<?xml version="1.0" encoding="utf-8"?>
<XDFFORMAT version="1.60">
  <XDFHEADER>
    <flags>0x1</flags>
    <deftitle>P12 Suite - P12 OS 12610624 (catalog draft) - CATALOG DRAFT</deftitle>
    <description>OS ID 12610624 ONLY. P12 Suite catalog draft: every item was located and checked in this OS&#x27;s code (the routine that reads it is the same code as in the P12 Suite H3 definition, OS 12627884, and its table header, lookup and values were checked); not confirmed on a vehicle. Descriptions and quoted stock values describe the H3. Big-endian. Table axes are computed by the code, so axis labels are fixed values, not bin data. NO CHECKSUM is defined on purpose: after saving, correct the P12 segment checksums (python h3suite/run.py p12 repair &lt;bin&gt;, or a flashing tool that corrects P12 segments) before any flash. Edit in small steps and log.</description>
    <BASEOFFSET offset="0" subtract="0" />
    <DEFAULTS datasizeinbits="16" sigdigits="2" outputtype="1" signed="0" lsbfirst="0" float="0" />
    <REGION type="0xFFFFFFFF" startaddress="0x0" size="0x100000" regionflags="0x0" name="Bin" desc="P12 image" />
    <CATEGORY index="0x0" name="Spark" />
    <CATEGORY index="0x1" name="Fuel" />
    <CATEGORY index="0x2" name="Airflow" />
    <CATEGORY index="0x3" name="Limits" />
    <CATEGORY index="0x4" name="Idle" />
    <CATEGORY index="0x5" name="Diagnostics" />
    <CATEGORY index="0x6" name="Engine" />
    <CATEGORY index="0x7" name="Torque" />
    <CATEGORY index="0x8" name="Speedometer" />
    <CATEGORY index="0x9" name="Transmission" />
    <CATEGORY index="0xA" name="Throttle" />
    <CATEGORY index="0xB" name="Sensors" />
    <CATEGORY index="0xC" name="Segment Info" />
    <CATEGORY index="0xD" name="DO NOT TUNE" />
  </XDFHEADER>
  <XDFTABLE uniqueid="0x0" flags="0x30">
    <title>Main Spark Advance - High Octane</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base spark advance vs cylinder airmass x RPM, high-octane table. The PCM runs High minus (High - Low) x the learned octane scaler: scaler 0 = pure High, 1.0 = pure Low. After a reset or fault the scaler starts at 1.0 (all Low) and octane learn moves it toward High while there is no knock (E0296). Effect: increase = more timing &amp; torque (and more knock risk) Evidence: ledger:E0002, ledger:E0003, ledger:E0004, ledger:E0006, ledger:E0069, ledger:E0071, ledger:E0175, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E0296, ledger:E1297, ledger:E1338</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2D56D" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1" flags="0x30">
    <title>Main Spark Advance - Low Octane</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base spark advance vs cylinder airmass x RPM, low-octane table. Retarded 0-10.5 deg relative to high octane at mid/high load. The PCM runs High minus (High - Low) x the learned octane scaler: scaler 0 = pure High, 1.0 = pure Low. After a reset or fault the scaler starts at 1.0 (all Low) and octane learn moves it toward High while there is no knock (E0296). Effect: increase = more timing &amp; torque (and more knock risk) Evidence: ledger:E0002, ledger:E0003, ledger:E0005, ledger:E0006, ledger:E0069, ledger:E0071, ledger:E0175, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E0296, ledger:E1297</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2DAA5" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x2" flags="0x30">
    <title>PE enable throttle vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle opening, by engine speed, at or above which power enrichment is allowed (a barometric adder curve, all zero on the stock calibration, is added to it). Power enrichment also needs manifold pressure at or above the minimum MAP and rpm at or above the minimum rpm. Effect: lower = power enrichment starts at a smaller throttle opening Evidence: ledger:E0032, ledger:E0106, ledger:E0162, ledger:E0197, ledger:E0236, ledger:E0257, ledger:E0260, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x295F4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3" flags="0x0">
    <title>PE enable hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once power enrichment is active, the throttle threshold drops by this much, so it stays on until the throttle closes this far below the enable value. Effect: raise = power enrichment holds on longer as the throttle closes Evidence: ledger:E0032, ledger:E0147, ledger:E0151, ledger:E0194, ledger:E0197, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x295C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4" flags="0x0">
    <title>Stoichiometric AFR</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0024, ledger:E0143, ledger:E0151</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26EFE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>AFR</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5" flags="0x0">
    <title>Minimum commanded EQ under lean offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0033, ledger:E0151, ledger:E0195, ledger:E0212</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26F00" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ (fuel/air, 1.0 = stoich; lambda = 1/EQ)</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6" flags="0x0">
    <title>Maximum commanded EQ (state 2)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0033, ledger:E0151, ledger:E0195, ledger:E0212</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26F02" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ (fuel/air, 1.0 = stoich; lambda = 1/EQ)</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x7" flags="0x30">
    <title>Open-loop EQ, in gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0041, ledger:E0043, ledger:E0120, ledger:E0121, ledger:E0164, ledger:E0175, ledger:E0196, ledger:E0211, ledger:E0213, ledger:E0222, ledger:E0257, ledger:E0260, ledger:E0288, ledger:E0785, ledger:E1329</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant at start)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>degC (modelled temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28CA0" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x8" flags="0x30">
    <title>Open-loop EQ, park/neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0041, ledger:E0043, ledger:E0120, ledger:E0121, ledger:E0164, ledger:E0175, ledger:E0196, ledger:E0211, ledger:E0213, ledger:E0222, ledger:E0272, ledger:E0288, ledger:E0785, ledger:E1329</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant at start)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>degC (modelled temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29108" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9" flags="0x30">
    <title>MAF transfer curve (airflow vs output frequency)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Effect: increase = PCM believes more air is entering (richer fuelling) Evidence: ledger:E0042, ledger:E0110, ledger:E0111, ledger:E0112, ledger:E0113, ledger:E0114, ledger:E0175, ledger:E0219, ledger:E0230, ledger:E0685</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>Hz (MAF output frequency)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1500" />
      <LABEL index="1" value="1800" />
      <LABEL index="2" value="2100" />
      <LABEL index="3" value="2400" />
      <LABEL index="4" value="2700" />
      <LABEL index="5" value="3000" />
      <LABEL index="6" value="3300" />
      <LABEL index="7" value="3600" />
      <LABEL index="8" value="3900" />
      <LABEL index="9" value="4200" />
      <LABEL index="10" value="4500" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5100" />
      <LABEL index="13" value="5400" />
      <LABEL index="14" value="5700" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6300" />
      <LABEL index="17" value="6600" />
      <LABEL index="18" value="6900" />
      <LABEL index="19" value="7200" />
      <LABEL index="20" value="7500" />
      <LABEL index="21" value="7800" />
      <LABEL index="22" value="8100" />
      <LABEL index="23" value="8400" />
      <LABEL index="24" value="8700" />
      <LABEL index="25" value="9000" />
      <LABEL index="26" value="9300" />
      <LABEL index="27" value="9600" />
      <LABEL index="28" value="9900" />
      <LABEL index="29" value="10200" />
      <LABEL index="30" value="10500" />
      <LABEL index="31" value="10800" />
      <LABEL index="32" value="11100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CA1E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA" flags="0x30">
    <title>Engine speed limiter retard gain by state</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Read only in gear (states 0-5). Cells 1st-4th are the gears; 5th/6th are unused on the 4L60-E (E0271). Evidence: ledger:E0029, ledger:E0195, ledger:E0211, ledger:E0271</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>gear (in-gear trans state 0..5)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="5th" />
      <LABEL index="5" value="6th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22BC8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB" flags="0x0">
    <title>Vehicle speed limit - fuel cut CUTOFF</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0052, ledger:E0129, ledger:E0143, ledger:E0151</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x204EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC" flags="0x0">
    <title>Vehicle speed limit - fuel cut RESUME</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0052, ledger:E0129, ledger:E0143, ledger:E0151</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x204E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD" flags="0x0">
    <title>Vehicle speed limiter minimum RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0052, ledger:E0151, ledger:E0195</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x31AEE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE" flags="0x30">
    <title>Vehicle speed limiter retard gain by gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Speed limiter: gain of the spark retard term on the speed above the limit, by transmission state. Cells one to four are the gears, the fifth has no state on this transmission, and the sixth is used in Park, Reverse and Neutral. Evidence: ledger:E0052, ledger:E0195, ledger:E0211, ledger:E0271, ledger:E1132</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>transmission state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="not used" />
      <LABEL index="5" value="Park / Reverse / Neutral" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31AF8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xF" flags="0x30">
    <title>Desired idle vs coolant temp - IN GEAR</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target idle speed vs engine coolant temperature with the transmission in gear. Lower than the park/neutral target at the same temperature, which is the expected direction for a GM automatic. Warm-up log matches the part of the curve shared with the other idle curve (186 samples at 47-88 C, mean error 4.7 rpm, E0115). Which curve is Park/Neutral and which is in-gear rests on code (E0123). Evidence: ledger:E0048, ledger:E0115, ledger:E0123, ledger:E0158, ledger:E0231</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AB90" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x10" flags="0x0">
    <title>Desired idle ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0049, ledger:E0151, ledger:E0195</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B07C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x11" flags="0x0">
    <title>Octane scaler default (reset/fault)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Octane scaler value after a reset or fault. Stock 1.0 = run the Low Octane spark table until octane learn moves toward High (E0296). Lower it to start closer to High octane. Evidence: ledger:E0007, ledger:E0151, ledger:E0193, ledger:E0296</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2BA3A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0..1</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x12" flags="0x0">
    <title>Knock retard threshold for octane learn</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum per-cylinder knock retard for an octane-learn step. Stock 2.0 deg. Evidence: ledger:E0008, ledger:E0151, ledger:E0193, ledger:E0218</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2BA38" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x13" flags="0x0">
    <title>Octane scaler decay gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0009, ledger:E0151, ledger:E0193</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2B9F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x14" flags="0x0">
    <title>Max cylinder octane-scaler spread</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0010, ledger:E0151, ledger:E0193</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2B876" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0..1</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x15" flags="0x30">
    <title>Catalyst Monitor - Storage Time Normaliser</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier applied to the measured catalyst oxygen storage time before it is compared with the storage time reference, by mean airflow during the lean fuel step (columns, 0 to 16 g/s) and modelled catalyst temperature (rows, 300 to 800 C). Higher values make the catalyst look better, so the efficiency code is less likely. Stock at 6 g/s: 3.84 at 300 C falling to 0.58 at 800 C; flat below 3 g/s. Effect: raise = the measured storage time counts for more, so a weak catalyst is less likely to set the efficiency code Evidence: ledger:E0002, ledger:E0056, ledger:E0133, ledger:E1021, ledger:E1189, ledger:E1191, ledger:E1297</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s (mean airflow over the test step)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.5" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="1.5" />
      <LABEL index="4" value="2" />
      <LABEL index="5" value="2.5" />
      <LABEL index="6" value="3" />
      <LABEL index="7" value="3.5" />
      <LABEL index="8" value="4" />
      <LABEL index="9" value="4.5" />
      <LABEL index="10" value="5" />
      <LABEL index="11" value="5.5" />
      <LABEL index="12" value="6" />
      <LABEL index="13" value="6.5" />
      <LABEL index="14" value="7" />
      <LABEL index="15" value="7.5" />
      <LABEL index="16" value="8" />
      <LABEL index="17" value="8.5" />
      <LABEL index="18" value="9" />
      <LABEL index="19" value="9.5" />
      <LABEL index="20" value="10" />
      <LABEL index="21" value="10.5" />
      <LABEL index="22" value="11" />
      <LABEL index="23" value="11.5" />
      <LABEL index="24" value="12" />
      <LABEL index="25" value="12.5" />
      <LABEL index="26" value="13" />
      <LABEL index="27" value="13.5" />
      <LABEL index="28" value="14" />
      <LABEL index="29" value="14.5" />
      <LABEL index="30" value="15" />
      <LABEL index="31" value="15.5" />
      <LABEL index="32" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>degC (catalyst temperature model)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="300" />
      <LABEL index="1" value="362.5" />
      <LABEL index="2" value="425" />
      <LABEL index="3" value="487.5" />
      <LABEL index="4" value="550" />
      <LABEL index="5" value="612.5" />
      <LABEL index="6" value="675" />
      <LABEL index="7" value="737.5" />
      <LABEL index="8" value="800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x346EF" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x16" flags="0x0">
    <title>VE Model Cam Axis Source Switch (DO NOT TUNE)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stock 0 = the VE banks are indexed by the PCM&#x27;s primary actual-cam reading; non-zero switches to its alternate reading. Changes which signal drives the VE blend. Effect: DO NOT TUNE (selects the cam signal) Evidence: ledger:E0081, ledger:E0083, ledger:E0151</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C728" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x17" flags="0x30">
    <title>Octane-learn DECREASE gain vs A-B spark delta</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Octane-learn gain versus the A-B spark delta, 0 to 30 deg. Evidence: ledger:E0012, ledger:E0169, ledger:E0204</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>31</indexcount>
      <units>deg (high - low octane spark)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B9FA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="31" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x18" flags="0x30">
    <title>Octane-learn INCREASE gain vs per-cylinder knock retard</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Octane-learn gain versus knock retard, 0 to 20 deg; stock flat 0.10. Evidence: ledger:E0013, ledger:E0204, ledger:E0218, ledger:E0260</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>deg (per-cylinder knock retard)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="4" />
      <LABEL index="3" value="6" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="12" />
      <LABEL index="7" value="14" />
      <LABEL index="8" value="16" />
      <LABEL index="9" value="18" />
      <LABEL index="10" value="20" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B9E0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x19" flags="0x0">
    <title>Cylinder Count (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of cylinders: the count word that heads the firing order list and bounds the per-cylinder loops (knock, octane learn and others). Stock 5. Structural, not a tuning value. Do not edit. Effect: DO NOT EDIT Evidence: ledger:E0011, ledger:E0153, ledger:E1573</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x22C5C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cylinders</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1A" flags="0x30">
    <title>Injector flow-rate modifier (Q14) - vs battery voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Q14 multiplier on injector flow (effective flow = flow x X/16384). Stock: all 1.0 (no correction). Evidence: ledger:E0142, ledger:E0162, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>V (system voltage)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="5" />
      <LABEL index="1" value="6" />
      <LABEL index="2" value="7" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="9" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="11" />
      <LABEL index="7" value="12" />
      <LABEL index="8" value="13" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26564" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>3.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1B" flags="0x0">
    <title>Minimum RPM to allow DFCO</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum RPM to allow DFCO Evidence: ledger:E0146, ledger:E0151, ledger:E0236</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F156" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1C" flags="0x0">
    <title>Maximum RPM to disable DFCO</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Maximum RPM to disable DFCO Evidence: ledger:E0146, ledger:E0151, ledger:E0236</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F158" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1D" flags="0x0">
    <title>Dynamic Airflow MAF-Only - Engine Speed On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Dynamic airflow MAF-only mode: above the disable engine speed the cylinder airmass comes straight from the MAF (filtered), skipping the airmass predictor and its VE Maximum cap; it switches back below the re-enable engine speed. Below it, the airmass is capped at VE Maximum x barometric pressure / charge temperature, which holds boosted airmass near a naturally aspirated charge, so a boost tune either lowers this engine speed or raises VE Maximum. This is the engine speed at or above which MAF-only mode turns on. Stock 5000 rpm. Effect: lower = MAF-only airmass (no VE Maximum cap) from a lower engine speed; the usual boost ch...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2BD9A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E" flags="0x0">
    <title>Dynamic Airflow MAF-Only - Engine Speed Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Dynamic airflow MAF-only mode: above the disable engine speed the cylinder airmass comes straight from the MAF (filtered), skipping the airmass predictor and its VE Maximum cap; it switches back below the re-enable engine speed. Below it, the airmass is capped at VE Maximum x barometric pressure / charge temperature, which holds boosted airmass near a naturally aspirated charge, so a boost tune either lowers this engine speed or raises VE Maximum. This is the engine speed below which MAF-only mode turns off again. Stock 4900 rpm. Keep it a little below the on speed. Effect: lower = MAF-only mode holds down to a lower engine s...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2BD9C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1F" flags="0x0">
    <title>Power Enrichment Minimum MAP</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Manifold pressure at or above which power enrichment is allowed (with the throttle and rpm conditions). There is no upper limit, so it stays allowed at any boost level. Stock 55 kPa. Effect: lower = power enrichment allowed at lighter load Evidence: ledger:E0147, ledger:E0151, ledger:E0236, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x295CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x20" flags="0x0">
    <title>Power Enrichment Minimum MAP Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once power enrichment is active, the minimum manifold pressure drops by this much, so it stays on until pressure falls this far below the minimum. Stock 5 kPa. Effect: raise = power enrichment holds on at lower manifold pressure Evidence: ledger:E0147, ledger:E0151, ledger:E0236, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x295CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x21" flags="0x0">
    <title>Power Enrichment Delay RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Power enrichment delay applies only at or below this engine speed. Stock 8000 rpm, so the delay rules below apply across the whole range. Effect: lower = no power enrichment delay above this rpm Evidence: ledger:E0147, ledger:E0151, ledger:E0236, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x295D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x22" flags="0x0">
    <title>Power Enrichment minimum RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at or above which power enrichment is allowed. Stock 0 rpm (no rpm limit). Effect: raise = no power enrichment below this rpm Evidence: ledger:E0147, ledger:E0151, ledger:E0194, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x295C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x23" flags="0x0">
    <title>Power Enrichment minimum RPM hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once power enrichment is active, the minimum rpm drops by this much. Stock 0 rpm. Effect: raise = power enrichment holds on to a lower rpm once active Evidence: ledger:E0147, ledger:E0151, ledger:E0194, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x295C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x24" flags="0x30">
    <title>VE Maximum (Airmass Cap)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below the dynamic airflow MAF-only engine speed (stock 5000 rpm), the cylinder airmass that spark and fuel use is capped at this maximum VE x barometric pressure / charge temperature x the limit multiplier (and x the learned MAF to VE ratio when that is above 1.0). Barometric pressure, not MAP, so under boost this cap holds the airmass near a naturally aspirated full charge whatever the MAF reads: stock about 0.70 g per cylinder at 2000 rpm and 0.84 g at 5000 rpm (100 kPa, 20 C). Above the MAF-only engine speed the cap is skipped. Same unit as the VE banks: 2439 = 100 % volumetric efficiency on this engine. Raise for boost, o...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C93A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mg K/kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X*0.0625"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x25" flags="0x30">
    <title>Open Loop EQ Ratio Min vs. ECT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Evidence: ledger:E0148, ledger:E0160, ledger:E0175, ledger:E0196, ledger:E0236, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x271C2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X*0.0009765625"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x26" flags="0x30">
    <title>Closed Loop O2 Ready ECT vs. Startup Coolant Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Axis variable is the startup-ECT snapshot. One cold start is consistent: 23.9 C startup predicts 28.4 C, and trims first moved between 27.2 and 28.9 C (2026-09-20 log). Trim activity is a proxy for closed loop; one start only. Evidence: ledger:E0148, ledger:E0164, ledger:E0172, ledger:E0175, ledger:E0236, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant at start)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29926" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>3</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x27" flags="0x30">
    <title>Burst Knock Retard Mult vs. IAT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Evidence: ledger:E0148, ledger:E0160, ledger:E0172, ledger:E0175, ledger:E0234, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (intake air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B8C6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X*0.000030517578125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x28" flags="0x30">
    <title>Knock Retard Amount</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Evidence: ledger:E0148, ledger:E0160, ledger:E0175, ledger:E0196, ledger:E0234, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B6CC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>deg</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X*0.0001220703125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x29" flags="0x30">
    <title>Knock Retard Amount ECT Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the knock retard step by coolant temperature (1.0 = no change). The step itself grows with the knock sensor&#x27;s intensity, so this sets how hard the PCM pulls timing per knock event at each temperature. Evidence: ledger:E0148, ledger:E0160, ledger:E0175, ledger:E0196, ledger:E0234, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B6F0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X*0.000030517578125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x2A" flags="0x30">
    <title>ETC TPS Max vs. RPM vs. % Max Available Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. On the H3 this is the throttle needed for a torque request, used as a throttle ceiling (mode 2) or floor (mode 1) during torque intervention, not only a max. Row axis = density-corrected indicated torque (request + losses, x baro x IAT multipliers). Evidence: ledger:E0148, ledger:E0196, ledger:E0213, ledger:E0218, ledger:E0236, ledger:E0243, ledger:E0257, ledger:E0259, ledger:E0260</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="450" />
      <LABEL index="2" value="900" />
      <LABEL index="3" value="1350" />
      <LABEL index="4" value="1800" />
      <LABEL index="5" value="2250" />
      <LABEL index="6" value="2700" />
      <LABEL index="7" value="3150" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4050" />
      <LABEL index="10" value="4500" />
      <LABEL index="11" value="4950" />
      <LABEL index="12" value="5400" />
      <LABEL index="13" value="5850" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="7000" />
      <LABEL index="16" value="8191" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>engine torque (lb-ft; stored Nm x4)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-110.6" />
      <LABEL index="1" value="-73.8" />
      <LABEL index="2" value="-36.9" />
      <LABEL index="3" value="0.0" />
      <LABEL index="4" value="11.1" />
      <LABEL index="5" value="22.1" />
      <LABEL index="6" value="33.2" />
      <LABEL index="7" value="44.3" />
      <LABEL index="8" value="55.3" />
      <LABEL index="9" value="66.4" />
      <LABEL index="10" value="77.4" />
      <LABEL index="11" value="88.5" />
      <LABEL index="12" value="99.6" />
      <LABEL index="13" value="110.6" />
      <LABEL index="14" value="121.7" />
      <LABEL index="15" value="132.8" />
      <LABEL index="16" value="143.8" />
      <LABEL index="17" value="154.9" />
      <LABEL index="18" value="166.0" />
      <LABEL index="19" value="177.0" />
      <LABEL index="20" value="188.1" />
      <LABEL index="21" value="199.1" />
      <LABEL index="22" value="210.2" />
      <LABEL index="23" value="221.3" />
      <LABEL index="24" value="232.3" />
      <LABEL index="25" value="243.4" />
      <LABEL index="26" value="254.5" />
      <LABEL index="27" value="265.5" />
      <LABEL index="28" value="276.6" />
      <LABEL index="29" value="287.6" />
      <LABEL index="30" value="298.7" />
      <LABEL index="31" value="309.8" />
      <LABEL index="32" value="320.8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31616" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X*0.00152587890625"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x2B" flags="0x30">
    <title>Retard vs. % Torque Reduction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Evidence: ledger:E0148, ledger:E0167, ledger:E0175, ledger:E0196, ledger:E0234, ledger:E0243, ledger:E0936</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>% torque reduction</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="3.125" />
      <LABEL index="2" value="6.25" />
      <LABEL index="3" value="9.375" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="15.625" />
      <LABEL index="6" value="18.75" />
      <LABEL index="7" value="21.875" />
      <LABEL index="8" value="25" />
      <LABEL index="9" value="28.125" />
      <LABEL index="10" value="31.25" />
      <LABEL index="11" value="34.375" />
      <LABEL index="12" value="37.5" />
      <LABEL index="13" value="40.625" />
      <LABEL index="14" value="43.75" />
      <LABEL index="15" value="46.875" />
      <LABEL index="16" value="50" />
      <LABEL index="17" value="53.125" />
      <LABEL index="18" value="56.25" />
      <LABEL index="19" value="59.375" />
      <LABEL index="20" value="62.5" />
      <LABEL index="21" value="65.625" />
      <LABEL index="22" value="68.75" />
      <LABEL index="23" value="71.875" />
      <LABEL index="24" value="75" />
      <LABEL index="25" value="78.125" />
      <LABEL index="26" value="81.25" />
      <LABEL index="27" value="84.375" />
      <LABEL index="28" value="87.5" />
      <LABEL index="29" value="90.625" />
      <LABEL index="30" value="93.75" />
      <LABEL index="31" value="96.875" />
      <LABEL index="32" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31A94" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x2C" flags="0x30">
    <title>AC Compressor Torque vs. AC Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque model: A/C compressor torque by engine speed and A/C head pressure. It is added to the second A/C torque table (by intake air temperature); the sum is the compressor torque counted as an accessory load while the A/C clutch is on. Effect: raise = more engine torque is allowed for the A/C compressor Evidence: ledger:E0148, ledger:E0167, ledger:E0196, ledger:E0213, ledger:E0236, ledger:E0242, ledger:E0243, ledger:E0257, ledger:E0260, ledger:E1114, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (A/C pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="225" />
      <LABEL index="2" value="450" />
      <LABEL index="3" value="675" />
      <LABEL index="4" value="900" />
      <LABEL index="5" value="1125" />
      <LABEL index="6" value="1350" />
      <LABEL index="7" value="1575" />
      <LABEL index="8" value="1800" />
      <LABEL index="9" value="2025" />
      <LABEL index="10" value="2250" />
      <LABEL index="11" value="2475" />
      <LABEL index="12" value="2700" />
      <LABEL index="13" value="2925" />
      <LABEL index="14" value="3150" />
      <LABEL index="15" value="3375" />
      <LABEL index="16" value="3600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="400" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1200" />
      <LABEL index="4" value="1600" />
      <LABEL index="5" value="2000" />
      <LABEL index="6" value="2400" />
      <LABEL index="7" value="2800" />
      <LABEL index="8" value="3200" />
      <LABEL index="9" value="3600" />
      <LABEL index="10" value="4000" />
      <LABEL index="11" value="4400" />
      <LABEL index="12" value="4800" />
      <LABEL index="13" value="5200" />
      <LABEL index="14" value="5600" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30324" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>lb-ft</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6042.016932</max>
      <MATH equation="X*0.0921952686597"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x2D" flags="0x30">
    <title>Base Dwell Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Placed on the H3 by code-layout prediction. Evidence: ledger:E0150, ledger:E0165, ledger:E0175, ledger:E0196, ledger:E0213, ledger:E0234, ledger:E0257, ledger:E0260, ledger:E1358</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>22</indexcount>
      <units>V (ignition)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="4.5" />
      <LABEL index="1" value="5.5" />
      <LABEL index="2" value="6.5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="8.5" />
      <LABEL index="5" value="9.5" />
      <LABEL index="6" value="10.5" />
      <LABEL index="7" value="11.5" />
      <LABEL index="8" value="12.5" />
      <LABEL index="9" value="13.5" />
      <LABEL index="10" value="14.5" />
      <LABEL index="11" value="15.5" />
      <LABEL index="12" value="16.5" />
      <LABEL index="13" value="17.5" />
      <LABEL index="14" value="18.5" />
      <LABEL index="15" value="19.5" />
      <LABEL index="16" value="20.5" />
      <LABEL index="17" value="21.5" />
      <LABEL index="18" value="22.5" />
      <LABEL index="19" value="23.5" />
      <LABEL index="20" value="24.5" />
      <LABEL index="21" value="25.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F40E" mmedelementsizebits="16" mmedrowcount="22" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ms</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x2E" flags="0x30">
    <title>Base Dwell Time Modifier vs. IGNV vs. ECT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Placed on the H3 by code-layout prediction. Column axis is a modelled temperature (mostly coolant, pulled down by IAT and vehicle speed), not raw coolant (E0258). Evidence: ledger:E0150, ledger:E0165, ledger:E0175, ledger:E0196, ledger:E0234, ledger:E0257, ledger:E0258, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>degC (modelled temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <LABEL index="9" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>22</indexcount>
      <units>V (ignition)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="4.5" />
      <LABEL index="1" value="5.5" />
      <LABEL index="2" value="6.5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="8.5" />
      <LABEL index="5" value="9.5" />
      <LABEL index="6" value="10.5" />
      <LABEL index="7" value="11.5" />
      <LABEL index="8" value="12.5" />
      <LABEL index="9" value="13.5" />
      <LABEL index="10" value="14.5" />
      <LABEL index="11" value="15.5" />
      <LABEL index="12" value="16.5" />
      <LABEL index="13" value="17.5" />
      <LABEL index="14" value="18.5" />
      <LABEL index="15" value="19.5" />
      <LABEL index="16" value="20.5" />
      <LABEL index="17" value="21.5" />
      <LABEL index="18" value="22.5" />
      <LABEL index="19" value="23.5" />
      <LABEL index="20" value="24.5" />
      <LABEL index="21" value="25.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F6FD" mmedelementsizebits="8" mmedrowcount="22" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>0.996094</max>
      <MATH equation="X*0.00390625"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x2F" flags="0x30">
    <title>Burst Knock Retard Mult vs. RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Placed on the H3 by code-layout prediction. Evidence: ledger:E0150, ledger:E0160, ledger:E0172, ledger:E0175, ledger:E0196, ledger:E0234, ledger:E0260</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B8EE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X*0.0000152587890625"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x30" flags="0x30">
    <title>Burst Knock Retard vs. Cylair Delta</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Placed on the H3 by code-layout prediction. Evidence: ledger:E0150, ledger:E0167, ledger:E0196, ledger:E0234, ledger:E0936</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/cyl (airmass rise)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.002" />
      <LABEL index="2" value="0.004" />
      <LABEL index="3" value="0.006" />
      <LABEL index="4" value="0.008" />
      <LABEL index="5" value="0.01" />
      <LABEL index="6" value="0.012" />
      <LABEL index="7" value="0.014" />
      <LABEL index="8" value="0.016" />
      <LABEL index="9" value="0.018" />
      <LABEL index="10" value="0.02" />
      <LABEL index="11" value="0.022" />
      <LABEL index="12" value="0.024" />
      <LABEL index="13" value="0.026" />
      <LABEL index="14" value="0.028" />
      <LABEL index="15" value="0.03" />
      <LABEL index="16" value="0.032" />
      <LABEL index="17" value="0.034" />
      <LABEL index="18" value="0.036" />
      <LABEL index="19" value="0.038" />
      <LABEL index="20" value="0.04" />
      <LABEL index="21" value="0.042" />
      <LABEL index="22" value="0.044" />
      <LABEL index="23" value="0.046" />
      <LABEL index="24" value="0.048" />
      <LABEL index="25" value="0.05" />
      <LABEL index="26" value="0.052" />
      <LABEL index="27" value="0.054" />
      <LABEL index="28" value="0.056" />
      <LABEL index="29" value="0.058" />
      <LABEL index="30" value="0.06" />
      <LABEL index="31" value="0.062" />
      <LABEL index="32" value="0.064" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B882" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x31" flags="0x30">
    <title>Knock Retard Amount Baro Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the knock retard step by barometric pressure (1.0 = no change). The step itself grows with the knock sensor&#x27;s intensity, so this sets how hard the PCM pulls timing per knock event at each altitude. Evidence: ledger:E0150, ledger:E0162, ledger:E0175, ledger:E0196, ledger:E0234, ledger:E0257, ledger:E0260</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="55" />
      <LABEL index="1" value="65" />
      <LABEL index="2" value="75" />
      <LABEL index="3" value="85" />
      <LABEL index="4" value="95" />
      <LABEL index="5" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B714" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X*0.000030517578125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x32" flags="0x30">
    <title>DFCO Entry Spark</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark used on entry to decel fuel cut-off, vs airmass and rpm. Every cell is 0 deg on the stock H3 (not used by this calibration) (E0178). Effect: stock H3 = 0 everywhere; leave as is Evidence: ledger:E0178, ledger:E0210, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.20" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.40" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F19D" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x33" flags="0x30">
    <title>Misfire Detection Threshold - Cylinder Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor, cylinder mode: the PCM times each crank segment (one cylinder&#x27;s share of rotation) and looks at how far one segment departs from the trend of its neighbours (a third difference of consecutive segment times). A departure at or above this many microseconds is taken as a misfire of that cylinder. Rows are load (0 to 100 %), columns engine speed (400 to 7000 rpm); the value is interpolated. A raw value of 32767 (16000 us) in a cell or its neighbours switches this mode off there. Stock uses cylinder mode from 400 to below 1200 rpm and revolution mode from 1200 to below 6500 rpm. Effect: lower = smaller crank...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x38AB0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>26</indexcount>
      <units>rpm</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>% load</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6" />
      <LABEL index="2" value="12" />
      <LABEL index="3" value="19" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31" />
      <LABEL index="6" value="37" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56" />
      <LABEL index="10" value="62" />
      <LABEL index="11" value="69" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81" />
      <LABEL index="14" value="87" />
      <LABEL index="15" value="94" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38AEA" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>us</units>
      <decimalpl>1</decimalpl>
      <min>-16000.000000</min>
      <max>15999.511719</max>
      <MATH equation="X/2.048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x34" flags="0x30">
    <title>Misfire Detection Threshold - Revolution Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor, revolution mode (used at higher engine speed): a combined measure of crank segment time disturbance across a revolution, in microseconds of segment time. A value at or above this threshold is taken as a misfire. Rows are load (0 to 100 %), columns engine speed (400 to 7000 rpm); the value is interpolated. A raw value of 32767 (16000 us) in a cell or its neighbours switches this mode off there. Stock uses cylinder mode from 400 to below 1200 rpm and revolution mode from 1200 to below 6500 rpm. Effect: lower = smaller crank speed disturbances are counted as misfires (more sensitive) Evidence: ledger:E0179, ledg...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x38AB0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>26</indexcount>
      <units>rpm</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>% load</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6" />
      <LABEL index="2" value="12" />
      <LABEL index="3" value="19" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31" />
      <LABEL index="6" value="37" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56" />
      <LABEL index="10" value="62" />
      <LABEL index="11" value="69" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81" />
      <LABEL index="14" value="87" />
      <LABEL index="15" value="94" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38E62" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>us</units>
      <decimalpl>1</decimalpl>
      <min>-16000.000000</min>
      <max>15999.511719</max>
      <MATH equation="X/2.048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x35" flags="0x30">
    <title>Fuel Cutoff RPM (P/N) vs Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-speed fuel cut-off in Park/Neutral vs engine temperature (ECT blended toward IAT when cold). Stock H3 5000 rpm flat (E0181). Effect: P/N rev limit; raise with care Evidence: ledger:E0168, ledger:E0181, ledger:E0213, ledger:E0260, ledger:E0782, ledger:E1413</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (ECT blended toward IAT when cold)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22BD6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x36" flags="0x30">
    <title>Closed Loop Enable Coolant vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant temperature needed before closed loop is allowed, vs coolant at start-up. Stock H3 70 C (cold start) .. 55 C (E0184) Effect: raise = later closed loop Evidence: ledger:E0184, ledger:E0210, ledger:E0257, ledger:E0260, ledger:E1329</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x298C6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x37" flags="0x30">
    <title>Knock Retard Recovery Rate vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the remaining knock retard that is given back at each update, vs rpm. The update runs four times a second, and every cylinder&#x27;s retard is reduced by this share each time. Stock 25 % up to 1200 rpm and 20 % from 1600 rpm, which leaves about 41 % of the retard after one second at speed. Correction: releases up to v3.16 showed this curve as a time step in seconds, which was wrong. Effect: larger = timing comes back faster after knock; 0 = retard is never given back Evidence: ledger:E0184, ledger:E0210, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1164, ledger:E1166, ledger:E1329</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="400" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1200" />
      <LABEL index="4" value="1600" />
      <LABEL index="5" value="2000" />
      <LABEL index="6" value="2400" />
      <LABEL index="7" value="2800" />
      <LABEL index="8" value="3200" />
      <LABEL index="9" value="3600" />
      <LABEL index="10" value="4000" />
      <LABEL index="11" value="4400" />
      <LABEL index="12" value="4800" />
      <LABEL index="13" value="5200" />
      <LABEL index="14" value="5600" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6400" />
      <LABEL index="17" value="6800" />
      <LABEL index="18" value="7200" />
      <LABEL index="19" value="7600" />
      <LABEL index="20" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B846" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% per update</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x38" flags="0x30">
    <title>Minimum Dwell Time Mult vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier giving the minimum allowed coil dwell, vs rpm. Stock H3 0.8 flat (E0184) Effect: leave stock Evidence: ledger:E0184, ledger:E0210, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1358</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F7F2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x39" flags="0x30">
    <title>DFCO Enable TPS vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle must be below this for decel fuel cut-off to enable. Stock H3 0.15 % (E0187) Effect: decel fuel cut-off behaviour Evidence: ledger:E0187, ledger:E0197, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1358</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F07C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3A" flags="0x30">
    <title>DFCO Disable TPS vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle above this ends decel fuel cut-off. Stock H3 0.30 % (E0187) Effect: decel fuel cut-off behaviour Evidence: ledger:E0187, ledger:E0197, ledger:E0213, ledger:E0260, ledger:E1358</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F0A0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3B" flags="0x30">
    <title>DFCO Enable CylAir vs RPM</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 values]; COUNT is a structure word - never edit it (E0187). Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cylinder airmass must be below this for DFCO to enable (two rows, picked by a flag). Stock H3 0.19 -&gt; 0.09 g Effect: decel fuel cut-off behaviour Evidence: ledger:E0187, ledger:E0257, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="1024" />
      <LABEL index="4" value="1536" />
      <LABEL index="5" value="2048" />
      <LABEL index="6" value="2560" />
      <LABEL index="7" value="3072" />
      <LABEL index="8" value="3584" />
      <LABEL index="9" value="4096" />
      <LABEL index="10" value="4608" />
      <LABEL index="11" value="5120" />
      <LABEL index="12" value="5632" />
      <LABEL index="13" value="6144" />
      <LABEL index="14" value="6656" />
      <LABEL index="15" value="7168" />
      <LABEL index="16" value="7680" />
      <LABEL index="17" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="row 0" />
      <LABEL index="1" value="row 1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F0C2" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/cyl</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8.191875</max>
      <MATH equation="X/8000"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3C" flags="0x30">
    <title>DFCO Disable CylAir vs RPM</title>
    <description>Change in small steps and log. Each row is [COUNT u16 = 17][17 values]; COUNT is a structure word - never edit it (E0187). Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cylinder airmass above this ends DFCO (two rows, picked by a flag). Stock H3 0.21 -&gt; 0.11 g Effect: decel fuel cut-off behaviour Evidence: ledger:E0187, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>COUNT + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="COUNT" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="1024" />
      <LABEL index="4" value="1536" />
      <LABEL index="5" value="2048" />
      <LABEL index="6" value="2560" />
      <LABEL index="7" value="3072" />
      <LABEL index="8" value="3584" />
      <LABEL index="9" value="4096" />
      <LABEL index="10" value="4608" />
      <LABEL index="11" value="5120" />
      <LABEL index="12" value="5632" />
      <LABEL index="13" value="6144" />
      <LABEL index="14" value="6656" />
      <LABEL index="15" value="7168" />
      <LABEL index="16" value="7680" />
      <LABEL index="17" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="row 0" />
      <LABEL index="1" value="row 1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F10A" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/cyl</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8.191875</max>
      <MATH equation="X/8000"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3D" flags="0x30">
    <title>DFCO Enable Speed vs Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed needed for DFCO to enable, per gear. Stock H3 18.6 mph (1-3) / 49.7 mph (4-6) (E0187) Indexed by transmission state: cells 1st-4th are the gears, 5th/6th unused on the 4L60-E (E0271). Effect: decel fuel cut-off behaviour Evidence: ledger:E0187, ledger:E0211, ledger:E0271</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>gear (in-gear trans state 0..5)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="5th" />
      <LABEL index="5" value="6th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F15A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E" flags="0x30">
    <title>DFCO Disable Speed vs Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed below which DFCO ends, per gear. Stock H3 17.4 mph (1-3) / 38.5 mph (4-6) (E0187) Indexed by transmission state: cells 1st-4th are the gears, 5th/6th unused on the 4L60-E (E0271). Effect: decel fuel cut-off behaviour Evidence: ledger:E0187, ledger:E0211, ledger:E0271</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>gear (in-gear trans state 0..5)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="5th" />
      <LABEL index="5" value="6th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F166" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mph</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>318.137196</max>
      <MATH equation="X/205.996032"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3F" flags="0x0">
    <title>Minimum ECT to allow DFCO</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum ECT to allow DFCO (E0187) Evidence: ledger:E0187</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F172" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x40" flags="0x0">
    <title>Maximum ECT to disable DFCO</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Maximum ECT to disable DFCO (E0187) Evidence: ledger:E0187</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F174" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x41" flags="0x30">
    <title>Maximum Dwell Time Mult vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier giving the maximum allowed coil dwell, vs rpm. Stock H3 1.35 flat (E0189) Effect: leave stock Evidence: ledger:E0189, ledger:E0210, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1358</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F816" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x42" flags="0x0">
    <title>RPM Limit Hysteresis (Gear)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rev-limiter hysteresis in gear. Stock H3 300 rpm (E0190) Evidence: ledger:E0190</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22B98" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x43" flags="0x0">
    <title>RPM Limit Hysteresis (Park/Neutral)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rev-limiter hysteresis in Park/Neutral. Stock H3 300 rpm (E0190) Evidence: ledger:E0190</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22BF8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x44" flags="0x0">
    <title>LTFT Min ECT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel-trim learning allowed above this coolant temp. Stock H3 40 C (E0190) Evidence: ledger:E0190, ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24AF4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x45" flags="0x0">
    <title>LTFT Max ECT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel-trim learning allowed below this coolant temp. Stock H3 120 C (E0190) Evidence: ledger:E0190, ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24AF6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x46" flags="0x0">
    <title>Knock Learn Min MAP</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Octane/knock learning only above this MAP. Stock H3 55 kPa (E0191) Evidence: ledger:E0191</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2BA3C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x47" flags="0x0">
    <title>Knock Learn Min RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Octane/knock learning only above this rpm. Stock H3 1125 rpm (E0191) Evidence: ledger:E0191</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2BA3E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x48" flags="0x0">
    <title>Knock Learn Min Coolant Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learning only above this coolant temp. Stock H3 56 C (E0191) Evidence: ledger:E0191</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2BA40" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x49" flags="0x0">
    <title>Knock Learn Min IAT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Learning only above this intake air temp. Stock H3 -32.5 C (E0191) Evidence: ledger:E0191</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2BA42" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A" flags="0x0">
    <title>A/C WOT Cut - Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: the cut starts when throttle rises above this, while engine speed is below the cut RPM limit. Stock 100 % (never), and the cut is also turned off by its maximum time of 0. Effect: lower = the cut starts at less throttle Evidence: ledger:E0192, ledger:E0197, ledger:E1009</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2041E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4B" flags="0x0">
    <title>A/C WOT Cut - Re-Enable Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: the cut is released (after the release hold time) once throttle falls below this. Stock 100 %. Effect: lower = throttle must fall further before the compressor returns Evidence: ledger:E0192, ledger:E0197, ledger:E1009</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20420" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4C" flags="0x0">
    <title>A/C WOT Cut - RPM Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: the cut only applies while engine speed is below this. Stock 6500 rpm. Effect: lower = the cut only applies at lower rpm Evidence: ledger:E0192, ledger:E1009</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20422" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4D" flags="0x0">
    <title>A/C WOT Cut - RPM Limit Reset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: once engine speed rises above this the cut no longer applies. Stock 6500 rpm. Effect: raise = the cut keeps applying to a higher rpm Evidence: ledger:E0192, ledger:E1009</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20424" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x4E" flags="0x30">
    <title>Idle Base Spark vs RPM vs Airmass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base spark at idle, vs rpm (400..1600) and cylinder airmass. Stock H3 4..25 deg (E0202) Effect: idle quality / idle torque reserve Evidence: ledger:E0202, ledger:E0210, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1297</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1000" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1400" />
      <LABEL index="6" value="1600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E84D" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4F" flags="0x30">
    <title>AC Compressor Torque vs IAT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque model: extra A/C compressor torque by engine speed and intake air temperature (0 below 50 C on stock). It is added to the A/C torque table by head pressure; the sum is the compressor torque counted as an accessory load while the A/C clutch is on. Effect: raise = more engine torque is allowed for the A/C compressor in hot air Evidence: ledger:E0203, ledger:E0210, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1114, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (IAT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-30" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="-10" />
      <LABEL index="3" value="0" />
      <LABEL index="4" value="10" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="40" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="60" />
      <LABEL index="10" value="70" />
      <LABEL index="11" value="80" />
      <LABEL index="12" value="90" />
      <LABEL index="13" value="100" />
      <LABEL index="14" value="110" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="130" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="400" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1200" />
      <LABEL index="4" value="1600" />
      <LABEL index="5" value="2000" />
      <LABEL index="6" value="2400" />
      <LABEL index="7" value="2800" />
      <LABEL index="8" value="3200" />
      <LABEL index="9" value="3600" />
      <LABEL index="10" value="4000" />
      <LABEL index="11" value="4400" />
      <LABEL index="12" value="4800" />
      <LABEL index="13" value="5200" />
      <LABEL index="14" value="5600" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3056C" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>lb-ft</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>6042.016932</max>
      <MATH equation="X*0.0921952686597"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x50" flags="0x30">
    <title>Injection Timing (second pulse) - RPM Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. End-of-injection angle term for the second injection pulse by engine speed, in crank degrees of the 720 degree cycle. The coolant term and the engine speed term are added and capped at 720 deg. Stock 0 everywhere. Effect: raise = second injection pulse ends later in the engine cycle Evidence: ledger:E0317, ledger:E1182, ledger:E1329</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm (medium-res engine speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="128" />
      <LABEL index="2" value="256" />
      <LABEL index="3" value="384" />
      <LABEL index="4" value="512" />
      <LABEL index="5" value="640" />
      <LABEL index="6" value="768" />
      <LABEL index="7" value="896" />
      <LABEL index="8" value="1024" />
      <LABEL index="9" value="1152" />
      <LABEL index="10" value="1280" />
      <LABEL index="11" value="1408" />
      <LABEL index="12" value="1536" />
      <LABEL index="13" value="1664" />
      <LABEL index="14" value="1792" />
      <LABEL index="15" value="1920" />
      <LABEL index="16" value="2048" />
      <LABEL index="17" value="2176" />
      <LABEL index="18" value="2304" />
      <LABEL index="19" value="2432" />
      <LABEL index="20" value="2560" />
      <LABEL index="21" value="2688" />
      <LABEL index="22" value="2816" />
      <LABEL index="23" value="2944" />
      <LABEL index="24" value="3072" />
      <LABEL index="25" value="3200" />
      <LABEL index="26" value="3328" />
      <LABEL index="27" value="3456" />
      <LABEL index="28" value="3584" />
      <LABEL index="29" value="3712" />
      <LABEL index="30" value="3840" />
      <LABEL index="31" value="3968" />
      <LABEL index="32" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x253BE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg (crank, end of injection)</units>
      <decimalpl>2</decimalpl>
      <min>-1024.000000</min>
      <max>1023.968750</max>
      <MATH equation="X/32"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x51" flags="0x30">
    <title>Cranking VE vs MAP vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Volumetric efficiency used while cranking, vs rpm (0..1280) and MAP (15..105 kPa). Stock H3 59..100 pct (E0206) Effect: cranking fuel - affects hot/cold start Evidence: ledger:E0206, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1329</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="15" />
      <LABEL index="1" value="26" />
      <LABEL index="2" value="38" />
      <LABEL index="3" value="49" />
      <LABEL index="4" value="60" />
      <LABEL index="5" value="71" />
      <LABEL index="6" value="82" />
      <LABEL index="7" value="94" />
      <LABEL index="8" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="40" />
      <LABEL index="2" value="80" />
      <LABEL index="3" value="120" />
      <LABEL index="4" value="160" />
      <LABEL index="5" value="200" />
      <LABEL index="6" value="240" />
      <LABEL index="7" value="280" />
      <LABEL index="8" value="320" />
      <LABEL index="9" value="360" />
      <LABEL index="10" value="400" />
      <LABEL index="11" value="440" />
      <LABEL index="12" value="480" />
      <LABEL index="13" value="520" />
      <LABEL index="14" value="560" />
      <LABEL index="15" value="600" />
      <LABEL index="16" value="640" />
      <LABEL index="17" value="680" />
      <LABEL index="18" value="720" />
      <LABEL index="19" value="760" />
      <LABEL index="20" value="800" />
      <LABEL index="21" value="840" />
      <LABEL index="22" value="880" />
      <LABEL index="23" value="920" />
      <LABEL index="24" value="960" />
      <LABEL index="25" value="1000" />
      <LABEL index="26" value="1040" />
      <LABEL index="27" value="1080" />
      <LABEL index="28" value="1120" />
      <LABEL index="29" value="1160" />
      <LABEL index="30" value="1200" />
      <LABEL index="31" value="1240" />
      <LABEL index="32" value="1280" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2BAE0" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x52" flags="0x30">
    <title>Cranking VE Baro Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier on cranking VE vs barometric pressure (60..105 kPa, 10 points). Stock H3 1.64 at 60 kPa -&gt; 1.0 at 100-105 kPa (E0206) Effect: altitude cranking fuel Evidence: ledger:E0206, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1329</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="60" />
      <LABEL index="1" value="65" />
      <LABEL index="2" value="70" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="80" />
      <LABEL index="5" value="85" />
      <LABEL index="6" value="90" />
      <LABEL index="7" value="95" />
      <LABEL index="8" value="100" />
      <LABEL index="9" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2BD36" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x53" flags="0x30">
    <title>Open Loop Hot-Restart Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra open-loop fuel after a hot restart. A latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, this table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. Columns are coolant temperature; rows are the fuel injected since the engine started, so the extra fuel fades as the engine burns fue...</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="56" />
      <LABEL index="1" value="62" />
      <LABEL index="2" value="68" />
      <LABEL index="3" value="74" />
      <LABEL index="4" value="80" />
      <LABEL index="5" value="86" />
      <LABEL index="6" value="92" />
      <LABEL index="7" value="98" />
      <LABEL index="8" value="104" />
      <LABEL index="9" value="110" />
      <LABEL index="10" value="116" />
      <LABEL index="11" value="122" />
      <LABEL index="12" value="128" />
      <LABEL index="13" value="134" />
      <LABEL index="14" value="140" />
      <LABEL index="15" value="146" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g fuel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="5.5" />
      <LABEL index="2" value="10.9" />
      <LABEL index="3" value="16.4" />
      <LABEL index="4" value="21.9" />
      <LABEL index="5" value="27.4" />
      <LABEL index="6" value="32.8" />
      <LABEL index="7" value="38.3" />
      <LABEL index="8" value="43.8" />
      <LABEL index="9" value="49.3" />
      <LABEL index="10" value="54.7" />
      <LABEL index="11" value="60.2" />
      <LABEL index="12" value="65.7" />
      <LABEL index="13" value="71.2" />
      <LABEL index="14" value="76.6" />
      <LABEL index="15" value="82.1" />
      <LABEL index="16" value="87.6" />
      <LABEL index="17" value="93.1" />
      <LABEL index="18" value="98.5" />
      <LABEL index="19" value="104.0" />
      <LABEL index="20" value="109.5" />
      <LABEL index="21" value="115.0" />
      <LABEL index="22" value="120.4" />
      <LABEL index="23" value="125.9" />
      <LABEL index="24" value="131.4" />
      <LABEL index="25" value="136.9" />
      <LABEL index="26" value="142.3" />
      <LABEL index="27" value="147.8" />
      <LABEL index="28" value="153.3" />
      <LABEL index="29" value="158.8" />
      <LABEL index="30" value="164.2" />
      <LABEL index="31" value="169.7" />
      <LABEL index="32" value="175.2" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x27FB0" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x54" flags="0x30">
    <title>Pedal to throttle-area demand - gears 1-3 + Park/Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: the rows of this map are engine speed in rpm on this calibration (the pedal map row input switch is set here; on the H3 the rows are vehicle speed), shown by running this operating system&#x27;s code. Which transmission state uses this map is set by the item Pedal Map Select vs Trans State - Normal in this file; the stock selection on this calibration can differ from the H3 described below, so check that table on your own bin before editing this map. Accelerator pedal -&gt; throttle demand for gears 1/2/3 and Park/Neutral: pedal % (columns) x vehicle speed (rows) -&gt; % of the PCM&#x27;s are...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x23DE6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x23E0A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (engine speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2326E" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x55" flags="0x30">
    <title>Pedal to throttle-area demand - 4th gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: the rows of this map are engine speed in rpm on this calibration (the pedal map row input switch is set here; on the H3 the rows are vehicle speed), shown by running this operating system&#x27;s code. Which transmission state uses this map is set by the item Pedal Map Select vs Trans State - Normal in this file; the stock selection on this calibration can differ from the H3 described below, so check that table on your own bin before editing this map. Accelerator pedal -&gt; throttle demand for 4th gear (overdrive): pedal % (columns) x vehicle speed (rows) -&gt; % of the PCM&#x27;s area-&gt;throt...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x23DE6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x23E0A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (engine speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x233A6" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x56" flags="0x0">
    <title>A/C-on idle target</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Desired idle requested while the A/C compressor is engaged (and held while stopped); wins the max-of-requests, so it only matters when above the coolant-curve target. Stock 675 rpm (reads 672 on PID 11C9) (E0231, E0238) Effect: idle speed with A/C on Evidence: ledger:E0231, ledger:E0238</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2AB86" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x57" flags="0x0">
    <title>Idle request ramp step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Step per update by which each ramped idle request (A/C and others) moves toward its target; stock 5 rpm (E0231, E0238) Effect: how quickly idle-up requests ramp in/out Evidence: ledger:E0231, ledger:E0238</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B07E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x58" flags="0x30">
    <title>Reduced-power (ETC fault) pedal curve</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal -&gt; throttle-area demand used only in ETC reduced-power (fault) mode; stock caps at 8 % area. DO NOT TUNE - fault-mode protection (E0228, E0239) Effect: limp-home throttle Evidence: ledger:E0228, ledger:E0239</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="6.2" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.8" />
      <LABEL index="4" value="25.0" />
      <LABEL index="5" value="31.2" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.8" />
      <LABEL index="8" value="50.0" />
      <LABEL index="9" value="56.2" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.8" />
      <LABEL index="12" value="75.0" />
      <LABEL index="13" value="81.2" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.8" />
      <LABEL index="16" value="100.0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23D62" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle area</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x59" flags="0x30">
    <title>ETC monitor: max expected throttle vs request</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest throttle request the ETC rationality monitor accepts for the current pedal area demand; a request above it for longer than the over-limit time triggers the monitor. DO NOT TUNE - safety diagnostic Effect: throttle rationality monitor Evidence: ledger:E0228, ledger:E0239, ledger:E1124, ledger:E1329</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>% throttle area (request + idle term)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="3.1" />
      <LABEL index="2" value="6.2" />
      <LABEL index="3" value="9.4" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="15.6" />
      <LABEL index="6" value="18.8" />
      <LABEL index="7" value="21.9" />
      <LABEL index="8" value="25.0" />
      <LABEL index="9" value="28.1" />
      <LABEL index="10" value="31.2" />
      <LABEL index="11" value="34.4" />
      <LABEL index="12" value="37.5" />
      <LABEL index="13" value="40.6" />
      <LABEL index="14" value="43.8" />
      <LABEL index="15" value="46.9" />
      <LABEL index="16" value="50.0" />
      <LABEL index="17" value="53.1" />
      <LABEL index="18" value="56.2" />
      <LABEL index="19" value="59.4" />
      <LABEL index="20" value="62.5" />
      <LABEL index="21" value="65.6" />
      <LABEL index="22" value="68.8" />
      <LABEL index="23" value="71.9" />
      <LABEL index="24" value="75.0" />
      <LABEL index="25" value="78.1" />
      <LABEL index="26" value="81.2" />
      <LABEL index="27" value="84.4" />
      <LABEL index="28" value="87.5" />
      <LABEL index="29" value="90.6" />
      <LABEL index="30" value="93.8" />
      <LABEL index="31" value="96.9" />
      <LABEL index="32" value="100.0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x241B4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5A" flags="0x30">
    <title>Pedal Request Factor Authority vs Pedal Demand</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How much of the pedal request factor (the product of the pedal gain reduction, pedal gain increase and the other pedal factors, capped by the Pedal Request Factor Ceiling) is applied to the pedal demand, by pedal demand. 1.0 applies the factor in full, 0 ignores it so the pedal map value passes unchanged, 2.0 doubles its effect. Stock 1.0 everywhere. Range 0 to 2.0. Effect: lower = the pedal gain reduction and increase change the throttle demand less at that pedal demand Evidence: ledger:E0228, ledger:E0239, ledger:E0782, ledger:E1211, ledger:E1212, ledger:E1413</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% throttle area (pedal demand)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="6.2" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.8" />
      <LABEL index="4" value="25.0" />
      <LABEL index="5" value="31.2" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.8" />
      <LABEL index="8" value="50.0" />
      <LABEL index="9" value="56.2" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.8" />
      <LABEL index="12" value="75.0" />
      <LABEL index="13" value="81.2" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.8" />
      <LABEL index="16" value="100.0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23138" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5B" flags="0x30">
    <title>Pedal to throttle-area demand - Reverse</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: the rows of this map are engine speed in rpm on this calibration (the pedal map row input switch is set here; on the H3 the rows are vehicle speed), shown by running this operating system&#x27;s code. Which transmission state uses this map is set by the item Pedal Map Select vs Trans State - Normal in this file; the stock selection on this calibration can differ from the H3 described below, so check that table on your own bin before editing this map. Accelerator pedal -&gt; throttle-area demand for Reverse (normal range). Same layout/axes/scaling as pedal_throttle_area_main. Pointer-table slot k2 (E0240). Effe...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x23DE6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x23E0A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (engine speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x234DE" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5C" flags="0x30">
    <title>Pedal to throttle-area demand - 4WD-Low forward gears</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: the rows of this map are engine speed in rpm on this calibration (the pedal map row input switch is set here; on the H3 the rows are vehicle speed), shown by running this operating system&#x27;s code. Which transmission state uses this map in 4WD-Low is set by the item Pedal Map Select vs Trans State - 4WD-Low in this file; the stock selection on this calibration can differ from the H3 described below, so check that table on your own bin before editing this map. Accelerator pedal -&gt; throttle-area demand for 4WD-Low, all forward gears. Same layout/axes/scaling as pedal_throttle_area_main. Pointer-table slot...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x23DE6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x23E0A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (engine speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23616" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5D" flags="0x30">
    <title>Pedal to throttle-area demand - 4WD-Low Park/Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: the rows of this map are engine speed in rpm on this calibration (the pedal map row input switch is set here; on the H3 the rows are vehicle speed), shown by running this operating system&#x27;s code. Which transmission state uses this map in 4WD-Low is set by the item Pedal Map Select vs Trans State - 4WD-Low in this file; the stock selection on this calibration can differ from the H3 described below, so check that table on your own bin before editing this map. Accelerator pedal -&gt; throttle-area demand for 4WD-Low, Park/Neutral. Same layout/axes/scaling as pedal_throttle_area_main. Pointer-table slot k4 (E...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x23DE6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x23E0A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (engine speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2374E" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5E" flags="0x30">
    <title>Pedal to throttle-area demand - 4WD-Low Reverse</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: the rows of this map are engine speed in rpm on this calibration (the pedal map row input switch is set here; on the H3 the rows are vehicle speed), shown by running this operating system&#x27;s code. Which transmission state uses this map in 4WD-Low is set by the item Pedal Map Select vs Trans State - 4WD-Low in this file; the stock selection on this calibration can differ from the H3 described below, so check that table on your own bin before editing this map. Accelerator pedal -&gt; throttle-area demand for 4WD-Low, Reverse. Same layout/axes/scaling as pedal_throttle_area_main. Pointer-table slot k5 (E0240)...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x23DE6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x23E0A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (engine speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23886" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5F" flags="0x30">
    <title>Pedal to Throttle-Area Demand - Slot k6 (mode 2, forward gears and Park / Neutral)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: the rows of this map are engine speed in rpm on this calibration (the pedal map row input switch is set here; on the H3 the rows are vehicle speed), shown by running this operating system&#x27;s code. Which transmission state uses this map is set by a pedal mode 2 selector that is not in this file; the stock selection on this calibration can differ from the H3 described below. Pedal map (pedal % by vehicle speed to throttle-area demand) in slot k6, used for forward gears and Park / Neutral while pedal mode 2 is selected. Pedal mode 2 is selected while byte 0 of a message the PCM receives on the vehicle bus car...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x23DE6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x23E0A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (engine speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x239BE" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x60" flags="0x30">
    <title>Pedal to Throttle-Area Demand - Slot k8 (mode 2, Reverse)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: the rows of this map are engine speed in rpm on this calibration (the pedal map row input switch is set here; on the H3 the rows are vehicle speed), shown by running this operating system&#x27;s code. Which transmission state uses this map is set by a pedal mode 2 selector that is not in this file; the stock selection on this calibration can differ from the H3 described below. Pedal map (pedal % by vehicle speed to throttle-area demand) in slot k8, used for Reverse while pedal mode 2 is selected. Pedal mode 2 is selected while byte 0 of a message the PCM receives on the vehicle bus carries state 1 or 2; state...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x23DE6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x23E0A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (engine speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23C2E" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x61" flags="0x0">
    <title>Final Drive Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Axle ratio used to compute vehicle speed from the output-shaft sensor. Stock H3 4.56. Change it together with tire revs when the axle gearing changes. Live 2026-09-23: the PCM&#x27;s own vehicle speed matches this pair within 1.0 %. The PCM computes speed from output-shaft speed using these same constants, so that confirms the decode, not your actual tire size or axle ratio. Check a new setting against GPS. Shift points and converter lockup do not use this value: the transmission computes its own speed from a separate axle ratio and tire size. Those two are traced but not yet released, so after a tire or gear change the shift...</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x20064" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>:1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x62" flags="0x0">
    <title>VSS Tire Revs per Distance</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tire revolutions per mile (stored as revs/km x32). Stock H3 627.6/mi (~32.1 in tire). Lower it for taller tires to correct the speedometer. Live 2026-09-23: the PCM&#x27;s own vehicle speed matches this pair within 1.0 %. The PCM computes speed from output-shaft speed using these same constants, so that confirms the decode, not your actual tire size or axle ratio. Check a new setting against GPS. Shift points and converter lockup do not use this value: the transmission computes its own speed from a separate axle ratio and tire size. Those two are traced but not yet released, so after a tire or gear change the shift points sti...</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x20066" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>revs/mi</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3295.886220</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*0.05029200"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x63" flags="0x30">
    <title>Torque per airmass vs RPM vs EQ</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Indicated torque per gram of cylinder air (all 5 cylinders) vs rpm and fuelling EQ; gross torque = airmass x this x MAP correction. Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0280, ledger:E1314</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>EQ</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.8" />
      <LABEL index="1" value="0.9" />
      <LABEL index="2" value="1.0" />
      <LABEL index="3" value="1.1" />
      <LABEL index="4" value="1.2" />
      <LABEL index="5" value="1.3" />
      <LABEL index="6" value="1.4" />
      <LABEL index="7" value="1.5" />
      <LABEL index="8" value="1.6" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30934" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm per g</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1197.337557</max>
      <MATH equation="X*0.0182702"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x64" flags="0x30">
    <title>Torque loss vs spark retard from MBT</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of gross torque lost when final spark is below the torque-model MBT spark. Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0280, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>deg retard</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="3" />
      <LABEL index="2" value="6" />
      <LABEL index="3" value="9" />
      <LABEL index="4" value="12" />
      <LABEL index="5" value="15" />
      <LABEL index="6" value="18" />
      <LABEL index="7" value="21" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="27" />
      <LABEL index="10" value="30" />
      <LABEL index="11" value="33" />
      <LABEL index="12" value="36" />
      <LABEL index="13" value="39" />
      <LABEL index="14" value="42" />
      <LABEL index="15" value="45" />
      <LABEL index="16" value="48" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30A68" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% torque lost</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x65" flags="0x30">
    <title>Torque model MBT spark vs airmass vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Optimal (MBT) spark the torque model compares final spark against; used only for the spark-loss term. Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0280, ledger:E1314</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g airmass</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.20" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.40" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.60" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.80" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1.00" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.20" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30AA3" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x66" flags="0x30">
    <title>Torque model MBT spark adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the torque-model MBT spark; by cam-phase factor (0 to 0.24 in 0.03 steps); stock all 0. Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0255, ledger:E0280, ledger:E0896, ledger:E1577</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>cam-phase factor</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.03" />
      <LABEL index="2" value="0.06" />
      <LABEL index="3" value="0.09" />
      <LABEL index="4" value="0.12" />
      <LABEL index="5" value="0.15" />
      <LABEL index="6" value="0.18" />
      <LABEL index="7" value="0.21" />
      <LABEL index="8" value="0.24" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30A8C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x67" flags="0x30">
    <title>Engine friction vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Friction torque vs rpm (enters the loss sum at half weight; the math includes that). Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0280, ledger:E0936, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x307D4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x68" flags="0x30">
    <title>Coolant-dependent friction vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Friction torque vs rpm at the warm multiplier (x torque_friction_coolant_mult). Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0280, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x307B0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x69" flags="0x30">
    <title>Friction multiplier vs coolant vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier on the coolant-dependent friction; stock 2.4 when coldest to 1.0 warm. Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0254, ledger:E0280, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (corrected coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="50" />
      <LABEL index="4" value="80" />
      <LABEL index="5" value="110" />
      <LABEL index="6" value="140" />
      <LABEL index="7" value="170" />
      <LABEL index="8" value="200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x307FC" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>3.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6A" flags="0x30">
    <title>Load-dependent torque loss vs airmass vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Loss torque vs airmass and rpm, added to friction. Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0280, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>g airmass</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.40" />
      <LABEL index="2" value="0.72" />
      <LABEL index="3" value="1.04" />
      <LABEL index="4" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30F24" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x6B" flags="0x0">
    <title>Engine inertia torque factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales filtered engine acceleration into the inertia torque the PCM subtracts from its engine torque estimate. Part of the torque model, which reproduces logged delivered torque at steady load within about 6 %. Shift pressure, torque reduction, converter clutch and throttle torque control all use that estimate. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (torque model) Evidence: ledger:E0246, ledger:E0280, ledger:E0899</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30318" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x6C" flags="0x30">
    <title>COT enrichment EQ cap vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Maximum commanded EQ during catalyst over-temp enrichment. Stock 1.18..1.40. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249, ledger:E1329</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26EB6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6D" flags="0x30">
    <title>COT enrichment ramp-in step vs coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EQ added per update while COT enrichment ramps in. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249, ledger:E1329</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26E6A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ per update</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6E" flags="0x30">
    <title>COT enrichment ramp-out step vs coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EQ removed per update after COT conditions end. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249, ledger:E1329</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26E8E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ per update</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x6F" flags="0x0">
    <title>Over-temp enrichment start coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine over-temp enrichment adds EQ above this coolant temperature. Stock 110 C. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26E58" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x70" flags="0x0">
    <title>Over-temp enrichment gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EQ added per degree above the start temperature. Stock 0.05. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26E5A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ per degC</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x71" flags="0x0">
    <title>Over-temp enrichment EQ cap</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Maximum commanded EQ from over-temp enrichment. Stock 2.0. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26E5C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x72" flags="0x0">
    <title>Over-temp enrichment delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the over-temp conditions must hold before enrichment. Stock 2 s. Protection enrichment - DO NOT TUNE (E0249) Effect: protection enrichment Evidence: ledger:E0249</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26E64" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x73" flags="0x0">
    <title>MAF-fault mode 2: VE cap factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In MAF-fault mode 2 the fuel airmass is min(MAF, VE x this). Stock 0.995. Fault handling - DO NOT TUNE (E0219, E0253) Effect: MAF / VE airflow arbitration Evidence: ledger:E0219, ledger:E0253</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2BADA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x74" flags="0x0">
    <title>MAF-fault mode 2: filter coefficient</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter on the mode-2 capped airmass. Stock 0.110. Fault handling - DO NOT TUNE (E0219, E0253) Effect: MAF / VE airflow arbitration Evidence: ledger:E0219, ledger:E0253</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2BAD8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x75" flags="0x0">
    <title>Steady-state fuel airmass filter toward MAF</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the steady-state fuel airmass follows MAF airmass. Stock 0.150. (E0219, E0253) Effect: MAF / VE airflow arbitration Evidence: ledger:E0219, ledger:E0253</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2BD9E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x76" flags="0x0">
    <title>Learned MAF/VE ratio filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the learned MAF/VE ratio adapts in steady state. Stock 0.018. (E0219, E0253) Effect: MAF / VE airflow arbitration Evidence: ledger:E0219, ledger:E0253</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2BDA2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x77" flags="0x0">
    <title>Learned MAF/VE ratio maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper clamp on the learned MAF/VE ratio. Stock 1.5. (E0219, E0253) Effect: MAF / VE airflow arbitration Evidence: ledger:E0219, ledger:E0253</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2BDA4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x78" flags="0x0">
    <title>Learned MAF/VE ratio minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower clamp on the learned MAF/VE ratio. Stock 0.5. (E0219, E0253) Effect: MAF / VE airflow arbitration Evidence: ledger:E0219, ledger:E0253</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2BDA6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x79" flags="0x0">
    <title>Learned MAF/VE Ratio - Reset Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM learns a MAF to VE airflow ratio in steady state and uses it on the VE airflow during transients. While manifold pressure is below the deep vacuum MAP (closed throttle decel) learning is frozen; on the first update back above it, a learned ratio below the reset threshold is put back to 1.0, and a higher one is kept. This is the reset threshold: a learned ratio below it is reset to 1.0 after each deep vacuum episode. Stock 1.05. Effect: raise = more learned ratios are thrown away after decel; 0 = never reset Evidence: ledger:E0219, ledger:E0253, ledger:E0856</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2BDA8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A" flags="0x0">
    <title>Traction Control - Cold Engine Coolant Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control: at or below this coolant temperature the engine reports torque control as not available to the other modules. On this calibration the torque reduction through the throttle still acts when it is requested. Stock -40 C. Effect: raise = torque control is reported as not available up to a warmer engine Evidence: ledger:E0256, ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3027C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B" flags="0x0">
    <title>Traction Control Fuel Cut Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lets a traction control request cut fuel. 1: when the brake / traction module asks for less torque and traction control is active, the PCM may cut fuel, unless Traction Control Fuel Cut Inhibit is set. 0 (stock): traction control never cuts fuel; it still reduces torque through the throttle. Has no effect without a traction control module on the bus. Effect: 1 = traction control may cut fuel (needs inhibit 0); 0 = stock Evidence: ledger:E0256, ledger:E1744</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x302C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = allowed, 0 = off (stock)</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7C" flags="0x0">
    <title>Traction Control Fuel Cut Inhibit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Blocks traction control fuel cut. 1 (stock): traction control never cuts fuel, whatever the enable says. 0: fuel cut follows Traction Control Fuel Cut Enable. Has no effect without a traction control module on the bus. Effect: 0 = fuel cut follows the enable; 1 = stock (blocked) Evidence: ledger:E0256, ledger:E1744</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20466" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = blocked (stock), 0 = not blocked</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x7D" flags="0x30">
    <title>ETC torque request baro multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the indicated torque request before the ETC torque-to-throttle table. Stock 1.35 at 65 kPa down to 0.95 at 105 kPa (E0259) Effect: increase = more throttle for the same torque request Evidence: ledger:E0259, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="65" />
      <LABEL index="1" value="75" />
      <LABEL index="2" value="85" />
      <LABEL index="3" value="95" />
      <LABEL index="4" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30FF4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7E" flags="0x30">
    <title>ETC torque request IAT multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the indicated torque request before the ETC torque-to-throttle table. Stock 0.89 cold, 1.00 at 45-79 C, 1.19 at 140 C (E0259) Effect: increase = more throttle for the same torque request Evidence: ledger:E0259, ledger:E1358</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (IAT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28.75" />
      <LABEL index="2" value="-17.5" />
      <LABEL index="3" value="-6.25" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="16.25" />
      <LABEL index="6" value="27.5" />
      <LABEL index="7" value="38.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="61.25" />
      <LABEL index="10" value="72.5" />
      <LABEL index="11" value="83.75" />
      <LABEL index="12" value="95" />
      <LABEL index="13" value="106.25" />
      <LABEL index="14" value="117.5" />
      <LABEL index="15" value="128.75" />
      <LABEL index="16" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31000" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7F" flags="0x30">
    <title>O2 switch-point adder A phase-in delay vs startup coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Run time after start before O2 switch-point adder A (from O2 error via a curve) begins to phase in. Stock 200 s cold, 30 s hot. The adder biases the closed-loop rich/lean switch point. The oxygen sensor input here is the rear (post catalyst) sensor, bank 1 sensor 2. Effect: raise = closed-loop O2 correction arrives later / more gradually after a start Evidence: ledger:E0273, ledger:E0281, ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant at start)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28.75" />
      <LABEL index="2" value="-17.5" />
      <LABEL index="3" value="-6.25" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="16.25" />
      <LABEL index="6" value="27.5" />
      <LABEL index="7" value="38.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="61.25" />
      <LABEL index="10" value="72.5" />
      <LABEL index="11" value="83.75" />
      <LABEL index="12" value="95" />
      <LABEL index="13" value="106.25" />
      <LABEL index="14" value="117.5" />
      <LABEL index="15" value="128.75" />
      <LABEL index="16" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24C4C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x80" flags="0x30">
    <title>O2 switch-point adder A phase-in ramp time vs startup coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time over which O2 feedback term A ramps from 0 to full once its delay has passed. Stock 120 s cold, 30 s hot. The adder biases the closed-loop rich/lean switch point (E0281). The oxygen sensor input here is the rear (post catalyst) sensor, bank 1 sensor 2. Effect: raise = closed-loop O2 correction arrives later / more gradually after a start Evidence: ledger:E0273, ledger:E0281, ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant at start)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28.75" />
      <LABEL index="2" value="-17.5" />
      <LABEL index="3" value="-6.25" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="16.25" />
      <LABEL index="6" value="27.5" />
      <LABEL index="7" value="38.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="61.25" />
      <LABEL index="10" value="72.5" />
      <LABEL index="11" value="83.75" />
      <LABEL index="12" value="95" />
      <LABEL index="13" value="106.25" />
      <LABEL index="14" value="117.5" />
      <LABEL index="15" value="128.75" />
      <LABEL index="16" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24C94" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x81" flags="0x30">
    <title>O2 switch-point adder B phase-in delay vs startup coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Run time after start before O2 switch-point adder B (from filtered O2 via a curve) begins to phase in. Stock 200 s cold, 30 s hot. The adder biases the closed-loop rich/lean switch point. The oxygen sensor input here is the rear (post catalyst) sensor, bank 1 sensor 2. Effect: raise = closed-loop O2 correction arrives later / more gradually after a start Evidence: ledger:E0273, ledger:E0281, ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant at start)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28.75" />
      <LABEL index="2" value="-17.5" />
      <LABEL index="3" value="-6.25" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="16.25" />
      <LABEL index="6" value="27.5" />
      <LABEL index="7" value="38.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="61.25" />
      <LABEL index="10" value="72.5" />
      <LABEL index="11" value="83.75" />
      <LABEL index="12" value="95" />
      <LABEL index="13" value="106.25" />
      <LABEL index="14" value="117.5" />
      <LABEL index="15" value="128.75" />
      <LABEL index="16" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24C70" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x82" flags="0x30">
    <title>O2 switch-point adder B phase-in ramp time vs startup coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time over which O2 feedback term B ramps from 0 to full once its delay has passed. Stock 120 s cold, 5 s hot. The adder biases the closed-loop rich/lean switch point (E0281). The oxygen sensor input here is the rear (post catalyst) sensor, bank 1 sensor 2. Effect: raise = closed-loop O2 correction arrives later / more gradually after a start Evidence: ledger:E0273, ledger:E0281, ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant at start)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28.75" />
      <LABEL index="2" value="-17.5" />
      <LABEL index="3" value="-6.25" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="16.25" />
      <LABEL index="6" value="27.5" />
      <LABEL index="7" value="38.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="61.25" />
      <LABEL index="10" value="72.5" />
      <LABEL index="11" value="83.75" />
      <LABEL index="12" value="95" />
      <LABEL index="13" value="106.25" />
      <LABEL index="14" value="117.5" />
      <LABEL index="15" value="128.75" />
      <LABEL index="16" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24CB8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x83" flags="0x30">
    <title>Cranking Fuel Multiplier vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the cranking fuel amount by engine speed (0 to 1600 rpm). Stock 1.0 up to 300 rpm, 0.95 / 0.80 / 0.70 / 0.60 at 400 to 700 rpm and 0.5 from 800 rpm. It acts only on cranking fuel and on the crank-to-run blend that starts from it; running fuel does not use it, so it does not lean out a low idle. Effect: raise = more cranking fuel at that engine speed Evidence: ledger:E0277, ledger:E1090</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="100" />
      <LABEL index="2" value="200" />
      <LABEL index="3" value="300" />
      <LABEL index="4" value="400" />
      <LABEL index="5" value="500" />
      <LABEL index="6" value="600" />
      <LABEL index="7" value="700" />
      <LABEL index="8" value="800" />
      <LABEL index="9" value="900" />
      <LABEL index="10" value="1000" />
      <LABEL index="11" value="1100" />
      <LABEL index="12" value="1200" />
      <LABEL index="13" value="1300" />
      <LABEL index="14" value="1400" />
      <LABEL index="15" value="1500" />
      <LABEL index="16" value="1600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x249C0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x84" flags="0x0">
    <title>MAP Sensor Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Span of the MAP sensor: the pressure range the PCM reads between 0 V and 5 V (stock 94.1 kPa, so with the offset 10.4 to 104.5 kPa, a stock 1-bar sensor). MAP = offset + this x sensor volts / 5. Change it together with the offset and the filtered-path span when fitting a different MAP sensor. With a boost MAP sensor: the PCM&#x27;s barometric pressure estimate takes the MAP reading whenever MAP is higher than the current estimate, capped at 110 kPa. After the first boost the barometric pressure therefore reads 110 kPa (about 9 kPa high at sea level) until a full-throttle reading below barometric pressure or the next key-on co...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2CAAE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa across 0 to 5 V</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x85" flags="0x0">
    <title>MAP Sensor Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intercept of the MAP sensor conversion (kPa at 0 counts, added unsigned so it cannot go below 0). Stock 10.40 kPa. Shared by all three MAP conversion paths. With a boost MAP sensor: the PCM&#x27;s barometric pressure estimate takes the MAP reading whenever MAP is higher than the current estimate, capped at 110 kPa. After the first boost the barometric pressure therefore reads 110 kPa (about 9 kPa high at sea level) until a full-throttle reading below barometric pressure or the next key-on corrects it; the cap is fixed in the operating system. The MAP circuit high / low codes test the raw sensor signal, not the converted press...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2CAB0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa at 0 V</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x86" flags="0x0">
    <title>MAP Sensor Gain (filtered path)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Span used for the filtered MAP path. Keep it equal to MAP Sensor Gain as displayed (it is stored as half because that path runs at twice the scale). Stock 94.1 kPa across 0 to 5 V. Effect: keep equal to MAP Sensor Gain Evidence: ledger:E0278, ledger:E1462</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2CAB2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa across 0 to 5 V</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x87" flags="0x30">
    <title>O2 Switch Point - Base (per bank)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base O2 voltage above which closed loop calls the mixture rich, per bank. Stock 530 mV at the low end of its input falling to 340 mV. Lowering it makes closed loop run leaner, raising it richer. Column positions are set by the O2 Switch Point Airflow Map: stock 0 to 76 g/s, most columns below 30 g/s (E0290). Effect: raise = closed-loop fuelling runs richer Evidence: ledger:E0281, ledger:E0290</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24EE0" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x88" flags="0x30">
    <title>O2 Switch Point Adder vs O2 Activity</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Adder to the O2 switch point vs how fast the O2 voltage is changing, phased in after a start by the term-A delay/ramp. Stock 0 to +100 mV. The oxygen sensor input here is the rear (post catalyst) sensor, bank 1 sensor 2. Effect: raise = switch point moves up (richer) when the O2 signal is active Evidence: ledger:E0281, ledger:E0988, ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>mV (change of filtered O2 voltage over 10 updates)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-20" />
      <LABEL index="1" value="-18.75" />
      <LABEL index="2" value="-17.5" />
      <LABEL index="3" value="-16.25" />
      <LABEL index="4" value="-15" />
      <LABEL index="5" value="-13.75" />
      <LABEL index="6" value="-12.5" />
      <LABEL index="7" value="-11.25" />
      <LABEL index="8" value="-10" />
      <LABEL index="9" value="-8.75" />
      <LABEL index="10" value="-7.5" />
      <LABEL index="11" value="-6.25" />
      <LABEL index="12" value="-5" />
      <LABEL index="13" value="-3.75" />
      <LABEL index="14" value="-2.5" />
      <LABEL index="15" value="-1.25" />
      <LABEL index="16" value="0" />
      <LABEL index="17" value="1.25" />
      <LABEL index="18" value="2.5" />
      <LABEL index="19" value="3.75" />
      <LABEL index="20" value="5" />
      <LABEL index="21" value="6.25" />
      <LABEL index="22" value="7.5" />
      <LABEL index="23" value="8.75" />
      <LABEL index="24" value="10" />
      <LABEL index="25" value="11.25" />
      <LABEL index="26" value="12.5" />
      <LABEL index="27" value="13.75" />
      <LABEL index="28" value="15" />
      <LABEL index="29" value="16.25" />
      <LABEL index="30" value="17.5" />
      <LABEL index="31" value="18.75" />
      <LABEL index="32" value="20" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24D06" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x89" flags="0x30">
    <title>O2 Switch Point Adder vs Filtered O2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Adder to the O2 switch point vs the filtered O2 voltage, phased in after a start by the term-B delay/ramp. Stock +150 mV at 250 mV falling to -75 mV at high voltage. The oxygen sensor input here is the rear (post catalyst) sensor, bank 1 sensor 2. Effect: raise = switch point moves up (richer) at that O2 voltage Evidence: ledger:E0281, ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>mV</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="250" />
      <LABEL index="1" value="271.875" />
      <LABEL index="2" value="293.75" />
      <LABEL index="3" value="315.625" />
      <LABEL index="4" value="337.5" />
      <LABEL index="5" value="359.375" />
      <LABEL index="6" value="381.25" />
      <LABEL index="7" value="403.125" />
      <LABEL index="8" value="425" />
      <LABEL index="9" value="446.875" />
      <LABEL index="10" value="468.75" />
      <LABEL index="11" value="490.625" />
      <LABEL index="12" value="512.5" />
      <LABEL index="13" value="534.375" />
      <LABEL index="14" value="556.25" />
      <LABEL index="15" value="578.125" />
      <LABEL index="16" value="600" />
      <LABEL index="17" value="621.875" />
      <LABEL index="18" value="643.75" />
      <LABEL index="19" value="665.625" />
      <LABEL index="20" value="687.5" />
      <LABEL index="21" value="709.375" />
      <LABEL index="22" value="731.25" />
      <LABEL index="23" value="753.125" />
      <LABEL index="24" value="775" />
      <LABEL index="25" value="796.875" />
      <LABEL index="26" value="818.75" />
      <LABEL index="27" value="840.625" />
      <LABEL index="28" value="862.5" />
      <LABEL index="29" value="884.375" />
      <LABEL index="30" value="906.25" />
      <LABEL index="31" value="928.125" />
      <LABEL index="32" value="950" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24D4E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x8A" flags="0x0">
    <title>O2 Switch Point Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest O2 switch point allowed. Stock 300 mV. Effect: raise = closed loop cannot be biased as lean Evidence: ledger:E0281</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24DFA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8B" flags="0x0">
    <title>O2 Switch Point Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest O2 switch point allowed. Stock 675 mV. Effect: raise = closed loop can be biased richer Evidence: ledger:E0281</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24DFC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8C" flags="0x0">
    <title>O2 Switch Point Cold-Start Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the O2 switch point while the engine has run less than the time limit and coolant is below the temperature limit. Stock -150 mV (leaner bias when cold). Effect: raise = less lean bias just after a cold start Evidence: ledger:E0281</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24DCA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8D" flags="0x0">
    <title>O2 Switch Point Cold-Start Adder - Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Run time after start during which the cold-start adder applies. Stock 160 s. Effect: raise = cold-start bias lasts longer Evidence: ledger:E0281</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24DC6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8E" flags="0x0">
    <title>O2 Switch Point Cold-Start Adder - Coolant Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cold-start adder applies only below this coolant temperature. Stock 65 C. Effect: raise = cold-start bias applies to warmer starts Evidence: ledger:E0281</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24DC8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x8F" flags="0x0">
    <title>Idle Airflow Area Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit on the idle airflow (effective throttle area) command in normal running. Stock 3.33 % of full throttle area (about 30 g/s-equivalent at idle). The idle controller cannot open the throttle further than this at idle. Effect: raise = idle control can add more air (big cams, cold starts); too high risks runaway idle Evidence: ledger:E0282, ledger:E0283</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A18C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>182.041667</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/360"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x90" flags="0x0">
    <title>Idle Airflow Area Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower limit on the idle airflow command in normal running. Stock 0. Effect: raise = throttle never closes below this at idle Evidence: ledger:E0282, ledger:E0283</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A18E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>182.041667</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/360"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x91" flags="0x0">
    <title>Idle Airflow Area Maximum - Fault</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit used when a sensor-fault condition is active (e.g. MAF fault). Stock 11.4 %. Effect: limit used only with a fault present Evidence: ledger:E0282, ledger:E0283</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A188" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>182.041667</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/360"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x92" flags="0x0">
    <title>Idle Airflow Area Minimum - Fault</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower limit used when a sensor-fault condition is active. Stock 0. Effect: limit used only with a fault present Evidence: ledger:E0282, ledger:E0283</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A18A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>182.041667</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/360"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x93" flags="0x0">
    <title>Idle Airflow Area - Fault Default</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Command forced when the idle controller&#x27;s fault flag is set. Stock 0. Effect: value used only with that fault Evidence: ledger:E0282, ledger:E0283</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A190" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>182.041667</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/360"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x94" flags="0x30">
    <title>Idle Airflow - Coolant Adder</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle base airflow added vs coolant temperature. Stock +2.39 g/s at -40 C falling to 0 at 68-104 C and -0.12 g/s at 152 C. Adds directly to the idle airflow request, so it sets how much extra air a cold engine gets at idle. Row 1 = In Gear, row 2 = Park/Neutral. Effect: raise = more idle air (higher idle rpm before closed-loop trims it) at that coolant temperature Evidence: ledger:E0286, ledger:E0287</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A8F4" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x95" flags="0x30">
    <title>Idle Airflow vs Desired RPM Above Base</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added for the part of the desired idle rpm above the base desired-idle-vs-coolant value (and above the start-up flare), e.g. A/C or other idle-up requests. Stock In Gear 0 to 3.85 g/s, Park/Neutral 0 to 2.28 g/s over 0-400 rpm. Row 1 = In Gear, row 2 = Park/Neutral. Effect: raise = more air per rpm of idle-up request (faster, fuller idle-up) Evidence: ledger:E0286, ledger:E0287</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A81C" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x96" flags="0x30">
    <title>Idle Airflow vs Start-Up RPM Flare</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added for the start-up rpm flare (see Idle Start-Up RPM Flare). Stock In Gear 0 to 2.71 g/s, Park/Neutral 0 to 2.39 g/s at 200 rpm of flare and above. Row 1 = In Gear, row 2 = Park/Neutral. Effect: raise = more air during the post-start flare Evidence: ledger:E0286, ledger:E0287</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A8AC" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x97" flags="0x30">
    <title>Idle Airflow vs RPM Below Desired</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added only when engine rpm is below desired idle (droop catch), vs how far below after the droop gain. Stock 0 up to 175 rpm of droop, then rising to 5.0 g/s at 400 rpm. Row 1 = In Gear, row 2 = Park/Neutral. Effect: raise = stronger catch when idle sags (stall resistance); too much makes idle hunt Evidence: ledger:E0286, ledger:E0287</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A864" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x98" flags="0x30">
    <title>Idle Airflow - Barometric Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added vs barometric pressure (altitude). Stock -1.11 g/s at 60 kPa rising to 0 at 100 kPa. Effect: raise = more idle air at altitude Evidence: ledger:E0286, ledger:E0287</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="60" />
      <LABEL index="1" value="65" />
      <LABEL index="2" value="70" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="80" />
      <LABEL index="5" value="85" />
      <LABEL index="6" value="90" />
      <LABEL index="7" value="95" />
      <LABEL index="8" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A980" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x99" flags="0x30">
    <title>Idle Overspeed Spark / Droop Airflow Gain vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales rpm error vs coolant for two things: the overspeed idle spark tables and the rpm-below-desired input of Idle Airflow vs RPM Below Desired. Stock 1.0 everywhere (E0291). Effect: raise = the droop table reacts to smaller rpm sags Evidence: ledger:E0286, ledger:E0287, ledger:E0291</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B0E0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9A" flags="0x30">
    <title>Idle Start-Up RPM Flare - In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra desired idle rpm after a start (added to the desired idle vs coolant value, E0294) vs time since start (rows) and coolant (columns), In Gear. Stock 200 rpm at start (300 rpm at 20 and 32 C) decaying to 0 by 64 s. The Idle Airflow vs Start-Up RPM Flare table supplies the air for it; after 8 s it is cancelled once the truck moves or the throttle opens. Effect: raise = higher, longer rpm flare after starting Evidence: ledger:E0286, ledger:E0287, ledger:E0294</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>s since start</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2ABF2" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9B" flags="0x30">
    <title>Idle Airflow - Light-Off Retard Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added while catalyst light-off spark retard is active, vs the amount of retard, used normally. Stock 0 to 0.32 g/s. Effect: raise = more air to hold idle rpm while spark is retarded Evidence: ledger:E0286, ledger:E0287, ledger:E0294</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>deg retard</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A9DC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9C" flags="0x30">
    <title>Idle Airflow - Light-Off Retard Adder (A/C)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added while catalyst light-off spark retard is active, vs the amount of retard, used with A/C on (or the alternate state). Stock 0 to 0.64 g/s. Effect: raise = more air to hold idle rpm while spark is retarded Evidence: ledger:E0286, ledger:E0287, ledger:E0294</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>deg retard</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A9E8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9D" flags="0x30">
    <title>Idle Airflow - Alternator Load Adder vs RPM - In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added vs rpm (columns) and alternator field duty (rows, 0-100 %), In Gear. Stock 0 at the first row rising to 1.18 g/s at the last row from 512 rpm up. Effect: raise = more idle air when that load is present Evidence: ledger:E0286, ledger:E0287, ledger:E0294, ledger:E0936</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>% alternator field duty</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="25" />
      <LABEL index="2" value="50" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A718" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9E" flags="0x30">
    <title>Idle Airflow - Base vs RPM</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base idle airflow term vs engine speed, part of the closed-loop term. Stock 0.3 g/s at 400-800 rpm, 1.0 (In Gear) / 0.5 (Park/Neutral) at 1200 rpm, rising to 20 g/s at 6400 rpm. Row 1 = In Gear, row 2 = Park/Neutral. Effect: raise = more idle air at that rpm Evidence: ledger:E0287, ledger:E0289</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29D40" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x9F" flags="0x30">
    <title>Idle Airflow - RPM Adder (timed)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added by engine speed, 400 to 3600 rpm, while its timer gate allows (the gate timing itself is not fully traced). It passes straight into the idle throttle area. Stock 0 up to 1600 rpm, then 0.1 to 1.0 g/s at 3600 rpm (E0723). Effect: raise = more air when rpm is high with the throttle closed (softer return to idle) Evidence: ledger:E0287, ledger:E0289, ledger:E0723</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1000" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1400" />
      <LABEL index="6" value="1600" />
      <LABEL index="7" value="1800" />
      <LABEL index="8" value="2000" />
      <LABEL index="9" value="2200" />
      <LABEL index="10" value="2400" />
      <LABEL index="11" value="2600" />
      <LABEL index="12" value="2800" />
      <LABEL index="13" value="3000" />
      <LABEL index="14" value="3200" />
      <LABEL index="15" value="3400" />
      <LABEL index="16" value="3600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29E2C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA0" flags="0x30">
    <title>Idle Airflow Closed-Loop Step vs Airflow Error</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Step added to the idle airflow integral each control update, by airflow error (measured flow minus predicted idle airflow). STOCK IS ALL ZERO: the airflow integral is switched off on this calibration and idle rpm is held by the learn, the rpm-droop airflow table and idle spark. Filling it enables the integral; start very small. Row 1 = In Gear, row 2 = Park/Neutral. Effect: non-zero = enables airflow closed-loop idle; positive values for positive error remove air (check the sign on a log first) Evidence: ledger:E0287, ledger:E0289</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x29DF2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT; data columns: g/s airflow error)</units>
      <embedinfo type="1" />
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29CF8" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s per update</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA1" flags="0x30">
    <title>Idle Airflow Closed-Loop Error Gain vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the airflow error before the closed-loop step lookup, vs coolant. Stock 1.0. Effect: raise = the step table reacts to smaller errors Evidence: ledger:E0287, ledger:E0289</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A004" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA2" flags="0x30">
    <title>Idle Underspeed Spark Gain vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the idle underspeed spark tables (both P/N and In Gear) vs coolant. Stock 1.0 everywhere. Effect: raise = more spark advance added when idle rpm sags Evidence: ledger:E0291</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B0BC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA3" flags="0x30">
    <title>O2 Switch Point Airflow Map</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Maps used airflow onto the columns of O2 Switch Point - Base (value = column, 0 to 8). Stock reaches the last column at 76 g/s, so the base curve spends most of its resolution below 30 g/s. Effect: reshapes where along airflow each base switch-point column applies Evidence: ledger:E0290</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s used airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <LABEL index="17" value="68" />
      <LABEL index="18" value="72" />
      <LABEL index="19" value="76" />
      <LABEL index="20" value="80" />
      <LABEL index="21" value="84" />
      <LABEL index="22" value="88" />
      <LABEL index="23" value="92" />
      <LABEL index="24" value="96" />
      <LABEL index="25" value="100" />
      <LABEL index="26" value="104" />
      <LABEL index="27" value="108" />
      <LABEL index="28" value="112" />
      <LABEL index="29" value="116" />
      <LABEL index="30" value="120" />
      <LABEL index="31" value="124" />
      <LABEL index="32" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25078" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>base column</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA4" flags="0x30">
    <title>Throttle Follower Airflow vs RPM</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Follower airflow target vs rpm, before its throttle (stock 0.5), speed (0.68 at standstill), coolant and baro factors. Rows: normal In Gear, normal Park/Neutral, first idle after start In Gear, first idle P/N. Stock In Gear 2.4 (400 rpm) to 40 (6400 rpm). Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually ins...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B304" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA5" flags="0x30">
    <title>Throttle Follower Factor vs Throttle</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the follower target vs the current throttle. Rows: normal, first idle after start. Stock 0.5 everywhere. Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually instead of snapping shut (executed in the scheduler rig: a lift from 2000 rpm held about 3.5 g/s extra for about 0.8 s, then decayed to zero by abo...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x2B588" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT; data columns: % throttle)</units>
      <embedinfo type="1" />
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B424" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA6" flags="0x30">
    <title>Throttle Follower Factor vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the follower target vs vehicle speed. Stock 0.68 at 0-14 km/h, 1.0 above. Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually instead of snapping shut (executed in the scheduler rig: a lift from 2000 rpm held about 3.5 g/s extra for about 0.8 s, then decayed to zero by about 1.8 s; with the follower airflow table zeroed the extra air and throttle opening were absent). Effect: raise = more follower...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="14" />
      <LABEL index="2" value="28" />
      <LABEL index="3" value="42" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="70" />
      <LABEL index="6" value="84" />
      <LABEL index="7" value="98" />
      <LABEL index="8" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B5AE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>3.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA7" flags="0x30">
    <title>Throttle Follower Factor vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the follower target vs coolant. Stock 1.5 at 20 and 32 C, 1.0 elsewhere. Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually instead of snapping shut (executed in the scheduler rig: a lift from 2000 rpm held about 3.5 g/s extra for about 0.8 s, then decayed to zero by about 1.8 s; with the follower airflow table zeroed the extra air and throttle opening were absent). Effect: raise = more follower a...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B51E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA8" flags="0x30">
