155.972" />
      <LABEL index="13" value="158.972" />
      <LABEL index="14" value="161.972" />
      <LABEL index="15" value="164.972" />
      <LABEL index="16" value="167.972" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3E9F8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>speed ratio (turbine / engine)</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE5E" flags="0x30">
    <title>Converter Model - Square Root of Converter Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Square-root lookup used for the capacity factor: each point holds the square root of its torque breakpoint (stock values are exact square roots, 0 to 20.9). Part of the torque converter model check: the PCM computes a converter capacity factor (engine speed over the square root of the torque going through the converter fluid, in rpm per square root of Nm), predicts the converter speed ratio from it and flags a mismatch when the measured speed ratio falls outside the band. Effect: changes the computed capacity factor (keep as square roots) Evidence: ledger:E0348, ledger:E1238, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>Nm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="25" />
      <LABEL index="2" value="50" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="100" />
      <LABEL index="5" value="125" />
      <LABEL index="6" value="150" />
      <LABEL index="7" value="175" />
      <LABEL index="8" value="200" />
      <LABEL index="9" value="225" />
      <LABEL index="10" value="250" />
      <LABEL index="11" value="275" />
      <LABEL index="12" value="300" />
      <LABEL index="13" value="325" />
      <LABEL index="14" value="350" />
      <LABEL index="15" value="375" />
      <LABEL index="16" value="400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EA1C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>sqrt(Nm)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>127.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE5F" flags="0x30">
    <title>Desired Shift Time Altitude Adder - Normal (1-2 / 2-3 / 3-4)</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time added to the desired upshift duration at altitude, by shift torque, set 0 (normal, cruise and 4-Lo shift modes on the stock calibration); scaled by the Desired Shift Time Altitude Weight table (1.0 at low barometric pressure, 0 at sea level on the stock calibration). Negative values shorten the target. Stock set 0: 0.05 s on the 2-3 upshift up to 400 Nm, 0 from 480 Nm and on the other upshifts. Which set each drive mode uses is chosen by Shift Set by Drive Mode. Effect: longer (positive) or shorter (negative) upshift target at a...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="55" />
      <LABEL index="4" value="110" />
      <LABEL index="5" value="165" />
      <LABEL index="6" value="220" />
      <LABEL index="7" value="275" />
      <LABEL index="8" value="330" />
      <LABEL index="9" value="385" />
      <LABEL index="10" value="440" />
      <LABEL index="11" value="495" />
      <LABEL index="12" value="550" />
      <LABEL index="13" value="605" />
      <LABEL index="14" value="660" />
      <LABEL index="15" value="715" />
      <LABEL index="16" value="770" />
      <LABEL index="17" value="825" />
      <LABEL index="18" value="880" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C0F6" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>-3.200000</min>
      <max>3.175000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE60" flags="0x30">
    <title>Desired Shift Time vs Torque - Normal (1-2 / 2-3 / 3-4)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target upshift duration the TAP adaption steers to, vs shift torque, normal modes (set 0); 0 = not adapted (3-4 stock) (E0235, E0237) Effect: adaptive shift duration target (shorter = firmer as TAP adds pressure) Evidence: ledger:E0235, ledger:E0237, ledger:E1295, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>MARKER/MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="MARKER" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="55" />
      <LABEL index="4" value="110" />
      <LABEL index="5" value="165" />
      <LABEL index="6" value="220" />
      <LABEL index="7" value="275" />
      <LABEL index="8" value="330" />
      <LABEL index="9" value="385" />
      <LABEL index="10" value="440" />
      <LABEL index="11" value="495" />
      <LABEL index="12" value="550" />
      <LABEL index="13" value="605" />
      <LABEL index="14" value="660" />
      <LABEL index="15" value="715" />
      <LABEL index="16" value="770" />
      <LABEL index="17" value="825" />
      <LABEL index="18" value="880" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C046" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE61" flags="0x30">
    <title>Downshift Base Pressure (Top Gear, Low Torque) - Torque Part</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shift torque part of the base pressure for downshifts from top gear with the torque state low, by shift torque (columns) and gear index (rows). The downshift base pressure is the sum of its turbine speed part and its shift torque part; the downshift pressure temperature modifier is added to it. &#x27;Top gear&#x27; means no upshift is available from the current gear: the highest gear the selected range allows, or a gear held by the cruise rule. 1 count = 4 kPa. Effect: raise = firmer downshift at that shift torque Evidence: ledger:E1...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="55" />
      <LABEL index="4" value="110" />
      <LABEL index="5" value="165" />
      <LABEL index="6" value="220" />
      <LABEL index="7" value="275" />
      <LABEL index="8" value="330" />
      <LABEL index="9" value="385" />
      <LABEL index="10" value="440" />
      <LABEL index="11" value="495" />
      <LABEL index="12" value="550" />
      <LABEL index="13" value="605" />
      <LABEL index="14" value="660" />
      <LABEL index="15" value="715" />
      <LABEL index="16" value="770" />
      <LABEL index="17" value="825" />
      <LABEL index="18" value="880" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>gear index</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A421" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>1020.000000</max>
      <MATH equation="X*4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE62" flags="0x30">
    <title>Torque Reduction vs Torque vs Shift (Normal / Performance / mode 2 x 1-2, 2-3, 3-4)</title>
    <description>Change in small steps and log. Each row is a 1-D byte curve [COUNT=0x11 (17 points)][TYPE (0 -&gt; output = point x256)][17 points]; COUNT and TYPE are structure bytes - never edit them (E0170). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque cut during an upshift, vs engine torque, per shift and shift mode. Formerly mis-identified as &#x27;Pedal Sensitivity&#x27; - it is shift torque management (E0198). Effect: more = softer, slower-feeling shifts; less = firmer shifts and more clutch load Evidence: ledger:E0170, ledger:E0198, ledger:E0215, ledger:E0243, ledger:E1295, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="55" />