    <title>Throttle Follower Decay Step vs RPM</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the follower air bleeds off once the hold time has passed, per control update. Stock In Gear 0.005 g/s at 400 rpm to 0.09 g/s above 2000 rpm; P/N about half. Rows: In Gear, Park/Neutral. Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually instead of snapping shut (executed in the scheduler rig: a lift...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B394" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s per update</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>31.999512</max>
      <MATH equation="X/2048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xA9" flags="0x30">
    <title>Throttle Follower Decay Factor vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the decay step vs vehicle speed. Stock 1.0 to 42 km/h, rising to 5.0 at 63-105 km/h. Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually instead of snapping shut (executed in the scheduler rig: a lift from 2000 rpm held about 3.5 g/s extra for about 0.8 s, then decayed to zero by about 1.8 s; with the follower airflow table zeroed the extra air and throttle opening were absent). Effect: raise = fas...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="7" />
      <LABEL index="2" value="14" />
      <LABEL index="3" value="21" />
      <LABEL index="4" value="28" />
      <LABEL index="5" value="35" />
      <LABEL index="6" value="42" />
      <LABEL index="7" value="49" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="63" />
      <LABEL index="10" value="70" />
      <LABEL index="11" value="77" />
      <LABEL index="12" value="84" />
      <LABEL index="13" value="91" />
      <LABEL index="14" value="98" />
      <LABEL index="15" value="105" />
      <LABEL index="16" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B542" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAA" flags="0x30">
    <title>Throttle Follower Hold Time vs RPM</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the follower air is held before it starts to bleed off. Stock In Gear 0.1 s at 0-800 rpm, 1.0 s at 1200, 0.3-0.4 s above 2000. Rows: In Gear, Park/Neutral. Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually instead of snapping shut (executed in the scheduler rig: a lift from 2000 rpm held about 3.5 g...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B46C" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAB" flags="0x30">
    <title>Throttle Follower Hold Factor vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the hold time vs vehicle speed. Stock 2.0 at standstill, 1.5 at 7-35 km/h, 1.0 above. Part of the throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. After a throttle lift, this extra air is added to the commanded idle airflow and to the requested throttle opening, held, then bled off, so the throttle closes gradually instead of snapping shut (executed in the scheduler rig: a lift from 2000 rpm held about 3.5 g/s extra for about 0.8 s, then decayed to zero by about 1.8 s; with the follower airflow table zeroed the extra air and throttle opening were absent). Effect: raise = lo...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="7" />
      <LABEL index="2" value="14" />
      <LABEL index="3" value="21" />
      <LABEL index="4" value="28" />
      <LABEL index="5" value="35" />
      <LABEL index="6" value="42" />
      <LABEL index="7" value="49" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="63" />
      <LABEL index="10" value="70" />
      <LABEL index="11" value="77" />
      <LABEL index="12" value="84" />
      <LABEL index="13" value="91" />
      <LABEL index="14" value="98" />
      <LABEL index="15" value="105" />
      <LABEL index="16" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B566" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAC" flags="0x30">
    <title>Idle Airflow Kick - Shift into P/N</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short airflow kick after shifting into Park/Neutral, by accessory state (A/C off/on x a second flag off/on; the second flag is a dead/always-0 snapshot on stock, E0824). Stock 0.2 g/s. Added straight into the idle airflow request for about 0.2 s, then faded out (E0293). Effect: raise = more air right after shifting to P/N Evidence: ledger:E0287, ledger:E0293, ledger:E0824, ledger:E1113</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="base" />
      <LABEL index="1" value="A/C" />
      <LABEL index="2" value="row 2 (dead on stock)" />
      <LABEL index="3" value="row 3 (dead on stock)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B12E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAD" flags="0x30">
    <title>Idle Airflow Kick - Shift into Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short airflow kick after shifting into gear (the converter loads the engine), by accessory state (A/C off/on x a second flag off/on; the second flag is a dead/always-0 snapshot on stock, E0824). Stock 0.2 g/s. Added straight into the idle airflow request for about 0.2 s, then faded out (E0293). Effect: raise = more air right after shifting into gear (less rpm dip on engagement) Evidence: ledger:E0287, ledger:E0293, ledger:E0824</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="base" />
      <LABEL index="1" value="A/C" />
      <LABEL index="2" value="row 2 (dead on stock)" />
      <LABEL index="3" value="row 3 (dead on stock)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B136" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>31.999512</max>
      <MATH equation="X/2048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAE" flags="0x30">
    <title>Idle Airflow Shift into P/N Kick Factor vs Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the shift-into-P/N kick vs transmission fluid temperature. Stock 1.0. Added straight into the idle airflow request for about 0.2 s, then faded out (E0293). Effect: raise = bigger kick at that fluid temperature Evidence: ledger:E0287, ledger:E0293</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B1FA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xAF" flags="0x30">
    <title>Idle Airflow Shift into Gear Kick Factor vs Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the shift-into-gear kick vs transmission fluid temperature. Stock 1.0. Added straight into the idle airflow request for about 0.2 s, then faded out (E0293). Effect: raise = bigger kick at that fluid temperature Evidence: ledger:E0287, ledger:E0293</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B242" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB0" flags="0x0">
    <title>Idle Airflow Kick - Shift into P/N Duration</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the kick is held before it fades. Stock 0.2 s. Added straight into the idle airflow request for about 0.2 s, then faded out (E0293). Effect: raise = kick lasts longer Evidence: ledger:E0293</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B15A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB1" flags="0x0">
    <title>Idle Airflow Kick - Shift into Gear Duration</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the kick is held before it fades. Stock 0.2 s. Added straight into the idle airflow request for about 0.2 s, then faded out (E0293). Effect: raise = kick lasts longer Evidence: ledger:E0293</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B160" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB2" flags="0x30">
    <title>Idle Airflow - Post-Start (first second)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow added right after the engine starts, vs time since start (columns, 0.5 s steps) and coolant (rows), until the Post-Start Time Limit passes. Stock 1.5 to 3.0 g/s for about the first second; later columns are never reached on stock limits. Effect: raise = more air in the first moment after start (helps a stumble or dip right after crank) Evidence: ledger:E0287, ledger:E0294, ledger:E0936</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>s since start</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.5" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="1.5" />
      <LABEL index="4" value="2" />
      <LABEL index="5" value="2.5" />
      <LABEL index="6" value="3" />
      <LABEL index="7" value="3.5" />
      <LABEL index="8" value="4" />
      <LABEL index="9" value="4.5" />
      <LABEL index="10" value="5" />
      <LABEL index="11" value="5.5" />
      <LABEL index="12" value="6" />
      <LABEL index="13" value="6.5" />
      <LABEL index="14" value="7" />
      <LABEL index="15" value="7.5" />
      <LABEL index="16" value="8" />
      <LABEL index="17" value="8.5" />
      <LABEL index="18" value="9" />
      <LABEL index="19" value="9.5" />
      <LABEL index="20" value="10" />
      <LABEL index="21" value="10.5" />
      <LABEL index="22" value="11" />
      <LABEL index="23" value="11.5" />
      <LABEL index="24" value="12" />
      <LABEL index="25" value="12.5" />
      <LABEL index="26" value="13" />
      <LABEL index="27" value="13.5" />
      <LABEL index="28" value="14" />
      <LABEL index="29" value="14.5" />
      <LABEL index="30" value="15" />
      <LABEL index="31" value="15.5" />
      <LABEL index="32" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A242" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB3" flags="0x30">
    <title>Idle Airflow - Post-Start Time Limit (rpm above desired)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long after start the post-start airflow stays on, while rpm is above desired, vs coolant. Stock 1.5 s cold, 0.85 s from 20 C. Effect: raise = post-start air stays on longer Evidence: ledger:E0294</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A6A6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xB4" flags="0x30">
    <title>Idle Airflow - Post-Start Time Limit (rpm at or below desired)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long after start the post-start airflow stays on, while rpm is at or below desired, vs coolant. Stock 1.0 s cold, 0.85 s from 20 C. Effect: raise = post-start air stays on longer Evidence: ledger:E0294</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A6CA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xB5" flags="0x0">
    <title>Coolant Hot Flag - On Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant temperature above which the PCM sets its coolant-hot status flag (sent to other modules). Stock 125 C. Effect: raise = hot flag comes on later Evidence: ledger:E0297</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x224DE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB6" flags="0x0">
    <title>Coolant Hot Flag - Off Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant temperature below which the coolant-hot flag clears. Stock 122 C. Effect: keep below the On value Evidence: ledger:E0297</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x224DC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB7" flags="0x0">
    <title>Coolant Over-Temp Flag 2 - On Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Second, higher coolant over-temperature flag, also broadcast to other modules on the vehicle network. Stock 129 C. Effect: raise = second flag comes on later Evidence: ledger:E0297</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x224E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xB8" flags="0x0">
    <title>Coolant Over-Temp Flag 2 - Off Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant temperature below which the second over-temperature flag clears. Stock 126 C. Effect: keep below the On value Evidence: ledger:E0297</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x224E0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xB9" flags="0x30">
    <title>Cranking Spark vs RPM vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark advance used while cranking, by coolant (rows) and engine speed (columns). Stock 3 to 12 deg. Effect: more advance = can start faster but risks kickback; less = softer, slower starts Evidence: ledger:E0299</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="50" />
      <LABEL index="2" value="100" />
      <LABEL index="3" value="150" />
      <LABEL index="4" value="200" />
      <LABEL index="5" value="250" />
      <LABEL index="6" value="300" />
      <LABEL index="7" value="350" />
      <LABEL index="8" value="400" />
      <LABEL index="9" value="450" />
      <LABEL index="10" value="500" />
      <LABEL index="11" value="550" />
      <LABEL index="12" value="600" />
      <LABEL index="13" value="650" />
      <LABEL index="14" value="700" />
      <LABEL index="15" value="750" />
      <LABEL index="16" value="800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>10</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <LABEL index="9" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2D4BD" mmedelementsizebits="8" mmedrowcount="10" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xBA" flags="0x0">
    <title>LTFT Maximum Adjustment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest value a long-term fuel trim cell can learn. Stock 1.25 (+25 % fuel). Effect: raise = trims can add more fuel Evidence: ledger:E0300</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24AF8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBB" flags="0x0">
    <title>LTFT Minimum Adjustment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest value a long-term fuel trim cell can learn. Stock 0.60 (-40 % fuel). Effect: lower = trims can remove more fuel Evidence: ledger:E0300</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24AFA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBC" flags="0x0">
    <title>LTFT Idle Cell - Throttle Enter Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle trim cell is used when throttle is below this (and speed below its limit). Stock 0.10 %. Effect: raise = idle cell used with slightly open throttle Evidence: ledger:E0300</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24ADA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBD" flags="0x0">
    <title>LTFT Idle Cell - Throttle Leave Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle trim cell is left when throttle rises above this. Stock 0.20 %. Effect: keep above the enter value Evidence: ledger:E0300</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24AD8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBE" flags="0x0">
    <title>LTFT Idle Cell - Speed Enter Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle trim cell is used below this vehicle speed. Stock 3 km/h. Effect: raise = idle cell used while rolling slowly Evidence: ledger:E0300</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24ADE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xBF" flags="0x0">
    <title>LTFT Idle Cell - Speed Leave Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle trim cell is left above this vehicle speed. Stock 6 km/h. Effect: keep above the enter value Evidence: ledger:E0300</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24ADC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC0" flags="0x0">
    <title>Clear Flood - Throttle Enable Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While cranking, throttle above this switches cranking fuel to its clear-flood mode (for a flooded engine). Stock 90 %. Effect: lower = clear flood engages at less throttle Evidence: ledger:E0301</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26B9C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC1" flags="0x0">
    <title>Clear Flood - Throttle Disable Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Clear-flood mode ends when throttle falls below this. Stock 85 %. Effect: keep below the enable value Evidence: ledger:E0301</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26B9E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC2" flags="0x0">
    <title>Fuel Pump Prime Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the fuel pump runs to prime the system at key-on. Stock 2.0 s. Effect: raise = longer prime (helps a slow-starting pump or long lines) Evidence: ledger:E0302</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2989C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC3" flags="0x0">
    <title>Output Shaft Sensor Pulses Per Rev</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of pulses the transmission output-shaft speed sensor makes per shaft revolution. The PCM divides by it to turn sensor pulses into output-shaft rpm, which drives vehicle speed, the speedometer and every speed-based table. Stock H3 40. It describes the sensor hardware: change it only for a different reluctor, never to correct the speedometer (use axle ratio and tire revs for that) (E0303). Effect: output-shaft rpm and vehicle speed scale as 1 / value Evidence: ledger:E0303</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x3FB24" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>pulses/rev</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC4" flags="0x0">
    <title>PE Delay - Coolant Bypass Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Power enrichment is delayed only while coolant is at or above this; colder, PE comes in with no delay. Stock 0 C. Effect: raise = no PE delay over a wider cold range Evidence: ledger:E0307</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x295CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC5" flags="0x0">
    <title>PE Delay - Coolant Bypass Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Power enrichment is delayed only while coolant is at or below this; hotter, PE comes in with no delay. Stock 110 C. Effect: lower = no PE delay on a hot engine sooner Evidence: ledger:E0307</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x295D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC6" flags="0x0">
    <title>PE Delay - Throttle Rise Bypass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A throttle rise at least this big since the last update skips the PE delay, but only below the speed bypass value. Stock 10 %. Effect: lower = smaller stabs of throttle skip the delay Evidence: ledger:E0307</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x295D4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% per update</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC7" flags="0x0">
    <title>PE Delay - Speed Bypass Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this vehicle speed a fast throttle rise skips the PE delay (for full-throttle launches). At or above it the delay always applies. Stock 8 km/h. Effect: raise = throttle-stab bypass works at higher speeds Evidence: ledger:E0307</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x295D6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC8" flags="0x0">
    <title>Closed Loop Idle - Throttle Enter Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel switches to its idle settings (short-term trim steps, O2 switch point) when throttle is below this and speed is below its limit. Stock 0.10 %. Effect: raise = idle settings used with slightly open throttle Evidence: ledger:E0305</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E00" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xC9" flags="0x0">
    <title>Closed Loop Idle - Throttle Leave Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel leaves its idle settings when throttle reaches this. Stock 0.20 %. Effect: keep above the enter value Evidence: ledger:E0305</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24DFE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCA" flags="0x0">
    <title>Closed Loop Idle - Speed Enter Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel uses its idle settings below this vehicle speed. Stock 3 km/h. Effect: raise = idle settings used while rolling slowly Evidence: ledger:E0305</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E04" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCB" flags="0x0">
    <title>Closed Loop Idle - Speed Leave Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel leaves its idle settings at this vehicle speed. Stock 6 km/h. Effect: keep above the enter value Evidence: ledger:E0305</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E02" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xCC" flags="0x0">
    <title>DFCO Exit - RPM Drop per Update</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While in decel fuel cut, an engine speed fall of at least this much between two updates ends the cut (guards against stalling when rpm drops fast). Stock 300 rpm. Effect: lower = fuel returns on smaller rpm drops Evidence: ledger:E0308</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F184" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xCD" flags="0x30">
    <title>DFCO Exit - Minimum RPM vs Desired Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While in decel fuel cut, engine speed below this (looked up from the current desired idle) ends the cut. Stock 700 rpm at 800 rpm desired idle, 500 at 600. Effect: raise = fuel returns at a higher rpm (less chance of stalling, less fuel saved) Evidence: ledger:E0308</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1000" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1400" />
      <LABEL index="6" value="1600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F188" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xCE" flags="0x30">
    <title>LTFT Cell RPM Boundaries</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speeds that split the long-term fuel trim cells into 4 rpm columns (a column runs up to and including its boundary). Stock 100 / 6000 / 6500 rpm, so normal driving is all one column. Effect: spread these out to learn separate trims for different rpm bands (keep them rising) Evidence: ledger:E0310</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>boundary</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24AE6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xCF" flags="0x30">
    <title>LTFT Cell MAP Boundaries</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Manifold pressures that split the long-term fuel trim cells into 4 MAP rows. Stock 5 / 60 / 110 kPa, so normal driving uses two rows split at 60 kPa. Effect: move these to change which loads share a learned trim (keep them rising) Evidence: ledger:E0310</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>boundary</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24AEC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xD0" flags="0x0">
    <title>LTFT Cell RPM Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once in an LTFT cell, rpm must pass its boundaries by this much to change column. Stock 50 rpm. Effect: raise = fewer cell changes near a boundary Evidence: ledger:E0310</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24AE2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD1" flags="0x0">
    <title>LTFT Cell MAP Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once in a long-term fuel trim cell, manifold pressure must pass the cell&#x27;s row boundaries by this much before the trim moves to another row. Stock 2 kPa. Effect: raise = fewer cell changes near a boundary Evidence: ledger:E0310, ledger:E1369</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24AE4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD2" flags="0x0">
    <title>LTFT Learn Deadband</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short-term trim must be more than this far from 0 % before the long-term cell learns up or down. Stock 3.0 %. Effect: lower = long-term trims follow smaller errors (more hunting); higher = only larger errors are learned Evidence: ledger:E0311</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24B00" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xD3" flags="0x30">
    <title>LTFT Learn Minimum MAP vs Baro</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim only learns when MAP is at least this, looked up from barometric pressure. Stock 0 at every point: no limit. Effect: raise = long term trim does not learn below this manifold pressure Evidence: ledger:E0311, ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="65" />
      <LABEL index="1" value="70" />
      <LABEL index="2" value="75" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="85" />
      <LABEL index="5" value="90" />
      <LABEL index="6" value="95" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24B04" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD4" flags="0x30">
    <title>Transmission Gear Ratios (1st-4th)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM&#x27;s copy of the 4L60-E gear ratios (stock 3.06 / 1.63 / 1.00 / 0.70). Used to work out the transfer-case ratio for 4-Lo detection. Change only for a transmission with different ratios (E0337). A second copy at x2048 (Transmission Gear Ratios, second copy) feeds the torque estimate: change both (E0337). Effect: 4-Lo detection (transfer-case ratio) and any logic that divides by the current gear ratio Evidence: ledger:E0337</description>
    <CATEGORYMEM index="0" category="10" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3FB82" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>:1</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD5" flags="0x30">
    <title>Transient Fuel - Deposit Multiplier vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the wall deposit fraction by engine airflow. Stock 1.0 everywhere. Effect: below 1.0 = less wall-wetting compensation at that airflow Evidence: ledger:E0316</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="8" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="24" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="48" />
      <LABEL index="7" value="56" />
      <LABEL index="8" value="64" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="88" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="104" />
      <LABEL index="14" value="112" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="128" />
      <LABEL index="17" value="136" />
      <LABEL index="18" value="144" />
      <LABEL index="19" value="152" />
      <LABEL index="20" value="160" />
      <LABEL index="21" value="168" />
      <LABEL index="22" value="176" />
      <LABEL index="23" value="184" />
      <LABEL index="24" value="192" />
      <LABEL index="25" value="200" />
      <LABEL index="26" value="208" />
      <LABEL index="27" value="216" />
      <LABEL index="28" value="224" />
      <LABEL index="29" value="232" />
      <LABEL index="30" value="240" />
      <LABEL index="31" value="248" />
      <LABEL index="32" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x268E2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xD6" flags="0x30">
    <title>Transient Fuel - Tip-Out Correction Multiplier vs Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transient fuel, tip-out mode: while the mode is on (after a sudden MAP fall, until the throttle opens again or the wall film stops shrinking) the wall film fuel correction is multiplied by this, by port temperature. On a tip-out the correction removes fuel, so a larger value removes more. Stock 1.5 cold, 0.7 hot. Effect: raise = more fuel is taken out on a throttle lift Evidence: ledger:E0316, ledger:E1125</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (port temp model)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-24" />
      <LABEL index="2" value="-8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="24" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="56" />
      <LABEL index="7" value="72" />
      <LABEL index="8" value="88" />
      <LABEL index="9" value="104" />
      <LABEL index="10" value="120" />
      <LABEL index="11" value="136" />
      <LABEL index="12" value="152" />
      <LABEL index="13" value="168" />
      <LABEL index="14" value="184" />
      <LABEL index="15" value="200" />
      <LABEL index="16" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26674" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>3.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xD7" flags="0x0">
    <title>Transient Fuel - MAP Filter Coefficient</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transient fuel: how fast the filtered MAP follows real MAP. The tip-out mode is detected as MAP falling below this filtered value. Stock 0.20 of the gap per update. Effect: lower = slower filter, the tip-out mode is detected more easily and for longer Evidence: ledger:E0316, ledger:E1125</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26668" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD8" flags="0x0">
    <title>Transient Fuel - Tip-Out MAP Fall Trigger</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transient fuel, tip-out mode: the mode starts when manifold pressure is more than this below its filtered value, that is when MAP is falling fast. Stock 2.0 kPa. Effect: lower = the tip-out mode starts on smaller MAP drops Evidence: ledger:E0316, ledger:E1125</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2666C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xD9" flags="0x0">
    <title>Transient Fuel - Tip-Out End on Throttle Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transient fuel, tip-out mode: the mode ends when the throttle rises by more than this between updates. Stock 0 %: any opening of the throttle ends it. Effect: raise = the tip-out mode survives a small throttle opening Evidence: ledger:E0316, ledger:E1125</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2666E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>% per update</units>
    <decimalpl>3</decimalpl>
    <min>-200.000000</min>
    <max>199.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xDA" flags="0x30">
    <title>Injection Timing (main pulse) - Coolant Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. End-of-injection angle term for the main injection pulse by coolant, in crank degrees of the 720 degree cycle. The coolant term and the engine speed term are added and capped at 720 deg. Stock 514 deg at every coolant temperature. Effect: raise = main injection pulse ends later in the engine cycle Evidence: ledger:E0317, ledger:E1182</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25332" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg (crank, end of injection)</units>
      <decimalpl>2</decimalpl>
      <min>-1024.000000</min>
      <max>1023.968750</max>
      <MATH equation="X/32"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDB" flags="0x30">
    <title>Injection Timing (main pulse) - RPM Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. End-of-injection angle term for the main injection pulse by engine speed, in crank degrees of the 720 degree cycle. The coolant term and the engine speed term are added and capped at 720 deg. Stock 120 deg at 0 and 128 rpm, 90 deg at 256 rpm, 40 at 384, 20 at 512 and 0 from 640 rpm: it only acts while cranking. Effect: raise = main injection pulse ends later in the engine cycle Evidence: ledger:E0317, ledger:E1182</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="128" />
      <LABEL index="2" value="256" />
      <LABEL index="3" value="384" />
      <LABEL index="4" value="512" />
      <LABEL index="5" value="640" />
      <LABEL index="6" value="768" />
      <LABEL index="7" value="896" />
      <LABEL index="8" value="1024" />
      <LABEL index="9" value="1152" />
      <LABEL index="10" value="1280" />
      <LABEL index="11" value="1408" />
      <LABEL index="12" value="1536" />
      <LABEL index="13" value="1664" />
      <LABEL index="14" value="1792" />
      <LABEL index="15" value="1920" />
      <LABEL index="16" value="2048" />
      <LABEL index="17" value="2176" />
      <LABEL index="18" value="2304" />
      <LABEL index="19" value="2432" />
      <LABEL index="20" value="2560" />
      <LABEL index="21" value="2688" />
      <LABEL index="22" value="2816" />
      <LABEL index="23" value="2944" />
      <LABEL index="24" value="3072" />
      <LABEL index="25" value="3200" />
      <LABEL index="26" value="3328" />
      <LABEL index="27" value="3456" />
      <LABEL index="28" value="3584" />
      <LABEL index="29" value="3712" />
      <LABEL index="30" value="3840" />
      <LABEL index="31" value="3968" />
      <LABEL index="32" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25356" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg (crank, end of injection)</units>
      <decimalpl>2</decimalpl>
      <min>-1024.000000</min>
      <max>1023.968750</max>
      <MATH equation="X/32"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDC" flags="0x30">
    <title>Injection Timing (second pulse) - Coolant Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. End-of-injection angle term for the second injection pulse by coolant, in crank degrees of the 720 degree cycle. The coolant term and the engine speed term are added and capped at 720 deg. Stock 0 everywhere. Effect: raise = second injection pulse ends later in the engine cycle Evidence: ledger:E0317, ledger:E1182</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2539A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg (crank, end of injection)</units>
      <decimalpl>2</decimalpl>
      <min>-1024.000000</min>
      <max>1023.968750</max>
      <MATH equation="X/32"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xDD" flags="0x30">
    <title>Cranking Dwell Multiplier vs Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While cranking, the dwell from the base dwell table and modifier is multiplied by this, by battery voltage. Stock 1.0 everywhere. Effect: raise = longer coil charge while cranking (hotter spark, more coil heat) Evidence: ledger:E0318</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>22</indexcount>
      <units>V</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="4.5" />
      <LABEL index="1" value="5.5" />
      <LABEL index="2" value="6.5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="8.5" />
      <LABEL index="5" value="9.5" />
      <LABEL index="6" value="10.5" />
      <LABEL index="7" value="11.5" />
      <LABEL index="8" value="12.5" />
      <LABEL index="9" value="13.5" />
      <LABEL index="10" value="14.5" />
      <LABEL index="11" value="15.5" />
      <LABEL index="12" value="16.5" />
      <LABEL index="13" value="17.5" />
      <LABEL index="14" value="18.5" />
      <LABEL index="15" value="19.5" />
      <LABEL index="16" value="20.5" />
      <LABEL index="17" value="21.5" />
      <LABEL index="18" value="22.5" />
      <LABEL index="19" value="23.5" />
      <LABEL index="20" value="24.5" />
      <LABEL index="21" value="25.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F83E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="22" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xDE" flags="0x0">
    <title>Cranking Maximum Dwell Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While cranking, the maximum allowed dwell is the cranking dwell times this. Stock 1.20. Effect: sets how far cranking dwell may stretch or shrink Evidence: ledger:E0318</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2F86C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xDF" flags="0x0">
    <title>Cranking Minimum Dwell Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While cranking, the minimum dwell is the cranking dwell times this (further limited by the dwell ceiling). Stock 0.75. Effect: sets how far cranking dwell may stretch or shrink Evidence: ledger:E0318</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2F86A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE0" flags="0x0">
    <title>Final Drive Ratio - Transmission Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The transmission&#x27;s own copy of the axle ratio (stock 4.5555 = 41/9). Shift points and converter lockup use a vehicle speed computed from this and Tire Revs per Distance - Transmission Speed, not from Final Drive Ratio. After an axle or tire change set both pairs, or the speedometer will be right and the shift points off (E0319). Change it together with Final Drive Ratio and VSS Tire Revs per Distance: this pair is what shift points and converter lockup use. Code-proven, not yet confirmed on a drive. Effect: shift points and converter lockup speed (transmission-side vehicle speed) Evidence: ledger:E0319, ledger:E0808</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x3FB18" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>:1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE1" flags="0x0">
    <title>Tire Revs per Distance - Transmission Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The transmission&#x27;s own tire size (stored as revs/km x64). Stock 639.4 revs/mi, about 1.8 % more than the speedometer&#x27;s 627.6, so the transmission sees speed about 1.8 % lower than the dash. Shift points and converter lockup follow this value, not VSS Tire Revs per Distance. Set both after a tire change (E0319). Change it together with Final Drive Ratio and VSS Tire Revs per Distance: this pair is what shift points and converter lockup use. Code-proven, not yet confirmed on a drive. Effect: shift points and converter lockup speed (transmission-side vehicle speed) Evidence: ledger:E0319, ledger:E0808</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x3FB3A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>revs/mi</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>1647.943110</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*0.02514600"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE2" flags="0x0">
    <title>Idle Speed Control - A/C Airflow Offset Ramp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the A/C is requested, the idle speed controller&#x27;s airflow limits are raised toward the A/C idle air term by this much per update. Stock 0.10 g/s. Effect: raise = limits follow the A/C air sooner Evidence: ledger:E0322</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x22076" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s per update</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE3" flags="0x30">
    <title>Idle Speed Control - Controller Coefficients (In Gear) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Eight coefficients of the idle speed controller used in gear (stock identical to the Park / Neutral set). Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (idle speed controller) Evidence: ledger:E0322, ledger:E0899</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>coefficient</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22078" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE4" flags="0x30">
    <title>Idle Speed Control - Controller Coefficients (Park / Neutral) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Eight coefficients of the idle speed controller used in Park / Neutral (stock identical to the in-gear set). Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (idle speed controller) Evidence: ledger:E0322, ledger:E0899</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>coefficient</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22088" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xE5" flags="0x0">
    <title>RPM Control - Minimum Target RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The rpm controller&#x27;s target is the desired idle or this, whichever is higher. Stock 900 rpm. Effect: raise = higher minimum target Evidence: ledger:E0325</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22EEC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xE6" flags="0x0">
    <title>RPM Control - Maximum Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The rpm controller only runs below this vehicle speed. Stock 10 km/h. Effect: raise = runs at higher speeds Evidence: ledger:E0325</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22F00" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xE7" flags="0x30">
    <title>Pedal Throttle Area - Rise Rate Limit vs RPM by Trans State</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most the pedal throttle-area demand may increase per update, by transmission state (rows) and rpm (columns). Softens tip-in. Rows: 0 to 3 = 1st to 4th gear (4 and 5 unused on the 4-speed), 6 = Neutral, 7 = Reverse, 8 = Park. Effect: raise = sharper throttle response on tip-in Evidence: ledger:E0330, ledger:E1329</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>8</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 7" />
      <LABEL index="1" value="state 0 (1st)" />
      <LABEL index="2" value="state 1 (2nd)" />
      <LABEL index="3" value="state 2 (3rd)" />
      <LABEL index="4" value="state 3 (4th)" />
      <LABEL index="5" value="state 4" />
      <LABEL index="6" value="state 5" />
      <LABEL index="7" value="other (P / N)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23E82" mmedelementsizebits="16" mmedrowcount="8" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% area per update</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE8" flags="0x30">
    <title>Pedal Throttle Area - Fall Rate Limit vs RPM by Trans State</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most the pedal throttle-area demand may decrease per update, by transmission state (rows) and rpm (columns). Softens tip-out. Rows: 0 to 3 = 1st to 4th gear (4 and 5 unused on the 4-speed), 6 = Neutral, 7 = Reverse, 8 = Park. Effect: raise = throttle closes faster on tip-out Evidence: ledger:E0330, ledger:E1329</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>8</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 7" />
      <LABEL index="1" value="state 0 (1st)" />
      <LABEL index="2" value="state 1 (2nd)" />
      <LABEL index="3" value="state 2 (3rd)" />
      <LABEL index="4" value="state 3 (4th)" />
      <LABEL index="5" value="state 4" />
      <LABEL index="6" value="state 5" />
      <LABEL index="7" value="other (P / N)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23E22" mmedelementsizebits="16" mmedrowcount="8" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% area per update</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xE9" flags="0x30">
    <title>ETC Torque Control - Gain Switch Torque by Trans State</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. INACTIVE on the stock H3: the controller only runs when an enable = 1 (stock 0). Engine torque at which the throttle torque controller switches from its low-torque to its high-torque gains, per transmission state. Stock 150 / 140 / 135 / 120 Nm for states 0 to 3, 100 Nm above. Effect: raise = low-torque gains used up to higher torque Evidence: ledger:E0333, ledger:E0341</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20576" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>16383.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xEA" flags="0x0">
    <title>ETC Torque Control - Gain Switch Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. INACTIVE on the stock H3: the controller only runs when an enable = 1 (stock 0). Once on the high-torque gains, the switch torque is lowered by half of this. Stock 10 Nm (5 Nm effective). Effect: raise = less switching back and forth Evidence: ledger:E0333, ledger:E0341</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20570" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>16383.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0xEB" flags="0x30">
    <title>ETC Torque Control - Input Gain (high torque) vs RPM by Trans State</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, high engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): the controller&#x27;s input is multiplied by this (1.0 = unchanged). 1.0 = 65536 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:E0390, ledger:E1149</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2058C" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xEC" flags="0x30">
    <title>ETC Torque Control - Output Feedback Gain (high torque) vs RPM by Trans State</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, high engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): share of the controller&#x27;s previous output carried into the new output each update. 1.0 = 65536 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2081C" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xED" flags="0x30">
    <title>ETC Torque Control - Previous Input Weight (high torque) vs RPM by Trans State</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, high engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): weight of the previous scaled input in the new output (signed). 1.0 = 8192 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:E0390, ledger:E1149</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20AAC" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>-4.000000</min>
      <max>3.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xEE" flags="0x30">
    <title>ETC Torque Control - Current Input Weight (high torque) vs RPM by Trans State</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, high engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): weight of the current scaled input in the new output (signed). 1.0 = 8192 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:E0390, ledger:E1149</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20D3C" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>-4.000000</min>
      <max>3.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xEF" flags="0x30">
    <title>ETC Torque Control - Input Gain (low torque) vs RPM by Trans State</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, low engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): the controller&#x27;s input is multiplied by this (1.0 = unchanged). 1.0 = 65536 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:E0390, ledger:E1149</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x206D4" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xF0" flags="0x30">
    <title>ETC Torque Control - Output Feedback Gain (low torque) vs RPM by Trans State</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, low engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): share of the controller&#x27;s previous output carried into the new output each update. 1.0 = 65536 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:E...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20964" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xF1" flags="0x30">
    <title>ETC Torque Control - Previous Input Weight (low torque) vs RPM by Trans State</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, low engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): weight of the previous scaled input in the new output (signed). 1.0 = 8192 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:E0390, ledger:E1149</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20BF4" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>-4.000000</min>
      <max>3.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xF2" flags="0x30">
    <title>ETC Torque Control - Current Input Weight (low torque) vs RPM by Trans State</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle torque controller, low engine torque set (chosen by the gain switch torque), by transmission state (rows) and engine speed (columns, 0 to 8000 rpm): weight of the current scaled input in the new output (signed). 1.0 = 8192 raw. The controller is switched off on this calibration (its enable is 0), so this table is never used. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0333, ledger:E0341, ledger:E0390, ledger:E1149</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="state 6" />
      <LABEL index="7" value="state 7" />
      <LABEL index="8" value="state 8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20E84" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>-4.000000</min>
      <max>3.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xF3" flags="0x30">
    <title>Tip-In Torque Mgmt - Minimum Speed by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only, closed-throttle tip-ins): active only above this vehicle speed. Stock 5 km/h. Effect: widens or narrows the speed range where tip-ins are softened Evidence: ledger:E0346</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2102C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0xF4" flags="0x30">
    <title>Tip-In Torque Mgmt - Maximum Speed by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only, closed-throttle tip-ins): active only below this vehicle speed. Stock 64 km/h. Effect: widens or narrows the speed range where tip-ins are softened Evidence: ledger:E0346</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21020" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0xF5" flags="0x0">
    <title>Tip-In Torque Mgmt - Closed Throttle Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only, closed-throttle tip-ins): throttle counts as closed below this. Stock 0.38 %. Effect: raise = counts as closed with slightly open throttle Evidence: ledger:E0346</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21050" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xF6" flags="0x0">
    <title>Tip-In Torque Mgmt - Closed Throttle Ends Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only, closed-throttle tip-ins): the closed-throttle flag clears at this. Stock 0.47 %. Effect: keep above the closed value Evidence: ledger:E0346</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2104E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xF7" flags="0x0">
    <title>Tip-In Torque Mgmt - Minimum Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only, closed-throttle tip-ins): only above this coolant temperature. Stock 75 C. Effect: lower = also when colder Evidence: ledger:E0346</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21052" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xF8" flags="0x0">
    <title>Idle Airflow Learn - Saved Value Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. Upper clamp applied when the learn is written to keep-alive memory. Stock 3.5 g/s. Effect: raise = a larger learned value survives key-off Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29CBA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xF9" flags="0x0">
    <title>Idle Airflow Learn - Saved Value Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. Lower clamp applied when the learn is written to keep-alive memory. Stock -1.0 g/s. Effect: lower = a more negative learned value survives key-off Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29CBC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xFA" flags="0x0">
    <title>Altitude/Cold Idle-Up - Hold Maximum Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up flare and altitude idle-up gating. The altitude/cold idle-up (stock amount 0) is held while vehicle speed is below this. Stock 8 km/h. Effect: affects only a non-zero idle-up amount Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B0B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xFB" flags="0x0">
    <title>Altitude/Cold Idle-Up - Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up flare and altitude idle-up gating. How long the altitude/cold idle-up is held (timer in 1/20 s). Stock 30 s. Effect: raise = idle-up lasts longer Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B0B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xFC" flags="0x0">
    <title>Altitude/Cold Idle-Up - Baro Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up flare and altitude idle-up gating. The idle-up applies when barometric pressure is below this. Stock 80 kPa. Effect: raise = applies at lower altitude Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B0A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xFD" flags="0x0">
    <title>Start-Up RPM Flare - Cancel After Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up flare and altitude idle-up gating. After this run time the start-up flare is cancelled as soon as the truck moves or the throttle opens. Stock 8 s. Effect: raise = the flare survives an early drive-away longer Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B0B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xFE" flags="0x0">
    <title>Start-Up RPM Flare - Cancel Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up flare and altitude idle-up gating. Vehicle speed above which the flare is cancelled (after the cancel run time). Stock 30 km/h. Effect: raise = flare kept to a higher speed Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B0B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0xFF" flags="0x0">
    <title>Start-Up RPM Flare - Cancel Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up flare and altitude idle-up gating. Throttle above which the flare is cancelled (after the cancel run time). Stock 5 %. Effect: raise = flare kept with more throttle Evidence: ledger:E0347</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B0A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x100" flags="0x0">
    <title>Idle RPM-Control Mode - Maximum Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle rpm-control mode entry. The mode is only entered below this vehicle speed (plus the hysteresis once active). Stock 17.5 km/h. Effect: raise = mode entered at higher speed Evidence: ledger:E0347, ledger:E0429, ledger:E0441</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A220" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x101" flags="0x0">
    <title>Idle RPM-Control Mode - Speed Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle rpm-control mode entry. Added to the maximum speed while the mode is active. Stock 2 km/h. Effect: raise = mode held to a higher speed Evidence: ledger:E0347, ledger:E0429, ledger:E0441</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A22A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x102" flags="0x0">
    <title>Idle RPM-Control Mode - Entry Delay (rpm at/above desired)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle rpm-control mode entry. Time since the throttle closed before the mode is entered, when rpm is at or above desired. Stock 0.75 s. Effect: raise = later entry after a lift Evidence: ledger:E0347, ledger:E0429, ledger:E0441</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A22C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x103" flags="0x0">
    <title>Idle RPM-Control Mode - Entry Delay (rpm below desired)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle rpm-control mode entry. As above when rpm is below desired. Stock 0.0125 s. Effect: raise = later entry when rpm sags Evidence: ledger:E0347, ledger:E0429, ledger:E0441</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A22E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x104" flags="0x30">
    <title>Tip-In Torque Mgmt - Starting Torque by Range and Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): the tip-in torque limit starts from the current engine torque or this, whichever is higher, by forward range (rows) and gear (columns). Stock 0 / 5 / 10 / 20 / 20 / 20 Nm in every range. Effect: raise = tip-ins start from more torque (less softening) Evidence: ledger:E0356</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>trans state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="state 0" />
      <LABEL index="1" value="state 1" />
      <LABEL index="2" value="state 2" />
      <LABEL index="3" value="state 3" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>forward range</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="range 0" />
      <LABEL index="1" value="range 1" />
      <LABEL index="2" value="range 2" />
      <LABEL index="3" value="range 3" />
      <LABEL index="4" value="range 4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20FE4" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x105" flags="0x0">
    <title>Tip-In Torque Mgmt - Arm Below Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): a tip-in can only be armed while engine torque is below this. Stock 50 Nm. Effect: raise = arms at higher coast torque Evidence: ledger:E0356</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21038" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x106" flags="0x0">
    <title>Tip-In Torque Mgmt - Cancel Above Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): the tip-in limit is cancelled once engine torque is above this. Stock 100 Nm. Effect: raise = limit stays on to higher torque Evidence: ledger:E0356</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2103A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x107" flags="0x0">
    <title>Tip-In Torque Mgmt - Ramp End Margin</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): the torque ramp counts as complete once it has climbed this far above its starting torque. Stock 130 Nm. Effect: raise = longer ramp Evidence: ledger:E0356</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2103E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x108" flags="0x30">
    <title>Tip-In Torque Ramp - Fast Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up by a step each update. The step is the default step normally, the slow lash step while the driveline is taking up slack (gearbox slip above about 10 rpm, or engine speed rising faster than the slip-based limit), and the fast step once the limit has passed its target. This is the fast step, by throttle. Effect: raise = the torque limit catches up faster at the end of a tip-in Evidence: ledger:E0356, ledger:E0395, ledger:E0845</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% throttle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2106C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm per update</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x109" flags="0x30">
    <title>Tip-In Torque Ramp - Lash Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up by a step each update. The step is the default step normally, the slow lash step while the driveline is taking up slack (gearbox slip above about 10 rpm, or engine speed rising faster than the slip-based limit), and the fast step once the limit has passed its target. This is the lash step, by throttle, before the engine speed factor is applied (the step used is this value times the factor). Effect: raise = torque builds faster while the driveline takes up slack (more clunk) Evidence: ledger:E0356, ledger:E0395, ledger:E0845</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% throttle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21090" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm per update</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x10A" flags="0x30">
    <title>Tip-In Torque Ramp - Default Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up by a step each update. The step is the default step normally, the slow lash step while the driveline is taking up slack (gearbox slip above about 10 rpm, or engine speed rising faster than the slip-based limit), and the fast step once the limit has passed its target. This is the default step, by throttle. Effect: raise = faster torque build-up after a tip-in Evidence: ledger:E0356, ledger:E0395, ledger:E0845</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% throttle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x210B4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm per update</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x10B" flags="0x30">
    <title>Tip-In Torque Ramp - Lash Step Engine Speed Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up by a step each update. The step is the default step normally, the slow lash step while the driveline is taking up slack (gearbox slip above about 10 rpm, or engine speed rising faster than the slip-based limit), and the fast step once the limit has passed its target. Multiplies the lash step, by engine speed. Stock about 0.10 to 0.14. Effect: raise = larger lash step at that engine speed Evidence: ledger:E0356, ledger:E0395, ledger:E0845</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1600" />
      <LABEL index="3" value="2400" />
      <LABEL index="4" value="3200" />
      <LABEL index="5" value="4000" />
      <LABEL index="6" value="4800" />
      <LABEL index="7" value="5600" />
      <LABEL index="8" value="6400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21058" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>-8.000000</min>
      <max>7.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x10C" flags="0x30">
    <title>Tip-In Torque Ramp - Engine Speed Rise Limit vs Slip</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up by a step each update. The step is the default step normally, the slow lash step while the driveline is taking up slack (gearbox slip above about 10 rpm, or engine speed rising faster than the slip-based limit), and the fast step once the limit has passed its target. If engine speed rises faster than this per update at the current gearbox slip, the lash step is used. Stock 90 rpm per update at negative slip, tapering to 0 by 50 rpm. Effect: lower = the lash step engages on smaller engine speed flares Evidence: ledger:E0356, ledger:E03...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (gearbox slip)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-750" />
      <LABEL index="1" value="-700" />
      <LABEL index="2" value="-650" />
      <LABEL index="3" value="-600" />
      <LABEL index="4" value="-550" />
      <LABEL index="5" value="-500" />
      <LABEL index="6" value="-450" />
      <LABEL index="7" value="-400" />
      <LABEL index="8" value="-350" />
      <LABEL index="9" value="-300" />
      <LABEL index="10" value="-250" />
      <LABEL index="11" value="-200" />
      <LABEL index="12" value="-150" />
      <LABEL index="13" value="-100" />
      <LABEL index="14" value="-50" />
      <LABEL index="15" value="0" />
      <LABEL index="16" value="50" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x210D8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm per update</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x10D" flags="0x30">
    <title>Tip-In Torque Mgmt - Input Speed Rate Threshold (rise)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. Shunt detection: transmission input speed rising faster than this per update, by input speed, marks a driveline shunt. Stock 16 to 40 rpm per update. Effect: lower = shunt / swing-back detected sooner, so the fast step comes in sooner Evidence: ledger:E0356, ledger:E0689, ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.1" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1599.9" />
      <LABEL index="3" value="2399.8" />
      <LABEL index="4" value="3199.7" />
      <LABEL index="5" value="3999.6" />
      <LABEL index="6" value="4799.5" />
      <LABEL index="7" value="5599.4" />
      <LABEL index="8" value="6399.3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x210FC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm per update</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x10E" flags="0x30">
    <title>Tip-In Torque Mgmt - Input Speed Rate Threshold (fall)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. Swing-back detection: after a shunt, input speed falling faster than this per update, by input speed, marks the swing back. Stock -20 to -70 rpm per update. Effect: closer to zero = swing-back detected sooner Evidence: ledger:E0356, ledger:E0689, ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.1" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1599.9" />
      <LABEL index="3" value="2399.8" />
      <LABEL index="4" value="3199.7" />
      <LABEL index="5" value="3999.6" />
      <LABEL index="6" value="4799.5" />
      <LABEL index="7" value="5599.4" />
      <LABEL index="8" value="6399.3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21110" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm per update</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x10F" flags="0x30">
    <title>Tip-In Torque Mgmt - Vehicle Speed Rate Threshold (rise)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. Shunt detection on vehicle speed change per update, by vehicle speed. Stock off (maximum value). Effect: lower = shunt / swing-back detected sooner, so the fast step comes in sooner Evidence: ledger:E0356, ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21124" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per update</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x110" flags="0x30">
    <title>Tip-In Torque Mgmt - Vehicle Speed Rate Threshold (fall)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. Swing-back detection on vehicle speed change per update, by vehicle speed. Stock off (minimum value). Effect: closer to zero = swing-back detected sooner Evidence: ledger:E0356, ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21138" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per update</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x111" flags="0x30">
    <title>Knock Detection - Threshold Gain, Slot 1</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection (safety relevant). Threshold gain for knock loop slot 1 (the slot is the position in the knock module&#x27;s per-cylinder loop), by airmass (rows) and rpm (columns). The knock threshold is the background level plus this gain times the knock noise deviation, so 1.0 means one noise deviation above background. Stock 2.50 to 3.50. Raising it makes knock detection less sensitive. Effect: raise = a stronger knock signal is needed before knock retard (less sensitive) Evidence: ledger:E0364, ledger:E0703</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="500" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1500" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2500" />
      <LABEL index="6" value="3000" />
      <LABEL index="7" value="3500" />
      <LABEL index="8" value="4000" />
      <LABEL index="9" value="4500" />
      <LABEL index="10" value="5000" />
      <LABEL index="11" value="5500" />
      <LABEL index="12" value="6000" />
      <LABEL index="13" value="6500" />
      <LABEL index="14" value="7000" />
      <LABEL index="15" value="7500" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>g/cyl (airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.24" />
      <LABEL index="1" value="0.3" />
      <LABEL index="2" value="0.36" />
      <LABEL index="3" value="0.42" />
      <LABEL index="4" value="0.48" />
      <LABEL index="5" value="0.54" />
      <LABEL index="6" value="0.6" />
      <LABEL index="7" value="0.66" />
      <LABEL index="8" value="0.72" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31FC8" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain (x knock noise)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>127.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x112" flags="0x30">
    <title>Knock Detection - Threshold Gain Factor vs Commanded EQ</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection (safety relevant). Multiplies every slot&#x27;s threshold gain by the commanded equivalence ratio. Stock 1.00 at EQ 1.00 rising to 1.35 from EQ 1.34 (richer = less sensitive). Effect: raise = less knock sensitivity when running rich Evidence: ledger:E0364</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>EQ ratio</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="1.056" />
      <LABEL index="2" value="1.113" />
      <LABEL index="3" value="1.169" />
      <LABEL index="4" value="1.225" />
      <LABEL index="5" value="1.281" />
      <LABEL index="6" value="1.337" />
      <LABEL index="7" value="1.394" />
      <LABEL index="8" value="1.45" />
      <LABEL index="9" value="1.506" />
      <LABEL index="10" value="1.562" />
      <LABEL index="11" value="1.619" />
      <LABEL index="12" value="1.675" />
      <LABEL index="13" value="1.731" />
      <LABEL index="14" value="1.788" />
      <LABEL index="15" value="1.844" />
      <LABEL index="16" value="1.9" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3272E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x113" flags="0x30">
    <title>Knock Detection - Transient Threshold Adder vs RPM (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection (safety relevant). Added to the threshold gain while a transient (rpm, throttle or airmass change) is active. All zero on the stock H3, so it has no effect as delivered. Effect: raise = less knock sensitivity during transients Evidence: ledger:E0364, ledger:E0703</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="500" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1500" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2500" />
      <LABEL index="6" value="3000" />
      <LABEL index="7" value="3500" />
      <LABEL index="8" value="4000" />
      <LABEL index="9" value="4500" />
      <LABEL index="10" value="5000" />
      <LABEL index="11" value="5500" />
      <LABEL index="12" value="6000" />
      <LABEL index="13" value="6500" />
      <LABEL index="14" value="7000" />
      <LABEL index="15" value="7500" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3270A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain (x knock noise)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>127.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x114" flags="0x0">
    <title>Knock Detection - Transient Trigger, Engine Speed Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: while a transient is flagged the noise level tracking uses its transient settings and the knock threshold learn is paused. A rising transient is flagged when engine speed has risen by at least this across the 40 sample speed history. Stock 50 rpm. Effect: raise = fewer accelerations are treated as a transient Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31E46" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x115" flags="0x0">
    <title>Knock Detection - Transient Trigger, Engine Speed Fall</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: while a transient is flagged the noise level tracking uses its transient settings and the knock threshold learn is paused. A falling transient is flagged when engine speed has changed by this or less (a fall) across the 40 sample speed history. Stock -50 rpm. Effect: more negative = fewer decelerations are treated as a transient Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31E48" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x116" flags="0x0">
    <title>Knock Detection - Transient Trigger, Throttle Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: while a transient is flagged the noise level tracking uses its transient settings and the knock threshold learn is paused. A rising transient is flagged when the throttle has opened by at least this across the 5 sample throttle history. Stock 15 %. Effect: raise = fewer throttle openings are treated as a transient Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31E4A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>-200.000000</min>
    <max>199.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x117" flags="0x0">
    <title>Knock Detection - Transient Trigger, Throttle Fall</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: while a transient is flagged the noise level tracking uses its transient settings and the knock threshold learn is paused. A falling transient is flagged when the throttle has changed by this or less (closing) across the 5 sample throttle history. Stock -15 %. Effect: more negative = fewer throttle closings are treated as a transient Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31E4C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>-200.000000</min>
    <max>199.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x118" flags="0x0">
    <title>Knock Detection - Transient Trigger, Airmass Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: while a transient is flagged the noise level tracking uses its transient settings and the knock threshold learn is paused. A transient is flagged when the cylinder airmass differs from its filtered value by at least this, in either direction. Stock 0.0009 g per cylinder. Effect: raise = fewer load changes are treated as a transient Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31E4E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/cyl</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.095937</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x119" flags="0x30">
    <title>Knock Sensing Window Position vs RPM x Airmass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Where the knock sensing window sits, in crank degrees counted from each cylinder&#x27;s reference tooth on the crank wheel, by engine speed (columns) and cylinder airmass (rows). The PCM converts it to whole teeth plus a fraction of a tooth for the knock window hardware; the window length is the separate curve vs engine speed. Stock 0 deg at 0.24 g/cyl, 4 deg at 0.30 g/cyl, then 8.7 to 35.1 deg (falling with engine speed). Effect: do not edit: moves the crank angle where the knock sensor is listened to; a wrong window can hide real knock Evidence: ledger:E0367, ledger:E1180</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="500" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1500" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2500" />
      <LABEL index="6" value="3000" />
      <LABEL index="7" value="3500" />
      <LABEL index="8" value="4000" />
      <LABEL index="9" value="4500" />
      <LABEL index="10" value="5000" />
      <LABEL index="11" value="5500" />
      <LABEL index="12" value="6000" />
      <LABEL index="13" value="6500" />
      <LABEL index="14" value="7000" />
      <LABEL index="15" value="7500" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>g/cyl (filtered airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.24" />
      <LABEL index="1" value="0.3" />
      <LABEL index="2" value="0.36" />
      <LABEL index="3" value="0.42" />
      <LABEL index="4" value="0.48" />
      <LABEL index="5" value="0.54" />
      <LABEL index="6" value="0.6" />
      <LABEL index="7" value="0.66" />
      <LABEL index="8" value="0.72" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31E68" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>deg (crank, from cylinder reference tooth)</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1023.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x11A" flags="0x30">
    <title>Start-Up Fuel - Multiplier vs Events Still To Come</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start-up fuel events (one-shot pulses written for the first cylinder events at start-up). Multiplies each start-up pulse; index = events still to come after this one (the last event uses index 0). Stock 1.0 for 0 to 5 (only 0 to 3 used with the stock event counts), then 0.9 at 6 and 7, 0.8 at 8 and 9, 0.7 at 10 and 11, 0.6 at 12 and 13, 0.5 at 14 and 15. Event counts above 16 are not usable: the per-event trim lookup runs out of its table. Effect: raise = richer start-up pulses Evidence: ledger:E0369, ledger:E1183</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>16</indexcount>
      <units>events to come</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24678" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x11B" flags="0x30">
    <title>Throttle Actuator Servo Gains vs Battery Voltage (raw, DO NOT EDIT)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Five gains of the electronic throttle&#x27;s position servo (rows) by battery voltage, 2 to 18 V (columns). Values are the servo&#x27;s internal gain counts, shown raw. Not a tuning item. DO NOT EDIT. Effect: DO NOT EDIT Evidence: ledger:E0371, ledger:E0899, ledger:E1151, ledger:E1408</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>gain</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="Gain 1" />
      <LABEL index="1" value="Gain 2" />
      <LABEL index="2" value="Gain 3" />
      <LABEL index="3" value="Gain 4" />
      <LABEL index="4" value="Gain 5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22E38" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x11C" flags="0x30">
    <title>EVAP Leak Test Vacuum Decay Limit - Low Range</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP leak test, vacuum hold phase: the PCM seals the EVAP system under vacuum and measures how fast tank vacuum decays (the decay slope it reports on PID 1296). A slope above this limit fails the test. Rows cover the lower half of the EVAP vapour reference, which the PCM derives from fuel level (the row labels give the fuel level on stock settings, n/a = not reached); columns are intake air temperature 0 to 40 C. Stock 0.039 inH2O per second in every cell. Raising it lets a faster leak pass. Not used by the stock calibration: this belongs to the engine-running small leak phase, which the stock calibration switches off (small...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC (IAT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1.25" />
      <LABEL index="2" value="2.5" />
      <LABEL index="3" value="3.75" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6.25" />
      <LABEL index="6" value="7.5" />
      <LABEL index="7" value="8.75" />
      <LABEL index="8" value="10" />
      <LABEL index="9" value="11.25" />
      <LABEL index="10" value="12.5" />
      <LABEL index="11" value="13.75" />
      <LABEL index="12" value="15" />
      <LABEL index="13" value="16.25" />
      <LABEL index="14" value="17.5" />
      <LABEL index="15" value="18.75" />
      <LABEL index="16" value="20" />
      <LABEL index="17" value="21.25" />
      <LABEL index="18" value="22.5" />
      <LABEL index="19" value="23.75" />
      <LABEL index="20" value="25" />
      <LABEL index="21" value="26.25" />
      <LABEL index="22" value="27.5" />
      <LABEL index="23" value="28.75" />
      <LABEL index="24" value="30" />
      <LABEL index="25" value="31.25" />
      <LABEL index="26" value="32.5" />
      <LABEL index="27" value="33.75" />
      <LABEL index="28" value="35" />
      <LABEL index="29" value="36.25" />
      <LABEL index="30" value="37.5" />
      <LABEL index="31" value="38.75" />
      <LABEL index="32" value="40" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>% fuel level (stock settings)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="n/a" />
      <LABEL index="1" value="95" />
      <LABEL index="2" value="77" />
      <LABEL index="3" value="59" />
      <LABEL index="4" value="41" />
      <LABEL index="5" value="23" />
      <LABEL index="6" value="4" />
      <LABEL index="7" value="n/a" />
      <LABEL index="8" value="n/a" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x373AE" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>inH2O/s</units>
      <decimalpl>3</decimalpl>
      <min>-8.000000</min>
      <max>7.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x11D" flags="0x30">
    <title>EVAP Leak Test Vacuum Decay Limit - High Range</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP leak test, vacuum hold phase: the PCM seals the EVAP system under vacuum and measures how fast tank vacuum decays (the decay slope it reports on PID 1296). A slope above this limit fails the test. Rows cover the upper half of the EVAP vapour reference, which the PCM derives from fuel level (the row labels give the fuel level on stock settings, n/a = not reached); columns are intake air temperature 0 to 40 C. Stock 0.039 inH2O per second in every cell. Raising it lets a faster leak pass. Not used by the stock calibration: this belongs to the engine-running small leak phase, which the stock calibration switches off (small...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC (IAT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1.25" />
      <LABEL index="2" value="2.5" />
      <LABEL index="3" value="3.75" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6.25" />
      <LABEL index="6" value="7.5" />
      <LABEL index="7" value="8.75" />
      <LABEL index="8" value="10" />
      <LABEL index="9" value="11.25" />
      <LABEL index="10" value="12.5" />
      <LABEL index="11" value="13.75" />
      <LABEL index="12" value="15" />
      <LABEL index="13" value="16.25" />
      <LABEL index="14" value="17.5" />
      <LABEL index="15" value="18.75" />
      <LABEL index="16" value="20" />
      <LABEL index="17" value="21.25" />
      <LABEL index="18" value="22.5" />
      <LABEL index="19" value="23.75" />
      <LABEL index="20" value="25" />
      <LABEL index="21" value="26.25" />
      <LABEL index="22" value="27.5" />
      <LABEL index="23" value="28.75" />
      <LABEL index="24" value="30" />
      <LABEL index="25" value="31.25" />
      <LABEL index="26" value="32.5" />
      <LABEL index="27" value="33.75" />
      <LABEL index="28" value="35" />
      <LABEL index="29" value="36.25" />
      <LABEL index="30" value="37.5" />
      <LABEL index="31" value="38.75" />
      <LABEL index="32" value="40" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>% fuel level (stock settings)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="n/a" />
      <LABEL index="1" value="n/a" />
      <LABEL index="2" value="n/a" />
      <LABEL index="3" value="n/a" />
      <LABEL index="4" value="n/a" />
      <LABEL index="5" value="n/a" />
      <LABEL index="6" value="n/a" />
      <LABEL index="7" value="n/a" />
      <LABEL index="8" value="n/a" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37606" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>inH2O/s</units>
      <decimalpl>3</decimalpl>
      <min>-8.000000</min>
      <max>7.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x11E" flags="0x30">
    <title>Exhaust Temperature Model - Power-Up Restore vs Engine-Off Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At power-up the catalyst channel of the exhaust temperature model restarts from the modelled temperature it held at shutdown (rows), decayed by how long the engine was off (columns, 0 to 9600 s in 5 minute steps); the other two channels restart at 0. Column 0 returns the row temperature and every row decays toward 0 with a time constant of about 33 minutes. The model is read only by diagnostics (catalyst monitor conditions, a diagnostic timer and secondary air), not by fuel, spark, torque or throttle. If the engine-off timer has failed its own check (P2610), the engine-off time is taken as 0, so the shutdown temperature is re...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>s (engine-off time)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="300" />
      <LABEL index="2" value="600" />
      <LABEL index="3" value="900" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1500" />
      <LABEL index="6" value="1800" />
      <LABEL index="7" value="2100" />
      <LABEL index="8" value="2400" />
      <LABEL index="9" value="2700" />
      <LABEL index="10" value="3000" />
      <LABEL index="11" value="3300" />
      <LABEL index="12" value="3600" />
      <LABEL index="13" value="3900" />
      <LABEL index="14" value="4200" />
      <LABEL index="15" value="4500" />
      <LABEL index="16" value="4800" />
      <LABEL index="17" value="5100" />
      <LABEL index="18" value="5400" />
      <LABEL index="19" value="5700" />
      <LABEL index="20" value="6000" />
      <LABEL index="21" value="6300" />
      <LABEL index="22" value="6600" />
      <LABEL index="23" value="6900" />
      <LABEL index="24" value="7200" />
      <LABEL index="25" value="7500" />
      <LABEL index="26" value="7800" />
      <LABEL index="27" value="8100" />
      <LABEL index="28" value="8400" />
      <LABEL index="29" value="8700" />
      <LABEL index="30" value="9000" />
      <LABEL index="31" value="9300" />
      <LABEL index="32" value="9600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC (modelled catalyst temperature at shutdown)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="200" />
      <LABEL index="1" value="250" />
      <LABEL index="2" value="300" />
      <LABEL index="3" value="350" />
      <LABEL index="4" value="400" />
      <LABEL index="5" value="450" />
      <LABEL index="6" value="500" />
      <LABEL index="7" value="550" />
      <LABEL index="8" value="600" />
      <LABEL index="9" value="650" />
      <LABEL index="10" value="700" />
      <LABEL index="11" value="750" />
      <LABEL index="12" value="800" />
      <LABEL index="13" value="850" />
      <LABEL index="14" value="900" />
      <LABEL index="15" value="950" />
      <LABEL index="16" value="1000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x352EA" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1023.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x11F" flags="0x30">
    <title>Engine Torque Estimate - RPM Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stored rpm breakpoints of the throttle-based torque estimate table: 0 to 7680 rpm in 512 rpm steps, then 8191. Effect: moves the axis of every table that uses it: edit with care Evidence: ledger:E0377</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31024" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x120" flags="0x30">
    <title>Engine Torque Estimate - Throttle Breakpoints (raw, DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle breakpoints of the throttle-based engine torque estimate table: 33 stored points, non-uniform from 0, then an end marker. The torque estimate feeds shift pressure, torque reduction, converter clutch and throttle torque control. Shown raw. DO NOT EDIT. Effect: DO NOT EDIT Evidence: ledger:E0377, ledger:E0899, ledger:E1151</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3104A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x121" flags="0x0">
    <title>Idle Moving Mode and First Idle After Start - Speed Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed that splits stopped from moving for the idle controller. Above it the controller is in its moving mode: the idle airflow integral may run and closed loop idle speed control stays off. At or below it, the first idle after a start ends when rpm falls to desired idle (plus the offset); above it only the airflow test applies. Stock 17.5 km/h. Effect: raise = the truck counts as stopped for idle control up to a higher speed Evidence: ledger:E0378, ledger:E1103</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A21E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x122" flags="0x0">
    <title>First Idle After Start - End RPM Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The first-idle settings end once rpm is at or below desired idle plus this. Stock 0 rpm. Effect: raise = first-idle settings end sooner Evidence: ledger:E0378</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B4BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x123" flags="0x0">
    <title>First Idle After Start - End Airflow Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above the speed threshold, the first-idle settings end when predicted idle airflow plus this exceeds a limit. Stock -32 g/s (off). Effect: raise toward 0 to enable the airflow test Evidence: ledger:E0378</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B4B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x124" flags="0x30">
    <title>A/C Idle Air - Target vs A/C Compressor Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air added for the A/C compressor, by A/C compressor torque (0 to 80 Nm). The value is multiplied by an rpm factor that is 0.125 at every engine speed on stock; the scaling shown includes that factor. Stock 0.5 to 3.0 g/s. Effect: raise = more idle air with the A/C on Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>Nm A/C compressor torque</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AA2C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>0</decimalpl>
      <min>-4.000000</min>
      <max>3.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x125" flags="0x30">
    <title>A/C Idle Air Ramp-In Step vs A/C Compressor Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added per update while the A/C idle air ramps in when the compressor engages, by A/C compressor torque (0 to 80 Nm), until the A/C idle air target is reached. Stock 0.9 down to 0.5 g/s. Effect: raise = the extra idle air for the A/C comes in faster Evidence: ledger:E0379, ledger:E0948</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>Nm (A/C compressor torque)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A9F4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s per update</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x126" flags="0x30">
    <title>A/C Idle Air Sequence Hold Time vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the A/C idle air sequence holds after the air has ramped in before it ends, by engine speed (0 to 4096 rpm). Stock 1.3 s at low rpm down to 0.16 s. Effect: raise = the A/C idle air sequence stays active longer Evidence: ledger:E0379, ledger:E0936, ledger:E0948</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AA64" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x127" flags="0x0">
    <title>STFT Tip-In Reset Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: at a low speed tip-in (throttle request rising through its tip-in threshold), a trim integrator below this is reset to 1.0, so a fuel-removing trim is dropped as the throttle opens. Stock 1.0. Effect: lower = only a larger fuel-removing trim is reset at tip-in Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24DF2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x128" flags="0x0">
    <title>STFT Purge-Off Reset Threshold (Fuel Trim Monitor)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: when the fuel trim monitor shuts canister purge off, a trim integrator below this is set back to 1.0 on that pass, so a fuel-removing trim learned with purge flowing is dropped. Stock 1.0. Effect: lower = a fuel-removing trim is kept when the monitor shuts purge off Evidence: ledger:E1126</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24DC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x129" flags="0x30">
    <title>Ambient Air Temp Estimate - Intake Heat Rise vs Airflow x Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The ambient temperature estimate (PID 0x46) targets IAT minus this rise; only updated above 5 g/s and 48 km/h. Stock 50 C at standstill, 7.5 C at 80 km/h, about 4 C at 160 km/h (E0385). Effect: raise = lower ambient estimate Evidence: ledger:E0385, ledger:E0936</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <LABEL index="11" value="110" />
      <LABEL index="12" value="120" />
      <LABEL index="13" value="130" />
      <LABEL index="14" value="140" />
      <LABEL index="15" value="150" />
      <LABEL index="16" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="8" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="24" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="48" />
      <LABEL index="7" value="56" />
      <LABEL index="8" value="64" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="88" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="104" />
      <LABEL index="14" value="112" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35D1A" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x12A" flags="0x30">
    <title>Ambient Air Temp Estimate - Step per Update vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How far the ambient estimate moves toward its target each update. Stock 0.1 C at every airflow (E0385). Effect: raise = ambient estimate follows faster Evidence: ledger:E0385</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="8" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="24" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="48" />
      <LABEL index="7" value="56" />
      <LABEL index="8" value="64" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="88" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="104" />
      <LABEL index="14" value="112" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35CC8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x12B" flags="0x30">
    <title>ETC Engine Speed Limiter - Base Torque vs RPM x Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Base torque of the throttle-side engine speed limiter, by engine speed (rows) and throttle (columns). The limiter engages above about 1100 rpm with the pedal released; its torque limit is this value plus a proportional and integral correction on engine speed error (reference at least 900 rpm), and it replaces the engine torque request whenever it is lower. Stock 0 Nm at zero throttle below 1500 rpm, down to -500 Nm above, 80 to 175 Nm at the first throttle steps and 250 Nm from about 3 % throttle. Effect: raise = higher engine torque allowed when the throttle-side engine speed limiter starts acting Evidence: ledger:E0388, led...</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% throttle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1.562" />
      <LABEL index="2" value="3.125" />
      <LABEL index="3" value="4.688" />
      <LABEL index="4" value="6.25" />
      <LABEL index="5" value="7.812" />
      <LABEL index="6" value="9.375" />
      <LABEL index="7" value="10.938" />
      <LABEL index="8" value="12.5" />
      <LABEL index="9" value="14.062" />
      <LABEL index="10" value="15.625" />
      <LABEL index="11" value="17.188" />
      <LABEL index="12" value="18.75" />
      <LABEL index="13" value="20.312" />
      <LABEL index="14" value="21.875" />
      <LABEL index="15" value="23.438" />
      <LABEL index="16" value="25" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="500" />
      <LABEL index="1" value="1000" />
      <LABEL index="2" value="1500" />
      <LABEL index="3" value="2000" />
      <LABEL index="4" value="2500" />
      <LABEL index="5" value="3000" />
      <LABEL index="6" value="3500" />
      <LABEL index="7" value="4000" />
      <LABEL index="8" value="4500" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22F0A" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x12C" flags="0x30">
    <title>Pedal to Throttle-Area Demand - Slot k7 (not used on the H3)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: the rows of this map are engine speed in rpm on this calibration (the pedal map row input switch is set here; on the H3 the rows are vehicle speed), shown by running this operating system&#x27;s code. Which transmission state uses this map is set by a pedal mode 2 selector that is not in this file; the stock selection on this calibration can differ from the H3 described below. A populated pedal map (pedal % by vehicle speed to throttle-area demand) in a slot that no mode selects on the H3, so editing it has no effect on this truck. Effect: no effect on the stock H3 Evidence: ledger:E0228, ledger:E0232, ledger:...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x23DE6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="1" />
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x23E0A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>9</indexcount>
      <units>rpm (engine speed)</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23AF6" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (throttle-area demand)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x12D" flags="0x30">
    <title>Coolant Temp Sensor - Temperature Points</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Temperature at each of the 33 sensor resistance points (stock 150 C down to -40 C in 5.9 C steps); the PCM interpolates between them to get coolant temperature. Effect: reported and used coolant temperature Evidence: ledger:E0392, ledger:E1047</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2256E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x12E" flags="0x30">
    <title>Coolant Temp Sensor - Resistance Points</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor resistance at each of the 33 temperature points of the coolant temperature sensor (stock 47 ohm at 150 C to 100.7 kohm at -40 C, the standard GM thermistor). Paired with Coolant Temp Sensor - Temperature Points. Change only for a different sensor. Effect: reported and used coolant temperature Evidence: ledger:E0392, ledger:E1047</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x224E6" mmedelementsizebits="32" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ohm</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>134217727.968750</max>
      <MATH equation="X/32"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x12F" flags="0x0">
    <title>Tip-In Arming - Slip Threshold A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only) can only arm while the engine is turning less than a set amount faster than the transmission output implies in the current gear (torque converter plus gearbox slip). Below Threshold A it can arm; from Threshold A up to Threshold B it can arm only while engine torque is below the arm torque; at or above Threshold B it cannot arm. Once armed at closed throttle, opening the throttle starts the tip-in torque ramp. Stock both 250 rpm, so there is no in-between band. This is Threshold A. Effect: raise = tip-in management still arms with more converter slip Evidence: ledger:E0356, ledger:E0845, led...</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21044" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x130" flags="0x0">
    <title>Tip-In Torque Limit - Floor Outside Lash Phase</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. Outside the lash phase the tip-in torque limit is raised to at least this value. The torque reduction requested is engine torque minus the limit, so at the stock 8191 Nm the stock H3 only reduces torque during the lash phase. Lower it to also limit torque during the default and fast phases. Effect: tip-in torque management Evidence: ledger:E...</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2103C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x131" flags="0x0">
    <title>Tip-In Torque Limit - Start Floor, Alternate (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Start floor of the tip-in limit used only when a transmission-type calibration flag is 0; it is 1 on the stock H3, which uses the start floor table instead. Stock 8191 Nm. Effect: tip-in torque management Evidence: ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21040" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x132" flags="0x0">
    <title>Tip-In Torque Ramp - Lash Step Hold Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up by a step each update. The step is the default step normally, the slow lash step while the driveline is taking up slack (gearbox slip above about 10 rpm, or engine speed rising faster than the slip-based limit), and the fast step once the limit has passed its target. Once the lash step is in use it stays in use while engine speed is still changing faster than this per update. Stock -20 rpm per update. Effect: raise = the lash step is dropped sooner Evidence: ledger:E0395, ledger:E0845</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21042" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm per update</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x133" flags="0x0">
    <title>Tip-In Torque Ramp - Fast Step Input Speed Trigger</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. After a shunt and swing back, the fast step starts once input speed rises faster than this per update. Stock 10 rpm per update. Effect: tip-in torque management Evidence: ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2104A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm per update</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x134" flags="0x30">
    <title>LTFT Cell - Learn Enable (learn internal)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per fuel-trim cell: 1 = the cell may learn, 0 = it does not. Stock 1 except a few spare cells. A wrong edit silently stops trims learning in that cell. Effect: learn internal: edit with care Evidence: ledger:E0397</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37AEA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flag</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x135" flags="0x30">
    <title>Fuel Trim Monitor - Cell Ready Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per fuel trim cell: monitor passes counted in the cell before the monitor takes its value; until then the tracked value stays at 1.0. Stock 180 in every cell. The fuel trim monitor (P0171 system too lean, P0172 system too rich) tracks a per-bank value built from the long-term fuel trim code&#x27;s per-bank value, which is centred on 1.0. These per-cell settings shape it: a diagnostic, not a fueling value. Effect: raise = the monitor waits longer in a cell before using it Evidence: ledger:E0310, ledger:E0397, ledger:E0905</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37B3A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>count</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x136" flags="0x30">
    <title>Fuel Trim Monitor - Cell Use</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per fuel trim cell, how the fuel trim monitor uses it: 0 = not used, 1 = purge set cell, 2 = non purge set cell (also the cells the purge-off test measures in), sampled only while commanded purge is at or below the non purge cell purge limit. Stock 1 for cells 0 to 19, 2 for cells 21 to 37, 0 for cells 20 and 38. The fuel trim monitor (P0171 system too lean, P0172 system too rich) samples the long term fuel trim cell the engine is in; cells 0 to 20 are the purge set and 21 to 38 the non purge set. Effect: 0 = the monitor ignores that cell; changing 1 and 2 moves a cell between the purge and non purge sets Evidence: ledger:E03...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>fuel trim cell</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37B8A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>code</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x137" flags="0x30">
    <title>Fuel Trim Monitor - Cell Weight Set Index</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per fuel trim cell: which entry (21 to 38) of the weight arrays below the cell uses. The fuel trim monitor (P0171 system too lean, P0172 system too rich) tracks a per-bank value built from the long-term fuel trim code&#x27;s per-bank value, which is centred on 1.0. These per-cell settings shape it: a diagnostic, not a fueling value. Effect: changes which weights the cell uses Evidence: ledger:E0310, ledger:E0397, ledger:E0905</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37BDA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>index</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x138" flags="0x30">
    <title>Fuel Trim Monitor - Cell Weight, Above 1.0</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per weight set: when the input is above 1.0, the monitor uses 1.0 plus the excess times this weight. Stock 1.0 everywhere (the full excess). The fuel trim monitor (P0171 system too lean, P0172 system too rich) tracks a per-bank value built from the long-term fuel trim code&#x27;s per-bank value, which is centred on 1.0. These per-cell settings shape it: a diagnostic, not a fueling value. Effect: lower = the monitor sees less of a lean correction Evidence: ledger:E0310, ledger:E0397, ledger:E0905</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37C2A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x139" flags="0x30">
    <title>Fuel Trim Monitor - Cell Weight, Above 1.0, Bank 2 (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Bank 2 copy of the weight above. The H3 has one bank, so this is never used. Stock 1.0. The fuel trim monitor (P0171 system too lean, P0172 system too rich) tracks a per-bank value built from the long-term fuel trim code&#x27;s per-bank value, which is centred on 1.0. These per-cell settings shape it: a diagnostic, not a fueling value. Effect: no effect on stock (inactive) Evidence: ledger:E0310, ledger:E0397, ledger:E0905</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37C7A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x13A" flags="0x30">
    <title>Fuel Trim Monitor - Cell Weight, Below 1.0</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per weight set: when the input is below 1.0, the monitor uses 1.0 minus the shortfall times this weight. Stock 1.0 everywhere (the full shortfall). The fuel trim monitor (P0171 system too lean, P0172 system too rich) tracks a per-bank value built from the long-term fuel trim code&#x27;s per-bank value, which is centred on 1.0. These per-cell settings shape it: a diagnostic, not a fueling value. Effect: lower = the monitor sees less of a rich correction Evidence: ledger:E0310, ledger:E0397, ledger:E0905</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37CCA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x13B" flags="0x30">
    <title>Fuel Trim Monitor - Cell Weight, Below 1.0, Bank 2 (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Bank 2 copy of the weight below. The H3 has one bank, so this is never used. Stock 1.0. The fuel trim monitor (P0171 system too lean, P0172 system too rich) tracks a per-bank value built from the long-term fuel trim code&#x27;s per-bank value, which is centred on 1.0. These per-cell settings shape it: a diagnostic, not a fueling value. Effect: no effect on stock (inactive) Evidence: ledger:E0310, ledger:E0397, ledger:E0905</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37D1A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x13C" flags="0x30">
    <title>Pedal Gain Reduction - Acceleration Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle acceleration above which the pedal gain reduction can start, by driveline output torque (engine torque through converter, gear and final drive, 0 to 648 Nm) and vehicle speed (0 to 256 km/h). When the truck accelerates at or above this for the confirm time, the PCM lowers the pedal throttle request factor. Stock 120 km/h/s everywhere, which is never reached, so the reduction does not run on the stock file. Effect: lower = the pedal gain reduction starts at gentler acceleration Evidence: ledger:E0403, ledger:E0937, ledger:E1203</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>km/h (vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="32" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="96" />
      <LABEL index="4" value="128" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="192" />
      <LABEL index="7" value="224" />
      <LABEL index="8" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>Nm (driveline output torque)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="81" />
      <LABEL index="2" value="162" />
      <LABEL index="3" value="243" />
      <LABEL index="4" value="324" />
      <LABEL index="5" value="405" />
      <LABEL index="6" value="486" />
      <LABEL index="7" value="567" />
      <LABEL index="8" value="648" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2307A" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h/s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>127.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x13D" flags="0x0">
    <title>Cam and Volumetric Efficiency Deficit Blend Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fast lag weight of the cam phase transient detector: share of the new cam phase excess (cam phase above the Cam Phase Ceiling) taken into the fast filtered excess each update, for every predictor region. Stock 0.5. Effect: higher = fast value follows the excess faster, so a larger gap to the slow value and more transients flagged Evidence: ledger:E0772, ledger:E0805, ledger:E1277, ledger:E1572, ledger:E1574</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2CAAA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain (Q16, unitless)</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x13E" flags="0x0">
    <title>Idle Speed Control - Reference Freeze Reference Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: the reference freeze (see Reference Freeze RPM Error) applies only while the idle speed reference is at or below this. Stock 900 rpm. Effect: lower = the freeze applies only at lower reference speeds Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x223E0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x13F" flags="0x0">
    <title>Idle Speed Control - Reference Fall Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: rate at which the idle speed reference moves down toward its target while holding idle. Stock 40 rpm per second. Effect: raise = the idle speed reference comes down faster Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x223E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm per s</units>
    <decimalpl>0</decimalpl>
    <min>-163840.000000</min>
    <max>163835.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*5"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x140" flags="0x0">
    <title>Idle Speed Control - Reference Rise Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: rate at which the idle speed reference moves up toward its target while holding idle. Stock 400 rpm per second. Effect: raise = the idle speed reference comes up faster Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x223E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm per s</units>
    <decimalpl>0</decimalpl>
    <min>-163840.000000</min>
    <max>163835.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*5"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x141" flags="0x30">
    <title>Closed Loop Trim Step Interval - Base, O2 Lean</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): time between steps of the short term trim while the O2 reads lean. The interval is this base value, by airflow, times a factor that shortens it when the O2 signal is far past the switch point. The timer restarts after every step, so the trim keeps stepping at this interval for as long as the O2 stays on one side. Effect: raise = the trim adds fuel more slowly while the O2 reads lean Evidence: ledger:E0433, ledger:E0901, ledger:E1126</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24EB8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x142" flags="0x30">
    <title>Closed Loop Trim Step Interval - Base, O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): time between steps of the short term trim while the O2 reads rich. The interval is this base value, by airflow, times a factor that shortens it when the O2 signal is far past the switch point. The timer restarts after every step, so the trim keeps stepping at this interval for as long as the O2 stays on one side. Effect: raise = the trim removes fuel more slowly while the O2 reads rich Evidence: ledger:E0433, ledger:E0901, ledger:E1126</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24ECC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x143" flags="0x30">
    <title>Closed Loop Proportional Gain - Spare Mode</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): proportional part of the short term trim by airflow, first row while the O2 reads lean and second row while it reads rich, used in place of the normal proportional gain curves in a spare mode. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1134</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>O2 state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="O2 lean" />
      <LABEL index="1" value="O2 rich" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24F08" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x144" flags="0x30">
    <title>Closed Loop Proportional Gain - Low Baro Mode</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): proportional part of the short term trim by airflow, first row while the O2 reads lean and second row while it reads rich, used in place of the normal proportional gain curves in the low baro mode. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1134</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>O2 state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="O2 lean" />
      <LABEL index="1" value="O2 rich" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24F30" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x145" flags="0x30">
    <title>Closed Loop Proportional Gain - Coolant Window Mode</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): proportional part of the short term trim by airflow, first row while the O2 reads lean and second row while it reads rich, used in place of the normal proportional gain curves in the coolant window mode. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1134</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>O2 state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="O2 lean" />
      <LABEL index="1" value="O2 rich" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24F58" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x146" flags="0x30">
    <title>Closed Loop Proportional Gain - O2 Lean</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. This curve is the proportional size by airflow while the O2 reads lean (at factor 1.0). Stock 1.3 % at idle, 6.3 % at 4.8 g/s, 7.0 % from 8 to 29.5 g/s, 5.7 % at 40 g/s. Effect: raise = stronger proportional correction (faster, but more trim ripp...</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24F80" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x147" flags="0x30">
    <title>Closed Loop Proportional Gain - O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. This curve is the proportional size by airflow while the O2 reads rich (at factor 1.0). Stock equal to the lean curve. Effect: raise = stronger proportional correction (faster, but more trim ripple) Evidence: ledger:E0433, ledger:E0903, ledger:E1126</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24F94" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x148" flags="0x30">
    <title>Closed Loop Proportional Term Ceiling vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit of the closed loop proportional correction by airflow, before it is multiplied by the Proportional Term Ceiling Factor for the current gear, converter clutch and coolant state. Same scale as the proportional gain curves. Stock 200 %, which with the stock factors of 2.0 never limits. Effect: lower = caps the closed loop proportional correction at that airflow Evidence: ledger:E0433, ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s used airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4.8" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="13.2" />
      <LABEL index="4" value="21.8" />
      <LABEL index="5" value="29.5" />
      <LABEL index="6" value="40.3" />
      <LABEL index="7" value="51.8" />
      <LABEL index="8" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24FAA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x149" flags="0x30">
    <title>Closed Loop O2 Switch Delay - Factor, O2 Lean</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. This curve scales the switch delay (batch 56) by how far the O2 is past its switch point, while it reads lean. Stock 1.0 up to 160 mV, 0.5 from 352 mV. Effect: raise = longer delay at that distance Evidence: ledger:E0433, ledger:E0903</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24FBE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x14A" flags="0x30">
    <title>Closed Loop O2 Switch Delay - Factor, O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. This curve scales the switch delay while the O2 reads rich. Stock equal to the lean curve. Effect: raise = longer delay at that distance Evidence: ledger:E0433, ledger:E0903</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24FE2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x14B" flags="0x30">
    <title>Closed Loop Proportional Factor - O2 Lean</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. This curve scales the proportional term off idle by how far the O2 is past its switch point, while it reads lean. Stock 0.4 up to 192 mV rising to 0.8 from 352 mV. Effect: raise = stronger proportional correction at that distance Evidence: ledger...</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25006" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-2.000000</min>
      <max>1.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x14C" flags="0x30">
    <title>Closed Loop Proportional Factor - O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. This curve scales the proportional term off idle while the O2 reads rich. Stock equal to the lean curve. Effect: raise = stronger proportional correction at that distance Evidence: ledger:E0433, ledger:E0903, ledger:E1126</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2502A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-2.000000</min>
      <max>1.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x14D" flags="0x30">
    <title>Closed Loop Proportional Factor - Idle</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. This curve scales the proportional term in closed-throttle idle (both O2 states). Stock 1.0 up to 192 mV rising to 1.6 from 384 mV. Effect: raise = stronger proportional correction at idle Evidence: ledger:E0433, ledger:E0903, ledger:E0936</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2504E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-2.000000</min>
      <max>1.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x14E" flags="0x30">
    <title>Closed Loop Slow-Sensor Trim Step Interval - Base, O2 Lean (inactive)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: the map that would select the slow sensor tables on the lean side is all zero. Closed loop fuel, slow sensor tables: time between steps of the short term trim while the O2 reads lean. The interval is this base value, by airflow, times a factor that shortens it when the O2 signal is far past the switch point. The timer restarts after every step, so the trim keeps stepping at this interval for as long as the O2 stays on one side. Effect: no effect on the stock calibration Evidence: ledger:E0433, le...</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25182" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x14F" flags="0x30">
    <title>Closed Loop Slow-Sensor Trim Step Interval - Base, O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel, slow sensor tables (used while the O2 reads rich when the Alternate Tables Map selects them for the measured O2 response times): time between steps of the short term trim. The interval is this base value, by airflow, times a factor that shortens it when the O2 signal is far past the switch point. The timer restarts after every step, so the trim keeps stepping at this interval for as long as the O2 stays on one side. Effect: raise = the trim removes fuel more slowly with a slow sensor Evidence: ledger:E0433, ledge...</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25196" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x150" flags="0x30">
    <title>Closed Loop Slow-Sensor Switch Delay - Factor, O2 Lean (inactive)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this is the lean-side row of an alternate closed-loop table, and the map that would select the lean side is all zero. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). Effect: no effect on the stock calibration Evidence: ledger:E0433, ledger:E0904</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x251AE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x151" flags="0x30">
    <title>Closed Loop Slow-Sensor Switch Delay - Factor, O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). This curve scales the switch delay by how far the O2 is past its switch point. Stock 1.0 up to 160 mV, 0.5 from 352 mV. Effect: raise = longer delay at that distance Evidence: ledger:E0433, ledger:E0904</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x251D2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x152" flags="0x30">
    <title>Closed Loop Slow-Sensor Proportional Factor, O2 Lean (inactive)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this is the lean-side row of an alternate closed-loop table, and the map that would select the lean side is all zero. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). Effect: no effect on the stock calibration Evidence: ledger:E0433, ledger:E0904, ledger:E0936</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x251FE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-2.000000</min>
      <max>1.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x153" flags="0x30">
    <title>Closed Loop Slow-Sensor Proportional Factor, O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). This curve scales the proportional term off idle by how far the O2 is past its switch point. Stock 0.4 rising to 0.8 from 352 mV. Effect: raise = stronger proportional correction at that distance Evidence: ledger:E0433, ledger:E0904, ledger:E1126</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25222" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-2.000000</min>
      <max>1.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x154" flags="0x30">
    <title>Closed Loop Slow-Sensor Proportional Gain, O2 Lean (inactive)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this is the lean-side row of an alternate closed-loop table, and the map that would select the lean side is all zero. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). Effect: no effect on the stock calibration Evidence: ledger:E0433, ledger:E0904, ledger:E0936</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25246" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x155" flags="0x30">
    <title>Closed Loop Slow-Sensor Proportional Gain, O2 Rich</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). This curve is the proportional size by airflow (at factor 1.0). Stock as the normal gain but 8.7 % from 29.5 g/s. Effect: raise = stronger proportional correction Evidence: ledger:E0433, ledger:E0904, ledger:E1126</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="4.8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="13.2" />
      <LABEL index="5" value="21.8" />
      <LABEL index="6" value="29.5" />
      <LABEL index="7" value="40.3" />
      <LABEL index="8" value="51.8" />
      <LABEL index="9" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2525A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>-200.000000</min>
      <max>199.993896</max>
      <MATH equation="X/163.84"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x156" flags="0x30">
    <title>Closed Loop Slow-Sensor Proportional Factor - Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). This curve scales the proportional term in closed-throttle idle. Stock 1.0 rising to 1.6 from 384 mV. Effect: raise = stronger proportional correction at idle Evidence: ledger:E0433, ledger:E0904, ledger:E0936</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>mV past the O2 switch point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="32" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="96" />
      <LABEL index="4" value="128" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="192" />
      <LABEL index="7" value="224" />
      <LABEL index="8" value="256" />
      <LABEL index="9" value="288" />
      <LABEL index="10" value="320" />
      <LABEL index="11" value="352" />
      <LABEL index="12" value="384" />
      <LABEL index="13" value="416" />
      <LABEL index="14" value="448" />
      <LABEL index="15" value="480" />
      <LABEL index="16" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25270" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-2.000000</min>
      <max>1.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x157" flags="0x30">
    <title>Closed Loop Slow-Sensor Trim Jump</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). These are the trim jumps: idle lean (unused), idle rich, off idle lean (unused), off idle rich. Stock 0.40 % each. Effect: raise = bigger trim step at each O2 switch Evidence: ledger:E0433, ledger:E0904</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>idle / off idle, O2 state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="idle lean (unused)" />
      <LABEL index="1" value="idle rich" />
      <LABEL index="2" value="off idle lean (unused)" />
      <LABEL index="3" value="off idle rich" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x251F6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x158" flags="0x0">
    <title>A/C Refrigerant Pressure Sensor Check Enable (P0532 / P0533)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the A/C refrigerant pressure sensor circuit low / high checks on or off. 1: the PCM runs the check and can set P0532 / P0533. 0: the check never runs, so P0532 / P0533 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0532 / P0533 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x200D4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x159" flags="0x0">
    <title>P0532 Fail - Consecutive Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C refrigerant pressure sensor circuit low check P0532: the code sets after this many samples in a row read at or below the low limit. Stock 3. Effect: raise = more low samples in a row are needed to set P0532 Evidence: ledger:E1034</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x200D6" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x15A" flags="0x0">
    <title>P0533 Fail - Consecutive Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C refrigerant pressure sensor circuit high check P0533: the code sets after this many samples in a row read at or above the high limit. Stock 3. Effect: raise = more high samples in a row are needed to set P0533 Evidence: ledger:E1034</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x200D7" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x15B" flags="0x0">
    <title>P0532 Check - Sensor Voltage Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C refrigerant pressure sensor circuit low check P0532: a sample counts as low when the sensor voltage is at or below this. Stock 0.10 V. Effect: raise = higher voltages already count as a low circuit Evidence: ledger:E1048</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x200D8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>9.999847</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/6553.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x15C" flags="0x0">
    <title>P0533 Check - Sensor Voltage High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C refrigerant pressure sensor circuit high check P0533: a sample counts as high when the sensor voltage is at or above this. Stock 4.90 V. Effect: lower = lower voltages already count as a high circuit Evidence: ledger:E1048</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x200DA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>9.999847</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/6553.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x15D" flags="0x0">
    <title>P0622 Test - Run Condition, Engine Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0622 (generator field signal), engine running check: runs only below this engine speed. Stock 3000 rpm. Effect: raise = the running check also runs at higher engine speed Evidence: ledger:E1076</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x203CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x15E" flags="0x0">
    <title>P0622 Fail - Field Duty, Engine Stopped</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0622, ignition on with the engine stopped: generator field signal duty at or above this for the engine-stopped fail time sets the code. Stock 65 %. Effect: raise = a higher field signal is tolerated with the engine stopped Evidence: ledger:E1076</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x203D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x15F" flags="0x0">
    <title>P0622 Fail - Field Duty, Engine Running</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0622, engine running: generator field signal duty at or below this for the engine-running fail time sets the code. Stock 5 %. Effect: lower = a lower field signal is tolerated with the engine running Evidence: ledger:E1076</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x203D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x160" flags="0x0">
    <title>U1301 Fail Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Class 2 data link high check U1301: the code sets once the fault has been present for this long. Stock 3 s. Effect: raise = the fault must last longer before U1301 sets Evidence: ledger:E1035</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2046A" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x161" flags="0x0">
    <title>U1300 Fail Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Class 2 data link low check U1300: the code sets once the fault has been present for this long. Stock 3 s. Effect: raise = the fault must last longer before U1300 sets Evidence: ledger:E1035</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2046B" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x162" flags="0x0">
    <title>System Voltage High Threshold (P0563)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0563 (system voltage high) counts toward a fail while system voltage is at or above this, and the PCM treats voltage above it as outside the normal range. Stock 16.0 V. Effect: raise = higher voltage is tolerated before P0563 Evidence: ledger:E0978</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2049E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x163" flags="0x0">
    <title>System Voltage High Check Enable (P0563)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the system voltage high check on or off. 1: the PCM runs the check and can set P0563. 0: the check never runs, so P0563 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0563 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x204A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x164" flags="0x0">