      <LABEL index="4" value="110" />
      <LABEL index="5" value="165" />
      <LABEL index="6" value="220" />
      <LABEL index="7" value="275" />
      <LABEL index="8" value="330" />
      <LABEL index="9" value="385" />
      <LABEL index="10" value="440" />
      <LABEL index="11" value="495" />
      <LABEL index="12" value="550" />
      <LABEL index="13" value="605" />
      <LABEL index="14" value="660" />
      <LABEL index="15" value="715" />
      <LABEL index="16" value="770" />
      <LABEL index="17" value="825" />
      <LABEL index="18" value="880" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>mode x shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="Normal 1-2" />
      <LABEL index="1" value="Normal 2-3" />
      <LABEL index="2" value="Normal 3-4" />
      <LABEL index="3" value="Perf 1-2" />
      <LABEL index="4" value="Perf 2-3" />
      <LABEL index="5" value="Perf 3-4" />
      <LABEL index="6" value="Mode2 1-2" />
      <LABEL index="7" value="Mode2 2-3" />
      <LABEL index="8" value="Mode2 3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EFC4" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>99.609375</max>
      <MATH equation="X/2.56"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE63" flags="0x30">
    <title>Minimum Line Pressure vs Input Torque vs Output Speed - 1st Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Floor on the commanded line pressure, by transmission input torque (rows) and output speed (columns): the controller uses the larger of this value and its normal line pressure. Used while the controller&#x27;s gear index is 1st gear, in every range except range code 6. The row and column positions come from two breakpoint lists stored in the calibration; the labels show their stock values. Stock all 0 (no floor). Effect: raise = line pressure is never commanded below this at that torque and speed Evidence: ledger:E0359, ledger:E1171, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (output speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="50.001" />
      <LABEL index="2" value="100.002" />
      <LABEL index="3" value="600.009" />
      <LABEL index="4" value="1200.018" />
      <LABEL index="5" value="1500.023" />
      <LABEL index="6" value="1800.027" />
      <LABEL index="7" value="2100.032" />
      <LABEL index="8" value="2400.037" />
      <LABEL index="9" value="2700.041" />
      <LABEL index="10" value="3000.046" />
      <LABEL index="11" value="3300.05" />
      <LABEL index="12" value="3600.055" />
      <LABEL index="13" value="4750.072" />
      <LABEL index="14" value="5900.09" />
      <LABEL index="15" value="7050.108" />
      <LABEL index="16" value="8191.125" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>Nm (input torque)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="150.002" />
      <LABEL index="3" value="670.01" />
      <LABEL index="4" value="1000.015" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38227" mmedelementsizebits="8" mmedrowcount="5" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>1020.000000</max>
      <MATH equation="X*4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE64" flags="0x30">
    <title>Minimum Line Pressure vs Input Torque vs Output Speed - Range Code 6</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Floor on the commanded line pressure, by transmission input torque (rows) and output speed (columns): the controller uses the larger of this value and its normal line pressure. Used in transmission range code 6, where the result is also multiplied by a fluid temperature factor curve (all zero on stock) unless a controller flag bypasses that curve. The row and column positions come from two breakpoint lists stored in the calibration; the labels show their stock values. Stock all 0 (no floor). Effect: raise = line pressure is never commanded below this at that torque and speed Evidence: ledger:E0359, ledger:E1171, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (output speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="50.001" />
      <LABEL index="2" value="100.002" />
      <LABEL index="3" value="600.009" />
      <LABEL index="4" value="1200.018" />
      <LABEL index="5" value="1500.023" />
      <LABEL index="6" value="1800.027" />
      <LABEL index="7" value="2100.032" />
      <LABEL index="8" value="2400.037" />
      <LABEL index="9" value="2700.041" />
      <LABEL index="10" value="3000.046" />
      <LABEL index="11" value="3300.05" />
      <LABEL index="12" value="3600.055" />
      <LABEL index="13" value="4750.072" />
      <LABEL index="14" value="5900.09" />
      <LABEL index="15" value="7050.108" />
      <LABEL index="16" value="8191.125" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>Nm (input torque)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="150.002" />
      <LABEL index="3" value="670.01" />
      <LABEL index="4" value="1000.015" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38387" mmedelementsizebits="8" mmedrowcount="5" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>1020.000000</max>
      <MATH equation="X*4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE65" flags="0x30">
    <title>Accelerator Pedal Filter - Gain vs Pedal Gap, Rising</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain while the pedal is rising (pedal demand at or above the filtered pedal), by the gap between pedal demand and the filtered pedal. Above the hold gap the highest gain reached is kept until the gap shrinks or the direction changes. Stock 1.0 everywhere. Part of the accelerator pedal filter: the filtered pedal closes this share of its gap to the pedal demand every update; 1.0 follows the pedal at once. Effect: lower = the filtered pedal follows the pedal more slowly at that gap Evidence: ledger:E0330, ledger:E0593, ledger:E1190, ledger:E1722</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% (pedal gap)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.073" />
      <LABEL index="2" value="0.147" />
      <LABEL index="3" value="0.22" />
      <LABEL index="4" value="0.294" />
      <LABEL index="5" value="0.367" />
      <LABEL index="6" value="0.441" />
      <LABEL index="7" value="0.514" />
      <LABEL index="8" value="0.588" />
      <LABEL index="9" value="0.881" />
      <LABEL index="10" value="1.469" />
      <LABEL index="11" value="2.35" />
      <LABEL index="12" value="3.525" />
      <LABEL index="13" value="4.994" />
      <LABEL index="14" value="6.756" />
      <LABEL index="15" value="8.812" />
      <LABEL index="16" value="11.162" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24D78" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE66" flags="0x30">