    <title>System Voltage Low Threshold (P0562)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0562 (system voltage low) counts toward a fail while system voltage is at or below this, and the PCM treats voltage below it as outside the normal range. Stock 10.0 V. Effect: lower = lower voltage is tolerated before P0562 Evidence: ledger:E0978</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x204A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x165" flags="0x0">
    <title>System Voltage Low Check Enable (P0562)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the system voltage low check on or off. 1: the PCM runs the check and can set P0562. 0: the check never runs, so P0562 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0562 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x204AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x166" flags="0x0">
    <title>Knock Sensor Tests - Run Condition, Airmass Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock sensor checks (P0325, P0327, P0332): the checks run only when cylinder airmass is above this. The sensor signal evaluation that feeds them starts at a quarter of this airmass. Stock 0.26 g per cylinder. Effect: raise = the knock sensor checks run only at higher load Evidence: ledger:E1078</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32750" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/cyl</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>16.383750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x167" flags="0x0">
    <title>P0315 Fail - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0315 (crankshaft variation not learned) sets once the variation values have been found not learned for this long. Stock 0.5 s. Effect: raise = P0315 takes longer to set Evidence: ledger:E1040</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3459A" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x168" flags="0x0">
    <title>P0116 Test - Drive Check Intake Air Rise Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116), when coolant at start-up is warmer than intake air by more than the pass limit but less than the fail limit: after the drive check time, the code sets unless intake air has risen at least this much above its lowest reading since start, in which case no decision is made. Stock 5 C. Effect: raise = a larger intake air rise is needed to avoid the fail Evidence: ledger:E1022</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3514E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x169" flags="0x0">
    <title>P0116 Test - Startup Intake Air Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116), when coolant at start-up is warmer than intake air by more than the pass limit but less than the fail limit: no decision is made if intake air temperature at start-up was at or below this. Stock 10 C. Effect: lower = the test also decides after colder starts Evidence: ledger:E1022</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35150" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x16A" flags="0x0">
    <title>P0116 Test - Drive Check Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116), when coolant at start-up is warmer than intake air by more than the pass limit but less than the fail limit: the decision is made after more than this much driving above the drive check speed. Stock 400 s. Effect: raise = more driving is needed before the decision Evidence: ledger:E1022</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35152" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x16B" flags="0x0">
    <title>P0116 Test - Drive Check Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116), when coolant at start-up is warmer than intake air by more than the pass limit but less than the fail limit: only time spent above this vehicle speed counts toward the drive check time. Stock 40 km/h. Effect: raise = only faster driving counts Evidence: ledger:E1022</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35154" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x16C" flags="0x0">
    <title>P0116 Test - Long Crank Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116), when coolant at start-up is warmer than intake air by more than the pass limit but less than the fail limit: if the engine cranked for at least this long, the code sets at once when fuel level is above the long crank fuel level, and otherwise no decision is made. Stock 10 s. Effect: raise = only longer cranking takes this path Evidence: ledger:E1022</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35156" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x16D" flags="0x0">
    <title>P0116 Test - Long Crank Fuel Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116), when coolant at start-up is warmer than intake air by more than the pass limit but less than the fail limit: after a long crank the code sets only if fuel level is above this. Stock 10 %. Effect: raise = more fuel is needed for the long crank fail Evidence: ledger:E1022</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3517C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x16E" flags="0x0">
    <title>P0117 / P1114 Check - Hot Soak Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit low check: for this long after a start, low-circuit samples are ignored while minimum intake air temperature is above the hot soak limit. Stock 10 s. Effect: raise = hot soak readings are ignored for longer after a start Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35216" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x16F" flags="0x0">
    <title>P0117 / P1114 Check - Hot Soak Intake Air Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit low check: minimum intake air temperature above which low-circuit samples are ignored right after a start. Stock 70 C. Effect: lower = samples are ignored after a cooler soak too Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35218" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x170" flags="0x0">
    <title>P0117 / P1114 Check - Sensor Resistance Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant temperature sensor circuit low check: a sample counts as low when the sensor resistance is below this (a shorted sensor or wire). Stock 25 ohm. Effect: raise = higher resistances already count as a low circuit Evidence: ledger:E1047</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3521A" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ohm</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>134217727.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x171" flags="0x0">
    <title>P0118 / P1115 Check - Sensor Resistance High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant temperature sensor circuit high check: a sample counts as high when the sensor resistance is above this (an open sensor or wire). Stock 1.8 Mohm. Effect: lower = lower resistances already count as a high circuit Evidence: ledger:E1047</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3521E" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ohm</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>134217727.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x172" flags="0x0">
    <title>P0117 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit low check: P0117 sets once this many low-circuit samples are counted in a test window. Stock 50. Effect: raise = more low samples are needed to set P0117 Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35222" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x173" flags="0x0">
    <title>P1114 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit low check: P1114 (intermittent) sets once this many low-circuit samples are counted in its longer test window. Stock 100. Effect: raise = more low samples are needed to set P1114 Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35224" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x174" flags="0x0">
    <title>P0118 / P1115 Check - Cold Start Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit high check: for this long after a start, high-circuit samples are ignored while minimum intake air temperature is below the cold start limit. Stock 60 s. Effect: raise = cold start readings are ignored for longer after a start Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3522A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x175" flags="0x0">
    <title>P0118 / P1115 Check - Cold Start Intake Air Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit high check: minimum intake air temperature below which high-circuit samples are ignored right after a start. Stock -7 C. Effect: raise = samples are ignored after a milder cold start too Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3522C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x176" flags="0x0">
    <title>P0118 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit high check: P0118 sets once this many high-circuit samples are counted in a test window. Stock 50. Effect: raise = more high samples are needed to set P0118 Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3522E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x177" flags="0x0">
    <title>P1115 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant sensor circuit high check: P1115 (intermittent) sets once this many high-circuit samples are counted in its longer test window. Stock 100. Effect: raise = more high samples are needed to set P1115 Evidence: ledger:E1010</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35230" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x178" flags="0x0">
    <title>Coolant Temp Sensor Circuit Checks Enable (P0117 / P0118 / P1114 / P1115)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the coolant temperature sensor circuit low / high and intermittent checks on or off. 1: the PCM runs the check and can set P0117 / P0118 / P1114 / P1115. 0: the check never runs, so P0117 / P0118 / P1114 / P1115 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0117 / P0118 / P1114 / P1115 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35236" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x179" flags="0x0">
    <title>P0442 Fail - Threshold After a Failure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0442 (small leak, engine-off test): threshold used in place of the normal fail threshold once P0442 has failed, so the running average has to come down to this before the code can pass again. Stock 0.35. Effect: raise = it is easier to pass again after a failure Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35766" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x17A" flags="0x0">
    <title>P0442 Fail - Leak Result Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0442 (small leak, engine-off test) sets when the running average of the leak result rises above this. The result of one test is 1 minus (vacuum reached minus pressure reached) divided by the reference: 0 for a tight tank, 1 when the tank pressure did not move at all. Stock 0.55. Effect: raise = a larger average leak result is needed to set P0442 Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35768" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x17B" flags="0x0">
    <title>P0442 - Averaging Weight After a Failure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0442: share of each new leak result taken into the running average once P0442 has failed. Stock 0.175. Effect: raise = each test moves the average more Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3576A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x17C" flags="0x0">
    <title>P0451 - Averaging Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): share of each new zero shift rating taken into the running average. Stock 0.20. Effect: raise = each zero check moves the average more Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3576C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x17D" flags="0x0">
    <title>P0451 - Averaging Weight After a Failure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): the same share once P0451 has failed. Stock 0.20. Effect: raise = each zero check moves the average more Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3576E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x17E" flags="0x0">
    <title>P0451 Fail - Zero Shift Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): the code sets when the running average of the zero shift rating rises above this (a rating of 1.0 is a shift equal to the zero shift limit). Stock 0.73. Effect: raise = a larger average zero shift is needed to set P0451 Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35786" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x17F" flags="0x0">
    <title>P0451 Fail - Threshold After a Failure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): threshold used in place of the normal one once P0451 has failed. Stock 0.40. Effect: raise = it is easier to pass again after a failure Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35788" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x180" flags="0x0">
    <title>P0442 - Averaging Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0442: share of each new leak result taken into the running average. Stock 0.175. Effect: raise = each test moves the average more Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35FFA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x181" flags="0x0">
    <title>P0522 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil pressure sensor circuit low check P0522 (switched off in the stock calibration): the code sets once this many samples in a test window read below the low limit. Stock 50. Effect: raise = more low samples are needed to set P0522 Evidence: ledger:E1042</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3618E" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x182" flags="0x0">
    <title>P0522 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil pressure sensor circuit low check P0522 (switched off in the stock calibration): a test window that reaches this many samples without failing passes. Stock 100. Effect: raise = each test window is longer Evidence: ledger:E1042</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3618F" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x183" flags="0x0">
    <title>P0523 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil pressure sensor circuit high check P0523 (switched off in the stock calibration): the code sets once this many samples in a test window read above the high limit. Stock 50. Effect: raise = more high samples are needed to set P0523 Evidence: ledger:E1042</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36194" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x184" flags="0x0">
    <title>P0523 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil pressure sensor circuit high check P0523 (switched off in the stock calibration): a test window that reaches this many samples without failing passes. Stock 100. Effect: raise = each test window is longer Evidence: ledger:E1042</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36195" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x185" flags="0x0">
    <title>P0452 Check - Sensor Voltage Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel tank pressure sensor circuit low check P0452: a sample counts as low when the sensor voltage is below this. Stock 0.10 V. Effect: raise = higher voltages already count as a low circuit Evidence: ledger:E1016</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3733E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x186" flags="0x0">
    <title>P0453 Check - Sensor Voltage High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel tank pressure sensor circuit high check P0453: a sample counts as high when the sensor voltage is above this. Stock 4.90 V. Effect: lower = lower voltages already count as a high circuit Evidence: ledger:E1016</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37340" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x187" flags="0x0">
    <title>P2026 Fail - Sensor Resistance Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. EVAP fuel vapour temperature sensor circuit low check (P2026): a resistance below this counts as a fault sample. Stock 0 ohm. The check is switched off on this truck (code disabled), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0434, ledger:E1482</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37A86" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ohm</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>134217727.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x188" flags="0x0">
    <title>P2027 Fail - Sensor Resistance Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. EVAP fuel vapour temperature sensor circuit high check (P2027): a resistance above this counts as a fault sample. Stock 1,000,000 ohm. The check is switched off on this truck (code disabled), so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0434, ledger:E1482</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37A8A" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ohm</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>134217727.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x189" flags="0x0">
    <title>P0325 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock sensor circuit check P0325: the code sets once this many samples in a test window show the circuit fault. Stock 40. Effect: raise = more fault samples are needed to set P0325 Evidence: ledger:E1015</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38688" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x18A" flags="0x0">
    <title>P0325 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock sensor circuit check P0325: a test window that reaches this many samples without failing passes. Stock 80. Effect: raise = each test window is longer Evidence: ledger:E1015</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38689" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x18B" flags="0x0">
    <title>P0326 Test - Run Condition, Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0326 knock sensor performance test only runs while engine speed is at or above this. Stock 1800 rpm. Effect: raise = the test needs a higher rpm to run Evidence: ledger:E1015</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38690" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x18C" flags="0x0">
    <title>Knock Sensor 1 Circuit Low Check Enable (P0327)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the knock sensor 1 circuit low check on or off. 1: the PCM runs the check and can set P0327. 0: the check never runs, so P0327 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0327 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38694" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x18D" flags="0x0">
    <title>Knock Sensor 2 Circuit Low Check Enable (P0332)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the knock sensor 2 circuit low check on or off. 1: the PCM runs the check and can set P0332. 0: the check never runs, so P0332 is never set and never reported as passed. Stock 0 (off). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0332 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38696" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x18E" flags="0x0">
    <title>P0327 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock sensor low input check P0327: the code sets once this many samples in a test window show the low input fault. Stock 80. Effect: raise = more fault samples are needed to set P0327 Evidence: ledger:E1015</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38698" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x18F" flags="0x0">
    <title>P0332 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock sensor 2 low input check P0332 (switched off in the stock calibration): the code sets once this many samples in a test window show the low input fault. Stock 80. Effect: raise = more fault samples are needed to set P0332 Evidence: ledger:E1039</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38699" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x190" flags="0x0">
    <title>P0327 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock sensor low input check P0327: a test window that reaches this many samples without failing passes. Stock 100. Effect: raise = each test window is longer Evidence: ledger:E1015</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3869A" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x191" flags="0x0">
    <title>P0332 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock sensor 2 low input check P0332 (switched off in the stock calibration): a test window that reaches this many samples without failing passes. Stock 80. Effect: raise = each test window is longer Evidence: ledger:E1039</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3869B" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x192" flags="0x0">
    <title>P0103 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAF sensor circuit high check P0103: the code sets once this many samples in a test window read above the high limit. Stock 30. Effect: raise = more high samples are needed to set P0103 Evidence: ledger:E1031</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3869C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x193" flags="0x0">
    <title>P0103 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAF sensor circuit high check P0103: a test window that reaches this many samples without failing passes. Stock 40. Effect: raise = each test window is longer Evidence: ledger:E1031</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3869E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x194" flags="0x0">
    <title>P0102 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAF sensor circuit low check P0102: the code sets once this many samples in a test window read below the low limit. Stock 30. Effect: raise = more low samples are needed to set P0102 Evidence: ledger:E1031</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x386A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x195" flags="0x0">
    <title>P0102 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAF sensor circuit low check P0102: a test window that reaches this many samples without failing passes. Stock 40. Effect: raise = each test window is longer Evidence: ledger:E1031</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x386A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x196" flags="0x0">
    <title>PCM Memory Checksum Check Enable (P0601)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the PCM memory checksum check on or off. 1: the PCM runs the check and can set P0601. 0: the check never runs, so P0601 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0601 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A32" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x197" flags="0x0">
    <title>P1380 / P1381 Test - Run Condition, RPM Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P1380 / P1381 test only runs while engine speed is at or below this. Stock 6200 rpm. Effect: raise = the test also runs at higher engine speeds Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A76" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x198" flags="0x0">
    <title>P1380 / P1381 Test - Run Condition, Load Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P1380 / P1381 test only runs while the engine load seen by the misfire monitor is at or below this. Stock 100 %. Effect: lower = the test stops running at high load Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A78" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x199" flags="0x0">
    <title>Misfire - Single Exceedance Load</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: a catalyst-damaging misfire normally needs three exceedances (or one seen earlier) before P0300 sets. When load at the end of the window is above this, one is enough. Stock 75 %. Effect: raise = the one-exceedance rule needs higher load Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x19A" flags="0x0">
    <title>Misfire - Single Exceedance Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: when engine speed at the end of the window is above this, one catalyst-damaging exceedance is enough to set P0300. Stock 2600 rpm. Effect: raise = the one-exceedance rule needs higher engine speed Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x19B" flags="0x0">
    <title>P2610 - Start Window, Timer Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off timer diagnostic (P2610): the check only starts while the engine-off timer reads at or below this (the timer counts about once a second); a reading outside the start window scores a start failure. Stock 10. Effect: raise = the check may start with a higher timer reading Evidence: ledger:E1039</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A3C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x19C" flags="0x0">
    <title>P2610 - Start Window, Timer Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off timer diagnostic (P2610): the check only starts while the engine-off timer reads at or above this; a reading outside the start window scores a start failure. Stock 0. Effect: raise = the check needs a higher timer reading to start Evidence: ledger:E1039</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A3E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x19D" flags="0x0">
    <title>P2610 - Maximum Time Between Timer Counts</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off timer diagnostic (P2610): a count of the PCM&#x27;s engine-off timer is a good sample only if it comes within this long of the previous count. Stock 1.39 s. Effect: raise = slower timer counts still pass Evidence: ledger:E0829, ledger:E0963</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A42" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x19E" flags="0x0">
    <title>P2610 - Minimum Time Between Timer Counts</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off timer diagnostic (P2610): a count of the PCM&#x27;s engine-off timer is a good sample only if it comes at least this long after the previous count. Stock 0.575 s. Effect: lower = faster timer counts still pass Evidence: ledger:E0829, ledger:E0963</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A44" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x19F" flags="0x0">
    <title>P2610 - Bad Samples to Fail</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off timer diagnostic (P2610): P2610 sets after this many bad samples. Stock 3. Effect: raise = P2610 needs more bad samples to set Evidence: ledger:E0829, ledger:E0963</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A46" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1A0" flags="0x0">
    <title>P2610 - Timer Stall Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off timer diagnostic (P2610): if the engine-off timer does not count for this long, the check scores a bad sample (before the check starts, it retries after this long). Stock 1.39 s. Effect: raise = a stalled timer is noticed later Evidence: ledger:E0829, ledger:E0963</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A4C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1A1" flags="0x0">
    <title>P2610 - Samples to Pass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off timer diagnostic (P2610): the check reports a pass after this many samples. Stock 10. Effect: raise = the check runs longer before it passes Evidence: ledger:E0829, ledger:E0963</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A4E" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1A2" flags="0x0">
    <title>P1574 Fail - Deceleration Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): the code sets once this many counted decelerations had the first input change state while the second did not. Stock 5. Effect: raise = more mismatching decelerations are needed to set P1574 Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A68" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1A3" flags="0x0">
    <title>P1574 Pass - Deceleration Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): the check passes once this many decelerations have been counted without reaching the fail count. Stock 5. Effect: raise = more counted decelerations are needed for a pass Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A69" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1A4" flags="0x0">
    <title>A/C Coolant Overheat Cut - Cut Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The A/C compressor is switched off and kept off once engine coolant temperature rises above this. Stock 122.7 degC. Effect: raise = the A/C keeps running to a higher coolant temperature Evidence: ledger:E1036</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x202C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1A5" flags="0x0">
    <title>A/C Coolant Overheat Cut - Re-Enable Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a coolant overheat cut the A/C compressor is allowed again once engine coolant temperature falls below this. Stock 120 degC. Effect: raise = the A/C is allowed again at a higher coolant temperature Evidence: ledger:E1036</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x202C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1A6" flags="0x0">
    <title>A/C WOT Cut - Maximum Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: the compressor is held off for at most this long per cut. Stock 0 s, which turns the whole WOT cut off. Effect: raise from 0 = the WOT A/C cut becomes active and can last this long Evidence: ledger:E1009</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20416" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1A7" flags="0x0">
    <title>A/C WOT Cut - Lockout Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: after a cut ends, another cut cannot start for this long. Stock 0 s. Effect: raise = longer wait between cuts Evidence: ledger:E1009</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20418" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1A8" flags="0x0">
    <title>A/C WOT Cut - Minimum Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: once started, a cut lasts at least this long even if throttle or rpm leave their limits. Stock 0 s. Effect: raise = each cut lasts longer Evidence: ledger:E1009</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2041C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1A9" flags="0x0">
    <title>A/C WOT Cut - Release Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Wide-open-throttle A/C cut: after throttle drops back below the re-enable value, the cut is held this much longer. Stock 1.5 s. Effect: raise = the compressor stays off longer after lifting Evidence: ledger:E1009</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20426" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1AA" flags="0x0">
    <title>A/C Re-Enable - Refrigerant Pressure High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a high pressure cut, the A/C compressor is allowed again once refrigerant pressure falls below this. Stock 2206 kPa (320 psi). Effect: lower = the compressor stays cut until pressure drops further Evidence: ledger:E1008</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2044A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1AB" flags="0x0">
    <title>A/C Disable - Refrigerant Pressure Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C compressor is cut when refrigerant pressure falls below this. Stock 159 kPa (23 psi). Effect: raise = the compressor is cut at a higher pressure Evidence: ledger:E1008</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2044C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1AC" flags="0x0">
    <title>A/C Re-Enable - Refrigerant Pressure Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a low pressure cut, the A/C compressor is allowed again once refrigerant pressure rises above this. Stock 276 kPa (40 psi). Effect: raise = the compressor stays cut until pressure recovers further Evidence: ledger:E1008</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2044E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1AD" flags="0x0">
    <title>Cruise Control - Vehicle Speed Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: how fast the vehicle speed the cruise controller works from follows the measured speed, as the fraction of the gap closed per update. Stock 0.05. Effect: lower = the cruise speed signal is smoothed more (slower to react) Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2192C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1AE" flags="0x0">
    <title>Cruise Control - Switch Press Time to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: from standby, a cruise switch must have been pressed for at least this long before cruise sets at the current speed. Stock 0.04 s. Effect: raise = the switch must be held longer before cruise sets Evidence: ledger:E1045</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x21938" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1AF" flags="0x0">
    <title>Cruise Control - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: an active cruise is cancelled if the engine has run for less than this. Stock 5 s. Effect: raise = cruise cannot stay engaged until later after a start Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x21948" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1B0" flags="0x0">
    <title>Cruise Control - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: an active cruise is cancelled when system voltage falls below this. Stock 9 V. Effect: raise = cruise cancels at a higher system voltage Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2194A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1B1" flags="0x0">
    <title>Cruise Control - System Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: an active cruise is cancelled when system voltage rises above this. Stock 18 V. Effect: lower = cruise cancels at a lower system voltage Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2194C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1B2" flags="0x0">
    <title>Cruise Control - Engage Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: set, resume and the speed tap functions only work while vehicle speed is at or above this. Stock 40 km/h (24.9 mph). Effect: lower = cruise can be set at a lower speed Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x21954" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1B3" flags="0x0">
    <title>Cruise Control - Engage Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: set, resume and the speed tap functions only work while vehicle speed is at or below this. Stock 225 km/h (140 mph). Effect: lower = cruise cannot be set above a lower speed Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x21956" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1B4" flags="0x0">
    <title>Cruise Control - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: an active cruise is cancelled when engine speed falls below this. Stock 500 rpm. Effect: raise = cruise cancels at a higher engine speed Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x21958" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1B5" flags="0x0">
    <title>Cruise Control - RPM Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: an active cruise is cancelled when engine speed rises above this. Stock 6470 rpm. Effect: lower = cruise cancels at a lower engine speed Evidence: ledger:E1044</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2195A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1B6" flags="0x0">
    <title>Cruise Control - Tap Speed Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: each tap up or tap down changes the set speed by this much. Stock 1.61 km/h (1 mph). Effect: raise = each tap changes the set speed by more Evidence: ledger:E1045</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x21964" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1B7" flags="0x0">
    <title>Idle Speed Control - Settle Idle Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: added to desired idle from the start of closed loop idle control until the idle speed has been settled for the settle time. Stock 0 rpm. Effect: raise = idle is held higher until it has settled Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x223D8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1B8" flags="0x0">
    <title>Idle Speed Control - Settle Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: below this engine speed the settle timer restarts. Stock 450 rpm. Effect: raise = idle counts as settled only above a higher engine speed Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x223DA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1B9" flags="0x0">
    <title>Idle Speed Control - Settle RPM Error Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: the settle timer runs while the average rpm error is at or below this. Stock 50 rpm. Effect: lower = idle must be closer to target to count as settled Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x223DC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1BA" flags="0x0">
    <title>Idle Speed Control - Reference Freeze RPM Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: the idle speed reference stops moving toward its target while the rpm error is at or above this and the reference is at or below the freeze reference maximum. Stock 50 rpm. Effect: raise = the reference keeps moving with a larger rpm error Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x223DE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1BB" flags="0x0">
    <title>Idle Speed Control - Throttle Open Idle Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: added to desired idle while the throttle reads slightly open (see Throttle Open Threshold) and for the hold time after it closes. Stock 0 rpm. Effect: raise = idle target is higher while and just after the driver touches the throttle Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x223E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1BC" flags="0x0">
    <title>Idle Speed Control - Integral Update Time, Acquire</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: time between integral steps while engine speed is coming down to idle. Stock 0.025 s (every pass). Effect: raise = the integral steps less often while acquiring idle Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x22422" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>1638.375000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/40"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1BD" flags="0x0">
    <title>Idle Speed Control - Integral Update Time, Control</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: time between integral steps while holding idle. Stock 0.4 s. Effect: raise = the integral steps less often at idle Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x22424" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>1638.375000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/40"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1BE" flags="0x0">
    <title>Idle Speed Control - MAP Filter, Control, In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: filter on the manifold pressure the controller&#x27;s airflow model uses, while holding idle in gear; fraction of the change taken every 25 ms. Stock 0.70. Effect: raise = the model follows manifold pressure faster Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x22426" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1BF" flags="0x0">
    <title>Idle Speed Control - MAP Filter, Control, Park / Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: same filter while holding idle in Park or Neutral. Stock 0.07. Effect: raise = the model follows manifold pressure faster Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x22428" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1C0" flags="0x0">
    <title>Idle Speed Control - MAP Filter, Acquire, In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: same filter in the other controller states, in gear. Stock 0.07. Effect: raise = the model follows manifold pressure faster Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2242A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1C1" flags="0x0">
    <title>Idle Speed Control - MAP Filter, Acquire, Park / Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: same filter in the other controller states, in Park or Neutral. Stock 0.07. Effect: raise = the model follows manifold pressure faster Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2242C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1C2" flags="0x0">
    <title>Idle Speed Control - Throttle Open Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: share of each new throttle reading taken into the filtered throttle area used for the throttle open flag. Stock 0.25. Effect: raise = the flag follows the throttle faster Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x22430" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1C3" flags="0x0">
    <title>Idle Speed Control - Throttle Open Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: filtered throttle area above the idle area at or above this counts as the driver being on the throttle: the idle integral may not step down and the throttle open idle offset applies. Stock 0.64 %. Effect: raise = more throttle is needed before the controller treats it as driver input Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x22432" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1C4" flags="0x0">
    <title>Idle Speed Control - A/C Hold Airflow Decay Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: the extra airflow held when the A/C clutch engages is removed by this much every 12.5 ms once its hold time is over. Stock 0.052 g/s (about 4.1 g/s per second). Effect: raise = the A/C hold airflow is removed faster Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x22438" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1C5" flags="0x30">
    <title>Idle A/C Turn-On Airflow Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the extra idle airflow added when the A/C compressor turns on is held at full value before the decay step starts removing it. Stock 0.40 s. Effect: raise = the A/C turn-on airflow is held longer before it starts to decay Evidence: ledger:E0776, ledger:E1221</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>field</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22482" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1C6" flags="0x0">
    <title>High-Load Monitor - Intake Vacuum Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. High-load monitor: its timer runs only while intake vacuum is below this (high engine load); at or above it the timer starts again from zero. Stock 5.0 kPa. Effect: raise = more engine operation counts as high load Evidence: ledger:E0775, ledger:E1265</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22EC6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1C7" flags="0x0">
    <title>Pedal Gain Reduction - Torque Sample Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How far back the driveline output torque sample used for the acceleration threshold row is taken, in 0.05 s steps (0 to 0.3 s; higher values act as 0.3 s). Stock 0 (current torque). Effect: raise = the threshold uses an older driveline torque sample Evidence: ledger:E0775, ledger:E1203</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23074" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1C8" flags="0x0">
    <title>Pedal Gain Reduction - Traction Control Immediate Start Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While traction control is cutting torque and the truck accelerates at or above the pedal gain reduction acceleration threshold, the reduction starts at once, without waiting the Confirm Time, when the traction control torque limit is below this share of the net engine torque. Stock 0.05 (5 percent). Range 0 to 1.0. Effect: raise = milder traction control torque cuts also start the pedal gain reduction at once Evidence: ledger:E0781, ledger:E0918, ledger:E1203, ledger:E1207</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2311C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1C9" flags="0x0">
    <title>Pedal Gain Increase - Transmission State</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transmission state (0-3 = 1st-4th, 6 Neutral, 7 Reverse, 8 Park) the pedal gain increase learn requires, used only when the Ignore Transmission State switch is 0. Stock 0 (1st), switch stock 1, so it is not used. Effect: selects the one transmission state the learn runs in, when the state match is enabled Evidence: ledger:E0436, ledger:E1211, ledger:E1577</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23232" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>state</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1CA" flags="0x0">
    <title>Pedal Gain Increase - Ignore Transmission State</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Switch: 1 lets the pedal gain increase learn run in any transmission state, 0 limits it to the Transmission State word. Stock 1. Effect: 0 = the learn runs only in the Transmission State word&#x27;s state Evidence: ledger:E0775, ledger:E1211, ledger:E1577</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23268" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1CB" flags="0x30">
    <title>Pedal Map Select vs Trans State - 4WD-Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Which pedal to throttle map is used in each transmission state in 4WD-Low: 0 = 4WD-Low forward gears map, 1 = 4WD-Low Park/Neutral map, 2 = 4WD-Low Reverse map. Stock 1 in Neutral and Park, 2 in Reverse, 0 elsewhere. The choice changes only while the pedal is at rest or wide open. Allowed values are 0, 1 and 2 only; any other value makes the pedal read the wrong map or no map. Effect: changes which 4WD-Low pedal map is used in that transmission state Evidence: ledger:E0240, ledger:E0781, ledger:E1210</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>transmission state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="Neutral" />
      <LABEL index="7" value="Reverse" />
      <LABEL index="8" value="Park" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23D96" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>map slot</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1CC" flags="0x0">
    <title>Pedal Response Change - Wide Open Pedal Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal response changes (pedal map selection and any raise of the pedal request factor) are only taken while the pedal is at rest or wide open. The pedal counts as wide open above this position while manifold vacuum is below the Wide Open Vacuum Threshold vs RPM. Stock 90 %. Effect: lower = less pedal is needed to count as wide open, so pedal response changes are taken more readily Evidence: ledger:E0781, ledger:E1118, ledger:E1209</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23DBA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1CD" flags="0x0">
    <title>Pedal Response Change - Pedal At Rest Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal response changes (pedal map selection and any raise of the pedal request factor) are only taken while the pedal is at rest or wide open. The pedal counts as at rest at or below this position. Stock 1.0 %. Effect: raise = the pedal counts as at rest further into its travel, so pedal response changes are taken more readily Evidence: ledger:E0781, ledger:E1118, ledger:E1209</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23DE0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1CE" flags="0x0">
    <title>Pedal Map Speed Input - Minimum Rise Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest rate at which the vehicle speed used by the pedal map may rise toward the actual speed. The rise rate is the larger of this and the pedal gain reduction acceleration threshold; a drop in speed is followed at once. Stock 128 km/h/s (the largest value), so the speed input follows within an update or two. At 0 with a zero threshold the speed input stops rising. Range 0 to 128. Effect: lower = the pedal map&#x27;s speed input lags behind a rising vehicle speed Evidence: ledger:E0775, ledger:E1203, ledger:E1210, ledger:E1213</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23E1C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1CF" flags="0x0">
    <title>Pedal Filter - Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal filter: share of the gap between the pedal demand and its filtered value that is closed every 12.5 ms. It is the lowest gain the filter may use, and on the stock file it is the gain at all times. Stock 0.8. Effect: lower = softer, slower pedal response; 1.0 = no filtering Evidence: ledger:E1118</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2414E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1D0" flags="0x0">
    <title>Pedal Position - Dead Band at Rest</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal: pedal travel above the learned rest position that still reads as 0 % pedal. Stock 3 %. Effect: raise = more free travel before the pedal starts to act Evidence: ledger:E1120</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x24176" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1D1" flags="0x0">
    <title>Pedal Position - Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal: highest pedal value passed on to the pedal map. Stock 100 %: no limit. Effect: lower = the pedal map never sees more than this pedal position Evidence: ledger:E1120</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x24178" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1D2" flags="0x0">
    <title>Purge Trim Feedback - Trim Above Which Purge May Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, fuel trim feedback: while the applied long term fuel trim is above this, the purge trim factor steps up (purge is not pulling much fuel out of the trim). Stock 0.85. Effect: raise = purge is held back until the trim is closer to 1.0 Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24376" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1D3" flags="0x0">
    <title>Purge Trim Feedback - Trim Below Which Purge Falls</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, fuel trim feedback: while the applied long term fuel trim is at or below this, the purge trim factor steps down. Stock 0.82. Effect: raise = purge is cut back at a smaller fuel trim correction Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24378" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1D4" flags="0x0">
    <title>Purge Trim Feedback - Factor Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, fuel trim feedback: amount the purge trim factor moves on each update. Stock 0.001. Effect: raise = the purge trim factor moves faster Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2437A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1D5" flags="0x0">
    <title>Purge Trim Feedback - Factor Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, fuel trim feedback: highest value of the purge trim factor. Stock 1.0. Effect: lower = less purge even with a healthy fuel trim Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2437C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1D6" flags="0x0">
    <title>Purge Trim Feedback - Factor Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, fuel trim feedback: lowest value of the purge trim factor. Stock 0.5. Effect: raise = purge is cut back less when the trim is pulling fuel Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2437E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1D7" flags="0x0">
    <title>Purge Trim Feedback - Factor at Key-On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, fuel trim feedback: value of the purge trim factor at key-on. Stock 1.0. Effect: lower = each trip starts with less purge Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24380" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1D8" flags="0x0">
    <title>Purge O2 Feedback - Rich Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: front O2 voltage at or above this counts as rich and steps the purge factor (1.0 = full purge request) down. Stock 750 mV. Effect: raise = a richer mixture is needed before purge is cut back Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x243AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1D9" flags="0x0">
    <title>Purge O2 Feedback - Lean Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: front O2 voltage below this counts as lean and steps the purge factor (1.0 = full purge request) up. Between the lean and rich voltages the factor holds. Stock 450 mV. Effect: lower = a leaner mixture is needed before purge is increased Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x243AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1DA" flags="0x0">
    <title>Purge O2 Feedback - Step Period After Long Rich Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: time between steps of the purge factor once the mixture has been rich longer than the rich time curve. Stock 0.2 s. Effect: raise = slower steps Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x243AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1DB" flags="0x0">
    <title>Purge O2 Feedback - Step Period After the Top Was Reached</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: time between steps up of the purge factor once it has reached its top value on this trip. Stock 0.2 s. Effect: raise = slower steps up later in the trip Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x243B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1DC" flags="0x0">
    <title>Purge O2 Feedback - Step Period</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: normal time between steps of the purge factor. Stock 0.2 s. Effect: raise = slower steps Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x243B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1DD" flags="0x0">
    <title>Purge O2 Feedback - Step Down After Long Rich Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: step down of the purge factor once the mixture has been rich longer than the rich time curve. Stock 0.015. Effect: raise = purge is cut back faster when the mixture stays rich Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x243B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1DE" flags="0x0">
    <title>Purge Flow - Reference Flow Full Scale</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge: value of the purge reference flow that counts as full flow. Long term fuel trim applies the purge learned correction in proportion to the reference flow divided by this. It defines the purge flow units used by the other purge flow curves. Stock 123. Effect: raise = the same reference flow counts as a smaller share of full purge on the fuel trim side Evidence: ledger:E1122</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2444C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flow units</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1DF" flags="0x0">
    <title>Purge Amount - Factor Cap</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount: highest value of the combined purge factor (O2 feedback factor times trim factor, after the enrichment multipliers). Stock 1.0: no extra limit. Effect: lower = purge is limited to that share of the full request Evidence: ledger:E1119</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24498" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E0" flags="0x0">
    <title>Purge Amount - Multiplier During Catalyst Protection Enrichment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount: multiplier on the purge factor while catalyst over-temperature enrichment is active. Stock 1.0: no change. Effect: lower = less purge during catalyst protection enrichment Evidence: ledger:E1119</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2449A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E1" flags="0x0">
    <title>Purge Amount - Multiplier During Engine Over-Temperature Enrichment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount: multiplier on the purge factor while coolant over-temperature enrichment is active. Stock 1.0: no change. Effect: lower = less purge during over-temperature enrichment Evidence: ledger:E1119</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2449E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E2" flags="0x0">
    <title>Purge Amount - Multiplier During Power Enrichment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount: multiplier on the purge factor while power enrichment is active. Stock 1.0: no change. Effect: lower = less purge at wide open throttle Evidence: ledger:E1119</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x244A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E3" flags="0x0">
    <title>Purge Amount - Tank Vacuum Cap Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount: time the fuel tank vacuum must call for less purge than the factor cap before the tank vacuum cap is applied. Stock 5 s. Effect: raise = the tank vacuum cap acts later Evidence: ledger:E1123</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x244A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E4" flags="0x0">
    <title>Purge Enable - Closed Loop Time Before Purge Resumes</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: time in closed loop fuel control before purge comes back on when it has already run on this trip. Stock 0 s: at once. Effect: raise = purge comes back later after each return to closed loop Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x245A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E5" flags="0x0">
    <title>Purge Enable - Run Time That Waives the First Purge Speed and Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: once the engine has run longer than this, the first purge of a trip no longer needs the minimum speed and airflow. Stock 0 s, so those two conditions never apply. Effect: raise = the first purge of a trip waits for the minimum speed and airflow until the engine has run this long Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x245CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E6" flags="0x0">
    <title>Purge Enable - Speed to Unblock</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: once purge has been blocked by low throttle or low speed, it is released when speed is at or above this (or throttle at or above its unblock value). Stock 0: this condition is off. Effect: raise = purge stays blocked up to a higher speed Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x245F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E7" flags="0x0">
    <title>Purge Enable - Speed Below Which Purge Is Blocked</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: purge is blocked when vehicle speed is below this or throttle is below its block value. Stock 0: this condition is off. Effect: raise = purge is blocked at low speed Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x245F8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E8" flags="0x0">
    <title>Purge Enable - First Purge Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: lowest vehicle speed for the first purge of a trip, used only until the engine has run longer than the waiver run time. Stock 15 km/h, but the waiver run time is 0, so it does not apply. Effect: raise = the first purge of a trip needs more road speed (only with a waiver run time above 0) Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x245FA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1E9" flags="0x0">
    <title>Purge Enable - Throttle to Unblock</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: once purge has been blocked, it is released when throttle is at or above this (or speed at or above its unblock value). Stock 0: this condition is off. Effect: raise = purge stays blocked up to more throttle Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x245FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1EA" flags="0x0">
    <title>Purge Enable - Throttle Below Which Purge Is Blocked</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: purge is blocked when throttle is below this or speed is below its block value. Stock 0: this condition is off. Effect: raise = purge is blocked at small throttle openings Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x245FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1EB" flags="0x0">
    <title>Purge Enable - MAP On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: purge may switch on only with manifold pressure above this. Stock 14 kPa. Effect: raise = purge needs more manifold pressure to switch on Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24600" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1EC" flags="0x0">
    <title>Purge Enable - MAP Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: purge switches off when manifold pressure is at or below this. Stock 12 kPa. Effect: raise = purge switches off at a higher manifold pressure Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24602" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1ED" flags="0x0">
    <title>Purge Enable - First Purge Airflow Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: lowest engine airflow for the first purge of a trip, used only until the engine has run longer than the waiver run time. Stock 8 g/s, but the waiver run time is 0, so it does not apply. Effect: raise = the first purge of a trip needs more airflow (only with a waiver run time above 0) Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24604" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1EE" flags="0x0">
    <title>LTFT Purge Cell Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: commanded purge at or above this selects the purge set of trim cells (0 to 20); below it the non purge set (21 to 38) is used. Stock 2.1 %. Effect: raise = the non purge cells are used up to a higher purge level Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24AE0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1EF" flags="0x0">
    <title>LTFT Floor During Enrichment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: lowest long term trim applied while enrichment is requested. Stock 1.0, so a trim that removes fuel is not applied during enrichment. Effect: lower = a fuel-removing long term trim is also applied during enrichment Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24AFC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1F0" flags="0x0">
    <title>Purge Learned Memory Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: lowest value of the purge learned memory (the extra correction learned for canister purge; 1.0 = none). Stock 0.82. Effect: raise = less fuel can be removed for purge vapour Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24AFE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1F1" flags="0x30">
    <title>LTFT Learn Step - Idle and Closed Throttle Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: size of one learn step in the idle and closed throttle cells. Stock 0.40 % in each. Effect: raise = these cells learn in larger steps Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>cell</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="idle stopped, Park / Neutral, A/C off, purge on" />
      <LABEL index="1" value="idle stopped, in gear, A/C off, purge on" />
      <LABEL index="2" value="idle stopped, Park / Neutral, A/C on, purge on" />
      <LABEL index="3" value="idle stopped, in gear, A/C on, purge on" />
      <LABEL index="4" value="closed throttle moving, purge on" />
      <LABEL index="5" value="idle stopped, purge off" />
      <LABEL index="6" value="closed throttle moving, purge off" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24B16" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1F2" flags="0x0">
    <title>Purge Learned Memory Step Up</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: amount the purge learned memory moves back toward 1.0 per learn step when the mixture is lean in a purge cell. Stock 1.0 %. Effect: raise = the purge correction is removed faster Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24B24" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1F3" flags="0x0">
    <title>Purge Learned Memory Step Down</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: amount the purge learned memory drops per learn step when the mixture is rich and the purge cell has reached its learn-down limit. Stock 1.0 %. Effect: raise = the purge correction is learned faster Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24B26" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x1F4" flags="0x30">
    <title>LTFT Learn Step - Purge Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: size of one learn step in the 16 grid cells used with purge on, by engine speed zone and MAP zone. Stock 0.40 % in each. Effect: raise = these cells learn in larger steps Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>engine speed zone</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="up to 100 rpm" />
      <LABEL index="1" value="100 to 6000 rpm" />
      <LABEL index="2" value="6000 to 6500 rpm" />
      <LABEL index="3" value="above 6500 rpm" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>MAP zone</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="up to 5 kPa" />
      <LABEL index="1" value="5 to 60 kPa" />
      <LABEL index="2" value="60 to 110 kPa" />
      <LABEL index="3" value="above 110 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24B28" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1F5" flags="0x30">
    <title>LTFT Learn Step - Non Purge Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: size of one learn step in the 16 grid cells used with purge off, by engine speed zone and MAP zone. Stock 0.40 % in each. Effect: raise = these cells learn in larger steps Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>engine speed zone</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="up to 100 rpm" />
      <LABEL index="1" value="100 to 6000 rpm" />
      <LABEL index="2" value="6000 to 6500 rpm" />
      <LABEL index="3" value="above 6500 rpm" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>MAP zone</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="up to 5 kPa" />
      <LABEL index="1" value="5 to 60 kPa" />
      <LABEL index="2" value="60 to 110 kPa" />
      <LABEL index="3" value="above 110 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24B48" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x1F6" flags="0x30">
    <title>LTFT Purge Cells - Learn Down Limit per Trip</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim, purge cells 0 to 20: how far below its stored value a cell may learn during one trip. Once a cell is at that limit, further rich correction goes to the purge learned memory instead. Stock 18 % (13 % in cells 16 to 20). Effect: raise = a purge cell may learn further down in one trip before the purge learned memory takes over Evidence: ledger:E1107</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>21</indexcount>
      <units>cell</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24B68" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="21" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x1F7" flags="0x0">
    <title>LTFT Store - Coolant Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: the non purge cells are copied to the stored (keep-alive) values only below this coolant temperature. Stock 120 C. Effect: raise = learned values are stored at higher coolant temperature Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24BDC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1F8" flags="0x0">
    <title>LTFT Store - Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: and only above this coolant temperature. Stock 40 C. Effect: lower = learned values are stored on a colder engine Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24BDE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1F9" flags="0x0">
    <title>LTFT Store - Maximum, Non Purge Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: highest value stored for the non purge cells. Stock 1.25. Effect: raise = a larger fuel-adding trim can be stored Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24BE0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1FA" flags="0x0">
    <title>LTFT Store - Minimum, Idle Non Purge Cell</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: lowest value stored for the idle non purge cell. Stock 0.85. Effect: lower = a larger fuel-removing trim can be stored Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24BE2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1FB" flags="0x0">
    <title>LTFT Store - Minimum, Closed Throttle Non Purge Cell</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: lowest value stored for the closed throttle moving non purge cell. Stock 0.85. Effect: lower = a larger fuel-removing trim can be stored Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24BE4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1FC" flags="0x0">
    <title>LTFT Store - Minimum, Non Purge Grid Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: lowest value stored for the 16 non purge grid cells. Stock 0.85. Effect: lower = a larger fuel-removing trim can be stored Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24BE6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1FD" flags="0x0">
    <title>LTFT Store - Maximum, Purge Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: highest value stored for the purge cells. Stock 1.25. Effect: raise = a larger fuel-adding trim can be stored Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24BE8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1FE" flags="0x0">
    <title>LTFT Store - Minimum, Purge Cells</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: lowest value stored for the purge cells. Stock 0.85. Effect: lower = a larger fuel-removing trim can be stored Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24BEA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x1FF" flags="0x0">
    <title>Purge Learned Memory Recovery Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: amount the purge learned memory is moved back toward 1.0 at each start of a full fuel cut. Stock 10 %. Effect: raise = the purge correction recovers faster on deceleration Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24BEC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x200" flags="0x0">
    <title>LTFT MAP Change Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: filter on the manifold pressure used to measure the MAP change for the follow rate curve. Stock 1.0 (no filtering). Effect: lower = the MAP change is measured against a slower moving average Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24BEE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x201" flags="0x0">
    <title>LTFT Learn Follow Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: a cell learns only while the applied long term trim is within this of the cell value. Stock 5 %. Effect: raise = learning continues while the applied trim is further from the cell value Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24C04" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x202" flags="0x0">
    <title>Rear O2 Trim - Learn Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: the learned switch point offset is updated only at or above this coolant temperature. Stock 80 C. Effect: raise = the offset is learned only on a warmer engine Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24C08" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x203" flags="0x0">
    <title>Rear O2 Trim - Rear O2 Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: filter on the rear oxygen sensor voltage used by this trim; each 100 ms the filtered value moves this fraction of the way to the new reading. Stock 0.05. Effect: raise = the trim follows the rear sensor faster Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24C0A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x204" flags="0x0">
    <title>Rear O2 Trim - Learn Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: amount the learned switch point offset moves per learn interval. Stock 0.19 mV. Effect: raise = the offset is learned faster Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24C38" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x205" flags="0x0">
    <title>Rear O2 Trim - Rear O2 Rate Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: filter on the rear oxygen sensor signal used to measure how fast it is moving (the input of the adder by rear O2 rate). Stock 0.10 per 100 ms. Effect: raise = the rate input reacts faster Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24C40" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x206" flags="0x0">
    <title>Rear O2 Trim - Adder Idle Throttle Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: the idle factor applies only with the throttle area above the idle area below this (and below the idle speed limit). Stock 1.5 %. Effect: raise = the idle factor also applies with the throttle a little open Evidence: ledger:E1107</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24C44" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x207" flags="0x0">
    <title>Rear O2 Trim - Adder Idle Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: factor applied to the adder by rear O2 voltage at idle (low throttle and below the idle speed limit). Stock 0.80. Effect: raise = more of the adder is applied at idle Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24C46" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x208" flags="0x0">
    <title>Rear O2 Trim - Adder Idle Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: the idle factor applies below this vehicle speed. Stock 3 km/h. Effect: raise = the idle factor applies up to a higher speed Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24C48" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x209" flags="0x0">
    <title>Rear O2 Trim - Sensor Active Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: the rear sensor counts as active once its filtered voltage has been outside the not-active band for this long in total. Stock 1 s. Effect: raise = the rear sensor must show activity longer before the trim works Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24D94" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>25.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x20A" flags="0x0">
    <title>Rear O2 Trim - Not Active Band, High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: upper edge of the rear sensor not-active band; a reading at or above it counts toward the active time. Stock 550 mV. Effect: raise = a richer reading is needed to count as activity Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24D96" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x20B" flags="0x30">
    <title>Closed Loop Trim Jump - Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. These two values are the jump in closed-throttle idle: first while the O2 reads lean (trim steps up), second while it reads rich (trim steps down). Stock 0.40 % each. Effect: raise = bigger trim step at each O2 switch Evidence: ledger:E0433, ledger:E0903</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>O2 state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="lean" />
      <LABEL index="1" value="rich" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24DE8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x20C" flags="0x30">
    <title>Closed Loop Trim Jump - Off Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. These two values are the jump off idle: first while the O2 reads lean, second while it reads rich. Stock 0.40 % each. Effect: raise = bigger trim step at each O2 switch Evidence: ledger:E0433, ledger:E0903</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>O2 state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="lean" />
      <LABEL index="1" value="rich" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24DEC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x20D" flags="0x30">
    <title>Closed Loop Trim Jump - Unused Modes (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel (front O2): short-term trim steps by a fixed jump each time the O2 switch delay runs out, leaner when the O2 reads rich and richer when it reads lean, and adds a proportional offset of the same sign that grows with airflow and with how far the O2 is past its switch point. Inactive on the stock calibration: these jumps belong to closed-loop modes the mode selector never chooses with stock values. Effect: no effect on the stock calibration Evidence: ledger:E0433, ledger:E0903</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>12</indexcount>
      <units>mode / O2 state</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24DD0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="12" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x20E" flags="0x0">
    <title>Closed Loop Low Baro Mode - Barometric Pressure Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): below this barometric pressure the short term trim uses its second set of steps and delays (the mode 2 values of the unused modes items). Stock 0 kPa: never. Effect: raise = the second set is used below that barometric pressure Evidence: ledger:E1107</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24DF8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x20F" flags="0x0">
    <title>Closed Loop Coolant Window Mode - Coolant Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel, coolant window mode: the short term trim uses a separate set of gains while coolant is inside a window and the engine has run for less than a set time. This is the lower edge of the window: coolant must be above it. Stock 138 C. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: lower = the window starts at a lower coolant temperature Evidence: ledger:E1134</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E06" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x210" flags="0x0">
    <title>Closed Loop Coolant Window Mode - Coolant Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel, coolant window mode: the short term trim uses a separate set of gains while coolant is inside a window and the engine has run for less than a set time. This is the upper edge of the window: coolant must be below it. Stock 140 C. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = the window reaches a higher coolant temperature Evidence: ledger:E1134</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E08" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x211" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling - Cold Coolant Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this coolant temperature the cold Proportional Term Ceiling Factors are used in 1st gear and in 2nd, Neutral, Reverse and Park. Stock 45.5 C. Effect: raise = the cold factors are used up to a higher coolant temperature Evidence: ledger:E0436, ledger:E1134, ledger:E1216</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E0A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>C</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x212" flags="0x0">
    <title>STFT Idle Return Reset - Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: the idle return reset works only at or above this coolant temperature. Stock 50 C. Effect: raise = the reset needs a warmer engine Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E0C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x213" flags="0x0">
    <title>STFT Idle Return Reset - Arm RPM Above Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: the idle return reset is armed when engine speed is more than this above desired idle. Stock 200 rpm. Effect: raise = the reset is armed only from a higher engine speed Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E0E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x214" flags="0x0">
    <title>STFT Idle Return Reset - Fire RPM Above Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: once armed, the reset fires when engine speed comes back to less than this above desired idle with the trim integrator below the reset threshold: the integrator is set to 1.0. Stock 10 rpm. Effect: raise = the reset fires earlier on the way down to idle Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E10" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x215" flags="0x0">
    <title>Closed Loop Proportional Term - Multiplier Before Closed Loop Is Enabled</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim before closed loop is enabled: once the O2 sensor is ready but the coolant and run time conditions for closed loop are not yet met, the O2 trim already runs on top of open loop fuelling, and its proportional term is multiplied by this. Stock 1.0. Effect: lower = a gentler O2 correction in the phase before closed loop Evidence: ledger:E1140</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E12" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x216" flags="0x0">
    <title>STFT Integrator Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: highest value of the trim integrator (1.0 = no correction). Stock 1.31. Effect: raise = short term trim can add more fuel Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E2E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x217" flags="0x0">
    <title>STFT Integrator Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: lowest value of the trim integrator. Stock 0.80. Effect: lower = short term trim can remove more fuel Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E30" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x218" flags="0x0">
    <title>STFT Open Loop Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: highest integrator value kept while open loop. Stock 1.0; with the open loop minimum also 1.0 the integrator is reset to 1.0 whenever the system goes open loop. Effect: raise = a fuel-adding trim is kept through open loop Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E32" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x219" flags="0x0">
    <title>STFT Idle Return Reset - Integrator Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: the idle return reset fires only when the trim integrator is below this. Stock 1.0. Effect: lower = only a larger fuel-removing trim is reset on the return to idle Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E34" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x21A" flags="0x0">
    <title>STFT Open Loop Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: lowest integrator value kept while open loop. Stock 1.0. Effect: lower = a fuel-removing trim is kept through open loop Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E36" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x21B" flags="0x30">
    <title>Closed Loop O2 Filter Gain - Rich / Lean Decision</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): filter on the O2 voltage that is compared with the switch point to decide rich or lean, by airflow. Share of each new reading taken every 12.5 ms. Stock 0.5 at idle and 1.0 (no filtering) off idle. Effect: lower = the rich / lean decision reacts more slowly to the O2 sensor Evidence: ledger:E1126</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s used airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4.8" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="13.2" />
      <LABEL index="4" value="21.8" />
      <LABEL index="5" value="29.5" />
      <LABEL index="6" value="40.3" />
      <LABEL index="7" value="51.8" />
      <LABEL index="8" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24E92" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x21C" flags="0x0">
    <title>Closed Loop Slow-Sensor Tables - Response Time Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel, slow sensor tables: once the slow sensor tables are in use, this is added to the measured O2 response times before they are classed again, so the tables are not left on a marginal improvement. Stock 3.9 ms. Effect: raise = the slow sensor tables are kept for longer once selected Evidence: ledger:E1126</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x250CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ms</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>63999.023438</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1.024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x21D" flags="0x30">
    <title>Closed Loop Alternate Tables Map - O2 Lean (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this map would turn on the slow-sensor tables while the O2 reads lean, and it is all zero. Rows are the lean-to-rich response time and columns the rich-to-lean response time (the opposite of the rich map). Effect: no effect on the stock calibration Evidence: ledger:E0433, ledger:E0904, ledger:E1126</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rich-to-lean time (ms)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="29" />
      <LABEL index="1" value="39" />
      <LABEL index="2" value="49" />
      <LABEL index="3" value="59" />
      <LABEL index="4" value="69" />
      <LABEL index="5" value="79" />
      <LABEL index="6" value="89" />
      <LABEL index="7" value="99" />
      <LABEL index="8" value="109" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>lean-to-rich time (ms)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="29" />
      <LABEL index="1" value="39" />
      <LABEL index="2" value="49" />
      <LABEL index="3" value="59" />
      <LABEL index="4" value="69" />
      <LABEL index="5" value="79" />
      <LABEL index="6" value="89" />
      <LABEL index="7" value="99" />
      <LABEL index="8" value="109" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x250D6" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flag</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x21E" flags="0x30">
    <title>Closed Loop Alternate Tables Map - O2 Rich</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-loop fuel, slow-sensor tables: when the front O2 is measured slow going rich-to-lean but fast going lean-to-rich, closed loop uses this alternate set while the O2 reads rich (see Closed Loop Alternate Tables Map). This map turns on the slow-sensor tables while the O2 reads rich (1 = on), by measured rich-to-lean time (rows) and lean-to-rich time (columns), about 10 ms per step from 29 ms. Stock on only when rich-to-lean is 89 ms or slower and lean-to-rich is much faster. Effect: 1 = slow-sensor tables on for that response Evidence: ledger:E0433, ledger:E0904</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>lean-to-rich time (ms)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="29" />
      <LABEL index="1" value="39" />
      <LABEL index="2" value="49" />
      <LABEL index="3" value="59" />
      <LABEL index="4" value="69" />
      <LABEL index="5" value="79" />
      <LABEL index="6" value="89" />
      <LABEL index="7" value="99" />
      <LABEL index="8" value="109" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rich-to-lean time (ms)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="29" />
      <LABEL index="1" value="39" />
      <LABEL index="2" value="49" />
      <LABEL index="3" value="59" />
      <LABEL index="4" value="69" />
      <LABEL index="5" value="79" />
      <LABEL index="6" value="89" />
      <LABEL index="7" value="99" />
      <LABEL index="8" value="109" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2512E" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flag</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x21F" flags="0x0">
    <title>Per Cylinder Fuel Multipliers - Switch (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per cylinder fuel multipliers: 0 = not applied (stock). 1 = applied at all engine speeds; fuel is then also calculated per cylinder above about 5000 rpm, where stock uses one value for all cylinders. Any other value = applied below about 5000 rpm only. Note that the stock multiplier values are 0.9995, not exactly 1. Effect: 1 = the per cylinder multipliers take effect Evidence: ledger:E1141</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x252A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>code</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x220" flags="0x0">
    <title>Fuel Injected Since Start - Count Scale (do not edit)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sets how much injected fuel one count of the fuel injected since start value represents; that value is the row input of the start-up open-loop fuel tables. Stock 22.28 mg per count (65,535 counts = 1.46 kg, after which the count wraps). Changing it rescales those tables&#x27; fuel axis, so leave it at stock. Effect: do not edit: it changes the meaning of the start-up fuel table axis Evidence: ledger:E0436, ledger:E1468</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26616" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>mg per count</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>32.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/134217728"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x221" flags="0x0">
    <title>Transient Fuel - Wall Film Mass Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transient fuel: largest fuel mass the wall film model of a cylinder may hold. Stock 2048 mg, the largest value the film can take anyway, so it does not limit. Effect: lower = the modelled wall film is capped, which shortens tip-in and tip-out corrections Evidence: ledger:E1139</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2661A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>mg</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>2047.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x222" flags="0x0">
    <title>Acceleration Fuel Adder - Fuel Rise Minimum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra fuel on acceleration: the calculated fuel of a cylinder must rise by at least this from one injection to the next before the rise adds to the adder. Stock 2.75 mg. Dormant on the stock calibration: the adder gain curve is all zero, so there is no adder. Effect: raise = only larger jumps in fuel demand add extra fuel Evidence: ledger:E1139</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2661C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mg</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x223" flags="0x0">
    <title>Acceleration Fuel Adder - Fuel Fall That Clears It (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra fuel on acceleration: when the calculated fuel of a cylinder falls by more than this from one injection to the next (a negative value), the adder is cleared. Stock -3 mg. Dormant on the stock calibration: the adder gain curve is all zero, so there is no adder. Effect: more negative = the adder survives larger drops in fuel demand Evidence: ledger:E1139</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2661E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mg</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x224" flags="0x0">
    <title>First-Run Mode - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First-run mode runs only during the first 12 s of engine running recorded by the PCM (kept through power-off), with a stored flag set, the mode enable set and start-up coolant inside the coolant window. This switch allows it (1) or not (0). Stock 1. Effect: 0 = first-run mode never runs Evidence: ledger:E0436, ledger:E1227, ledger:E1577</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x26E12" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>switch</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x225" flags="0x0">
    <title>Hot-Restart Fuel - Minimum Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot-restart fuel gate: a latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, the Open Loop Hot-Restart Gain table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. This is the minimum coolant temperature. Stock 95 C. Effect: raise = hot-restart fuel needs a hotter engine and drops out soon...</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x298E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x226" flags="0x0">
    <title>Hot-Restart Fuel - Latch Intake Air</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot-restart fuel gate: a latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, the Open Loop Hot-Restart Gain table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. This is the latch intake air threshold. Stock 38 C. Effect: raise = hotter intake air needed to arm a hot restart Evidence: le...</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x298F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x227" flags="0x0">
    <title>Hot-Restart Fuel - Maximum Soak Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot-restart fuel gate: a latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, the Open Loop Hot-Restart Gain table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. This is the maximum engine-off soak time. Stock 3000 s (50 minutes). Effect: raise = longer stops still get hot-restart fuel E...</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x298F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x228" flags="0x0">
    <title>Hot-Restart Fuel - Minimum Soak Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot-restart fuel gate: a latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, the Open Loop Hot-Restart Gain table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. This is the minimum engine-off soak time. Stock 600 s (10 minutes). Effect: lower = shorter stops also get hot-restart fuel Ev...</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x298F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x229" flags="0x0">
    <title>O2 Sensor Ready - Resting Band High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor ready logic: a reading above this counts as sensor activity. Together with the band low value it marks the resting band a cold, inactive sensor sits in. Stock 550 mV. Effect: lower = a smaller rich swing counts as activity Evidence: ledger:E1005</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x298FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x22A" flags="0x0">
    <title>O2 Sensor Ready - Resting Band Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor ready logic: a reading below this counts as sensor activity. Stock 350 mV. Effect: raise = a smaller lean swing counts as activity Evidence: ledger:E1005</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x298FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x22B" flags="0x0">
    <title>O2 Sensor Ready - Coolant Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor ready logic: once the sensors are ready, coolant may drop this far below the O2 ready coolant curve before they are un-flagged. Stock 3 C. Effect: raise = ready is kept through a larger coolant drop Evidence: ledger:E1005</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x29948" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x22C" flags="0x0">
    <title>O2 Sensor Ready - Inactive Time To Un-Flag</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor ready logic: a ready sensor is un-flagged after its reading has stayed inside the resting band for longer than this. Stock 10 s. Effect: raise = a sensor can sit in the resting band longer before it is un-flagged Evidence: ledger:E1005</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2994A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x22D" flags="0x0">
    <title>Idle A/C - Engage Pre-Ramp Torque Ratio Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: with the throttle open, idle air is pre-ramped before the A/C clutch engages only when A/C compressor torque is at or below this share of engine torque. Stock 0.45. Effect: raise = the pre-ramp also happens at lower engine torque Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29C72" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x22E" flags="0x0">
    <title>Idle A/C - Engage Pre-Ramp Torque Ratio Maximum, Converter Clutch On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: same torque ratio limit, used while the torque converter clutch is applying or applied. Stock 0.45. Effect: raise = the pre-ramp also happens at lower engine torque Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29C76" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x22F" flags="0x0">
    <title>Idle A/C - Throttle Closed Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: throttle at or below this counts as closed for the A/C idle air sequence. Stock 2.0 %. Effect: raise = a more open throttle still counts as closed Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29C78" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x230" flags="0x0">
    <title>Idle A/C - Throttle Closed Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: the closed throttle flag clears only above the threshold plus this. Stock 0.7 %. Effect: raise = the closed throttle flag holds further into the throttle Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29C7A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x231" flags="0x0">
    <title>Idle A/C - Release Adder Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: the idle air adder for A/C clutch release runs only with the throttle closed and below this speed. Stock 3 km/h. Effect: raise = the release adder also runs at higher speed Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29C7C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x232" flags="0x0">
    <title>Idle A/C - Time Between Engage Sequences</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: minimum time after one engage sequence has ended before the next closed-throttle engage sequence. Stock 1 s. Effect: raise = repeated A/C engagements are spaced further apart Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29C7E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x233" flags="0x0">
    <title>Idle Airflow Learn - Key-Off Save Step Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn: at key-off the saved value moves toward the value learned on this trip by at most this much. Stock 0.25 g/s per key cycle. Effect: raise = the saved learn follows each trip faster Evidence: ledger:E1106</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29CBE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x234" flags="0x0">
    <title>Idle Airflow Integral - Step Down Throttle Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: the airflow integral may step down only while the throttle area above the idle area is below this. Stock 0.70 %. Effect: raise = the integral may also step down with the throttle a little further open Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29CF2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x235" flags="0x0">
    <title>Idle Air - Coolant Fallback Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air control: when the coolant reading is at or below this, the idle module uses the highest coolant temperature seen instead of the sensor reading. Stock -39 C (a failed-open sensor). Effect: raise = the fallback takes over at warmer readings Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A0AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x236" flags="0x0">
    <title>Idle Key-Off - Throttle Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After key-off the idle throttle area is held at the key-off area value for this time, then idle control stops. Stock 2 s. Effect: raise = the key-off throttle position is held longer Evidence: ledger:E1106</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A1AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x237" flags="0x0">
    <title>Idle Disturbance Latch - RPM Change per Sample</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: rpm change between two 12.5 ms samples above which the disturbance latch sets. Stock 8191.9 rpm: off. The disturbance latch: in closed loop idle speed control with the throttle closed, a sudden rpm change above a speed threshold puts the idle controller back in its moving mode for a time. Effect: lower = smaller rpm jumps set the latch Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A224" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x238" flags="0x0">
    <title>Idle Disturbance Latch - Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: time the disturbance latch keeps the moving mode on. Stock 0 s. The disturbance latch: in closed loop idle speed control with the throttle closed, a sudden rpm change above a speed threshold puts the idle controller back in its moving mode for a time. Effect: raise = the moving mode is held longer after a disturbance Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A230" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x239" flags="0x0">
    <title>Idle Air - RPM Control Entry Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air control: idle speed control is entered only this long after the throttle follower has finished. Stock 0.05 s. Effect: raise = idle speed control takes over later after a throttle release Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A232" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x23A" flags="0x0">
    <title>Decel Fuel Cut Idle Air - Fade Out Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air during decel fuel cut: once fuel cut is no longer active the extra idle air moves back toward 0 by this much every 12.5 ms. Stock 0.0098 g/s (0.78 g/s per second). Effect: raise = the fuel cut idle air is removed faster after fuel cut Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A964" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x23B" flags="0x30">
    <title>Cold Start High Idle - Idle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold start high idle: desired idle speed while the cold start high idle is active, in gear and in Park / Neutral. Stock 900 rpm for both. Effect: raise = higher idle after a very cold start Evidence: ledger:E1112</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>load state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="in gear" />
      <LABEL index="1" value="Park / Neutral" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2ABE2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x23C" flags="0x30">
    <title>Idle Cold Request - Until Coolant Reaches</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cold idle request stays active until the highest coolant temperature since start reaches this. Stock 0 C. Cold idle request: until the engine coolant has reached the limit at least once since start, desired idle is raised to at least the request speed (desired idle is the highest of all idle speed requests). Effect: raise = the cold idle request lasts until a warmer engine Evidence: ledger:E0436, ledger:E1508</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>1</indexcount>
      <units>field</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B0AE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="1" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x23D" flags="0x0">
    <title>Desired Idle Requests - Hold Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Desired idle: an idle request whose condition has ended (A/C, cold start and others) stays held while the vehicle is slower than this, so idle speed does not drop while stopped. Stock 8 km/h. Effect: raise = finished idle requests are held up to a higher road speed Evidence: ledger:E1112</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B0B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x23E" flags="0x0">
    <title>Per Cylinder Knock Retard Step Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Caps how much knock retard the computer can add to one cylinder in a single correction, before that amount is added onto the cylinder&#x27;s running knock retard. Stock is 5.0 degrees. It does not cap the total retard a cylinder can carry, only the size of each individual addition. Effect: raise = a knocking cylinder&#x27;s retard can jump by a larger amount in a single correction (faster buildup); lower = each correction adds less, so retard builds more slowly. Stock is 5.0 degrees per correction. Evidence: ledger:E0772, ledger:E0798</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2B6C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x23F" flags="0x0">
    <title>Burst Knock Retard - Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Burst knock retard sequence: a quick rise in cylinder airmass starts a burst of spark retard (sized by the burst retard curves and the learned multiplier). After the delay the retard is applied, held for the hold count, then removed in equal steps over the decay count. Counts are updates of the burst retard routine. This is the delay before the retard is applied. Stock 0 (applied at once). Effect: raise = the burst retard comes in later Evidence: ledger:E0870</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2B910" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x240" flags="0x0">
    <title>Burst Knock Retard Multiplier - Step Up</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Burst knock retard learned multiplier: two learned multipliers (1.0 = full burst retard) scale the burst knock retard. One event raises the active multiplier by the step up, another lowers it by the step down, and it is never allowed below the floor. Stock floor is 1.0, the top of the range, so on the stock calibration the multipliers stay at 1.0 and nothing is learned; lowering the floor lets burst retard learn down. This is the step up. Stock 0.05. Effect: raise = the multiplier climbs back toward 1.0 faster Evidence: ledger:E0869</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2B92C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x241" flags="0x0">
    <title>Burst Knock Retard Multiplier - Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Burst knock retard learned multiplier: two learned multipliers (1.0 = full burst retard) scale the burst knock retard. One event raises the active multiplier by the step up, another lowers it by the step down, and it is never allowed below the floor. Stock floor is 1.0, the top of the range, so on the stock calibration the multipliers stay at 1.0 and nothing is learned; lowering the floor lets burst retard learn down. This is the floor. Stock 1.0 (learning inert). Effect: lower = burst retard can learn down to this fraction Evidence: ledger:E0869</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2B932" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x242" flags="0x0">
    <title>Knock Learn Rate - MAP Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is one of the five weights (relative; only the ratios matter). Stock 1.0. Effect: raise = this curve counts for more in the average Evidence: ledger:E0193, ledger:E0871</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2BAC0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x243" flags="0x0">
    <title>Airmass Temperature Correction Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A gain constant in the airmass and barometric pressure correction chain, applied to the combined intake air and coolant temperature correction term. Stock is a gain of exactly 1.0, meaning the term currently passes through unscaled. Effect: Raising it above 1.0 would amplify the temperature correction term&#x27;s effect on the airmass calculation; lowering it below 1.0 would reduce that effect. Evidence: ledger:E0772, ledger:E0805</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2BD32" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain (unitless)</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x244" flags="0x0">
    <title>Airflow Model Learn Freeze - Release Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow model ratio learn: a freeze latch on the learn is released once throttle position is at or above this. Stock 0.5 %. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this software Evidence: ledger:E0192, ledger:E0780, ledger:E0858, ledger:E1136</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2BD94" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x245" flags="0x0">
    <title>VE Transient Mode - MAP Band Split</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow source switching: the PCM normally uses the MAF airflow and, during a manifold pressure transient, switches to the VE (speed density) airflow times a learned MAF to VE ratio. It switches over when MAP keeps moving by more than the MAP change threshold per update (two updates in a row), or when MAP moves more than that over two updates while the throttle area moves the same way by more than the area change threshold; it switches back once the MAP change over one, two and three updates is at or below the MAP change threshold. The high band thresholds apply at or above the MAP split or the RPM split. At or above this MAP...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C980" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x246" flags="0x0">
    <title>VE Transient Mode - Window Exit Length (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of model updates a window must pass before the transient mode may end and the window starts again (stock 9). Part of the window check of the volumetric efficiency transient mode, which runs only when its throttle gate is open; on the stock calibration that gate is closed, so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0780, ledger:E0854, ledger:E1429</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C994" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x247" flags="0x30">
    <title>Airmass Predictor Region Map</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airmass predictor region: the PCM predicts cylinder airmass a little ahead of the MAF reading, with a separate set of predictor coefficients per region. The region is an idle window (low throttle, low engine speed, moderate vacuum) or one of 16 cells from four engine speed bands by four MAP bands. Region code by MAP band (rows) and engine speed band (columns), shown raw. Reference only: the codes must match the predictor coefficients. DO NOT EDIT. Effect: reference only (airmass predictor) Evidence: ledger:E0323, ledger:E0780, ledger:E0864, ledger:E0899</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C9D2" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>region</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x248" flags="0x30">
    <title>Airmass Predictor Engine Speed Band Splits</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airmass predictor region: the PCM predicts cylinder airmass a little ahead of the MAF reading, with a separate set of predictor coefficients per region. The region is an idle window (low throttle, low engine speed, moderate vacuum) or one of 16 cells from four engine speed bands by four MAP bands. Leave these at stock unless the predictor coefficients are recalibrated with them. Engine speed splits between the four bands. Stock 1000, 2000, 3000 rpm. Effect: moves which predictor coefficient set applies Evidence: ledger:E0323, ledger:E0864</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C9F2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x249" flags="0x30">
    <title>Airmass Predictor MAP Band Thresholds</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airmass predictor region: the PCM predicts cylinder airmass a little ahead of the MAF reading, with a separate set of predictor coefficients per region. The region is an idle window (low throttle, low engine speed, moderate vacuum) or one of 16 cells from four engine speed bands by four MAP bands. Leave these at stock unless the predictor coefficients are recalibrated with them. MAP thresholds between the four MAP bands (rows: lowest, middle, top split), per engine speed band (columns). Stock 26 / 24 / 22 / 22, 59, 88 kPa. Effect: moves which predictor coefficient set applies Evidence: ledger:E0323, ledger:E0864</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C9F8" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x24A" flags="0x0">
    <title>Airmass Predictor Engine Speed Band Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airmass predictor region: the PCM predicts cylinder airmass a little ahead of the MAF reading, with a separate set of predictor coefficients per region. The region is an idle window (low throttle, low engine speed, moderate vacuum) or one of 16 cells from four engine speed bands by four MAP bands. Leave these at stock unless the predictor coefficients are recalibrated with them. Engine speed hysteresis: the region keeps its engine speed band until speed moves this far past either band edge. Stock 50 rpm. Effect: raise = the predictor region changes speed band less often Evidence: ledger:E0323, ledger:E0772, ledger:E0864, ledg...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2CA10" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x24B" flags="0x0">
    <title>Starter - Crank Request Debounce Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The crank request from the ignition switch must be present for this long, in park or neutral, before the PCM engages the starter relay. Stock 0.05 s. Effect: raise = the key must be held in crank longer before the starter engages Evidence: ledger:E1024</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x204CC" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x24C" flags="0x0">
    <title>Starter - System Voltage OK Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter control: time the system voltage must have been above its minimum (6 V) before the starter may engage. Stock 0 s: no wait. Effect: raise = the starter engages only after the voltage has been up for that long Evidence: ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30206" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x24D" flags="0x0">
    <title>Starter - Minimum On Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once engaged, the starter relay stays on for at least this long before the key-released and crank time limit checks can turn it off (leaving park / neutral or the engine starting still turn it off at once). Stock 0.2 s. Effect: raise = the starter stays engaged longer after a brief key turn Evidence: ledger:E1024</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x30208" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x24E" flags="0x0">
    <title>Starter - Maximum Crank Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM turns the starter relay off after this much continuous cranking, and does not re-engage it until the key is released. Stock 15 s. Effect: raise = the starter may crank longer in one attempt Evidence: ledger:E1024</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x30216" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x24F" flags="0x0">
    <title>Starter Low-Voltage Hold - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter low-voltage hold: 1 lets the PCM keep the starter engaged through a voltage collapse below 4 V while cranking; 0 turns the feature off. Stock 1. Effect: 0 = the starter follows the key signal only Evidence: ledger:E1025</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x30218" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x250" flags="0x0">
    <title>Starter Low-Voltage Hold - Run Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter low-voltage hold: the hold is cancelled once engine run time is longer than this. Stock 1.0 s. Effect: raise = the hold can persist longer after the engine fires Evidence: ledger:E1025</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x30226" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x251" flags="0x0">
    <title>Starter Low-Voltage Hold - Cancel Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter low-voltage hold: the hold is cancelled when system voltage stays above 4 V but below this for the cancel time. Stock 6.0 V. Effect: raise = a higher sustained cranking voltage still cancels the hold Evidence: ledger:E1025</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x30228" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x252" flags="0x0">
    <title>Starter Low-Voltage Hold - Cancel Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter low-voltage hold: how long system voltage must stay between 4 V and the cancel voltage to cancel the hold. Stock 0.5 s. Effect: raise = the low voltage must last longer to cancel the hold Evidence: ledger:E1025</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x3022A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x253" flags="0x0">
    <title>Starter Low-Voltage Hold - Fuel Level Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter low-voltage hold: the hold is not used when the fuel level is at or below this (a held mode setting can override this). Stock 2 %. Effect: raise = the hold is dropped at higher fuel levels Evidence: ledger:E1036</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x3022C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x254" flags="0x0">
    <title>Traction Control - Reduction Detect Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control torque reduction: the requested torque counts as a reduction only when it is below this share of the torque the throttle would give now. Stock 0.98. Effect: lower = only a deeper torque request counts as a reduction Evidence: ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3027E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x255" flags="0x0">
    <title>Traction Control - Torque Request Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control torque reduction: share of each new reading of the torque request signal taken into its filtered value every 25 ms. Stock 0.5; 1.0 = no filtering. Effect: raise = the engine follows the torque request faster Evidence: ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30280" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x256" flags="0x0">
    <title>Torque Model - Engine Torque Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque model: share of each new value taken into the filtered engine torque values every 25 ms. Stock 0.25; 1.0 = no filtering. Effect: raise = the modelled engine torque follows changes faster Evidence: ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3031A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x257" flags="0x0">
    <title>Torque Reduction Cylinder Cut - Cylinders Added Back on a First Gear Shift</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque reduction with cylinder cut: cylinders added back to the fuelled count for a short time when traction control is reducing torque during a shift out of first gear. Stock 2. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = more cylinders are given back for that shift Evidence: ledger:E1133</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x31560" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cylinders</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x258" flags="0x0">
    <title>Torque Reduction Cylinder Cut - Shift Add-Back Time Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque reduction with cylinder cut: longest time the shift add-back stays on. Stock 0.5 s. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = the add-back may last longer Evidence: ledger:E1133</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x31562" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x259" flags="0x0">
    <title>Torque Reduction Cylinder Cut - Shift Add-Back Speed Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque reduction with cylinder cut: the shift add-back starts when the transmission input to output speed ratio falls below this during the shift. Stock 1.5. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = the add-back starts earlier in the shift Evidence: ledger:E1133</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x31564" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x25A" flags="0x0">
    <title>Torque Reduction Spark Retard - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque reduction: spark retard is only requested once the engine has run longer than this. Stock 5 s. Effect: raise = no torque reduction spark retard for longer after a start Evidence: ledger:E1130</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x31AD6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x25B" flags="0x0">
    <title>Torque Reduction Spark Retard - Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque reduction: spark retard is only requested above this engine speed. Stock 600 rpm. Effect: raise = no torque reduction spark retard at low engine speed Evidence: ledger:E1130</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x31AD8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x25C" flags="0x0">
    <title>Closed Throttle Flag - Set Below Commanded Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed throttle flag (used by the A/C compressor control to hold the compressor off just after the throttle closes): the flag sets when the commanded throttle area above the idle area is at or below this, and the measured throttle is also at or below its own limit. The flag clears again when the commanded value rises above this plus the release hysteresis. Stock 0.1 %. Effect: raise = the throttle counts as closed at a larger commanded opening Evidence: ledger:E1137</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31B4E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x25D" flags="0x30">
    <title>Knock Detection - Level Filter Multipliers During Knock</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: in a knock window where the cylinder knocked, its reference level filter is multiplied by the first value and its noise level filter by the second, so that knock itself is kept out of the levels. Stock 1.0 for the reference level (no change) and 0.01 for the noise level. Effect: lower = a knocking sample moves that level less Evidence: ledger:E1138</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>level</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="reference level" />
      <LABEL index="1" value="noise level" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31E3A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x25E" flags="0x0">
    <title>Knock Threshold Learn - Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock threshold learn: share of the gap to its target that the learned threshold factor of a cylinder closes after each knock window. Stock 0.0025. Effect: raise = the learned factor moves faster Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31E52" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x25F" flags="0x0">
    <title>Knock Threshold Learn - Factor Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock threshold learn: lowest value of the learned factor. The knock threshold of a cylinder is its reference level plus this factor times the threshold table value, so a lower factor makes knock detection more sensitive. Stock 0.70. Effect: raise = the learn can lower the knock threshold less, so knock detection stays less sensitive Evidence: ledger:E1131, ledger:E1138</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31E54" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x260" flags="0x0">
    <title>Knock Threshold Learn - Factor Maximum and Default</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock threshold learn: highest value of the learned factor, and the value every cylinder starts from when the stored factors are lost. Stock 1.00. Effect: raise = the learn may raise the knock threshold above the table value Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31E56" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x261" flags="0x0">
    <title>Knock Threshold Learn - Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock threshold learn: the learned factor is only updated above this engine speed. Stock 1500 rpm. Effect: raise = no learning at lower engine speed Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31E58" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x262" flags="0x0">
    <title>Knock Threshold Learn - Airmass Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock threshold learn: the learned factor is only updated above this cylinder airmass. Stock 0.32 g per cylinder. Effect: raise = no learning at lighter load Evidence: ledger:E1131</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31E5A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/cyl</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.095937</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x263" flags="0x30">
    <title>P1545 Circuit Check - Fault Count and Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Output circuit check P1545: the code sets once the first value&#x27;s number of faulted samples is reached; if the second value&#x27;s number of samples is reached first, the check passes and both counts start again. Stock 100 and 120. Effect: raise the first value = more faulted samples are needed to set the code; raise the second = each window is longer Evidence: ledger:E1058</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>value</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="fault samples to fail" />
      <LABEL index="1" value="window samples to pass" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34570" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x264" flags="0x0">
    <title>Crank Variation Learn - Attempt Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn: a learn request is refused once the number of learn attempts is above this. Stock 255 (no limit). Effect: lower = the learn can only be attempted this many times Evidence: ledger:E1081</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3457A" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>attempts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x265" flags="0x0">
    <title>Crank Variation Learn - Coolant Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn (the service procedure that clears P0315): the learn is refused while coolant is below this. Stock 65 degC. Effect: raise = the learn needs a warmer engine Evidence: ledger:E1040</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3457C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x266" flags="0x0">
    <title>Crank Variation Learn - RPM Rise Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn (the service procedure that clears P0315): sampling is abandoned if engine speed rises by more than this from one sample pass to the next. Stock 50 rpm. Effect: raise = a larger rpm rise is tolerated while sampling Evidence: ledger:E1040</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3457E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x267" flags="0x0">
    <title>Crank Variation Learn - Sampling RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn (the service procedure that clears P0315): samples are taken only while engine speed is above this; at or below it sampling ends. Stock 1500 rpm. Effect: raise = sampling ends at a higher engine speed Evidence: ledger:E1040</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34580" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x268" flags="0x0">
    <title>Crank Variation Learn - Sampling RPM Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn (the service procedure that clears P0315): once armed, samples are taken only while engine speed is at or below this. Stock 3800 rpm. Effect: raise = sampling starts at a higher engine speed Evidence: ledger:E1040</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34582" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x269" flags="0x0">
    <title>Catalyst Monitor - Stopped Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: vehicle speed at or below this counts as stopped. Stock 7 km/h. Effect: raise = the test also treats a slow roll as stopped Evidence: ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x26A" flags="0x0">
    <title>Catalyst Monitor Enable - Catalyst Temperature Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): the test is armed only while the modelled catalyst temperature is at or below this. Stock 700 C. Effect: lower = the test is skipped at lower catalyst temperatures Evidence: ledger:E0437, ledger:E0852, ledger:E0967, ledger:E1188</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>1023.984375</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/64"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x26B" flags="0x0">
    <title>Catalyst Monitor - Trim Averaging Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): before the fuel steps the short term fuel trim is averaged over whole O2 sensor switch cycles for at least this long. Stock 4 s. Effect: raise = the trim is averaged longer before the fuel steps Evidence: ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x26C" flags="0x0">
    <title>Catalyst Monitor - Trim Averaging Time Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): if the trim average is not complete after this long the test is abandoned. Stock 10 s. Effect: raise = the test waits longer for a usable trim average Evidence: ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x26D" flags="0x30">
    <title>Catalyst Monitor Enable - Average Short Term Trim Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): the short term fuel trim averaged over the trim sampling time must be at or above this for the test to go on (one value per catalyst; this truck uses the first). Stock 0.94. Effect: raise = a leaner average trim stops the test Evidence: ledger:E1082, ledger:E1188</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>catalyst</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x345F0" mmedelementsizebits="32" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>131071.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x26E" flags="0x30">
    <title>Catalyst Monitor Enable - Average Short Term Trim Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): the short term fuel trim averaged over the trim sampling time must be at or below this for the test to go on (one value per catalyst; this truck uses the first). Stock 1.06. Effect: lower = a richer average trim stops the test Evidence: ledger:E0437, ledger:E1082, ledger:E1188</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>catalyst</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x345F8" mmedelementsizebits="32" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>131071.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x26F" flags="0x0">
    <title>Catalyst Monitor - Purge Ramp Out Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): rate at which canister purge is ramped to zero when a test is armed. Stock 99 % per second. Effect: lower = purge is shut off more gradually before a test Evidence: ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34610" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% per s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>64997.613000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*0.9918"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x270" flags="0x0">
    <title>Catalyst Monitor - Purge Ramp In Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): rate at which canister purge is brought back after a test. Stock 397 % per second (back within about a quarter of a second). Effect: lower = purge returns more gradually after a test Evidence: ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34612" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% per s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>64997.613000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X*0.9918"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x271" flags="0x0">
    <title>Catalyst Monitor Enable - Short Term Trim Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): the short term fuel trim must stay at or above this during the test, otherwise the attempt is dropped (1.0 = no correction). Stock 0.88. Effect: raise = the test is dropped with less lean correction Evidence: ledger:E1082, ledger:E1188</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34614" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x272" flags="0x0">
    <title>Catalyst Monitor Enable - Short Term Trim Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): the short term fuel trim must stay at or below this during the test, otherwise the attempt is dropped (1.0 = no correction). Stock 1.12. Effect: lower = the test is dropped with less rich correction Evidence: ledger:E1082, ledger:E1188</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34616" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x273" flags="0x30">
    <title>Catalyst Monitor - Fuel Step Airflow Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow points of the two catalyst monitor fuel step curves. Stock 3 to 12 g/s. The curves that use it are spread over these points, so moving them re-spaces those curves; keep the point count and keep the points rising. Effect: moving a point shifts where the fuel step curves change Evidence: ledger:E1002</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34620" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x274" flags="0x30">
    <title>Catalyst Monitor - Second Step Upstream Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: the test is thrown away if the upstream O2 sensor takes longer than this to respond to the second fuel step. Stock 2.0 s. Effect: raise = a slower upstream response is still accepted Evidence: ledger:E1000</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x346B2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x275" flags="0x30">
    <title>Catalyst Monitor - Fast Pass Margin</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: while every test so far has beaten the reference by more than this margin, the monitor counts as having enough tests to pass at once. The value is the shortfall limit, so it is negative. Stock -0.6 s (storage time more than 0.6 s above the reference). Effect: more negative = a larger margin is needed for the fast pass Evidence: ledger:E1021</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>bank</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x346BE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>-204.800000</min>
      <max>204.793750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x276" flags="0x30">
    <title>Catalyst Monitor - Fail Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: P0420 sets when the filtered shortfall of storage time below the reference is greater than this. Stock 0.28 s. Effect: raise = the catalyst must fall further short before the code sets Evidence: ledger:E1021</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>bank</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x346CE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x277" flags="0x0">
    <title>P0125 / P0128 Check - Airflow Counted Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: airflow below this is not counted when the checks add up the air the engine has drawn since start. Stock 7 g/s. Effect: raise = low airflow (idling) no longer counts toward the required air mass Evidence: ledger:E0776, ledger:E0805, ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35186" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x278" flags="0x0">
    <title>Coolant Temperature Rise Rate Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The maximum amount the reported, filtered engine coolant temperature is allowed to climb toward the raw sensor reading on each update. Stock is about 1.2 degrees Celsius per update. Effect: Raising it lets the reported coolant temperature rise faster toward the raw sensor reading each update; lowering it slows how quickly it can rise. Evidence: ledger:E0776, ledger:E0805</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x35214" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x279" flags="0x30">
    <title>Exhaust Temperature Model - Base Temperature (Hot Channel)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): each channel&#x27;s target is a base temperature plus an engine speed term and an airflow term, capped at 1000 C. This base is used while the channel is at or above the base switch temperature. Stock 240 C. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = a hotter modelled temperature at every operating point once the channel is hot Evidence: ledger:E0769, ledger:E0852, ledger:E0968, ledger:E1188, ledger:E1192, ledger:E1558</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3525E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1023.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x27A" flags="0x30">
    <title>Exhaust Temperature Model - Base Temperature (Cool Channel)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): each channel&#x27;s target is a base temperature plus an engine speed term and an airflow term. This base is used while the channel is below the base switch temperature. Stock 180 C. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = the modelled temperature climbs faster from cool Evidence: ledger:E0769, ledger:E0852, ledger:E0968, ledger:E1188, ledger:E1192, ledger:E1558</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3526E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1023.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x27B" flags="0x30">
    <title>Exhaust Temperature Model - Base Switch Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): at or above this modelled temperature a channel uses the hot base temperature, below it the cool base temperature. Stock 488 C. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: lower = the hot base applies from a lower modelled temperature Evidence: ledger:E0769, ledger:E0852, ledger:E0968, ledger:E1188, ledger:E1192, ledger:E1558</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3527E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1023.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x27C" flags="0x30">
    <title>Exhaust Temperature Model - Cold Engine Target</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): while the coolant is below the model&#x27;s coolant gate (stock 69 C) each channel moves toward this fixed temperature instead of the speed and airflow target. Stock 300 C. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = a cold engine is modelled with a hotter exhaust Evidence: ledger:E0769, ledger:E0852, ledger:E0968, ledger:E1188, ledger:E1192, ledger:E1558</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3528E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1023.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x27D" flags="0x30">
    <title>Exhaust Temperature Model - Filter Rate, Falling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): fraction of the gap between the model channel&#x27;s target and its present value closed at each model update while the target is below the present value (stock about 1.8 %, 1180 of 65536 = 1.8 % falling, 3277 = 5.0 % rising). Larger = the modelled temperature follows its target faster. Channel 3 is the catalyst channel used by the catalyst monitor readiness count. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = the model follows its target faster Evidence: l...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3529E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x27E" flags="0x30">
    <title>Exhaust Temperature Model - Filter Rate, Rising</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): fraction of the gap between the model channel&#x27;s target and its present value closed at each model update while the target is at or above the present value (stock about 5.0 %, 1180 of 65536 = 1.8 % falling, 3277 = 5.0 % rising). Larger = the modelled temperature follows its target faster. Channel 3 is the catalyst channel used by the catalyst monitor readiness count. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = the model follows its target faster Evide...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x352AE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x27F" flags="0x30">
    <title>Exhaust Temperature Model - Airflow Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): the target rises this much per g/s of airflow (airflow above the airflow input ceiling counts as the ceiling). Stock 2.26 C per g/s, 113 C at the stock 50 g/s ceiling. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = a hotter modelled temperature at higher airflow Evidence: ledger:E0588, ledger:E0769, ledger:E0852, ledger:E1188, ledger:E1192, ledger:E1558</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x352BE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC per g/s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x280" flags="0x30">
    <title>Exhaust Temperature Model - Engine Speed Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): the target rises this much per rpm of engine speed (speed above the engine speed input ceiling counts as the ceiling). Stock 0.205 C per rpm, 820 C at the stock 4000 rpm ceiling. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = a hotter modelled temperature at higher engine speed Evidence: ledger:E0588, ledger:E0769, ledger:E0852, ledger:E1188, ledger:E1192, ledger:E1558</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x352CE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC per rpm</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x281" flags="0x0">
    <title>EVAP Engine-Off Test - Vent Open Abort Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test, first step with the vent open: if the average tank reading is below this the test is abandoned. Stock -0.5 inH2O (0.5 inH2O of pressure). Tank readings are vacuum: positive is vacuum, negative is pressure. Effect: raise (toward 0) = less pressure with the vent open abandons the test Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3574E" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-209715.200000</min>
    <max>209715.199902</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10240"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x282" flags="0x0">
    <title>EVAP Engine-Off Test - Vent Open Derate Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test, first step with the vent open: if the average tank reading is below this (but not below the abort level) the pressure peak is scaled by the derate factor. Stock -0.45 inH2O. Tank readings are vacuum: positive is vacuum, negative is pressure. Effect: raise (toward 0) = the derate applies with less vent-open pressure Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35752" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-209715.200000</min>
    <max>209715.199902</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10240"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x283" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Phase Flat Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the pressure phase ends when the tank reading has stayed inside the flat band for this long. Stock 600 s. Effect: raise = the test waits longer for pressure to build Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3575A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x284" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Phase Early Vacuum Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: vacuum at or above the early vacuum level for this long during the pressure phase starts the vacuum phase at once. Stock 0.1 s. Effect: raise = early vacuum must last longer before the vacuum phase starts Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3575C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x285" flags="0x0">
    <title>EVAP Engine-Off Test - Vacuum Phase Flat Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the vacuum phase ends when the tank reading has stayed inside the flat band for this long. Stock 1000 s. Effect: raise = the test waits longer for vacuum to build Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3575E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x286" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Phase Peak Fall-Back</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the pressure phase ends once the tank reading has come back by this much from its pressure peak. Stock -0.25 inH2O (the value is peak minus current reading, so it is negative). Effect: more negative = a larger fall-back from the peak is needed Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35770" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x287" flags="0x0">
    <title>EVAP Engine-Off Test - Vacuum Phase Peak Fall-Back</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the vacuum phase ends once the tank reading has dropped by this much from its vacuum peak. Stock 0.25 inH2O. Effect: raise = a larger fall-back from the vacuum peak is needed Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35772" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x288" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Phase Early Vacuum Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: a tank reading at or above this during the pressure phase (vacuum instead of pressure) starts the vacuum phase without venting. Stock 0.20 inH2O. Tank readings are vacuum: positive is vacuum, negative is pressure. Effect: raise = more vacuum is needed to skip straight to the vacuum phase Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35774" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x289" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Phase Flat Band Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: lower edge of the band in which the pressure phase counts the tank as not building pressure. Stock -0.31 inH2O. Tank readings are vacuum: positive is vacuum, negative is pressure. Effect: more negative = more pressure still counts as flat Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35776" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x28A" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Phase Flat Band High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: upper edge of the band in which the pressure phase counts the tank as not building pressure. Stock 0.31 inH2O. Tank readings are vacuum: positive is vacuum, negative is pressure. Effect: raise = more vacuum still counts as flat Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35778" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x28B" flags="0x0">
    <title>EVAP Engine-Off Test - Vacuum Phase Flat Band Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: lower edge of the band in which the vacuum phase counts the tank as not building vacuum. Stock -0.30 inH2O. Tank readings are vacuum: positive is vacuum, negative is pressure. Effect: more negative = more pressure still counts as flat Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3577C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x28C" flags="0x0">
    <title>EVAP Engine-Off Test - Vacuum Phase Flat Band High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: upper edge of the band in which the vacuum phase counts the tank as not building vacuum; also the smallest vacuum peak that the peak fall-back check accepts. Stock 0.30 inH2O. Effect: raise = more vacuum still counts as flat Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3577E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x28D" flags="0x0">
    <title>EVAP Engine-Off Test - Vacuum Target Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: smallest vacuum target the vacuum phase may use (the target is otherwise the reference less the pressure already reached). Stock 0 inH2O. Effect: raise = the vacuum phase always needs at least this much vacuum to finish early Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35780" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x28E" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Peak Derate Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: factor applied to the stored pressure peak when the vent-open reading was below the derate level. Stock 0.50. Effect: lower = the pressure peak counts for less after a pressurised vent-open step Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35782" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x28F" flags="0x0">
    <title>EVAP Engine-Off Test - Pressure Phase Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: longest time the pressure phase may last before the test moves on. Stock 2499 s. Effect: raise = the pressure phase may last longer Evidence: ledger:E0776, ledger:E0805, ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3578C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x290" flags="0x0">
    <title>EVAP Engine-Off Test - Refuelling Confirm Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: when the test is disturbed and the fuel level has stayed changed for longer than this, the disturbance is put down to refuelling and not counted against the sensors. Stock 30 s. Effect: raise = the fuel level must stay changed longer to count as refuelling Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35790" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x291" flags="0x0">
    <title>EVAP Engine-Off Test - Disturbance Wait Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: how long a disturbed test waits before the disturbance is counted as a bad sample against the tank pressure sensor (P0454), the fuel level sensor (P0464) or the sensor zero (P0451). Stock 600 s. Effect: raise = a disturbance is counted later Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35792" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x292" flags="0x0">
    <title>EVAP Engine-Off Test - Vent Time Between Phases</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: how long the vent is held open between the pressure phase and the vacuum phase. Stock 45 s. Effect: raise = the tank is vented longer before the vacuum phase Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35794" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x293" flags="0x0">
    <title>EVAP Engine-Off Test - Total Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: once the engine has been off this long the test stops waiting and evaluates what it has. Stock 2500 s. Effect: raise = the test may run longer after shut-off Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35796" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x294" flags="0x0">
    <title>EVAP Engine-Off Test - Re-Vent Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: how long the vent is held open for a re-vent in the vacuum phase. Stock 300 s. Effect: raise = each re-vent lasts longer Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35798" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x295" flags="0x0">
    <title>EVAP Engine-Off Test - Zero Shift Limit, Upward</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): sensor voltage above the stored zero by this much is rated 1.0 and stops the test; smaller shifts are rated in proportion. Used from the second zero check of a test on. Stock 0.20 V. Effect: raise = a larger upward zero shift is tolerated Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3579A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x296" flags="0x0">
    <title>EVAP Engine-Off Test - Zero Shift Limit, Downward</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): the same for a sensor voltage below the stored zero. Used from the second zero check of a test on. Stock 0.20 V. Effect: raise = a larger downward zero shift is tolerated Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3579C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x297" flags="0x0">
    <title>EVAP Engine-Off Test - Zero Shift Limit, Upward (first check)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): upward limit used for the first zero check of a test. Stock 0.20 V. Effect: raise = a larger upward zero shift is tolerated Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3579E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x298" flags="0x0">
    <title>EVAP Engine-Off Test - Zero Shift Limit, Downward (first check)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank pressure sensor zero check of the engine-off EVAP test (P0451): downward limit used for the first zero check of a test. Stock 0.20 V. Effect: raise = a larger downward zero shift is tolerated Evidence: ledger:E1051</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x357A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x299" flags="0x0">
    <title>Ambient Air Temp Estimate - Flush Requirement Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Whenever the airflow or speed gate is not met, the flush requirement grows by one second each second up to this ceiling, and a larger requirement is cut down to it (stock 40 s). The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it down, and until it reaches zero the estimate can only fall toward the intake air temperature. Effect: raise = more flushing is needed again after slowing down Evidence: ledger:E0385, ledger:E1184, l...</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x35D12" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>204.796875</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/320"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x29A" flags="0x0">
    <title>EVAP Engine-Off Test - Tank Pressure Sensor Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: tank pressure sensor slope used by this test, in inH2O of tank vacuum per volt away from the sensor zero. Stock 5.0. Change only for a different sensor. Effect: raise = the same sensor voltage change reads as more pressure Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36000" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>inH2O per V</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x29B" flags="0x0">
    <title>EVAP Engine-Off Test - Unfinished Attempt Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: after this many enabled tests that did not finish, the time since the last test is restarted anyway. Stock 2. Effect: raise = more unfinished attempts are made before the wait starts again Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36002" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x29C" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Trip Distance Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs after a trip of at least this distance. Stock 5 km. Effect: raise = a longer trip is needed before the test runs Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36006" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1048575.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x29D" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Vehicle Distance Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs once the vehicle has covered this distance since new (the counter stops at 6436 km). Stock 16 km. Effect: raise = the test stays off for longer on a new vehicle Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3600A" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1048575.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x29E" flags="0x0">
    <title>EVAP Engine-Off Test - Fuel Level Used on Sensor Fault</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: fuel level assumed while the fuel level sensor is faulted. Stock 50 %. Effect: changes the reference the test uses with a faulted sensor Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3600E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x29F" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Fuel Level Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs with the fuel level at or below this. Stock 85 %. Effect: raise = the test also runs with a fuller tank Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36014" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A0" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Fuel Level Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs with the fuel level at or above this. Stock 15 %. Effect: lower = the test also runs with an emptier tank Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36016" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A1" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Ambient Temperature Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs with ambient air temperature at or below this. Stock 32 degC. Effect: raise = the test also runs on hotter days Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36018" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A2" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Ambient Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs with ambient air temperature at or above this. Stock 2 degC. Effect: lower = the test also runs in colder weather Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3601A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A3" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Coolant Temperature at Shut-Off Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs when coolant temperature at engine shut-off was at or above this. Stock 70 degC. Effect: lower = the test also runs after a cooler shut-off Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3601E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A4" flags="0x0">
    <title>EVAP Engine-Off Test - Fuel Vapour Temperature Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: how fast its filtered fuel vapour temperature follows the sensor, as the fraction of the gap closed per update. Stock 0.10. Effect: lower = the temperature is smoothed more Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36020" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A5" flags="0x0">
    <title>EVAP Engine-Off Test - Tank Pressure Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: how fast the tank reading its phases use follows the sensor, as the fraction of the gap closed per update. Stock 0.0625. Effect: lower = the tank reading is smoothed more (slower to react) Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36022" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A6" flags="0x0">
    <title>EVAP Engine-Off Test - Disturbance Check Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: filter on the tank reading used by the disturbance check, as the fraction of the gap closed per update. Stock 0.05. Effect: lower = the disturbance check sees a smoother tank reading Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36024" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A7" flags="0x0">
    <title>EVAP Engine-Off Test - Disturbance Check Sample Jump Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the disturbance check ignores a pass in which the unfiltered tank reading jumped by this much or more from the previous sample. Stock 1.0 inH2O. Effect: raise = larger sample-to-sample jumps are still judged Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36026" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A8" flags="0x0">
    <title>EVAP Engine-Off Test - Disturbance Pressure Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: a filtered tank reading at or below this with the vent closed flags a disturbance. Stock -4.0 inH2O (4 inH2O of pressure). Tank readings are vacuum: positive is vacuum, negative is pressure. Effect: more negative = more tank pressure is tolerated before a disturbance is flagged Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36028" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2A9" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs after the engine has run at least this long on the trip. Stock 600 s. Effect: raise = a longer run is needed before the test runs Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3602A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2AA" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Time Since Last Test, After a Good Result</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: engine run time plus soak time that must pass since the last test when that test gave a good result. Stock 17 h. Effect: raise = the test runs less often after a good result Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3602C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>h</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2AB" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Time Since Last Test</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: engine run time plus soak time that must pass since the last test in the other cases. Stock 10 h. Effect: raise = the test runs less often Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3602E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>h</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2AC" flags="0x0">
    <title>EVAP Engine-Off Test - Start Delay After Shut-Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test takes over this long after the engine stops. Stock 6 s. Effect: raise = the test starts later after shut-off Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36034" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2AD" flags="0x0">
    <title>EVAP Engine-Off Test - Trip Distance Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the trip distance it requires only counts while vehicle speed is at or above this. Stock 1.6 km/h. Effect: raise = slow driving no longer counts toward the trip distance Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36036" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2AE" flags="0x0">
    <title>EVAP Engine-Off Test - Disturbance Check Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the disturbance check compares the filtered tank reading with a snapshot that is refreshed this often. Stock 1.0 s. Effect: raise = the check looks at pressure changes over a longer interval Evidence: ledger:E0776, ledger:E0805, ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36110" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2AF" flags="0x0">
    <title>EVAP Engine-Off Service Test - Ambient Temperature Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP service test (the scan tool started version of the leak test) only runs with ambient air temperature at or below this while the PCM&#x27;s ambient estimate is not yet valid. Stock 40 degC. Effect: raise = the service test also runs when hotter Evidence: ledger:E1055</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36136" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B0" flags="0x0">
    <title>EVAP Engine-Off Service Test - Ambient Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP service test (the scan tool started version of the leak test) only runs with ambient air temperature at or above this while the PCM&#x27;s ambient estimate is not yet valid. Stock 2 degC. Effect: lower = the service test also runs when colder Evidence: ledger:E1055</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36138" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B1" flags="0x0">
    <title>EVAP Engine-Off Service Test - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP service test (the scan tool started version of the leak test) only runs after the engine has run at least this long (the scan tool shows the time still to go). Stock 1200 s. Effect: raise = a longer run is needed before the service test Evidence: ledger:E1055</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3613A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B2" flags="0x0">
    <title>EVAP Engine-Off Service Test - Trip Distance Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP service test (the scan tool started version of the leak test) only runs after a trip of at least this distance (the scan tool shows the distance still to go). Stock 16.1 km (10 miles). Effect: raise = a longer drive is needed before the service test Evidence: ledger:E1055</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3613E" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1048575.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B3" flags="0x0">
    <title>EVAP Engine-Off Test - Vent Command Mismatch Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the test is ended when the vent valve command has differed from what the test asked for, for this long. Stock 0.5 s. Effect: raise = a longer mismatch is tolerated before the test ends Evidence: ledger:E1055</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36142" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B4" flags="0x0">
    <title>EVAP Engine-Off Test Enable - Barometric Pressure Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test only runs with barometric pressure at or above this. Stock 74 kPa. Effect: raise = the test stops running at lower altitude Evidence: ledger:E1052</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36144" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2B5" flags="0x0">
    <title>EVAP Engine-Off Test - Fuel Level Change Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: a fuel level that differs from the level at the start of the test by more than this disturbs the test (and, if it lasts, counts as refuelling). Stock 20 %. Effect: raise = a larger fuel level change is tolerated during the test Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3614A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x2B6" flags="0x30">
    <title>P0134 / P0140 Check - Fail Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor activity check (P0134 upstream, P0140 downstream): a test window fails once more than this many of its samples are inactive. Stock 950. The array has room for four O2 sensors; this engine has two, so the third and fourth values are never used. Effect: raise = more inactive samples are needed to fail a window Evidence: ledger:E0995, ledger:E1561</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <LABEL index="2" value="sensor 3 (not fitted, unused)" />
      <LABEL index="3" value="sensor 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x366C2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x2B7" flags="0x30">
    <title>P0132 / P0138 Check - Fail Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor high voltage check (P0132 upstream, P0138 downstream): a test window fails once this many of its samples are high. Stock 140 upstream, 950 downstream. Effect: raise = more high samples are needed to fail a window Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x366D2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x2B8" flags="0x30">
    <title>P0132 / P0138 Check - Failed Windows To Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor high voltage check (P0132 upstream, P0138 downstream): the code sets after this many failed test windows in a row. Stock 1. When both sensors fail together, the code is held back for a sensor whose partner sensor has its own failed window flagged, so only the first one reports. Effect: raise = more failed windows in a row are needed to set the code Evidence: ledger:E0994, ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x366EA" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>windows</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x2B9" flags="0x30">
    <title>P0132 / P0138 Check - High Voltage Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor high voltage check (P0132 upstream, P0138 downstream): a sample counts as high when the sensor reads above this. Stock 1000 mV. Effect: lower = lower sensor readings also count as high Evidence: ledger:E0994</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x366A2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x2BA" flags="0x0">
    <title>P0335 Check Enable - RPM Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crank sensor no-signal check (P0335): only runs while engine speed is below this. Stock 2000 rpm. Effect: raise = the check also runs at higher rpm Evidence: ledger:E1026</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2BB" flags="0x0">
    <title>P0335 Fail Time - Starter Engaged</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crank sensor no-signal check (P0335): with the starter engaged and the MAF signal either at or above its threshold or faulted, the code sets after this long without a valid crank signal. Stock 4.0 s. Effect: raise = longer cranking without a crank signal before the code sets Evidence: ledger:E1026</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2BC" flags="0x0">
    <title>P0335 Check Enable - Airflow Minimum, Signal Lost</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crank sensor no-signal check (P0335): outside the starter-engaged case, the check runs only after a crank signal had been established and while mass airflow is at or above this. Stock 3 g/s. Effect: raise = more airflow is needed for the signal-lost case Evidence: ledger:E1026</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2BD" flags="0x0">
    <title>P0335 Fail Time - Signal Lost</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crank sensor no-signal check (P0335): outside the starter-engaged case (crank signal lost while air is still flowing), the code sets after this long without a valid crank signal. Stock 2.0 s. Effect: raise = a longer signal loss is tolerated Evidence: ledger:E1026</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x2BE" flags="0x30">
    <title>Cam Angle Test - Fail Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam angle test (sets P0017 on this engine; runs with the cam phaser parked): bad samples that set the code. Stock 25. The second value belongs to the other cam input, which this test does not check. The array has room for four cam inputs; this engine has two, so the third and fourth values are never used. Effect: raise = more bad samples are needed to set the code Evidence: ledger:E1080, ledger:E1526</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input reporting P0365 / P0366 / P0017" />
      <LABEL index="1" value="cam input reporting P0340 / P0341 / P0016" />
      <LABEL index="2" value="cam input 3 (not fitted, unused)" />
      <LABEL index="3" value="cam input 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36804" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x2BF" flags="0x30">
    <title>Cam Angle Test - Pass Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam angle test (sets P0017 on this engine; runs with the cam phaser parked): samples without reaching the fail count that pass the test. Stock 35. The second value belongs to the other cam input, which this test does not check. The array has room for four cam inputs; this engine has two, so the third and fourth values are never used. Effect: raise = the test needs more samples to pass Evidence: ledger:E1080, ledger:E1526</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input reporting P0365 / P0366 / P0017" />
      <LABEL index="1" value="cam input reporting P0340 / P0341 / P0016" />
      <LABEL index="2" value="cam input 3 (not fitted, unused)" />
      <LABEL index="3" value="cam input 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3680C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x2C0" flags="0x30">
    <title>Cam Signal Lost Test - Fail Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam position sensor signal lost test (P0365 / P0340): time without the pass counts after which the code sets. Stock 3 s. The array has room for four cam inputs; this engine has two, so the third and fourth values are never used. Effect: raise = the cam signal may be missing longer before the code sets Evidence: ledger:E1080, ledger:E1526</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input reporting P0365 / P0366 / P0017" />
      <LABEL index="1" value="cam input reporting P0340 / P0341 / P0016" />
      <LABEL index="2" value="cam input 3 (not fitted, unused)" />
      <LABEL index="3" value="cam input 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x368A4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x2C1" flags="0x0">
    <title>P0446 Fail - Vacuum Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP vent restriction check (P0446): with the vent open and purge flowing, time tank vacuum must stay above the vacuum limit to fail. Stock 5 s. Effect: raise = vacuum must persist longer before P0446 sets Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C2" flags="0x0">
    <title>P0446 Fail - Vacuum Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP vent restriction check (P0446): tank vacuum, with the vent commanded open and purge flowing, above which the vent is judged restricted. Stock 10 inH2O. Effect: raise = more vacuum is tolerated with the vent open Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x368BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C3" flags="0x0">
    <title>EVAP Test - Tank at Atmosphere Window, Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test: lower edge of the tank vacuum window that counts as the tank being at atmosphere (negative = pressure). The purge valve check starts and the vent check proceeds only inside the window; tank pressure beyond this edge during the pull-down voids a gross leak failure. Stock -2.5 inH2O. Effect: lower = more tank pressure still counts as atmosphere Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37190" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C4" flags="0x0">
    <title>EVAP Test - Tank at Atmosphere Window, High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test: upper edge of the tank vacuum window that counts as the tank being at atmosphere. Stock 5 inH2O. Effect: raise = more residual vacuum still counts as atmosphere Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37192" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C5" flags="0x0">
    <title>P0446 Pass - Purge Volume</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP vent restriction check (P0446): purge volume that must flow with the vent open, without tank vacuum building, to pass. Stock 10 L. Effect: raise = more purge must flow before the vent check passes Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37196" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>L</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1024.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4194304"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C6" flags="0x0">
    <title>P0446 Fail - Bleed Down Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP vent restriction check (P0446): longest time for the tank vacuum to return to the atmosphere window after the vent is opened; longer fails. Stock 15 s. Effect: raise = the vent may take longer to bleed the vacuum off Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3719A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C7" flags="0x0">
    <title>EVAP Readiness - Counted Drives to Complete</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of counted drives after which the EVAP monitor is reported complete for readiness (stock 6). The PCM can report the evaporative emission (EVAP) monitor as complete for readiness without the engine-running EVAP test having run: a drive counts when the test&#x27;s cold start conditions are not met and the vehicle has been driven at or above the minimum speed for the required time; after enough counted drives the EVAP monitor reads complete. A drive on which the cold start conditions are met clears the count. Effect: lower = the EVAP monitor reads complete after fewer drives Evidence: ledger:E0775, ledger:E1072, ledger:E1356</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371A2" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>drives</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C8" flags="0x0">
    <title>EVAP Test - Barometric Pressure Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: lowest barometric pressure at which the test runs. Stock 74 kPa. Effect: lower = the test also runs at higher altitude Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2C9" flags="0x0">
    <title>EVAP Readiness - Counted Drive Minimum Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Driving time toward a counted drive only accumulates at or above this vehicle speed (stock 24 km/h). The PCM can report the evaporative emission (EVAP) monitor as complete for readiness without the engine-running EVAP test having run: a drive counts when the test&#x27;s cold start conditions are not met and the vehicle has been driven at or above the minimum speed for the required time; after enough counted drives the EVAP monitor reads complete. A drive on which the cold start conditions are met clears the count. Effect: raise = a counted drive needs a higher speed Evidence: ledger:E0775, ledger:E1072, ledger:E1356</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2CA" flags="0x0">
    <title>EVAP Readiness - Counted Drive Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Driving time at or above the minimum speed needed for a drive to count (stock 30 s). The PCM can report the evaporative emission (EVAP) monitor as complete for readiness without the engine-running EVAP test having run: a drive counts when the test&#x27;s cold start conditions are not met and the vehicle has been driven at or above the minimum speed for the required time; after enough counted drives the EVAP monitor reads complete. A drive on which the cold start conditions are met clears the count. Effect: raise = a counted drive needs more driving time Evidence: ledger:E0775, ledger:E1072, ledger:E1356</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371AA" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2CB" flags="0x0">
    <title>EVAP Test - Voltage Out of Range Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: time system voltage may be outside its window before the test is switched off for the trip. Stock 12 s. Effect: raise = a longer voltage excursion is tolerated Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2CC" flags="0x0">
    <title>EVAP Test - Fuel Level Out of Range Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: time fuel level may be outside its window before the test is switched off for the trip. Stock 15 s. Effect: raise = a longer fuel level excursion is tolerated Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371B2" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2CD" flags="0x0">
    <title>EVAP Test - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: lowest system voltage. Stock 11 V. Effect: lower = the test also runs at lower voltage Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2CE" flags="0x0">
    <title>EVAP Test - System Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: highest system voltage. Stock 18 V. Effect: raise = the test also runs at higher voltage Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2CF" flags="0x0">
    <title>EVAP Test - Fuel Level Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: lowest fuel level. Stock 15 %. Effect: lower = the test also runs with less fuel Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D0" flags="0x0">
    <title>EVAP Test - Intake Air Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: highest intake air temperature. Stock 30 C. Effect: raise = the test also runs in warmer air Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D1" flags="0x0">
    <title>EVAP Test - Startup Coolant Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: highest coolant temperature at engine start (the test needs a cold start). Stock 30 C. Effect: raise = the test also runs after a warmer start Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371D4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D2" flags="0x0">
    <title>Fuel Tank Pressure Sensor - Zero Learn Intake Air Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel tank pressure sensor: the zero (tank at atmosphere) is learned at a cold key-on only while intake air temperature is below this and above 4 C. Stock 30 C. Effect: raise = the zero is also learned on warmer starts Evidence: ledger:E1072, ledger:E1073, ledger:E1189</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371DC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D3" flags="0x0">
    <title>EVAP Test - Intake Air Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: lowest intake air temperature. Stock 4 C. Effect: lower = the test also runs in colder air Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371DE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D4" flags="0x0">
    <title>EVAP Test - Fuel Level Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test (P0455 / P0446 / P0496) run condition: highest fuel level. Stock 85 %. Effect: raise = the test also runs with a fuller tank Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371E0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D5" flags="0x0">
    <title>Monitor Enable, Minimum Engine Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The EVAP fuel level change check and the fuel tank pressure change check run only after the engine has run this long since start. Stock 10 seconds. Effect: raise = the change checks start later after start-up Evidence: ledger:E0217, ledger:E0775, ledger:E0811, ledger:E1556</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37334" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D6" flags="0x0">
    <title>EVAP Test - Abort Tank Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test: with the vent commanded closed, tank vacuum below this (negative = pressure in the tank) aborts the test for the trip. Stock -2.5 inH2O. Effect: lower = more tank pressure is tolerated before the test is aborted Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37350" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D7" flags="0x0">
    <title>EVAP Test - Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test: engine run time after which an unfinished test is ended for the trip. Stock 1000 s. Effect: raise = the test may finish later in the trip Evidence: ledger:E1072</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3735A" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D8" flags="0x0">
    <title>P0496 Test - Atmosphere Wait</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve leak check (P0496): longest wait for the tank to reach the atmosphere window before the check; after it the check is skipped. Stock 15 s. Effect: raise = the check waits longer for the tank to settle Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37362" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2D9" flags="0x0">
    <title>P0496 Fail - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve leak check (P0496): with purge commanded off and the vent closed, time tank vacuum must stay above the limit to fail. Stock 5 s. Effect: raise = vacuum must persist longer before P0496 sets Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37364" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2DA" flags="0x0">
    <title>P0496 Fail - Vacuum Limit, Cold Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve leak check (P0496): tank vacuum, with purge commanded off and the vent closed, above which the purge valve is judged leaking; used when startup coolant is below the cold start temperature. Stock 10 inH2O. Effect: raise = more vacuum is tolerated with purge off Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37368" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2DB" flags="0x0">
    <title>P0496 Fail - Vacuum Limit, Warm Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve leak check (P0496): same limit when startup coolant is at or above the cold start temperature. Stock 10 inH2O. Effect: raise = more vacuum is tolerated with purge off Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3736A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2DC" flags="0x0">
    <title>P0496 Pass - Time, Warm Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve leak check (P0496): time with purge off without the vacuum limit being exceeded that passes the check, warm start. Stock 60 s. Effect: raise = the check runs longer before it passes Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3736E" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2DD" flags="0x0">
    <title>P0496 Test - Cold Start Coolant Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve leak check (P0496): startup coolant temperature below which the cold start limit and pass time are used. Stock 30 C. Effect: raise = more starts use the cold start values Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37378" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2DE" flags="0x0">
    <title>P0455 Test - Tank Pressure Void Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak test (P0455): time the tank may show pressure beyond the low edge of the atmosphere window during the pull-down before a gross leak failure of this test is disregarded. Stock 5 s. Effect: raise = pressure must persist longer before a failure is disregarded Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37976" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2DF" flags="0x0">
    <title>P0455 Pass - Vacuum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak test (P0455): tank vacuum that passes the test when reached during the pull-down. Stock 8 inH2O. Effect: lower = less vacuum is enough to pass the gross leak test Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37978" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E0" flags="0x0">
    <title>P0455 Fail - Purge Volume</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak test (P0455): purge volume drawn from the sealed system without reaching the pass vacuum that fails the test. Stock 15 L. Effect: raise = more purge may be drawn before the gross leak test fails Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3797A" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>L</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1024.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4194304"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E1" flags="0x0">
    <title>Fuel Tank Pressure Sensor - Zero Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel tank pressure sensor: lowest sensor voltage accepted as the zero (tank at atmosphere) when the zero is learned at a cold key-on. Stock 1.20 V. Effect: lower = a lower sensor voltage is accepted as the zero Evidence: ledger:E1073</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37998" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E2" flags="0x0">
    <title>Fuel Tank Pressure Sensor - Zero Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel tank pressure sensor: highest sensor voltage accepted as the zero when the zero is learned at a cold key-on. Stock 1.80 V. Effect: raise = a higher sensor voltage is accepted as the zero Evidence: ledger:E1073</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3799A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E3" flags="0x0">
    <title>Fuel Tank Pressure Sensor - Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel tank pressure sensor: tank vacuum per volt of sensor signal away from the learned zero, used by the engine-running EVAP test. Stock 5.0 inH2O per V. Change only for a different sensor. Effect: raise = the same sensor voltage reads as more vacuum Evidence: ledger:E1073</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3799C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>inH2O per V</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E4" flags="0x0">
    <title>EVAP Re-Check - Pass Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak re-check (runs on a later trip after a gross leak failure, P0455): time tank vacuum must stay at or above the pass vacuum. Stock 5 s. Effect: raise = vacuum must hold longer to pass Evidence: ledger:E1073</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37A56" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x2E5" flags="0x30">
    <title>P0449 Circuit Check - Fault Count and Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP vent valve circuit check P0449: the code sets once the first value&#x27;s number of faulted samples is reached; if the second value&#x27;s number of samples is reached first, the check passes and both counts start again. Stock 100 and 120. Effect: raise the first value = more faulted samples are needed to set the code; raise the second = each window is longer Evidence: ledger:E1058</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>value</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="fault samples to fail" />
      <LABEL index="1" value="window samples to pass" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37AE6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x2E6" flags="0x0">
    <title>Fuel Trim Monitor - Purge Off Test Wait Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): longest wait for a result of the purge-off test after a rich reading asked for it; then the request is dropped. Stock 600 s. Effect: raise = the monitor waits longer for the purge-off test Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D74" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E7" flags="0x0">
    <title>Fuel Trim Monitor - Rich Segments to Fail</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): number of purge-off segments that read rich needed to set P0172. Stock 2. Effect: raise = more rich segments are needed before P0172 sets Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D76" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>segments</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E8" flags="0x0">
    <title>Fuel Trim Monitor - Not Rich Segments to Pass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): number of purge-off segments that do not read rich needed to pass P0172. Stock 2. Effect: raise = more clean segments are needed to pass Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D78" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>segments</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2E9" flags="0x0">
    <title>Fuel Trim Monitor - Segments per Test</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): most purge-off segments in one test; when they are used up without a verdict the test ends undecided. Stock 3. Effect: raise = a test may run more purge-off segments Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D7A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>segments</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2EA" flags="0x0">
    <title>Fuel Trim Monitor - Unbroken Filtering Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): unbroken filtering time needed before each lean or rich evaluation. Stock 2 s. Effect: raise = evaluations come less often Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D7E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2EB" flags="0x0">
    <title>Fuel Trim Monitor - Purge Off Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): time purge must have been at the test level, with the fuel trim settled, before the purge-off measurement starts. Stock 1 s. Effect: raise = the measurement starts later after purge is shut off Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DCA" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2EC" flags="0x0">
    <title>Fuel Trim Monitor - Purge Restore Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): time after the measurement ends, with the fuel trim settled, before the trim hold is released and normal sampling resumes. Stock 1 s. Effect: raise = normal trim sampling resumes later after a test Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DCE" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2ED" flags="0x0">
    <title>Fuel Trim Monitor - Test Start Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): longest wait for the purge control and the fuel trim to accept the test request; after it the attempt is abandoned. Stock 2 s. Effect: raise = the test waits longer to start Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DDA" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2EE" flags="0x0">
    <title>Fuel Trim Monitor - Wait After a Test</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): wait before the next test after one in which at least one purge-off segment was evaluated. Stock 300 s. Effect: raise = purge-off tests repeat less often Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DDE" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2EF" flags="0x0">
    <title>Fuel Trim Monitor - Ramp Down Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): longest time to bring purge down to the test level in a non-purge fuel trim cell; after it the attempt is abandoned. Stock 10 s. Effect: raise = the ramp down may take longer Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DF6" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F0" flags="0x0">
    <title>Fuel Level Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the fuel level the PCM reports (fuel level PID) and uses follows the level looked up from the sender: the fraction of the gap closed per update. Stock 0.80. Effect: lower = the reported fuel level is smoothed more (slower to change) Evidence: ledger:E0956</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x37F20" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x2F1" flags="0x30">
    <title>P0201 to P0205 Circuit Check - Fault Count and Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Injector circuit checks P0201 to P0205 (one count pair per cylinder): the code sets once the first value&#x27;s number of faulted samples is reached; if the second value&#x27;s number of samples is reached first, the check passes and both counts start again. Stock 10 and 20. Effect: raise the first value = more faulted samples are needed to set the code; raise the second = each window is longer Evidence: ledger:E1058</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>value</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="fault samples to fail" />
      <LABEL index="1" value="window samples to pass" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3866C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x2F2" flags="0x0">
    <title>Injector Circuit Test - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The injector circuit fault checks (P0201 to P0205) only run after system voltage has stayed above this for the Injector Circuit Test - Voltage OK Time. At or below it the timer restarts and the checks stop. Stock 11.0 V. Effect: raise = the injector circuit checks need a higher system voltage before they run Evidence: ledger:E0772, ledger:E1372</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38672" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F3" flags="0x0">
    <title>Misfire - Catalyst Test History Depth</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: how many of the most recent 200-revolution windows (16 are stored) are searched for windows that failed the catalyst-damage limit. Stock 16. Effect: lower = only the newest windows count toward a catalyst-damage misfire decision Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A36" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>windows</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F4" flags="0x0">
    <title>Misfire - Emission Test History Depth</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: how many of the most recent 200-revolution windows (16 are stored) are searched for windows that failed the emission limit. Stock 16. Effect: lower = only the newest windows count toward an emission misfire decision Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A38" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>windows</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F5" flags="0x0">
    <title>Misfire - Idle Exception Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: an event shaped like a disturbance (not a clean misfire) is normally set aside as abnormal. Below this engine speed, with vehicle speed and throttle below their idle exception limits, it is counted as a misfire anyway. Stock 1000 rpm. Effect: raise = the idle exception reaches higher engine speed Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A44" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F6" flags="0x0">
    <title>Misfire - Idle Exception Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: commanded throttle below which the idle exception of the abnormal event test applies. Stock 3.0 %. Effect: raise = the idle exception reaches more throttle Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A46" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F7" flags="0x0">
    <title>Misfire - Idle Exception Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: vehicle speed below which the idle exception of the abnormal event test applies. Stock 5 km/h. Effect: raise = the idle exception reaches higher vehicle speed Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A48" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F8" flags="0x0">
    <title>Misfire - Quiet Cycles That End a Run</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: number of engine cycles in a row without a misfire that ends a run of misfiring cycles. Stock 3. Effect: raise = a run of misfiring cycles lasts across longer quiet gaps Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A4A" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2F9" flags="0x0">
    <title>Misfire - Run Counting Start Cycle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: in a run of engine cycles that each show a misfire, the first cycle is counted and then every cycle from this one on; the cycles in between are not counted. Stock 7. Effect: lower = more cycles of a continuous misfire are counted Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A4B" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2FA" flags="0x0">
    <title>Misfire - Low Load Pause</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: pause, in engine cycles, requested while load is below the minimum load curve. Stock 4. Effect: raise = the monitor stays paused longer after load rises above the minimum Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A8E" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2FB" flags="0x0">
    <title>Misfire - Overspeed Pause</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: pause, in engine cycles, requested at or above the overspeed pause engine speed. Stock 0 (none). Effect: raise = the monitor pauses above the overspeed engine speed Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38AA0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2FC" flags="0x0">
    <title>Misfire - Low Fuel Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: fuel level below which the monitor is paused (misfire from running out of fuel is not reported), unless P0300 is already confirmed. Stock 2.5 %. Effect: raise = the monitor pauses at a higher fuel level Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38AA2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2FD" flags="0x0">
    <title>Misfire - Low Fuel Pause</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: pause, in engine cycles, requested while fuel level is below the low fuel level. Stock 88. Effect: raise = the monitor stays paused longer after a low fuel reading Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38AA4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2FE" flags="0x0">
    <title>Misfire - Low Fuel Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: engine run time before the low fuel pause can be requested. Stock 5 s. Effect: raise = low fuel is ignored for longer after each start Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38AA8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x2FF" flags="0x0">
    <title>Misfire - General Pause</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: pause, in engine cycles, requested while the run conditions are not met, on a crank sync error and during fuel cut. Stock 4. Effect: raise = the monitor stays paused longer after these conditions end Evidence: ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38AAC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cycles</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x300" flags="0x0">
    <title>Misfire - Dead Cylinder Misfire Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: misfires of one cylinder in a 200-revolution window (100 firings of that cylinder) at or above which it is treated as a dead cylinder for the catalyst-damage exemption. Stock 90. Effect: lower = a cylinder is treated as dead at fewer misfires Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396A2" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>misfires</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>127.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x301" flags="0x0">
    <title>Misfire Monitor - Cold Start Release Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: after a start below the cold start limit, the monitor is released once coolant reaches this. Stock 21 degC. Effect: raise = after a cold start the monitor waits for a warmer engine Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x302" flags="0x0">
    <title>Misfire Monitor - Cold Start Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: if coolant is at or above this when the monitor is reset at start-up, the monitor is released straight away; otherwise it waits for the cold start release temperature. Stock -7 degC. Effect: raise = more starts count as cold starts Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x303" flags="0x0">
    <title>Misfire Monitor - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: system voltage must be at or above this (not checked during the voltage grace time after start). Stock 9 V. Effect: raise = the monitor stops at a higher system voltage Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x304" flags="0x0">
    <title>Misfire Monitor - System Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: system voltage must be at or below this (not checked during the voltage grace time after start). Stock 18 V. Effect: lower = the monitor stops at a lower system voltage Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x305" flags="0x0">
    <title>Misfire Monitor - Run Time Before Voltage and Pause Checks</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: the system voltage limits are not applied until the engine has run this long. The same run time must pass before the low load pause, the fuel cut pause and the crank sync pause can be requested. Stock 5 s. Effect: raise = voltage, low load and fuel cut are ignored for longer after each start Evidence: ledger:E1038, ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x306" flags="0x0">
    <title>Misfire Monitor - Coolant Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: coolant temperature must be at or above this. Stock -7 degC. Effect: raise = the monitor needs a warmer engine Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x307" flags="0x0">
    <title>Misfire Monitor - Coolant Temperature Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: coolant temperature must be at or below this. Stock 125 degC. Effect: lower = the monitor stops at a lower coolant temperature Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x308" flags="0x0">
    <title>Misfire Monitor - RPM Needing Crank Variation Learned</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: above this engine speed the monitor only runs once the crankshaft variation check (P0315) has reported a pass. Stock 1000 rpm. Effect: raise = the monitor runs to a higher rpm without the crankshaft variation learned Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x309" flags="0x0">
    <title>Misfire Monitor - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: engine speed must be at or above this. Stock 450 rpm. Effect: raise = the monitor starts at a higher engine speed Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x30A" flags="0x0">
    <title>Misfire Monitor - RPM Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor run condition: engine speed must be at or below this. Stock 6200 rpm. Effect: lower = the monitor stops at a lower engine speed Evidence: ledger:E1038</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x30B" flags="0x0">
    <title>Misfire - Single Cylinder Share for P030x</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: when one cylinder holds more than this share of the stored misfire history, the code is reported with that cylinder number (P0301 to P0305) instead of P0300. Stock 90 %. Effect: lower = a cylinder-specific code is reported more readily Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x30C" flags="0x0">
    <title>Misfire - MIL Flash Fuel Cut Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: the flashing check engine lamp request for catalyst-damaging misfire is dropped once deceleration fuel cut has lasted this long. Stock 3 s. Effect: raise = the lamp keeps flashing longer into a fuel cut Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x30D" flags="0x0">
    <title>Misfire - MIL Flash Low Load Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: once P0300 is confirmed, the lamp does not flash while load is at or below this and vehicle speed is at or below the low speed limit. Stock 30 %. Effect: raise = the lamp stays steady up to a higher load Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x30E" flags="0x0">
    <title>Misfire - MIL Flash Trip Window Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: number of catalyst-damaging windows in this trip above which the lamp keeps flashing after the misfire itself has stopped. Stock 65535 (never). Effect: lower = the lamp keeps flashing for the rest of the trip after fewer windows Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>windows</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x30F" flags="0x0">
    <title>Misfire - MIL Flash Low Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: once P0300 is confirmed, the lamp does not flash while vehicle speed is at or below this and load is at or below the low load limit. Stock 30 km/h. Effect: raise = the lamp stays steady up to a higher speed Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x310" flags="0x0">
    <title>P0136 Test - Run Condition, Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0136 (downstream O2 sensor swing test): engine run time from which the test routines run. Stock 2 s. Effect: raise = the downstream sensor swing test starts later after each start Evidence: ledger:E1079</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x398D8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x311" flags="0x0">
    <title>P0030 / P0036 Check Enable - Ignition Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater circuit check (P0030 upstream, P0036 downstream): only runs with ignition voltage below this. Stock 18.0 V. Effect: lower = the check stops at a lower voltage Evidence: ledger:E1006</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CF7C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x312" flags="0x0">
    <title>P0030 / P0036 Check Enable - Ignition Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater circuit check (P0030 upstream, P0036 downstream): only runs with ignition voltage above this. Stock 11.0 V. Effect: raise = the check needs a higher voltage to run Evidence: ledger:E1006</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CF7E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x313" flags="0x0">
    <title>P0030 / P0036 Check Enable - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 heater circuit check (P0030 upstream, P0036 downstream): only runs with engine speed at or above this. Stock 425 rpm. Effect: raise = the check needs a higher rpm to run Evidence: ledger:E1006</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2CF82" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x314" flags="0x30">
    <title>P0351 to P0355 Circuit Check - Fault Count and Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Ignition coil circuit checks P0351 to P0355 (one count pair per cylinder): the code sets once the first value&#x27;s number of faulted samples is reached; if the second value&#x27;s number of samples is reached first, the check passes and both counts start again. Stock 20 and 100. Effect: raise the first value = more faulted samples are needed to set the code; raise the second = each window is longer Evidence: ledger:E1058</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>value</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="fault samples to fail" />
      <LABEL index="1" value="window samples to pass" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39A7C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x315" flags="0x30">
    <title>Throttle Area-to-Throttle Curve - Area Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle area points (percent of full area) at which the throttle area to throttle position curve is defined. The commanded and idle throttle area are looked up against these points. Stock 0.07 to 100 %, closely spaced at small openings. Effect: moves the axis of the throttle area to throttle position curve: keep 33 points and keep them rising Evidence: ledger:E0232, ledger:E0424, ledger:E0443, ledger:E0785, ledger:E1184</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23F92" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle area</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x316" flags="0x30">
    <title>ETC Throttle Limit - Torque Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stored torque breakpoints (33 points) that index the rows of the ETC throttle limit table. Editing them moves where each row of that table applies. Effect: moves the axis of every table that uses it: edit with care Evidence: ledger:E0443</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x315AC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x317" flags="0x30">
    <title>Misfire - RPM Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stored rpm breakpoints (26 points, 400 to 7000 rpm) that index the columns of the misfire table. Effect: moves the axis of every table that uses it: edit with care Evidence: ledger:E0443</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>26</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38AB0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x318" flags="0x30">
    <title>Fuel - Coolant Breakpoints, shared (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Stored coolant breakpoints (17 points) shared by several fuel tables: editing them moves the coolant axis of all of those tables at once. Effect: moves the axis of every table that uses it: edit with care Evidence: ledger:E0443</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26E1C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x319" flags="0x30">
    <title>Ambient Air Temp Estimate - Engine-Off Soak Time Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off soak time of each point of the flush requirement curve (0 to 25200 s = 7 h). The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it down, and until it reaches zero the estimate can only fall toward the intake air temperature. Axis data: keep ascending. Effect: moves the flush requirement points along soak time Evidence: ledger:E0385, ledger:E1184, ledger:E1334</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35FB0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x31A" flags="0x30">
    <title>Idle Air Valve Map - Idle Area Breakpoints (unused, dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle area command breakpoints of the idle air valve position map used by valve-type idle systems. Axis data: keep ascending. The idle air valve driver is not built into this OS and the idle speed controller always uses the electronic throttle path, so this has no effect on this truck (dormant). Effect: no effect on this truck Evidence: ledger:E0443, ledger:E1279</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A0AE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% of throttle area</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>182.041667</max>
      <MATH equation="X/360"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x31B" flags="0x30">
    <title>Idle Air Valve Map - Valve Position vs Idle Area (unused, DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air valve position for each idle area breakpoint, used by valve-type idle systems. Shown as the raw stored value. The idle air valve driver is not built into this OS and the idle speed controller always uses the electronic throttle path, so this has no effect on this truck (dormant). Reference only: DO NOT EDIT. Effect: no effect on this truck Evidence: ledger:E0443, ledger:E0899, ledger:E1279</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A0F6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>-32768.000000</min>
      <max>32767.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x31C" flags="0x30">
    <title>P0125 - Required Air Mass vs Start-Up Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up check P0125: air mass the engine must have drawn since start, by coolant temperature at start-up, before the check judges whether coolant has reached the target. Stock 8129 g at -40 C falling to 1241 g from 44 C. Effect: raise = the engine gets more time (air) to warm up before P0125 can set Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>degC (start-up coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3519E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x31D" flags="0x30">
    <title>P0128 - Required Air Mass vs Start-Up Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Thermostat check P0128: air mass the engine must have drawn since start, by coolant temperature at start-up, before the check judges whether coolant has reached the target. Stock 11973 g at -40 C falling to 3429 g at 80 C. Effect: raise = the engine gets more time (air) to warm up before P0128 can set Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>degC (start-up coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x351B6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x31E" flags="0x30">
    <title>P0128 - Required Air Mass vs Start-Up Coolant (third column, unused)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Third column of the P0125 / P0128 required air mass curves; the stock instance count (2) leaves it unused. Dormant: no effect on this truck&#x27;s software. Effect: none with the stock instance count Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>degC (start-up coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x351CE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x31F" flags="0x30">
    <title>Throttle Follower Airflow Ceiling vs RPM</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest follower airflow, by engine speed. Rows: In Gear, Park/Neutral. Stock 32 g/s (no limit). Part of the idle throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. Effect: lower = less follower air allowed at that engine speed Evidence: ledger:E0292, ledger:E0445, ledger:E1187</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="In Gear" />
      <LABEL index="1" value="Park/Neutral" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B3DC" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x320" flags="0x30">
    <title>Generator Control - Low Engine Speed Limit vs Desired Idle, In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In gear. While the engine runs at or below this speed, looked up from the desired idle speed, the generator (alternator) control leaves its normal output command and uses its low speed command, until engine speed rises above it or the low speed time limit runs out. Stock 450 rpm at 500 rpm desired idle, 525 rpm from 600 rpm desired idle up. Effect: raise = the generator control switches to its low speed command at a higher engine speed Evidence: ledger:E0445, ledger:E1367</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="500" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="700" />
      <LABEL index="3" value="800" />
      <LABEL index="4" value="900" />
      <LABEL index="5" value="1000" />
      <LABEL index="6" value="1100" />
      <LABEL index="7" value="1200" />
      <LABEL index="8" value="1300" />
      <LABEL index="9" value="1400" />
      <LABEL index="10" value="1500" />
      <LABEL index="11" value="1600" />
      <LABEL index="12" value="1700" />
      <LABEL index="13" value="1800" />
      <LABEL index="14" value="1900" />
      <LABEL index="15" value="2000" />
      <LABEL index="16" value="2100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29974" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x321" flags="0x30">
    <title>LTFT Follow Rate per Cell (Fuel Trim Monitor Hold)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per long term fuel trim cell: how fast the applied long term trim moves to its target while the fuel trim monitor holds the trim for its purge-off test, as the fraction of the gap closed per update. In normal operation the follow rate comes from the LTFT follow rate curve by MAP change instead. Stock 0.01 in cells 0 to 20 and 0.99 in cells 21 to 38. Effect: raise = the applied trim reaches its target faster during the monitor&#x27;s hold Evidence: ledger:E0445, ledger:E0954, ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>39</indexcount>
      <units>LTFT cell index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <LABEL index="33" value="33" />
      <LABEL index="34" value="34" />
      <LABEL index="35" value="35" />
      <LABEL index="36" value="36" />
      <LABEL index="37" value="37" />
      <LABEL index="38" value="38" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24A80" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="39" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x322" flags="0x0">
    <title>Idle Speed Control - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: time the idle speed must stay settled before the settle idle offset is removed. Stock 3.75 s. Effect: raise = the settle offset stays longer Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x223EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x323" flags="0x0">
    <title>Idle Speed Control - Throttle Open Idle Offset Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: time the throttle open idle offset stays on after the throttle closes. Stock 3.75 s. Effect: raise = the offset stays longer after the throttle closes Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x223EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x324" flags="0x0">
    <title>Idle Speed Control - Settle Error Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: the average rpm error may be above the settle maximum for this long before the settle timer restarts. Stock 1.25 s. Effect: raise = longer excursions are tolerated Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x223F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x325" flags="0x30">
    <title>Idle Acquire - RPM Reference Ramp Step vs Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While idle control acquires, the idle rpm reference moves toward desired idle by this many rpm per update, by the reference minus target (negative = reference below target). Stock 0.25 to 3 rpm below, up to 22 rpm above. Effect: raise = reference reaches desired idle faster on the way down / up Evidence: ledger:E0449</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-256" />
      <LABEL index="1" value="-192" />
      <LABEL index="2" value="-128" />
      <LABEL index="3" value="-64" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="64" />
      <LABEL index="6" value="128" />
      <LABEL index="7" value="192" />
      <LABEL index="8" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2240C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm per update</units>
      <decimalpl>0</decimalpl>
      <min>-4096.000000</min>
      <max>4095.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x326" flags="0x0">
    <title>Idle Acquire - RPM Reference Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest idle rpm reference and target used while idle control acquires. Stock 625 rpm. Effect: raise = idle acquire never aims below this rpm Evidence: ledger:E0449</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x223E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x327" flags="0x0">
    <title>Idle Speed Control Acquire - Idle Target Minimum With MAP Sensor Fault</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: lowest idle speed target while the controller is catching the idle speed and a MAP sensor code (P0106 / P0107 / P0108) is failing. Stock 750 rpm (625 rpm without the fault). Effect: raise = higher minimum idle with a failed MAP sensor Evidence: ledger:E1108</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x223EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x328" flags="0x30">
    <title>Oil Life - Revolution Weight vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Each engine revolution counts this many times toward oil wear, by corrected coolant temperature. Stock 7 at -40 C, 1 at 72 to 120 C, rising to 64 at the hottest points. Effect: raise = oil life drops faster at that temperature Evidence: ledger:E0450, ledger:E1185</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-24" />
      <LABEL index="2" value="-8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="24" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="56" />
      <LABEL index="7" value="72" />
      <LABEL index="8" value="88" />
      <LABEL index="9" value="104" />
      <LABEL index="10" value="120" />
      <LABEL index="11" value="136" />
      <LABEL index="12" value="152" />
      <LABEL index="13" value="168" />
      <LABEL index="14" value="184" />
      <LABEL index="15" value="200" />
      <LABEL index="16" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x228FA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x329" flags="0x0">
    <title>Oil Life - Weighted Revolutions per 0.1 %</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weighted engine revolutions that use up 0.1 % of oil life. Stock 40000. Effect: changes when the oil change reminder comes on Evidence: ledger:E0450, ledger:E1185</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x228EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>revs</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x32A" flags="0x0">
    <title>Oil Life - Steps in a Full Oil Life</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Oil life monitor: number of steps written at an oil life reset; oil life is reported as the steps left divided by this. Stock 1000 (each step is 0.1 %). Effect: raise = more steps (longer oil life) before it reads zero Evidence: ledger:E1060</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x228F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>steps</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x32B" flags="0x0">
    <title>Oil Life - Maximum Distance</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Oil life monitor: distance after an oil life reset at which oil life reads zero whatever the engine has done. Stock 16093 km (10,000 miles). Effect: lower = oil life runs out after a shorter distance Evidence: ledger:E1060</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x228F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x32C" flags="0x0">
    <title>Oil Life - Overheat Zeroing Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant at or above this for the delay below forces oil life to zero, when enabled. Stock 135 C (disabled on the H3). (E0450) Effect: changes when the oil change reminder comes on Evidence: ledger:E0450</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x228F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x32D" flags="0x0">
    <title>Oil Life - Overheat Zeroing Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Oil life monitor: how long coolant must stay at or above the overheat zeroing temperature before oil life is forced to zero (only when overheat zeroing is enabled; it is off in the stock calibration). Stock 3 s. Effect: raise = a longer overheat is needed before oil life is zeroed Evidence: ledger:E1060</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x228F6" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x32E" flags="0x0">
    <title>Oil Life - Overheat Zeroing Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1 = a severe overheat zeroes oil life. Stock 0 (off). (E0450) Effect: changes when the oil change reminder comes on Evidence: ledger:E0450</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x228E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x32F" flags="0x30">
    <title>Idle Acquire - Expected MAF vs RPM (In Gear)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow the engine should need at idle in gear, by the idle rpm reference. Idle control finishes acquiring (hands over to closed-loop rpm control) once the measured MAF settles within 0.5 g/s of this. Stock 3.42 / 4.24 / 5.13 / 6.29 / 7.77 g/s at 550 to 950 rpm. Effect: raise = idle acquire expects more airflow before it hands over Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="550" />
      <LABEL index="1" value="650" />
      <LABEL index="2" value="750" />
      <LABEL index="3" value="850" />
      <LABEL index="4" value="950" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x224C0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x330" flags="0x30">
    <title>Idle Acquire - Expected MAF vs RPM (Park/Neutral)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow the engine should need at idle in Park / Neutral, by the idle rpm reference. Idle control finishes acquiring (hands over to closed-loop rpm control) once the measured MAF settles within 0.5 g/s of this. Stock 3.13 / 3.74 / 4.39 / 4.98 / 5.78 g/s at 550 to 950 rpm. Effect: raise = idle acquire expects more airflow before it hands over Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="550" />
      <LABEL index="1" value="650" />
      <LABEL index="2" value="750" />
      <LABEL index="3" value="850" />
      <LABEL index="4" value="950" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x224CC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x331" flags="0x0">
    <title>Idle Acquire - Expected MAF A/C Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the expected idle airflow while the A/C clutch is engaged. Stock 2.10 g/s. Effect: raise = more airflow expected with A/C on Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x224B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x332" flags="0x0">
    <title>Idle Acquire - Expected MAF Adder, Alternate (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on this operating system: added to the expected idle airflow only while an internal flag is set, and that flag is never set (E0824, E0842). Stock 1.60 g/s. Effect: no effect at stock (the adder is never applied on this operating system) Evidence: ledger:E0453, ledger:E0824, ledger:E0842</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x224B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x333" flags="0x0">
    <title>Idle Acquire - MAF Samples Averaged</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAF readings averaged (one per 25 ms) for each expected-airflow comparison. Stock 20 (0.5 s). Effect: raise = slower, steadier comparison Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x224AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>-32768.000000</min>
    <max>32767.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x334" flags="0x0">
    <title>Idle Acquire - Expected MAF Learn Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Step by which the expected-airflow correction moves toward the measurement after each comparison. Stock 0.25 g/s. Effect: raise = correction learns faster Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x224B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x335" flags="0x0">
    <title>Idle Acquire - MAF Tolerance to Finish</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Acquire finishes only when two successive mean-MAF readings are within this of the expected airflow. Stock 0.50 g/s. Effect: raise = acquire finishes sooner Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x224B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x336" flags="0x0">
    <title>Idle Acquire - Max Target RPM to Finish</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Acquire finishes only when the idle rpm target is at or below this. Stock 1500 rpm. Effect: lower = no hand-over at high idle targets Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x224B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x337" flags="0x0">
    <title>Idle Acquire - Min Coolant to Finish</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Acquire finishes only when coolant is at or above this. Stock 60 C. Effect: lower = hand-over allowed on a colder engine Evidence: ledger:E0453</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x224BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x338" flags="0x0">
    <title>Idle Acquire - Completion Engine Speed Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed acquire (the step that brings engine speed down to the desired idle after coming off throttle) only completes and hands over to idle speed control while the engine speed is within this much of the acquire reference speed (absolute error), together with its other conditions. Stock 50 rpm. Effect: raise = idle acquire hands over to idle control with a larger speed error Evidence: ledger:E0453, ledger:E1461</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x224BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x339" flags="0x30">
    <title>P0068 Test - Airflow Term vs Engine Speed (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0068 (manifold pressure / airflow vs throttle) airflow leg: this curve by engine speed (600 to 7000 rpm) is compared with the curve by system voltage; when it is at or above that curve the airflow leg counts as failed. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (P0068 test) Evidence: ledger:E0457, ledger:E0899, ledger:E1522</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="600" />
      <LABEL index="1" value="1400" />
      <LABEL index="2" value="2200" />
      <LABEL index="3" value="3000" />
      <LABEL index="4" value="3800" />
      <LABEL index="5" value="4600" />
      <LABEL index="6" value="5400" />
      <LABEL index="7" value="6200" />
      <LABEL index="8" value="7000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22DAA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x33A" flags="0x30">
    <title>P0068 Test - Airflow Term vs System Voltage (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0068 (manifold pressure / airflow vs throttle) airflow leg: this curve by system voltage (6 to 14 V) is the limit the engine speed curve is compared with. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (P0068 test) Evidence: ledger:E0457, ledger:E0899, ledger:E1522</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>V</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="6" />
      <LABEL index="1" value="7" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="9" />
      <LABEL index="4" value="10" />
      <LABEL index="5" value="11" />
      <LABEL index="6" value="12" />
      <LABEL index="7" value="13" />
      <LABEL index="8" value="14" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22DBE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x33B" flags="0x30">
    <title>P0068 Fail - Pressure Difference</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0068 pressure leg: measured manifold pressure above the pressure modelled from throttle position by more than this, by intake air temperature (-40 to 152 C). P0068 sets when this leg and the airflow leg both hold for the fail time. Stock 25 kPa at every temperature. Effect: raise = a larger pressure disagreement is tolerated Evidence: ledger:E0458, ledger:E1066</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22D94" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x33C" flags="0x0">
    <title>Vehicle Speed - Min Speed for Primary Source</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this speed the vehicle speed is taken from the transmission output speed instead of the primary speed source. Stock 5.0 km/h. Effect: raise = trans-side speed used up to a higher speed Evidence: ledger:E0460</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x2006C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x33D" flags="0x0">
    <title>Speed Sensor - Pulses per Mile</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pulses the transmission output-shaft speed sensor makes per mile of travel: sensor pulses per revolution (40) x axle ratio x tire revolutions per mile. Stock 114371 = 40 x 4.56 x 627. The PCM loads it at power-up into two speed sensor timer set-ups, which divide it by 1000 x the timer prescaler. Vehicle speed itself comes from the axle ratio and tire revs, not from this value. After an axle or tire change, set it to 40 x the new axle ratio x the new tire revs per mile so it stays consistent; do not tune it on its own. Effect: keep consistent with the axle ratio and tire revs Evidence: ledger:E0461, ledger:E1575</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x20074" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>pulses/mi</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>4294967295.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x33E" flags="0x0">
    <title>Speed Sensor - Timer Prescaler</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Prescaler the PCM writes to the vehicle speed sensor input timer at power-up. Stock 20. The PCM derives the speed sensor period scale from this and the speed sensor scaling constant together, so changing it alone changes the speed reading. Raw stored value. Reference only: DO NOT EDIT. Effect: reference only (speed sensor input) Evidence: ledger:E0461, ledger:E0899</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x20070" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x33F" flags="0x0">
    <title>Swap - Theft Deterrent (VATS) Fuel Enable Bypass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Swap setting. 0 (stock): after key-on the PCM holds fuel off until the theft deterrent exchange with the body control module on the vehicle bus clears it; with no module answering, the engine cranks but never fuels. 1: the PCM skips that exchange and enables fuel at once, so a PCM moved into an engine swap runs without the donor body control module. Only the fuel enable changes; no password or security data is read or changed. For use on your own engine swap only. Effect: 1 = engine fuels and runs with no body control module; 0 = stock (fuel waits for the theft deterrent exchange) Evidence: ledger:E0461, ledger:E1652</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20506" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>0 = stock, 1 = bypass</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x340" flags="0x0">
    <title>Fuel Trim Monitor - Filtered Data Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): time of filtered trim data needed in this trip before the first lean or rich decision. Stock 20 s. Effect: raise = the first decision of a trip comes later Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D6C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x341" flags="0x0">
    <title>Fuel Trim Monitor - Lean, Short Term Trim Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): P0171 sets only when the filtered short term trim is also at or above this (1.0 = no correction). Stock 0.75. Effect: raise = a lean failure also needs a higher short term trim Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DA6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x342" flags="0x0">
    <title>Fuel Trim Monitor Enable - RPM Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while engine speed is above this. Stock 400 rpm. Narrowing the window makes the monitor run less often. Effect: raise = the monitor needs more engine speed to run Evidence: ledger:E0464, ledger:E0953</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DB6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x343" flags="0x0">
    <title>Fuel Trim Monitor Enable - RPM Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while engine speed is below this. Stock 5700 rpm. Narrowing the window makes the monitor run less often. Effect: lower = the monitor stops at a lower engine speed Evidence: ledger:E0464, ledger:E0953</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DB4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x344" flags="0x0">
    <title>Fuel Trim Monitor Enable - Barometric Pressure Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while barometric pressure is above this. Stock 70 kPa (roughly 3000 m altitude). Narrowing the window makes the monitor run less often. Effect: raise = the monitor stops running at a lower altitude Evidence: ledger:E0464, ledger:E0953</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DB8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x345" flags="0x0">
    <title>Fuel Trim Monitor Enable - Intake Air Temperature Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while intake air temperature is above this. Stock -20 C. Narrowing the window makes the monitor run less often. Effect: raise = the monitor needs warmer intake air to run Evidence: ledger:E0464, ledger:E0953</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DE6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x346" flags="0x0">
    <title>Fuel Trim Monitor Enable - MAP Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while manifold pressure is above this. Stock 11 kPa. Narrowing the window makes the monitor run less often. Effect: raise = the monitor needs more manifold pressure to run Evidence: ledger:E0464, ledger:E0953</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DBA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x347" flags="0x0">
    <title>Fuel Trim Monitor Enable - MAP Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while manifold pressure is below this. Stock 100 kPa. Narrowing the window makes the monitor run less often. Effect: lower = the monitor stops at a lower manifold pressure Evidence: ledger:E0464, ledger:E0953</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DBC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x348" flags="0x0">
    <title>Fuel Trim Monitor - Non Purge Cell Purge Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A non purge set cell (cell use 2) is only sampled by the fuel trim monitor while commanded evaporative purge is at or below this. Stock 8 %. The fuel trim monitor (P0171 system too lean, P0172 system too rich) samples the long term fuel trim cell the engine is in; cells 0 to 20 are the purge set and 21 to 38 the non purge set. Effect: raise = non purge cells are sampled with more purge flowing Evidence: ledger:E0397, ledger:E0464, ledger:E1355</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DC6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x349" flags="0x0">
    <title>Fuel Trim Monitor - Low Fuel Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): fuel level below which the low fuel guard can apply. Stock 10 %. Effect: raise = the low fuel guard applies at a higher fuel level Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DC2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x34A" flags="0x0">
    <title>Fuel Trim Monitor - Low Fuel Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): time the fuel level must stay below the low fuel level before the low fuel guard applies (the lean reading is then capped so that running out of fuel does not set P0171). Stock 30 s. Effect: raise = the low fuel guard takes longer to apply Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D70" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x34B" flags="0x0">
    <title>Fuel Trim Monitor - Cell Settle Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only samples a fuel trim cell once the engine has stayed in that cell for this many updates in a row. Stock 5. Effect: raise = the engine must stay in a trim cell longer before the monitor samples it Evidence: ledger:E0466, ledger:E0962</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D82" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x34C" flags="0x30">
    <title>Fuel Trim Monitor - Non Purge Rich Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): long term trim measured with purge off at or below which a purge-off segment counts as rich; enough rich segments set P0172. Stock 0.80. The lookup input is fixed, so only the first value is used; set all 17 the same. Effect: lower = more removed fuel is tolerated before P0172 sets Evidence: ledger:E0467, ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37E6A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x34D" flags="0x30">
    <title>Fuel Trim Monitor - Rich Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): filtered long term trim at or below which the system is suspected rich and the purge-off test is requested (0.81 = 19 % fuel removed). P0172 is decided by the purge-off test, not by this value alone. Stock 0.81. The lookup input is fixed, so only the first value is used; set all 17 the same. Effect: lower = more removed fuel is tolerated before the purge-off test is requested Evidence: ledger:E0467, ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37E46" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x34E" flags="0x30">
    <title>Fuel Trim Monitor - Lean Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): filtered long term trim at or above which the system is judged lean and P0171 sets (1.0 = no correction, 1.24 = 24 % fuel added). Stock 1.24. The lookup input is fixed, so only the first value is used; set all 17 the same. Effect: raise = more added fuel is tolerated before P0171 sets Evidence: ledger:E0467, ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37E22" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x34F" flags="0x0">
    <title>Catalyst Monitor Enable - Throttle Change Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: the test only stays active while throttle position has varied by no more than this since it started tracking. Stock 50 %. Effect: lower = smaller throttle movements stop the test Evidence: ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x350" flags="0x0">
    <title>Catalyst Monitor Enable - Airflow Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only runs while mass airflow is at or above this (with engine speed near desired idle, see the RPM Above / Below Idle limits). Stock 2.0 g/s. Effect: raise = the test needs more airflow to run Evidence: ledger:E0468, ledger:E0919, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x351" flags="0x0">
    <title>Catalyst Monitor Enable - Airflow Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only runs while mass airflow is at or below this (with engine speed near desired idle, see the RPM Above / Below Idle limits). Stock 12.0 g/s. Effect: raise = the test also runs at higher airflow Evidence: ledger:E0468, ledger:E0919, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x352" flags="0x0">
    <title>Catalyst Monitor - Purge Factor Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): the test only becomes ready once the purge factor has been ramped down to this share of full purge or lower. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (lower = the catalyst test waits for purge to be ramped further down) Evidence: ledger:E0468, ledger:E1458</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x353" flags="0x0">
    <title>Catalyst Monitor - Settle Time, Just Out of Park / Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): settle time before the test proceeds when the transmission has just come out of Park, Neutral or Reverse and the truck has not driven off since. Stock 5 s. Effect: raise = the test waits longer after a range change Evidence: ledger:E0468, ledger:E0998, ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x354" flags="0x0">
    <title>Catalyst Monitor - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): settle time at idle before the test proceeds (the shorter time, used when the truck was not just shifted out of Park, Neutral or Reverse). Stock 3 s. Effect: raise = the test waits longer at idle before it starts Evidence: ledger:E0468, ledger:E0998, ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x355" flags="0x0">
    <title>Catalyst Monitor - Closed Throttle Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: commanded throttle position, with the share used for idle air taken out, at or below this counts as closed throttle. Stock 5 %. Effect: raise = larger throttle openings still count as closed Evidence: ledger:E0999</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x356" flags="0x0">
    <title>Catalyst Monitor - New Catalyst Warm-Up Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) on a new catalyst: run time counts toward the warm-up time only while the modelled catalyst temperature is at or above this. Stock 500 C. Effect: raise = only hotter running counts toward releasing the new-catalyst delay Evidence: ledger:E0470, ledger:E1082, ledger:E1188</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345DC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>1023.984375</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/64"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x357" flags="0x0">
    <title>Catalyst Monitor - New Catalyst Warm-Up Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) on a new catalyst: the test stays off until the catalyst has spent this much time in total at or above the warm-up temperature. The total is kept between drives. Stock 3600 s (1 hour). Effect: raise = the catalyst test starts later in the life of a new catalyst Evidence: ledger:E0470, ledger:E1188</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345D8" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x358" flags="0x0">
    <title>Cruise - Brake Press Required Before Engage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Swap setting. 1 (stock): cruise control can engage only after the brake pedal has been pressed once since key on. 0: that first brake press is not required, for engine swaps whose brake switch wiring does not give the PCM this signal. Effect: 0 = cruise can engage without a first brake press; 1 = stock Evidence: ledger:E0476, ledger:E1727, ledger:E1742</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2191A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = required (stock), 0 = not required</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x359" flags="0x0">
    <title>Vehicle Speed Limiter Ramp Timer Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Enables the speed limiter&#x27;s ramp timer. When 0 the timer never counts and the ramp-time check is skipped. Stock 1 (enabled). Effect: 0 = disable the ramp timer entirely; 1 = enabled (stock) Evidence: ledger:E0482</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x31AF4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>on/off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x35A" flags="0x0">
    <title>Vehicle Speed Limiter Ramp Mode Select</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Selects how the speed limiter applies its spark retard once armed: 1 = ramps in gradually as the ramp timer builds (retard follows speed over the limit times the gear gain); 0 = skips the ramp, presets the timer and applies no retard on that pass. Stock 1 (gradual). Effect: 0 = instant timer preset with no retard this pass; 1 = gradual ramp (stock) Evidence: ledger:E0483</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x31AF2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>on/off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x35B" flags="0x0">
    <title>Vehicle Speed Limiter Ramp Timer Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Ramp time after which the speed limiter flags its ramp as complete; also the value the timer is preset to when the ramp is skipped. Stock 0.1 s. Effect: raise = longer ramp time before the limiter&#x27;s ramp-time-reached flag is set Evidence: ledger:E0483</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x31AF6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x35C" flags="0x0">
    <title>Closed Throttle Flag - Release Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM&#x27;s closed-throttle flag sets when throttle position is at or below its enter threshold (0.10 % stock) and clears again when throttle rises above that threshold plus this amount. Stock 0.10 %. Effect: raise = the throttle must open further before the closed-throttle flag clears Evidence: ledger:E0485, ledger:E0717, ledger:E0987</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x31B50" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.001526</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.34"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x35D" flags="0x0">
    <title>Closed Throttle Flag - Set Below Measured Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed throttle flag (used by the A/C compressor control to hold the compressor off just after the throttle closes): the flag can only set while the measured throttle area above the idle area is at or below this (not checked while the throttle is under idle speed control). Stock 5 %. Effect: raise = the flag may set with the throttle plate still further open Evidence: ledger:E1137</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31B52" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x35E" flags="0x0">
    <title>Fuel Trim Monitor - Purge Off Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): longest purge-off measurement; after it the attempt is abandoned. Stock 35 s. Effect: raise = purge may stay off longer in one attempt Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DF2" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x35F" flags="0x0">
    <title>Fuel Trim Monitor - Out of Cell Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): longest time during the purge-off measurement outside a usable non-purge fuel trim cell; after it the attempt is abandoned. Stock 2 s. Effect: raise = the measurement tolerates longer excursions Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DEA" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x360" flags="0x0">
    <title>Fuel Trim Monitor - Wait After an Unfinished Test</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): wait before the next test when no purge-off segment could be evaluated (wait limit or attempt limit reached). Stock 1200 s (20 minutes). Effect: raise = purge-off tests repeat less often after an unfinished one Evidence: ledger:E0498, ledger:E0898, ledger:E0900, ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DEE" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>26843545.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x361" flags="0x0">
    <title>Fuel Trim Monitor - Purge Restored Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): longest time purge runs normally between two purge-off segments; the next segment starts sooner once enough purge has flowed. Stock 30 s. Effect: raise = the pause between purge-off segments may last longer Evidence: ledger:E0499, ledger:E0898, ledger:E0900, ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D90" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x362" flags="0x0">
    <title>Fuel Trim Monitor - Unused Count (no effect)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor: read only on a path the stock program never takes (its condition flag is cleared earlier in the same pass). Changing it has no effect. Stock 100. Effect: no effect Evidence: ledger:E0499, ledger:E0898, ledger:E0900, ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D6A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x363" flags="0x0">
    <title>Fuel Trim Monitor - Short Term Trim Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): filter on the short term trim the lean and rich decisions use; each 100 ms sample moves the filtered value this fraction of the way to the new reading. Stock 0.20. Effect: raise = the filtered short term trim follows faster Evidence: ledger:E0500, ledger:E0898, ledger:E0900, ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DA4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x364" flags="0x0">
    <title>Fuel Trim Monitor - Long Term Trim Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): filter on the long term trim the lean and rich decisions use; each 100 ms sample moves the filtered value this fraction of the way to the new reading. Stock 0.16. Effect: raise = the filtered long term trim follows faster Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DA0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x365" flags="0x0">
    <title>Fuel Trim Monitor - Non Purge Trim Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): filter on the long term trim measured with purge off (used by the purge-off test); fraction per 100 ms sample. Stock 0.10. Effect: raise = the filtered non-purge trim follows faster Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DA2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x366" flags="0x0">
    <title>Traction Control Gear Request - Torque Limit Threshold A (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the traction control torque limit is below this (with vehicle speed and rpm above their thresholds), traction control requests a gear change. On this calibration the request is not applied to the shift schedule. Stock 80 Nm. Effect: no effect on the stock calibration (the gear request is not applied) Evidence: ledger:E0502, ledger:E0914, ledger:E0918, ledger:E0925, ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x302B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x367" flags="0x0">
    <title>Traction Control Gear Request - Speed Threshold A (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First request condition: vehicle speed must be above this (stock 22 km/h), with the torque limit below threshold A and engine speed above its threshold. On this calibration the request is not applied to the shift schedule (inactive). Effect: no effect on this truck Evidence: ledger:E0502, ledger:E0717, ledger:E0733, ledger:E0918, ledger:E0925, ledger:E1377</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x302B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x368" flags="0x0">
    <title>Traction Control Gear Request - RPM Threshold A (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First request condition: engine speed must be above this (stock 1800 rpm), with the torque limit below threshold A and vehicle speed above its threshold. On this calibration the request is not applied to the shift schedule (inactive). Effect: no effect on this truck Evidence: ledger:E0502, ledger:E0918, ledger:E0925, ledger:E1377</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x302B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x369" flags="0x0">
    <title>Traction Control Gear Request - Torque Limit Threshold B1 (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Second request condition: torque limit below this with its own speed and rpm thresholds. On this calibration the request is not applied to the shift schedule. Stock 125 Nm. Effect: no effect on the stock calibration (the gear request is not applied) Evidence: ledger:E0503, ledger:E0914, ledger:E0918, ledger:E0925, ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3029E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x36A" flags="0x0">
    <title>Traction Control Gear Request - Speed Threshold B1 (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Second request condition: vehicle speed must be above this (stock 22 km/h), with the torque limit below threshold B1 and engine speed above its threshold. On this calibration the request is not applied to the shift schedule (inactive). Effect: no effect on this truck Evidence: ledger:E0503, ledger:E0717, ledger:E0733, ledger:E0918, ledger:E0925, ledger:E1377</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x302A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x36B" flags="0x0">
    <title>Traction Control Gear Request - RPM Threshold B1 (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Second request condition: engine speed must be above this (stock 2400 rpm), with the torque limit below threshold B1 and vehicle speed above its threshold. On this calibration the request is not applied to the shift schedule (inactive). Effect: no effect on this truck Evidence: ledger:E0503, ledger:E0918, ledger:E0925, ledger:E1377</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x302A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x36C" flags="0x0">
    <title>Traction Control Gear Request - Torque Limit Threshold B2 (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Third request condition: torque limit below this with its own speed and rpm thresholds. On this calibration the request is not applied to the shift schedule. Stock 150 Nm. Effect: no effect on the stock calibration (the gear request is not applied) Evidence: ledger:E0503, ledger:E0914, ledger:E0918, ledger:E0925, ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x302A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x36D" flags="0x0">
    <title>Traction Control Gear Request - Speed Threshold B2 (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Third request condition: vehicle speed must be above this (stock 22 km/h), with the torque limit below threshold B2 and engine speed above its threshold. On this calibration the request is not applied to the shift schedule (inactive). Effect: no effect on this truck Evidence: ledger:E0503, ledger:E0717, ledger:E0733, ledger:E0918, ledger:E0925, ledger:E1377</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x302A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x36E" flags="0x0">
    <title>Traction Control Gear Request - RPM Threshold B2 (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Third request condition: engine speed must be above this (stock 3750 rpm), with the torque limit below threshold B2 and vehicle speed above its threshold. On this calibration the request is not applied to the shift schedule (inactive). Effect: no effect on this truck Evidence: ledger:E0503, ledger:E0918, ledger:E0925, ledger:E1377</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x302A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x36F" flags="0x0">
    <title>Engine-Off Timer Diagnostic (P2610) - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The engine-off timer diagnostic (P2610) checks that the PCM&#x27;s engine-off timer counts once per second against the PCM&#x27;s own clock: a count every 0.59 to 1.39 s is a good sample, 3 bad samples set the code and 10 samples pass it. Set to 0 the diagnostic never runs. Stock 1 (on). Effect: 0 = the engine-off timer diagnostic is switched off Evidence: ledger:E0508, ledger:E0829</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A40" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>on/off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x370" flags="0x0">