    <title>Accelerator Pedal Filter - Gain vs Pedal Gap, Falling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain while the pedal is falling (pedal demand below the filtered pedal), by the gap between pedal demand and the filtered pedal. Above the hold gap the highest gain reached is kept until the gap shrinks or the direction changes. Stock 1.0 everywhere. Part of the accelerator pedal filter: the filtered pedal closes this share of its gap to the pedal demand every update; 1.0 follows the pedal at once. Effect: lower = the filtered pedal follows the pedal more slowly at that gap Evidence: ledger:E0330, ledger:E0593, ledger:E1190, ledger:E1722</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% (pedal gap)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.073" />
      <LABEL index="2" value="0.147" />
      <LABEL index="3" value="0.22" />
      <LABEL index="4" value="0.294" />
      <LABEL index="5" value="0.367" />
      <LABEL index="6" value="0.441" />
      <LABEL index="7" value="0.514" />
      <LABEL index="8" value="0.588" />
      <LABEL index="9" value="0.881" />
      <LABEL index="10" value="1.469" />
      <LABEL index="11" value="2.35" />
      <LABEL index="12" value="3.525" />
      <LABEL index="13" value="4.994" />
      <LABEL index="14" value="6.756" />
      <LABEL index="15" value="8.812" />
      <LABEL index="16" value="11.162" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24DC2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE67" flags="0x30">
    <title>Base Shift Pressure vs Torque - Normal (1-2 / 2-3 / 3-4)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 4L60-E commanded force-motor pressure during an upshift, vs shift torque, rows 1-2 / 2-3 / 3-4, normal modes (set 0). 1 count = 4 kPa = 0.58 psi; capped by max_line_pressure (621 kPa) (E0235, E0237) Effect: shift firmness (higher = firmer, shorter shifts) Evidence: ledger:E0235, ledger:E0237, ledger:E1295, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>MARKER/MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="MARKER" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="55" />
      <LABEL index="4" value="110" />
      <LABEL index="5" value="165" />
      <LABEL index="6" value="220" />
      <LABEL index="7" value="275" />
      <LABEL index="8" value="330" />
      <LABEL index="9" value="385" />
      <LABEL index="10" value="440" />
      <LABEL index="11" value="495" />
      <LABEL index="12" value="550" />
      <LABEL index="13" value="605" />
      <LABEL index="14" value="660" />
      <LABEL index="15" value="715" />
      <LABEL index="16" value="770" />
      <LABEL index="17" value="825" />
      <LABEL index="18" value="880" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A256" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>psi</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>147.938454</max>
      <MATH equation="X*0.5801508"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE68" flags="0x30">
    <title>Shift Torque Reduction Profile - End Time</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE=6][17 points]; COUNT and TYPE are structure bytes, never edit them (E0365). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time at which the reduction has ramped fully out, by gear (stock 0.60 / 0.55 / 0.50 s). Part of the shift torque-reduction profile: ramp in with the measured ratio, hold for the hold time, ramp out by the end time. On the stock H3 the reduction target is zero, so the profile does nothing until that is set. Effect: shift torque reduction timing Evidence: ledger:E0365, ledger:E0706, ledger:E1295, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="55" />
      <LABEL index="4" value="110" />
      <LABEL index="5" value="165" />
      <LABEL index="6" value="220" />
      <LABEL index="7" value="275" />
      <LABEL index="8" value="330" />
      <LABEL index="9" value="385" />
      <LABEL index="10" value="440" />
      <LABEL index="11" value="495" />
      <LABEL index="12" value="550" />
      <LABEL index="13" value="605" />
      <LABEL index="14" value="660" />
      <LABEL index="15" value="715" />
      <LABEL index="16" value="770" />
      <LABEL index="17" value="825" />
      <LABEL index="18" value="880" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>current gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EF85" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE69" flags="0x30">
    <title>Shift Torque Reduction Profile - Hold Time</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE=6][17 points]; COUNT and TYPE are structure bytes, never edit them (E0365). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long full reduction is held after the ratio change, by gear (stock 0.40 / 0.35 / 0.30 s). Part of the shift torque-reduction profile: ramp in with the measured ratio, hold for the hold time, ramp out by the end time. On the stock H3 the reduction target is zero, so the profile does nothing until that is set. Effect: shift torque reduction timing Evidence: ledger:E0365, ledger:E0706, ledger:E1295, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="55" />
      <LABEL index="4" value="110" />
      <LABEL index="5" value="165" />
      <LABEL index="6" value="220" />
      <LABEL index="7" value="275" />
      <LABEL index="8" value="330" />
      <LABEL index="9" value="385" />
      <LABEL index="10" value="440" />
      <LABEL index="11" value="495" />
      <LABEL index="12" value="550" />
      <LABEL index="13" value="605" />
      <LABEL index="14" value="660" />
      <LABEL index="15" value="715" />
      <LABEL index="16" value="770" />
      <LABEL index="17" value="825" />
      <LABEL index="18" value="880" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>current gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3EF4C" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6.375000</max>
      <MATH equation="X/40"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE6A" flags="0x30">
    <title>Shift Adapt - Delay Step Gain vs Shift Torque</title>
    <description>Change in small steps and log. Each row is [COUNT][TYPE][points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier on the shift delay step, by shift torque (columns) for each upshift (rows). Stock 0.25 at no torque rising to 1.0 from 240 Nm for 1-2 and 2-3, 0 for 3-4. Part of the adaptive shift pressure learning (TAP), which corrects the learned shift pressure after each upshift. Effect: raise = larger delay correction at that shift torque Evidence: ledger:E0806, ledger:E1029, ledger:E1318, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="55" />
      <LABEL index="4" value="110" />
      <LABEL index="5" value="165" />
      <LABEL index="6" value="220" />
      <LABEL index="7" value="275" />
      <LABEL index="8" value="330" />
      <LABEL index="9" value="385" />
      <LABEL index="10" value="440" />
      <LABEL index="11" value="495" />
      <LABEL index="12" value="550" />
      <LABEL index="13" value="605" />
      <LABEL index="14" value="660" />
      <LABEL index="15" value="715" />
      <LABEL index="16" value="770" />
      <LABEL index="17" value="825" />
      <LABEL index="18" value="880" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3C53E" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE6B" flags="0x30">
    <title>Shift Torque Reduction - Fade End (gear ratio)</title>
    <description>Change in small steps and log. Each row is a 1-D curve [COUNT = 17][17 points]; COUNT is a structure word, never edit it (E0340). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During an upshift the measured gear ratio falls from the old gear to the new one. This sets the ratio at which the reduction has faded out completely, by engine torque, for each shift (rows 1-2, 2-3, 3-4). Stock 1-2 row 1.75 to 2.44. Works with Torque Reduction vs Torque vs Shift (E0340). Effect: when during the shift engine torque is pulled and restored Evidence: ledger:E0340, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="55" />
      <LABEL index="3" value="110" />
      <LABEL index="4" value="165" />
      <LABEL index="5" value="220" />
      <LABEL index="6" value="275" />
      <LABEL index="7" value="330" />
      <LABEL index="8" value="385" />
      <LABEL index="9" value="440" />
      <LABEL index="10" value="495" />
      <LABEL index="11" value="550" />
      <LABEL index="12" value="605" />
      <LABEL index="13" value="660" />
      <LABEL index="14" value="715" />
      <LABEL index="15" value="770" />
      <LABEL index="16" value="825" />
      <LABEL index="17" value="880" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F1C4" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gear ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE6C" flags="0x30">
    <title>Shift Torque Reduction - Fade Start (gear ratio)</title>
    <description>Change in small steps and log. Each row is a 1-D curve [COUNT = 17][17 points]; COUNT is a structure word, never edit it (E0340). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During an upshift the measured gear ratio falls from the old gear to the new one. This sets the ratio at which the reduction starts fading out, by engine torque, for each shift (rows 1-2, 2-3, 3-4). Stock 1-2 row 2.00 to 2.50. Works with Torque Reduction vs Torque vs Shift (E0340). Effect: when during the shift engine torque is pulled and restored Evidence: ledger:E0340, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="55" />
      <LABEL index="3" value="110" />
      <LABEL index="4" value="165" />
      <LABEL index="5" value="220" />
      <LABEL index="6" value="275" />
      <LABEL index="7" value="330" />
      <LABEL index="8" value="385" />
      <LABEL index="9" value="440" />
      <LABEL index="10" value="495" />
      <LABEL index="11" value="550" />
      <LABEL index="12" value="605" />
      <LABEL index="13" value="660" />
      <LABEL index="14" value="715" />
      <LABEL index="15" value="770" />
      <LABEL index="16" value="825" />
      <LABEL index="17" value="880" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F154" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gear ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE6D" flags="0x30">
    <title>Shift Torque Reduction - Full Reduction At (gear ratio)</title>
    <description>Change in small steps and log. Each row is a 1-D curve [COUNT = 17][17 points]; COUNT is a structure word, never edit it (E0340). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During an upshift the measured gear ratio falls from the old gear to the new one. This sets the ratio at which the reduction reaches its full value, by engine torque, for each shift (rows 1-2, 2-3, 3-4). Stock 1-2 row 2.88 flat. Works with Torque Reduction vs Torque vs Shift (E0340). Effect: when during the shift engine torque is pulled and restored Evidence: ledger:E0340, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="55" />
      <LABEL index="3" value="110" />
      <LABEL index="4" value="165" />
      <LABEL index="5" value="220" />
      <LABEL index="6" value="275" />
      <LABEL index="7" value="330" />
      <LABEL index="8" value="385" />
      <LABEL index="9" value="440" />
      <LABEL index="10" value="495" />
      <LABEL index="11" value="550" />
      <LABEL index="12" value="605" />
      <LABEL index="13" value="660" />
      <LABEL index="14" value="715" />
      <LABEL index="15" value="770" />
      <LABEL index="16" value="825" />
      <LABEL index="17" value="880" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F0E4" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gear ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE6E" flags="0x30">
    <title>Shift Torque Reduction - Ramp-In Start (gear ratio)</title>
    <description>Change in small steps and log. Each row is a 1-D curve [COUNT = 17][17 points]; COUNT is a structure word, never edit it (E0340). Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During an upshift the measured gear ratio falls from the old gear to the new one. This sets the ratio at which the reduction starts ramping in, by engine torque, for each shift (rows 1-2, 2-3, 3-4). Stock 1-2 row 2.88 flat. Works with Torque Reduction vs Torque vs Shift (E0340). Effect: when during the shift engine torque is pulled and restored Evidence: ledger:E0340, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="55" />
      <LABEL index="3" value="110" />
      <LABEL index="4" value="165" />
      <LABEL index="5" value="220" />
      <LABEL index="6" value="275" />
      <LABEL index="7" value="330" />
      <LABEL index="8" value="385" />
      <LABEL index="9" value="440" />
      <LABEL index="10" value="495" />
      <LABEL index="11" value="550" />
      <LABEL index="12" value="605" />
      <LABEL index="13" value="660" />
      <LABEL index="14" value="715" />
      <LABEL index="15" value="770" />
      <LABEL index="16" value="825" />
      <LABEL index="17" value="880" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3F074" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gear ratio</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE6F" flags="0x30">
    <title>Upshift Pressure Temp Modifier - 1-2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pressure added to the 1-2 shift pressure vs trans temp and shift torque (E0235, E0237) Effect: temperature correction of shift pressure Evidence: ledger:E0235, ledger:E0237, ledger:E1288, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (trans temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>shift torque (lb-ft; stored Nm x4)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="162.25" />
      <LABEL index="2" value="324.5" />
      <LABEL index="3" value="486.75" />
      <LABEL index="4" value="649" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3AEEA" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>psi</units>
      <decimalpl>3</decimalpl>
      <min>-297.032090</min>
      <max>297.023025</max>
      <MATH equation="X*0.0090647"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE70" flags="0x30">
    <title>Upshift Base Pressure (Top Gear, Low Torque) vs Torque</title>