    <title>Engine-Off Timer Diagnostic (P2610) - Minimum Intake Air Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The engine-off timer diagnostic (P2610) checks that the PCM&#x27;s engine-off timer counts once per second against the PCM&#x27;s own clock: a count every 0.59 to 1.39 s is a good sample, 3 bad samples set the code and 10 samples pass it. It only runs while intake air temperature is at or above this value. Stock -40 C. Effect: raise = the engine-off timer diagnostic stops running in colder intake air Evidence: ledger:E0508, ledger:E0829</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A50" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x371" flags="0x0">
    <title>Engine-Off Timer Diagnostic (P2610) - Maximum Intake Air Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The engine-off timer diagnostic (P2610) checks that the PCM&#x27;s engine-off timer counts once per second against the PCM&#x27;s own clock: a count every 0.59 to 1.39 s is a good sample, 3 bad samples set the code and 10 samples pass it. It only runs while intake air temperature is at or below this value. Stock 125 C. Effect: lower = the engine-off timer diagnostic stops running in hotter intake air Evidence: ledger:E0508, ledger:E0829</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A52" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x372" flags="0x0">
    <title>Fuel Trim Monitor Stage Enable - RPM Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. One of the fuel trim monitor&#x27;s (P0171 system too lean, P0172 system too rich) conditions for running its test stages: engine speed must be above this. Stock 500 rpm. Narrowing the window makes the monitor run less often. Effect: raise = the monitor&#x27;s stages need more engine speed to run Evidence: ledger:E0522, ledger:E0734, ledger:E0961</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DB2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x373" flags="0x0">
    <title>Fuel Trim Monitor Stage Enable - MAP Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. One of the fuel trim monitor&#x27;s (P0171 system too lean, P0172 system too rich) conditions for running its test stages: manifold pressure must be above this. Stock 11 kPa. Narrowing the window makes the monitor run less often. Effect: raise = the monitor&#x27;s stages need more manifold pressure to run Evidence: ledger:E0522, ledger:E0734, ledger:E0961</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DC0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x374" flags="0x0">
    <title>Fuel Trim Monitor Stage Enable - MAP Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. One of the fuel trim monitor&#x27;s (P0171 system too lean, P0172 system too rich) conditions for running its test stages: manifold pressure must be below this. Stock 100 kPa. Narrowing the window makes the monitor run less often. Effect: lower = the monitor&#x27;s stages stop at a lower manifold pressure Evidence: ledger:E0522, ledger:E0734, ledger:E0961</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DBE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x375" flags="0x0">
    <title>Fuel Trim Monitor - Purge Off Attempts</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): number of times purge may be shut off before the test is sent to its long wait. Stock 30. Effect: lower = the test gives up after fewer purge shut-offs Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D72" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>attempts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x376" flags="0x30">
    <title>Fuel Trim Monitor - Purge Ramp Down Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): amount commanded purge is lowered every 100 ms when the test shuts purge off, by the purge command at the start of the ramp (0 to 100 %). Stock 199.8 % (purge off at once) up to 25 % purge, 10 % per step above. Effect: lower = purge is shut off more gradually Evidence: ledger:E0525, ledger:E0734, ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% commanded purge</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.275" />
      <LABEL index="2" value="12.55" />
      <LABEL index="3" value="18.825" />
      <LABEL index="4" value="25.1" />
      <LABEL index="5" value="31.375" />
      <LABEL index="6" value="37.65" />
      <LABEL index="7" value="43.925" />
      <LABEL index="8" value="50.2" />
      <LABEL index="9" value="56.475" />
      <LABEL index="10" value="62.75" />
      <LABEL index="11" value="69.025" />
      <LABEL index="12" value="75.3" />
      <LABEL index="13" value="81.575" />
      <LABEL index="14" value="87.85" />
      <LABEL index="15" value="94.125" />
      <LABEL index="16" value="100.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37ED6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% per step</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.781250</max>
      <MATH equation="X/326.4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x377" flags="0x0">
    <title>Fuel Trim Monitor - Purge Level During Test</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): commanded purge held while the non-purge trim is measured (the end point of the ramp down). Stock 0 %. Effect: raise = some purge keeps flowing during the purge-off measurement Evidence: ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x378" flags="0x0">
    <title>Fuel Trim Monitor - Purge Off Segment Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor (P0171 / P0172): length of one purge-off segment, counted while the non-purge trim filter is running. Stock 7 s. Effect: raise = each purge-off segment lasts longer Evidence: ledger:E1067</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D80" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x379" flags="0x0">
    <title>P1574 Check - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): the check only runs while engine speed is at or above this. Stock 500 rpm. Effect: raise = the check needs a higher engine speed Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A6C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x37A" flags="0x0">
    <title>P1574 Check - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): engine speed must have been above the rpm minimum for this long before the check starts. Stock 1 s. Effect: raise = the check starts later Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A6E" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x37B" flags="0x30">
    <title>Crank-Timed Output - Delay Compensation Time vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Delay time compensated on the crank-timed output events, by engine speed: the time is turned into crank angle at the current speed and the events are scheduled that much earlier. Stock 0.14 ms at low speed falling to 0.10 ms from 4096 rpm. Effect: raise = the crank-timed output events happen earlier at that engine speed Evidence: ledger:E0536, ledger:E1272</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1024" />
      <LABEL index="2" value="2048" />
      <LABEL index="3" value="3072" />
      <LABEL index="4" value="4096" />
      <LABEL index="5" value="5120" />
      <LABEL index="6" value="6144" />
      <LABEL index="7" value="7168" />
      <LABEL index="8" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CFA8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ms</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x37C" flags="0x30">
    <title>Idle Spark Minimum vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower limit on spark advance in idle spark mode, by coolant temperature (-40 to 120 C). The idle maximum still wins if the two cross. Stock 5 deg up to 0 C, 0 deg from 10 to 40 C, falling to -5 deg from 80 C. Effect: raise = higher spark advance floor at idle Evidence: ledger:E0543, ledger:E0718, ledger:E1219</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-39.998" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20.002" />
      <LABEL index="3" value="-10.004" />
      <LABEL index="4" value="-0.006" />
      <LABEL index="5" value="9.992" />
      <LABEL index="6" value="19.99" />
      <LABEL index="7" value="29.988" />
      <LABEL index="8" value="39.986" />
      <LABEL index="9" value="49.984" />
      <LABEL index="10" value="59.982" />
      <LABEL index="11" value="69.98" />
      <LABEL index="12" value="79.978" />
      <LABEL index="13" value="89.976" />
      <LABEL index="14" value="99.974" />
      <LABEL index="15" value="109.972" />
      <LABEL index="16" value="119.97" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EABA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x37D" flags="0x0">
    <title>EVAP Engine-Off Test - Re-Vent Count Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: number of re-vents allowed in the vacuum phase; one more ends the test with what it has. Stock 3. Effect: raise = more re-vents are allowed before the test is ended Evidence: ledger:E1050</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35760" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x37E" flags="0x0">
    <title>EVAP Engine-Off Service Test - Result Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP service test (the scan tool started version of the leak test): how long the finished test holds its result before it ends. Stock 600 s. Effect: raise = the service test stays in its final step longer Evidence: ledger:E0554, ledger:E1055</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35CC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x37F" flags="0x0">
    <title>Ambient Air Temp Estimate - Flush Minimum Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The flush requirement only runs down while mass airflow is at or above this (stock 5 g/s) and vehicle speed is at or above its minimum. The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it down, and until it reaches zero the estimate can only fall toward the intake air temperature. Effect: raise = more airflow is needed before driving counts toward releasing the ambient estimate Evidence: ledger:E0385, ledger:E0555, ledger:E1...</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x35CEA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x380" flags="0x0">
    <title>Ambient Air Temp Estimate - Flush Minimum Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The flush requirement only runs down while vehicle speed is at or above this (stock 48.3 km/h = 30 mph) and airflow is at or above its minimum. The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it down, and until it reaches zero the estimate can only fall toward the intake air temperature. Effect: raise = a higher speed is needed before driving counts toward releasing the ambient estimate Evidence: ledger:E0385, ledger:E0555,...</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x35CEC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x381" flags="0x30">
    <title>Ambient Air Temp Estimate - Flush Rate Weight vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the flush requirement runs down, by mass airflow (0 to 128 g/s): 1.0 takes one second of requirement off per second of qualifying driving, 2.0 two seconds. Stock 1.0 everywhere. The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it down, and until it reaches zero the estimate can only fall toward the intake air temperature. Effect: raise = the ambient estimate is released sooner at that airflow Evidence: ledger:E0385,...</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="8" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="24" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="48" />
      <LABEL index="7" value="56" />
      <LABEL index="8" value="64" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="88" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="104" />
      <LABEL index="14" value="112" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35CF0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x382" flags="0x30">
    <title>EVAP Engine-Off Tank Vacuum Jump Window - Upper</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Change in filtered tank vacuum between updates, by fuel level (0 to 100 %), that is the upper edge of the window that sets the main tank vacuum jump flag during the engine-off test. Stock 32 inH2O in every cell, which is never reached. Effect: lower = the upper edge of the engine-off jump window comes down Evidence: ledger:E0556, ledger:E0899, ledger:E0935, ledger:E0937, ledger:E0940, ledger:E0944, ledger:E1054</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3603A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>inH2O</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x383" flags="0x0">
    <title>DFCO - Catalyst Hot Temperature (Short Delay)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or above this catalyst model temperature the short fuel cut delay is used (stock 885 C). Deceleration fuel cut (DFCO): once all the fuel cut conditions hold, fuel is cut only after this delay; the delay restarts whenever the conditions drop out or the gear changes. The catalyst-hot state is set when the catalyst model temperature reaches the hot temperature and lasts until the next fuel cut request. Effect: lower = the short delay is used from a cooler catalyst Evidence: ledger:E0549, ledger:E1382</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F152" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x384" flags="0x30">
    <title>Dwell Multiplier vs Cam-Phase Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies coil dwell (base dwell times the voltage and coolant modifier) by the cam-phase factor (Cam-Phase Factor vs Cam Angle and RPM). Ten points from 0 to 0.27 in 0.03 steps; above 0.27 the last point is used. Stock 1.0 everywhere (no effect). Effect: raise = longer coil dwell at that cam-phase factor Evidence: ledger:E0550, ledger:E0884</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>cam-phase factor</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.03" />
      <LABEL index="2" value="0.06" />
      <LABEL index="3" value="0.09" />
      <LABEL index="4" value="0.12" />
      <LABEL index="5" value="0.15" />
      <LABEL index="6" value="0.18" />
      <LABEL index="7" value="0.21" />
      <LABEL index="8" value="0.24" />
      <LABEL index="9" value="0.27" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F7DC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x385" flags="0x30">
    <title>Spark Floor vs RPM (alternate mode A)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest spark advance allowed, by rpm, while alternate spark mode A (a run condition set elsewhere in the PCM) is active. Spark below it is raised to it. Stock -15 deg at every rpm. Effect: raise = spark is never allowed below a higher advance Evidence: ledger:E0552, ledger:E0718, ledger:E0724</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30174" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x386" flags="0x30">
    <title>Spark Floor vs RPM (alternate mode B)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest spark advance allowed, by rpm, while alternate spark mode B (a run condition set elsewhere in the PCM; mode A takes priority) is active. Spark below it is raised to it. Stock -20 deg at every rpm. Effect: raise = spark is never allowed below a higher advance Evidence: ledger:E0552, ledger:E0718, ledger:E0724</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x301BC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x387" flags="0x30">
    <title>Spark Floor vs RPM (default)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest spark advance allowed, by rpm, in normal running. Spark below it is raised to it. Stock -15 deg at every rpm. (E0724) Effect: raise = spark is never allowed below a higher advance Evidence: ledger:E0552, ledger:E0718, ledger:E0724</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3012C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x388" flags="0x30">
    <title>Airflow Transient - Change Threshold vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Diagnostic airflow transient check: a sample counts as transient when the airflow change since the previous sample is at or above this, by airflow (0 to 400 g/s). Stock 10 g/s at idle airflow rising to 30 g/s at 400 g/s. Effect: raise = larger airflow changes needed before a sample counts as transient Evidence: ledger:E0563, ledger:E1269</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>g/s (airflow)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="25" />
      <LABEL index="2" value="50" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="100" />
      <LABEL index="5" value="125" />
      <LABEL index="6" value="150" />
      <LABEL index="7" value="175" />
      <LABEL index="8" value="200" />
      <LABEL index="9" value="225" />
      <LABEL index="10" value="250" />
      <LABEL index="11" value="275" />
      <LABEL index="12" value="300" />
      <LABEL index="13" value="325" />
      <LABEL index="14" value="350" />
      <LABEL index="15" value="375" />
      <LABEL index="16" value="400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x386AE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x389" flags="0x0">
    <title>MAP Plausibility - Fail Count (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: the check&#x27;s enable is off, so it never runs. MAP plausibility check: every sample in which manifold pressure is above the high limit or below the low limit for the current engine speed and throttle area counts as out of band. When the out-of-band count reaches the fail count, the window ends as a failure; when the window reaches its sample count first, it ends as a pass. The high limit tops out near 104 kPa, so sustained boost would be counted out of band, but the check sets no code. This is the out-of-band sample count that ends a window as a failure. Stock 80. Effect: raise = more out...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38868" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x38A" flags="0x0">
    <title>MAP Plausibility - Window Samples (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: the check&#x27;s enable is off, so it never runs. MAP plausibility check: every sample in which manifold pressure is above the high limit or below the low limit for the current engine speed and throttle area counts as out of band. When the out-of-band count reaches the fail count, the window ends as a failure; when the window reaches its sample count first, it ends as a pass. The high limit tops out near 104 kPa, so sustained boost would be counted out of band, but the check sets no code. This is the number of samples in a window. Stock 100. Effect: raise = longer windows (keep above the fai...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3886A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x38B" flags="0x30">
    <title>MAP Sensor Fault Substitute - Throttle Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the MAP sensor has failed, the PCM uses a modelled manifold pressure instead: the throttle term (throttle area times the throttle curve) plus the engine speed term, capped at 90 kPa. This curve is the throttle term&#x27;s gain by engine speed: kPa of substitute pressure per percent of throttle area. Effect: raise = substitute manifold pressure rises faster with throttle at that engine speed Evidence: ledger:E0166, ledger:E0567, ledger:E0716, ledger:E0839</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>26</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CAF6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa per % throttle area</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>20.479375</max>
      <MATH equation="X/3200.0488"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x38C" flags="0x30">
    <title>MAP Sensor Fault Substitute - Engine Speed Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the MAP sensor has failed, the PCM uses a modelled manifold pressure instead: the throttle term (throttle area times the throttle curve) plus the engine speed term, capped at 90 kPa. This curve is the engine speed term, added directly. Stock 96 kPa with the engine stopped, falling to 7.5 kPa at higher engine speed. Effect: raise = higher substitute manifold pressure at that engine speed Evidence: ledger:E0166, ledger:E0567, ledger:E0716, ledger:E0839</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>26</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CAC0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x38D" flags="0x0">
    <title>Catalyst Monitor - Idle RPM Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: engine speed below this counts as idle; time spent at or above it counts as driving. Stock 950 rpm. Effect: raise = higher engine speeds still count as idle Evidence: ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x38E" flags="0x0">
    <title>P0116 Test Enable - Engine Off Soak Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116): only runs after the engine has been off for longer than this. Stock 28800 s (8 hours). Effect: lower = the test also runs after a shorter soak Evidence: ledger:E1011</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35180" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x38F" flags="0x0">
    <title>P0125 / P0128 Check - Intake Air Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: the checks are skipped for the trip once the lowest intake air temperature seen since start is below this. Stock -6.75 degC. Effect: lower = the checks also run in colder weather Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3518C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x390" flags="0x0">
    <title>P0125 / P0128 Check - Engine Run Time Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: an instance that has not started by this engine run time is skipped for the trip. Stock 1800 s. Effect: raise = the checks may still start later in the trip Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35188" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x391" flags="0x0">
    <title>P0125 / P0128 Check - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: the checks become active once the engine has run this long. Stock 30 s. Effect: raise = the checks become active later Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3518A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x392" flags="0x0">
    <title>P0125 / P0128 Check - Distance Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: the distance they require only counts while vehicle speed is at or above this. Stock 3 km/h. Effect: raise = slow driving no longer counts toward the distance Evidence: ledger:E0582, ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35190" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x393" flags="0x0">
    <title>Idle Gate - Accumulated Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the idle monitor gate&#x27;s timer must accumulate before it completes and sets its done flag (stock 2.0 s). The timer only runs while the gate&#x27;s start conditions hold. Effect: raise = the gate needs longer before it completes Evidence: ledger:E0307, ledger:E0584, ledger:E1438</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35148" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x394" flags="0x0">
    <title>Diagnostic Model - Engine Speed Input Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Diagnostic model: three channels that rise toward a target set by engine speed and airflow and fall back when they drop, with a fixed value while coolant is cold. Its only readers are the misfire monitor enable conditions, a diagnostic timer and the secondary air routine; it does not limit torque, spark, fuel or throttle. Engine speed above this counts as this speed. Changing it moves when the misfire monitor runs. Stock 4000 rpm. Effect: moves when the misfire monitor and related diagnostics are enabled Evidence: ledger:E0588, ledger:E0852</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3523A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x395" flags="0x0">
    <title>Diagnostic Model - Airflow Input Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Diagnostic model: three channels that rise toward a target set by engine speed and airflow and fall back when they drop, with a fixed value while coolant is cold. Its only readers are the misfire monitor enable conditions, a diagnostic timer and the secondary air routine; it does not limit torque, spark, fuel or throttle. Airflow above this counts as this airflow. Changing it moves when the misfire monitor runs. Stock 50 g/s. Effect: moves when the misfire monitor and related diagnostics are enabled Evidence: ledger:E0588, ledger:E0852</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3523C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x396" flags="0x0">
    <title>Idle Area Command - Value at Full Throttle Area</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle airflow area command value that corresponds to full throttle area: the requested idle throttle area is the command divided by this (then limited by Idle Throttle Area Maximum). Stock 100 %, so a command of 2 % requests 2 % of full throttle area. Effect: raise = the same idle command opens the throttle less Evidence: ledger:E0589, ledger:E1445</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x23F46" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>182.041667</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/360"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x397" flags="0x0">
    <title>Idle Throttle Area Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle airflow control&#x27;s throttle area request is capped at this percentage of full throttle area. Stock 2.82 %. Effect: raise = the idle control can open the throttle further Evidence: ledger:E0282, ledger:E0589, ledger:E0924</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x23EE2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x398" flags="0x0">
    <title>Traction Control - Throttle Area Raise Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While traction control is cutting fuel, the throttle area may be raised to the traction control request, but no higher than this. Stock 2.82 %. The traction control fuel cut is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0590, ledger:E1198, ledger:E1199</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23F44" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x399" flags="0x30">
    <title>Throttle Area Limit vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Ceiling on the commanded throttle area (percent of full area) by engine speed (0 to 8192 rpm), multiplied by the intake air and barometric pressure factors. Stock 100 % (no limit). Effect: lower = caps the commanded throttle area at that engine speed Evidence: ledger:E0452, ledger:E0590, ledger:E1198</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23EEA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle area</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x39A" flags="0x30">
    <title>Throttle Area Limit Factor vs Intake Air Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the throttle area limit by engine speed, by intake air temperature (-40 to 152 C). 1.0 = no change. Stock 1.0 everywhere. Effect: lower = lowers the throttle area limit in that condition Evidence: ledger:E0591, ledger:E1197, ledger:E1198</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (intake air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23F32" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x39B" flags="0x30">
    <title>Throttle Area Limit Factor vs Barometric Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the throttle area limit by engine speed, by barometric pressure (60 to 105 kPa). 1.0 = no change. Stock 1.0 everywhere. Effect: lower = lowers the throttle area limit in that condition Evidence: ledger:E0591, ledger:E1197, ledger:E1198</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (barometric pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="60" />
      <LABEL index="1" value="62.812" />
      <LABEL index="2" value="65.625" />
      <LABEL index="3" value="68.438" />
      <LABEL index="4" value="71.25" />
      <LABEL index="5" value="74.062" />
      <LABEL index="6" value="76.875" />
      <LABEL index="7" value="79.688" />
      <LABEL index="8" value="82.5" />
      <LABEL index="9" value="85.312" />
      <LABEL index="10" value="88.125" />
      <LABEL index="11" value="90.938" />
      <LABEL index="12" value="93.75" />
      <LABEL index="13" value="96.562" />
      <LABEL index="14" value="99.375" />
      <LABEL index="15" value="102.188" />
      <LABEL index="16" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23F0E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x39C" flags="0x30">
    <title>Accelerator Pedal Filter - Gain vs Pedal Gap, Rising</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain while the pedal is rising (pedal demand at or above the filtered pedal), by the gap between pedal demand and the filtered pedal. Above the hold gap the highest gain reached is kept until the gap shrinks or the direction changes. Stock 1.0 everywhere. Part of the accelerator pedal filter: the filtered pedal closes this share of its gap to the pedal demand every update; 1.0 follows the pedal at once. Effect: lower = the filtered pedal follows the pedal more slowly at that gap Evidence: ledger:E0330, ledger:E0593, ledger:E1190</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x24002" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% (pedal gap)</units>
      <embedinfo type="1" />
      <MATH equation="X/682.67"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23FDE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x39D" flags="0x30">
    <title>Accelerator Pedal Filter - Gain vs Pedal Gap, Falling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain while the pedal is falling (pedal demand below the filtered pedal), by the gap between pedal demand and the filtered pedal. Above the hold gap the highest gain reached is kept until the gap shrinks or the direction changes. Stock 1.0 everywhere. Part of the accelerator pedal filter: the filtered pedal closes this share of its gap to the pedal demand every update; 1.0 follows the pedal at once. Effect: lower = the filtered pedal follows the pedal more slowly at that gap Evidence: ledger:E0330, ledger:E0593, ledger:E1190</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x2404C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>17</indexcount>
      <units>% (pedal gap)</units>
      <embedinfo type="1" />
      <MATH equation="X/682.67"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24028" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x39E" flags="0x30">
    <title>Pedal Throttle Request Factor vs Cam-Phase Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the driver&#x27;s pedal throttle request, by the cam-phase factor (0 to 0.5; the Cam-Phase Factor vs Cam Angle and RPM table, stock up to 0.24). The PCM multiplies the pedal map&#x27;s throttle request by this and several other factors. 1.0 = no change; lower = less throttle for the same pedal. Stock 1.0 everywhere. Effect: lower = less throttle for the same pedal when the cam-phase factor is at that value Evidence: ledger:E0594, ledger:E0881, ledger:E0947, ledger:E1195</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>cam-phase factor (fraction)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.031" />
      <LABEL index="2" value="0.062" />
      <LABEL index="3" value="0.094" />
      <LABEL index="4" value="0.125" />
      <LABEL index="5" value="0.156" />
      <LABEL index="6" value="0.188" />
      <LABEL index="7" value="0.219" />
      <LABEL index="8" value="0.25" />
      <LABEL index="9" value="0.281" />
      <LABEL index="10" value="0.312" />
      <LABEL index="11" value="0.344" />
      <LABEL index="12" value="0.375" />
      <LABEL index="13" value="0.406" />
      <LABEL index="14" value="0.438" />
      <LABEL index="15" value="0.469" />
      <LABEL index="16" value="0.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23188" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x39F" flags="0x30">
    <title>Pedal Throttle Request Factor vs Barometric Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the driver&#x27;s pedal throttle request, by barometric pressure (60 to 105 kPa). The PCM multiplies the pedal map&#x27;s throttle request by this and several other factors. 1.0 = no change; lower = less throttle for the same pedal. Stock 1.0 everywhere. Effect: lower = less throttle for the same pedal at that barometric pressure Evidence: ledger:E0595, ledger:E0947, ledger:E1197</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (barometric pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="60" />
      <LABEL index="1" value="62.812" />
      <LABEL index="2" value="65.625" />
      <LABEL index="3" value="68.438" />
      <LABEL index="4" value="71.25" />
      <LABEL index="5" value="74.062" />
      <LABEL index="6" value="76.875" />
      <LABEL index="7" value="79.688" />
      <LABEL index="8" value="82.5" />
      <LABEL index="9" value="85.312" />
      <LABEL index="10" value="88.125" />
      <LABEL index="11" value="90.938" />
      <LABEL index="12" value="93.75" />
      <LABEL index="13" value="96.562" />
      <LABEL index="14" value="99.375" />
      <LABEL index="15" value="102.188" />
      <LABEL index="16" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23164" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3A0" flags="0x30">
    <title>Pedal Gain Reduction - Request Factor Cut vs Pedal</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Amount taken off the pedal throttle request factor when the pedal gain reduction starts, by pedal position (0 to 100 %). The cut is applied once per event and the factor is not cut below the Request Factor Floor. Stock 0 everywhere, and the floor is 1.0, so the reduction cuts nothing on the stock file. Effect: raise = the pedal gain reduction cuts the pedal request more at that pedal position Evidence: ledger:E0596, ledger:E1118, ledger:E1206</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23206" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3A1" flags="0x30">
    <title>Pedal Gain Increase vs Launch Acceleration Shortfall</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal gain increase target by how far the launch fell short of the pedal gain reduction acceleration threshold (threshold divided by measured acceleration, averaged over the samples: 1.0 = on the threshold, 2.0 = half of it). Values below 1.0 count as 1.0. The result is filtered, weighted by the Speed Weight and capped by the Pedal Request Factor Ceiling. Stock 1.0 everywhere, and the learn does not run on stock. Effect: raise = more pedal gain when the truck launches slower than the acceleration threshold Evidence: ledger:E0597, ledger:E1203, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>threshold / measured acceleration</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.5" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="1.5" />
      <LABEL index="4" value="2" />
      <LABEL index="5" value="2.5" />
      <LABEL index="6" value="3" />
      <LABEL index="7" value="3.5" />
      <LABEL index="8" value="4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2323E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3A2" flags="0x30">
    <title>Pedal Gain Increase - Speed Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the pedal gain increase (the amount the pedal gain is raised above 1.0) that is applied, by vehicle speed (0 to 64 km/h). Stock 1.0 (all of it). The increase itself is 1.0 everywhere in the stock calibration, so this has no effect until the increase is raised. Effect: lower = less of the pedal gain increase is used at that vehicle speed Evidence: ledger:E0597, ledger:E1195, ledger:E1200</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23256" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3A3" flags="0x30">
    <title>Pedal Response Change - Wide Open Vacuum Threshold vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal response changes (pedal map selection and any raise of the pedal request factor) are only taken while the pedal is at rest or wide open. Above the Wide Open Pedal Threshold, the pedal counts as wide open while manifold vacuum is below this value at the current engine speed. Stock 10.0 kPa at all speeds. Effect: raise = the pedal counts as wide open at a higher manifold vacuum at that rpm Evidence: ledger:E0598, ledger:E0792, ledger:E0805, ledger:E1209</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23DBE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3A4" flags="0x0">
    <title>Fuel Level Filter Start Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the PCM waits after the fuel level filter is reset before it starts filtering fuel level, and with it the fuel level jump check the EVAP leak test uses. Stock 1.0 s. Effect: raise = fuel level filtering and the EVAP fuel level jump check start later Evidence: ledger:E0217, ledger:E0599, ledger:E0942</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3729A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3A5" flags="0x0">
    <title>EVAP Vapour Reference at Full Tank</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP test vapour reference with a full tank. The PCM blends linearly from this value (full) to the empty-tank value by fuel level, and the EVAP leak test tables are looked up by the result, so this sets which rows of those tables apply at each fuel level. Stock 3003. Shown raw. DO NOT EDIT. Effect: raise = the blended result starts higher; lower = it starts lower Evidence: ledger:E0599, ledger:E0899, ledger:E0941, ledger:E0944</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x372A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3A6" flags="0x0">
    <title>EVAP Vapour Reference at Empty Tank</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP test vapour reference with an empty tank. The PCM blends linearly from the full-tank value to this value (empty) by fuel level, and the EVAP leak test tables are looked up by the result, so this sets which rows of those tables apply at each fuel level. Stock 25582. Shown raw. DO NOT EDIT. Effect: raise = the blended result can reach higher; lower = it is capped lower Evidence: ledger:E0599, ledger:E0899, ledger:E0941, ledger:E0944</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3729C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3A7" flags="0x30">
    <title>EVAP Test Fuel Level Jump Limit A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest change in filtered fuel level between updates that the EVAP leak test tolerates, by fuel level. A bigger jump (either direction) sets a fuel level jump flag, and the EVAP leak test routines pause or restart while it is set. Stock 100 % everywhere, so the flag never sets. Effect: lower = smaller fuel level jumps pause or restart the EVAP leak test Evidence: ledger:E0600, ledger:E0935</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37254" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% fuel level change</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3A8" flags="0x30">
    <title>EVAP Test Fuel Level Jump Limit B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest change in filtered fuel level between updates that the EVAP leak test tolerates, by fuel level. A bigger jump (either direction) sets a fuel level jump flag, and the EVAP leak test routines pause or restart while it is set. Stock 100 % everywhere, so the flag never sets. Effect: lower = smaller fuel level jumps pause or restart the EVAP leak test Evidence: ledger:E0600, ledger:E0935</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37278" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% fuel level change</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3A9" flags="0x30">
    <title>EVAP Test Vehicle Speed Drop Limit A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest vehicle speed drop between updates that the EVAP leak test tolerates, by vehicle speed. A bigger drop sets a speed jump flag and the leak test restarts its count. Stock -100 km/h per update, so it never acts. Effect: raise (toward 0) = smaller speed drops pause or restart the EVAP leak test Evidence: ledger:E0601, ledger:E0734, ledger:E0935, ledger:E1217</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (vehicle speed x128)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <LABEL index="11" value="110" />
      <LABEL index="12" value="120" />
      <LABEL index="13" value="130" />
      <LABEL index="14" value="140" />
      <LABEL index="15" value="150" />
      <LABEL index="16" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x372A6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per update</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3AA" flags="0x30">
    <title>EVAP Test Vehicle Speed Drop Limit B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest vehicle speed drop between updates that the EVAP leak test tolerates, by vehicle speed. Checked only past Limit A: a drop beyond this holds the leak test steps and its purge flow count instead. Stock -100 km/h per update, so it never acts. Effect: raise (toward 0) = smaller speed drops hold off the EVAP leak test Evidence: ledger:E0601, ledger:E0734, ledger:E0935, ledger:E1217</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (vehicle speed x128)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <LABEL index="11" value="110" />
      <LABEL index="12" value="120" />
      <LABEL index="13" value="130" />
      <LABEL index="14" value="140" />
      <LABEL index="15" value="150" />
      <LABEL index="16" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37312" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per update</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3AB" flags="0x30">
    <title>EVAP Test Vehicle Speed Rise Limit A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest vehicle speed rise between updates that the EVAP leak test tolerates, by vehicle speed. A bigger rise sets a speed jump flag and the leak test restarts its count. Stock +100 km/h per update, so it never acts. Effect: lower = smaller speed rises pause or restart the EVAP leak test Evidence: ledger:E0601, ledger:E0734, ledger:E0935, ledger:E1217</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (vehicle speed x128)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <LABEL index="11" value="110" />
      <LABEL index="12" value="120" />
      <LABEL index="13" value="130" />
      <LABEL index="14" value="140" />
      <LABEL index="15" value="150" />
      <LABEL index="16" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x372CA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per update</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3AC" flags="0x30">
    <title>EVAP Test Vehicle Speed Rise Limit B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest vehicle speed rise between updates that the EVAP leak test tolerates, by vehicle speed. Checked only past Limit A: a rise beyond this holds the leak test steps and its purge flow count instead. Stock +100 km/h per update, so it never acts. Effect: lower = smaller speed rises hold off the EVAP leak test Evidence: ledger:E0601, ledger:E0734, ledger:E0935, ledger:E1217</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (vehicle speed x128)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <LABEL index="11" value="110" />
      <LABEL index="12" value="120" />
      <LABEL index="13" value="130" />
      <LABEL index="14" value="140" />
      <LABEL index="15" value="150" />
      <LABEL index="16" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x372EE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per update</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3AD" flags="0x0">
    <title>P0496 Pass - Time, Cold Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve leak check (P0496): time with purge off without the vacuum limit being exceeded that passes the check, cold start. Stock 60 s. Effect: raise = the check runs longer before it passes Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37372" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3AE" flags="0x30">
    <title>EVAP Leak Test Settle Time Limit - Low Range</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP leak test, before the vacuum hold is timed: while tank vacuum is still above the settle level, the PCM waits up to this long before it takes the starting vacuum reading, then starts timing the decay. The axis covers the lower half of the EVAP test reference value (the EVAP vapour reference, which the PCM derives from fuel level: the axis labels give the fuel level on stock settings, n/a = not reached). Stock 40 s everywhere. Not used by the stock calibration: this belongs to the engine-running small leak phase, which the stock calibration switches off (small leaks are checked by the engine-off test instead). Effect: no e...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>% fuel level (stock settings)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="n/a" />
      <LABEL index="1" value="n/a" />
      <LABEL index="2" value="n/a" />
      <LABEL index="3" value="100" />
      <LABEL index="4" value="95" />
      <LABEL index="5" value="91" />
      <LABEL index="6" value="86" />
      <LABEL index="7" value="82" />
      <LABEL index="8" value="77" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="68" />
      <LABEL index="11" value="63" />
      <LABEL index="12" value="59" />
      <LABEL index="13" value="54" />
      <LABEL index="14" value="50" />
      <LABEL index="15" value="45" />
      <LABEL index="16" value="41" />
      <LABEL index="17" value="36" />
      <LABEL index="18" value="32" />
      <LABEL index="19" value="27" />
      <LABEL index="20" value="23" />
      <LABEL index="21" value="18" />
      <LABEL index="22" value="14" />
      <LABEL index="23" value="9" />
      <LABEL index="24" value="4" />
      <LABEL index="25" value="0" />
      <LABEL index="26" value="n/a" />
      <LABEL index="27" value="n/a" />
      <LABEL index="28" value="n/a" />
      <LABEL index="29" value="n/a" />
      <LABEL index="30" value="n/a" />
      <LABEL index="31" value="n/a" />
      <LABEL index="32" value="n/a" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3785C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3AF" flags="0x30">
    <title>EVAP Leak Test Settle Time Limit - High Range</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP leak test, before the vacuum hold is timed: while tank vacuum is still above the settle level, the PCM waits up to this long before it takes the starting vacuum reading, then starts timing the decay. The axis covers the upper half of the EVAP test reference value (the EVAP vapour reference; with stock settings it never reaches this range, so this curve is not used). Stock 40 s everywhere. Not used by the stock calibration: this belongs to the engine-running small leak phase, which the stock calibration switches off (small leaks are checked by the engine-off test instead). Effect: no effect in the stock calibration Eviden...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>% fuel level (stock settings)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="n/a" />
      <LABEL index="1" value="n/a" />
      <LABEL index="2" value="n/a" />
      <LABEL index="3" value="n/a" />
      <LABEL index="4" value="n/a" />
      <LABEL index="5" value="n/a" />
      <LABEL index="6" value="n/a" />
      <LABEL index="7" value="n/a" />
      <LABEL index="8" value="n/a" />
      <LABEL index="9" value="n/a" />
      <LABEL index="10" value="n/a" />
      <LABEL index="11" value="n/a" />
      <LABEL index="12" value="n/a" />
      <LABEL index="13" value="n/a" />
      <LABEL index="14" value="n/a" />
      <LABEL index="15" value="n/a" />
      <LABEL index="16" value="n/a" />
      <LABEL index="17" value="n/a" />
      <LABEL index="18" value="n/a" />
      <LABEL index="19" value="n/a" />
      <LABEL index="20" value="n/a" />
      <LABEL index="21" value="n/a" />
      <LABEL index="22" value="n/a" />
      <LABEL index="23" value="n/a" />
      <LABEL index="24" value="n/a" />
      <LABEL index="25" value="n/a" />
      <LABEL index="26" value="n/a" />
      <LABEL index="27" value="n/a" />
      <LABEL index="28" value="n/a" />
      <LABEL index="29" value="n/a" />
      <LABEL index="30" value="n/a" />
      <LABEL index="31" value="n/a" />
      <LABEL index="32" value="n/a" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x378A4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3B0" flags="0x0">
    <title>EVAP Test - Purge Step per Update</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test: largest change of commanded purge per 100 ms while the test controls purge (pull-down and ramp down). Stock 1 %. Effect: raise = purge changes faster during the test Evidence: ledger:E0605, ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37384" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3B1" flags="0x30">
    <title>EVAP Test Vacuum Pull-Down - Proportional Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Purge valve opening added per inH2O that the tank vacuum is short of the test vacuum. Stock 0 at the first point, then 8.6 rising to 20.4 % per inH2O; about 15.5 at the fixed stock reference. Used by the EVAP leak test while it pulls the tank down to its test vacuum; the purge valve is driven by this controller instead of the normal purge command (rate limited around it). Effect: raise = faster, more aggressive pull-down (more overshoot) Evidence: ledger:E0606, ledger:E1488</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>EVAP test vapour reference (raw)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1600" />
      <LABEL index="3" value="2400" />
      <LABEL index="4" value="3200" />
      <LABEL index="5" value="4000" />
      <LABEL index="6" value="4800" />
      <LABEL index="7" value="5600" />
      <LABEL index="8" value="6400" />
      <LABEL index="9" value="7200" />
      <LABEL index="10" value="8000" />
      <LABEL index="11" value="8800" />
      <LABEL index="12" value="9600" />
      <LABEL index="13" value="10400" />
      <LABEL index="14" value="11200" />
      <LABEL index="15" value="12000" />
      <LABEL index="16" value="12800" />
      <LABEL index="17" value="13600" />
      <LABEL index="18" value="14400" />
      <LABEL index="19" value="15200" />
      <LABEL index="20" value="16000" />
      <LABEL index="21" value="16800" />
      <LABEL index="22" value="17600" />
      <LABEL index="23" value="18400" />
      <LABEL index="24" value="19200" />
      <LABEL index="25" value="20000" />
      <LABEL index="26" value="20800" />
      <LABEL index="27" value="21600" />
      <LABEL index="28" value="22400" />
      <LABEL index="29" value="23200" />
      <LABEL index="30" value="24000" />
      <LABEL index="31" value="24800" />
      <LABEL index="32" value="25600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x378EC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%/inH2O</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>64.250000</max>
      <MATH equation="X/1020"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3B2" flags="0x30">
    <title>EVAP Test Vacuum Pull-Down - Integral Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Purge valve opening added per second for each inH2O that the tank vacuum is short of the test vacuum. Stock 0 at the first point, then 2.7 rising to 6.4 % per inH2O per second; about 4.9 at the fixed stock reference. Used by the EVAP leak test while it pulls the tank down to its test vacuum; the purge valve is driven by this controller instead of the normal purge command (rate limited around it). Effect: raise = the remaining vacuum error is closed faster Evidence: ledger:E0606, ledger:E1488</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>EVAP test vapour reference (raw)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1600" />
      <LABEL index="3" value="2400" />
      <LABEL index="4" value="3200" />
      <LABEL index="5" value="4000" />
      <LABEL index="6" value="4800" />
      <LABEL index="7" value="5600" />
      <LABEL index="8" value="6400" />
      <LABEL index="9" value="7200" />
      <LABEL index="10" value="8000" />
      <LABEL index="11" value="8800" />
      <LABEL index="12" value="9600" />
      <LABEL index="13" value="10400" />
      <LABEL index="14" value="11200" />
      <LABEL index="15" value="12000" />
      <LABEL index="16" value="12800" />
      <LABEL index="17" value="13600" />
      <LABEL index="18" value="14400" />
      <LABEL index="19" value="15200" />
      <LABEL index="20" value="16000" />
      <LABEL index="21" value="16800" />
      <LABEL index="22" value="17600" />
      <LABEL index="23" value="18400" />
      <LABEL index="24" value="19200" />
      <LABEL index="25" value="20000" />
      <LABEL index="26" value="20800" />
      <LABEL index="27" value="21600" />
      <LABEL index="28" value="22400" />
      <LABEL index="29" value="23200" />
      <LABEL index="30" value="24000" />
      <LABEL index="31" value="24800" />
      <LABEL index="32" value="25600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37934" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%/inH2O/s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>128.500000</max>
      <MATH equation="X/510"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3B3" flags="0x0">
    <title>Diagnostic Result Gate - Time Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A diagnostic check compares its own timer with this when it chooses its result (the trouble code it reports and its pass / fail flag). Stock 6.0 s. Effect: raise = the check waits longer before its result Evidence: ledger:E0607, ledger:E1265</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x203EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3B4" flags="0x30">
    <title>Warm-Up Time vs Startup Coolant Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum engine run time by start-up coolant temperature (-40 to 140 C in 20 C steps); the warm-up flag is set while run time is below it. Stock 5, 4, 3, 2 s at -40, -20, 0, 20 C, then 1 s. Effect: raise = the warm-up gate stays true longer at that coolant temperature Evidence: ledger:E0609, ledger:E1184</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <LABEL index="9" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x299A0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3B5" flags="0x0">
    <title>Tip-In Torque Ramp - Fast Step Vehicle Speed Trigger</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. After a shunt and swing back, the fast step also starts once vehicle speed rises faster than this per update. Stock 60 km/h per update (effectively off). Effect: tip-in torque management Evidence: ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21054" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h per update</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3B6" flags="0x30">
    <title>Starter - Cut-Out RPM vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM treats the engine as started, and turns the starter relay off, once engine speed has stayed above this for a short confirmation count, by coolant temperature. Stock 550 rpm at -40 C falling to 400 rpm from 56 C. Effect: raise = the starter stays engaged to a higher engine speed Evidence: ledger:E1024, ledger:E1288</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30230" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3B7" flags="0x30">
    <title>Starter - Cut-Out Confirmation Revolutions vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The engine counts as started, and the starter is released, once it has turned more than this many revolutions above the starter cut-out engine speed, by coolant temperature. Stock 2 at -40 to -16 C, 1 above. Effect: raise = the engine must turn more revolutions above the cut-out speed before it counts as started Evidence: ledger:E0617, ledger:E1185</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30254" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>crank revolutions</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3B8" flags="0x30">
    <title>Starter Low-Voltage Hold - Hold Time vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter low-voltage hold: the hold ends this long after the starter engaged, by coolant temperature at start-up; after that the normal key and crank time rules apply again. Stock 4.5 s at -30 C to 1.5 s from 7.5 C. Effect: raise = the starter is held longer through a voltage collapse Evidence: ledger:E0618, ledger:E1025, ledger:E1288</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-30" />
      <LABEL index="1" value="-17.5" />
      <LABEL index="2" value="-5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="20" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3021C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3B9" flags="0x30">
    <title>Starter Low-Voltage Hold - Arm Time vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starter low-voltage hold: if system voltage collapses below 4 V while cranking, the PCM keeps the starter engaged without the key signal. That can only begin once the starter has been engaged for this long. Stock 0.2 s. Effect: raise = the starter must be engaged longer before the hold can begin Evidence: ledger:E0619, ledger:E1025, ledger:E1288</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-30" />
      <LABEL index="1" value="-17.5" />
      <LABEL index="2" value="-5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="20" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3020C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3BA" flags="0x0">
    <title>Vehicle Bus - Oil Life Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum time between two sends of the oil life message. Stock 1.0 s. Vehicle bus (serial data to the other modules): the message is sent again once at least the minimum interval has passed since it was last sent and the value has changed by at least the change threshold (or a status in it changed). Effect: lower = sent more often Evidence: ledger:E0626, ledger:E0801, ledger:E0805, ledger:E1676</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20240" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3BB" flags="0x0">
    <title>Idle Speed Control - Integral Dead Band</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: the integral term does not step while the average idle speed error is at or below this. Stock 5 rpm. Effect: raise = the controller tolerates a larger steady idle speed error Evidence: ledger:E1091</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x21FD4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3BC" flags="0x30">
    <title>Idle Speed Control Acquire - Airflow Request Floor With Throttle Sensor Fault</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: lowest total airflow request while the controller is catching the idle speed and a throttle position sensor fault is present (P0120 with P0220, or P2135), by barometric pressure (61 to 99 kPa). Stock 3.5 g/s everywhere. Effect: raise = more idle airflow in that fault mode Evidence: ledger:E1108</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>kPa baro</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="61" />
      <LABEL index="1" value="70.5" />
      <LABEL index="2" value="80" />
      <LABEL index="3" value="89.5" />
      <LABEL index="4" value="99" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22400" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3BD" flags="0x30">
    <title>Idle Speed Control Acquire - Airflow Request Floor vs Barometric Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed controller: lowest total airflow request while the controller is catching the idle speed, by barometric pressure (61 to 99 kPa). Stock -10 g/s everywhere: no floor. Effect: raise = the request cannot fall below this while catching idle Evidence: ledger:E1104</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>kPa baro</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="61" />
      <LABEL index="1" value="70.5" />
      <LABEL index="2" value="80" />
      <LABEL index="3" value="89.5" />
      <LABEL index="4" value="99" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x223F4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3BE" flags="0x30">
    <title>Idle A/C Turn-On Airflow vs Intake Air Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra idle airflow added when the A/C compressor turns on, by intake air temperature (-30 to 130 C). It is added to the A/C pressure term, held for the A/C turn-on hold time, then removed by the A/C hold airflow decay step. Stock 0 at every temperature. Effect: raise = more extra idle airflow when the A/C compressor turns on at that intake temperature Evidence: ledger:E0634, ledger:E1221</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-30" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="-10" />
      <LABEL index="3" value="0" />
      <LABEL index="4" value="10" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="40" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="60" />
      <LABEL index="10" value="70" />
      <LABEL index="11" value="80" />
      <LABEL index="12" value="90" />
      <LABEL index="13" value="100" />
      <LABEL index="14" value="110" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="130" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2243C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3BF" flags="0x30">
    <title>Idle A/C Turn-On Airflow vs A/C Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra idle airflow added when the A/C compressor turns on, by A/C refrigerant pressure (0 to 3600 kPa). It is added to the intake temperature term, held for the A/C turn-on hold time, then removed by the A/C hold airflow decay step. Stock 1.5 g/s up to 675 kPa, rising to 2.15 g/s from 1800 kPa. Effect: raise = more extra idle airflow when the A/C compressor turns on at that refrigerant pressure Evidence: ledger:E0634, ledger:E1221</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="225" />
      <LABEL index="2" value="450" />
      <LABEL index="3" value="675" />
      <LABEL index="4" value="900" />
      <LABEL index="5" value="1125" />
      <LABEL index="6" value="1350" />
      <LABEL index="7" value="1575" />
      <LABEL index="8" value="1800" />
      <LABEL index="9" value="2025" />
      <LABEL index="10" value="2250" />
      <LABEL index="11" value="2475" />
      <LABEL index="12" value="2700" />
      <LABEL index="13" value="2925" />
      <LABEL index="14" value="3150" />
      <LABEL index="15" value="3375" />
      <LABEL index="16" value="3600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22460" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3C0" flags="0x30">
    <title>Idle A/C - Settle Time vs Compressor Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: after the idle air adder has decayed, how long the A/C transient is still flagged (idle learning and the airflow integral stay blocked), by A/C compressor torque 0 to 80 Nm. Stock 0.5 s everywhere. Effect: raise = idle learning stays blocked longer after an A/C clutch change Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>Nm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29C82" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3C1" flags="0x0">
    <title>Idle Airflow Model - Correction Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter weight on the idle airflow model&#x27;s correction term: each pass the term moves this share of the way to its new estimate, then it is held between the Idle RPM-Select ceiling and floor tables. Stock 0.05 (5 percent per pass). Range 0 to 1.0. Effect: raise = the correction term follows each new estimate faster Evidence: ledger:E0643, ledger:E1202</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x220A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3C2" flags="0x30">
    <title>Engine Oil Pressure Estimate - Low Oil Pressure Input Table</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Oil pressure estimate used instead of the main estimate table while the low oil pressure input is active (coolant -40 to 152 C by engine speed 400 to 3600 rpm in five points). All zero on stock, so 0 kPa is reported while the input is active. Effect: changes the oil pressure reported while the low oil pressure input is active Evidence: ledger:E0274, ledger:E0644, ledger:E0675, ledger:E1246, ledger:E1831</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="1200" />
      <LABEL index="2" value="2000" />
      <LABEL index="3" value="2800" />
      <LABEL index="4" value="3600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2283A" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3C3" flags="0x30">
    <title>Purge O2 Feedback - Reference Flow Needed to Step Up vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: the purge factor may step up only while the purge reference flow at the present manifold vacuum is above this, by engine airflow (0 to 128 g/s). Stock 0: no restriction except at zero vacuum. Purge flow units: the full scale word (stock 123) is full purge reference flow. Effect: raise = the purge factor only rises when more manifold vacuum is available Evidence: ledger:E1122</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <LABEL index="17" value="68" />
      <LABEL index="18" value="72" />
      <LABEL index="19" value="76" />
      <LABEL index="20" value="80" />
      <LABEL index="21" value="84" />
      <LABEL index="22" value="88" />
      <LABEL index="23" value="92" />
      <LABEL index="24" value="96" />
      <LABEL index="25" value="100" />
      <LABEL index="26" value="104" />
      <LABEL index="27" value="108" />
      <LABEL index="28" value="112" />
      <LABEL index="29" value="116" />
      <LABEL index="30" value="120" />
      <LABEL index="31" value="124" />
      <LABEL index="32" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2440A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flow units</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3C4" flags="0x30">
    <title>Closed Loop Minimum MAP vs Baro</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel is not used while manifold pressure is below this, by barometric pressure (65 to 105 kPa). Stock 0 at every point: no limit. Effect: raise = closed loop is given up at light load (low MAP) Evidence: ledger:E1127</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa baro</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="65" />
      <LABEL index="1" value="70" />
      <LABEL index="2" value="75" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="85" />
      <LABEL index="5" value="90" />
      <LABEL index="6" value="95" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x250BC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3C5" flags="0x30">
    <title>Acceleration Fuel Adder - Gain vs Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra fuel on acceleration: share of each rise in the calculated fuel per cylinder that is added on top as extra fuel, by port temperature. Only used while wall film compensation is enabled. Stock 0 at every point: the adder is off and the wall film compensation does all transient fuelling. Effect: raise = more extra fuel when the fuel demand rises Evidence: ledger:E1127</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (port temp model)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-24" />
      <LABEL index="2" value="-8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="24" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="56" />
      <LABEL index="7" value="72" />
      <LABEL index="8" value="88" />
      <LABEL index="9" value="104" />
      <LABEL index="10" value="120" />
      <LABEL index="11" value="136" />
      <LABEL index="12" value="152" />
      <LABEL index="13" value="168" />
      <LABEL index="14" value="184" />
      <LABEL index="15" value="200" />
      <LABEL index="16" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26646" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3C6" flags="0x30">
    <title>PE Enable Throttle - Adder vs Baro</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the power enrichment (PE) enable throttle threshold (PE enable throttle vs RPM) by barometric pressure. Stock 0 at every baro. Effect: raise = more throttle is needed before PE enables at that barometric pressure Evidence: ledger:E0644, ledger:E1397</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="65" />
      <LABEL index="1" value="70" />
      <LABEL index="2" value="75" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="85" />
      <LABEL index="5" value="90" />
      <LABEL index="6" value="95" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x295E0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3C7" flags="0x30">
    <title>Idle Airflow RPM Adder - Reduction vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: airflow taken off the rpm airflow adder, by engine speed (400 to 3600 rpm). Stock 0 everywhere. Effect: raise = less feed-forward airflow at that engine speed Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29E18" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3C8" flags="0x30">
    <title>Idle Airflow - Correction Term vs Converter Slip</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added by filtered torque converter slip (-256 to +256 rpm), at road speed with the throttle closed, outside decel fuel cut, once the idle airflow error has settled. Stock 0 at every slip. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (raise = more idle airflow at that converter slip) Evidence: ledger:E0644, ledger:E0897, ledger:E0936, ledger:E1280</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm (converter slip, filtered)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-256" />
      <LABEL index="1" value="-240" />
      <LABEL index="2" value="-224" />
      <LABEL index="3" value="-208" />
      <LABEL index="4" value="-192" />
      <LABEL index="5" value="-176" />
      <LABEL index="6" value="-160" />
      <LABEL index="7" value="-144" />
      <LABEL index="8" value="-128" />
      <LABEL index="9" value="-112" />
      <LABEL index="10" value="-96" />
      <LABEL index="11" value="-80" />
      <LABEL index="12" value="-64" />
      <LABEL index="13" value="-48" />
      <LABEL index="14" value="-32" />
      <LABEL index="15" value="-16" />
      <LABEL index="16" value="0" />
      <LABEL index="17" value="16" />
      <LABEL index="18" value="32" />
      <LABEL index="19" value="48" />
      <LABEL index="20" value="64" />
      <LABEL index="21" value="80" />
      <LABEL index="22" value="96" />
      <LABEL index="23" value="112" />
      <LABEL index="24" value="128" />
      <LABEL index="25" value="144" />
      <LABEL index="26" value="160" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="192" />
      <LABEL index="29" value="208" />
      <LABEL index="30" value="224" />
      <LABEL index="31" value="240" />
      <LABEL index="32" value="256" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29E52" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3C9" flags="0x30">
    <title>Idle RPM Event - Drop per Update Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. An idle speed drop larger than this in one 12.5 ms update starts a drop event, by desired idle (400 to 1200 rpm). Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0644, ledger:E1505</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="450" />
      <LABEL index="2" value="500" />
      <LABEL index="3" value="550" />
      <LABEL index="4" value="600" />
      <LABEL index="5" value="650" />
      <LABEL index="6" value="700" />
      <LABEL index="7" value="750" />
      <LABEL index="8" value="800" />
      <LABEL index="9" value="850" />
      <LABEL index="10" value="900" />
      <LABEL index="11" value="950" />
      <LABEL index="12" value="1000" />
      <LABEL index="13" value="1050" />
      <LABEL index="14" value="1100" />
      <LABEL index="15" value="1150" />
      <LABEL index="16" value="1200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AB40" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3CA" flags="0x30">
    <title>Idle RPM Event - Rise per Update Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. An idle speed rise larger than this in one 12.5 ms update starts a rise event, by desired idle (400 to 1200 rpm). Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0644, ledger:E1505</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="450" />
      <LABEL index="2" value="500" />
      <LABEL index="3" value="550" />
      <LABEL index="4" value="600" />
      <LABEL index="5" value="650" />
      <LABEL index="6" value="700" />
      <LABEL index="7" value="750" />
      <LABEL index="8" value="800" />
      <LABEL index="9" value="850" />
      <LABEL index="10" value="900" />
      <LABEL index="11" value="950" />
      <LABEL index="12" value="1000" />
      <LABEL index="13" value="1050" />
      <LABEL index="14" value="1100" />
      <LABEL index="15" value="1150" />
      <LABEL index="16" value="1200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AB64" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3CB" flags="0x30">
    <title>Idle Load State - Park/Neutral Delay vs Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle tables, Park / Neutral or in gear rows: delay after a shift to Park / Neutral before the Park / Neutral rows of all idle tables are used, by transmission fluid temperature (-40 to 152 C). Stock 0 everywhere: they are used on the next pass. Effect: raise = the in gear rows stay in use longer after a shift to Park / Neutral Evidence: ledger:E1113</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B266" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3CC" flags="0x30">
    <title>Misfire - Pause Floor vs Coolant (no effect at stock)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: every update the misfire pause count, in engine cycles, is raised to at least this value for the current coolant temperature, so a non-zero value keeps misfire detection paused at that temperature. Works like the general misfire pause. Stock 0 at every temperature, so it has no effect on the stock calibration. Raising it stops misfire detection at those temperatures. Effect: raise = misfire detection held off at that coolant temperature Evidence: ledger:E0772, ledger:E1878</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-10" />
      <LABEL index="1" value="-4" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="14" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="26" />
      <LABEL index="7" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39688" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>cycles</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3CD" flags="0x30">
    <title>Cruise Control - Cancel Speed Drop Below Target vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: an active cruise is cancelled when vehicle speed falls this far below the cruise target speed (negative = below the target). Looked up by vehicle speed (38 to 180 km/h). Stock -15 km/h at 38 km/h, -34 km/h at 80 km/h, -39 km/h from 127 km/h up. Effect: more negative = the cruise stays on through a bigger speed drop Evidence: ledger:E0646, ledger:E0730, ledger:E0839, ledger:E1256</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.875" />
      <LABEL index="2" value="55.75" />
      <LABEL index="3" value="64.625" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.375" />
      <LABEL index="6" value="91.25" />
      <LABEL index="7" value="100.125" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.875" />
      <LABEL index="10" value="126.75" />
      <LABEL index="11" value="135.625" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.375" />
      <LABEL index="14" value="162.25" />
      <LABEL index="15" value="171.125" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x219AC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3CE" flags="0x30">
    <title>Cruise Control - Cancel at Deceleration vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control cancels when the vehicle slows down faster than this (filtered change of vehicle speed, negative = slowing), by vehicle speed. Stock -40 km/h per second at every speed, far beyond normal braking, so in practice this catches a speed signal that drops out. Effect: closer to 0 = cruise cancels on gentler deceleration Evidence: ledger:E0647, ledger:E0730, ledger:E0839, ledger:E1164, ledger:E1167</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.875" />
      <LABEL index="2" value="55.75" />
      <LABEL index="3" value="64.625" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.375" />
      <LABEL index="6" value="91.25" />
      <LABEL index="7" value="100.125" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.875" />
      <LABEL index="10" value="126.75" />
      <LABEL index="11" value="135.625" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.375" />
      <LABEL index="14" value="162.25" />
      <LABEL index="15" value="171.125" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x219D0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per s</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3CF" flags="0x30">
    <title>Cruise Control - Cancel at Acceleration vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control cancels when the vehicle gains speed faster than this (filtered change of vehicle speed), by vehicle speed. Stock +16 km/h per second at every speed, which normal driving does not reach, so in practice this catches wheel spin or a jumping speed signal. Effect: lower = cruise cancels on gentler acceleration Evidence: ledger:E0647, ledger:E0730, ledger:E0839, ledger:E1164, ledger:E1167</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.875" />
      <LABEL index="2" value="55.75" />
      <LABEL index="3" value="64.625" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.375" />
      <LABEL index="6" value="91.25" />
      <LABEL index="7" value="100.125" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.875" />
      <LABEL index="10" value="126.75" />
      <LABEL index="11" value="135.625" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.375" />
      <LABEL index="14" value="162.25" />
      <LABEL index="15" value="171.125" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x219F4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per s</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3D0" flags="0x0">
    <title>Idle Sequencer - State 1 Advance Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed sequencer: time spent in state 1 before it may advance to state 2. Stock 0 s (advances at once). Effect: raise = the sequencer stays longer in state 1 Evidence: ledger:E0648, ledger:E1265</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A218" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>-204.800000</min>
    <max>204.793750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3D1" flags="0x0">
    <title>Idle Sequencer - Rpm Over Desired Hold Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed sequencer: time engine speed must stay above the desired idle speed by more than the allowed margin before the sequencer advances from state 1 to state 2. Stock 0 s. Effect: raise = rpm must stay high longer before the sequencer moves on Evidence: ledger:E0649, ledger:E1265</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A21C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>-204.800000</min>
    <max>204.793750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3D2" flags="0x0">
    <title>Idle Disturbance Latch - Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: the disturbance latch can set only above this vehicle speed. Stock 512 km/h: off. The disturbance latch: in closed loop idle speed control with the throttle closed, a sudden rpm change above a speed threshold puts the idle controller back in its moving mode for a time. Effect: lower = the latch can set at lower speed Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A228" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3D3" flags="0x0">
    <title>First-Run Mode - Post-Start Airflow Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First-run mode runs only during the first 12 s of engine running recorded by the PCM. During it the post-start airflow is applied whatever the post-start time limit and is multiplied by this. Stock 5.0. Effect: raise = more post-start airflow during first-run mode Evidence: ledger:E0652, ledger:E1232</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2A234" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>2</decimalpl>
    <min>-16.000000</min>
    <max>15.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3D4" flags="0x30">
    <title>Fuel Level vs Sender Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converts the fuel tank level sender voltage (0 to 5 V in 0.156 V steps) to the fuel level the PCM reports on the fuel level PID and uses for its EVAP leak tests. Cells are fuel level in %. Stock reads full (101 %) up to about 0.8 V and falls to empty at about 2.7 V. Change it only to match a different sender. Effect: raise = the PCM reads a fuller tank at that sender voltage Evidence: ledger:E0655, ledger:E0936, ledger:E0955</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>V (fuel level sender)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.156" />
      <LABEL index="2" value="0.312" />
      <LABEL index="3" value="0.469" />
      <LABEL index="4" value="0.625" />
      <LABEL index="5" value="0.781" />
      <LABEL index="6" value="0.938" />
      <LABEL index="7" value="1.094" />
      <LABEL index="8" value="1.25" />
      <LABEL index="9" value="1.406" />
      <LABEL index="10" value="1.562" />
      <LABEL index="11" value="1.719" />
      <LABEL index="12" value="1.875" />
      <LABEL index="13" value="2.031" />
      <LABEL index="14" value="2.188" />
      <LABEL index="15" value="2.344" />
      <LABEL index="16" value="2.5" />
      <LABEL index="17" value="2.656" />
      <LABEL index="18" value="2.812" />
      <LABEL index="19" value="2.969" />
      <LABEL index="20" value="3.125" />
      <LABEL index="21" value="3.281" />
      <LABEL index="22" value="3.438" />
      <LABEL index="23" value="3.594" />
      <LABEL index="24" value="3.75" />
      <LABEL index="25" value="3.906" />
      <LABEL index="26" value="4.062" />
      <LABEL index="27" value="4.219" />
      <LABEL index="28" value="4.375" />
      <LABEL index="29" value="4.531" />
      <LABEL index="30" value="4.688" />
      <LABEL index="31" value="4.844" />
      <LABEL index="32" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37F2A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% fuel level</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>292.763011</max>
      <MATH equation="X/223.85"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3D5" flags="0x30">
    <title>PE Delay Countdown Rate vs Throttle x RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How much power-enrichment (PE) delay time is removed each update while PE is requested, by throttle and rpm. The PE delay store fills up to PE Delay - Maximum Delay Store while PE is not requested and must drain before a delayed PE request takes effect. Stock 0.05 s per update at low throttle and rpm, rising to 0.35 to 0.5 s at high throttle and high rpm. Effect: raise = the power-enrichment (PE) delay timer counts down faster at that throttle/rpm cell, shortening the PE delay Evidence: ledger:E0654, ledger:E0704, ledger:E1329, ledger:E1337</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% (throttle)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29610" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s per update</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3D6" flags="0x30">
    <title>A/C Refrigerant Pressure Sensor Transfer</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converts the A/C refrigerant pressure sensor voltage (0 to 4.95 V) to pressure. The result is the pressure used by the A/C compressor cut-outs and the A/C idle airflow. Stock 0 kPa at 0 V rising about 227 kPa per 0.31 V to 3446 kPa at 4.95 V. Effect: raise = a higher pressure reading for the same sensor voltage Evidence: ledger:E0662, ledger:E0937, ledger:E1223</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>V</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.309" />
      <LABEL index="2" value="0.619" />
      <LABEL index="3" value="0.928" />
      <LABEL index="4" value="1.238" />
      <LABEL index="5" value="1.547" />
      <LABEL index="6" value="1.856" />
      <LABEL index="7" value="2.166" />
      <LABEL index="8" value="2.475" />
      <LABEL index="9" value="2.785" />
      <LABEL index="10" value="3.094" />
      <LABEL index="11" value="3.403" />
      <LABEL index="12" value="3.713" />
      <LABEL index="13" value="4.022" />
      <LABEL index="14" value="4.332" />
      <LABEL index="15" value="4.641" />
      <LABEL index="16" value="4.95" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x200B2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3D7" flags="0x0">
    <title>P1545 Circuit Check - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Output circuit check P1545 only runs with engine speed at or above this. Stock 425 rpm. Effect: raise = the check needs a higher engine speed Evidence: ledger:E1058</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34574" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3D8" flags="0x0">
    <title>Traction Control - Minimum Engine Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control torque reduction: it is allowed only after the engine has run longer than this. Stock 2 s. Effect: raise = no torque reduction until later after the start Evidence: ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30290" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3D9" flags="0x0">
    <title>Traction Control - Torque Signal Full Scale</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control: engine torque that the top of the signal range stands for, on both the torque request coming from the brake module and the delivered torque signal going back to it. It is also the request used while the signal is invalid (no limit). It has to match the brake module. Stock 350 Nm. Effect: changing it rescales the incoming torque request and the outgoing delivered torque together Evidence: ledger:E0666, ledger:E0918, ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30276" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>16383.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3DA" flags="0x30">
    <title>Traction Control - Torque Request Floor vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The traction control sends the engine a torque limit; while traction control is active it becomes the electronic throttle torque limit. The request is never lower than this value at the current engine speed. Stock 30 Nm at 0 and 512 rpm, 0 from 1024 rpm. Effect: raise = traction control cannot pull torque below this at that rpm Evidence: ledger:E0667, ledger:E0918</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30FD0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>Nm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x3DB" flags="0x0">
    <title>Traction Control - Minimum Engine Speed, Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control torque reduction: once allowed, it stays allowed until engine speed falls to this. Stock 500 rpm. Effect: raise = torque reduction is dropped at a higher engine speed Evidence: ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3028E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x3DC" flags="0x0">
    <title>Traction Control - Minimum Engine Speed, On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control torque reduction: it is allowed once engine speed is above this. Stock 600 rpm. Effect: raise = no torque reduction until a higher engine speed Evidence: ledger:E1114</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3028C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x3DD" flags="0x30">
    <title>Purge Flow - Maximum Request vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge: highest purge flow request at each engine airflow (0 to 128 g/s), before the purge factors scale it down. Stock 0 at no airflow rising to 123 from 24 g/s. Purge flow units: the full scale word (stock 123) is full purge reference flow. Effect: raise = more purge at that engine airflow Evidence: ledger:E1122</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <LABEL index="17" value="68" />
      <LABEL index="18" value="72" />
      <LABEL index="19" value="76" />
      <LABEL index="20" value="80" />
      <LABEL index="21" value="84" />
      <LABEL index="22" value="88" />
      <LABEL index="23" value="92" />
      <LABEL index="24" value="96" />
      <LABEL index="25" value="100" />
      <LABEL index="26" value="104" />
      <LABEL index="27" value="108" />
      <LABEL index="28" value="112" />
      <LABEL index="29" value="116" />
      <LABEL index="30" value="120" />
      <LABEL index="31" value="124" />
      <LABEL index="32" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x244CA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flow units</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3DE" flags="0x30">
    <title>Purge Learned Memory Weight vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: how much of the purge learned memory correction is applied, by airflow (0 to 128 g/s). Stock: all of it up to 32 g/s, falling to one tenth from 104 g/s. Effect: raise = more of the purge correction is applied at that airflow Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <LABEL index="17" value="68" />
      <LABEL index="18" value="72" />
      <LABEL index="19" value="76" />
      <LABEL index="20" value="80" />
      <LABEL index="21" value="84" />
      <LABEL index="22" value="88" />
      <LABEL index="23" value="92" />
      <LABEL index="24" value="96" />
      <LABEL index="25" value="100" />
      <LABEL index="26" value="104" />
      <LABEL index="27" value="108" />
      <LABEL index="28" value="112" />
      <LABEL index="29" value="116" />
      <LABEL index="30" value="120" />
      <LABEL index="31" value="124" />
      <LABEL index="32" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24B9A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3DF" flags="0x30">
    <title>Port Temperature Model Target - Air-Fuel Ratio Offset vs AFR</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. By commanded air-fuel ratio: the model&#x27;s air-fuel ratio terms use the average of the commanded air-fuel ratio and this value. Stock 12.0 at 0 AFR falling to 1.0 at 19.2 AFR, 0 from 20 AFR. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = the air-fuel ratio terms see a leaner effective ratio...</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>AFR (commanded)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.8" />
      <LABEL index="2" value="1.6" />
      <LABEL index="3" value="2.4" />
      <LABEL index="4" value="3.2" />
      <LABEL index="5" value="4" />
      <LABEL index="6" value="4.8" />
      <LABEL index="7" value="5.6" />
      <LABEL index="8" value="6.4" />
      <LABEL index="9" value="7.2" />
      <LABEL index="10" value="8" />
      <LABEL index="11" value="8.8" />
      <LABEL index="12" value="9.6" />
      <LABEL index="13" value="10.4" />
      <LABEL index="14" value="11.2" />
      <LABEL index="15" value="12" />
      <LABEL index="16" value="12.8" />
      <LABEL index="17" value="13.6" />
      <LABEL index="18" value="14.4" />
      <LABEL index="19" value="15.2" />
      <LABEL index="20" value="16" />
      <LABEL index="21" value="16.8" />
      <LABEL index="22" value="17.6" />
      <LABEL index="23" value="18.4" />
      <LABEL index="24" value="19.2" />
      <LABEL index="25" value="20" />
      <LABEL index="26" value="20.8" />
      <LABEL index="27" value="21.6" />
      <LABEL index="28" value="22.4" />
      <LABEL index="29" value="23.2" />
      <LABEL index="30" value="24" />
      <LABEL index="31" value="24.8" />
      <LABEL index="32" value="25.6" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B5F2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>AFR</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>31.999512</max>
      <MATH equation="X/2048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E0" flags="0x30">
    <title>Port Temperature Model - Response Rate vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the modelled intake port temperature (used by the transient wall-wetting fuel) moves toward its target each update, by airflow. Stock 0.8 % of the gap at no airflow rising to 8 % from about 210 g/s. Effect: raise = the port temperature model follows its target faster Evidence: ledger:E0741</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <LABEL index="9" value="144" />
      <LABEL index="10" value="160" />
      <LABEL index="11" value="176" />
      <LABEL index="12" value="192" />
      <LABEL index="13" value="208" />
      <LABEL index="14" value="224" />
      <LABEL index="15" value="240" />
      <LABEL index="16" value="256" />
      <LABEL index="17" value="272" />
      <LABEL index="18" value="288" />
      <LABEL index="19" value="304" />
      <LABEL index="20" value="320" />
      <LABEL index="21" value="336" />
      <LABEL index="22" value="352" />
      <LABEL index="23" value="368" />
      <LABEL index="24" value="384" />
      <LABEL index="25" value="400" />
      <LABEL index="26" value="416" />
      <LABEL index="27" value="432" />
      <LABEL index="28" value="448" />
      <LABEL index="29" value="464" />
      <LABEL index="30" value="480" />
      <LABEL index="31" value="496" />
      <LABEL index="32" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B63A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E1" flags="0x30">
    <title>Charge Temperature Conversion (C to K)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converts the blended intake and coolant temperature into the absolute charge temperature used by the cranking airmass calculation (ideal gas law). Stock is an exact Celsius to Kelvin conversion, 233 K at -40 C to 413 K at 140 C. Effect: raise = less cranking airmass (leaner cranking fuel) at that temperature; stock is exact physics Evidence: ledger:E0772, ledger:E0803, ledger:E0861</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>19</indexcount>
      <units>degC (intake / coolant blend)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <LABEL index="17" value="130" />
      <LABEL index="18" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2BD6E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="19" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>K</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E2" flags="0x30">
    <title>Corrected Coolant Model - Start Delay vs Start-Up Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine revolutions after start during which the corrected coolant temperature stays at its start value, by coolant temperature at start. After this the warm-up rate curve raises it. Stock 3513 revolutions at -40 C, 1200 at 7.5 C, 100 from about 79 C. Effect: raise = the modelled coolant temperature stays at its start value for more engine revolutions Evidence: ledger:E0254, ledger:E0769, ledger:E1185</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28.125" />
      <LABEL index="2" value="-16.25" />
      <LABEL index="3" value="-4.375" />
      <LABEL index="4" value="7.5" />
      <LABEL index="5" value="19.375" />
      <LABEL index="6" value="31.25" />
      <LABEL index="7" value="43.125" />
      <LABEL index="8" value="55" />
      <LABEL index="9" value="66.875" />
      <LABEL index="10" value="78.75" />
      <LABEL index="11" value="90.625" />
      <LABEL index="12" value="102.5" />
      <LABEL index="13" value="114.375" />
      <LABEL index="14" value="126.25" />
      <LABEL index="15" value="138.125" />
      <LABEL index="16" value="150" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22C12" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>crank revolutions</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E3" flags="0x30">
    <title>Corrected Coolant Model - Warm-Up Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the corrected coolant temperature rises after the start delay, in degrees per 1000 engine revolutions, by the modelled temperature itself. Stock 5.5 C per 1000 revolutions when cold, falling to 3.1 from about 100 C. Effect: raise = the modelled coolant temperature rises faster after the start delay Evidence: ledger:E0254, ledger:E0769, ledger:E1185</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28.125" />
      <LABEL index="2" value="-16.25" />
      <LABEL index="3" value="-4.375" />
      <LABEL index="4" value="7.5" />
      <LABEL index="5" value="19.375" />
      <LABEL index="6" value="31.25" />
      <LABEL index="7" value="43.125" />
      <LABEL index="8" value="55" />
      <LABEL index="9" value="66.875" />
      <LABEL index="10" value="78.75" />
      <LABEL index="11" value="90.625" />
      <LABEL index="12" value="102.5" />
      <LABEL index="13" value="114.375" />
      <LABEL index="14" value="126.25" />
      <LABEL index="15" value="138.125" />
      <LABEL index="16" value="150" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22C36" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC per 1000 revolutions</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>999.984741</max>
      <MATH equation="X/65.536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E4" flags="0x30">
    <title>Crank Signal Filter - Minimum Time Between Teeth vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crank sensor noise filter: a crank tooth edge that arrives sooner than this after the previous accepted edge is ignored, by engine speed. Values of 30 us and below leave the timer check at its last setting and go to a separate input filter setting instead. Stock 391 us at 0 rpm, 195 us at 512 rpm, about a tenth of a tooth period, 16 us from 5632 rpm. Effect: raise = more noise rejected, but real teeth closer together than this would be missed Evidence: ledger:E0781, ledger:E1273, ledger:E1638</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22D26" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>us</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E5" flags="0x30">
    <title>Reduced Engine Power - Throttle Area Limit vs Speed (Hard Acceleration)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While a throttle control fault is active (reduced engine power), the throttle opening is limited to this share of full throttle area, by vehicle speed, whenever the vehicle accelerates harder than its allowed rate; a term that grows with the extra acceleration is taken off the limit. Applies above 8 km/h. Stock 2.0 % at 0 km/h rising to 34.0 % at 80 km/h. Effect: raise = more throttle allowed under reduced engine power when the vehicle accelerates hard Evidence: ledger:E0781, ledger:E1866</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23052" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E6" flags="0x30">
    <title>Pedal Position - Rise Hysteresis vs Pedal</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal: amount the pedal must rise above the last value before the pedal position follows it, by pedal position (0 to 100 %). A falling pedal is followed at once. Stock 0.5 % (0 at the two ends). Effect: raise = small pedal movements upward are ignored Evidence: ledger:E1120</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% pedal</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24154" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E7" flags="0x30">
    <title>EVAP Purge - Minimum Target vs System Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest EVAP purge target allowed at each system voltage, applied unless an EVAP test is running. Stock 0 up to 6 V, 23 % at 7.5 V, 11 % from 12 V up. Effect: raise = more purge at that system voltage Evidence: ledger:E0746</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>V</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1.5" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4.5" />
      <LABEL index="4" value="6" />
      <LABEL index="5" value="7.5" />
      <LABEL index="6" value="9" />
      <LABEL index="7" value="10.5" />
      <LABEL index="8" value="12" />
      <LABEL index="9" value="13.5" />
      <LABEL index="10" value="15" />
      <LABEL index="11" value="16.5" />
      <LABEL index="12" value="18" />
      <LABEL index="13" value="19.5" />
      <LABEL index="14" value="21" />
      <LABEL index="15" value="22.5" />
      <LABEL index="16" value="24" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24386" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.781250</max>
      <MATH equation="X/326.4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E8" flags="0x30">
    <title>Purge O2 Feedback - Factor Maximum vs Intake Air Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: highest value of the purge factor, by intake air temperature (-40 to 152 C). Stock 0.8 cold, 1.0 from 8 to 68 C, falling to 0.25 at 152 C. Effect: raise = more purge is allowed at that intake air temperature Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC intake air</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x243C0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3E9" flags="0x30">
    <title>Purge O2 Feedback - Rich Time Before Fast Step vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: time the mixture must stay rich before the fast step and period are used, by engine airflow (0 to 128 g/s). Stock 0.6 s up to 32 g/s, 0.4 s above. Effect: raise = the fast cut back starts later Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>g/s airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="8" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="24" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="48" />
      <LABEL index="7" value="56" />
      <LABEL index="8" value="64" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="88" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="104" />
      <LABEL index="14" value="112" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x243E4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3EA" flags="0x30">
    <title>Purge Amount - Factor Cap vs Fuel Tank Vacuum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount: after the EVAP leak test has finished for the trip, the purge factor is limited to this when fuel tank vacuum stays high for the tank vacuum cap time, by tank vacuum (-32 to +32 inH2O, positive = vacuum). Stock 1.0 up to 8 inH2O, 0.5 at 12 inH2O and 0 from 16 inH2O: purge stops before it pulls the tank down further. Effect: raise = more purge is allowed at that tank vacuum Evidence: ledger:E1123</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>inH2O tank vacuum</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-32" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-20" />
      <LABEL index="4" value="-16" />
      <LABEL index="5" value="-12" />
      <LABEL index="6" value="-8" />
      <LABEL index="7" value="-4" />
      <LABEL index="8" value="0" />
      <LABEL index="9" value="4" />
      <LABEL index="10" value="8" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="16" />
      <LABEL index="13" value="20" />
      <LABEL index="14" value="24" />
      <LABEL index="15" value="28" />
      <LABEL index="16" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x244A6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3EB" flags="0x30">
    <title>Crank to Run Fuel Blend Rate vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the engine starts, the base fuel amount moves from the cranking fuel amount (the one shaped by Base Fuel Multiplier vs RPM) to the normal running amount. This is the fraction of that change made each update, by coolant temperature; the move is complete when the total reaches 1.0. Stock 0.05 up to 2 C, 0.07 at 14 C and 0.10 from 26 C. Effect: raise = fueling reaches the normal running amount sooner after a start Evidence: ledger:E0670, ledger:E0969</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x26E1C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x249E4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3EC" flags="0x30">
    <title>Acceleration Fuel Adder - Decay vs Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra fuel on acceleration: share of the adder that is kept at each update (each injection event of the cylinder), by port temperature. Stock 0.73 cold, 0.30 hot. No effect while the adder gain is 0, as on the stock calibration. Effect: raise = the extra fuel fades out more slowly Evidence: ledger:E1127</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (port temp model)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-24" />
      <LABEL index="2" value="-8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="24" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="56" />
      <LABEL index="7" value="72" />
      <LABEL index="8" value="88" />
      <LABEL index="9" value="104" />
      <LABEL index="10" value="120" />
      <LABEL index="11" value="136" />
      <LABEL index="12" value="152" />
      <LABEL index="13" value="168" />
      <LABEL index="14" value="184" />
      <LABEL index="15" value="200" />
      <LABEL index="16" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26622" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3ED" flags="0x30">
    <title>Transient Fuel Model Temperature vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest temperature the transient fuel (wall wetting) model uses, by coolant temperature (-40 to 152 C). The model takes the higher of this and the coolant based temperature. Stock equal to coolant up to 80 C, then 120 C at 92 C rising to 155 C from 128 C. Effect: raise = the transient fuel model treats the ports as hotter at that coolant temperature Evidence: ledger:E0670, ledger:E0937, ledger:E1224</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B67E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3EE" flags="0x30">
    <title>Transient Fuel Model - Hot Restart Temperature Carry-Over</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the transient (wall-wetting) fuel model starts, its temperature starts between the current coolant temperature and the hotter temperature it had when the engine was shut off. This is the fraction of that difference kept, by engine-off time (0 to 512 s). Stock 1.0 right after shut-off, 0.5 at 32 s, 0.25 at 96 s and 0 from 256 s. Effect: raise = a hot restart is treated as hotter for longer Evidence: ledger:E0670, ledger:E0965</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>s (engine-off time)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="32" />
      <LABEL index="2" value="64" />
      <LABEL index="3" value="96" />
      <LABEL index="4" value="128" />
      <LABEL index="5" value="160" />
      <LABEL index="6" value="192" />
      <LABEL index="7" value="224" />
      <LABEL index="8" value="256" />
      <LABEL index="9" value="288" />
      <LABEL index="10" value="320" />
      <LABEL index="11" value="352" />
      <LABEL index="12" value="384" />
      <LABEL index="13" value="416" />
      <LABEL index="14" value="448" />
      <LABEL index="15" value="480" />
      <LABEL index="16" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B6A2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3EF" flags="0x30">
    <title>EVAP Engine-Off Test - Vent Open Time vs Ambient Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: how long the vent stays open at the start of the test before the pressure phase begins, by ambient air temperature. Stock 30 s when cold rising to 500 s when hot. Effect: raise = the tank is vented longer before the test starts measuring Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (ambient air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-10" />
      <LABEL index="1" value="-4.375" />
      <LABEL index="2" value="1.25" />
      <LABEL index="3" value="6.875" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.125" />
      <LABEL index="6" value="23.75" />
      <LABEL index="7" value="29.375" />
      <LABEL index="8" value="35" />
      <LABEL index="9" value="40.625" />
      <LABEL index="10" value="46.25" />
      <LABEL index="11" value="51.875" />
      <LABEL index="12" value="57.5" />
      <LABEL index="13" value="63.125" />
      <LABEL index="14" value="68.75" />
      <LABEL index="15" value="74.375" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35A36" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3F0" flags="0x30">
    <title>EVAP Engine-Off Test - Vent Open Time vs Ambient Temperature (service test)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: the same vent-open time for the scan tool started version of the test while its ambient temperature estimate is not yet valid. Stock equal to the normal curve. Effect: raise = the tank is vented longer before the service test starts measuring Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (ambient air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-10" />
      <LABEL index="1" value="-4.375" />
      <LABEL index="2" value="1.25" />
      <LABEL index="3" value="6.875" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.125" />
      <LABEL index="6" value="23.75" />
      <LABEL index="7" value="29.375" />
      <LABEL index="8" value="35" />
      <LABEL index="9" value="40.625" />
      <LABEL index="10" value="46.25" />
      <LABEL index="11" value="51.875" />
      <LABEL index="12" value="57.5" />
      <LABEL index="13" value="63.125" />
      <LABEL index="14" value="68.75" />
      <LABEL index="15" value="74.375" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35A5A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3F1" flags="0x30">
    <title>Fuel Trim Monitor - Purge Ramp Up Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim monitor purge-off test (P0172): amount commanded purge is raised every 100 ms when purge is restored after the measurement, by the normal purge command (0 to 100 %). Stock 0.5 % per step up to 25 % purge, 5 % at 31 %, 10 % above. Effect: raise = purge returns faster after the test Evidence: ledger:E0670, ledger:E1068</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% commanded purge</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.275" />
      <LABEL index="2" value="12.55" />
      <LABEL index="3" value="18.825" />
      <LABEL index="4" value="25.1" />
      <LABEL index="5" value="31.375" />
      <LABEL index="6" value="37.65" />
      <LABEL index="7" value="43.925" />
      <LABEL index="8" value="50.2" />
      <LABEL index="9" value="56.475" />
      <LABEL index="10" value="62.75" />
      <LABEL index="11" value="69.025" />
      <LABEL index="12" value="75.3" />
      <LABEL index="13" value="81.575" />
      <LABEL index="14" value="87.85" />
      <LABEL index="15" value="94.125" />
      <LABEL index="16" value="100.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37EB2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% per step</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.781250</max>
      <MATH equation="X/326.4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3F2" flags="0x30">
    <title>Airflow-Weighted Intake Temperature Blend Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 16-point curve indexed by airflow. Each cell is a fraction, from 0 to 1.0, that blends the intake air temperature reading toward coolant temperature: 0 keeps the raw intake reading, 1.0 uses coolant temperature entirely. This compensates for heat soak, when the intake air sensor reads artificially hot right after a hot engine is shut off and restarted with little airflow to clear it. The blended temperature feeds an air density correction inside the engine&#x27;s airflow estimate. Stock blend fraction ranges from about 0.20 to 0.71 across the airflow range, leaning further toward coolant temperature at low airflow. Effect: ra...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>16</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2BD4C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction (Q15: 32768 = weight of 1.0)</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3F3" flags="0x30">
    <title>Engine Start Detection RPM vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM decides the engine has started (cranking is over and it is running) once engine speed has stayed at or above this for the number of updates in Engine Start Detection Count, by coolant temperature. Stock 575 rpm up to about 8 C, 550 rpm from about 31 C. Effect: raise = the engine must spin faster before it counts as started Evidence: ledger:E0768, ledger:E0966</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16.25" />
      <LABEL index="2" value="7.5" />
      <LABEL index="3" value="31.25" />
      <LABEL index="4" value="55" />
      <LABEL index="5" value="78.75" />
      <LABEL index="6" value="102.5" />
      <LABEL index="7" value="126.25" />
      <LABEL index="8" value="150" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22CC4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3F4" flags="0x30">
    <title>Engine Start Detection Count vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How many updates in a row engine speed must stay at or above Engine Start Detection RPM before the PCM decides the engine has started, by coolant temperature. Stock 8 at -40 C, 6 at -16 C, 4 from about 8 C. Effect: raise = the engine must hold start speed longer Evidence: ledger:E0768, ledger:E0966</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16.25" />
      <LABEL index="2" value="7.5" />
      <LABEL index="3" value="31.25" />
      <LABEL index="4" value="55" />
      <LABEL index="5" value="78.75" />
      <LABEL index="6" value="102.5" />
      <LABEL index="7" value="126.25" />
      <LABEL index="8" value="150" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22CD8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>updates</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3F5" flags="0x30">
    <title>A/C Idle Air - Second Stage Delay vs A/C Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the staged A/C idle air sequence, after the first step of extra idle air has ramped in, the PCM waits this many engine reference periods (one period is the time between two cylinder firings, so the wait gets shorter as rpm rises) before the second stage starts; the A/C clutch is held off until the sequence ends. By A/C compressor torque (0 to 80 Nm). Stock 5 periods at 0 Nm rising to 25 periods at 80 Nm. Effect: raise = longer wait between the two stages of A/C idle air before the A/C engages Evidence: ledger:E0670, ledger:E1870</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>Nm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A96C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>reference periods</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3F6" flags="0x30">
    <title>Idle Airflow - Shortfall Add-On vs Airflow Shortfall</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra idle airflow added when measured airflow falls short of the predicted idle airflow, by the size of the shortfall (0 to 4 g/s). The detector that would use it cannot arm on this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0289, ledger:E0670, ledger:E0936, ledger:E1187</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s (predicted minus measured airflow)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.5" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="1.5" />
      <LABEL index="4" value="2" />
      <LABEL index="5" value="2.5" />
      <LABEL index="6" value="3" />
      <LABEL index="7" value="3.5" />
      <LABEL index="8" value="4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B2DE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3F7" flags="0x30">
    <title>Idle Airflow - Shortfall Add-On, Second Term (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Second term added to the idle airflow shortfall add-on. The software feeds this table a fixed zero input, so only its first point is ever used, and that point is 0 on stock (the remaining points, 0.125 to 1.0 g/s, are never reached). Dormant: no effect on this truck&#x27;s software. Effect: raising the first point adds that airflow whenever the shortfall add-on runs; the other points are never used Evidence: ledger:E0670, ledger:E0936, ledger:E1187, ledger:E1241</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B2F2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3F8" flags="0x30">
    <title>Burst Knock Retard - Multiplier vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant factor on the burst knock retard, alongside its intake temperature and rpm multipliers (1.0 = full retard). Lower = less burst knock retard at that coolant temperature. Effect: raise = more burst knock retard at that coolant Evidence: ledger:E0759</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B8DA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3F9" flags="0x30">
    <title>Burst Knock Retard Multiplier vs Coolant, Per-Bank</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A curve, indexed by coolant temperature from -40 to 152 degrees Celsius over 9 points, that scales how much a per-bank rolling maximum burst-knock-retard value is updated each pass. Stock ranges from a multiplier of 0.20 at the coldest point to about 1.00 once the engine is warm. Effect: Raising a point increases how much the coolant-based multiplier contributes when updating that bank&#x27;s rolling burst-knock-retard maximum at that temperature; lowering it reduces that contribution. Evidence: ledger:E0772, ledger:E0805</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B91A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain (Q16, unitless)</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3FA" flags="0x30">
    <title>Knock Learn Rate - Coolant Curve</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is the coolant temperature curve. Effect: raise = faster knock learning for under-sampled cylinders there Evidence: ledger:E0193, ledger:E0772, ledger:E0871</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2BA82" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3FB" flags="0x30">
    <title>Knock Learn Rate - Intake Temperature Curve</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is the intake temperature curve. Effect: raise = faster knock learning for under-sampled cylinders there Evidence: ledger:E0193, ledger:E0772, ledger:E0871</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC intake air</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2BA96" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3FC" flags="0x30">
    <title>Torque Reduction Spark Retard - Maximum vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque reduction: largest spark retard a torque reduction may request, by coolant temperature. Stock 20, 30 and 40 degrees at -40, -20 and 0 C and 50 degrees from 20 C up. Effect: lower = less spark retard is available to a torque reduction at that temperature Evidence: ledger:E1130</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31A7C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3FD" flags="0x30">
    <title>Purge Amount - Hot Restart Factor vs Airflow</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount: during a hot restart, before normal purge is enabled, a small purge flow is requested by time since the start; this curve scales it by engine airflow (0 to 80 g/s). Stock 1.0 everywhere. Effect: lower = less purge during a hot restart at that airflow Evidence: ledger:E1121</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="2.5" />
      <LABEL index="2" value="5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="10" />
      <LABEL index="5" value="12.5" />
      <LABEL index="6" value="15" />
      <LABEL index="7" value="17.5" />
      <LABEL index="8" value="20" />
      <LABEL index="9" value="22.5" />
      <LABEL index="10" value="25" />
      <LABEL index="11" value="27.5" />
      <LABEL index="12" value="30" />
      <LABEL index="13" value="32.5" />
      <LABEL index="14" value="35" />
      <LABEL index="15" value="37.5" />
      <LABEL index="16" value="40" />
      <LABEL index="17" value="42.5" />
      <LABEL index="18" value="45" />
      <LABEL index="19" value="47.5" />
      <LABEL index="20" value="50" />
      <LABEL index="21" value="52.5" />
      <LABEL index="22" value="55" />
      <LABEL index="23" value="57.5" />
      <LABEL index="24" value="60" />
      <LABEL index="25" value="62.5" />
      <LABEL index="26" value="65" />
      <LABEL index="27" value="67.5" />
      <LABEL index="28" value="70" />
      <LABEL index="29" value="72.5" />
      <LABEL index="30" value="75" />
      <LABEL index="31" value="77.5" />
      <LABEL index="32" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2455A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3FE" flags="0x30">
    <title>Pedal Filter Factor vs Engine Run Time (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal filter factor by engine run time (0 to 200 s). Stock 1.0. The filter takes the largest of four terms: the run time, coolant and coolant above intake air factors multiplied together, the vehicle speed factor, a wheel acceleration factor and an axle torque factor. A factor of 1.0 gives the slowest filter (the pedal filter gain); lower makes the filter faster. On the stock file the last two terms are fixed at 1.0, so this curve has no effect. Effect: no effect on the stock file Evidence: ledger:E0768, ledger:E0945, ledger:E1118</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>s (engine run time)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="12.5" />
      <LABEL index="2" value="25" />
      <LABEL index="3" value="37.5" />
      <LABEL index="4" value="50" />
      <LABEL index="5" value="62.5" />
      <LABEL index="6" value="75" />
      <LABEL index="7" value="87.5" />
      <LABEL index="8" value="100" />
      <LABEL index="9" value="112.5" />
      <LABEL index="10" value="125" />
      <LABEL index="11" value="137.5" />
      <LABEL index="12" value="150" />
      <LABEL index="13" value="162.5" />
      <LABEL index="14" value="175" />
      <LABEL index="15" value="187.5" />
      <LABEL index="16" value="200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24070" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x3FF" flags="0x30">
    <title>Pedal Filter Factor vs Coolant Temperature (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal filter factor by coolant temperature, taken before the engine starts. Stock 1.0. The filter takes the largest of four terms: the run time, coolant and coolant above intake air factors multiplied together, the vehicle speed factor, a wheel acceleration factor and an axle torque factor. A factor of 1.0 gives the slowest filter (the pedal filter gain); lower makes the filter faster. On the stock file the last two terms are fixed at 1.0, so this curve has no effect. Effect: no effect on the stock file Evidence: ledger:E0768, ledger:E0945, ledger:E1118</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24094" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x400" flags="0x30">
    <title>Pedal Filter Factor vs Vehicle Speed (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal filter factor by vehicle speed (0 to 128 km/h). Stock 1.0. The filter takes the largest of four terms: the run time, coolant and coolant above intake air factors multiplied together, the vehicle speed factor, a wheel acceleration factor and an axle torque factor. A factor of 1.0 gives the slowest filter (the pedal filter gain); lower makes the filter faster. On the stock file the last two terms are fixed at 1.0, so this curve has no effect. Effect: no effect on the stock file Evidence: ledger:E0768, ledger:E0945, ledger:E1118</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="8" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="24" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="48" />
      <LABEL index="7" value="56" />
      <LABEL index="8" value="64" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="88" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="104" />
      <LABEL index="14" value="112" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x240CC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x401" flags="0x30">
    <title>Pedal Filter Factor vs Driveline Torque</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal filter factor by driveline output torque (engine torque through converter, gear and final drive, 0 to 8192 Nm). This is the axle torque factor: the filter takes the largest of the fade terms, and a factor of 1.0 gives the slowest filter (the pedal filter gain); lower makes the filter faster. Stock 1.0 everywhere, which holds the largest term at 1.0, so the other pedal filter factor curves have no effect on the stock file. Effect: lower = faster pedal filter at that torque, once no other term is higher Evidence: ledger:E0781, ledger:E0991, ledger:E1203</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>Nm (driveline output torque)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2412C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x402" flags="0x30">
    <title>Airflow Mode 2 - Engine Speed Factor vs Intake Air Temperature (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor applied to engine speed, by intake air temperature (minus 40 to 152 C), in the entry check of the throttle-area airflow mode. Stock 1.0 at every point. The stock calibration can never enter that airflow mode (its entry windows are all zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0772, ledger:E0863, ledger:E1466</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C9B0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x403" flags="0x30">
    <title>EVAP Engine-Off Test - Pressure Peak Factor vs Vapour Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: factor on the pressure peak stored at the end of the pressure phase, by fuel vapour temperature. Stock 1.0 everywhere. Effect: lower = the pressure peak counts for less at that vapour temperature Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (fuel vapour)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-10" />
      <LABEL index="1" value="-4.375" />
      <LABEL index="2" value="1.25" />
      <LABEL index="3" value="6.875" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.125" />
      <LABEL index="6" value="23.75" />
      <LABEL index="7" value="29.375" />
      <LABEL index="8" value="35" />
      <LABEL index="9" value="40.625" />
      <LABEL index="10" value="46.25" />
      <LABEL index="11" value="51.875" />
      <LABEL index="12" value="57.5" />
      <LABEL index="13" value="63.125" />
      <LABEL index="14" value="68.75" />
      <LABEL index="15" value="74.375" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x359EE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x404" flags="0x30">
    <title>EVAP Engine-Off Test - Pressure Peak Factor vs Vapour Temperature Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: factor on the pressure peak stored at the end of the pressure phase, by how much the fuel vapour temperature rose during the phase. Stock 1.0 everywhere. Effect: lower = the pressure peak counts for less at that temperature rise Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (fuel vapour rise)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.625" />
      <LABEL index="2" value="1.25" />
      <LABEL index="3" value="1.875" />
      <LABEL index="4" value="2.5" />
      <LABEL index="5" value="3.125" />
      <LABEL index="6" value="3.75" />
      <LABEL index="7" value="4.375" />
      <LABEL index="8" value="5" />
      <LABEL index="9" value="5.625" />
      <LABEL index="10" value="6.25" />
      <LABEL index="11" value="6.875" />
      <LABEL index="12" value="7.5" />
      <LABEL index="13" value="8.125" />
      <LABEL index="14" value="8.75" />
      <LABEL index="15" value="9.375" />
      <LABEL index="16" value="10" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35A12" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x405" flags="0x30">
    <title>Misfire - Minimum Load Coolant Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: multiplier of the minimum load curve by coolant temperature (-40 to 151 C). Stock 1.0 at every temperature. Effect: raise = the minimum load is higher at that coolant temperature Evidence: ledger:E0670, ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>16</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-27.25" />
      <LABEL index="2" value="-14.5" />
      <LABEL index="3" value="-1.75" />
      <LABEL index="4" value="11" />
      <LABEL index="5" value="23.75" />
      <LABEL index="6" value="36.5" />
      <LABEL index="7" value="49.25" />