    <description>Change in small steps and log. Each row is [COUNT=17][TYPE][17 points]; COUNT and TYPE are structure bytes, never edit them. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base pressure commanded during an upshift when the top gear flag is set and the torque state is low, instead of the normal base shift pressure table, by shift torque (columns) and upshift (rows). &#x27;Top gear&#x27; means no upshift is available from the current gear: the highest gear the selected range allows, or a gear held by the cruise rule. 1 count = 4 kPa. Effect: raise = firmer upshift in that state Evidence: ledger:E1030, ledger:E1170, ledger:E1317, ledger:E1722</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>COUNT/TYPE + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="TYPE" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="55" />
      <LABEL index="4" value="110" />
      <LABEL index="5" value="165" />
      <LABEL index="6" value="220" />
      <LABEL index="7" value="275" />
      <LABEL index="8" value="330" />
      <LABEL index="9" value="385" />
      <LABEL index="10" value="440" />
      <LABEL index="11" value="495" />
      <LABEL index="12" value="550" />
      <LABEL index="13" value="605" />
      <LABEL index="14" value="660" />
      <LABEL index="15" value="715" />
      <LABEL index="16" value="770" />
      <LABEL index="17" value="825" />
      <LABEL index="18" value="880" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>shift</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1-2" />
      <LABEL index="1" value="2-3" />
      <LABEL index="2" value="3-4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3A33A" mmedelementsizebits="8" mmedrowcount="3" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>1020.000000</max>
      <MATH equation="X*4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE71" flags="0x0">
    <title>Swap - Theft Deterrent (VATS) Code P1630 Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Swap setting. 1 (stock): the PCM runs its P1630 theft deterrent check and sets code P1630 when the theft deterrent status is not correct. 0: the check never runs, so P1630 is never set and never reported as passed. Use it on an engine swap with the theft deterrent fuel enable bypassed, so the swapped PCM is not left with P1630 from the missing body control module. P1630 is a non-emissions code that does not light the check engine lamp. No password or security data is read or changed. For use on your own engine swap only. Effect: 0 = P1630 check off (never set); 1 = stock Evidence: ledger:E0658, ledger:E1695, ledger:E1701</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2095E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on (stock), 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE72" flags="0x0">
    <title>Swap - Theft Deterrent (VATS) Code P1631 Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Swap setting. 1 (stock): the PCM runs its P1631 theft deterrent check and sets code P1631 when the theft deterrent status is not correct. 0: the check never runs, so P1631 is never set and never reported as passed. Use it on an engine swap with the theft deterrent fuel enable bypassed, so the swapped PCM is not left with P1631 from the missing body control module. P1631 is a non-emissions code that does not light the check engine lamp. No password or security data is read or changed. For use on your own engine swap only. Effect: 0 = P1631 check off (never set); 1 = stock Evidence: ledger:E0659, ledger:E1695, ledger:E1701</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20960" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on (stock), 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE73" flags="0x30">
    <title>DTC Type and MIL per Code</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. One byte per trouble code (row labels), as in the 0411 DTC processing and MIL tables. The low two bits set the code&#x27;s type: 0 = not reported (the PCM never stores it); 1 = type A, stored on the first failure; 2 = type B, stored when the check fails on two trips in a row; 3 = type C, stored on the first failure and never lights the lamp. Add 4 to request the check engine lamp when the code is stored (types A and B only). Examples: 5 = type A with lamp, 6 = type B with lamp, 3 = stored without lamp, 0 = off. Types 0 and 3 also drop the code from its monitor&#x27;s readiness check: a monitor reports complete once all o...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>284</indexcount>
      <units>code</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="P0000" />
      <LABEL index="1" value="P0011" />
      <LABEL index="2" value="P0013" />
      <LABEL index="3" value="P0014" />
      <LABEL index="4" value="P0016" />
      <LABEL index="5" value="P0017" />
      <LABEL index="6" value="P0018" />
      <LABEL index="7" value="P0019" />
      <LABEL index="8" value="P0030" />
      <LABEL index="9" value="P0036" />
      <LABEL index="10" value="P0050" />
      <LABEL index="11" value="P0056" />
      <LABEL index="12" value="P0101" />
      <LABEL index="13" value="P0102" />
      <LABEL index="14" value="P0103" />
      <LABEL index="15" value="P0106" />
      <LABEL index="16" value="P0107" />
      <LABEL index="17" value="P0108" />
      <LABEL index="18" value="P0112" />
      <LABEL index="19" value="P0113" />
      <LABEL index="20" value="P0116" />
      <LABEL index="21" value="P0117" />
      <LABEL index="22" value="P0118" />
      <LABEL index="23" value="P0121" />
      <LABEL index="24" value="P0122" />
      <LABEL index="25" value="P0123" />
      <LABEL index="26" value="P0125" />
      <LABEL index="27" value="P0128" />
      <LABEL index="28" value="P0130" />
      <LABEL index="29" value="P0131" />
      <LABEL index="30" value="P0132" />
      <LABEL index="31" value="P0133" />
      <LABEL index="32" value="P0134" />
      <LABEL index="33" value="P0135" />
      <LABEL index="34" value="P0136" />
      <LABEL index="35" value="P0137" />
      <LABEL index="36" value="P0138" />
      <LABEL index="37" value="P0140" />
      <LABEL index="38" value="P0141" />
      <LABEL index="39" value="P0142" />
      <LABEL index="40" value="P0150" />
      <LABEL index="41" value="P0151" />
      <LABEL index="42" value="P0152" />
      <LABEL index="43" value="P0153" />
      <LABEL index="44" value="P0154" />
      <LABEL index="45" value="P0155" />
      <LABEL index="46" value="P0156" />
      <LABEL index="47" value="P0157" />
      <LABEL index="48" value="P0158" />
      <LABEL index="49" value="P0160" />
      <LABEL index="50" value="P0161" />
      <LABEL index="51" value="P0171" />
      <LABEL index="52" value="P0172" />
      <LABEL index="53" value="P0174" />
      <LABEL index="54" value="P0175" />
      <LABEL index="55" value="P0201" />
      <LABEL index="56" value="P0202" />
      <LABEL index="57" value="P0203" />
      <LABEL index="58" value="P0204" />
      <LABEL index="59" value="P0205" />
      <LABEL index="60" value="P0206" />
      <LABEL index="61" value="P0207" />
      <LABEL index="62" value="P0208" />
      <LABEL index="63" value="P0218" />
      <LABEL index="64" value="P0222" />
      <LABEL index="65" value="P0223" />