      <LABEL index="8" value="62" />
      <LABEL index="9" value="74.75" />
      <LABEL index="10" value="87.5" />
      <LABEL index="11" value="100.25" />
      <LABEL index="12" value="113" />
      <LABEL index="13" value="125.75" />
      <LABEL index="14" value="138.5" />
      <LABEL index="15" value="151.25" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3920E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x406" flags="0x30">
    <title>Knock Learn Rate - Sample Count Curve</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is the sample count curve. Effect: raise = faster knock learning for under-sampled cylinders there Evidence: ledger:E0193, ledger:E0772, ledger:E0871</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>count (learn samples)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="2560" />
      <LABEL index="1" value="6400" />
      <LABEL index="2" value="10240" />
      <LABEL index="3" value="14080" />
      <LABEL index="4" value="17920" />
      <LABEL index="5" value="21760" />
      <LABEL index="6" value="25600" />
      <LABEL index="7" value="29440" />
      <LABEL index="8" value="33280" />
      <LABEL index="9" value="37120" />
      <LABEL index="10" value="40960" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2BAAA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x407" flags="0x30">
    <title>Knock Learn Rate - Engine Speed Curve</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is the engine speed curve. Effect: raise = faster knock learning for under-sampled cylinders there Evidence: ledger:E0193, ledger:E0772, ledger:E0871</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="800" />
      <LABEL index="1" value="1600" />
      <LABEL index="2" value="2400" />
      <LABEL index="3" value="3200" />
      <LABEL index="4" value="4000" />
      <LABEL index="5" value="4800" />
      <LABEL index="6" value="5600" />
      <LABEL index="7" value="6400" />
      <LABEL index="8" value="7200" />
      <LABEL index="9" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2BA6C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x408" flags="0x30">
    <title>Pedal Gain Reduction - Confirm Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the truck must accelerate at or above the pedal gain reduction acceleration threshold before the reduction starts, by driveline output torque (0 to 648 Nm). Stock 3200 s, so in effect never. Effect: lower = the pedal gain reduction starts sooner once the acceleration threshold is met Evidence: ledger:E0217, ledger:E0781, ledger:E1203</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>Nm (driveline output torque)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="81" />
      <LABEL index="2" value="162" />
      <LABEL index="3" value="243" />
      <LABEL index="4" value="324" />
      <LABEL index="5" value="405" />
      <LABEL index="6" value="486" />
      <LABEL index="7" value="567" />
      <LABEL index="8" value="648" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23120" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x409" flags="0x30">
    <title>Pedal Filter Factor vs Coolant Above Intake Air (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal filter factor by how far coolant is above intake air temperature (0 to 96 C). Stock 1.0. The filter takes the largest of four terms: the run time, coolant and coolant above intake air factors multiplied together, the vehicle speed factor, a wheel acceleration factor and an axle torque factor. A factor of 1.0 gives the slowest filter (the pedal filter gain); lower makes the filter faster. On the stock file the last two terms are fixed at 1.0, so this curve has no effect. Effect: no effect on the stock file Evidence: ledger:E0768, ledger:E0946, ledger:E1118</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (coolant above intake air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="12" />
      <LABEL index="2" value="24" />
      <LABEL index="3" value="36" />
      <LABEL index="4" value="48" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="72" />
      <LABEL index="7" value="84" />
      <LABEL index="8" value="96" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x240B8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x40A" flags="0x30">
    <title>Accelerator Pedal Filter - Fade Weight vs Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight on the largest fade term (run time, coolant, speed and other factors) before it is taken off the tracked filter gain, by that gain (0 to 100 %). Stock 1.0. Part of the accelerator pedal filter: the filtered pedal closes this share of its gap to the pedal demand every update; 1.0 follows the pedal at once. Effect: lower = the fade terms reduce the filter gain less at that gain Evidence: ledger:E0330, ledger:E0781, ledger:E1190</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>% (tracked gain)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="12.5" />
      <LABEL index="2" value="25" />
      <LABEL index="3" value="37.5" />
      <LABEL index="4" value="50" />
      <LABEL index="5" value="62.5" />
      <LABEL index="6" value="75" />
      <LABEL index="7" value="87.5" />
      <LABEL index="8" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24118" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x40B" flags="0x30">
    <title>EVAP Purge - Ramp Rate Falling, Highway</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the gap to the purge target closed on each purge update (about a tenth of a second) when commanded purge is falling at or above the speed split, by airflow. Stock 99.9 % (near instant). Effect: raise = purge follows its target faster Evidence: ledger:E0739, ledger:E1124</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24320" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x40C" flags="0x30">
    <title>EVAP Purge - Ramp Rate Rising, Highway</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the gap to the purge target closed on each purge update (about a tenth of a second) when commanded purge is rising at or above the speed split, by airflow. Stock 99.9 % (near instant). Effect: raise = purge follows its target faster Evidence: ledger:E0739, ledger:E1124</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24334" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x40D" flags="0x30">
    <title>LTFT Follow Rate vs MAP Change</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: how fast the applied long term trim moves to the value of the current cell, as the fraction of the gap closed every 12.5 ms, by the change of manifold pressure (-4 to +4 kPa against its filtered value). Stock 1.0 everywhere: the applied trim follows the cell at once. Effect: lower = the applied trim moves to a new cell value more gradually Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa MAP change</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-4" />
      <LABEL index="1" value="-3" />
      <LABEL index="2" value="-2" />
      <LABEL index="3" value="-1" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="1" />
      <LABEL index="6" value="2" />
      <LABEL index="7" value="3" />
      <LABEL index="8" value="4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24BF2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x40E" flags="0x30">
    <title>Idle Base Airflow - Baro Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air control: factor on the base idle airflow by barometric pressure (60 to 100 kPa). Stock 1.0 everywhere. Effect: raise = more base idle air at that barometric pressure Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="60" />
      <LABEL index="1" value="65" />
      <LABEL index="2" value="70" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="80" />
      <LABEL index="5" value="85" />
      <LABEL index="6" value="90" />
      <LABEL index="7" value="95" />
      <LABEL index="8" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A028" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x40F" flags="0x30">
    <title>Idle Airflow - Light-Off Retard Adder Coolant Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the idle air added for catalyst light-off spark retard, by coolant temperature (-40 to 152 C). Stock 1.0 everywhere. Effect: lower = less light-off idle air at that coolant temperature Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AA50" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x410" flags="0x0">
    <title>Vehicle Bus - Generator Field Duty Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Change in the generator field duty that triggers a new send of its message. Stock 1.0 %. Vehicle bus (serial data to the other modules): the message is sent again once at least the minimum interval has passed since it was last sent and the value has changed by at least the change threshold (or a status in it changed). Effect: lower = the duty is reported in finer steps Evidence: ledger:E0776, ledger:E0805, ledger:E1676</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20236" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x411" flags="0x0">
    <title>Vehicle Bus - Generator Field Duty Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum time between two sends of the generator field duty message. Stock 0.1 s. Vehicle bus (serial data to the other modules): the message is sent again once at least the minimum interval has passed since it was last sent and the value has changed by at least the change threshold (or a status in it changed). Effect: lower = sent more often Evidence: ledger:E0776, ledger:E0805, ledger:E1676</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20238" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x412" flags="0x0">
    <title>RPM Limit Hysteresis (Gear), Alternate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rev limiter: the wider in-gear hysteresis used once engine speed has hit the limiter the alternate count number of times (stock 8) without the count being reset; until then the normal in-gear hysteresis applies. The engine has to fall this far below the limit before the limiter lets go. Stock 1800 rpm. Effect: raise = after repeated limiter hits the engine must drop further before the limiter releases Evidence: ledger:E0769, ledger:E1258, ledger:E1442</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22B96" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x413" flags="0x0">
    <title>Rev Limit Hysteresis Mode Select</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Selects how the rev limiter hysteresis timer, which governs how the limiter comes back in after hitting the rev limit, is produced. Off resets the timer straight to its fixed default value; on calculates the timer from current running conditions instead. Stock is on. Effect: Turning it off makes the rev limiter hysteresis timer always start from its fixed default value; turning it on lets the timer be calculated from current running conditions. Evidence: ledger:E0776, ledger:E0800, ledger:E0805</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22BBE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x414" flags="0x0">
    <title>Rev Limit Hysteresis Alternate Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns an alternate, wider rev limiter hysteresis on or off. Off, the rev limiter always comes back in using the normal in-gear hysteresis. On, the wider alternate hysteresis becomes available once its own timing condition is met. Stock is on. Effect: Turning it off forces the rev limiter to always use the normal hysteresis; turning it on allows the wider alternate hysteresis to take over once its own condition is met. Evidence: ledger:E0769, ledger:E0800, ledger:E0805</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22BC0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x415" flags="0x0">
    <title>RPM Limit Hysteresis Alternate Count Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rev limiter: counts how many times engine speed rises above the limiter threshold; once the count reaches this value the larger alternate hysteresis is used (stock 1800 rpm instead of 300 rpm). The count is cleared after engine speed stays below the threshold for the alternate counter reset time. Stock 8. Effect: lower = the alternate hysteresis comes in after fewer limiter hits Evidence: ledger:E0769, ledger:E0804, ledger:E1258</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22BC2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>entries</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x416" flags="0x0">
    <title>Rev Limit Hysteresis Default Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The starting value of the rev limiter hysteresis timer, and also the time that timer must count up to before the hysteresis condition is considered satisfied. Stock is 3.0 seconds. Effect: Raising it means the rev limiter hysteresis timer starts higher and takes longer to satisfy its condition, so the limiter&#x27;s hysteresis behavior is reached later; lowering it reaches sooner. Evidence: ledger:E0776, ledger:E0800, ledger:E0805</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22BC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x417" flags="0x0">
    <title>Rev Limit Hysteresis Alternate Counter Reset Bound</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The starting value of a second rev limiter hysteresis timer, and also the time that timer must count up to before it stops resetting the alternate hysteresis selection counter. Stock is 3.0 seconds. Effect: Raising it makes this second timer take longer to reach its own cap, so the alternate hysteresis selection counter keeps getting reset for longer; lowering it shortens that. Evidence: ledger:E0769, ledger:E0800, ledger:E0805</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22BC6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x418" flags="0x0">
    <title>Rev Limit State Debounce Count (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of 25 ms rev limiter hysteresis task runs that must qualify before the debounced state takes effect, counted while an internal state flag is clear and the engine speed gate has tripped (stock 10). Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: reference only (rev limiter) Evidence: ledger:E0776, ledger:E0804, ledger:E0899</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22BFA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x419" flags="0x0">
    <title>Rev Limit State Timer Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the rev limiter&#x27;s state timer must run before the limiter&#x27;s state debounce count is cleared. Stock 3.0 seconds. Effect: raise = the state debounce count is kept longer before it is cleared Evidence: ledger:E0776, ledger:E0805</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22BFC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x41A" flags="0x0">
    <title>ETC Torque Limit Correction - Proportional Error Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a torque limit is active, the throttle control corrects the torque it uses to look up the ETC throttle limit with a proportional plus integral term on the error between the torque limit and the engine&#x27;s net torque (limit minus actual). With no limit active the correction is zero. The proportional term uses the error clamped to this minimum. Stock -50 Nm. Effect: lower = a bigger proportional pull-down when torque is over the limit Evidence: ledger:E0259, ledger:E0670, ledger:E0917</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3158A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x41B" flags="0x0">
    <title>ETC Torque Limit Correction - Proportional Error Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a torque limit is active, the throttle control corrects the torque it uses to look up the ETC throttle limit with a proportional plus integral term on the error between the torque limit and the engine&#x27;s net torque (limit minus actual). With no limit active the correction is zero. The proportional term uses the error clamped to this maximum. Stock 50 Nm. Effect: raise = a bigger proportional push-up when torque is under the limit Evidence: ledger:E0259, ledger:E0670, ledger:E0917</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3158C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x41C" flags="0x0">
    <title>ETC Torque Limit Correction - Integral Error Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a torque limit is active, the throttle control corrects the torque it uses to look up the ETC throttle limit with a proportional plus integral term on the error between the torque limit and the engine&#x27;s net torque (limit minus actual). With no limit active the correction is zero. Each integral step uses the error clamped to this minimum. Stock -15 Nm. Effect: lower = the integral term can fall faster Evidence: ledger:E0259, ledger:E0670, ledger:E0917</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3158E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x41D" flags="0x0">
    <title>ETC Torque Limit Correction - Integral Error Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a torque limit is active, the throttle control corrects the torque it uses to look up the ETC throttle limit with a proportional plus integral term on the error between the torque limit and the engine&#x27;s net torque (limit minus actual). With no limit active the correction is zero. Each integral step uses the error clamped to this maximum. Stock 15 Nm. Effect: raise = the integral term can climb faster Evidence: ledger:E0259, ledger:E0670, ledger:E0917</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x31590" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x41E" flags="0x0">
    <title>ETC Torque Limit Correction - Error Deadband</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a torque limit is active, the throttle control corrects the torque it uses to look up the ETC throttle limit with a proportional plus integral term on the error between the torque limit and the engine&#x27;s net torque (limit minus actual). With no limit active the correction is zero. Errors smaller than this (either sign) give no proportional term and no integral step. Stock 5 Nm. Effect: raise = the correction ignores bigger errors Evidence: ledger:E0259, ledger:E0670, ledger:E0917</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x31592" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x41F" flags="0x0">
    <title>ETC Torque Limit Correction - Integral Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a torque limit is active, the throttle control corrects the torque it uses to look up the ETC throttle limit with a proportional plus integral term on the error between the torque limit and the engine&#x27;s net torque (limit minus actual). With no limit active the correction is zero. The integral term is held at or above this. Stock 0 Nm, so it can only add torque. Effect: lower = the integral term can also take torque away Evidence: ledger:E0259, ledger:E0670, ledger:E0917</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x31594" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x420" flags="0x0">
    <title>ETC Torque Limit Correction - Integral Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a torque limit is active, the throttle control corrects the torque it uses to look up the ETC throttle limit with a proportional plus integral term on the error between the torque limit and the engine&#x27;s net torque (limit minus actual). With no limit active the correction is zero. The integral term is held at or below this. Stock 50 Nm. Effect: raise = the integral term can add more torque Evidence: ledger:E0259, ledger:E0670, ledger:E0917</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x31596" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x421" flags="0x0">
    <title>ETC Torque Limit Correction - Total Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a torque limit is active, the throttle control corrects the torque it uses to look up the ETC throttle limit with a proportional plus integral term on the error between the torque limit and the engine&#x27;s net torque (limit minus actual). With no limit active the correction is zero. The total correction (proportional plus integral) is held at or above this. Stock -65 Nm. Effect: lower = the correction can cut the throttle limit further Evidence: ledger:E0259, ledger:E0670, ledger:E0917</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x31598" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x422" flags="0x0">
    <title>ETC Torque Limit Correction - Total Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a torque limit is active, the throttle control corrects the torque it uses to look up the ETC throttle limit with a proportional plus integral term on the error between the torque limit and the engine&#x27;s net torque (limit minus actual). With no limit active the correction is zero. The total correction (proportional plus integral) is held at or below this. Stock 65 Nm. Effect: raise = the correction can open the throttle limit further Evidence: ledger:E0259, ledger:E0670, ledger:E0917</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3159A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x423" flags="0x0">
    <title>ETC Torque Limit Correction - Proportional Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a torque limit is active, the throttle control corrects the torque it uses to look up the ETC throttle limit with a proportional plus integral term on the error between the torque limit and the engine&#x27;s net torque (limit minus actual). With no limit active the correction is zero. The proportional term is the clamped error times this. Stock 0.50. Effect: raise = a stronger immediate correction Evidence: ledger:E0259, ledger:E0670, ledger:E0917</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3159C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x424" flags="0x0">
    <title>ETC Torque Limit Correction - Integral Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a torque limit is active, the throttle control corrects the torque it uses to look up the ETC throttle limit with a proportional plus integral term on the error between the torque limit and the engine&#x27;s net torque (limit minus actual). With no limit active the correction is zero. Each integral step adds the clamped error times this. Stock 0.40. Effect: raise = the integral term moves faster Evidence: ledger:E0259, ledger:E0670, ledger:E0917</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3159E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x425" flags="0x0">
    <title>ETC Torque Limit - Update Band Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A new throttle limit from the torque limit table is taken at once when it falls or rises by no more than this. Stock 2.00 % throttle. Effect: raise = larger rises are taken at once Evidence: ledger:E0670, ledger:E0917, ledger:E0926</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x315A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>-200.000000</min>
    <max>199.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x426" flags="0x0">
    <title>ETC Torque Limit - Update Band High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A rise at least this big is also taken at once; rises between the low and this value keep the previous limit. Stock 4.00 % throttle. Effect: lower = fewer rises are held back Evidence: ledger:E0670, ledger:E0917, ledger:E0926</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x315A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>-200.000000</min>
    <max>199.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x427" flags="0x0">
    <title>ETC Torque Limit Correction - Integral Step Period</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a torque limit is active, the throttle control corrects the torque it uses to look up the ETC throttle limit with a proportional plus integral term on the error between the torque limit and the engine&#x27;s net torque (limit minus actual). With no limit active the correction is zero. Time between integral steps after the first one. Stock 0.10 s. Effect: lower = more frequent integral steps Evidence: ledger:E0259, ledger:E0670, ledger:E0917</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x315A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x428" flags="0x0">
    <title>ETC Torque Limit Correction - First Integral Step Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a torque limit is active, the throttle control corrects the torque it uses to look up the ETC throttle limit with a proportional plus integral term on the error between the torque limit and the engine&#x27;s net torque (limit minus actual). With no limit active the correction is zero. Time from a limit becoming active to the first integral step. Stock 0.10 s. Effect: lower = the integral term starts sooner Evidence: ledger:E0259, ledger:E0670, ledger:E0917</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x315A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x429" flags="0x0">
    <title>P1574 Check - Vehicle Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): the check stops and waits for the arm speed again once vehicle speed falls to this. Stock 5 km/h. Effect: raise = the check stops at a higher speed Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A74" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x42A" flags="0x0">
    <title>P1574 Check - Arm Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): the check arms once vehicle speed reaches this. Stock 32 km/h. Effect: raise = the check arms at a higher speed Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A78" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x42B" flags="0x0">
    <title>STFT Tip-In Reset Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim: the tip-in reset is only allowed below this vehicle speed. Stock 10 km/h. Effect: raise = the tip-in reset also happens at higher speed Evidence: ledger:E1088</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24DF6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x42C" flags="0x0">
    <title>Hot-Restart Fuel - Latch Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot-restart fuel gate: a latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, the Open Loop Hot-Restart Gain table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. This is the latch coolant threshold. Stock 105 C. Effect: raise = the engine must run hotter before a hot restart is armed Evi...</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x298EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x42D" flags="0x0">
    <title>Learned MAF/VE Ratio - Deep Vacuum MAP</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM learns a MAF to VE airflow ratio in steady state and uses it on the VE airflow during transients. While manifold pressure is below the deep vacuum MAP (closed throttle decel) learning is frozen; on the first update back above it, a learned ratio below the reset threshold is put back to 1.0, and a higher one is kept. This is the deep vacuum MAP. Stock 20 kPa. Effect: raise = learning freezes over more of the decel range and the reset check runs more often Evidence: ledger:E0219, ledger:E0671, ledger:E0856</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2BDA0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x42E" flags="0x0">
    <title>VE Transient Window Check - Vehicle Speed Maximum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow: the alternate VE transient check (MAP change summed over a short window) only runs while vehicle speed is below this. Stock 255 km/h (no limit). The check itself never runs on the stock calibration (its throttle area limit is 0). This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0671, ledger:E0854, ledger:E1262</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C990" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x42F" flags="0x0">
    <title>Airmass Predictor Idle Region - MAP Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airmass predictor region: the PCM predicts cylinder airmass a little ahead of the MAF reading, with a separate set of predictor coefficients per region. The region is an idle window (low throttle, low engine speed, moderate vacuum) or one of 16 cells from four engine speed bands by four MAP bands. Leave these at stock unless the predictor coefficients are recalibrated with them. The idle region needs MAP below this. Stock 59 kPa. Effect: moves which predictor coefficient set applies Evidence: ledger:E0323, ledger:E0864</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2CA18" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x430" flags="0x0">
    <title>Airmass Predictor Idle Region - MAP At Or Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airmass predictor region: the PCM predicts cylinder airmass a little ahead of the MAF reading, with a separate set of predictor coefficients per region. The region is an idle window (low throttle, low engine speed, moderate vacuum) or one of 16 cells from four engine speed bands by four MAP bands. Leave these at stock unless the predictor coefficients are recalibrated with them. The idle region needs MAP at or above this. Stock 26 kPa. Effect: moves which predictor coefficient set applies Evidence: ledger:E0323, ledger:E0864</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2CA1A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x431" flags="0x0">
    <title>Cam Signal Lost Test - Run Condition, Airflow Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam position sensor signal lost test (P0340 / P0365): least airflow for the test to run. Stock 0 g/s (no limit). Effect: raise = the test only runs above this airflow Evidence: ledger:E1080</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x432" flags="0x0">
    <title>Misfire - Dead Cylinder Exemption Load Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: highest load at which a single dead cylinder is exempt from the catalyst-damage limit. Stock 30 %. Effect: raise = the exemption reaches higher load Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x433" flags="0x30">
    <title>EVAP Engine-Off Test - Disturbance Threshold vs Fuel Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP leak test: change of the filtered tank reading within one disturbance check interval, by fuel level, above which a disturbance is flagged (tank pressure sensor noise or a sudden pressure change). Stock 0.45 inH2O at every fuel level. Effect: raise = a larger pressure change is tolerated before a disturbance is flagged Evidence: ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36114" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>inH2O</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x434" flags="0x30">
    <title>Low Oil Pressure Check - Minimum Oil Pressure vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With the oil pressure sensor path on: minimum oil pressure for the engine speed. When the engine is running and oil pressure stays below this value, the PCM sets its low oil pressure state; it clears once oil pressure reaches this value plus the recovery margin. Stock 0 kPa at 0 rpm, 35 kPa around idle, rising to 216 kPa at high engine speed. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: lower values make the low oil pressure warning less sensitive Evidence: ledger:E0673, ledger:E1827, ledger:E1831</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36156" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x435" flags="0x30">
    <title>Engine Oil Pressure vs Sensor Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil pressure the PCM reads from the oil pressure sensor voltage (the value the scan tool shows as engine oil pressure) when the sensor path is on. Stock 0 kPa up to 0.3 V, then rising about 77 kPa per 0.3 V to 882 kPa at 4.7 V and above. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = a higher oil pressure is read for the same sensor voltage Evidence: ledger:E0674, ledger:E1410, ledger:E1831</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>V</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.000" />
      <LABEL index="1" value="0.312" />
      <LABEL index="2" value="0.625" />
      <LABEL index="3" value="0.938" />
      <LABEL index="4" value="1.250" />
      <LABEL index="5" value="1.562" />
      <LABEL index="6" value="1.875" />
      <LABEL index="7" value="2.188" />
      <LABEL index="8" value="2.500" />
      <LABEL index="9" value="2.812" />
      <LABEL index="10" value="3.125" />
      <LABEL index="11" value="3.438" />
      <LABEL index="12" value="3.750" />
      <LABEL index="13" value="4.062" />
      <LABEL index="14" value="4.375" />
      <LABEL index="15" value="4.688" />
      <LABEL index="16" value="5.000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x225C2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x436" flags="0x30">
    <title>Engine Oil Pressure Estimate vs Coolant and RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil pressure the PCM estimates from coolant temperature (-40 to 152 C) and engine speed (400 to 3600 rpm) when it runs without an oil pressure sensor (stock). The estimate is smoothed and sent on the vehicle bus (Class 2 message 4B11, 4 kPa per count), the value the oil pressure gauge shows. Stock about 415 to 496 kPa at -40 C and 240 to 470 kPa once warm, rising with engine speed. Effect: changes the oil pressure the PCM reports Evidence: ledger:E0274, ledger:E0675, ledger:E1246, ledger:E1408, ledger:E1831</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x225F2" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x437" flags="0x30">
    <title>P0116 Test - Startup Coolant Above Intake Air Fail Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant rationality test (P0116): the code sets outright when coolant at start-up is at least this much warmer than intake air, by intake air temperature. Stock 100 C everywhere. Effect: lower = a smaller coolant to intake air gap fails the test Evidence: ledger:E1011, ledger:E1288</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (intake air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3515A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x438" flags="0x30">
    <title>Misfire - Minimum Load</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: load below which misfire detection is paused, by engine speed (400 to 6500 rpm; at 7000 rpm and above there is no minimum). The value is multiplied by the coolant factor curve. Stock 20 % at 400 rpm, 14 % from 800 to 1600 rpm, rising to 43 % at 6500 rpm. Effect: raise = misfire detection is paused up to a higher load Evidence: ledger:E0676, ledger:E1065</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x38AB0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>26</indexcount>
      <units>rpm</units>
      <embedinfo type="1" />
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x391D8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="26" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>1</decimalpl>
      <min>0.000000</min>
      <max>199.996948</max>
      <MATH equation="X/327.68"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x439" flags="0x30">
    <title>Catalyst Monitor - RPM Span Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): largest engine speed movement allowed during a test: first value before the fuel steps, second value during them. More movement ends the test. Stock 500 rpm. Effect: raise = more engine speed movement is tolerated during a test Evidence: ledger:E1082</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>phase</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="before the fuel steps" />
      <LABEL index="1" value="during the fuel steps" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x345C6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x43A" flags="0x0">
    <title>P0125 / P0128 Check - Airflow Counted Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: airflow above this is counted as this much when the checks add up the air the engine has drawn since start. Stock 55 g/s. Effect: raise = high airflow counts in full toward the required air mass Evidence: ledger:E0776, ledger:E0805, ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35184" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x43B" flags="0x30">
    <title>P0125 / P0128 Check - Start-Up Coolant Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: each check only runs on starts where coolant temperature at start-up was at or below its value here. Stock 36.25 degC for P0125 and 75 degC for P0128. Effect: raise = the check also runs after warmer starts Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>check</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="P0125" />
      <LABEL index="1" value="P0128" />
      <LABEL index="2" value="third column (unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x351F0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x43C" flags="0x30">
    <title>P0125 / P0128 - Coolant Target Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: coolant must have reached this by the time the engine has drawn the required air mass; reaching it reports a pass. Stock 36.25 degC for P0125 and 80 degC for P0128 (the thermostat check). Effect: lower = a cooler running engine still passes Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>check</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="P0125" />
      <LABEL index="1" value="P0128" />
      <LABEL index="2" value="third column (unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x351F6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x43D" flags="0x30">
    <title>P0125 / P0128 Check - Distance Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: each check only fails once the vehicle has also been driven this far since start. Stock 0.57 km for P0125 and 1.71 km for P0128. Effect: raise = more distance is needed before the code can set Evidence: ledger:E1056</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>check</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="P0125" />
      <LABEL index="1" value="P0128" />
      <LABEL index="2" value="third column (unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x351FC" mmedelementsizebits="32" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1193046.470833</max>
      <MATH equation="X/3600"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x43E" flags="0x30">
    <title>P0443 Circuit Check - Fault Count and Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge valve circuit check P0443: the code sets once the first value&#x27;s number of faulted samples is reached; if the second value&#x27;s number of samples is reached first, the check passes and both counts start again. Stock 100 and 120. Effect: raise the first value = more faulted samples are needed to set the code; raise the second = each window is longer Evidence: ledger:E1058</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>value</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="fault samples to fail" />
      <LABEL index="1" value="window samples to pass" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37AE0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x43F" flags="0x0">
    <title>P1574 Check - Deceleration Speed Drop</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): a deceleration is counted when vehicle speed falls by at least this much inside the deceleration window. Stock 4 km/h. Effect: raise = only harder decelerations are counted Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A70" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x440" flags="0x0">
    <title>P1574 Check - Deceleration Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): the speed drop is measured from a reference speed that is refreshed after this long. Stock 0.5 s. Effect: raise = slower decelerations are also counted Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A72" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x441" flags="0x0">
    <title>P1574 Check - Speed Signal Difference Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1574 check (compares switch inputs during decelerations): the check restarts if its two vehicle speed signals differ by this much or more. Stock 10 km/h. Effect: raise = a larger speed signal difference is tolerated Evidence: ledger:E1049</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A76" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x442" flags="0x30">
    <title>P1689 Circuit Check - Fault Count and Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Output circuit check P1689 (switched off in the stock calibration): the code sets once the first value&#x27;s number of faulted samples is reached; if the second value&#x27;s number of samples is reached first, the check passes and both counts start again. Stock 100 and 120. Effect: raise the first value = more faulted samples are needed to set the code; raise the second = each window is longer Evidence: ledger:E1058</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>value</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="fault samples to fail" />
      <LABEL index="1" value="window samples to pass" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39A8E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x443" flags="0x0">
    <title>Crank Variation Learn - Arm RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn (the service procedure that clears P0315): sampling is armed once engine speed has risen above this. Stock 3970 rpm. Effect: raise = the engine must be revved higher before sampling is armed Evidence: ledger:E1040</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34586" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x444" flags="0x0">
    <title>Crank Variation Learn - Factor Average Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn: a learn is stored, and the stored factors are accepted (otherwise P0315 sets), only when the average of the five cylinder factors is below this. Stock 1.0008. Effect: raise = a learn with a higher average factor is accepted Evidence: ledger:E1081</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34590" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>26214.399994</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163840"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x445" flags="0x0">
    <title>Crank Variation Learn - Factor Average Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crankshaft variation learn: a learn is stored, and the stored factors are accepted (otherwise P0315 sets), only when the average of the five cylinder factors is above this. Stock 0.9992. Effect: lower = a learn with a lower average factor is accepted Evidence: ledger:E1081</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34594" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>26214.399994</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163840"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x446" flags="0x30">
    <title>Catalyst Monitor - First Step Downstream Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: if the downstream O2 sensor took longer than this to switch in the first fuel step, the catalyst is given the maximum storage time. Stock 5.9 s. Effect: lower = a slow downstream switch is scored as maximum storage sooner Evidence: ledger:E1000</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x346B6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x447" flags="0x30">
    <title>Catalyst Monitor - Storage Time Reference</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: each test&#x27;s oxygen storage time, after correction for airflow and catalyst temperature, is compared with this reference; the amount it falls short is the test result. Stock 3.0 s. Effect: lower = a catalyst with less oxygen storage still scores as good Evidence: ledger:E1021</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>bank</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x346BA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x448" flags="0x0">
    <title>Catalyst Monitor - Second Step Switch Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: in the second fuel step (lean, with the stock rich first step) each O2 sensor counts as switched once it reads at or below this. Stock 300 mV. Effect: raise = the sensors count as switched at a higher reading Evidence: ledger:E1000</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x346EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x449" flags="0x30">
    <title>Exhaust Temperature Model - Warm Flag Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Exhaust temperature model (read only by diagnostics): a channel counts as warm at or above this modelled temperature. Channel 3 is the catalyst channel: while it is warm the catalyst monitor (P0420) readiness counter counts up once per second (down while it is not), and the test can arm only once the counter reaches its threshold. The warm flags of channels 1 and 2 are not used on this calibration. Stock 450 C. The array has room for eight model channels; this engine uses three (one per O2 sensor plus the catalyst channel), so values 4 to 8 are never used. Effect: raise = the catalyst test needs a hotter modelled catalyst bef...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>model channel</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3524E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>1023.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x44A" flags="0x30">
    <title>Cam Angle Test - Angle Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam angle test (sets P0017 on this engine; runs with the cam phaser parked): lowest measured cam angle that counts as in range for a cylinder. Stock 48.8 deg. The second value belongs to the other cam input, which this test does not check. The array has room for four cam inputs; this engine has two, so the third and fourth values are never used. Effect: lower = a more retarded or advanced cam reading still passes Evidence: ledger:E1080, ledger:E1526</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input reporting P0365 / P0366 / P0017" />
      <LABEL index="1" value="cam input reporting P0340 / P0341 / P0016" />
      <LABEL index="2" value="cam input 3 (not fitted, unused)" />
      <LABEL index="3" value="cam input 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x367EC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-128.000000</min>
      <max>127.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x44B" flags="0x30">
    <title>Cam Angle Test - Angle Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam angle test (sets P0017 on this engine; runs with the cam phaser parked): highest measured cam angle that counts as in range for a cylinder. Stock 56.6 deg. The second value belongs to the other cam input, which this test does not check. The array has room for four cam inputs; this engine has two, so the third and fourth values are never used. Effect: raise = a larger cam angle reading still passes Evidence: ledger:E1080, ledger:E1526</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input reporting P0365 / P0366 / P0017" />
      <LABEL index="1" value="cam input reporting P0340 / P0341 / P0016" />
      <LABEL index="2" value="cam input 3 (not fitted, unused)" />
      <LABEL index="3" value="cam input 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x367F4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-128.000000</min>
      <max>127.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x44C" flags="0x30">
    <title>Cam Angle Test - Cylinders Out of Range</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam angle test (sets P0017 on this engine; runs with the cam phaser parked): number of the five per-cylinder angles that must be out of range for a sample to count as bad. Stock 2. The array has room for four cam inputs; this engine has two, so the third and fourth values are never used. Effect: raise = more cylinders must read out of range before a sample is bad Evidence: ledger:E1080, ledger:E1526</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input reporting P0365 / P0366 / P0017" />
      <LABEL index="1" value="cam input reporting P0340 / P0341 / P0016" />
      <LABEL index="2" value="cam input 3 (not fitted, unused)" />
      <LABEL index="3" value="cam input 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x367FC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>cylinders</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x44D" flags="0x30">
    <title>P0335 Count Test - Fail Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0335 crank count test (runs only while the engine turns on the cam signal with the crank signal not synchronised): bad samples that set P0335. Stock 8. Effect: raise = more bad samples are needed to set the code Evidence: ledger:E1080</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="crank sensor" />
      <LABEL index="1" value="not used" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36814" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x44E" flags="0x30">
    <title>P0335 Count Test - Counts Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0335 crank count test (runs only while the engine turns on the cam signal with the crank signal not synchronised): fewest crank counts per sample that count as good. Stock 90 (nominal 100). Effect: lower = fewer crank counts are accepted Evidence: ledger:E1080</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="crank sensor" />
      <LABEL index="1" value="not used" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36818" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>counts</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x44F" flags="0x30">
    <title>P0335 Count Test - Counts Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0335 crank count test (runs only while the engine turns on the cam signal with the crank signal not synchronised): most crank counts per sample that count as good. Stock 110 (nominal 100). Effect: raise = more crank counts are accepted Evidence: ledger:E1080</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="crank sensor" />
      <LABEL index="1" value="not used" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3681C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>counts</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x450" flags="0x30">
    <title>P0335 Count Test - Samples per Block</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0335 crank count test (runs only while the engine turns on the cam signal with the crank signal not synchronised): samples after which the bad sample count starts over if the fail count was not reached. Stock 10. Effect: raise = bad samples are collected over a longer block Evidence: ledger:E1080</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="crank sensor" />
      <LABEL index="1" value="not used" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36820" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x451" flags="0x0">
    <title>P0335 Count Test - Events per Sample</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0335 crank count test (runs only while the engine turns on the cam signal with the crank signal not synchronised): number of engine cycle events over which crank counts are added up for one sample. Stock 10. Effect: change together with the count limits: they are counts per sample Evidence: ledger:E1080</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36824" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>events</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x452" flags="0x30">
    <title>Cam Signal Lost Test - Pass Counts</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam position sensor signal lost test (P0365 / P0340): cam signal counts that must be seen within the fail time to pass. Stock 5 and 1. The array has room for four cam inputs; this engine has two, so the third and fourth values are never used. Effect: raise = more cam signal activity is needed to pass Evidence: ledger:E1080, ledger:E1526</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input reporting P0365 / P0366 / P0017" />
      <LABEL index="1" value="cam input reporting P0340 / P0341 / P0016" />
      <LABEL index="2" value="cam input 3 (not fitted, unused)" />
      <LABEL index="3" value="cam input 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3689C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>counts</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x453" flags="0x0">
    <title>Misfire - Abnormal Event Ratio Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: each detected event is classed as a normal misfire shape or an abnormal (disturbance) shape. When the abnormal events in a 200-revolution window exceed this percentage of the normal ones, the window is marked as a disturbance and gets no decision unless the disturbance override count is reached. Stock 50 %. Effect: raise = more abnormal events are tolerated before a window is set aside Evidence: ledger:E0780, ledger:E0805, ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39698" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x454" flags="0x0">
    <title>Misfire - Disturbance Override Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: a window marked as a disturbance (too many abnormal events, see the abnormal event ratio limit) normally gets no decision. When the window holds at least this many misfires it is judged anyway. Stock 90 misfires in 500 firings. Effect: lower = disturbed windows are judged at a lower misfire count Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3969A" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>misfires</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>127.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x455" flags="0x0">
    <title>Misfire - Emission Limit Multiplier After Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: multiplier applied to the emission limit during the first 16 windows (3200 revolutions) after start. Stock 1.0. Effect: raise = more misfire is tolerated in the first 3200 revolutions Evidence: ledger:E0780, ledger:E0805, ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3969C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction (Q12, 4096=1.0)</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x456" flags="0x0">
    <title>Misfire - Dead Cylinder Exemption Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: a window over the catalyst-damage limit is not counted as catalyst damaging when engine speed is at or below this, load is at or below the exemption load and one cylinder alone has the dead cylinder misfire count. The emission limit still applies. Stock 2000 rpm. Effect: raise = the exemption reaches higher engine speed Evidence: ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3969E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x457" flags="0x0">
    <title>Misfire - Emission Limit Multiplier, Special Period</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: multiplier applied to the emission limit for a calibrated period after an internal stored flag clears. That period is zero in the stock calibration, so this value is not used. Stock 1.0. Effect: no effect in the stock calibration Evidence: ledger:E0780, ledger:E0805, ledger:E1064</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction (Q12, 4096=1.0)</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x458" flags="0x30">
    <title>Purge Flow - Hot Restart Request vs Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge: purge flow requested during a hot restart, before normal purge is enabled, by time since the start (0 to 128 s). Stock 16 to 38. Purge flow units: the full scale word (stock 123) is full purge reference flow. Effect: raise = more purge right after a hot restart Evidence: ledger:E1122</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>s run time</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <LABEL index="17" value="68" />
      <LABEL index="18" value="72" />
      <LABEL index="19" value="76" />
      <LABEL index="20" value="80" />
      <LABEL index="21" value="84" />
      <LABEL index="22" value="88" />
      <LABEL index="23" value="92" />
      <LABEL index="24" value="96" />
      <LABEL index="25" value="100" />
      <LABEL index="26" value="104" />
      <LABEL index="27" value="108" />
      <LABEL index="28" value="112" />
      <LABEL index="29" value="116" />
      <LABEL index="30" value="120" />
      <LABEL index="31" value="124" />
      <LABEL index="32" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24512" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flow units</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x459" flags="0x30">
    <title>Purge Enable - Closed Loop Time Before First Purge vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: time in closed loop fuel control before the first purge of a trip, by coolant temperature at start (-40 to 152 C). Stock 290 s after a -40 C start down to 20 s from 80 C. Effect: raise = purge starts later after the engine goes closed loop Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC startup coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x245A4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x45A" flags="0x30">
    <title>Purge Enable - Coolant Offset Above Closed Loop Enable vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: purge may switch on only when coolant is above the closed loop enable coolant temperature plus this offset, by coolant temperature at start (-40 to 152 C). Stock 5 C after a very cold start rising to 17 C from a 20 C start (72 C at a 20 C start). Effect: raise = purge waits for a warmer engine Evidence: ledger:E0781, ledger:E0792, ledger:E0805, ledger:E0936, ledger:E1116</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC startup coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x245D0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x45B" flags="0x30">
    <title>O2 Sensor Ready - Run Time vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor ready logic: engine run time that must pass before an O2 sensor can be flagged ready, by coolant temperature at start-up. Stock 40 s cold to 3 s warm. Effect: raise = sensors are flagged ready later after a start Evidence: ledger:E1005, ledger:E1288</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29902" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x45C" flags="0x30">
    <title>Generator Control - Low Engine Speed Limit vs Desired Idle, Park / Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Park / Neutral. While the engine runs at or below this speed, looked up from the desired idle speed, the generator (alternator) control leaves its normal output command and uses its low speed command, until engine speed rises above it or the low speed time limit runs out. Stock 450 rpm at 500 rpm desired idle, 525 rpm from 600 rpm desired idle up. Effect: raise = the generator control switches to its low speed command at a higher engine speed Evidence: ledger:E0677, ledger:E1367</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="500" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="700" />
      <LABEL index="3" value="800" />
      <LABEL index="4" value="900" />
      <LABEL index="5" value="1000" />
      <LABEL index="6" value="1100" />
      <LABEL index="7" value="1200" />
      <LABEL index="8" value="1300" />
      <LABEL index="9" value="1400" />
      <LABEL index="10" value="1500" />
      <LABEL index="11" value="1600" />
      <LABEL index="12" value="1700" />
      <LABEL index="13" value="1800" />
      <LABEL index="14" value="1900" />
      <LABEL index="15" value="2000" />
      <LABEL index="16" value="2100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29950" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x45D" flags="0x30">
    <title>Desired Idle Minimum vs Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Desired idle: lowest desired idle speed by vehicle speed (0 to 40 km/h). It is one of the requests of which the largest wins. Stock 595 rpm up to 15 km/h and 875 rpm from 20 km/h, so the idle target is raised while the truck is rolling. Effect: raise = higher idle target at that road speed Evidence: ledger:E1112</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B090" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x45E" flags="0x30">
    <title>EVAP Purge - Ramp Rate Falling, Low Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the gap to the purge target closed on each purge update (about a tenth of a second) when commanded purge is falling below the speed split, by airflow. Stock 100 % (instant). Effect: raise = purge follows its target faster Evidence: ledger:E0739, ledger:E1124</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24348" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x45F" flags="0x30">
    <title>EVAP Purge - Ramp Rate Rising, Low Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the gap to the purge target closed on each purge update (about a tenth of a second) when commanded purge is rising below the speed split, by airflow. Stock 10 %, a gradual ramp-in. Effect: raise = purge follows its target faster Evidence: ledger:E0739, ledger:E1124</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2435C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x460" flags="0x30">
    <title>Torque Reduction - Fewest Fuelled Cylinders vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Torque reduction (traction control): fewest cylinders that stay fuelled, by coolant temperature. Stock 5 at every point, the full cylinder count, so no cylinder is ever cut for a torque reduction and the reduction is done with spark and throttle. Lower values allow fuel cut on some cylinders, which sends unburnt air to the catalyst. Effect: lower = cylinders may be cut during a torque reduction Evidence: ledger:E1130</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3154C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>cylinders</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x461" flags="0x0">
    <title>Diagnostic RPM Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. An engine speed ceiling used by a diagnostic monitor: below this speed the monitor&#x27;s alternate fault path can trigger, at or above it that path is skipped. Stock is 4200 rpm. Effect: Raising it raises the engine speed ceiling below which this monitor&#x27;s alternate fault path can trigger; lowering it lowers that ceiling. Evidence: ledger:E0776, ledger:E0805</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22C58" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x462" flags="0x0">
    <title>Crank and Cam Signal Loss Watchdog B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A companion watchdog timer that, once it reaches this value without seeing a qualifying crank or cam signal event, forces engine speed, mass airflow and related running values back to zero. Stock is 0.8 seconds. Effect: Raising it allows a longer gap since the last qualifying crank or cam signal event before this watchdog resets those readings; lowering it makes the watchdog trip sooner. Evidence: ledger:E0775, ledger:E0805</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x22CB1" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x463" flags="0x0">
    <title>Throttle Position Check Settle Timer</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A settle time that must elapse before the throttle-position pass/fail check below it is evaluated. Stock is 0.5 seconds. Effect: Raising it extends the settle time before the throttle-position check is evaluated; lowering it shortens it. Evidence: ledger:E0775, ledger:E0805</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22EA2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x464" flags="0x0">
    <title>Throttle Position Pass/Fail Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the settle timer above has elapsed, the throttle position reading is compared against this percentage to decide pass or fail for this check. Stock is about 36.0 percent throttle. Effect: Raising it raises the throttle-position percentage the reading is compared against for this check; lowering it lowers that boundary. Evidence: ledger:E0775, ledger:E0805</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22EA4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x465" flags="0x0">
    <title>Throttle Monitor Over-Limit Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Electronic throttle safety monitor: how long the throttle request worked out from the pedal may stay above the monitor&#x27;s allowed ceiling before the monitor acts (it then holds the request at the ceiling and sets its fault state). Stock 0.19 seconds. This is a throttle safety check: do not raise it casually. Effect: raise = the throttle request may exceed the monitor ceiling for longer before the monitor acts Evidence: ledger:E0775, ledger:E0805, ledger:E1124</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x241AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x466" flags="0x0">
    <title>Purge O2 Feedback - Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: normal step of the purge factor, up when lean and down when rich. Stock 0.0075. Effect: raise = the purge amount follows the O2 sensor faster Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x243B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x467" flags="0x0">
    <title>Purge O2 Feedback - Factor Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: lowest value of the purge factor. Stock 0: purge can be taken away completely. Effect: raise = some purge always remains when the mixture is rich Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x243BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x468" flags="0x0">
    <title>Purge O2 Feedback - Factor at Key-On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge amount, O2 feedback: value of the purge factor at key-on. Stock 0.35: each trip starts with about a third of the full purge request. Effect: raise = each trip starts with more purge Evidence: ledger:E1117</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x243BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x469" flags="0x0">
    <title>Purge Enable - Fuelled Cylinders Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge enable: purge runs only with at least this many cylinders being fuelled. Stock 5: purge stops whenever a cylinder is cut (decel fuel cut, limiters). Effect: lower = purge keeps running with cylinders cut Evidence: ledger:E1116</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x245F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cylinders</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x46A" flags="0x0">
    <title>LTFT Learn Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Long term fuel trim: time between learn steps of a cell. Stock 1 s. Effect: lower = long term trim learns faster Evidence: ledger:E1087</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24AF2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x46B" flags="0x30">
    <title>Rear O2 Trim - Learned Offset Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: highest learned switch point offset, by airflow region. Stock 100 mV (125 mV in the mid and high airflow regions). Effect: raise = the rear sensor may raise the switch point further Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>airflow region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="low airflow" />
      <LABEL index="1" value="closed throttle idle" />
      <LABEL index="2" value="mid airflow" />
      <LABEL index="3" value="high airflow" />
      <LABEL index="4" value="not used on stock" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24C14" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x46C" flags="0x30">
    <title>Rear O2 Trim - Learned Offset Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: lowest learned switch point offset, by airflow region. Stock -50 mV, -25 mV at idle, -60 mV in the mid and high airflow regions. Effect: lower = the rear sensor may lower the switch point further Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>airflow region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="low airflow" />
      <LABEL index="1" value="closed throttle idle" />
      <LABEL index="2" value="mid airflow" />
      <LABEL index="3" value="high airflow" />
      <LABEL index="4" value="not used on stock" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24C1E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x46D" flags="0x30">
    <title>Rear O2 Trim - Learn Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: time the rear sensor must stay rich or lean for each learn step, by airflow region. Stock 1.0 s, 1.5 s at idle, 0.5 s in the mid and high airflow regions. Effect: lower = the offset is learned faster Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>airflow region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="low airflow" />
      <LABEL index="1" value="closed throttle idle" />
      <LABEL index="2" value="mid airflow" />
      <LABEL index="3" value="high airflow" />
      <LABEL index="4" value="not used on stock" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24C28" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x46E" flags="0x0">
    <title>Rear O2 Trim - Not Active Band, Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: lower edge of the rear sensor not-active band; a reading at or below it counts toward the active time. Stock 350 mV. Effect: lower = a leaner reading is needed to count as activity Evidence: ledger:E1089</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24D98" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x46F" flags="0x30">
    <title>Rear O2 Trim - Rear O2 Lean Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: filtered rear O2 voltage at or below which the rear sensor counts as lean (the learned offset then moves up), by airflow region. Stock 625 mV, 650 mV at idle, 600 mV in the mid and high airflow regions. Row 2 is for a second bank, which this single-bank engine does not have: it has no effect on the stock calibration (dormant). Effect: raise = the rear sensor counts as lean at a higher voltage Evidence: ledger:E1089, ledger:E1386</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>airflow region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="low airflow" />
      <LABEL index="1" value="closed throttle idle" />
      <LABEL index="2" value="mid airflow" />
      <LABEL index="3" value="high airflow" />
      <LABEL index="4" value="not used on stock" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>bank</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24D9A" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x470" flags="0x30">
    <title>Rear O2 Trim - Rear O2 Rich Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rear O2 trim of the front O2 switch point: filtered rear O2 voltage at or above which the rear sensor counts as rich (the learned offset then moves down), by airflow region. Stock 660 mV, 700 mV at idle, 625 mV in the mid and high airflow regions. Row 2 is for a second bank, which this single-bank engine does not have: it has no effect on the stock calibration (dormant). Effect: lower = the rear sensor counts as rich at a lower voltage Evidence: ledger:E1089, ledger:E1386</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>airflow region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="low airflow" />
      <LABEL index="1" value="closed throttle idle" />
      <LABEL index="2" value="mid airflow" />
      <LABEL index="3" value="high airflow" />
      <LABEL index="4" value="not used on stock" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>bank</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24DAE" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x471" flags="0x0">
    <title>Acceleration Fuel Adder - Short Term Trim Hold Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel: fuel-removing steps of the short term trim are held while the acceleration fuel adder is at or above this much fuel per injection. Stock 2000 mg. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: lower = the trim stops removing fuel at a smaller acceleration adder Evidence: ledger:E1139</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E3E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>mg</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>2047.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x472" flags="0x0">
    <title>Transient Fuel - Tip-Out Film Shrink Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Transient fuel, tip-out mode: the mode is kept only while the wall film of the cylinder shrinks by at least this much per injection. Stock 0 mg: the mode ends as soon as the film starts to grow. Effect: raise = the tip-out mode ends earlier, while the film is still shrinking slowly Evidence: ledger:E1139</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2666A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mg</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x473" flags="0x0">
    <title>Hot-Restart Fuel - Latch Corrected Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot-restart fuel gate: a latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, the Open Loop Hot-Restart Gain table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. This is the corrected coolant threshold that arms the latch on its own. Stock 120 C. Effect: raise = the corrected-coolant pat...</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x298EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x474" flags="0x0">
    <title>Hot-Restart Fuel - Maximum Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Hot-restart fuel gate: a latch sets while the engine is hot (coolant above the latch coolant threshold with intake air above the latch intake threshold, or corrected coolant above its own threshold). On the next start, if the soak lasted between the minimum and maximum soak times, coolant is above the minimum coolant and run time is under the maximum run time, the Open Loop Hot-Restart Gain table multiplies open-loop fuel; it drops out once coolant falls to the minimum or run time reaches the maximum. This is the maximum run time after the start. Stock 45 s. Effect: raise = hot-restart fuel stays on longer after the start Evi...</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x298EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x475" flags="0x0">
    <title>O2 Sensor Ready - Active Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor ready logic: a sensor is flagged ready once more than this many samples have read outside the resting band. Stock 10. Effect: raise = more activity is needed before a sensor is flagged ready Evidence: ledger:E1005</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2994C" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x476" flags="0x30">
    <title>Idle A/C - Adder Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air, A/C clutch handshake: how long the idle air adder is held before it decays: first value at A/C clutch release, second at engagement. Stock 0.25 s each. Effect: raise = the extra idle air is held longer Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>event</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="A/C clutch release" />
      <LABEL index="1" value="A/C clutch engage" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29C68" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x477" flags="0x0">
    <title>Idle A/C Handshake - Throttle Closed Area Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C clutch idle handshake: the throttle counts as closed only with the throttle area above the idle area at or below this (and the throttle at or below the throttle closed threshold). Stock 0.006 %. Effect: raise = a slightly open throttle still counts as closed for the A/C handshake Evidence: ledger:E1106</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29C6C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x478" flags="0x30">
    <title>Idle Airflow Learn - Reset Values</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn: values the learned idle airflow starts from after the keep-alive memory is reset, for A/C off and A/C on. Stock 0 g/s for both. Effect: raise = the learn starts from more airflow after a memory reset Evidence: ledger:E1106</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>learn cell</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="A/C off" />
      <LABEL index="1" value="A/C on" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29CAC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x479" flags="0x0">
    <title>Desired Idle - During Traction Control Torque Reduction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Desired idle: idle speed requested while traction control is reducing engine torque, and afterwards for as long as the truck is slower than the request hold speed. It is one of the idle requests of which the largest wins. Stock 700 rpm. Effect: raise = higher idle target during and just after a traction control event Evidence: ledger:E1115</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B08C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x47A" flags="0x0">
    <title>Airmass Estimate Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lag filter gain (fraction of the new sample blended in each update) applied to the engine&#x27;s mass airflow estimate. A value of 100 percent makes the filtered estimate follow each new reading immediately, with no smoothing; lower values blend in only part of each reading, smoothing out noise between updates. Stock value blends in about 15.5 percent of the new reading on every update. TunerPro shows the gain as a fraction of the new sample blended in per update: 1.0 follows each reading instantly (100 percent), lower values smooth more. Effect: raise = the airflow estimate follows a new mass airflow reading faster; lower =...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C72E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x47B" flags="0x0">
    <title>Volumetric Efficiency Maximum Limit Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below the dynamic airflow MAF-only engine speed (stock 5000 rpm), the cylinder airmass that spark and fuel use is capped at this maximum VE x barometric pressure / charge temperature x the limit multiplier (and x the learned MAF to VE ratio when that is above 1.0). Barometric pressure, not MAP, so under boost this cap holds the airmass near a naturally aspirated full charge whatever the MAF reads: stock about 0.70 g per cylinder at 2000 rpm and 0.84 g at 5000 rpm (100 kPa, 20 C). Above the MAF-only engine speed the cap is skipped. This multiplies that cap. Stock 1.03. Effect: raise = higher airmass ceiling below the MAF-only...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C936" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier (1.0 = no change)</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x47C" flags="0x0">
    <title>VE Transient Mode - Window Entry Pressure Sum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While the transient mode is off, it starts when the manifold pressure change from the window start, summed over the window&#x27;s updates, rises above this (stock 1.5 kPa). Part of the window check of the volumetric efficiency transient mode, which runs only when its throttle gate is open; on the stock calibration that gate is closed, so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0780, ledger:E0854, ledger:E1429</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C98E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x47D" flags="0x30">
    <title>Spark Reference for Cam Target Reduction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Reference spark advance by rpm and airmass (0.08 to 1.36 g/cyl). When delivered spark stays below this reference for the Spark Reference Shortfall Confirm Time, the PCM starts reducing the load-based cam target: the Cam Target Spark-Limit Reduction factor (1.0 = no change) drops by its step down every down period, never below its floor, and climbs back once spark is at or above the reference. Stock flat -10 deg. The stock floor of 1.0 holds the factor at 1.0, so on the stock calibration this table changes nothing. Effect: raise = cam target reduction starts at higher delivered spark (only acts if the reduction floor is below...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl (airmass)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F885" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X/2"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x47E" flags="0x30">
    <title>Idle Airflow Closed Loop - Mode 2 MAP Target (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle MAP target by rpm and vehicle speed for the idle airflow closed loop&#x27;s mode 2, scaled by a coolant factor (1.2 cold to 1.0 warm); the loop steps idle air on the MAP error from it. Mode 2 is not selected on the stock H3 (mode 1 is), so this table has no effect as delivered. Stock 30 kPa flat (E0726). Effect: no effect on the stock H3 (mode 2 not selected) Evidence: ledger:E0686, ledger:E0726, ledger:E0929</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="8" />
      <LABEL index="2" value="16" />
      <LABEL index="3" value="24" />
      <LABEL index="4" value="32" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="48" />
      <LABEL index="7" value="56" />
      <LABEL index="8" value="64" />
      <LABEL index="9" value="72" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="88" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="104" />
      <LABEL index="14" value="112" />
      <LABEL index="15" value="120" />
      <LABEL index="16" value="128" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29EAC" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x47F" flags="0x30">
    <title>EVAP Purge Flow Model 1</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge flow model: the flow the PCM expects through the purge valve, by engine vacuum (rows, 0 to 80 kPa) and commanded purge (columns, 0 to 100 %). The EVAP leak test adds it up during its test phases and compares the total with its own limits to decide the phase. The PCM reads this table or EVAP Purge Flow Model 2 according to the state of one of its EVAP outputs. Shown raw. Reference only: changing it changes how the EVAP leak test judges the system and can hide or cause leak codes. DO NOT EDIT. Effect: reference only (EVAP leak test) Evidence: ledger:E0691, ledger:E0899, ledger:E0929, ledger:E0930</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>% (commanded evap purge)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="3.1" />
      <LABEL index="2" value="6.3" />
      <LABEL index="3" value="9.4" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="15.7" />
      <LABEL index="6" value="18.8" />
      <LABEL index="7" value="22.0" />
      <LABEL index="8" value="25.1" />
      <LABEL index="9" value="28.2" />
      <LABEL index="10" value="31.4" />
      <LABEL index="11" value="34.5" />
      <LABEL index="12" value="37.6" />
      <LABEL index="13" value="40.8" />
      <LABEL index="14" value="43.9" />
      <LABEL index="15" value="47.1" />
      <LABEL index="16" value="50.2" />
      <LABEL index="17" value="53.3" />
      <LABEL index="18" value="56.5" />
      <LABEL index="19" value="59.6" />
      <LABEL index="20" value="62.7" />
      <LABEL index="21" value="65.9" />
      <LABEL index="22" value="69.0" />
      <LABEL index="23" value="72.2" />
      <LABEL index="24" value="75.3" />
      <LABEL index="25" value="78.4" />
      <LABEL index="26" value="81.6" />
      <LABEL index="27" value="84.7" />
      <LABEL index="28" value="87.8" />
      <LABEL index="29" value="91.0" />
      <LABEL index="30" value="94.1" />
      <LABEL index="31" value="97.3" />
      <LABEL index="32" value="100.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>kPa (vacuum)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x368C6" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x480" flags="0x30">
    <title>EVAP Purge Flow Model 2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP purge flow model: the flow the PCM expects through the purge valve, by engine vacuum (rows, 0 to 80 kPa) and commanded purge (columns, 0 to 100 %). The EVAP leak test adds it up during its test phases and compares the total with its own limits to decide the phase. The PCM reads this table or EVAP Purge Flow Model 1 according to the state of one of its EVAP outputs. Shown raw. Reference only: changing it changes how the EVAP leak test judges the system and can hide or cause leak codes. DO NOT EDIT. Effect: reference only (EVAP leak test) Evidence: ledger:E0691, ledger:E0899, ledger:E0929, ledger:E0930</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>% (commanded evap purge)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="3.1" />
      <LABEL index="2" value="6.3" />
      <LABEL index="3" value="9.4" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="15.7" />
      <LABEL index="6" value="18.8" />
      <LABEL index="7" value="22.0" />
      <LABEL index="8" value="25.1" />
      <LABEL index="9" value="28.2" />
      <LABEL index="10" value="31.4" />
      <LABEL index="11" value="34.5" />
      <LABEL index="12" value="37.6" />
      <LABEL index="13" value="40.8" />
      <LABEL index="14" value="43.9" />
      <LABEL index="15" value="47.1" />
      <LABEL index="16" value="50.2" />
      <LABEL index="17" value="53.3" />
      <LABEL index="18" value="56.5" />
      <LABEL index="19" value="59.6" />
      <LABEL index="20" value="62.7" />
      <LABEL index="21" value="65.9" />
      <LABEL index="22" value="69.0" />
      <LABEL index="23" value="72.2" />
      <LABEL index="24" value="75.3" />
      <LABEL index="25" value="78.4" />
      <LABEL index="26" value="81.6" />
      <LABEL index="27" value="84.7" />
      <LABEL index="28" value="87.8" />
      <LABEL index="29" value="91.0" />
      <LABEL index="30" value="94.1" />
      <LABEL index="31" value="97.3" />
      <LABEL index="32" value="100.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>kPa (vacuum)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="10" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="25" />
      <LABEL index="6" value="30" />
      <LABEL index="7" value="35" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="45" />
      <LABEL index="10" value="50" />
      <LABEL index="11" value="55" />
      <LABEL index="12" value="60" />
      <LABEL index="13" value="65" />
      <LABEL index="14" value="70" />
      <LABEL index="15" value="75" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36D2E" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x481" flags="0x30">
    <title>Octane Scaler Start-Up Adjust vs Coolant and Intake Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added once at every engine start to each cylinder&#x27;s octane scaler, the share of the way from the High Octane toward the Low Octane spark table (0 to 1.0, also moved by octane learn). Negative moves toward High Octane. Stock -1.0 with a cold engine and cold intake, so a cold start begins on the High Octane table, rising to +0.10 when hot. Effect: raise = a start at that temperature moves the spark further toward the Low Octane table Evidence: ledger:E0296, ledger:E0695, ledger:E0937, ledger:E1218, ledger:E1641</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC (ECT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>degC (IAT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-16" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="32" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="104" />
      <LABEL index="7" value="128" />
      <LABEL index="8" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B93C" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>fraction</units>
      <decimalpl>0</decimalpl>
      <min>-4.000000</min>
      <max>3.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x482" flags="0x30">
    <title>Airflow Model - MAF/VE Ratio Start Value vs Baro and Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Starting value of the learned MAF-to-VE airmass ratio, by barometric pressure (columns, 65 to 105 kPa) and coolant temperature (rows, -20 to 101 C in 20.25 C steps). The engine then learns the ratio in steady running, clamped 0.5 to 1.5. Stock 1.05 to 1.25. Effect: raise = the learned MAF/VE airmass ratio starts higher at that baro / coolant, until steady-state learning corrects it Evidence: ledger:E0696, ledger:E0697, ledger:E0929</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="65" />
      <LABEL index="1" value="75" />
      <LABEL index="2" value="85" />
      <LABEL index="3" value="95" />
      <LABEL index="4" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>7</indexcount>
      <units>degC (ECT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-20.25" />
      <LABEL index="1" value="0" />
      <LABEL index="2" value="20.25" />
      <LABEL index="3" value="40.5" />
      <LABEL index="4" value="60.75" />
      <LABEL index="5" value="81" />
      <LABEL index="6" value="101.25" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2BDBA" mmedelementsizebits="16" mmedrowcount="7" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ratio (MAF / VE)</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x483" flags="0x30">
    <title>EVAP Engine-Off Test - Reference Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP small leak test (P0442): reference tank reading by ambient air temperature (rows, -10 to 80 C) and fuel level (columns, 0 to 100 %). The pressure phase is complete as soon as the tank reading reaches this, and the leak result is the shortfall of the pressure-to-vacuum swing against it. Stock -2.5 inH2O in every cell (2.5 inH2O of pressure; vacuum is positive, pressure negative). Changing it changes when the test passes or sets P0442. Effect: more negative = more tank pressure is needed for a full pass Evidence: ledger:E0698, ledger:E0899, ledger:E0935, ledger:E0936, ledger:E0939, ledger:E0944, ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC (ambient air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-10" />
      <LABEL index="1" value="-4.375" />
      <LABEL index="2" value="1.25" />
      <LABEL index="3" value="6.875" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.125" />
      <LABEL index="6" value="23.75" />
      <LABEL index="7" value="29.375" />
      <LABEL index="8" value="35" />
      <LABEL index="9" value="40.625" />
      <LABEL index="10" value="46.25" />
      <LABEL index="11" value="51.875" />
      <LABEL index="12" value="57.5" />
      <LABEL index="13" value="63.125" />
      <LABEL index="14" value="68.75" />
      <LABEL index="15" value="74.375" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x357AA" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>inH2O</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x484" flags="0x30">
    <title>EVAP Engine-Off Test - Reference Pressure (service test)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-off EVAP small leak test (P0442): the same reference for the scan tool started version of the test while its ambient temperature estimate is not yet valid, by ambient air temperature (rows, -10 to 80 C) and fuel level (columns, 0 to 100 %). Stock -2.5 inH2O in every cell (2.5 inH2O of pressure; vacuum is positive, pressure negative). Effect: more negative = more tank pressure is needed for a full pass Evidence: ledger:E0698, ledger:E0899, ledger:E0935, ledger:E0936, ledger:E0939, ledger:E0944, ledger:E1053</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC (ambient air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-10" />
      <LABEL index="1" value="-4.375" />
      <LABEL index="2" value="1.25" />
      <LABEL index="3" value="6.875" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="18.125" />
      <LABEL index="6" value="23.75" />
      <LABEL index="7" value="29.375" />
      <LABEL index="8" value="35" />
      <LABEL index="9" value="40.625" />
      <LABEL index="10" value="46.25" />
      <LABEL index="11" value="51.875" />
      <LABEL index="12" value="57.5" />
      <LABEL index="13" value="63.125" />
      <LABEL index="14" value="68.75" />
      <LABEL index="15" value="74.375" />
      <LABEL index="16" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35A82" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>inH2O</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x485" flags="0x30">
    <title>Catalyst Monitor - Storage Time Normaliser, Bank 2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplier applied to the measured catalyst oxygen storage time before it is compared with the storage time reference, by mean airflow during the lean fuel step (columns, 0 to 16 g/s) and modelled catalyst temperature (rows, 300 to 800 C). Higher values make the catalyst look better, so the efficiency code is less likely. Used only for a second catalyst bank; this calibration has one bank: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0699, ledger:E1021, ledger:E1191</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>g/s (mean airflow over the test step)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.5" />
      <LABEL index="2" value="1" />
      <LABEL index="3" value="1.5" />
      <LABEL index="4" value="2" />
      <LABEL index="5" value="2.5" />
      <LABEL index="6" value="3" />
      <LABEL index="7" value="3.5" />
      <LABEL index="8" value="4" />
      <LABEL index="9" value="4.5" />
      <LABEL index="10" value="5" />
      <LABEL index="11" value="5.5" />
      <LABEL index="12" value="6" />
      <LABEL index="13" value="6.5" />
      <LABEL index="14" value="7" />
      <LABEL index="15" value="7.5" />
      <LABEL index="16" value="8" />
      <LABEL index="17" value="8.5" />
      <LABEL index="18" value="9" />
      <LABEL index="19" value="9.5" />
      <LABEL index="20" value="10" />
      <LABEL index="21" value="10.5" />
      <LABEL index="22" value="11" />
      <LABEL index="23" value="11.5" />
      <LABEL index="24" value="12" />
      <LABEL index="25" value="12.5" />
      <LABEL index="26" value="13" />
      <LABEL index="27" value="13.5" />
      <LABEL index="28" value="14" />
      <LABEL index="29" value="14.5" />
      <LABEL index="30" value="15" />
      <LABEL index="31" value="15.5" />
      <LABEL index="32" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>degC (catalyst temperature model)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="300" />
      <LABEL index="1" value="362.5" />
      <LABEL index="2" value="425" />
      <LABEL index="3" value="487.5" />
      <LABEL index="4" value="550" />
      <LABEL index="5" value="612.5" />
      <LABEL index="6" value="675" />
      <LABEL index="7" value="737.5" />
      <LABEL index="8" value="800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3481F" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3.984375</max>
      <MATH equation="X/64"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x486" flags="0x30">
    <title>Purge Valve Duty vs Flow Demand</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge: purge valve duty for the purge flow demand (0 to 163 flow units; the demand is the flow request times the manifold vacuum factor). Stock 10 % at no demand rising to 100 %. Purge flow units: the full scale word (stock 123) is full purge reference flow. Effect: raise = more valve opening for that flow demand Evidence: ledger:E1122</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>flow units demand</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5.094" />
      <LABEL index="2" value="10.188" />
      <LABEL index="3" value="15.281" />
      <LABEL index="4" value="20.375" />
      <LABEL index="5" value="25.469" />
      <LABEL index="6" value="30.562" />
      <LABEL index="7" value="35.656" />
      <LABEL index="8" value="40.75" />
      <LABEL index="9" value="45.844" />
      <LABEL index="10" value="50.938" />
      <LABEL index="11" value="56.031" />
      <LABEL index="12" value="61.125" />
      <LABEL index="13" value="66.219" />
      <LABEL index="14" value="71.312" />
      <LABEL index="15" value="76.406" />
      <LABEL index="16" value="81.5" />
      <LABEL index="17" value="86.594" />
      <LABEL index="18" value="91.688" />
      <LABEL index="19" value="96.781" />
      <LABEL index="20" value="101.875" />
      <LABEL index="21" value="106.969" />
      <LABEL index="22" value="112.062" />
      <LABEL index="23" value="117.156" />
      <LABEL index="24" value="122.25" />
      <LABEL index="25" value="127.344" />
      <LABEL index="26" value="132.438" />
      <LABEL index="27" value="137.531" />
      <LABEL index="28" value="142.625" />
      <LABEL index="29" value="147.719" />
      <LABEL index="30" value="152.812" />
      <LABEL index="31" value="157.906" />
      <LABEL index="32" value="163" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2424C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.781250</max>
      <MATH equation="X/326.4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x487" flags="0x30">
    <title>MAP Plausibility - High Limit (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: the check&#x27;s enable is off, so it never runs. MAP plausibility check: every sample in which manifold pressure is above the high limit or below the low limit for the current engine speed and throttle area counts as out of band. When the out-of-band count reaches the fail count, the window ends as a failure; when the window reaches its sample count first, it ends as a pass. The high limit tops out near 104 kPa, so sustained boost would be counted out of band, but the check sets no code. This table is the high limit (kPa) by engine speed and throttle area. Stock 27.7 to 103.7 kPa. Effect: r...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="800" />
      <LABEL index="1" value="1600" />
      <LABEL index="2" value="2400" />
      <LABEL index="3" value="3200" />
      <LABEL index="4" value="4000" />
      <LABEL index="5" value="4800" />
      <LABEL index="6" value="5600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>11</indexcount>
      <units>% throttle area</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38884" mmedelementsizebits="16" mmedrowcount="11" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x488" flags="0x30">
    <title>MAP Plausibility - Low Limit (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: the check&#x27;s enable is off, so it never runs. MAP plausibility check: every sample in which manifold pressure is above the high limit or below the low limit for the current engine speed and throttle area counts as out of band. When the out-of-band count reaches the fail count, the window ends as a failure; when the window reaches its sample count first, it ends as a pass. The high limit tops out near 104 kPa, so sustained boost would be counted out of band, but the check sets no code. This table is the low limit (kPa) by engine speed and throttle area. Stock 10.3 to 57.2 kPa. Effect: low...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="800" />
      <LABEL index="1" value="1600" />
      <LABEL index="2" value="2400" />
      <LABEL index="3" value="3200" />
      <LABEL index="4" value="4000" />
      <LABEL index="5" value="4800" />
      <LABEL index="6" value="5600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>11</indexcount>
      <units>% throttle area</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38924" mmedelementsizebits="16" mmedrowcount="11" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x489" flags="0x0">
    <title>EVAP Purge - Fallback Duty</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded EVAP purge used when neither purge control feature is active. Stock 0 %, so purge is off in that case. Effect: raise = purge runs in the fallback case Evidence: ledger:E0739</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x241FA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x48A" flags="0x0">
    <title>EVAP Purge - Ramp Deadband</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded EVAP purge only moves toward its target once the gap is at least this; smaller gaps leave it where it is. Stock 2.0 %. Effect: raise = purge ignores larger target changes Evidence: ledger:E0739</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x241FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x48B" flags="0x0">
    <title>EVAP Purge - Ramp Tables Speed Split</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or above this vehicle speed the highway pair of purge ramp tables is used, below it the low-speed pair. Stock 50 km/h. Effect: moves where the highway purge ramp rates take over Evidence: ledger:E0739</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x241FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x48C" flags="0x30">
    <title>Idle Load State - Park/Neutral Delay Below Split Speed vs Trans Temp (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle tables, Park / Neutral or in gear rows: delay after a shift to Park / Neutral before the Park / Neutral rows are used, by transmission fluid temperature, below the split speed. The split speed is 0 on stock, so this curve is never used. Effect: no effect on this truck Evidence: ledger:E0293, ledger:E0742, ledger:E1113</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B28A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x48D" flags="0x30">
    <title>Idle Load State - In Gear Time-Out vs Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle tables, Park / Neutral or in gear rows: longest time after a shift into gear before the in gear rows of all idle tables are used, by transmission fluid temperature. They are used earlier when engine speed has dropped to the in gear confirm ratio. Stock 3.0 s cold down to 0.3 s warm. Effect: raise = the Park / Neutral rows stay in use longer after a shift into gear Evidence: ledger:E0293, ledger:E0742, ledger:E1113</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B2AE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x48E" flags="0x30">
    <title>Idle Airflow Shift into P/N Kick Factor, Extended Term, vs Trans Temp (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: factor on the extended part of the kick, by transmission fluid temperature. Stock 1.0. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck, so it has no effect. Effect: no effect on this truck Evidence: ledger:E0293, ledger:E0742, ledger:E1113</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B1D6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x48F" flags="0x30">
    <title>Idle Airflow Shift into Gear Kick Factor, Extended Term, vs Trans Temp (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into gear: factor on the extended part of the kick, by transmission fluid temperature. Stock 1.0. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck, so it has no effect. Effect: no effect on this truck Evidence: ledger:E0293, ledger:E0742, ledger:E1113</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B21E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x490" flags="0x30">
    <title>Shift into Gear Idle Kick, Extended Term Re-Arm Threshold vs Trans Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into gear: the extended part switches back on once transmission input speed has risen more than this since the shift, by transmission fluid temperature. Stock 100 rpm cold rising to 260 rpm hot. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0742, ledger:E1113, ledger:E1187</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC trans fluid</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B1B2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x491" flags="0x0">
    <title>Idle Airflow Kick - Shift into P/N Re-Arm Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: wait after the kick has faded before another one can be given. Stock 1 s. Effect: raise = longer wait between kicks Evidence: ledger:E1113</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B158" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x492" flags="0x0">
    <title>Shift into Park/Neutral Idle Kick, Reset Debounce Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On a fresh shift into Park or Neutral, this is the minimum time the shift-into-gear kick timer must already have been counting before the Park/Neutral kick&#x27;s own hold timer is reset. Stock 0.03 seconds. Effect: raise = a fresh Park/Neutral shift is less likely to reset the hold timer Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B156" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x493" flags="0x0">
    <title>Shift into Gear Idle Kick, Reset Debounce Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On a fresh shift into gear, this is the minimum time the Park/Neutral kick timer must already have been counting before the shift-into-gear kick&#x27;s own hold timer is reset. Stock 0.03 seconds. Effect: raise = a fresh gear shift is less likely to reset the hold timer Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B162" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x494" flags="0x0">
    <title>Shift into Park/Neutral Idle Kick, Extended Term Delay (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: time in Park / Neutral before the extended part of the kick switches on. Stock 0.05 s. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck, so it has no effect. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E1113</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B15C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x495" flags="0x0">
    <title>Shift into Gear Idle Kick, Settle Timer Maximum Duration</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Longest time the shift-into-gear idle-kick settle timer is allowed to keep running before it stops and clears its own internal flags. Stock 1.0 seconds. Effect: raise = the settle timer is allowed to run longer before it is forced to stop Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B15E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x496" flags="0x0">
    <title>Idle Airflow Adaptive Follower, Arm Throttle Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle position, at or below which the idle-air adaptive follower system is allowed to arm. Stock 0.0 percent. Effect: raise = the follower can arm at a higher throttle position Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B4BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x497" flags="0x0">
    <title>Idle Airflow Adaptive Follower, Disarm Throttle Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the arm throttle floor to set the throttle position above which an already-armed idle-air adaptive follower is disarmed and reset. Stock 0.0 percent. Effect: raise = the follower stays armed at a higher throttle position Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B4BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x498" flags="0x0">
    <title>Idle Airflow Adaptive Follower, Throttle Tracking Slew Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Maximum amount, in throttle percent, that the follower&#x27;s internal throttle-tracking figure is allowed to change on each pass. Stock 0.0 percent, which on this vehicle means that tracked figure never changes once initialized. Effect: raise = the tracked figure can change faster from one pass to the next Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B4B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x499" flags="0x30">
    <title>Idle Airflow Adaptive Follower, Throttle Bucket Points</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle-position break points used to sort the current throttle position into a bucket for the adaptive follower&#x27;s throttle correction. Cells are throttle percent values, not an output curve. Effect: n/a (breakpoint definition, not an output curve) Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B58A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.003052</max>
      <MATH equation="X/327.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x49A" flags="0x30">
    <title>Idle Airflow Adaptive Follower, Barometric Pressure Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the idle-air adaptive follower&#x27;s airflow build-up by barometric pressure. Stock 1.0 at every pressure point on this bin. Effect: raise = bigger follower airflow contribution at that pressure Evidence: ledger:E0750</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B50A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x49B" flags="0x0">
    <title>Shift to Park/Neutral Idle Kick, Hold Time Table Split Speed (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Picks which of two duration tables sets how long the extra part of the Park/Neutral idle-air bump keeps running: below this vehicle speed the 5-second table, at or above it an all-zero table. Stock 0 km/h, so the all-zero table is always picked and the extra part switches off at once on this truck (inactive). Effect: raise = allows the extended term at higher speeds Evidence: ledger:E0750, ledger:E1147</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B150" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x49C" flags="0x0">
    <title>Idle Airflow Kick - Shift into Gear RPM Margin</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into gear: the kick is given only when engine speed is not more than this above desired idle. Stock 200 rpm. Effect: raise = the kick is also given at higher engine speed Evidence: ledger:E1113</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B14A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x49D" flags="0x0">
    <title>Idle Load State - In Gear Confirm RPM Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle tables, Park / Neutral or in gear rows: after a shift into gear the in gear rows are used as soon as engine speed has fallen to this share of the engine speed at the shift (or when the time-out runs out). Stock 0.90. Effect: lower = a larger rpm drop is needed before the in gear rows are used Evidence: ledger:E1113</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B14C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x49E" flags="0x0">
    <title>Shift to Park/Neutral Idle Kick, Extended Term Re-Arm Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: the extended part switches back on once converter clutch slip is below this. Stock 50 rpm. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E1113, ledger:E1187</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B148" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x49F" flags="0x0">
    <title>Shift into Gear Idle Kick, Extended Term Speed Gate (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into gear: highest vehicle speed at the shift for the extended part of the kick. Stock 5 km/h. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck, so it has no effect. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E0898, ledger:E1113</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B154" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A0" flags="0x0">
    <title>Shift to Park/Neutral Idle Kick, Extended Term Speed Gate (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: highest vehicle speed at the shift for the extended part of the kick. Stock 15 km/h. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck, so it has no effect. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E0898, ledger:E1113</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B152" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A1" flags="0x0">
    <title>Idle Airflow Kick - Shift into P/N Fade Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: share of the remaining kick removed every 12.5 ms once its duration is over. Stock 0.5: it halves each pass. Effect: raise = the kick fades faster Evidence: ledger:E1113</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B142" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A2" flags="0x0">
    <title>Idle Airflow Kick - Shift into Gear Fade Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into gear: share of the remaining kick removed every 12.5 ms once its duration is over. Stock 0: the kick ends at once. Effect: raise from 0 = the kick fades out instead of ending at once (0.5 halves it each pass) Evidence: ledger:E1113</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B144" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A3" flags="0x0">
    <title>Idle Airflow Kick - Shift into P/N RPM Margin</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: the kick is given only when engine speed is not more than this above desired idle. Stock 100 rpm. Effect: raise = the kick is also given at higher engine speed Evidence: ledger:E1113</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B146" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A4" flags="0x0">
    <title>Shift into Gear Idle Kick, Base Amount Bias</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into gear: added to the turbine speed fall rate before the extended kick amount is looked up. Stock 2 rpm/s. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E1113, ledger:E1187</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B140" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm/s</units>
    <decimalpl>1</decimalpl>
    <min>-8000.000000</min>
    <max>7999.755859</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4.096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4A5" flags="0x0">
    <title>Shift to Park/Neutral Idle Kick, Base Amount Bias</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: added to the turbine speed fall rate before the extended kick amount is looked up. Stock 2 rpm/s. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E1113, ledger:E1187</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B13E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm/s</units>
    <decimalpl>1</decimalpl>
    <min>-8000.000000</min>
    <max>7999.755859</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4.096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x4A6" flags="0x30">
    <title>Idle Airflow Kick - Shift into Gear Extended Amount vs Turbine Speed Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into gear: extra airflow added by the extended part of the kick, by how fast the turbine speed is falling, plus the bias. Stock 0. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E0936, ledger:E1113, ledger:E1187</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm/s (turbine speed fall rate + bias)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-8000" />
      <LABEL index="1" value="-7000" />
      <LABEL index="2" value="-6000" />
      <LABEL index="3" value="-5000" />
      <LABEL index="4" value="-4000" />
      <LABEL index="5" value="-3000" />
      <LABEL index="6" value="-2000" />
      <LABEL index="7" value="-1000" />
      <LABEL index="8" value="0" />
      <LABEL index="9" value="1000" />
      <LABEL index="10" value="2000" />
      <LABEL index="11" value="3000" />
      <LABEL index="12" value="4000" />
      <LABEL index="13" value="5000" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="7000" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B18E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4A7" flags="0x30">
    <title>Idle Airflow Kick - Shift into P/N Extended Amount vs Turbine Speed Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow kick on a shift into Park / Neutral: extra airflow added by the extended part of the kick, by how fast the turbine speed is falling, plus the bias. Stock 0. It acts only on the extended part of the kick, which is switched off by its calibration switch on this truck: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0750, ledger:E0936, ledger:E1113, ledger:E1187</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm/s (turbine speed fall rate + bias)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-8000" />
      <LABEL index="1" value="-7000" />
      <LABEL index="2" value="-6000" />
      <LABEL index="3" value="-5000" />
      <LABEL index="4" value="-4000" />
      <LABEL index="5" value="-3000" />
      <LABEL index="6" value="-2000" />
      <LABEL index="7" value="-1000" />
      <LABEL index="8" value="0" />
      <LABEL index="9" value="1000" />
      <LABEL index="10" value="2000" />
      <LABEL index="11" value="3000" />
      <LABEL index="12" value="4000" />
      <LABEL index="13" value="5000" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="7000" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B16A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x4A8" flags="0x0">
    <title>Idle Airflow Adaptive Follower, Arm Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The idle airflow follower may arm only while measured throttle area above the idle area is at or below this (and throttle is at or below the arm throttle floor). Stock 0.006 %. Effect: raise = the follower may arm with more throttle area open Evidence: ledger:E0750, ledger:E1137, ledger:E1187</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B4B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x4A9" flags="0x30">
    <title>Throttle Follower Factor vs Speed (cruise engaged)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scales the follower target vs vehicle speed while cruise control is engaged (the other table is used otherwise). Stock 0.68 at 0 to 14 km/h, 1.0 above. Part of the idle throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. Effect: raise = more follower air after a lift while cruise control is engaged Evidence: ledger:E0292, ledger:E0750, ledger:E0838, ledger:E1187</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>km/h</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="14" />
      <LABEL index="2" value="28" />
      <LABEL index="3" value="42" />
      <LABEL index="4" value="56" />
      <LABEL index="5" value="70" />
      <LABEL index="6" value="84" />
      <LABEL index="7" value="98" />
      <LABEL index="8" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B5C2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>3.999939</max>
      <MATH equation="X/16384"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4AA" flags="0x30">
    <title>Throttle Follower Decay Step Limit vs Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit on the follower decay step, by throttle position (0 to 100 %). Stock no limit (32 g/s). Part of the idle throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. Effect: lower = follower air bleeds off more slowly at that throttle Evidence: ledger:E0292, ledger:E0750, ledger:E1187</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% throttle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B4C2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s per update</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>31.999512</max>
      <MATH equation="X/2048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4AB" flags="0x30">
    <title>Throttle Follower Rise Step Limit vs Throttle Area</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most the follower air may rise per update, by measured throttle area above the idle area (0 to 100 %). Stock 32 g/s (no limit). Part of the idle throttle follower (coast airflow): it holds extra idle airflow after a lift and lets it decay. Effect: lower = follower air builds up more slowly Evidence: ledger:E0750, ledger:E0936, ledger:E1137, ledger:E1187</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% throttle area</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B4E6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s per update</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4AC" flags="0x30">
    <title>Open Loop Commanded Mixture Coolant Temperature Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the open loop commanded fuel mixture by this factor, by modelled coolant temperature, while the computer runs one of its open loop mixture correction modes (the operating condition that selects this mode is still unidentified). A value of 1.0 makes no change; above 1.0 richens the open loop mixture at that temperature, below 1.0 leans it. Stock is 1.0 at every temperature, so it has no effect on the stock truck in any mode. Effect: raise = richer open loop mixture at this coolant temperature while this correction mode is active, lower = leaner. Stock is 1.0 (no effect) across the whole range. Evidence: ledger:E0752...</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC (modelled temperature)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2722E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier (1.0 = no change)</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4AD" flags="0x30">
    <title>Open Loop Commanded Mixture System Voltage Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the open loop commanded fuel mixture by this factor, by system voltage, while the computer runs one of its open loop mixture correction modes (the operating condition that selects this mode is still unidentified). A value of 1.0 makes no change. Values above 1.0 richen the open loop mixture at that voltage; values below 1.0 lean it out. Stock calibration holds this at 1.0 across the entire voltage range, so it currently has no effect on the truck. Effect: raise = richer open loop mixture at this system voltage while this correction mode is active, lower = leaner. Stock is 1.0 (no effect) across the whole range. Evi...</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>V (system)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x271E6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier (1.0 = no change)</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x4AE" flags="0x0">
    <title>Idle Air Integral - Step Down RPM Margin</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air control: the airflow integral may remove air only when engine speed is at least this far above desired idle. Stock 50 rpm. Effect: raise = the integral removes air only at a larger idle overshoot Evidence: ledger:E1092</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29DEC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4AF" flags="0x0">
    <title>Idle Predicted Airflow Floor - Speed Minimum With RPM Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: while the rpm airflow adder is in use, the predicted airflow floor applies only above this speed (as well as above the per gear speed gate). Stock 8 km/h. Effect: raise = the floor applies only at higher speed while the rpm adder is in use Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29DEE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4B0" flags="0x0">
    <title>Idle Airflow Correction Term - Input Filter (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this belongs to an idle airflow correction term whose output curve is all zero, so the term adds nothing. The term is added to the idle airflow sum at road speed with the throttle closed, outside decel fuel cut, once the idle airflow error has settled. This value is the filter speed of the term&#x27;s input, per update. Stock 0.05. Effect: no effect on the stock calibration Evidence: ledger:E0754, ledger:E0897</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29DEA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4B1" flags="0x0">
    <title>Idle Airflow Correction Term - Settled Error Threshold (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this belongs to an idle airflow correction term whose output curve is all zero, so the term adds nothing. The term is added to the idle airflow sum at road speed with the throttle closed, outside decel fuel cut, once the idle airflow error has settled. This value is the idle airflow error below which the term is allowed. Stock 1.0 g/s. Effect: no effect on the stock calibration Evidence: ledger:E0754, ledger:E0897</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29DE8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x4B2" flags="0x30">
    <title>Idle Airflow Closed-Loop Step - Airflow Error Breakpoints</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: the 17 airflow error values (measured minus predicted airflow) at which the cells of the closed loop step table sit. Stock -4 to +6 g/s. Keep them rising from left to right. Effect: move a breakpoint = the step cell at that position acts at a different airflow error Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>cell of the step table</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29DF4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x4B3" flags="0x0">
    <title>Idle Airflow Correction Term - Minimum Speed (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inactive on the stock calibration: this belongs to an idle airflow correction term whose output curve is all zero, so the term adds nothing. The term is added to the idle airflow sum at road speed with the throttle closed, outside decel fuel cut, once the idle airflow error has settled. This value is the minimum vehicle speed for the term. Stock 18 km/h. Effect: no effect on the stock calibration Evidence: ledger:E0754, ledger:E0897</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29DF0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4B4" flags="0x0">
    <title>Decel Fuel Cut Idle Air - First Target Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air during decel fuel cut: time the first target is held before the idle air moves to the second target. Stock 1 s. Effect: raise = the first target is held longer Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2AA76" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x4B5" flags="0x30">
    <title>Idle Base Airflow - Coolant Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the base idle airflow (Idle Airflow - Base vs RPM) by engine coolant temperature, applied together with the baro factor. Stock 1.0 at every coolant temperature. Effect: raise = more base idle airflow at that coolant temperature Evidence: ledger:E0754, ledger:E1370</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A03C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4B6" flags="0x30">
    <title>Idle Closed Loop, Alternate Mode MAP Target Coolant Factor (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant-temperature scaling factor for the target used by an alternate idle closed-loop calculation mode. That alternate mode is never selected on this vehicle, so this factor has no effect here (inactive). Stock 1.20 at the coldest point on this bin, tapering to 1.00 by normal operating temperature. Effect: n/a (alternate mode not selected on this vehicle) Evidence: ledger:E0754</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (ECT)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A060" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>15.999756</max>
      <MATH equation="X/4096"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x4B7" flags="0x0">
    <title>Decel Fuel Cut Idle Air - Rise Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air during decel fuel cut: step per 12.5 ms by which the idle air rises to its first target when fuel cut starts. Stock 32 g/s: it jumps to the target at once. Effect: lower = the idle air ramps in instead of jumping Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A966" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4B8" flags="0x0">
    <title>Decel Fuel Cut Idle Air - Step to Second Target</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air during decel fuel cut: step per 12.5 ms by which the idle air moves from the first target to the second target after the hold time. Stock 0.1 g/s (8 g/s per second). Effect: raise = the idle air reaches the second target sooner Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2A968" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x4B9" flags="0x30">
    <title>Decel Fuel Cut Idle Air - First Target vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air during decel fuel cut: idle air added right after fuel cut starts, by engine speed (0 to 4096 rpm). Stock 0 to 2.4 g/s. Effect: raise = more air through the throttle at the start of fuel cut Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A994" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4BA" flags="0x30">
    <title>Decel Fuel Cut Idle Air - Second Target vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle air during decel fuel cut: idle air for the rest of the fuel cut, after the hold time, by engine speed (0 to 4096 rpm). Stock 0 to -2.07 g/s: air is taken away. Effect: raise (less negative) = more air through the throttle during fuel cut Evidence: ledger:E1111</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A9B8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4BB" flags="0x30">
    <title>Idle Airflow - Coolant Term</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added by engine coolant temperature (stock 15.0 g/s at -40 C falling to 3.9 g/s from 92 C up). It is one of the terms summed into the predicted idle airflow that the idle controller opens the throttle for. Two rows: the PCM uses the second row when the idle calibration switch is on, which it is on this truck; the first row is the alternate. Each row keeps its own point count word. Effect: raise = more idle airflow (higher idle throttle opening) at that coolant temperature Evidence: ledger:E0287, ledger:E0754, ledger:E...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>row</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alternate (switch off)" />
      <LABEL index="1" value="used (switch on, stock)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A7D4" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4BC" flags="0x30">
    <title>Injector Short Pulse Width Correction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the commanded injector pulse width for a cylinder is below about 3.0 ms, this curve adds a correction onto it before it reaches the injector driver, compensating for injector nonlinearity at very short pulse widths. Above 3.0 ms the pulse width passes through unchanged. While the engine is running, the corrected result is never allowed below about 0.66 ms. Indexed by the uncorrected pulse width itself, 0 to 4.0 ms. Stock adds up to +0.17 ms at the shortest pulse widths, tapering to +0.016 ms by 4.0 ms. Effect: raise = more pulse width added back in at short injector pulse widths Evidence: ledger:E0755, ledger:E0936, ledg...</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>ms (pulse width)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.125" />
      <LABEL index="2" value="0.25" />
      <LABEL index="3" value="0.375" />
      <LABEL index="4" value="0.5" />
      <LABEL index="5" value="0.625" />
      <LABEL index="6" value="0.75" />
      <LABEL index="7" value="0.875" />
      <LABEL index="8" value="1" />
      <LABEL index="9" value="1.125" />
      <LABEL index="10" value="1.25" />
      <LABEL index="11" value="1.375" />
      <LABEL index="12" value="1.5" />
      <LABEL index="13" value="1.625" />
      <LABEL index="14" value="1.75" />
      <LABEL index="15" value="1.875" />
      <LABEL index="16" value="2" />
      <LABEL index="17" value="2.125" />
      <LABEL index="18" value="2.25" />
      <LABEL index="19" value="2.375" />
      <LABEL index="20" value="2.5" />
      <LABEL index="21" value="2.625" />
      <LABEL index="22" value="2.75" />
      <LABEL index="23" value="2.875" />
      <LABEL index="24" value="3" />
      <LABEL index="25" value="3.125" />
      <LABEL index="26" value="3.25" />
      <LABEL index="27" value="3.375" />
      <LABEL index="28" value="3.5" />
      <LABEL index="29" value="3.625" />
      <LABEL index="30" value="3.75" />
      <LABEL index="31" value="3.875" />
      <LABEL index="32" value="4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x252C2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>ms (pulse width)</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x4BD" flags="0x0">
    <title>Injector Short Pulse Width Correction Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this commanded pulse width, the short-pulse-width correction curve is applied; at or above it the commanded pulse width passes through unchanged. Stock 3.0 ms. Effect: raise = correction applies over a wider range of pulse widths Evidence: ledger:E0755</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x252B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ms (pulse width)</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4BE" flags="0x0">
    <title>Injector Short Pulse Width Correction Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While the engine is running, the corrected pulse width from the short-pulse-width correction is never allowed to fall below this value. Stock 0.656 ms. Effect: raise = corrected short pulse widths are floored higher Evidence: ledger:E0755</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x252BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ms (pulse width)</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4BF" flags="0x0">
    <title>Injector Short Pulse Width Correction Ceiling Guard</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. An overflow guard on the corrected pulse width: values above this are clamped down to it. Stock 464.0 ms, far above any real commanded pulse width, so this guard is not reached in normal operation. Effect: raise = the (practically unreachable) overflow guard moves higher Evidence: ledger:E0755</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x252BA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ms (pulse width)</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x4C0" flags="0x30">
    <title>Closed Loop O2 Filter Gain - Error Signal</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): filter on the O2 voltage that is used to work out how far the signal is past the switch point (the input of the step interval and proportional factors), by airflow. Share of each new reading taken every 12.5 ms. Stock 0.005 at idle rising to 0.1. Effect: raise = that signal follows the O2 sensor faster Evidence: ledger:E1126</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s used airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4.8" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="13.2" />
      <LABEL index="4" value="21.8" />
      <LABEL index="5" value="29.5" />
      <LABEL index="6" value="40.3" />
      <LABEL index="7" value="51.8" />
      <LABEL index="8" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24E42" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4C1" flags="0x30">
    <title>Closed Loop O2 Filter Gain - Purge Feedback Signal</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Front O2: filter on the O2 voltage that the canister purge feedback reads, by airflow. Share of each new reading taken every 12.5 ms. Stock 0.005 at idle rising to 0.14. Effect: raise = that signal follows the O2 sensor faster Evidence: ledger:E1126</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s used airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4.8" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="13.2" />
      <LABEL index="4" value="21.8" />
      <LABEL index="5" value="29.5" />
      <LABEL index="6" value="40.3" />
      <LABEL index="7" value="51.8" />
      <LABEL index="8" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24E6A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x4C2" flags="0x0">
    <title>EVAP Fuel Vapor Temperature - Default When Sensor Faulted</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP fuel vapour temperature sensor: vapour temperature used while the sensor circuit is faulted. Stock 20 C. Effect: sets the substitute vapour temperature Evidence: ledger:E0756, ledger:E1482</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x37A8E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x4C3" flags="0x30">
    <title>EVAP Fuel Vapor Temperature vs Sensor Resistance</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP fuel vapour temperature sensor: converts the sensor resistance into the fuel vapour temperature. The resistance axis is logarithmic, 4 to 2048 ohm in 33 points (nine doublings). Stock 88.3 C at 4 ohm down to -19.5 C at 2048 ohm. Effect: changes the reported vapour temperature for a given sensor resistance Evidence: ledger:E0756, ledger:E0937, ledger:E1482</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>ohm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="4.0" />
      <LABEL index="1" value="4.9" />
      <LABEL index="2" value="5.9" />
      <LABEL index="3" value="7.2" />
      <LABEL index="4" value="8.7" />
      <LABEL index="5" value="10.6" />
      <LABEL index="6" value="12.9" />
      <LABEL index="7" value="15.7" />
      <LABEL index="8" value="19.0" />
      <LABEL index="9" value="23.1" />
      <LABEL index="10" value="28.1" />
      <LABEL index="11" value="34.1" />
      <LABEL index="12" value="41.5" />
      <LABEL index="13" value="50.4" />
      <LABEL index="14" value="61.3" />
      <LABEL index="15" value="74.5" />
      <LABEL index="16" value="90.5" />
      <LABEL index="17" value="110.0" />
      <LABEL index="18" value="133.7" />
      <LABEL index="19" value="162.4" />
      <LABEL index="20" value="197.4" />
      <LABEL index="21" value="239.9" />
      <LABEL index="22" value="291.5" />
      <LABEL index="23" value="354.3" />
      <LABEL index="24" value="430.5" />
      <LABEL index="25" value="523.2" />
      <LABEL index="26" value="635.8" />
      <LABEL index="27" value="772.7" />
      <LABEL index="28" value="939.0" />
      <LABEL index="29" value="1141.1" />
      <LABEL index="30" value="1386.8" />
      <LABEL index="31" value="1685.3" />
      <LABEL index="32" value="2048.0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37A98" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4C4" flags="0x30">
    <title>A/C Clutch - Engage Delay vs Intake Air Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time from an A/C engage request to the compressor clutch being switched on, by intake air temperature. The extra A/C idle airflow is added during this delay, so the idle is ready before the compressor load arrives. Stock 0.25 s, 0.30 s at 79 C, 0.35 s from 84 C. Effect: raise = longer wait before the A/C compressor engages Evidence: ledger:E0756, ledger:E1865</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5.625" />
      <LABEL index="2" value="11.25" />
      <LABEL index="3" value="16.875" />
      <LABEL index="4" value="22.5" />
      <LABEL index="5" value="28.125" />
      <LABEL index="6" value="33.75" />
      <LABEL index="7" value="39.375" />
      <LABEL index="8" value="45" />
      <LABEL index="9" value="50.625" />
      <LABEL index="10" value="56.25" />
      <LABEL index="11" value="61.875" />
      <LABEL index="12" value="67.5" />
      <LABEL index="13" value="73.125" />
      <LABEL index="14" value="78.75" />
      <LABEL index="15" value="84.375" />
      <LABEL index="16" value="90" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x299C6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4C5" flags="0x30">
    <title>A/C Clutch - Disengage Delay vs Intake Air Temp</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time from an A/C disengage request to the compressor clutch being switched off, by intake air temperature. Stock 0.6 s at every temperature. Effect: raise = the A/C compressor stays engaged longer after it is asked to switch off Evidence: ledger:E0756, ledger:E1865</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5.625" />
      <LABEL index="2" value="11.25" />
      <LABEL index="3" value="16.875" />
      <LABEL index="4" value="22.5" />
      <LABEL index="5" value="28.125" />
      <LABEL index="6" value="33.75" />
      <LABEL index="7" value="39.375" />
      <LABEL index="8" value="45" />
      <LABEL index="9" value="50.625" />
      <LABEL index="10" value="56.25" />
      <LABEL index="11" value="61.875" />
      <LABEL index="12" value="67.5" />
      <LABEL index="13" value="73.125" />
      <LABEL index="14" value="78.75" />
      <LABEL index="15" value="84.375" />
      <LABEL index="16" value="90" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x299EA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4C6" flags="0x30">
    <title>EVAP Test Tank Vacuum Jump Limit B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Change in filtered tank vacuum between updates, by fuel level (0 to 100 %), that sets the second tank vacuum jump flag when the main flag is clear. Stock 32 inH2O in every cell, which is never reached. Effect: lower = a smaller tank vacuum jump sets the second flag Evidence: ledger:E0756, ledger:E0899, ledger:E0940, ledger:E0944, ledger:E1054</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x379C8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>inH2O</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4C7" flags="0x30">
    <title>EVAP Test Tank Vacuum Jump Limit A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Change in filtered tank vacuum between updates, by fuel level (0 to 100 %), that sets the main tank vacuum jump flag, which pauses the leak test integration and restarts its count. Stock 32 inH2O in every cell, which is never reached. Effect: lower = a smaller tank vacuum jump pauses the leak test Evidence: ledger:E0756, ledger:E0899, ledger:E0940, ledger:E0944, ledger:E1054</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% fuel level</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x379A4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>inH2O</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4C8" flags="0x30">
    <title>Transmission Throttle vs Throttle Area Request</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converts the throttle-area request above idle (from the pedal, or from cruise control) into the throttle value the transmission&#x27;s shift, TCC and WOT schedules are looked up with. Stock rises steeply at first (3 % request gives 17 %, 25 % gives 49 %) and reaches 100 % at about 97 %. Effect: raise = the transmission schedules see more throttle for the same request Evidence: ledger:E0756, ledger:E0964</description>
    <CATEGORYMEM index="0" category="10" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>% throttle area request above idle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="3.125" />
      <LABEL index="2" value="6.25" />
      <LABEL index="3" value="9.375" />
      <LABEL index="4" value="12.5" />
      <LABEL index="5" value="15.625" />
      <LABEL index="6" value="18.75" />
      <LABEL index="7" value="21.875" />
      <LABEL index="8" value="25" />
      <LABEL index="9" value="28.125" />
      <LABEL index="10" value="31.25" />
      <LABEL index="11" value="34.375" />
      <LABEL index="12" value="37.5" />
      <LABEL index="13" value="40.625" />
      <LABEL index="14" value="43.75" />
      <LABEL index="15" value="46.875" />
      <LABEL index="16" value="50" />
      <LABEL index="17" value="53.125" />
      <LABEL index="18" value="56.25" />
      <LABEL index="19" value="59.375" />
      <LABEL index="20" value="62.5" />
      <LABEL index="21" value="65.625" />
      <LABEL index="22" value="68.75" />
      <LABEL index="23" value="71.875" />
      <LABEL index="24" value="75" />
      <LABEL index="25" value="78.125" />
      <LABEL index="26" value="81.25" />
      <LABEL index="27" value="84.375" />
      <LABEL index="28" value="87.5" />
      <LABEL index="29" value="90.625" />
      <LABEL index="30" value="93.75" />
      <LABEL index="31" value="96.875" />
      <LABEL index="32" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31B06" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (transmission throttle)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4C9" flags="0x30">
    <title>Traction Control - Spark Retard Share vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control: factor on the part of a torque reduction that is handed to spark retard, by coolant temperature. Stock 0.1 cold rising to 1.0 hot: a cold engine gets little spark retard from traction control. Effect: raise = more of the traction control torque reduction is done with spark retard at that temperature Evidence: ledger:E1130</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31568" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x4CA" flags="0x0">
    <title>A/C Cut at Idle Droop - Engine Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The A/C compressor is cut when engine speed falls below this while the idle droop catch is active (engine speed well below desired idle, see Idle Airflow vs RPM Below Desired). Stock 450 rpm. Effect: raise = the compressor is cut earlier in an idle speed dip; lower = later Evidence: ledger:E0756, ledger:E1566</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x299B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4CB" flags="0x0">
    <title>A/C Cut at Idle Droop - Cut Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the A/C compressor stays cut after an idle droop cut starts (A/C Cut at Idle Droop - Engine Speed Limit). Stock 5.0 s. Effect: raise = the compressor stays off longer after an idle speed dip Evidence: ledger:E0756, ledger:E1566</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x299B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4CC" flags="0x0">
    <title>A/C Disable - System Voltage Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C compressor is cut when system voltage falls below this. Stock 9.5 V. Effect: raise = the compressor is cut at a higher voltage Evidence: ledger:E1007</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20432" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4CD" flags="0x0">
    <title>A/C Re-Enable - System Voltage Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a low voltage cut, the A/C compressor is allowed again once system voltage rises above this. Stock 10.0 V. Effect: raise = the compressor stays cut until voltage recovers further Evidence: ledger:E1007</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20434" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4CE" flags="0x0">
    <title>A/C Disable - System Voltage High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C compressor is cut when system voltage rises above this. Stock 16.0 V. Effect: lower = the compressor is cut at a lower voltage Evidence: ledger:E1007</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20436" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4CF" flags="0x0">
    <title>A/C Re-Enable - System Voltage High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a high voltage cut, the A/C compressor is allowed again once system voltage falls below this. Stock 15.8 V. Effect: lower = the compressor stays cut until voltage drops further Evidence: ledger:E1007</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20438" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4D0" flags="0x0">
    <title>A/C Engage While Cranking - Minimum Refrigerant Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The A/C compressor is engaged during engine cranking only when refrigerant pressure is at or above this (with the other cranking conditions met). Stock 150 kPa. Effect: raise = the compressor engages during cranking less often Evidence: ledger:E0756, ledger:E1568</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2043A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4D1" flags="0x0">
    <title>A/C Engage While Cranking - Minimum System Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. System voltage must be at or above this for the A/C compressor to engage during cranking. Stock 8.5 V. Effect: raise = no compressor engagement on a weaker cranking voltage Evidence: ledger:E0756, ledger:E1568</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2043C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4D2" flags="0x0">
    <title>A/C Engage While Cranking - Coolant Temperature Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The A/C compressor engages during cranking only while coolant temperature is below this. Stock 80 C. Effect: raise = cranking engagement also on a warmer engine; lower = only on a cooler engine Evidence: ledger:E0756, ledger:E1568</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2043E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4D3" flags="0x0">
    <title>A/C Engage While Cranking - Minimum Intake Air Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intake air temperature must be above this for the A/C compressor to engage during cranking. Stock 5 C. Effect: raise = no cranking engagement in cooler weather Evidence: ledger:E0298, ledger:E0756, ledger:E0815, ledger:E1568</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20440" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4D4" flags="0x0">
    <title>A/C Engage While Cranking - Maximum Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Longest time the A/C compressor stays engaged during one cranking event. It also ends as soon as the engine is running. Stock 3.5 s. Effect: raise = the compressor can stay engaged longer during a long crank Evidence: ledger:E0756, ledger:E1568</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20446" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4D5" flags="0x0">
    <title>A/C Disable - Refrigerant Pressure High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A/C compressor is cut when refrigerant pressure rises above this. Stock 3160 kPa (458 psi). Effect: lower = the compressor is cut at a lower pressure Evidence: ledger:E1008</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20448" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4D6" flags="0x0">
    <title>EVAP Test - Pull-Down Vacuum Target</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak test (P0455): tank vacuum the purge controller aims for while it pulls the sealed system down. Stock 9.5 inH2O. Effect: raise = the test pulls the tank to a deeper vacuum Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3739E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4D7" flags="0x0">
    <title>EVAP Test - Pull-Down Purge Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak test (P0455): least commanded purge during the pull-down. Stock 6 %. Effect: raise = purge never drops as low during the pull-down Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x373A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4D8" flags="0x0">
    <title>EVAP Test - Pull-Down Over-Vacuum Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak test (P0455): time above the pull-down vacuum maximum before purge is shut. Stock 0.8 s. Effect: raise = purge is shut later on over-vacuum Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x373A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4D9" flags="0x0">
    <title>EVAP Test - Pull-Down Vacuum Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. EVAP gross leak test (P0455): tank vacuum above which, after the over-vacuum time, purge is shut until vacuum falls back below the target. Stock 12 inH2O. Effect: raise = more vacuum is allowed before purge is shut Evidence: ledger:E1070</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37392" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4DA" flags="0x0">
    <title>Knock Detection - Transient Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: how long the transient state is kept after the last transient trigger (engine speed, throttle or airmass). Used in steps of 12.5 ms. Stock 0.25 s. Effect: raise = knock detection stays in its transient settings for longer after a transient Evidence: ledger:E1138</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31E10" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>32.767500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4DB" flags="0x0">
    <title>P2026 Test Enable - Coolant Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel vapor temperature sensor circuit low test (P2026) runs only while coolant is below this. Stock -30 C. P2026 is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0756, ledger:E1186</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37A7C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC (ECT)</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4DC" flags="0x0">
    <title>P2026 Test Enable - Minimum Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel vapor temperature sensor circuit low test (P2026) runs only after the engine has run longer than this. Stock 10 s. P2026 is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0756, ledger:E0811, ledger:E1186</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37A7E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4DD" flags="0x0">
    <title>P2026 Test Enable - Intake Air Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel vapor temperature sensor circuit low test (P2026) runs only while intake air temperature is at or below this. Stock 50 C. P2026 is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0756, ledger:E1186</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37A80" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC (IAT)</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4DE" flags="0x0">
    <title>P2026 Test Enable - Minimum Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel vapor temperature sensor circuit low test (P2026) runs only at or above this vehicle speed. Stock 25 km/h. P2026 is switched off in this calibration: dormant, no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0756, ledger:E1186</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37A82" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x4DF" flags="0x30">
    <title>Idle Throttle Area - Air Temperature Term</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Physical term of the idle throttle area calculation: square root of (287 x intake air temperature in kelvin), by intake air temperature (-40 to 152 C). Stock 259 to 349. It is the gas law, not a tuning value, and two other routines share it: leave it as it is. Effect: raise = more throttle area for the same idle airflow at that air temperature Evidence: ledger:E1106</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC intake air</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A13A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>m/s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E0" flags="0x30">
    <title>Idle Throttle Area - Flow Function vs Pressure Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Physical term of the idle throttle area calculation: the nozzle flow function, by manifold pressure divided by barometric pressure (0 to 1). Stock 0.685 up to a ratio of 0.5 (sonic flow), falling to 0.465 at 0.875 and held there. It is physics, not a tuning value, and another routine shares it. Effect: lower = more throttle area for the same idle airflow at that pressure ratio Evidence: ledger:E1106</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>MAP / baro</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.062" />
      <LABEL index="2" value="0.125" />
      <LABEL index="3" value="0.188" />
      <LABEL index="4" value="0.25" />
      <LABEL index="5" value="0.312" />
      <LABEL index="6" value="0.375" />
      <LABEL index="7" value="0.438" />
      <LABEL index="8" value="0.5" />
      <LABEL index="9" value="0.562" />
      <LABEL index="10" value="0.625" />
      <LABEL index="11" value="0.688" />
      <LABEL index="12" value="0.75" />
      <LABEL index="13" value="0.812" />
      <LABEL index="14" value="0.875" />
      <LABEL index="15" value="0.938" />
      <LABEL index="16" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A15E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E1" flags="0x30">
    <title>Cold Start High Idle - Minimum Time vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold start high idle: shortest time the high idle stays on, by coolant temperature at start (-40 to 152 C). After it the high idle ends once the truck moves faster than the request hold speed; it also ends when coolant reaches the end temperature. Stock 1800 / 1200 / 600 s at -40 / -28 / -16 C and 0 from -4 C. Effect: raise = the cold start high idle lasts longer Evidence: ledger:E1112</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC startup coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B104" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E2" flags="0x30">
    <title>Idle Airflow RPM Adder - Time After Power Enrichment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: how long after power enrichment ends the rpm airflow adder stays switched in, by engine speed (rows, 0 to 4096 rpm) and by how long the enrichment lasted (columns, 16 / 144 / 272 s). Stock 0 to 12 s. Effect: raise = the rpm adder stays in longer after coming off power Evidence: ledger:E1105, ledger:E1329</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>s power enrichment lasted</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="16" />
      <LABEL index="1" value="144" />
      <LABEL index="2" value="272" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1024" />
      <LABEL index="2" value="2048" />
      <LABEL index="3" value="3072" />
      <LABEL index="4" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A086" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E3" flags="0x30">
    <title>Idle Predicted Airflow Floor - Speed Minimum by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: the predicted airflow floor (see the floor curve by rpm) applies only above this vehicle speed, one value per transmission state. Stock 200 km/h in every state, so the floor never applies. Effect: lower = the floor applies above that speed in that gear Evidence: ledger:E1110</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>transmission state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="not used" />
      <LABEL index="5" value="not used" />
      <LABEL index="6" value="Neutral" />
      <LABEL index="7" value="Reverse" />
      <LABEL index="8" value="Park" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29DD0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4E4" flags="0x30">
    <title>Idle Predicted Airflow - Floor vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow control: lowest value of the predicted idle airflow, by engine speed (400 to 3600 rpm). It applies only above the per gear speed gate, which stock sets to 200 km/h in every gear, so on stock this floor never applies. Effect: raise = higher minimum predicted airflow (only once the speed gate is lowered) Evidence: ledger:E1105</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29E96" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x4E5" flags="0x0">
    <title>Idle Altitude Up - Coolant Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The altitude idle-up applies only while engine coolant is below this. Stock -256 C: never. Altitude idle-up: at low barometric pressure (below Idle Altitude Up Baro) with coolant below the limit, desired idle is raised by the altitude adder. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0757, ledger:E1508</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B0A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4E6" flags="0x0">
    <title>Cold Start High Idle - End Coolant Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold start high idle: the high idle ends when coolant reaches this. Stock 68 C. Effect: lower = the cold start high idle ends sooner Evidence: ledger:E1112</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B0A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4E7" flags="0x0">
    <title>Cold Start High Idle - Arming Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cold start high idle: it is armed at start only when startup coolant and intake air temperature are both at or below this. Stock -8 C. Effect: raise = the cold start high idle is also used on milder starts Evidence: ledger:E1112</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B0AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4E8" flags="0x0">
    <title>Burst Knock Retard - Startup Decay Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During the first seconds after start (the startup decay window), the burst knock retard is multiplied by this every update. Stock 0.5, so it halves each update. Effect: raise = burst knock retard fades more slowly after start Evidence: ledger:E0759</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2BACE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4E9" flags="0x0">
    <title>Burst Knock Retard - Startup Decay Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Run time after start during which the burst knock retard is scaled down every update by the startup decay factor. Stock 15 s. Effect: raise = the startup decay lasts longer Evidence: ledger:E0759</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2BAD0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4EA" flags="0x0">
    <title>O2 Sensor Tests Enable - Fuel Level Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensor response test and the O2 sensor voltage checks (P0131 / P0132 / P0137 / P0138) only run with fuel level at or above this, unless a fuel level sensor code (P0461 / P0462 / P0463) is active. Stock 10 %. Effect: lower = the tests also run with less fuel in the tank Evidence: ledger:E0993</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x361E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4EB" flags="0x0">
    <title>Transfer Case High Range Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the output speed sensor reading to get transmission output speed while the transfer case is in high range. The sensor sits after the transfer case, so this is the high-range ratio (1.00 on the stock transfer case). Stock 1.00. Change it only for a transfer case whose high range is not 1:1, together with Transfer Case Low Range Ratio. Effect: raise = transmission output speed, and so shift and converter lockup speeds, read higher in high range Evidence: ledger:E0761, ledger:E0808, ledger:E0810</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FB16" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>:1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4EC" flags="0x0">
    <title>First-Run Mode - Idle Base Spark</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First-run mode runs only during the first 12 s of engine running recorded by the PCM (kept through power-off), with a stored flag set, the mode enable set and start-up coolant inside the coolant window. During it the idle base spark is this fixed value instead of the Idle Base Spark table. Stock 16 deg. Effect: raise = more idle spark advance during first-run mode Evidence: ledger:E0763, ledger:E1227</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2F070" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x4ED" flags="0x30">
    <title>Idle Shift Kick Extended Term - Spark vs Turbine Speed Fall</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark advance added to the idle spark while the idle shift kick extended term is active, by how far the turbine speed rate is below the gear kick bias (0 to 2000 rpm/s). Stock 0. Dormant: the extended term is switched off in this calibration, so it has no effect on this truck&#x27;s software. Effect: raise = more idle spark advance from the shift kick extended term Evidence: ledger:E0763, ledger:E0936, ledger:E1234</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm/s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="125" />
      <LABEL index="2" value="250" />
      <LABEL index="3" value="375" />
      <LABEL index="4" value="500" />
      <LABEL index="5" value="625" />
      <LABEL index="6" value="750" />
      <LABEL index="7" value="875" />
      <LABEL index="8" value="1000" />
      <LABEL index="9" value="1125" />
      <LABEL index="10" value="1250" />
      <LABEL index="11" value="1375" />
      <LABEL index="12" value="1500" />
      <LABEL index="13" value="1625" />
      <LABEL index="14" value="1750" />
      <LABEL index="15" value="1875" />
      <LABEL index="16" value="2000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EA5C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4EE" flags="0x30">
    <title>Idle Spark Coolant Advance Multiplier vs Barometric Pressure</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the idle spark coolant advance (Park/Neutral and in gear) by barometric pressure. Stock 1.0 at every pressure, so it has no effect. Effect: lower = less idle coolant spark advance at that barometric pressure Evidence: ledger:E0763, ledger:E1220</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>kPa (baro)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EAAC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4EF" flags="0x30">
    <title>Idle Spark Coolant Advance (Park/Neutral)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark advance added to the idle spark in Park or Neutral, by coolant temperature, before the idle maximum and minimum are applied. Scaled by the barometric multiplier. Stock 12 deg cold falling to 2 deg warm. Effect: raise = more idle spark advance at that coolant temperature in Park or Neutral Evidence: ledger:E0763, ledger:E0936, ledger:E1220</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>degC (ECT)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EA80" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x4F0" flags="0x30">
    <title>Idle Spark Coolant Advance (In Gear)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark advance added to the idle spark in gear, by coolant temperature, before the idle maximum and minimum are applied. Scaled by the barometric multiplier. Stock 10 deg cold falling to 0 warm. Effect: raise = more idle spark advance at that coolant temperature in gear Evidence: ledger:E0763, ledger:E0936, ledger:E1220</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>degC (ECT)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EA96" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x4F1" flags="0x0">
    <title>Converter Model Alternate Estimate - Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new alternate estimate value taken into the filtered value; 0 = no smoothing. Stock 0.21. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0774, ledger:E1491</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FB7E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4F2" flags="0x0">
    <title>P0719 Test - Pull-Away Time Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: longest time from the low speed to the high speed that counts as a pull-away event. Stock 12.5 s. A pull-away event is: from the low speed up to the high speed inside the time window, then the hold time above the high speed. Effect: raise = slower pull-aways also count Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCCC" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4F3" flags="0x0">
    <title>P0719 Test - Pull-Away Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: shortest time from the low speed to the high speed that counts as a pull-away event. Stock 2.5 s. A pull-away event is: from the low speed up to the high speed inside the time window, then the hold time above the high speed. Effect: raise = quick pull-aways no longer count Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCCD" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4F4" flags="0x0">
    <title>P0719 Test - Time Above High Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: time the truck must stay at or above the high speed to complete a pull-away event. Stock 7 s. A pull-away event is: from the low speed up to the high speed inside the time window, then the hold time above the high speed. Effect: raise = each event needs longer at speed Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCCE" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4F5" flags="0x0">
    <title>P0719 Fail - Brake Input On Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: time the brake input must read on without a break before the code can set (together with the pull-away event count). Stock 900 s. Effect: raise = the input must stay on longer Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCD0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4F6" flags="0x0">
    <title>P0719 Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: time the brake input must read off to pass the check. Stock 2 s. Effect: raise = the check takes longer to pass Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCD2" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4F7" flags="0x0">
    <title>P0724 Test - Time Above High Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0724 (brake switch input stuck off) check: time the truck must stay at or above the high speed before a stop event can start. Stock 7 s. A stop event is: the hold time above the high speed, then down to the low speed inside the time window. Effect: raise = each event needs longer at speed first Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCD3" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4F8" flags="0x0">
    <title>P0724 Test - Stop Time Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0724 (brake switch input stuck off) check: longest time from the high speed down to the low speed that counts as a stop event. Stock 12.5 s. A stop event is: the hold time above the high speed, then down to the low speed inside the time window. Effect: raise = slower stops also count Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCD4" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4F9" flags="0x0">
    <title>P0724 Test - Stop Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0724 (brake switch input stuck off) check: shortest time from the high speed down to the low speed that counts as a stop event. Stock 2.5 s. A stop event is: the hold time above the high speed, then down to the low speed inside the time window. Effect: raise = quick stops no longer count Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCD5" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4FA" flags="0x0">
    <title>P0724 Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0724 (brake switch input stuck off) check: time the brake input must read on to pass the check. Stock 2 s. Effect: raise = the check takes longer to pass Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCD6" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4FB" flags="0x0">
    <title>P0719 Test - Pull-Away Low Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: a pull-away event starts from at or below this speed. Stock 8 km/h. A pull-away event is: from the low speed up to the high speed inside the time window, then the hold time above the high speed. Effect: raise = events can start from a higher speed Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCD8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4FC" flags="0x0">
    <title>P0719 Test - Pull-Away High Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: speed the truck must reach to end the acceleration part of a pull-away event. Stock 32 km/h. A pull-away event is: from the low speed up to the high speed inside the time window, then the hold time above the high speed. Effect: raise = events need a higher speed Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCDA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4FD" flags="0x0">
    <title>P0724 Test - Stop High Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0724 (brake switch input stuck off) check: a stop event starts from at or above this speed. Stock 32 km/h. A stop event is: the hold time above the high speed, then down to the low speed inside the time window. Effect: raise = events need a higher starting speed Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCDC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4FE" flags="0x0">
    <title>P0724 Test - Stop Low Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0724 (brake switch input stuck off) check: speed the truck must slow to, to complete a stop event. Stock 8 km/h. A stop event is: the hold time above the high speed, then down to the low speed inside the time window. Effect: raise = events complete at a higher speed Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCDE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x4FF" flags="0x0">
    <title>P0724 - Stops to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0724 (brake switch input stuck off) check: number of stop events with the brake input reading off all the time that sets the code. Stock 8. A stop event is: the hold time above the high speed, then down to the low speed inside the time window. Effect: raise = more stops are needed to set the code Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCE0" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x500" flags="0x0">
    <title>P0719 - Pull-Aways to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0719 (brake switch input stuck on) check: number of pull-away events with the brake input reading on all the time that is needed (with the on time) to set the code. Stock 8. A pull-away event is: from the low speed up to the high speed inside the time window, then the hold time above the high speed. Effect: raise = more pull-aways are needed to set the code Evidence: ledger:E1096</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCE1" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x501" flags="0x0">
    <title>P0503 Test - Arming Output Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): the check arms only after output speed has been above this. Stock 400 rpm. Effect: raise = the check arms at higher speed Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FD0A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x502" flags="0x0">
    <title>P0503 Test - Arming Time Above Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): time above the arming output speed before the check arms. Stock 2 s. Effect: raise = the check arms later Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FD14" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x503" flags="0x0">
    <title>P0503 Test - Arming Rise Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): a rise of output speed between two samples larger than this restarts the arming time. Stock 600 rpm. Effect: raise = larger speed jumps do not restart arming Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FD0C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x504" flags="0x0">
    <title>P0503 Test - Arming Time Without Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): time without a large rise of output speed before the check arms. Stock 2 s. Effect: raise = the check arms later Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FD16" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x505" flags="0x0">
    <title>P0502 Fail - Output Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): output speed at or below this, with the run conditions met, counts as no signal. Stock 100 rpm. Effect: lower = a lower reading is needed to count as no signal Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCEC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x506" flags="0x0">
    <title>P0502 Pass - Output Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): output speed at or above which the pass time runs. Stock 250 rpm. Effect: raise = the check needs a higher speed to pass Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCEE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x507" flags="0x0">
    <title>P0502 Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): time at or above the pass speed that passes the check. Stock 1.5 s. Effect: raise = the check takes longer to pass Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCF0" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x508" flags="0x0">
    <title>P0502 Fail - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): time with no signal under the run conditions that sets the code. Stock 4.5 s. Effect: raise = the signal must be missing longer Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCF1" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x509" flags="0x0">
    <title>P0502 Test - Run Condition, Engine Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): highest engine speed at which the check runs. Stock 5000 rpm. Effect: lower = the check stops at lower engine speed Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCF2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x50A" flags="0x0">
    <title>P0502 Test - Run Condition, Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): lowest engine speed at which the check runs. Stock 2850 rpm. Effect: lower = the check also runs at lower engine speed Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCF4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x50B" flags="0x0">
    <title>P0502 Test - Run Condition, Throttle Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): lowest driver throttle at which the check runs. Stock 10 %. Effect: raise = the check needs more throttle Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCF6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x50C" flags="0x0">
    <title>P0502 Test - Run Condition, Converter Slip Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): lowest torque converter slip at which the check runs. Stock -0.125 rpm: the check is off while slip is negative (it is a limit, not an off value). Effect: raise = the check needs positive converter slip Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FCFA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x50D" flags="0x0">
    <title>P0502 Test - Run Condition, Fluid Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0502 (output speed sensor no signal): lowest transmission fluid temperature at which the check runs. Stock just below 0 C (a limit, not an off value). Effect: raise = the check needs warmer fluid Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FD00" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x50E" flags="0x0">
    <title>P0503 Pass - Output Speed Drop Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): largest drop of output speed between two 25 ms samples that still counts as good for the pass time. Stock 500 rpm. Effect: raise = larger drops still count as good Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FD04" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x50F" flags="0x0">
    <title>P0503 Pass - Output Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): output speed at or above which the pass time runs. Stock 500 rpm. Effect: raise = the check passes only at higher speed Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FD08" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x510" flags="0x0">
    <title>P0503 Pass - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): time of good signal that passes the check. Stock 2 s. Effect: raise = the check takes longer to pass Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FD10" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x511" flags="0x0">
    <title>P0503 Fail - Output Speed Drop</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): a drop of output speed between two 25 ms samples of at least this starts the fault timer. Stock 350 rpm. Effect: raise = a larger sudden drop is needed to start the fault timer Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FD06" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x512" flags="0x0">
    <title>P0503 Fail - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): time the signal must stay down after a sudden drop to set the code. Stock 3.25 s. Effect: raise = the signal must stay down longer Evidence: ledger:E1094</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FD12" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x513" flags="0x0">
    <title>Output Speed Sensor - Timer Scale (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Scale of the pulse timer in the output speed calculation: the output speed reading is proportional to it. Stock 1.0. Part of how the PCM turns the output shaft speed sensor&#x27;s pulse count and pulse timer into output speed (the same calculation as the input speed sensor). Structural: DO NOT EDIT. Effect: DO NOT EDIT: changes every output speed reading Evidence: ledger:E0787, ledger:E1537</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FB2E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x514" flags="0x0">
    <title>Output Speed Sensor - Pulse Timer Rollover Correction (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Timer counts taken off the pulse time change when the pulse timer rolls over. Stock 0 (the timer rolls over at its full 16-bit range). Part of how the PCM turns the output shaft speed sensor&#x27;s pulse count and pulse timer into output speed (the same calculation as the input speed sensor). Structural: DO NOT EDIT. Effect: DO NOT EDIT: changes every output speed reading Evidence: ledger:E0787, ledger:E1537</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FB30" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x515" flags="0x0">
    <title>Output Speed Sensor - Pulse Count Rollover Correction (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pulses taken off the pulse count change when the pulse counter rolls over. Stock 0 (the counter rolls over at its full 16-bit range). Part of how the PCM turns the output shaft speed sensor&#x27;s pulse count and pulse timer into output speed (the same calculation as the input speed sensor). Structural: DO NOT EDIT. Effect: DO NOT EDIT: changes every output speed reading Evidence: ledger:E0787, ledger:E1537</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FB32" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>pulses</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x516" flags="0x0">
    <title>Knock Tables - RPM Axis Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at the first column of the knock detection tables. Stock 0 rpm. Both knock tables that use this axis move with it: the knock detection threshold gains (one per cylinder) and the knock window angle term. Their rows or columns are spread evenly between the start and end values, so changing either end re-spaces every breakpoint; re-check those tables after an edit. Effect: raise = the knock tables start their first column at a higher rpm Evidence: ledger:E0364, ledger:E0831</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31DAA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x517" flags="0x0">
    <title>Knock Tables - RPM Axis End</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at the last column of the knock detection tables; above it the last column is used. Stock 8000 rpm. Both knock tables that use this axis move with it: the knock detection threshold gains (one per cylinder) and the knock window angle term. Their rows or columns are spread evenly between the start and end values, so changing either end re-spaces every breakpoint; re-check those tables after an edit. Effect: raise = the knock tables cover a higher rpm range Evidence: ledger:E0364, ledger:E0831</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31DAC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x518" flags="0x0">
    <title>Knock Tables - Cylinder Airmass Axis Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cylinder airmass at the first row of the knock detection tables. Stock 0.24 g. Both knock tables that use this axis move with it: the knock detection threshold gains (one per cylinder) and the knock window angle term. Their rows or columns are spread evenly between the start and end values, so changing either end re-spaces every breakpoint; re-check those tables after an edit. Effect: raise = the knock tables start their first row at a higher load Evidence: ledger:E0364, ledger:E0831</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31DD0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/cyl</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.095937</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x519" flags="0x0">
    <title>Knock Tables - Cylinder Airmass Axis End</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cylinder airmass at the last row of the knock detection tables; above it the last row is used. Stock 0.72 g. This is the one engine load axis on this calibration that can be widened for boost: the spark, torque and fuel tables have fixed load ranges. Both knock tables that use this axis move with it: the knock detection threshold gains (one per cylinder) and the knock window angle term. Their rows or columns are spread evenly between the start and end values, so changing either end re-spaces every breakpoint; re-check those tables after an edit. Effect: raise = the knock tables cover higher cylinder loads (boost) Evidence: le...</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31DD2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/cyl</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.095937</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x51A" flags="0x0">
    <title>Knock Threshold EQ Factor - EQ Axis Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded fuel equivalence ratio at the first point of the knock threshold EQ factor curve. Stock 1.00. The curve&#x27;s points are spread evenly between the start and end values. Effect: raise = the EQ factor curve starts at a richer mixture Evidence: ledger:E0364, ledger:E0831</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31DE6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x51B" flags="0x0">
    <title>Knock Threshold EQ Factor - EQ Axis End</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded fuel equivalence ratio at the last point of the knock threshold EQ factor curve; richer than this uses the last point. Stock 1.90. The curve&#x27;s points are spread evenly between the start and end values. Effect: raise = the EQ factor curve covers richer mixtures Evidence: ledger:E0364, ledger:E0831</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x31DE8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>EQ</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x51C" flags="0x0">
    <title>Over-Temp Enrichment - Entry Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Coolant at or above which the enrichment may start. Stock 119 C. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26E44" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x51D" flags="0x0">
    <title>Over-Temp Enrichment - Hold Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Once active, the enrichment stays on while coolant is at or above this. Stock 115 C. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26E46" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x51E" flags="0x0">
    <title>Over-Temp Enrichment - Entry Coolant (Status Bit Set)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Entry coolant used instead while bit 0 of the first diagnostic status byte is set. Stock 126 C. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26E48" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x51F" flags="0x0">
    <title>Over-Temp Enrichment - Hold Coolant (Status Bit Set)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Hold coolant used instead while bit 0 of the first diagnostic status byte is set. Stock 122 C. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26E4A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x520" flags="0x0">
    <title>Over-Temp Enrichment - Entry Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Throttle at or above which the enrichment may start. Stock 50 %. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26E4C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x521" flags="0x0">
    <title>Over-Temp Enrichment - Hold Throttle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Once active, throttle must stay at or above this. Stock 45 %. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26E4E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x522" flags="0x0">
    <title>Over-Temp Enrichment - Entry MAP</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Manifold pressure at or above which the enrichment may start. Stock 55 kPa. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26E50" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x523" flags="0x0">
    <title>Over-Temp Enrichment - Hold MAP</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Once active, manifold pressure must stay at or above this. Stock 50 kPa. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26E52" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x524" flags="0x0">
    <title>Over-Temp Enrichment - Entry Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Vehicle speed at or above which the enrichment may start. Stock 20 km/h. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26E54" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x525" flags="0x0">
    <title>Over-Temp Enrichment - Hold Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant over-temperature enrichment (engine protection, keep stock). Once active, vehicle speed must stay at or above this. Stock 15 km/h. DO NOT TUNE (E0832). Whether it runs is set by these entry and hold gates. How much it adds comes from the start coolant, gain and cap items. Effect: engine protection; keep stock Evidence: ledger:E0249, ledger:E0832</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26E56" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x526" flags="0x0">
    <title>Tip-In Torque Ramp - Fast Step Slip Trigger</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. The fast step also starts once gearbox slip exceeds this. Stock 50 rpm. Effect: tip-in torque management Evidence: ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2104C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x527" flags="0x0">
    <title>Tip-In Torque Ramp - Lash Step Slip Trigger</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only): after a closed-throttle tip-in the torque limit ramps up (default, lash and fast steps). The fast step starts once the limit passes its target, once gearbox slip is large, or once the driveline has shunted forward, swung back and started climbing again. The lash step is used while gearbox slip exceeds this. Stock 10 rpm. Effect: tip-in torque management Evidence: ledger:E0845, ledger:E0846</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21046" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x528" flags="0x0">
    <title>Tip-In Arming - Slip Threshold B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tip-in torque management (H3 only) can only arm while the engine is turning less than a set amount faster than the transmission output implies in the current gear (torque converter plus gearbox slip). Below Threshold A it can arm; from Threshold A up to Threshold B it can arm only while engine torque is below the arm torque; at or above Threshold B it cannot arm. Once armed at closed throttle, opening the throttle starts the tip-in torque ramp. Stock both 250 rpm, so there is no in-between band. This is Threshold B. Effect: raise above Threshold A = opens a band where arming depends on engine torque Evidence: ledger:E0356, le...</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x21048" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x529" flags="0x0">
    <title>VE Transient Mode - RPM Band Split</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow source switching: the PCM normally uses the MAF airflow and, during a manifold pressure transient, switches to the VE (speed density) airflow times a learned MAF to VE ratio. It switches over when MAP keeps moving by more than the MAP change threshold per update (two updates in a row), or when MAP moves more than that over two updates while the throttle area moves the same way by more than the area change threshold; it switches back once the MAP change over one, two and three updates is at or below the MAP change threshold. The high band thresholds apply at or above the MAP split or the RPM split. At or above this eng...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C982" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x52A" flags="0x0">
    <title>VE Transient Mode - MAP Change Threshold (Low Band)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow source switching: the PCM normally uses the MAF airflow and, during a manifold pressure transient, switches to the VE (speed density) airflow times a learned MAF to VE ratio. It switches over when MAP keeps moving by more than the MAP change threshold per update (two updates in a row), or when MAP moves more than that over two updates while the throttle area moves the same way by more than the area change threshold; it switches back once the MAP change over one, two and three updates is at or below the MAP change threshold. The high band thresholds apply at or above the MAP split or the RPM split. MAP change per updat...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C984" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x52B" flags="0x0">
    <title>VE Transient Mode - MAP Change Threshold (High Band)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow source switching: the PCM normally uses the MAF airflow and, during a manifold pressure transient, switches to the VE (speed density) airflow times a learned MAF to VE ratio. It switches over when MAP keeps moving by more than the MAP change threshold per update (two updates in a row), or when MAP moves more than that over two updates while the throttle area moves the same way by more than the area change threshold; it switches back once the MAP change over one, two and three updates is at or below the MAP change threshold. The high band thresholds apply at or above the MAP split or the RPM split. MAP change per updat...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C986" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x52C" flags="0x0">
    <title>VE Transient Mode - Throttle Area Change Threshold (Low Band)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow source switching: the PCM normally uses the MAF airflow and, during a manifold pressure transient, switches to the VE (speed density) airflow times a learned MAF to VE ratio. It switches over when MAP keeps moving by more than the MAP change threshold per update (two updates in a row), or when MAP moves more than that over two updates while the throttle area moves the same way by more than the area change threshold; it switches back once the MAP change over one, two and three updates is at or below the MAP change threshold. The high band thresholds apply at or above the MAP split or the RPM split. Throttle area change...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C988" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>399.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x52D" flags="0x0">
    <title>VE Transient Mode - Throttle Area Change Threshold (High Band)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow source switching: the PCM normally uses the MAF airflow and, during a manifold pressure transient, switches to the VE (speed density) airflow times a learned MAF to VE ratio. It switches over when MAP keeps moving by more than the MAP change threshold per update (two updates in a row), or when MAP moves more than that over two updates while the throttle area moves the same way by more than the area change threshold; it switches back once the MAP change over one, two and three updates is at or below the MAP change threshold. The high band thresholds apply at or above the MAP split or the RPM split. Throttle area change...</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C98A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>399.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x52E" flags="0x0">
    <title>Engine Displacement</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM turns cylinder airmass into engine load by dividing it by the ideal charge of one cylinder (at barometric pressure, and at 105 kPa and -40 C), worked out from this displacement for 5 cylinders. It also sets the cranking airmass (cranking VE x MAP x cylinder volume / charge temperature). Set this to the engine&#x27;s real displacement after a bore or stroke change. Stock 3.5 L. The PCM cannot represent more than about 5.8 L here. Effect: raise = the same airmass reads as a lower engine load Evidence: ledger:E0217, ledger:E0860, ledger:E0861</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2BD96" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>L</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>9.999847</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/6553.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x52F" flags="0x0">
    <title>Ideal Cylinder Charge Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM turns cylinder airmass into engine load by dividing it by the ideal charge of one cylinder (at barometric pressure, and at 105 kPa and -40 C), worked out from this displacement for 5 cylinders. This multiplies the ideal charge worked out from the displacement. Stock 1.0. Effect: raise = the same airmass reads as a lower engine load Evidence: ledger:E0217, ledger:E0860</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2BD98" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x530" flags="0x0">
    <title>Airmass Predictor MAP Band Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airmass predictor region: the PCM predicts cylinder airmass a little ahead of the MAF reading, with a separate set of predictor coefficients per region. The region is an idle window (low throttle, low engine speed, moderate vacuum) or one of 16 cells from four engine speed bands by four MAP bands. Leave these at stock unless the predictor coefficients are recalibrated with them. MAP hysteresis: the region keeps its MAP band until MAP moves this far past either band edge (every MAP band). Stock 1 kPa. Effect: raise = the predictor region changes MAP band less often Evidence: ledger:E0323, ledger:E0864, ledger:E0891</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2CA12" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x531" flags="0x0">
    <title>Airmass Predictor Idle Region - Throttle Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airmass predictor region: the PCM predicts cylinder airmass a little ahead of the MAF reading, with a separate set of predictor coefficients per region. The region is an idle window (low throttle, low engine speed, moderate vacuum) or one of 16 cells from four engine speed bands by four MAP bands. Leave these at stock unless the predictor coefficients are recalibrated with them. The idle region needs throttle below this. Stock 5 %. Effect: moves which predictor coefficient set applies Evidence: ledger:E0323, ledger:E0864</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2CA14" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x532" flags="0x0">
    <title>Airmass Predictor Idle Region - Engine Speed Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airmass predictor region: the PCM predicts cylinder airmass a little ahead of the MAF reading, with a separate set of predictor coefficients per region. The region is an idle window (low throttle, low engine speed, moderate vacuum) or one of 16 cells from four engine speed bands by four MAP bands. Leave these at stock unless the predictor coefficients are recalibrated with them. The idle region needs engine speed below this. Stock 1000 rpm. Effect: moves which predictor coefficient set applies Evidence: ledger:E0323, ledger:E0864</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2CA16" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x533" flags="0x0">
    <title>Burst Knock Retard Multiplier - Step Down</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Burst knock retard learned multiplier: two learned multipliers (1.0 = full burst retard) scale the burst knock retard. One event raises the active multiplier by the step up, another lowers it by the step down, and it is never allowed below the floor. Stock floor is 1.0, the top of the range, so on the stock calibration the multipliers stay at 1.0 and nothing is learned; lowering the floor lets burst retard learn down. This is the step down. Stock 0.03. Effect: raise = the multiplier falls faster (only below a lowered floor) Evidence: ledger:E0869</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2B92E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x534" flags="0x0">
    <title>Burst Knock Retard Multiplier - Reset Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Burst knock retard learned multiplier: two learned multipliers (1.0 = full burst retard) scale the burst knock retard. One event raises the active multiplier by the step up, another lowers it by the step down, and it is never allowed below the floor. Stock floor is 1.0, the top of the range, so on the stock calibration the multipliers stay at 1.0 and nothing is learned; lowering the floor lets burst retard learn down. Value both multipliers are set to after a fault reset. Stock 1.0. Effect: sets where learning restarts after a reset Evidence: ledger:E0869</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2B934" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>x</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x535" flags="0x0">
    <title>Burst Knock Retard - Hold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Burst knock retard sequence: a quick rise in cylinder airmass starts a burst of spark retard (sized by the burst retard curves and the learned multiplier). After the delay the retard is applied, held for the hold count, then removed in equal steps over the decay count. Counts are updates of the burst retard routine. This is how long the full retard is held. Stock 5 updates. Effect: raise = full burst retard is held longer Evidence: ledger:E0870</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2B912" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x536" flags="0x0">
    <title>Burst Knock Retard - Decay Steps</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Burst knock retard sequence: a quick rise in cylinder airmass starts a burst of spark retard (sized by the burst retard curves and the learned multiplier). After the delay the retard is applied, held for the hold count, then removed in equal steps over the decay count. Counts are updates of the burst retard routine. This is the number of equal steps the retard is removed over. Stock 10 updates. Effect: raise = the burst retard fades out more slowly Evidence: ledger:E0870</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2B914" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x537" flags="0x0">
    <title>Knock Learn Rate - Engine Speed Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is one of the five weights (relative; only the ratios matter). Stock 0.004. Effect: raise = this curve counts for more in the average Evidence: ledger:E0193, ledger:E0871</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2BAC2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x538" flags="0x0">
    <title>Knock Learn Rate - Coolant Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is one of the five weights (relative; only the ratios matter). Stock 1.0. Effect: raise = this curve counts for more in the average Evidence: ledger:E0193, ledger:E0871</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2BAC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x539" flags="0x0">
    <title>Knock Learn Rate - Intake Temperature Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is one of the five weights (relative; only the ratios matter). Stock 0.5. Effect: raise = this curve counts for more in the average Evidence: ledger:E0193, ledger:E0871</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2BAC6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x53A" flags="0x0">
    <title>Knock Learn Rate - Sample Count Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock learning rate for under-sampled cylinders: when a cylinder has had too few knock-learning samples, its learning rate factor is the weighted average of five curves (manifold pressure, engine speed, sample count, coolant and intake temperature), each a fraction from 0 to 1, weighted by the five weights. This is one of the five weights (relative; only the ratios matter). Stock 0.125. Effect: raise = this curve counts for more in the average Evidence: ledger:E0193, ledger:E0871</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2BAC8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x53B" flags="0x30">
    <title>O2 Response Test - Reversal Tolerance, Lean to Rich</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A drop larger than this during a lean-to-rich transition discards that transition. Stock 5 mV. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: changes what the O2 response test measures Evidence: ledger:E0281, ledger:E0295, ledger:E0902</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (bank 1)" />
      <LABEL index="1" value="second sensor (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3670A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x53C" flags="0x30">
    <title>O2 Response Test - Reversal Tolerance, Rich to Lean</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A rise larger than this during a rich-to-lean transition discards that transition. Stock 5 mV. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: changes what the O2 response test measures Evidence: ledger:E0281, ledger:E0295, ledger:E0902</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (bank 1)" />
      <LABEL index="1" value="second sensor (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3670E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x53D" flags="0x30">
    <title>O2 Response Test - Transition Timing Low Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower end of the transition timing window (transitions are timed between this and the high voltage). Stock 350 mV. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: changes what the O2 response test measures Evidence: ledger:E0281, ledger:E0295, ledger:E0902</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (bank 1)" />
      <LABEL index="1" value="second sensor (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36712" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x53E" flags="0x30">
    <title>O2 Response Test - Transition Timing High Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper end of the transition timing window. Stock 650 mV. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: changes what the O2 response test measures Evidence: ledger:E0281, ledger:E0295, ledger:E0902</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (bank 1)" />
      <LABEL index="1" value="second sensor (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36716" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x53F" flags="0x30">
    <title>O2 Response Test - Lean Switch Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Falling to this or below counts a lean switch. Stock 500 mV. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: changes what the O2 response test measures Evidence: ledger:E0281, ledger:E0295, ledger:E0902</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (bank 1)" />
      <LABEL index="1" value="second sensor (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3671A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x540" flags="0x30">
    <title>O2 Response Test - Rich Switch Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rising to this or above counts a rich switch. Stock 600 mV. The O2 response test watches the front O2 sensor in steady closed-loop cruise, times each lean-to-rich and rich-to-lean swing between 350 and 650 mV and counts crossings of 600 mV (rising) and 500 mV (falling). Limits are looked up by the average airflow over the test (stock values are the same at every airflow). Effect: changes what the O2 response test measures Evidence: ledger:E0281, ledger:E0295, ledger:E0902</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (bank 1)" />
      <LABEL index="1" value="second sensor (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3671E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x541" flags="0x0">
    <title>P0562 Test - Run Condition, Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0562 test only runs while engine speed is at or above this. Stock 1200 rpm. Effect: raise = the test needs a higher engine speed to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x204A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x542" flags="0x0">
    <title>P0068 Test - Run Condition, Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0068 test only runs while engine speed is above this. Stock 800 rpm. Effect: raise = the test needs a higher engine speed to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DA6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x543" flags="0x0">
    <title>P0325 Test - Run Condition, Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0325 test only runs while engine speed is above this. Stock 1800 rpm. Effect: raise = the test needs a higher engine speed to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32752" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x544" flags="0x0">
    <title>P0325 Test - Run Condition, Engine Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0325 test only runs while engine speed is below this. Stock 6400 rpm. Effect: lower = the test needs a lower engine speed to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32754" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x545" flags="0x0">
    <title>P0327 / P0332 Test - Run Condition, Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0327 / P0332 test only runs while engine speed is above this. Stock 1800 rpm. Effect: raise = the test needs a higher engine speed to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x32756" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x546" flags="0x0">
    <title>P0116 Test - Startup Coolant Pass Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or below this startup coolant temperature the P0116 test reports a pass at once and skips its warm-up checks (the startup coolant high limit is still checked first). Above it the warm-up checks run. Stock 15 degC. Effect: raise = more cold starts pass P0116 without the warm-up checks Evidence: ledger:E0906, ledger:E0912</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3514C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x547" flags="0x0">
    <title>P0522 / P0523 Test - Run Condition, System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0522 / P0523 test only runs while system voltage is at or above this. Stock 11 V. Effect: raise = the test needs a higher system voltage to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36188" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x548" flags="0x0">
    <title>P0326 Test - Run Condition, Manifold Pressure Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P0326 test only runs while manifold pressure is at or above this. Stock 55 kPa. Effect: raise = the test needs a higher manifold pressure to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38692" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x549" flags="0x0">
    <title>P1380 / P1381 Test - Run Condition, Vehicle Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The P1380 / P1381 test only runs while vehicle speed is at or above this. Stock 5 km/h. Effect: raise = the test needs a higher vehicle speed to run Evidence: ledger:E0906</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A7A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x54A" flags="0x0">
    <title>P0563 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0563 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 6. Effect: raise = P0563 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x204A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x54B" flags="0x0">
    <title>P0562 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0562 sets once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 6. Effect: raise = P0562 needs more samples before it sets Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x204AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x54C" flags="0x0">
    <title>P0562 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0562 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 6. Effect: raise = P0562 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x204AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x54D" flags="0x0">
    <title>P0117 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0117 reports a pass once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 100. Effect: raise = P0117 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35226" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x54E" flags="0x0">
    <title>P1114 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1114 reports a pass once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 2000. Effect: raise = P1114 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35228" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x54F" flags="0x0">
    <title>P0118 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0118 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 100. Effect: raise = P0118 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35232" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x550" flags="0x0">
    <title>P1115 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P1115 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 2000. Effect: raise = P1115 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35234" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x551" flags="0x0">
    <title>P0442 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0442 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 6. Effect: raise = P0442 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35756" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x552" flags="0x0">
    <title>P0451 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0451 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 6. Effect: raise = P0451 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35762" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x553" flags="0x0">
    <title>P0453 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0453 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 100. Effect: raise = P0453 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37338" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x554" flags="0x0">
    <title>P0452 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0452 sets once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 80. Effect: raise = P0452 needs more samples before it sets Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3733A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x555" flags="0x0">
    <title>P0452 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0452 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 100. Effect: raise = P0452 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3733C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x556" flags="0x0">
    <title>P2027 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2027 reports a pass once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 100. Effect: raise = P2027 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37A64" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x557" flags="0x0">
    <title>P2026 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2026 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 100. Effect: raise = P2026 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37A68" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x558" flags="0x0">
    <title>P0326 Pass - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0326 reports a pass once this count is reached. The count goes up by one each time the test runs. Stock 80. Effect: raise = P0326 needs more samples before it passes Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3868E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x559" flags="0x0">
    <title>P2610 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2610 sets once this count is reached. The count goes up by one each time the test runs. Stock 3. Effect: raise = P2610 needs more samples before it sets Evidence: ledger:E0907</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A4A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x55A" flags="0x0">
    <title>P0563 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0563 sets once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 6. Effect: raise = P0563 needs more samples before it sets Evidence: ledger:E0909</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x204A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x55B" flags="0x0">
    <title>P0520 Fail - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0520 sets once its fault has been present for this long. Stock 5 s. Effect: raise = the fault must last longer before P0520 sets Evidence: ledger:E0909, ledger:E1041</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36186" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x55C" flags="0x0">
    <title>P0453 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0453 sets once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 80. Effect: raise = P0453 needs more samples before it sets Evidence: ledger:E0909</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37336" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x55D" flags="0x0">
    <title>P0326 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0326 sets once this count is reached. The count goes up by one each time the test runs with its condition met. Stock 40. Effect: raise = P0326 needs more samples before it sets Evidence: ledger:E0909</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3868C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x55E" flags="0x0">
    <title>P0622 Fail - Time, Engine Stopped</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0622 (generator field control circuit) key-on, engine-stopped check: P0622 sets once the check has run with engine speed at 0 and the field signal at or below its limit for this long. Stock 5 s. Effect: raise = the engine-stopped check takes longer to set P0622 Evidence: ledger:E0913, ledger:E0958</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x203D4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x55F" flags="0x0">
    <title>P0622 Fail - Time, Engine Running</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0622 (generator field control circuit) engine-running check: P0622 sets once the check has run with the engine running and the field signal at or above its limit for this long. Stock 30 s. Effect: raise = the engine-running check takes longer to set P0622 Evidence: ledger:E0913, ledger:E0958</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x203D6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x560" flags="0x0">
    <title>Fuel Trim Monitor Enable - Coolant Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while coolant temperature is above this. Stock -35 C. Narrowing the window makes the monitor run less often. Effect: raise = the monitor needs a warmer engine to run Evidence: ledger:E0971</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DD4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x561" flags="0x0">
    <title>Fuel Trim Monitor Enable - Coolant Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while coolant temperature is below this. Stock 125 C. Narrowing the window makes the monitor run less often. Effect: lower = the monitor stops at a lower coolant temperature Evidence: ledger:E0971</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DD2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x562" flags="0x0">
    <title>Fuel Trim Monitor Enable - Airflow Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while mass airflow is above this. Stock 1 g/s. Narrowing the window makes the monitor run less often. Effect: raise = the monitor needs more airflow to run Evidence: ledger:E0971</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D98" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x563" flags="0x0">
    <title>Fuel Trim Monitor Enable - Intake Air Temperature Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while intake air temperature is below this. Stock 145 C (no limit in practice). Narrowing the window makes the monitor run less often. Effect: lower = the monitor stops at a lower intake air temperature Evidence: ledger:E0971</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DE4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x564" flags="0x0">
    <title>Fuel Trim Monitor Enable - Vehicle Speed Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel trim monitor (P0171 system too lean, P0172 system too rich) only runs its checks while vehicle speed is below this. Stock 132 km/h. Narrowing the window makes the monitor run less often. Effect: lower = the monitor stops at a lower speed Evidence: ledger:E0971</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37DFA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x565" flags="0x0">
    <title>Fuel Trim Monitor Stage Enable - Airflow Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. One of the fuel trim monitor&#x27;s (P0171 system too lean, P0172 system too rich) conditions for running its test stages: mass airflow must be above this. Stock 2 g/s. Narrowing the window makes the monitor run less often. Effect: raise = the monitor&#x27;s stages need more airflow to run Evidence: ledger:E0971</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D9C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x566" flags="0x0">
    <title>Transmission Diagnostics Enable - Engine Speed Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most transmission diagnostics (fluid temperature sensor, turbine speed, pressure switch, TCC and gear ratio tests) only run once engine speed has stayed at or above this (and at or below the high limit) for the engine run time below. Stock 450 rpm. Effect: raise = transmission diagnostics need a higher engine speed to run Evidence: ledger:E0976</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FD28" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x567" flags="0x0">
    <title>Transmission Diagnostics Enable - Engine Speed High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most transmission diagnostics (fluid temperature sensor, turbine speed, pressure switch, TCC and gear ratio tests) only run once engine speed has stayed at or below this (and at or above the low limit) for the engine run time below. Stock 6200 rpm. Effect: lower = transmission diagnostics stop at a lower engine speed Evidence: ledger:E0976</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FD2A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x568" flags="0x0">
    <title>Transmission Diagnostics Enable - Engine Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most transmission diagnostics (fluid temperature sensor, turbine speed, pressure switch, TCC and gear ratio tests) only run once engine speed has stayed inside its enable range for this long. Stock 7.0 s. Effect: raise = transmission diagnostics start later after the engine starts Evidence: ledger:E0976</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FD26" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x569" flags="0x0">
    <title>Transmission Diagnostics Enable - Output Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most transmission diagnostics (fluid temperature sensor, turbine speed, pressure switch, TCC and gear ratio tests) only run once transmission output speed has stayed at or below this for the time below. Stock 200 km/h. Effect: lower = transmission diagnostics stop at a lower speed Evidence: ledger:E0976</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FD2E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x56A" flags="0x0">
    <title>Transmission Diagnostics Enable - Output Speed Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most transmission diagnostics (fluid temperature sensor, turbine speed, pressure switch, TCC and gear ratio tests) only run once transmission output speed has stayed at or below its maximum for this long. Stock 5.0 s. Effect: raise = transmission diagnostics start later Evidence: ledger:E0976</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FD2C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x56B" flags="0x0">
    <title>Ignition On Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM treats the ignition as switched on once system voltage has been above this on two updates in a row; the engine start logic and many diagnostics wait for it. Stock 6.0 V. Effect: raise = the PCM needs more voltage before it treats the key as on (too high can stop the engine starting) Evidence: ledger:E0978</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x204B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x56C" flags="0x0">
    <title>Ignition Off Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the ignition is treated as on, the PCM treats it as off again when system voltage drops to or below this. Stock 2.0 V. Effect: raise = the PCM treats a voltage dip as key off sooner Evidence: ledger:E0978</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x204B4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x56D" flags="0x0">
    <title>Catalyst Monitor Enable - Barometric Pressure Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only arms while barometric pressure is above this. Stock 68 kPa. Effect: lower = the test can arm at higher altitude Evidence: ledger:E0984, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x56E" flags="0x0">
    <title>Catalyst Monitor Enable - Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only arms while coolant temperature is at or above this. Stock 69 C. Effect: lower = the test can arm on a cooler engine Evidence: ledger:E0984, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x56F" flags="0x0">
    <title>Catalyst Monitor Enable - Coolant Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only arms while coolant temperature is at or below this. Stock 125 C. Effect: raise = the test can arm on a hotter engine Evidence: ledger:E0984, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x570" flags="0x0">
    <title>Catalyst Monitor Enable - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: only arms while system voltage is above this. Stock 9.0 V. Effect: raise = the test needs a higher voltage to arm Evidence: ledger:E0984, ledger:E0998</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x571" flags="0x0">
    <title>Fuel Level Sensor Checks Enable - System Voltage Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel level sensor checks (P0461 range / performance, P0462 circuit low, P0463 circuit high) only run while system voltage is above this. Stock 11.0 V. Effect: raise = the checks need a higher voltage to run Evidence: ledger:E0986</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20350" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x572" flags="0x0">
    <title>Fuel Level Sensor Checks Enable - System Voltage Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel level sensor checks (P0461 range / performance, P0462 circuit low, P0463 circuit high) only run while system voltage is below this. Stock 18.0 V. Effect: lower = the checks stop at a lower voltage Evidence: ledger:E0986</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20352" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x573" flags="0x30">
    <title>Knock Detection - Reference Level Filter by Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: share of the gap to the newest sample that the reference level of a cylinder closes at each of its knock windows, in steady running, in a rising transient and in a falling transient. The knock threshold is added to this level. Stock 1.0 in all three: the reference is simply the last sample of that cylinder. Effect: lower = the reference level is smoothed over more knock windows Evidence: ledger:E1138</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>knock detection mode</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="steady" />
      <LABEL index="1" value="rising transient" />
      <LABEL index="2" value="falling transient" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31E2E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x574" flags="0x30">
    <title>Knock Detection - Noise Level Filter by Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection: share of the gap to the newest sample that the noise level of a cylinder closes at each of its knock windows, in steady running, in a rising transient and in a falling transient. The noise level drives the knock sensor amplifier gain. Stock 0.1 steady and 0.2 in transients. Effect: raise = the noise level follows the sensor signal faster Evidence: ledger:E1138</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>knock detection mode</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="steady" />
      <LABEL index="1" value="rising transient" />
      <LABEL index="2" value="falling transient" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31E34" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x575" flags="0x30">
    <title>Pedal Map - Engine Speed Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: these breakpoints are engine speed in rpm on this calibration, not vehicle speed: the pedal map row input switch is set here, so all nine pedal maps pick their row from engine speed (shown by running this operating system&#x27;s code). The text below describes the H3, where the switch is off and the rows are vehicle speed. Vehicle speed of each row of all nine pedal to throttle area maps (the rate-limited pedal map speed input). Must keep rising. Stock 0, 3, 10, 20, 40, 60, 80, 100, 120 km/h. Effect: moves the vehicle speed each pedal map row applies to, in all nine maps Evidence: ledger:E1158, ledger:E1210, l...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>breakpoint index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23E0A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x576" flags="0x30">
    <title>Accelerator Pedal Filter - Gap Points, Rising</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal gap points (pedal demand minus filtered pedal, %) at which the rising filter gain table is defined. Stock 0 to 0.094 %, the scale set by the stock rate scale word. Effect: moves the axis of the rising filter gain table: keep 17 points and keep them rising Evidence: ledger:E0330, ledger:E1190, ledger:E1329</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24002" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (pedal gap)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>95.998066</max>
      <MATH equation="X/682.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x577" flags="0x30">
    <title>Accelerator Pedal Filter - Gap Points, Falling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal gap points (pedal demand minus filtered pedal, %) at which the falling filter gain table is defined. Stock 0 to 0.094 %, the scale set by the stock rate scale word. Effect: moves the axis of the falling filter gain table: keep 17 points and keep them rising Evidence: ledger:E0330, ledger:E1190, ledger:E1329</description>
    <CATEGORYMEM index="0" category="11" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2404C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% (pedal gap)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>95.998066</max>
      <MATH equation="X/682.67"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x578" flags="0x0">
    <title>Pedal Gain Reduction - Request Factor Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest value the pedal gain reduction may cut the pedal throttle request factor to. Stock 1.0, so no cut is applied whatever the Request Factor Cut table holds. Effect: lower = the pedal gain reduction may cut the pedal request further Evidence: ledger:E0436, ledger:E1206</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23228" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x579" flags="0x0">
    <title>Pedal Gain Reduction - Step-Up Re-Arm Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The pedal gain reduction step-up is armed again once vehicle speed drops below this speed. Stock 5 km/h. Effect: raise = the step-up re-arms without the truck having to slow as far Evidence: ledger:E0436, ledger:E1208</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2322A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x57A" flags="0x0">
    <title>Pedal Gain Reduction - Step-Up Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When armed and no reduction is active, the step-up is taken once as vehicle speed rises above this speed. Stock 40 km/h. Effect: lower = the step-up is taken at a lower speed Evidence: ledger:E0436, ledger:E1208</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2322C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x57B" flags="0x0">
    <title>Pedal Gain Reduction - Request Factor Step-Up</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Amount added back to the pedal throttle request factor once per re-arm, after a pedal gain reduction, when speed rises past the Step-Up Speed. It takes effect when the pedal is released (1 percent or less) or at more than 90 percent pedal with manifold vacuum below the vacuum threshold vs rpm (stock 10 kPa); until then it waits. The factor never goes above 1.0. Stock 0, so nothing is added back. Effect: raise = more of a pedal gain reduction is given back each time the truck speeds up again Evidence: ledger:E0436, ledger:E1208</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2322E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x57C" flags="0x30">
    <title>Pedal Map Select vs Trans State - Normal</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Which pedal to throttle map is used in each transmission state in normal driving: 0 = Gears 1-3 + Park/Neutral map, 1 = 4th Gear map, 2 = Reverse map. Stock 1 in 4th and 2 in Reverse, 0 elsewhere. The choice changes only while the pedal is at rest or wide open. Allowed values are 0, 1 and 2 only; any other value makes the pedal read the wrong map or no map. Effect: changes which pedal map is used in that transmission state Evidence: ledger:E0240, ledger:E1210</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>transmission state</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="state 4" />
      <LABEL index="5" value="state 5" />
      <LABEL index="6" value="Neutral" />
      <LABEL index="7" value="Reverse" />
      <LABEL index="8" value="Park" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23D84" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>map slot</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x57D" flags="0x0">
    <title>Pedal Request Factor - Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest value the combined pedal request factor (the product of all pedal request factors, including the pedal gain increase) may reach. Stock 1.0, so the pedal gain increase cannot raise the pedal request above the map value. Range 0 to 2.0. Effect: raise = lets the pedal gain increase raise the pedal request above the map value Evidence: ledger:E0436, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23230" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x57E" flags="0x0">
    <title>Pedal Gain Increase - Maximum Speed Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The pedal gain increase learn runs only in a launch: below the Maximum Speed, input / output speed ratio at or below the Maximum Speed Ratio and acceleration above the Minimum Acceleration. On stock it never runs (ratio 0 and 120 km/h/s). This is the highest transmission input / output speed ratio at which it runs. Stock 0. Effect: raise = the learn may run (it needs a ratio at or below this) Evidence: ledger:E0436, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23234" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>:1</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x57F" flags="0x0">
    <title>Pedal Gain Increase - Maximum Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The pedal gain increase learn runs only in a launch: below the Maximum Speed, input / output speed ratio at or below the Maximum Speed Ratio and acceleration above the Minimum Acceleration. On stock it never runs (ratio 0 and 120 km/h/s). This is the speed below which it runs. Stock 20 km/h. Effect: raise = the learn runs up to a higher speed Evidence: ledger:E0436, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23236" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x580" flags="0x0">
    <title>Pedal Gain Increase - Minimum Acceleration</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The pedal gain increase learn runs only in a launch: below the Maximum Speed, input / output speed ratio at or below the Maximum Speed Ratio and acceleration above the Minimum Acceleration. On stock it never runs (ratio 0 and 120 km/h/s). This is the acceleration above which it runs. Stock 120 km/h/s (never reached). Effect: lower = the learn runs at milder acceleration Evidence: ledger:E0436, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23238" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x581" flags="0x0">
    <title>Pedal Gain Increase - Samples per Update</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of passes the pedal gain increase learn averages before it updates the increase (each pass adds the pedal gain reduction acceleration threshold divided by the measured acceleration). Stock 40. Effect: raise = the increase updates less often, from a longer average Evidence: ledger:E0436, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2323A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x582" flags="0x0">
    <title>Pedal Gain Increase - Rise Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the way the pedal gain increase moves toward a higher new value at each update. Stock 1.0 (all the way). Range 0 to 1.0. Effect: lower = the increase builds up over more updates Evidence: ledger:E0436, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23250" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x583" flags="0x0">
    <title>Pedal Gain Increase - Fall Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the way the pedal gain increase moves toward a lower new value at each update. Stock 1.0 (all the way). Range 0 to 1.0. Effect: lower = the increase falls away over more updates Evidence: ledger:E0436, ledger:E1211</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x23252" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x584" flags="0x30">
    <title>Pedal Map - Pedal Position Breakpoints (axis, edit with care)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal position of each column of all nine pedal to throttle area maps. Must keep rising from left to right. Stock 0, 3.1, 6.3, 12.5 then 6.25 % steps to 87.5, last column 97.0 %. At or below the first breakpoint the throttle area demand is 0 whatever the maps hold. Effect: moves the pedal position each pedal map column applies to, in all nine maps Evidence: ledger:E0232, ledger:E1214</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>breakpoint index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23DE6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x585" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - Trans State 5</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in transmission state 5 (not used on the 4-speed). 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E14" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x586" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - Trans State 4, Converter Clutch Applied</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in transmission state 4 (not used on the 4-speed) with the converter clutch applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E16" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x587" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - Trans State 4, Converter Clutch Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in transmission state 4 (not used on the 4-speed) with the converter clutch not applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E18" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x588" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 4th Gear, Converter Clutch Applied</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 4th gear with the converter clutch applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E1A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x589" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 4th Gear, Converter Clutch Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 4th gear with the converter clutch not applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E1C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x58A" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 3rd Gear, Converter Clutch Applied</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 3rd gear with the converter clutch applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E1E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x58B" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 3rd Gear, Converter Clutch Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 3rd gear with the converter clutch not applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E20" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x58C" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 2nd, Neutral, Reverse, Park, Warm, Converter Clutch Applied</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 2nd gear, Neutral, Reverse or Park, coolant at or above the cold threshold, converter clutch applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E22" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x58D" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 2nd, Neutral, Reverse, Park, Warm, Converter Clutch Off</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 2nd gear, Neutral, Reverse or Park, coolant at or above the cold threshold, converter clutch not applied. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E24" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x58E" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 2nd, Neutral, Reverse, Park, Cold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 2nd gear, Neutral, Reverse or Park with the coolant below the cold threshold. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E26" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x58F" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 1st Gear, Warm</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 1st gear with the coolant at or above the cold threshold. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E28" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x590" flags="0x0">
    <title>Closed Loop Proportional Term Ceiling Factor - 1st Gear, Cold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the Closed Loop Proportional Term Ceiling vs Airflow in 1st gear with the coolant below the cold threshold. 1.0 uses the curve as is. Stock 2.0 (no limit). Range -2.0 to 2.0. Effect: lower = a tighter cap on the closed loop proportional correction Evidence: ledger:E0903, ledger:E1216</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E2A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x591" flags="0x0">
    <title>First-Run Mode - Run Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First-run mode runs only during the first 12 s of engine running recorded by the PCM (kept through power-off), with a stored flag set, the mode enable set and start-up coolant inside the coolant window. This is the recorded run time it lasts. Stock 12 s. Effect: raise = first-run mode lasts longer Evidence: ledger:E0436, ledger:E1227</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x26E10" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x592" flags="0x0">
    <title>First-Run Mode - Start-Up Coolant Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First-run mode runs only during the first 12 s of engine running recorded by the PCM (kept through power-off), with a stored flag set, the mode enable set and start-up coolant inside the coolant window. This is the highest start-up coolant temperature it accepts. Stock 50 C. Effect: raise = first-run mode also runs on warmer starts Evidence: ledger:E0436, ledger:E1227</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x26E14" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x593" flags="0x0">
    <title>First-Run Mode - Start-Up Coolant Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First-run mode runs only during the first 12 s of engine running recorded by the PCM (kept through power-off), with a stored flag set, the mode enable set and start-up coolant inside the coolant window. This is the lowest start-up coolant temperature it accepts. Stock 10 C. Effect: lower = first-run mode also runs on colder starts Evidence: ledger:E0436, ledger:E1227</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x26E16" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x594" flags="0x30">
    <title>A/C Idle Air - RPM Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Multiplies the A/C idle air target by engine speed (0 to 6400 rpm). Shown with 1.0 = stock, because the A/C idle air target&#x27;s scaling already includes the stock factor; 2.0 doubles the A/C idle air at that speed. Stock 1.0 everywhere. Effect: raise = more idle air for the A/C compressor at that engine speed Evidence: ledger:E1230</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="400" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1200" />
      <LABEL index="4" value="1600" />
      <LABEL index="5" value="2000" />
      <LABEL index="6" value="2400" />
      <LABEL index="7" value="2800" />
      <LABEL index="8" value="3200" />
      <LABEL index="9" value="3600" />
      <LABEL index="10" value="4000" />
      <LABEL index="11" value="4400" />
      <LABEL index="12" value="4800" />
      <LABEL index="13" value="5200" />
      <LABEL index="14" value="5600" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29BB2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x595" flags="0x0">
    <title>P0506 / P0507 Pass - Idle Speed Error Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The tests pass once the filtered idle speed error (either direction) stays at or below this for the pass time. Stock 50 rpm. Part of the idle speed diagnostic (P0506 idle speed lower than expected, P0507 higher than expected), which runs only once its enable conditions are met. Effect: raise = the tests pass with a larger idle speed error Evidence: ledger:E0639, ledger:E1239</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37FD4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x596" flags="0x0">
    <title>P0506 / P0507 Pass - Idle Speed Error Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain for the idle speed error used by the pass check (fraction of the new error taken each update). Stock 0.2. Part of the idle speed diagnostic (P0506 idle speed lower than expected, P0507 higher than expected), which runs only once its enable conditions are met. Effect: raise = the filtered error follows the idle speed error faster Evidence: ledger:E0639, ledger:E1239</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37FD6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x597" flags="0x0">
    <title>P0506 / P0507 Pass - Time Within Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the filtered idle speed error must stay within the pass maximum before both tests report a pass and the fail period counts are cleared. Stock 3 s. Part of the idle speed diagnostic (P0506 idle speed lower than expected, P0507 higher than expected), which runs only once its enable conditions are met. Effect: raise = longer stable idle needed for a pass Evidence: ledger:E0639, ledger:E1239</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37FD8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x598" flags="0x0">
    <title>Vehicle Bus - A/C Refrigerant Pressure Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the change threshold for the A/C refrigerant pressure message. Stock 28 kPa. Effect: raise = fewer, coarser updates Evidence: ledger:E1243</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2021A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x599" flags="0x0">
    <title>Vehicle Bus - A/C Refrigerant Pressure Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the minimum interval for the A/C refrigerant pressure message. Stock 0.3 s. Effect: raise = less frequent updates Evidence: ledger:E1243</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2021C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x59A" flags="0x0">
    <title>Vehicle Bus - Coolant Temperature Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent. This is the change threshold for the coolant temperature message (no minimum interval). Stock 1 C. Effect: raise = fewer, coarser updates Evidence: ledger:E1243</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20222" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x59B" flags="0x0">
    <title>Vehicle Bus - Engine Torque Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the change threshold for the engine torque message. Stock 10 Nm. Effect: raise = fewer, coarser updates Evidence: ledger:E1243</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20224" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>16383.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x59C" flags="0x0">
    <title>Vehicle Bus - Engine Torque Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the minimum interval for the engine torque message. Stock 0.1 s. Effect: raise = less frequent updates Evidence: ledger:E1243</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20226" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x59D" flags="0x0">
    <title>Vehicle Bus - Engine Speed Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the change threshold for the engine speed message. Stock 16 rpm. Effect: raise = fewer, coarser updates Evidence: ledger:E1243</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2022C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x59E" flags="0x0">
    <title>Vehicle Bus - Engine Speed Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the minimum interval for the engine speed message. Stock 0.1 s. Effect: raise = less frequent updates Evidence: ledger:E1243</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2022E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x59F" flags="0x0">
    <title>Vehicle Bus - Vehicle Speed Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the change threshold for the vehicle speed message. Stock 0.2 km/h. Effect: raise = fewer, coarser updates Evidence: ledger:E1244</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20250" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5A0" flags="0x0">
    <title>Vehicle Bus - Vehicle Speed Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this value to other modules on the vehicle bus: a new message goes out once the value has changed by the change threshold since the last one sent and at least the minimum interval has passed. This is the minimum interval for the vehicle speed message. Stock 0.1 s. Effect: raise = less frequent updates Evidence: ledger:E1244</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20254" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5A1" flags="0x0">
    <title>High Engine Speed State 1 - Step-Up Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. High engine speed state: it steps up from normal to the first high state, and from there to the second, as engine speed rises past the step-up speeds, and back down at the step-down speeds. In either high state the airmass is taken from the mass airflow sensor only; fuel and spark routines also read the state. The state goes from normal to the first high state above this speed. Stock 5000 rpm. Effect: raise = MAF-only airmass starts at a higher speed Evidence: ledger:E0219, ledger:E0868, ledger:E1245</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22CEA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5A2" flags="0x0">
    <title>High Engine Speed State 1 - Step-Down Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. High engine speed state: it steps up from normal to the first high state, and from there to the second, as engine speed rises past the step-up speeds, and back down at the step-down speeds. In either high state the airmass is taken from the mass airflow sensor only; fuel and spark routines also read the state. The state goes from the first high state back to normal at or below this speed. Stock 4900 rpm. Effect: lower = the high state holds to a lower speed Evidence: ledger:E0219, ledger:E0868, ledger:E1245</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22CEC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5A3" flags="0x0">
    <title>High Engine Speed State 2 - Step-Up Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. High engine speed state: it steps up from normal to the first high state, and from there to the second, as engine speed rises past the step-up speeds, and back down at the step-down speeds. In either high state the airmass is taken from the mass airflow sensor only; fuel and spark routines also read the state. The state goes from the first to the second high state above this speed. Stock 5800 rpm. Effect: raise = the second high state starts at a higher speed Evidence: ledger:E0219, ledger:E0868, ledger:E1245</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22CEE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5A4" flags="0x0">
    <title>High Engine Speed State 2 - Step-Down Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. High engine speed state: it steps up from normal to the first high state, and from there to the second, as engine speed rises past the step-up speeds, and back down at the step-down speeds. In either high state the airmass is taken from the mass airflow sensor only; fuel and spark routines also read the state. The state goes from the second high state back to the first at or below this speed. Stock 5700 rpm. Effect: lower = the second high state holds to a lower speed Evidence: ledger:E0219, ledger:E0868, ledger:E1245</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x22CF0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5A5" flags="0x30">
    <title>Closed Loop O2 Filter Gain - Error Signal, Bank 2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): filter on the O2 voltage that is used to work out how far the signal is past the switch point (the input of the step interval and proportional factors), by airflow. Share of each new reading taken every 12.5 ms. Stock 0.005 at idle rising to 0.1. This is the row for a second bank of cylinders. Stock values are the same as the bank 1 curve. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1126, ledger:E1247</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s used airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4.8" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="13.2" />
      <LABEL index="4" value="21.8" />
      <LABEL index="5" value="29.5" />
      <LABEL index="6" value="40.3" />
      <LABEL index="7" value="51.8" />
      <LABEL index="8" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24E56" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5A6" flags="0x30">
    <title>Closed Loop O2 Filter Gain - Purge Feedback Signal, Bank 2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Front O2: filter on the O2 voltage that the canister purge feedback reads, by airflow. Share of each new reading taken every 12.5 ms. Stock 0.005 at idle rising to 0.14. This is the row for a second bank of cylinders. Stock values are the same as the bank 1 curve. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1126, ledger:E1247</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s used airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4.8" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="13.2" />
      <LABEL index="4" value="21.8" />
      <LABEL index="5" value="29.5" />
      <LABEL index="6" value="40.3" />
      <LABEL index="7" value="51.8" />
      <LABEL index="8" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24E7E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5A7" flags="0x30">
    <title>Closed Loop O2 Filter Gain - Rich / Lean Decision, Bank 2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed loop fuel (front O2): filter on the O2 voltage that is compared with the switch point to decide rich or lean, by airflow. Share of each new reading taken every 12.5 ms. Stock 0.5 at idle and 1.0 (no filtering) off idle. This is the row for a second bank of cylinders. Stock values are the same as the bank 1 curve. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1126, ledger:E1247</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>g/s used airflow</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4.8" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="13.2" />
      <LABEL index="4" value="21.8" />
      <LABEL index="5" value="29.5" />
      <LABEL index="6" value="40.3" />
      <LABEL index="7" value="51.8" />
      <LABEL index="8" value="76" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24EA6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5A8" flags="0x30">
    <title>Purge Valve Duty vs Flow Demand - 163 to 327 Flow Units</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge: purge valve duty for a purge flow demand between 163 and 327 flow units, continuing the main Purge Valve Duty vs Flow Demand curve (0 to 163); above 655 the duty is 100 %. Stock 100 % in every cell. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0950, ledger:E1122, ledger:E1250</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>flow units demand</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="163" />
      <LABEL index="1" value="168.125" />
      <LABEL index="2" value="173.25" />
      <LABEL index="3" value="178.375" />
      <LABEL index="4" value="183.5" />
      <LABEL index="5" value="188.625" />
      <LABEL index="6" value="193.75" />
      <LABEL index="7" value="198.875" />
      <LABEL index="8" value="204" />
      <LABEL index="9" value="209.125" />
      <LABEL index="10" value="214.25" />
      <LABEL index="11" value="219.375" />
      <LABEL index="12" value="224.5" />
      <LABEL index="13" value="229.625" />
      <LABEL index="14" value="234.75" />
      <LABEL index="15" value="239.875" />