      <LABEL index="66" value="P0230" />
      <LABEL index="67" value="P0300" />
      <LABEL index="68" value="P0325" />
      <LABEL index="69" value="P0326" />
      <LABEL index="70" value="P0327" />
      <LABEL index="71" value="P0332" />
      <LABEL index="72" value="P0335" />
      <LABEL index="73" value="P0336" />
      <LABEL index="74" value="P0340" />
      <LABEL index="75" value="P0341" />
      <LABEL index="76" value="P0345" />
      <LABEL index="77" value="P0346" />
      <LABEL index="78" value="P0351" />
      <LABEL index="79" value="P0352" />
      <LABEL index="80" value="P0353" />
      <LABEL index="81" value="P0354" />
      <LABEL index="82" value="P0355" />
      <LABEL index="83" value="P0356" />
      <LABEL index="84" value="P0357" />
      <LABEL index="85" value="P0358" />
      <LABEL index="86" value="P0365" />
      <LABEL index="87" value="P0366" />
      <LABEL index="88" value="P0385" />
      <LABEL index="89" value="P0386" />
      <LABEL index="90" value="P0390" />
      <LABEL index="91" value="P0391" />
      <LABEL index="92" value="P0410" />
      <LABEL index="93" value="P0411" />
      <LABEL index="94" value="P0412" />
      <LABEL index="95" value="P0418" />
      <LABEL index="96" value="P0420" />
      <LABEL index="97" value="P0430" />
      <LABEL index="98" value="P0455" />
      <LABEL index="99" value="P0442" />
      <LABEL index="100" value="P0443" />
      <LABEL index="101" value="P0446" />
      <LABEL index="102" value="P0449" />
      <LABEL index="103" value="P0451" />
      <LABEL index="104" value="P0452" />
      <LABEL index="105" value="P0453" />
      <LABEL index="106" value="P0454" />
      <LABEL index="107" value="P0461" />
      <LABEL index="108" value="P0462" />
      <LABEL index="109" value="P0463" />
      <LABEL index="110" value="P0464" />
      <LABEL index="111" value="P0480" />
      <LABEL index="112" value="P0481" />
      <LABEL index="113" value="P0482" />
      <LABEL index="114" value="P0483" />
      <LABEL index="115" value="P0493" />
      <LABEL index="116" value="P0495" />
      <LABEL index="117" value="P0502" />
      <LABEL index="118" value="P0503" />
      <LABEL index="119" value="P0506" />
      <LABEL index="120" value="P0507" />
      <LABEL index="121" value="P0512" />
      <LABEL index="122" value="P0522" />
      <LABEL index="123" value="P0523" />
      <LABEL index="124" value="P0526" />
      <LABEL index="125" value="P0532" />
      <LABEL index="126" value="P0533" />
      <LABEL index="127" value="P0562" />
      <LABEL index="128" value="P0563" />
      <LABEL index="129" value="P0564" />
      <LABEL index="130" value="P0567" />
      <LABEL index="131" value="P0568" />
      <LABEL index="132" value="P0572" />
      <LABEL index="133" value="P0573" />
      <LABEL index="134" value="P0601" />
      <LABEL index="135" value="P0602" />
      <LABEL index="136" value="P0603" />
      <LABEL index="137" value="P0604" />
      <LABEL index="138" value="P0606" />
      <LABEL index="139" value="P0607" />
      <LABEL index="140" value="P0615" />
      <LABEL index="141" value="P0621" />
      <LABEL index="142" value="P0622" />
      <LABEL index="143" value="P0650" />
      <LABEL index="144" value="P0700" />
      <LABEL index="145" value="P0703" />
      <LABEL index="146" value="P0833" />
      <LABEL index="147" value="P0705" />
      <LABEL index="148" value="P0711" />
      <LABEL index="149" value="P0712" />
      <LABEL index="150" value="P0713" />
      <LABEL index="151" value="P0716" />
      <LABEL index="152" value="P0717" />
      <LABEL index="153" value="P0719" />
      <LABEL index="154" value="P0722" />
      <LABEL index="155" value="P0723" />
      <LABEL index="156" value="P0724" />
      <LABEL index="157" value="P0731" />
      <LABEL index="158" value="P0732" />
      <LABEL index="159" value="P0733" />
      <LABEL index="160" value="P0734" />
      <LABEL index="161" value="P0735" />
      <LABEL index="162" value="P0741" />
      <LABEL index="163" value="P0742" />
      <LABEL index="164" value="P0748" />
      <LABEL index="165" value="P0751" />
      <LABEL index="166" value="P0752" />
      <LABEL index="167" value="P0756" />
      <LABEL index="168" value="P0757" />
      <LABEL index="169" value="P0761" />
      <LABEL index="170" value="P0762" />
      <LABEL index="171" value="P0787" />
      <LABEL index="172" value="P0788" />
      <LABEL index="173" value="P1101" />
      <LABEL index="174" value="P1106" />
      <LABEL index="175" value="P1107" />
      <LABEL index="176" value="P1111" />
      <LABEL index="177" value="P1112" />
      <LABEL index="178" value="P1114" />
      <LABEL index="179" value="P1115" />
      <LABEL index="180" value="P0120" />
      <LABEL index="181" value="P1133" />
      <LABEL index="182" value="P1134" />
      <LABEL index="183" value="P1153" />
      <LABEL index="184" value="P1154" />
      <LABEL index="185" value="P0520" />
      <LABEL index="186" value="P0220" />
      <LABEL index="187" value="P2135" />
      <LABEL index="188" value="P2138" />
      <LABEL index="189" value="P2120" />
      <LABEL index="190" value="P2125" />
      <LABEL index="191" value="P0315" />
      <LABEL index="192" value="P1372" />
      <LABEL index="193" value="P1380" />
      <LABEL index="194" value="P1381" />
      <LABEL index="195" value="P1400" />
      <LABEL index="196" value="P0491" />
      <LABEL index="197" value="P0492" />
      <LABEL index="198" value="P2066" />
      <LABEL index="199" value="P2067" />
      <LABEL index="200" value="P2068" />
      <LABEL index="201" value="P0496" />
      <LABEL index="202" value="P1482" />
      <LABEL index="203" value="P2176" />
      <LABEL index="204" value="P0068" />
      <LABEL index="205" value="P2101" />
      <LABEL index="206" value="P1516" />
      <LABEL index="207" value="P2119" />
      <LABEL index="208" value="P1545" />
      <LABEL index="209" value="P0856" />
      <LABEL index="210" value="P1574" />
      <LABEL index="211" value="P1575" />
      <LABEL index="212" value="P250A" />
      <LABEL index="213" value="P062F" />
      <LABEL index="214" value="P1630" />
      <LABEL index="215" value="P1631" />
      <LABEL index="216" value="P1633" />
      <LABEL index="217" value="P1634" />
      <LABEL index="218" value="P0641" />
      <LABEL index="219" value="P0651" />
      <LABEL index="220" value="P060D" />
      <LABEL index="221" value="P060E" />
      <LABEL index="222" value="P1682" />
      <LABEL index="223" value="P2610" />
      <LABEL index="224" value="P1689" />
      <LABEL index="225" value="P1700" />
      <LABEL index="226" value="P1750" />
      <LABEL index="227" value="P2544" />
      <LABEL index="228" value="P278A" />
      <LABEL index="229" value="P1810" />
      <LABEL index="230" value="P1811" />
      <LABEL index="231" value="P1814" />
      <LABEL index="232" value="P1815" />
      <LABEL index="233" value="P1816" />
      <LABEL index="234" value="P1817" />
      <LABEL index="235" value="P1818" />
      <LABEL index="236" value="P1819" />
      <LABEL index="237" value="P1820" />
      <LABEL index="238" value="P1822" />
      <LABEL index="239" value="P1823" />
      <LABEL index="240" value="P1825" />
      <LABEL index="241" value="P1826" />
      <LABEL index="242" value="P0973" />
      <LABEL index="243" value="P0974" />
      <LABEL index="244" value="P0976" />
      <LABEL index="245" value="P0977" />
      <LABEL index="246" value="P2769" />
      <LABEL index="247" value="P2770" />
      <LABEL index="248" value="P0979" />
      <LABEL index="249" value="P0980" />
      <LABEL index="250" value="P2764" />
      <LABEL index="251" value="P2763" />
      <LABEL index="252" value="P0897" />
      <LABEL index="253" value="P0894" />
      <LABEL index="254" value="P2771" />
      <LABEL index="255" value="P1887" />
      <LABEL index="256" value="P2025" />
      <LABEL index="257" value="P2026" />
      <LABEL index="258" value="P2027" />
      <LABEL index="259" value="P2122" />
      <LABEL index="260" value="P2123" />
      <LABEL index="261" value="P2127" />
      <LABEL index="262" value="P2128" />
      <LABEL index="263" value="P2430" />
      <LABEL index="264" value="P2431" />
      <LABEL index="265" value="P2432" />
      <LABEL index="266" value="P2433" />
      <LABEL index="267" value="P2435" />
      <LABEL index="268" value="P2436" />
      <LABEL index="269" value="P2437" />
      <LABEL index="270" value="P2438" />
      <LABEL index="271" value="P2440" />
      <LABEL index="272" value="P2444" />
      <LABEL index="273" value="U1040" />
      <LABEL index="274" value="U1056" />
      <LABEL index="275" value="U1064" />
      <LABEL index="276" value="U1065" />
      <LABEL index="277" value="U1066" />
      <LABEL index="278" value="U1088" />
      <LABEL index="279" value="U1096" />
      <LABEL index="280" value="U1152" />
      <LABEL index="281" value="U1192" />
      <LABEL index="282" value="U1300" />
      <LABEL index="283" value="U1301" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x33334" mmedelementsizebits="8" mmedrowcount="284" mmedcolcount="1" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>0 off, 1 A, 2 B, 3 C, add 4 for MIL</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE74" flags="0x0">
    <title>Trans Fluid Temp Sensor Circuit Low Check Enable (P0712)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the transmission fluid temperature sensor circuit low check on or off. 1: the PCM runs the check and can set P0712. 0: the check never runs, so P0712 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0712 check off (never set); 1 = check on Evidence: ledger:E1725, ledger:E1732</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F79A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE75" flags="0x0">
    <title>TFP Switch Circuit Check Enable (P1810)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the TFP valve position switch / 4WD low indicator circuit check on or off. 1: the PCM runs the check and can set P1810. 0: the check never runs, so P1810 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P1810 check off (never set); 1 = check on Evidence: ledger:E1725, ledger:E1732</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3F856" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE76" flags="0x0">
    <title>Cam Sensor Fault Start - Running Time to Stand Down</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cranking strategy for a failed cam sensor: how long the engine must stay above the running engine speed before the strategy stands down for this start. Stock 0.6 s. Effect: raise = the strategy stays ready longer after the engine starts Evidence: ledger:E0324, ledger:E1274, ledger:E1275, ledger:E1756</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x23ADE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE77" flags="0x0">
    <title>Cam Sensor Fault Start - Minimum Crank Time Before Fallback</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cranking strategy for a failed cam sensor: with a cam sensor fault set, the crank / cam position decoding switches to its fallback mode once the crank time reaches this. Stock 0 s (switches at once). Effect: raise = the PCM cranks longer in its normal mode before switching to the fallback mode Evidence: ledger:E0324, ledger:E1274, ledger:E1275, ledger:E1756</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x23AE0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE78" flags="0x0">
    <title>Purge in Open Loop - Run Time Delay, Cold Start (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine run time before purge may start in open loop after a start below the coolant split. Stock 0 s. Part of an optional path that lets canister purge start while fuel control is still in open loop, after a run time delay chosen by start-up coolant temperature. This open loop purge path is switched off in the stock calibration, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = purge waits longer after a cold start) Evidence: ledger:E1642, ledger:E1756</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25320" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE79" flags="0x0">
    <title>Purge in Open Loop - Run Time Delay, Warm Start (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine run time before purge may start in open loop after a start at or above the coolant split. Stock 0 s. Part of an optional path that lets canister purge start while fuel control is still in open loop, after a run time delay chosen by start-up coolant temperature. This open loop purge path is switched off in the stock calibration, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = purge waits longer after a warm start) Evidence: ledger:E1642, ledger:E1756</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25322" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE7A" flags="0x0">
    <title>Purge in Open Loop - Start-Up Coolant Split (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up coolant temperature that picks the cold delay (below) or the warm delay (at or above). Stock 72 C. Part of an optional path that lets canister purge start while fuel control is still in open loop, after a run time delay chosen by start-up coolant temperature. This open loop purge path is switched off in the stock calibration, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1642, ledger:E1756</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x25326" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE7B" flags="0x0">
    <title>Traction Control Gear Request - Cold Engine Torque Limit (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With the engine at or below the traction control cold engine coolant temperature and the traction control torque limit below this (stock 300 Nm), the gear request uses its first set of conditions, the low throttle threshold and the long arming time; otherwise it uses the other two condition sets, the high throttle threshold and the short arming time. Part of the traction control gear request, which is switched off on this calibration and is not applied to the shift schedule, so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0504, ledger:E0918, ledger:E0925, ledger:E1114, ledger:E1440, ledger:E1756</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30338" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>16383.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE7C" flags="0x0">
    <title>Traction Control Gear Request - Torque Limit Threshold A (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the traction control torque limit is below this (with vehicle speed and rpm above their thresholds), traction control requests a gear change. On this calibration the request is not applied to the shift schedule. Stock 80 Nm. Effect: no effect on the stock calibration (the gear request is not applied) Evidence: ledger:E0502, ledger:E0914, ledger:E0918, ledger:E0925, ledger:E1114, ledger:E1756</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30360" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE7D" flags="0x0">
    <title>Traction Control Gear Request - Speed Threshold A (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First request condition: vehicle speed must be above this (stock 22 km/h), with the torque limit below threshold A and engine speed above its threshold. On this calibration the request is not applied to the shift schedule (inactive). Effect: no effect on this truck Evidence: ledger:E0502, ledger:E0717, ledger:E0733, ledger:E0918, ledger:E0925, ledger:E1377, ledger:E1756</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30362" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE7E" flags="0x0">
    <title>Catalyst Monitor - Purge Factor Limit (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): the test only becomes ready once the purge factor has been ramped down to this share of full purge or lower. Stock 100 %: always met, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (lower = the catalyst test waits for purge to be ramped further down) Evidence: ledger:E0468, ledger:E1458, ledger:E1756</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3290A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE7F" flags="0x0">
    <title>P0014 Check - Desired Cam Steady Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam position check P0014: how long the desired cam angle must stay inside the steady band before samples are taken. Stock 3 s. Effect: raise = the desired cam angle must be steady longer before the check samples Evidence: ledger:E1057, ledger:E1756</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x33472" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE80" flags="0x0">
    <title>MAP Plausibility - Fail Count (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: the check&#x27;s enable is off, so it never runs. MAP plausibility check: every sample in which manifold pressure is above the high limit or below the low limit for the current engine speed and throttle area counts as out of band. When the out-of-band count reaches the fail count, the window ends as a failure; when the window reaches its sample count first, it ends as a pass. The high limit tops out near 104 kPa, so sustained boost would be counted out of band, but the check sets no code. This is the out-of-band sample count that ends a window as a failure. Stock 80. Effect: raise = more out...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36818" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE81" flags="0x0">
    <title>MAP Plausibility - Window Samples (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: the check&#x27;s enable is off, so it never runs. MAP plausibility check: every sample in which manifold pressure is above the high limit or below the low limit for the current engine speed and throttle area counts as out of band. When the out-of-band count reaches the fail count, the window ends as a failure; when the window reaches its sample count first, it ends as a pass. The high limit tops out near 104 kPa, so sustained boost would be counted out of band, but the check sets no code. This is the number of samples in a window. Stock 100. Effect: raise = longer windows (keep above the fai...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3681A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE82" flags="0x0">
    <title>TCC Release - Negative Slip in Upshift, On Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During an upshift, converter slip below this value turns the negative slip release on (stock -4096 rpm: never). The converter clutch is released while it is on. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = release the clutch on negative slip during upshifts) Evidence: ledger:E1303, ledger:E1756</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D230" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE83" flags="0x0">
    <title>TCC Release - Negative Slip in Upshift, Off Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During an upshift, converter slip above this value turns the negative slip release off (stock 50 rpm). This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1303, ledger:E1756</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D232" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE84" flags="0x0">
    <title>TCC Slip Target - Floor After Event</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum TCC slip target while the A/C compressor runs and for the hold time after it turns off. Stock 20 rpm. Effect: TCC lock-up slip Evidence: ledger:E0370, ledger:E0702, ledger:E1385, ledger:E1756</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x3D4A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE85" flags="0x0">
    <title>Garage Shift Fill Strategy - Final Step Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the optional fill-phase strategy for garage shifts (engaging Drive or Reverse from Park or Neutral). Time the final step holds the final pressure before the strategy ends. Stock 0. Dormant: the strategy is switched off in this calibration (its enable is 0), so it has no effect on this truck&#x27;s software. Effect: raise = the final pressure is held longer Evidence: ledger:E1168, ledger:E1237, ledger:E1901</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x381BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE86" flags="0x0">
    <title>Garage Shift Fill Phase 1 - Maximum Time, Into Drive</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12627882), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the optional fill-phase strategy for garage shifts (engaging Drive or Reverse from Park or Neutral). The first phase ends after this time from the start of the engagement, if it has not ended already. Stock 0. Dormant: the strategy is switched off in this calibration (its enable is 0), so it has no effect on this truck&#x27;s software. Effect: raise = longer first phase allowed Evidence: ledger:E1168, ledger:E1237, ledger:E1901</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x381BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
</XDFFORMAT>