      <LABEL index="16" value="245" />
      <LABEL index="17" value="250.125" />
      <LABEL index="18" value="255.25" />
      <LABEL index="19" value="260.375" />
      <LABEL index="20" value="265.5" />
      <LABEL index="21" value="270.625" />
      <LABEL index="22" value="275.75" />
      <LABEL index="23" value="280.875" />
      <LABEL index="24" value="286" />
      <LABEL index="25" value="291.125" />
      <LABEL index="26" value="296.25" />
      <LABEL index="27" value="301.375" />
      <LABEL index="28" value="306.5" />
      <LABEL index="29" value="311.625" />
      <LABEL index="30" value="316.75" />
      <LABEL index="31" value="321.875" />
      <LABEL index="32" value="327" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24294" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.781250</max>
      <MATH equation="X/326.4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5A9" flags="0x30">
    <title>Purge Valve Duty vs Flow Demand - 327 to 655 Flow Units</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Canister purge: purge valve duty for a purge flow demand between 327 and 655 flow units, continuing the main Purge Valve Duty vs Flow Demand curve (0 to 163); above 655 the duty is 100 %. Stock 100 % in every cell. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0950, ledger:E1122, ledger:E1250</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>flow units demand</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="327" />
      <LABEL index="1" value="337.25" />
      <LABEL index="2" value="347.5" />
      <LABEL index="3" value="357.75" />
      <LABEL index="4" value="368" />
      <LABEL index="5" value="378.25" />
      <LABEL index="6" value="388.5" />
      <LABEL index="7" value="398.75" />
      <LABEL index="8" value="409" />
      <LABEL index="9" value="419.25" />
      <LABEL index="10" value="429.5" />
      <LABEL index="11" value="439.75" />
      <LABEL index="12" value="450" />
      <LABEL index="13" value="460.25" />
      <LABEL index="14" value="470.5" />
      <LABEL index="15" value="480.75" />
      <LABEL index="16" value="491" />
      <LABEL index="17" value="501.25" />
      <LABEL index="18" value="511.5" />
      <LABEL index="19" value="521.75" />
      <LABEL index="20" value="532" />
      <LABEL index="21" value="542.25" />
      <LABEL index="22" value="552.5" />
      <LABEL index="23" value="562.75" />
      <LABEL index="24" value="573" />
      <LABEL index="25" value="583.25" />
      <LABEL index="26" value="593.5" />
      <LABEL index="27" value="603.75" />
      <LABEL index="28" value="614" />
      <LABEL index="29" value="624.25" />
      <LABEL index="30" value="634.5" />
      <LABEL index="31" value="644.75" />
      <LABEL index="32" value="655" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x242DC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>200.781250</max>
      <MATH equation="X/326.4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5AA" flags="0x0">
    <title>P2138 Pedal Position Sensor Correlation - Failed Samples to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2138: the PCM compares the two accelerator pedal position sensors. Once a sample has failed, the test counts samples; the code sets when this many have failed before the sample window is reached. Stock 15. Effect: raise = more failed samples are needed to set the code Evidence: ledger:E0434, ledger:E1251</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DE4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5AB" flags="0x0">
    <title>P2138 Pedal Position Sensor Correlation - Consecutive Failed Samples to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2138: the PCM compares the two accelerator pedal position sensors. The code also sets when this many samples in a row have failed. Stock 12. Effect: raise = a longer run of failed samples is needed Evidence: ledger:E0434, ledger:E1251</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DF0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5AC" flags="0x0">
    <title>P2138 Pedal Position Sensor Correlation - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2138: the PCM compares the two accelerator pedal position sensors. Counted from the first failed sample: when this many samples are reached without the code setting, both counts start again. Stock 35. Effect: raise = failures are collected over a longer window Evidence: ledger:E0434, ledger:E1251</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DF4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5AD" flags="0x0">
    <title>P2138 Pedal Position Sensor Correlation - Allowed Difference, Share of Lower Reading</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2138: the PCM compares the two accelerator pedal position sensors. The allowed difference between the two readings is this share of the lower reading plus a fixed part; a larger difference counts as a failed sample. Stock 5.00 %. Effect: raise = a larger difference is tolerated Evidence: ledger:E0434, ledger:E1251</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DEC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5AE" flags="0x0">
    <title>P2135 Throttle Position Sensor Correlation - Failed Samples to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2135: the PCM compares the two throttle position sensors. Once a sample has failed, the test counts samples; the code sets when this many have failed before the sample window is reached. Stock 15. Effect: raise = more failed samples are needed to set the code Evidence: ledger:E0434, ledger:E1252</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22EAC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5AF" flags="0x0">
    <title>P2135 Throttle Position Sensor Correlation - Consecutive Failed Samples to Set</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2135: the PCM compares the two throttle position sensors. The code also sets when this many samples in a row have failed. Stock 12. Effect: raise = a longer run of failed samples is needed Evidence: ledger:E0434, ledger:E1252</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22EAE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5B0" flags="0x0">
    <title>P2135 Throttle Position Sensor Correlation - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2135: the PCM compares the two throttle position sensors. Counted from the first failed sample: when this many samples are reached without the code setting, both counts start again. Stock 35. Effect: raise = failures are collected over a longer window Evidence: ledger:E0434, ledger:E1252</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22EB0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5B1" flags="0x0">
    <title>P2135 Throttle Position Sensor Correlation - Allowed Difference, Share of Lower Reading</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P2135: the PCM compares the two throttle position sensors. The allowed difference between the two readings is this share of the lower reading plus a fixed part; a larger difference counts as a failed sample. Stock 4.98 %. Effect: raise = a larger difference is tolerated Evidence: ledger:E0434, ledger:E1252</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22EA6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5B2" flags="0x30">
    <title>Catalyst Monitor Enable - Minimum O2 Switches During Trim Averaging</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): the upstream O2 sensor must change between rich and lean at least this many times during the short term trim sampling time, or the test stops for this run (one value per catalyst). This truck has one bank and uses the first value; the second is for a second bank and has no effect on the stock calibration (dormant). Stock 4. Effect: raise = the test needs more O2 switching before it goes on Evidence: ledger:E0437, ledger:E1188, ledger:E1254</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>catalyst</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x345EC" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>switches</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5B3" flags="0x0">
    <title>High-Load Monitor - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. High-load monitor: once the time spent at high load (intake vacuum below the threshold) passes this, the monitor sets its flag and acts. Stock 10.0 s. Effect: raise = longer at high load before the monitor acts Evidence: ledger:E0775, ledger:E1265</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22EC8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5B4" flags="0x0">
    <title>Crank Wheel - Reference Events per Revolution (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of crank reference events per crankshaft revolution (one every 12 teeth), used to turn the reference event period into engine speed. Stock 5. Reference only: DO NOT EDIT. Effect: reference only (crank wheel geometry) Evidence: ledger:E0324, ledger:E1274, ledger:E1276</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x22C7A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>events per revolution</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5B5" flags="0x0">
    <title>Engine Stopped Detection - Time Without Crank Signal</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When no crank reference event arrives for this long, the engine speed it measures is set to zero (the engine counts as stopped). Stock 4 s. Effect: raise = the PCM waits longer without crank signal before reporting the engine stopped Evidence: ledger:E0324, ledger:E1274, ledger:E1276</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x22C88" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5B6" flags="0x0">
    <title>Cam Sensor Fault Start - Running Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cranking strategy for a failed cam sensor: above this engine speed the engine counts as running, and once it has run for the running time below the strategy stops for this start. Stock 300 rpm. Effect: raise = the engine must reach a higher speed before the cam fault cranking strategy stands down Evidence: ledger:E0324, ledger:E1274, ledger:E1275</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x22D48" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5B7" flags="0x30">
    <title>Airmass Predictor - Feedback Gain on Previous Estimate (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Multiplies the previous airmass estimate and adds it to the new prediction (1.0 = full carry-over). Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C7CE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5B8" flags="0x30">
    <title>Airmass Predictor - Gain on MAF Airmass (current sample) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Multiplies the current MAF cylinder airmass sample in the prediction. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C7F2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-1.000000</min>
      <max>0.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5B9" flags="0x30">
    <title>Airmass Predictor - Blend Toward Prediction (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Fraction of the way from the prediction to the filtered MAF airmass that the airmass estimate takes (0 = prediction only, 1.0 = filtered MAF airmass only). Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277, ledger:E1521</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C816" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5BA" flags="0x30">
    <title>Airmass Predictor - Gain on MAF Airmass (previous sample) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Multiplies the previous MAF cylinder airmass sample in the prediction. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C83A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>-1.000000</min>
      <max>0.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5BB" flags="0x30">
    <title>Airmass Predictor - Gain on MAP (current sample) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Cylinder airmass added per kPa of the current MAP sample. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C85E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mg/cyl per kPa</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5BC" flags="0x30">
    <title>Airmass Predictor - Gain on MAP (one sample back) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Cylinder airmass added per kPa of the MAP sample one step back. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C882" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mg/cyl per kPa</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5BD" flags="0x30">
    <title>Airmass Predictor - Gain on MAP (two samples back) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Cylinder airmass added per kPa of the MAP sample two steps back. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C8A6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mg/cyl per kPa</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5BE" flags="0x30">
    <title>Airmass Predictor - Gain on Throttle Area (current sample) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Cylinder airmass added per % of the current throttle area sample. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C8CA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mg/cyl per %</units>
      <decimalpl>0</decimalpl>
      <min>-40.960000</min>
      <max>40.958750</max>
      <MATH equation="X/800"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5BF" flags="0x30">
    <title>Airmass Predictor - Gain on Throttle Area (one sample back) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Cylinder airmass added per % of the throttle area sample one step back. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C8EE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mg/cyl per %</units>
      <decimalpl>0</decimalpl>
      <min>-40.960000</min>
      <max>40.958750</max>
      <MATH equation="X/800"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5C0" flags="0x30">
    <title>Airmass Predictor - Gain on Throttle Area (two samples back) (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Cylinder airmass added per % of the throttle area sample two steps back. Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:E0323, ledger:E1277</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C912" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mg/cyl per %</units>
      <decimalpl>0</decimalpl>
      <min>-40.960000</min>
      <max>40.958750</max>
      <MATH equation="X/800"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5C1" flags="0x0">
    <title>Trans-Side Vehicle Speed - Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain for the vehicle speed the transmission computes from output shaft speed, tire size and axle ratio (stock 0.1 per update); the filtered speed is the one the shift and converter clutch logic use. Effect: raise = the transmission&#x27;s speed follows changes faster (less smoothing) Evidence: ledger:E1299</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FB36" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5C2" flags="0x0">
    <title>Trans-Side Vehicle Acceleration - Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain for trans-side vehicle acceleration, updated every 100 ms (stock 0.1 per update). Smoothed trans-side vehicle acceleration sets an accelerating flag read by the shift and converter clutch logic; between the on and off values the flag keeps its last state. Effect: raise = the acceleration and its flag react faster Evidence: ledger:E1299</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FB38" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5C3" flags="0x30">
    <title>Accelerating Flag - On Above, by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Acceleration above which the flag sets, for 1st to 3rd gear (stock -255 / 2.0 / 1.0: always on in 1st). Smoothed trans-side vehicle acceleration sets an accelerating flag read by the shift and converter clutch logic; between the on and off values the flag keeps its last state. In 4th gear the code reads one value past this list (for the on value the 1st gear off value, for the off value the deceleration filter gain), so on the stock calibration the flag stays on in 4th. Effect: raise = the flag needs harder acceleration to set in that gear Evidence: ledger:E1299</description>
    <CATEGORYMEM index="0" category="10" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3FB3C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per s</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5C4" flags="0x30">
    <title>Accelerating Flag - Off Below, by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Acceleration below which the flag clears, for 1st to 3rd gear (stock -255 / 0.6 / 0.6). Smoothed trans-side vehicle acceleration sets an accelerating flag read by the shift and converter clutch logic; between the on and off values the flag keeps its last state. In 4th gear the code reads one value past this list (for the on value the 1st gear off value, for the off value the deceleration filter gain), so on the stock calibration the flag stays on in 4th. Effect: raise = the flag clears sooner as acceleration falls Evidence: ledger:E1299</description>
    <CATEGORYMEM index="0" category="10" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>gear</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3FB42" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per s</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5C5" flags="0x0">
    <title>Output Shaft Speed Tracker - Speed Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of the speed error added to the tracked output shaft speed each update. Stock 0.277. The output shaft speed tracker follows the output speed sensor with three estimates (speed, rate of change and acceleration), each corrected by its share of the speed error every update; the rate of change estimate is used by the shift and converter clutch logic. Effect: raise = the tracked speed follows the sensor faster but passes more noise Evidence: ledger:E1305</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FB0C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5C6" flags="0x0">
    <title>Output Shaft Speed Tracker - Rate Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of the speed error added to the tracked rate of change of output shaft speed each update. Stock 1.369. The output shaft speed tracker follows the output speed sensor with three estimates (speed, rate of change and acceleration), each corrected by its share of the speed error every update; the rate of change estimate is used by the shift and converter clutch logic. Effect: raise = the output speed rate of change reacts faster but is noisier Evidence: ledger:E1305</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FB0E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5C7" flags="0x0">
    <title>Output Shaft Speed Tracker - Acceleration Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fraction of the speed error added to the tracked output shaft acceleration each update. Stock 0.615. The output shaft speed tracker follows the output speed sensor with three estimates (speed, rate of change and acceleration), each corrected by its share of the speed error every update; the rate of change estimate is used by the shift and converter clutch logic. Effect: raise = the tracked acceleration reacts faster but is noisier Evidence: ledger:E1305</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FB10" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5C8" flags="0x0">
    <title>Output Shaft Speed Change Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How quickly the filtered change of output shaft speed per update follows each new measurement, as the fraction of the difference taken per update. Stock 0.10. Effect: raise = the filtered speed change reacts faster but is noisier Evidence: ledger:E1305</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FB12" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>gain</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5C9" flags="0x0">
    <title>TCC Slip Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Smoothing of the converter slip (engine speed minus transmission input speed) that the converter clutch logic uses: each update the filtered slip moves this fraction of the way to the measured slip (stock 0.25). Effect: raise = filtered slip follows measured slip faster (less smoothing); lower = smoother, slower slip signal Evidence: ledger:E1310</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3F9E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5CA" flags="0x0">
    <title>STFT Tip-In Reset - Throttle Request Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Short term fuel trim tip-in reset: the reset is armed when the throttle area request above the idle area rises from below this to at or above it, at low speed (STFT Tip-In Reset Speed Maximum). Stock 2.0 % above idle. See STFT Tip-In Reset Threshold for what the reset does. Effect: raise = a larger throttle opening is needed to trigger the tip-in reset Evidence: ledger:E1313</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24DF4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5CB" flags="0x0">
    <title>First-Run Mode - Cranking Fuel Multiplier</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While first-run mode is active (the first engine running recorded by the PCM, see the First-Run Mode items), the stage 1 cranking fuel multiplier (Cranking FA Mult Stage 1 vs. Cranking Time) is multiplied by this. Stock 2.0: double cranking fuel on a first start. Effect: raise = more cranking fuel during first-run mode Evidence: ledger:E1315</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26E0E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>7.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5CC" flags="0x0">
    <title>Alternator Field Duty Filter - Idle Airflow Input</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The alternator field (F-terminal) duty reading is filtered into the alternator load input of the idle airflow (the electrical load term of the idle airflow sum). Each update moves the filtered value this fraction of the way to the new reading. Stock 0.20. Effect: raise = the idle airflow follows alternator load changes faster Evidence: ledger:E1315</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x203E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5CD" flags="0x0">
    <title>Alternator Field Duty Filter - Reported Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The alternator field (F-terminal) duty reading is filtered into the value the scan tool reports as alternator F-terminal duty and the charging system checks use. Each update moves the filtered value this fraction of the way to the new reading. Stock 0.40. Effect: raise = the reported duty and the charging checks follow the reading faster Evidence: ledger:E1315</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x203EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5CE" flags="0x0">
    <title>Fuel Level - Sender Table Full Scale</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The Fuel Level vs Sender Voltage table value that counts as a full tank: the fuel level the PCM reports and uses (both fuel level paths) is the table value divided by this. Shown in the table&#x27;s own percent; stock 100 %. Effect: raise = every fuel level reading drops in proportion (less fuel shown for the same sender voltage) Evidence: ledger:E1316</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x203B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>292.763011</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/223.85"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5CF" flags="0x30">
    <title>Fuel Level 2 - Level vs Sender Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converts the filtered fuel level sender voltage (0 to 5 V in 0.156 V steps) to the second fuel level. Stock reads full (101 %) up to about 0.8 V and empty from about 2.7 V, close to the first fuel level table. Second fuel level, used by the starter low-voltage hold and sent in a data message. Values are fuel level as read from the sender curve, before the offset. Effect: change only to match a different fuel sender Evidence: ledger:E1036, ledger:E1331</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>V (fuel level sender)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.156" />
      <LABEL index="2" value="0.312" />
      <LABEL index="3" value="0.469" />
      <LABEL index="4" value="0.625" />
      <LABEL index="5" value="0.781" />
      <LABEL index="6" value="0.938" />
      <LABEL index="7" value="1.094" />
      <LABEL index="8" value="1.25" />
      <LABEL index="9" value="1.406" />
      <LABEL index="10" value="1.562" />
      <LABEL index="11" value="1.719" />
      <LABEL index="12" value="1.875" />
      <LABEL index="13" value="2.031" />
      <LABEL index="14" value="2.188" />
      <LABEL index="15" value="2.344" />
      <LABEL index="16" value="2.5" />
      <LABEL index="17" value="2.656" />
      <LABEL index="18" value="2.812" />
      <LABEL index="19" value="2.969" />
      <LABEL index="20" value="3.125" />
      <LABEL index="21" value="3.281" />
      <LABEL index="22" value="3.438" />
      <LABEL index="23" value="3.594" />
      <LABEL index="24" value="3.75" />
      <LABEL index="25" value="3.906" />
      <LABEL index="26" value="4.062" />
      <LABEL index="27" value="4.219" />
      <LABEL index="28" value="4.375" />
      <LABEL index="29" value="4.531" />
      <LABEL index="30" value="4.688" />
      <LABEL index="31" value="4.844" />
      <LABEL index="32" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2036E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% fuel level</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>292.763011</max>
      <MATH equation="X/223.85"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5D0" flags="0x0">
    <title>Fuel Level 2 - Level Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Subtracted from the sender curve&#x27;s level before it is filtered into the second fuel level (stock 1.0 %); the first fuel level calculation subtracts it as well. Second fuel level, used by the starter low-voltage hold and sent in a data message. Values are fuel level as read from the sender curve, before the offset. Effect: raise = the fuel level reads lower by that much Evidence: ledger:E1036, ledger:E1331</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x20360" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% fuel level</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>292.763011</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/223.85"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5D1" flags="0x0">
    <title>Fuel Level 2 - Low Fuel Timer Start Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this level the low fuel timer starts; once it runs for the low fuel time the fast filter is used (stock 3.4 %). Second fuel level, used by the starter low-voltage hold and sent in a data message. Values are fuel level as read from the sender curve, before the offset. Effect: raise = low fuel handling starts at a higher level Evidence: ledger:E1036, ledger:E1331</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x20362" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% fuel level</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>292.763011</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/223.85"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5D2" flags="0x0">
    <title>Fuel Level 2 - Low Fuel Clear Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or above this level the low fuel timer is cleared, and above it the low fuel state ends and the normal slow filter returns (stock 9.7 %). Second fuel level, used by the starter low-voltage hold and sent in a data message. Values are fuel level as read from the sender curve, before the offset. Effect: raise = the level must recover further before low fuel handling ends Evidence: ledger:E1036, ledger:E1331</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x20364" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% fuel level</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>292.763011</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/223.85"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5D3" flags="0x0">
    <title>Knock Retard - Park / Neutral Start-Up Hold-Off Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. For this long after the engine starts, while the transmission is in Park or Neutral, the knock retard update for each cylinder is skipped and the knock-active flag is cleared, so no new knock retard is added. In gear, or after this time, knock retard works normally. Stock 10 s. Effect: raise = knock retard stays off longer after a start in Park or Neutral Evidence: ledger:E1333</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2BACA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5D4" flags="0x0">
    <title>Crank Signal Loss - Reference Period Speed Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When no crank reference event (one every 12 teeth) arrives for this long, the engine speed measured from the reference period is marked invalid and its period set to the maximum, so the PCM takes engine speed from the tooth period measurement instead. Companion of Crank and Cam Signal Loss Watchdog B. Stock 0.4 s. Effect: raise = a lost crank reference signal is noticed later Evidence: ledger:E1333</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x22CB0" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5D5" flags="0x30">
    <title>Ambient Air Temp Estimate - Flush Requirement vs Soak Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Seconds of qualifying driving (above the airflow and speed gates, at flush weight 1.0) needed before the ambient air temperature estimate may rise again, by engine-off soak time. Stock 60 s after a short stop, up to 80 s after about 40 minutes, down to 20 s near 7 hours. If the previous drive ended before the estimate was released, the largest value of this curve is used. The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it d...</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x35FB0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <indexcount>33</indexcount>
      <units>s</units>
      <embedinfo type="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35F68" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>204.796875</max>
      <MATH equation="X/320"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5D6" flags="0x0">
    <title>Ambient Air Temp Estimate - Soak Time for Immediate Reset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After an engine-off soak at least this long (stock 25200 s = 7 h) the ambient estimate is taken straight from the intake air temperature at start-up and no flush is required. The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it down, and until it reaches zero the estimate can only fall toward the intake air temperature. Effect: lower = the intake reading is trusted at start-up after a shorter soak Evidence: ledger:E0385, ledg...</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x35FAA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5D7" flags="0x0">
    <title>Ambient Air Temp Estimate - Soak Time Limit for Stored Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a soak up to this long (stock 7200 s = 2 h) the ambient estimate starts from the value stored at the end of the last drive when that is lower than the intake air temperature; after a longer soak it starts from the intake air temperature. The ambient air temperature estimate is held back after a short engine-off soak, because the intake air sensor then reads heat soaked air. The PCM sets a flush requirement from the soak time; each second of driving above the airflow and speed gates runs it down, and until it reaches zero the estimate can only fall toward the intake air temperature. Effect: raise = the stored ambient val...</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x35F5E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5D8" flags="0x30">
    <title>Cruise Control - Accelerate Rate vs Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control. How fast the cruise target speed rises while cruise is accelerating from the resume / accelerate switch, by vehicle speed (applied every 100 ms up to the highest cruise speed). Stock 4.1 km/h per s at 38 km/h falling to 2.3 km/h per s from about 127 km/h. Effect: raise = cruise accelerates faster at that speed Evidence: ledger:E1353</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.9" />
      <LABEL index="2" value="55.8" />
      <LABEL index="3" value="64.6" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.4" />
      <LABEL index="6" value="91.2" />
      <LABEL index="7" value="100.1" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.9" />
      <LABEL index="10" value="126.8" />
      <LABEL index="11" value="135.6" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.4" />
      <LABEL index="14" value="162.2" />
      <LABEL index="15" value="171.1" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21A60" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per s</units>
      <decimalpl>2</decimalpl>
      <min>-2560.000000</min>
      <max>2559.921875</max>
      <MATH equation="X/12.8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5D9" flags="0x30">
    <title>Cruise Control - Resume Rate vs Distance Below Set Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control. How fast the cruise target speed rises while cruise brings the vehicle back up to the set speed, by how far below the set speed it is (applied every 100 ms; at the set speed cruise goes back to holding). Stock 3.5 km/h per s from 70 to about 44 km/h below, easing to 0.6 km/h per s close to the set speed. Effect: raise = cruise returns to the set speed faster from that far below Evidence: ledger:E0488, ledger:E1353</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (speed minus set speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-70" />
      <LABEL index="1" value="-65.6" />
      <LABEL index="2" value="-61.2" />
      <LABEL index="3" value="-56.9" />
      <LABEL index="4" value="-52.5" />
      <LABEL index="5" value="-48.1" />
      <LABEL index="6" value="-43.8" />
      <LABEL index="7" value="-39.4" />
      <LABEL index="8" value="-35" />
      <LABEL index="9" value="-30.6" />
      <LABEL index="10" value="-26.2" />
      <LABEL index="11" value="-21.9" />
      <LABEL index="12" value="-17.5" />
      <LABEL index="13" value="-13.1" />
      <LABEL index="14" value="-8.8" />
      <LABEL index="15" value="-4.4" />
      <LABEL index="16" value="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21A84" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h per s</units>
      <decimalpl>2</decimalpl>
      <min>-2560.000000</min>
      <max>2559.921875</max>
      <MATH equation="X/12.8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5DA" flags="0x0">
    <title>Cold Start Emission Monitor - Coolant Latch Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this coolant temperature the monitor keeps the highest coolant temperature seen and looks up the expected idle speed with it; at or above it the current coolant temperature is used (stock minus 39 C). Part of the cold start emission monitor (fault code P1400), which checks that the engine runs the warm-up idle speed and spark timing after a cold start. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0493, ledger:E1360</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34F44" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5DB" flags="0x0">
    <title>Cold Start Emission Monitor - Expected Idle Speed, Vehicle Speed Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The expected idle speed is set only while vehicle speed is below this value (and throttle below its own limit); otherwise it is set to zero (stock 2 km/h). Part of the cold start emission monitor (fault code P1400), which checks that the engine runs the warm-up idle speed and spark timing after a cold start. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0493, ledger:E1360</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34EF0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5DC" flags="0x0">
    <title>Cold Start Emission Monitor - Expected Idle Speed, Throttle Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The expected idle speed is set only while throttle is below this value (and vehicle speed below its own limit); otherwise it is set to zero (stock 2 %). Part of the cold start emission monitor (fault code P1400), which checks that the engine runs the warm-up idle speed and spark timing after a cold start. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0493, ledger:E1360</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x34EF2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5DD" flags="0x30">
    <title>Injector Circuit Fault Code by Cylinder Slot (reference)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Internal fault list index the injector circuit check reports for each cylinder slot: slots 1 to 5 report P0201, P0203, P0205, P0204 and P0202. Slots 6 to 8 are 0 (the H3 has 5 cylinders). Reference only: DO NOT EDIT. Effect: DO NOT EDIT (changes which fault code each injector reports) Evidence: ledger:E1366</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>cylinder slot</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38676" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fault index</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5DE" flags="0x0">
    <title>Port Temperature Model Target - Engine Speed Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target temperature added per rpm of engine speed. Stock 0.0126 C per rpm. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = hotter target at higher engine speed Evidence: ledger:E1371</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2B5E0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC per rpm</units>
    <decimalpl>4</decimalpl>
    <min>-1.000000</min>
    <max>0.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5DF" flags="0x0">
    <title>Port Temperature Model Target - Manifold Pressure Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target temperature added per kPa of manifold pressure. Stock -0.150 C per kPa. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = hotter target at higher manifold pressure Evidence: ledger:E1371</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2B5E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC per kPa</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5E0" flags="0x0">
    <title>Port Temperature Model Target - Air-Fuel Ratio Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target temperature added per unit of effective air-fuel ratio (the average of the commanded air-fuel ratio and the Air-Fuel Ratio Offset). Stock 106.3 C per AFR. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = hotter target at leaner air-fuel ratio Evidence: ledger:E1371</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2B5E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC per AFR</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5E1" flags="0x0">
    <title>Port Temperature Model Target - Air-Fuel Ratio Squared Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target temperature added per unit of effective air-fuel ratio squared. Stock -6.36 C. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = hotter target, more so at leaner air-fuel ratio Evidence: ledger:E1371</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2B5E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC per AFR squared</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5E2" flags="0x0">
    <title>Port Temperature Model Target - Spark Retard Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target temperature added per degree of spark retard from best torque timing (the torque model&#x27;s optimal spark minus actual spark, zero when not retarded). Stock -1.64 C per degree. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = hotter target with spark retard Evidence: ledger:E1371</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2B5E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC per deg</units>
    <decimalpl>0</decimalpl>
    <min>-4.000000</min>
    <max>3.999878</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8192"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5E3" flags="0x0">
    <title>Port Temperature Model Target - Coolant Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target temperature added per degree of coolant temperature. Stock 1.035. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = hotter target with a hotter engine Evidence: ledger:E1371</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2B5EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC per degC</units>
    <decimalpl>4</decimalpl>
    <min>-2.000000</min>
    <max>1.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5E4" flags="0x0">
    <title>Port Temperature Model Target - Constant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Constant added to the target temperature. Stock -317.7 C. The port temperature model estimates the intake port wall temperature the transient fuel (wall wetting) compensation uses: while the engine runs, the modelled temperature moves toward a target built as a weighted sum of engine speed, manifold pressure, commanded air-fuel ratio (and its square), spark retard from best torque timing, coolant temperature and a constant. Effect: raise = hotter target everywhere Evidence: ledger:E1371</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2B5EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-1024.000000</min>
    <max>1023.968750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5E5" flags="0x0">
    <title>Injector Circuit Test - Voltage OK Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The injector circuit fault checks (P0201 to P0205) start once system voltage has stayed above the Injector Circuit Test - System Voltage Minimum for longer than this. Stock 5.0 s. Effect: raise = the injector circuit checks wait longer after voltage recovers Evidence: ledger:E1372</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38670" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5E6" flags="0x0">
    <title>DFCO - Catalyst Hot Keep Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the catalyst-hot state is set it is kept while the catalyst model temperature stays at or above this (stock 0 C: kept until the next fuel cut request). Deceleration fuel cut (DFCO): once all the fuel cut conditions hold, fuel is cut only after this delay; the delay restarts whenever the conditions drop out or the gear changes. The catalyst-hot state is set when the catalyst model temperature reaches the hot temperature and lasts until the next fuel cut request. Effect: raise = the short delay ends when the catalyst cools below this Evidence: ledger:E0415, ledger:E1382</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F154" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5E7" flags="0x0">
    <title>DFCO - Entry Delay, Catalyst Hot</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel cut delay used while the catalyst is hot (stock 3 s). Deceleration fuel cut (DFCO): once all the fuel cut conditions hold, fuel is cut only after this delay; the delay restarts whenever the conditions drop out or the gear changes. The catalyst-hot state is set when the catalyst model temperature reaches the hot temperature and lasts until the next fuel cut request. Effect: lower = fuel is cut sooner on deceleration with a hot catalyst Evidence: ledger:E0415, ledger:E1382</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x2F176" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x5E8" flags="0x30">
    <title>DFCO - Entry Delay by Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel cut delay by gear (stock 11 s in 1st, 3 s in 2nd, 6 s in 3rd, 8 s in 4th). Deceleration fuel cut (DFCO): once all the fuel cut conditions hold, fuel is cut only after this delay; the delay restarts whenever the conditions drop out or the gear changes. Effect: lower = fuel is cut sooner on deceleration in that gear Evidence: ledger:E0415, ledger:E1382</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>gear (trans state 0..5)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1st" />
      <LABEL index="1" value="2nd" />
      <LABEL index="2" value="3rd" />
      <LABEL index="3" value="4th" />
      <LABEL index="4" value="5th" />
      <LABEL index="5" value="6th" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F178" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5E9" flags="0x30">
    <title>Pre-Sync Start Pulses - Start Delay vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once cranking arms the sequence, the pulses start after this time (stock 0 s). Pre-sync start pulses: an optional sequence of fuel pulses at cranking, before the PCM has synchronised to the crankshaft. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration (raise = later start pulses) Evidence: ledger:E1387</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x26E1C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24A08" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5EA" flags="0x30">
    <title>Fuel Cut List - 1 Cylinder (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the PCM cuts fuel to 1 cylinder, these are the injector outputs it switches off (0 = the first output). Stock: outputs 0 to 0. Used by the cylinder cut feature that runs the engine on fewer cylinders. Reference only: DO NOT EDIT. Effect: reference only (which injectors a cylinder cut turns off) Evidence: ledger:E1398</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>1</indexcount>
      <units>list position</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x265DE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="1" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>injector output</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5EB" flags="0x30">
    <title>Fuel Cut List - 2 Cylinders (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the PCM cuts fuel to 2 cylinders, these are the injector outputs it switches off (0 = the first output). Stock: outputs 0 to 1. Used by the cylinder cut feature that runs the engine on fewer cylinders. Reference only: DO NOT EDIT. Effect: reference only (which injectors a cylinder cut turns off) Evidence: ledger:E1398</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>list position</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x265E0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>injector output</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5EC" flags="0x30">
    <title>Fuel Cut List - 3 Cylinders (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the PCM cuts fuel to 3 cylinders, these are the injector outputs it switches off (0 = the first output). Stock: outputs 0 to 2. Used by the cylinder cut feature that runs the engine on fewer cylinders. Reference only: DO NOT EDIT. Effect: reference only (which injectors a cylinder cut turns off) Evidence: ledger:E1398</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>list position</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x265E4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>injector output</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5ED" flags="0x30">
    <title>Fuel Cut List - 4 Cylinders (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the PCM cuts fuel to 4 cylinders, these are the injector outputs it switches off (0 = the first output). Stock: outputs 0 to 3. Used by the cylinder cut feature that runs the engine on fewer cylinders. Reference only: DO NOT EDIT. Effect: reference only (which injectors a cylinder cut turns off) Evidence: ledger:E1398</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>list position</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x265EA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>injector output</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5EE" flags="0x30">
    <title>Fuel Cut List - 5 Cylinders (DO NOT EDIT, not used on this engine)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the PCM cuts fuel to 5 cylinders, these are the injector outputs it switches off (0 = the first output). Stock: outputs 0 to 4. This engine has five cylinders and cuts all five without a list, so this list is not used (dormant). Reference only: DO NOT EDIT. Effect: reference only (which injectors a cylinder cut turns off) Evidence: ledger:E1398</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>list position</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x265F2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>injector output</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5EF" flags="0x30">
    <title>Fuel Cut List - 6 Cylinders (DO NOT EDIT, not used on this engine)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the PCM cuts fuel to 6 cylinders, these are the injector outputs it switches off (0 = the first output). Stock: outputs 0 to 5. This engine has five cylinders and cuts all five without a list, so this list is not used (dormant). Reference only: DO NOT EDIT. Effect: reference only (which injectors a cylinder cut turns off) Evidence: ledger:E1398</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>6</indexcount>
      <units>list position</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x265FC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="6" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>injector output</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5F0" flags="0x30">
    <title>Fuel Cut List - 7 Cylinders (DO NOT EDIT, not used on this engine)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the PCM cuts fuel to 7 cylinders, these are the injector outputs it switches off (0 = the first output). Stock: outputs 0 to 6. This engine has five cylinders and cuts all five without a list, so this list is not used (dormant). Reference only: DO NOT EDIT. Effect: reference only (which injectors a cylinder cut turns off) Evidence: ledger:E1398</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>list position</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26608" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>injector output</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5F1" flags="0x30">
    <title>Misfire Detection - Signal Factor vs Throttle Closing Rate, Cylinder Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire detection (cylinder mode): factor applied to the misfire signal by how fast the throttle is closing (largest change of the commanded throttle per 50 ms, 0 to 100 %). The lowest factor of the last three updates of the closing and opening curves is used, and never more than 1.0, so values above 1.0 have no effect. Below 1.0 the signal is reduced, which makes misfire detection less sensitive during throttle transients. Stock 1.0 everywhere. Effect: lower = misfire detection is less sensitive while the throttle is closing that fast Evidence: ledger:E0670, ledger:E0936, ledger:E0999, ledger:E1075, ledger:E1409</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% per 50 ms</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x396D6" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>-16.000000</min>
      <max>15.999512</max>
      <MATH equation="X/2048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5F2" flags="0x30">
    <title>Misfire Detection - Signal Factor vs Throttle Opening Rate, Cylinder Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire detection (cylinder mode): factor applied to the misfire signal by how fast the throttle is opening (largest change of the commanded throttle per 50 ms, 0 to 100 %). The lowest factor of the last three updates of the closing and opening curves is used, and never more than 1.0, so values above 1.0 have no effect. Below 1.0 the signal is reduced, which makes misfire detection less sensitive during throttle transients. Stock 1.0 everywhere. Effect: lower = misfire detection is less sensitive while the throttle is opening that fast Evidence: ledger:E0670, ledger:E0936, ledger:E0999, ledger:E1075, ledger:E1409</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% per 50 ms</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x396FA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>-16.000000</min>
      <max>15.999512</max>
      <MATH equation="X/2048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5F3" flags="0x30">
    <title>Misfire Detection - Signal Factor vs Throttle Closing Rate, Revolution Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire detection (revolution mode): factor applied to the misfire signal by how fast the throttle is closing (largest change of the commanded throttle per 50 ms, 0 to 100 %). The lowest factor of the last three updates of the closing and opening curves is used, and never more than 1.0, so values above 1.0 have no effect. Below 1.0 the signal is reduced, which makes misfire detection less sensitive during throttle transients. Stock 1.0 everywhere. Effect: lower = misfire detection is less sensitive while the throttle is closing that fast Evidence: ledger:E0670, ledger:E0936, ledger:E0999, ledger:E1075, ledger:E1409</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% per 50 ms</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3971E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>-16.000000</min>
      <max>15.999512</max>
      <MATH equation="X/2048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x5F4" flags="0x30">
    <title>Misfire Detection - Signal Factor vs Throttle Opening Rate, Revolution Mode</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire detection (revolution mode): factor applied to the misfire signal by how fast the throttle is opening (largest change of the commanded throttle per 50 ms, 0 to 100 %). The lowest factor of the last three updates of the closing and opening curves is used, and never more than 1.0, so values above 1.0 have no effect. Below 1.0 the signal is reduced, which makes misfire detection less sensitive during throttle transients. Stock 1.0 everywhere. Effect: lower = misfire detection is less sensitive while the throttle is opening that fast Evidence: ledger:E0670, ledger:E0936, ledger:E0999, ledger:E1075, ledger:E1409</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>% per 50 ms</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x39742" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>factor</units>
      <decimalpl>2</decimalpl>
      <min>-16.000000</min>
      <max>15.999512</max>
      <MATH equation="X/2048"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x5F5" flags="0x0">
    <title>Traction Control Gear Request - Minimum Throttle Area (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control gear request: an active request is cancelled when the driver throttle area falls below this (stock 20 %). On this calibration the gear request is not applied to the shift schedule (inactive). Effect: no effect on this truck (lower = the request survives a smaller throttle opening) Evidence: ledger:E0269, ledger:E0436, ledger:E0925, ledger:E1412</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x302AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5F6" flags="0x0">
    <title>Traction Control Gear Request - Maximum Throttle Rise (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control gear request: an active request is cancelled when the driver throttle area rises faster than this (stock 20 % per 25 ms). On this calibration the gear request is not applied to the shift schedule (inactive). Effect: no effect on this truck (raise = the request survives a faster tip-in) Evidence: ledger:E0269, ledger:E0436, ledger:E0925, ledger:E1412</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x302AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% per 25 ms</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5F7" flags="0x0">
    <title>Traction Control Gear Request - Hold Time, 3rd Gear (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control gear request: time a 3rd gear request is held before it steps down to 2nd (stock 5 s). On this calibration the gear request is not applied to the shift schedule (inactive). Effect: no effect on this truck (raise = a 3rd gear request lasts longer) Evidence: ledger:E0269, ledger:E0436, ledger:E0925, ledger:E1412</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x302AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5F8" flags="0x0">
    <title>Traction Control Gear Request - Hold Time, 2nd Gear (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control gear request: time a 2nd gear request is held before it steps down to 1st (stock 1 s). On this calibration the gear request is not applied to the shift schedule (inactive). Effect: no effect on this truck (raise = a 2nd gear request lasts longer) Evidence: ledger:E0269, ledger:E0436, ledger:E0925, ledger:E1412</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x302B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5F9" flags="0x0">
    <title>Traction Control Gear Request - Hold Time, 1st Gear (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Traction control gear request: time a 1st gear request is held before the request ends (stock 1 s). On this calibration the gear request is not applied to the shift schedule (inactive). Effect: no effect on this truck (raise = a 1st gear request lasts longer) Evidence: ledger:E0269, ledger:E0436, ledger:E0925, ledger:E1412</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x302B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5FA" flags="0x0">
    <title>VE Transient Mode - Window Entry Length (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of model updates the summed manifold pressure change is collected before the window starts again while the transient mode is off (stock 4). Part of the window check of the volumetric efficiency transient mode, which runs only when its throttle gate is open; on the stock calibration that gate is closed, so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E1429</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C98C" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5FB" flags="0x0">
    <title>VE Transient Mode - Window Exit Pressure Sum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While the transient mode is on, it ends when a full window has passed and the manifold pressure change from the window start, summed over the window&#x27;s updates, is below this (stock 1.5 kPa). Part of the window check of the volumetric efficiency transient mode, which runs only when its throttle gate is open; on the stock calibration that gate is closed, so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E1429</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C996" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5FC" flags="0x0">
    <title>Engine Oil Pressure - Broadcast Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The engine oil pressure the PCM sends on the vehicle bus is a filtered copy of its oil pressure value (the estimate on stock, or the sensor reading with the sensor path on): each update moves it this fraction of the way to the new value. Stock 0.10. Effect: raise = the broadcast oil pressure follows changes faster Evidence: ledger:E1430, ledger:E1831</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x225E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5FD" flags="0x0">
    <title>Crank and Cam Signal Loss Watchdog A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When no crank reference event has arrived for this long, the measured reference period is set to its maximum (engine speed from it reads zero) and the reference tracking is reset. Companion of Watchdog B. Stock 0.8 s. Effect: raise = a lost crank signal is noticed later Evidence: ledger:E1430</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x22CB2" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5FE" flags="0x0">
    <title>Ambient Air Temp Estimate - Run Time Before Rise</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine run time, added up over the drives since the estimate was last reset, that must pass before the ambient air temperature estimate may rise toward the intake air temperature; until then it can only fall. It works together with the flush requirement after a hot soak. Stock 100 s. Effect: raise = the ambient estimate stays low for longer after a hot restart Evidence: ledger:E0385, ledger:E1184, ledger:E1334, ledger:E1431</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x35F5C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x5FF" flags="0x0">
    <title>EVAP Test - Start-Up Coolant Minus Intake Air, Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest difference between start-up coolant and start-up intake air temperature (stock 6.7 C): the engine must have cooled down to near air temperature. Run condition of the engine-running EVAP test (large leak, purge flow and vent checks). Effect: raise = the test also runs after a shorter cool-down Evidence: ledger:E0769, ledger:E1072, ledger:E1434</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371D6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x600" flags="0x0">
    <title>EVAP Test - Start-Up Coolant Window, Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest start-up coolant temperature for the test (stock 35 C). The same window applies to ambient air temperature for a related condition. Run condition of the engine-running EVAP test (large leak, purge flow and vent checks). Effect: raise = the test runs after warmer starts Evidence: ledger:E0769, ledger:E1072, ledger:E1434</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371D8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x601" flags="0x0">
    <title>EVAP Test - Start-Up Coolant Window, Min</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest start-up coolant temperature for the test (stock 4.4 C). The same window applies to ambient air temperature for a related condition. Run condition of the engine-running EVAP test (large leak, purge flow and vent checks). Effect: lower = the test runs after colder starts Evidence: ledger:E0769, ledger:E1072, ledger:E1434</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371DA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x602" flags="0x0">
    <title>Tank Pressure Zero - Cold Soak Coolant Minus Intake Air, Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest start-up coolant minus intake air difference that counts as a cold soak (stock 8 C). The tank pressure zero check is only kept after a cold soak, with intake air below its maximum; otherwise it is cancelled. Effect: raise = more starts count as a cold soak (the zero check runs more often) Evidence: ledger:E0769, ledger:E1072, ledger:E1434</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x603" flags="0x0">
    <title>EVAP Test - Standstill Speed, Max</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed at or below which the engine-running EVAP test counts the vehicle as stopped (stock 5 km/h); above it the test&#x27;s standstill timer restarts. Effect: raise = the vehicle counts as stopped at a higher speed Evidence: ledger:E0769, ledger:E1435</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x604" flags="0x30">
    <title>Idle A/C - Clutch Handshake Airflow Adder vs Compressor Torque</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added at an A/C clutch release or engagement, by A/C compressor torque (0 to 80 Nm), per gear state and event. The value is multiplied by the A/C Idle Air rpm factor, 0.125 at every engine speed on stock; the scaling shown includes that factor (as for A/C Idle Air - Target). Stock 0 in every cell, so no adder is applied on the stock calibration. When the A/C compressor clutch releases or engages at idle, an extra idle airflow is added for the A/C idle adder hold time and then decays away. Effect: raise = more idle air...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="MARKER" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>4</indexcount>
      <units>event</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="In Gear, clutch release" />
      <LABEL index="1" value="In Gear, clutch engage" />
      <LABEL index="2" value="Park / Neutral, clutch release" />
      <LABEL index="3" value="Park / Neutral, clutch engage" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29BD8" mmedelementsizebits="16" mmedrowcount="4" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>0</decimalpl>
      <min>-4.000000</min>
      <max>3.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x605" flags="0x30">
    <title>Idle A/C - Clutch Handshake Adder Decay Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After the hold time, the clutch handshake adder shrinks by this fraction of itself each update until it reaches zero. Stock 0.10 for both events; the adder itself is zero on the stock calibration, so this has no effect on the stock calibration (dormant). When the A/C compressor clutch releases or engages at idle, an extra idle airflow is added for the A/C idle adder hold time and then decays away. Effect: no effect on the stock calibration (raise = the adder fades faster) Evidence: ledger:E1436</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>event</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="A/C clutch release" />
      <LABEL index="1" value="A/C clutch engage" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29BD4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x606" flags="0x0">
    <title>Traction Control Gear Request - Arming Throttle Area, Cold Engine</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In the cold engine case the arming timer runs up while the driver throttle area is above this (stock 20 %), and runs back down otherwise. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0505, ledger:E0921, ledger:E0925, ledger:E1114, ledger:E1440</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30296" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x607" flags="0x0">
    <title>Traction Control Gear Request - Arming Throttle Area</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Otherwise the arming timer runs up while traction control is reducing torque and the driver throttle area is above this (stock 40 %), and runs back down otherwise. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0505, ledger:E0921, ledger:E0925, ledger:E1114, ledger:E1440</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30298" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x608" flags="0x0">
    <title>Traction Control Gear Request - Arming Time, Cold Engine</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Arming time used in the cold engine case (stock 3.8 s). Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on this truck Evidence: ledger:E0506, ledger:E0925, ledger:E1114, ledger:E1440</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3029C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x609" flags="0x0">
    <title>EVAP Test - Purge Limit During Vent Check</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine-running EVAP test: commanded evaporative purge is limited to this while the test holds the vent open for the vent restriction check (P0446) before its purge volume count starts, and in one later test state while the matching option word is set (set on stock). Stock 15 %. Effect: raise = more purge is allowed during those test steps Evidence: ledger:E0446, ledger:E0775, ledger:E0930, ledger:E1456</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3735E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.781250</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/326.4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x60A" flags="0x30">
    <title>Throttle Torque Control - Engine Speed Term Gain vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Gain applied to the engine speed term of the throttle torque controller&#x27;s input, by filtered engine speed (stock 0.60 up to 500 rpm rising to 0.96 at 8000 rpm). Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0614, ledger:E1149, ledger:E1465</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="500" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1500" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2500" />
      <LABEL index="6" value="3000" />
      <LABEL index="7" value="3500" />
      <LABEL index="8" value="4000" />
      <LABEL index="9" value="4500" />
      <LABEL index="10" value="5000" />
      <LABEL index="11" value="5500" />
      <LABEL index="12" value="6000" />
      <LABEL index="13" value="6500" />
      <LABEL index="14" value="7000" />
      <LABEL index="15" value="7500" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21152" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x60B" flags="0x0">
    <title>Throttle Torque Control - Engine Speed Filter Gain (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain for the engine speed the torque controller&#x27;s speed term uses (stock 0.9 per update). Part of the electronic throttle torque controller, which is switched off on this calibration: no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E0614, ledger:E1149, ledger:E1465</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2114C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x60C" flags="0x0">
    <title>Corrected Coolant - Cold Correction Off Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The corrected coolant temperature the PCM uses for its coolant model, oil life, torque friction and other functions equals the measured coolant above this temperature. At or below it, it is pulled toward the intake air temperature (see Corrected Coolant - Pull Toward Intake Air). Stock 75 C. Effect: raise = the cold correction applies up to a warmer coolant temperature Evidence: ledger:E1477</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x22BFE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x60D" flags="0x0">
    <title>Corrected Coolant - Pull Toward Intake Air</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At or below the cold correction temperature, the corrected coolant temperature is the measured coolant minus this share of (coolant - intake air temperature), only when the intake air is colder. Stock 0.62. Effect: raise = the corrected coolant reads closer to the intake air temperature on a cold engine Evidence: ledger:E1477</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x22C00" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x60E" flags="0x0">
    <title>O2 Response Test Credit - Airflow Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The credit grows only while mass airflow is at or above this (stock 20 g/s), with the throttle, engine speed and manifold pressure minimums also met. Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x361F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x60F" flags="0x0">
    <title>O2 Response Test Credit - Engine Speed Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The credit grows only while engine speed is at or above this (stock 1500 rpm). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36202" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x610" flags="0x0">
    <title>O2 Response Test Credit - Throttle Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The credit grows only while throttle position, with the share used for idle air taken out, is at or above this (stock 5 %). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x361FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x611" flags="0x0">
    <title>O2 Response Test Credit - Manifold Pressure Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The credit grows only while manifold pressure is at or above this (stock 30 kPa). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36274" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x612" flags="0x0">
    <title>O2 Response Test Credit - Stopped Idle Time Limit (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After the throttle has been closed with the vehicle stopped for longer than this, the credit falls each update (stock 5 s). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36210" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x613" flags="0x0">
    <title>O2 Response Test Credit - Closed Throttle Coast Time Limit (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After the throttle has been closed with the vehicle moving for longer than this, the credit falls each update (stock 5 s). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36212" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x614" flags="0x0">
    <title>O2 Response Test Credit - Step Down, Cylinders Not Fuelled (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Credit taken off each update while not every cylinder is being fuelled (stock 3). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36216" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x615" flags="0x0">
    <title>O2 Response Test Credit - Step Down, Stopped Idle (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Credit taken off each update after the stopped idle time limit (stock 1). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36218" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x616" flags="0x0">
    <title>O2 Response Test Credit - Step Down, Closed Throttle Coast (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Credit taken off each update after the closed throttle coast time limit (stock 1). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3621A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x617" flags="0x0">
    <title>O2 Response Test Credit - Step Up (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Credit added each update while every minimum is met (stock 3). Part of the drive credit of the O2 sensor response test: the test may sample only while the credit is at or above its minimum. On the stock calibration that minimum is 0, so the credit never blocks the test (dormant). Effect: no effect on this truck Evidence: ledger:E0217, ledger:E0300, ledger:E0769, ledger:E1502</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3621C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x618" flags="0x0">
    <title>Airflow Mode 2 Entry Window A - Engine Speed Maximum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window A allows the mode up to this engine speed (scaled by the intake air temperature factor). Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C998" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x619" flags="0x0">
    <title>Airflow Mode 2 Entry Window B - Engine Speed Maximum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window B allows the mode up to this engine speed (scaled by the intake air temperature factor). Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C99A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x61A" flags="0x0">
    <title>Airflow Mode 2 Entry Window A - Engine Speed Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window A allows the mode only above this engine speed (scaled by the intake air temperature factor). Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C99C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x61B" flags="0x0">
    <title>Airflow Mode 2 Entry Window B - Engine Speed Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window B allows the mode only above this engine speed (scaled by the intake air temperature factor). Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C99E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x61C" flags="0x0">
    <title>Airflow Mode 2 Entry Engine Speed Hysteresis (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the mode is on, both engine speed windows are widened by this on each side before it ends. Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C9A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x61D" flags="0x0">
    <title>Airflow Mode 2 Entry Window A - Throttle Area Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window A allows the mode only at or above this throttle area. Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C9A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x61E" flags="0x0">
    <title>Airflow Mode 2 Entry Window B - Throttle Area Minimum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window B allows the mode only at or above this throttle area. Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C9A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x61F" flags="0x0">
    <title>Airflow Mode 2 Entry Throttle Area Hysteresis (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the mode is on, both throttle area minimums are lowered by this before it ends. Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C9A6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.675"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x620" flags="0x0">
    <title>Airflow Mode 2 Entry Window A - Manifold Vacuum Maximum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window A allows the mode only while manifold vacuum (barometric minus manifold pressure) is at or below this. Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C9A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x621" flags="0x0">
    <title>Airflow Mode 2 Entry Window B - Manifold Vacuum Maximum (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Window B allows the mode only while manifold vacuum (barometric minus manifold pressure) is at or below this. Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C9AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x622" flags="0x0">
    <title>Airflow Mode 2 Entry Manifold Vacuum Hysteresis (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the mode is on, both vacuum maximums are raised by this before it ends. Stock 0. Part of the entry check of the throttle-area airflow mode, which the stock calibration can never enter (every window value is zero), so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0735, ledger:E0863, ledger:E1504</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C9AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x623" flags="0x30">
    <title>Idle RPM Event - Airflow Adder (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added during the hold time of an rpm event. Row 1 In Gear, row 2 Park / Neutral; column rise / drop. Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1505</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>event</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="rise" />
      <LABEL index="1" value="drop" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>transmission</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="In Gear" />
      <LABEL index="1" value="Park / Neutral" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AB24" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x624" flags="0x30">
    <title>Idle RPM Event - Adder Decay Rate (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After the hold time the adder shrinks by this fraction of itself each update; 0 ends it at once. Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1505</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>event</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="rise" />
      <LABEL index="1" value="drop" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AB2C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x625" flags="0x30">
    <title>Idle RPM Event - Learn Pause Time After Decay (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After the adder has decayed, the idle airflow integral and learning stay paused for this long. Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1505</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>event</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="rise" />
      <LABEL index="1" value="drop" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AB30" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x626" flags="0x30">
    <title>Idle RPM Event - Adder Hold Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the event airflow adder is held before it decays. Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1505</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>event</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="rise" />
      <LABEL index="1" value="drop" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AB34" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x627" flags="0x0">
    <title>Idle RPM Event - Engine Speed Margin Above Desired Idle (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The event sequence only continues while engine speed is below desired idle plus this. Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1505</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2AB38" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x628" flags="0x0">
    <title>Idle RPM Event - Vehicle Speed Below (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The event sequence only continues while vehicle speed is below this. Stock 0: never. Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1505</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2AB3A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x629" flags="0x0">
    <title>Idle RPM Event - Minimum Time Since Last Event (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A new event of the same direction only starts the adder when this long has passed since the last one. Idle rpm change event: when idle speed rises or falls by more than a threshold in one 12.5 ms update, the idle airflow integral and learning pause and, after a confirm step, an extra idle airflow is added for a hold time and then decays. Every value is 0 on the stock calibration and the speed limit of 0 stops every sequence, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1505</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2AB3C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x62A" flags="0x0">
    <title>Idle Cold Request - Desired Idle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Desired idle requested while the cold idle request is active. Stock 550 rpm. Cold idle request: until the engine coolant has reached the limit at least once since start, desired idle is raised to at least the request speed (desired idle is the highest of all idle speed requests). Effect: raise = higher idle speed in a cold engine until the coolant limit is reached Evidence: ledger:E1508</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x2B088" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x62B" flags="0x30">
    <title>Idle Altitude Up - Desired Idle Adder</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to desired idle while the altitude idle-up is active. Stock 0. Altitude idle-up: at low barometric pressure (below Idle Altitude Up Baro) with coolant below the limit, desired idle is raised by the altitude adder. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1508</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>transmission</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="In Gear" />
      <LABEL index="1" value="Park / Neutral" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AB88" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x62C" flags="0x0">
    <title>Pedal Sensor 1 Circuit Test - Voltage High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal position sensor 1 reads as out of range (P2122 / P2123) above this voltage. Stock 4.68 V. Effect: widening the range = a faulty pedal sensor signal is caught later Evidence: ledger:E1512</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DD8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.999924</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13107.2"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x62D" flags="0x0">
    <title>Pedal Sensor 1 Circuit Test - Voltage Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal position sensor 1 reads as out of range (P2122 / P2123) below this voltage. Stock 0.75 V. Effect: widening the range = a faulty pedal sensor signal is caught later Evidence: ledger:E1512</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DDA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.999924</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13107.2"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x62E" flags="0x0">
    <title>Pedal Sensor 2 Circuit Test - Voltage Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal position sensor 2 reads as out of range (P2127 / P2128) below this voltage. Stock 2.60 V. Effect: widening the range = a faulty pedal sensor signal is caught later Evidence: ledger:E1512</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DE2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.999924</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13107.2"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x62F" flags="0x0">
    <title>Pedal Sensor 2 Circuit Test - Voltage High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Accelerator pedal position sensor 2 reads as out of range (P2127 / P2128) above this voltage. Stock 4.68 V. Effect: widening the range = a faulty pedal sensor signal is caught later Evidence: ledger:E1512</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DF6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>4.999924</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13107.2"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x630" flags="0x0">
    <title>Pedal Sensor 1 Circuit Test - Out of Range Time in Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal sensor 1 circuit fault when the sensor has been out of range for this long in total within one test window (time in 12.5 ms steps). Stock 0.25 s. Effect: raise = more out-of-range time is tolerated before the fault Evidence: ledger:E1515</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DDC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>819.187500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/80"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x631" flags="0x0">
    <title>Pedal Sensor 1 Circuit Test - Continuous Out of Range Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal sensor 1 circuit fault when the sensor stays out of range for this long without a break (time in 12.5 ms steps). Stock 0.125 s. Effect: raise = a longer continuous out-of-range reading is tolerated Evidence: ledger:E1515</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DDE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>819.187500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/80"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x632" flags="0x0">
    <title>Pedal Sensor 1 Circuit Test - Window Length</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Length of the test window that starts at the first out-of-range reading; if the accumulated limit is not reached by then, the counts restart (time in 12.5 ms steps). Stock 0.5 s. Effect: raise = intermittent out-of-range readings are collected over a longer time Evidence: ledger:E1515</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DE0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>819.187500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/80"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x633" flags="0x0">
    <title>Pedal Sensor 2 Circuit Test - Out of Range Time in Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal sensor 2 circuit fault when the sensor has been out of range for this long in total within one test window (time in 12.5 ms steps). Stock 0.19 s. Effect: raise = more out-of-range time is tolerated before the fault Evidence: ledger:E1515</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DE6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>819.187500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/80"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x634" flags="0x0">
    <title>Pedal Sensor 2 Circuit Test - Continuous Out of Range Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal sensor 2 circuit fault when the sensor stays out of range for this long without a break (time in 12.5 ms steps). Stock 0.125 s. Effect: raise = a longer continuous out-of-range reading is tolerated Evidence: ledger:E1515</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DE8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>819.187500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/80"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x635" flags="0x0">
    <title>Pedal Sensor 2 Circuit Test - Window Length</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Length of the test window that starts at the first out-of-range reading; if the accumulated limit is not reached by then, the counts restart (time in 12.5 ms steps). Stock 0.44 s. Effect: raise = intermittent out-of-range readings are collected over a longer time Evidence: ledger:E1515</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DEA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>819.187500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/80"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x636" flags="0x30">
    <title>Airmass Predictor - Blend Toward Prediction, Alternate Mode (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of the airmass predictor, the identified model that estimates cylinder airmass from recent MAF, MAP and throttle area samples, with one coefficient per operating region. Used in place of Blend Toward Prediction while the predictor&#x27;s alternate mode is active: fraction of the way from the prediction to the filtered MAF airmass that the airmass estimate takes (0 = prediction only, 1.0 = filtered MAF airmass only; stock 1.0 in every region, so in alternate mode the estimate follows the filtered MAF airmass). Engine-specific model data: reference only, DO NOT EDIT. Effect: reference only (airmass model) Evidence: ledger:...</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C95C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x637" flags="0x0">
    <title>Barometric Pressure - Default Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Barometric pressure the PCM assumes when its stored barometric reading is lost (memory check fails) and when the barometric estimate is reset; the estimate is then updated from manifold pressure. Stock 100 kPa. Effect: raise = a higher starting barometric pressure after a memory loss or reset Evidence: ledger:E1534</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x2124C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x638" flags="0x0">
    <title>Airmass Model - Load Airmass Capped Prediction Weight (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the start-up blend is complete, the load airmass is the predicted cylinder airmass moved this fraction of the way toward the prediction capped by the maximum airflow curve (0 = uncapped prediction, 1.0 = capped prediction; stock 0.83). Part of the cylinder airmass model; reference only, DO NOT EDIT. During the start-up blend both values move from the speed-density airmass to this blend. Effect: reference only (airmass model) Evidence: ledger:E1535</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C736" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction (1.0 = capped prediction only)</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x639" flags="0x0">
    <title>Airmass Model - Fuel Airmass Second Prediction Weight (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the start-up blend is complete, the airmass used for base fuel is the capped prediction moved this fraction of the way toward the predictor&#x27;s second output, also capped by the maximum airflow curve (stock 0.67). Part of the cylinder airmass model; reference only, DO NOT EDIT. During the start-up blend both values move from the speed-density airmass to this blend. Effect: reference only (airmass model) Evidence: ledger:E1535</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C738" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction (1.0 = second capped prediction only)</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x63A" flags="0x0">
    <title>Throttle Actuator Command - Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit on the commanded throttle actuator position: every update the throttle control clamps its command to this value. Stock 100.4 %, so it does not limit the stock calibration. Effect: lower = caps the throttle opening at this position Evidence: ledger:E1538</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x24182" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x63B" flags="0x0">
    <title>Throttle Actuator Command - Wide Open Status Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While the commanded throttle is at or above this, the PCM sets a wide-open bit in its throttle status reports (stock 98.4 %). Reporting only: the throttle command is not changed. Effect: reporting only Evidence: ledger:E1538</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x241AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x63C" flags="0x30">
    <title>Cam Sensor Performance - Minimum Edges per Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fewest cam edges per window that count as good (stock 475 / 275). Camshaft position sensor performance test (P0366 for cam input 1, P0341 for cam input 2): the cam edges counted in each test window must fall within the band; when enough windows fall outside it the code sets, otherwise the test passes after a set number of windows. Effect: raise = a cam signal that loses edges is flagged sooner Evidence: ledger:E1080, ledger:E1550</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3686C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>edges</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x63D" flags="0x30">
    <title>Cam Sensor Performance - Maximum Edges per Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most cam edges per window that count as good (stock 525 / 325). Camshaft position sensor performance test (P0366 for cam input 1, P0341 for cam input 2): the cam edges counted in each test window must fall within the band; when enough windows fall outside it the code sets, otherwise the test passes after a set number of windows. Effect: lower = a noisy cam signal with extra edges is flagged sooner Evidence: ledger:E1080, ledger:E1550</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36874" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>edges</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x63E" flags="0x30">
    <title>Cam Sensor Performance - Bad Windows to Fail</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Windows outside the band that set the code (stock 8). Camshaft position sensor performance test (P0366 for cam input 1, P0341 for cam input 2): the cam edges counted in each test window must fall within the band; when enough windows fall outside it the code sets, otherwise the test passes after a set number of windows. Effect: lower = the code sets after fewer bad windows Evidence: ledger:E1080, ledger:E1550</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3687C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>windows</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x63F" flags="0x30">
    <title>Cam Sensor Performance - Windows per Test</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Windows after which the test passes when fewer were bad (stock 10). Camshaft position sensor performance test (P0366 for cam input 1, P0341 for cam input 2): the cam edges counted in each test window must fall within the band; when enough windows fall outside it the code sets, otherwise the test passes after a set number of windows. Effect: raise = a longer test before a pass is reported Evidence: ledger:E1080, ledger:E1550</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36884" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>windows</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x640" flags="0x30">
    <title>Cam Sensor Performance - Window Length</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Length of one test window, in updates of the cam check, which runs with the crank position tasks (stock 1000). Camshaft position sensor performance test (P0366 for cam input 1, P0341 for cam input 2): the cam edges counted in each test window must fall within the band; when enough windows fall outside it the code sets, otherwise the test passes after a set number of windows. Effect: raise = longer windows, more edges per window (the band must be scaled with it) Evidence: ledger:E1080, ledger:E1550</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3688C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>updates</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x641" flags="0x0">
    <title>EVAP Test (Engine Running) - Wait Before Leak Check</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After the purge valve check, the engine-running EVAP test waits at least this long (with purge enabled and the purge factor above the required value) before it starts the leak pull-down. 0 = start at once when purge is already enabled. Stock 5 s. Effect: raise = the leak check starts later after the purge valve check Evidence: ledger:E1551</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3737E" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x642" flags="0x0">
    <title>EVAP Test (Engine Running) - Purge Factor Required for Leak Check</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The engine-running EVAP test starts its leak pull-down only once the canister purge factor (1.0 = full purge request) has reached this. Stock 0.5. Effect: raise = the leak check waits for more purge first Evidence: ledger:E1551</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3737A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x643" flags="0x0">
    <title>EVAP Test (Engine Running) - Time Allowed After Gross Leak Pass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Once the tank reaches the gross leak pass vacuum, the engine-running EVAP test may go on (vent check and the rest) for this long; after it the test stops for the rest of the trip. A failed gross leak check stops it at once. Stock 90 s. Effect: raise = the test gets longer to finish its remaining checks after the pull-down Evidence: ledger:E1552</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x24610" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>214748364.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x644" flags="0x30">
    <title>Cam Sensor Start-Up Check - Window Length</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Length of the start-up check window, in updates of the cam check counted from the arming update (stock 10). Camshaft position sensor start-up check (P0366 for cam input 1, P0341 for cam input 2): once armed, the cam edges counted in one window must fall within the band, otherwise the code sets; inside the band the check passes. It runs once. Effect: raise = a longer window, more edges expected (the band must be scaled with it) Evidence: ledger:E1080, ledger:E1553</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3682A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>updates</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x645" flags="0x30">
    <title>Cam Sensor Start-Up Check - Minimum Edges</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fewest cam edges in the window that pass (stock 4 / 2). Camshaft position sensor start-up check (P0366 for cam input 1, P0341 for cam input 2): once armed, the cam edges counted in one window must fall within the band, otherwise the code sets; inside the band the check passes. It runs once. Effect: raise = a cam signal that loses edges at start-up is flagged sooner Evidence: ledger:E1080, ledger:E1553</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36832" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>edges</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x646" flags="0x30">
    <title>Cam Sensor Start-Up Check - Maximum Edges</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most cam edges in the window that pass (stock 13 / 9). Camshaft position sensor start-up check (P0366 for cam input 1, P0341 for cam input 2): once armed, the cam edges counted in one window must fall within the band, otherwise the code sets; inside the band the check passes. It runs once. Effect: lower = a noisy cam signal at start-up is flagged sooner Evidence: ledger:E1080, ledger:E1553</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0366)" />
      <LABEL index="1" value="input 2 (P0341)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3683A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>edges</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x647" flags="0x30">
    <title>EVAP Test (Engine Running) - Pull-Down Time Allowance by Fuel Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time allowed in the test&#x27;s time budget for each pull-down, by fuel level (below 33 %, 33 to 67 %, above 67 %; the first when the fuel level reading is invalid). The test starts only if the time left covers its budget, and ends when the budget runs out. Stock 30 / 20 / 10 s. Engine-running EVAP test. Effect: raise = a longer budget (the test needs a longer window to start) Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>fuel level</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="below 33 %" />
      <LABEL index="1" value="33 to 67 %" />
      <LABEL index="2" value="above 67 %" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24608" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x648" flags="0x0">
    <title>EVAP Test (Engine Running) - Small Leak Decay Measurements</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of small leak decay measurements the test allows for; the time budget covers the ones still to go after the current one. Stock 3. Engine-running EVAP test. Effect: raise = a longer time budget Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3797E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x649" flags="0x0">
    <title>EVAP Test (Engine Running) - Pull-Down Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the small leak pull-down must hold the tank between the pass vacuum and the pull-down maximum; also a term of the time budget for each measurement. Stock 10 s. Engine-running EVAP test. Effect: raise = a longer hold and budget Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37980" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x64A" flags="0x0">
    <title>EVAP Test (Engine Running) - Minimum Decay Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Shortest decay time before a small leak decay is evaluated; also a term of the time budget for each measurement. Stock 5 s. Engine-running EVAP test. Effect: raise = a longer minimum decay and budget Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37982" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x64B" flags="0x0">
    <title>EVAP Test (Engine Running) - Pull-Down Give-Up Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the small leak pull-down may stay below the pass vacuum before it gives up. Stock 10 s. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37394" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x64C" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Vent-Down Vacuum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vapour check: after venting, tank vacuum must fall to this or below. Stock 2.0 inH2O. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3738C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x64D" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Vent-Down Time Limit (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vapour check: vacuum above the vent-down value for longer than this stops the test. Also a term of the time budget while the vapour check is pending. Stock 30 s. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37988" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x64E" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Settle Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vapour check: time at or below the vent-down vacuum before the pressure measurement stage. Also a budget term. Stock 15 s. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3798A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x64F" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Start Time Limit (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vapour check: if the start vacuum is not reached within this, the measurement is skipped. Also a budget term. Stock 30 s. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37986" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x650" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Measurement Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vapour check: length of the pressure rise measurement. Also a budget term. Stock 30 s. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37984" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x651" flags="0x0">
    <title>EVAP Test (Engine Running) - Gross Leak Volume Flow Deduction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Purge flow taken off the modelled purge flow before it is added up into the purged volume of the gross leak check (P0455 fails when the volume passes its limit before the tank reaches the pass vacuum). Stock 0 L/s. Engine-running EVAP test. Effect: raise = less volume counted per second (the gross leak check takes longer to fail) Evidence: ledger:E1555</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37396" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>L/s</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.124998</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/524288"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x652" flags="0x0">
    <title>EVAP Test (Engine Running) - Decay Early Evaluation Vacuum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Small leak decay: evaluated before its full time once tank vacuum falls below this. Stock 1.0 inH2O. Engine-running EVAP test. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1555</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37398" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x653" flags="0x0">
    <title>EVAP Test (Engine Running) - Decay Limit Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Small leak decay: multiplier on the decay slope limit from the limit tables. Stock 1.0. Engine-running EVAP test. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1555</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3739A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>3.999939</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16384"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x654" flags="0x0">
    <title>EVAP Test (Engine Running) - Decay Measurement Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Small leak decay: time after which the decay slope is evaluated. Stock 10 s. Engine-running EVAP test. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1555</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3739C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x655" flags="0x0">
    <title>Fuel Tank Pressure - Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new fuel tank pressure sensor reading taken into the filtered tank vacuum used by the EVAP tests (and reported on the scan tool). Stock 0.2. Effect: lower = smoother, slower tank vacuum reading Evidence: ledger:E1556</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37992" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x656" flags="0x0">
    <title>Fuel Tank Pressure - Change Check Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new tank pressure reading taken into the copy the tank pressure change check uses. Stock 0.3. Effect: lower = the change check sees smaller, slower changes Evidence: ledger:E1556</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37996" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x657" flags="0x0">
    <title>Fuel Tank Pressure - Settle Time After Key-On</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time after key-on before the tank pressure sensor zero is taken and the tank pressure filtering starts. Stock 0.1 s. Effect: raise = the zero is taken later after key-on Evidence: ledger:E1556</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37994" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x658" flags="0x0">
    <title>Fuel Tank Pressure Change Check - Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time before the tank pressure change check starts comparing changes with its limits. Stock 4 s. Effect: raise = the change check starts later Evidence: ledger:E1556</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3799E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x659" flags="0x0">
    <title>Fuel Tank Pressure Change Check - Fuel Level When Sensor Invalid</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel level used to pick the tank pressure change limits when the fuel level reading is invalid. Stock 85 %. Effect: changes which change limits apply while the fuel level sensor is invalid Evidence: ledger:E1556</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x379A0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x65A" flags="0x0">
    <title>EVAP Vent - Pulse Cycles at Test Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of vent pulse cycles the EVAP test runs when it takes control of the vent. Stock 2. Fuel tank vent solenoid, EVAP test control. Effect: raise = more vent pulses Evidence: ledger:E1559</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x379EA" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x65B" flags="0x0">
    <title>EVAP Vent - Pulse Cycle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Length of each vent pulse cycle at test start. Stock 0.4 s. Fuel tank vent solenoid, EVAP test control. Effect: raise = longer pulses Evidence: ledger:E1559</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x379EB" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x65C" flags="0x0">
    <title>EVAP Vent - Pulse Off Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Part of each vent pulse cycle with the vent command off; the rest of the cycle it is on. Stock 0.2 s. Fuel tank vent solenoid, EVAP test control. Effect: raise = longer off part of each pulse Evidence: ledger:E1559</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x379EC" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>1.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x65D" flags="0x0">
    <title>EVAP Vent On-Time - Vacuum Band Upper Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tank vacuum above this uses the third row of the vent on-time table. Stock 14 inH2O. Fuel tank vent solenoid, EVAP test control. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1559</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x379F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x65E" flags="0x0">
    <title>EVAP Vent On-Time - Fuel Level When Sensor Invalid</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel level used for the vent on-time table when the fuel level reading is invalid. Stock 40 %. Fuel tank vent solenoid, EVAP test control. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1559</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x379F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x65F" flags="0x0">
    <title>EVAP Vent On-Time - Start Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Delay before the vent on-time starts in the small leak pull-down. Stock 0 s. Fuel tank vent solenoid, EVAP test control. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1559</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x379F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x660" flags="0x30">
    <title>EVAP Vent On-Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the vent command stays on, by tank vacuum band (rows) and fuel level (columns). Stock all 0. Fuel tank vent solenoid, EVAP test control. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E1559</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>fuel level (%)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>3</indexcount>
      <units>tank vacuum band</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="up to 12 inH2O" />
      <LABEL index="1" value="12 to 14 inH2O" />
      <LABEL index="2" value="above 14 inH2O" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x379FA" mmedelementsizebits="16" mmedrowcount="3" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>3276.750000</max>
      <MATH equation="X/20"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x661" flags="0x0">
    <title>EVAP Vapour Reference When Fuel Level Invalid</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vapour reference the EVAP test pull-down gain curves use when the fuel level reading is invalid (same scale as the vapour reference at full / empty tank, shown raw). Stock 15349. Effect: selects which pull-down gain points apply with a bad fuel level reading Evidence: ledger:E1560</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3738A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x662" flags="0x0">
    <title>EVAP Service Test - Startup Coolant Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A scan-tool requested EVAP service test is refused when the coolant temperature at start-up was at or above this. Stock 70 C. Effect: raise = the service test is accepted after a warmer start Evidence: ledger:E1560</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3734C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x663" flags="0x0">
    <title>EVAP Service Test - Vehicle Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A scan-tool requested EVAP service test is stopped when vehicle speed rises above this. Stock 16 km/h. Effect: raise = the service test tolerates more vehicle movement Evidence: ledger:E1560</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3734E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x664" flags="0x0">
    <title>EVAP Vent - Scan Tool Command Tank Vacuum Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A scan-tool vent solenoid command is dropped while tank vacuum is above this. Stock 14 inH2O. Effect: raise = the tool can command the vent at higher tank vacuum Evidence: ledger:E1560</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x379EE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x665" flags="0x0">
    <title>A/C Disable After Throttle Closes - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the throttle closes, the A/C compressor is kept from engaging for this time. It applies only while the compressor is not already engaged. Stock 2.0 s. Effect: raise = the compressor waits longer before it can engage after a lift-off Evidence: ledger:E1567</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29A0E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x666" flags="0x0">
    <title>A/C Cut - High Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The A/C compressor is cut when engine speed stays above this for longer than the high speed delay, and it does not engage above it. Stock 6500 rpm. Effect: raise = the compressor keeps running at higher engine speed Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20450" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x667" flags="0x0">
    <title>A/C Cut - Immediate Cut Margin, Park / Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the A/C high engine speed limit: above the sum the compressor is cut at once in Park or Neutral. Stock 500 rpm. Effect: raise = the instant high speed cut in Park / Neutral comes later Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20452" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x668" flags="0x0">
    <title>A/C Cut - High Engine Speed Margin, In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the A/C high engine speed limit when in gear, for the delayed cut and for engagement. Stock 0 rpm. Effect: raise = in gear the compressor runs and engages at higher engine speed Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20454" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x669" flags="0x0">
    <title>A/C Engage - High Engine Speed Hysteresis, In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In gear the compressor may engage only below the high engine speed limit (plus the in-gear margin) minus this. Stock 0 rpm. Effect: raise = engine speed must drop further below the limit before the compressor engages again Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20456" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x66A" flags="0x0">
    <title>A/C Engage - High Engine Speed Hysteresis, Park / Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In Park or Neutral the compressor may engage only below the high engine speed limit minus this. Stock 0 rpm. Effect: raise = engine speed must drop further below the limit before the compressor engages again Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20458" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x66B" flags="0x0">
    <title>A/C Cut - Immediate Cut Margin, In Gear</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the A/C high engine speed limit: above the sum the compressor is cut at once when in gear. Stock 500 rpm. Effect: raise = the instant high speed cut in gear comes later Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2045A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x66C" flags="0x0">
    <title>A/C Cut - Low Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The A/C compressor is cut when engine speed stays below this for longer than the low speed delay. Stock 400 rpm. Effect: raise = the compressor is cut at a higher engine speed in a low speed dip Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2045C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x66D" flags="0x0">
    <title>A/C Cut - Low Engine Speed Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long engine speed must stay below the A/C low engine speed limit before the compressor is cut. Stock 5.0 s. Effect: raise = a low engine speed is tolerated longer before the cut Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2045E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x66E" flags="0x0">
    <title>A/C Cut - High Engine Speed Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long engine speed must stay above the A/C high engine speed limit before the compressor is cut. Stock 5.0 s. Effect: raise = a high engine speed is tolerated longer before the cut Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20460" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x66F" flags="0x0">
    <title>A/C Engage - Low Engine Speed Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The compressor may engage only above the A/C low engine speed limit plus this. Stock 50 rpm. Effect: raise = engine speed must rise further above the low limit before the compressor engages Evidence: ledger:E1569</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x20462" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x670" flags="0x0">
    <title>Cam Phase Transient Detector - Cam Phase Ceiling</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam phase (actual retard from park) above which the airmass predictor&#x27;s cam phase transient detector starts tracking the excess. The excess above this value is filtered twice (fast and slow); a large gap between the two flags a cam phase transient, which switches the airmass predictor to its alternate blend row. Stock 7.0 deg. Effect: raise = cam phase must move further before transients are tracked; lower = tracking starts at less cam phase Evidence: ledger:E1277, ledger:E1572, ledger:E1574</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2CA60" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>deg</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x671" flags="0x30">
    <title>Cam Phase Transient Detector - Threshold by Region</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Gap between the fast and slow filtered cam phase excess at or above which a cam phase transient is flagged, by airmass predictor region. While flagged, the airmass predictor uses its alternate blend row. Stock 0.19 to 3.40 deg. Effect: raise = larger cam phase moves needed to flag a transient; 0 = always flagged Evidence: ledger:E1277, ledger:E1572, ledger:E1574</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>18</indexcount>
      <units>predictor region</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="alt. airflow mode" />
      <LABEL index="1" value="idle window" />
      <LABEL index="2" value="below 1000 rpm, below 26 kPa" />
      <LABEL index="3" value="below 1000 rpm, 26-59 kPa" />
      <LABEL index="4" value="below 1000 rpm, 59-88 kPa" />
      <LABEL index="5" value="below 1000 rpm, above 88 kPa" />
      <LABEL index="6" value="1000-2000 rpm, below 24 kPa" />
      <LABEL index="7" value="1000-2000 rpm, 24-59 kPa" />
      <LABEL index="8" value="1000-2000 rpm, 59-88 kPa" />
      <LABEL index="9" value="1000-2000 rpm, above 88 kPa" />
      <LABEL index="10" value="2000-3000 rpm, below 22 kPa" />
      <LABEL index="11" value="2000-3000 rpm, 22-59 kPa" />
      <LABEL index="12" value="2000-3000 rpm, 59-88 kPa" />
      <LABEL index="13" value="2000-3000 rpm, above 88 kPa" />
      <LABEL index="14" value="above 3000 rpm, below 22 kPa" />
      <LABEL index="15" value="above 3000 rpm, 22-59 kPa" />
      <LABEL index="16" value="above 3000 rpm, 59-88 kPa" />
      <LABEL index="17" value="above 3000 rpm, above 88 kPa" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CA86" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x672" flags="0x30">
    <title>Cam / Crank Correlation Test - Segment Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest crank segment (0..4) a cam pulse may fall in and pass (stock 2 on input 2). When the maximum is below the minimum the window wraps through segment 0. Crankshaft / camshaft position correlation test (P0017 for cam input 1, P0016 for cam input 2): on each new cam pulse the crank segment it falls in (0..4, one segment per 72 crank degrees, counted from the crank wheel&#x27;s missing-tooth reference) is checked against a window; too many samples outside the window set the code, enough samples pass it. On the stock calibration only input 2 runs; input 1&#x27;s values are zero and its test is switched off by its mode setting...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0017)" />
      <LABEL index="1" value="input 2 (P0016)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3684A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>segment</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x673" flags="0x30">
    <title>Cam / Crank Correlation Test - Segment Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest crank segment (0..4) a cam pulse may fall in and pass (stock 3 on input 2). Crankshaft / camshaft position correlation test (P0017 for cam input 1, P0016 for cam input 2): on each new cam pulse the crank segment it falls in (0..4, one segment per 72 crank degrees, counted from the crank wheel&#x27;s missing-tooth reference) is checked against a window; too many samples outside the window set the code, enough samples pass it. On the stock calibration only input 2 runs; input 1&#x27;s values are zero and its test is switched off by its mode setting. Effect: a wider window tolerates more cam / crank phase error before th...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0017)" />
      <LABEL index="1" value="input 2 (P0016)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36852" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>segment</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x674" flags="0x30">
    <title>Cam / Crank Correlation Test - Bad Samples to Fail</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam pulses outside the window that set the code before the pass count is reached (stock 8 on input 2). Crankshaft / camshaft position correlation test (P0017 for cam input 1, P0016 for cam input 2): on each new cam pulse the crank segment it falls in (0..4, one segment per 72 crank degrees, counted from the crank wheel&#x27;s missing-tooth reference) is checked against a window; too many samples outside the window set the code, enough samples pass it. On the stock calibration only input 2 runs; input 1&#x27;s values are zero and its test is switched off by its mode setting. Effect: lower = the code sets sooner on a misaligned...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0017)" />
      <LABEL index="1" value="input 2 (P0016)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3685A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x675" flags="0x30">
    <title>Cam / Crank Correlation Test - Samples to Pass</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam pulses sampled before the test passes, if fewer than the fail count were outside the window (stock 10 on input 2). Crankshaft / camshaft position correlation test (P0017 for cam input 1, P0016 for cam input 2): on each new cam pulse the crank segment it falls in (0..4, one segment per 72 crank degrees, counted from the crank wheel&#x27;s missing-tooth reference) is checked against a window; too many samples outside the window set the code, enough samples pass it. On the stock calibration only input 2 runs; input 1&#x27;s values are zero and its test is switched off by its mode setting. Effect: raise = more samples needed...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (P0017)" />
      <LABEL index="1" value="input 2 (P0016)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36862" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x676" flags="0x30">
    <title>Cam Sensor Start-Up Check - Arming Segment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crank segment in which each cam input&#x27;s start-up check is armed once the crank is synced (stock 2 / 2); its window of updates starts there. The crank segment is 0..4, one segment per 72 crank degrees, counted from the crank wheel&#x27;s missing-tooth reference. Only the low byte of each word is compared. Effect: moves where the start-up check window starts; leave stock Evidence: ledger:E1080, ledger:E1579</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (exhaust)" />
      <LABEL index="1" value="input 2 (intake)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x367D0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>segment</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x677" flags="0x30">
    <title>Cam Sensor Performance - Arming Segment</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Crank segment in which each cam input&#x27;s performance test is armed (stock 2 / 2). The crank segment is 0..4, one segment per 72 crank degrees, counted from the crank wheel&#x27;s missing-tooth reference. Only the low byte of each word is compared. Effect: moves where the performance test windows start; leave stock Evidence: ledger:E1080, ledger:E1579</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (exhaust)" />
      <LABEL index="1" value="input 2 (intake)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x367D8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>segment</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x678" flags="0x0">
    <title>Cam Position Tests - Minimum MAP (Mode 1)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Manifold pressure the engine must be above before the cam position tests arm, for a cam input whose mode setting is 1 (stock 20 kPa). The stock calibration uses modes 0 / 2 on both inputs, so this value is not used. Effect: raise = the tests wait for more load (mode 1 only) Evidence: ledger:E1579</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x679" flags="0x30">
    <title>Cam Angle Test - Cylinders Checked</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of cylinder cam angles the cam angle test checks against its angle window on each sample, per cam input (stock 5 / 5, one per cylinder). 0 skips the angle check for that input. Effect: leave stock: it must match the cylinder count Evidence: ledger:E1080, ledger:E1580</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="input 1 (exhaust)" />
      <LABEL index="1" value="input 2 (intake)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36842" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>cylinders</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x67A" flags="0x0">
    <title>Cam Angle Learn - Reset Angle</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cam angle every cylinder&#x27;s measured, reported and learned angle is reset to (stock 53.1 deg). Part of the per-cylinder cam angle learn, which runs above the per-cylinder learn minimum speed. Effect: the starting point of the learn after a reset Evidence: ledger:E1080, ledger:E1581</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22CFC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>3</decimalpl>
    <min>-128.000000</min>
    <max>127.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x67B" flags="0x0">
    <title>Cranking Run Flag - Run Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at or above which the run flag counts toward setting (stock 550 rpm). Run flag of the cranking control: it sets once the engine has stayed at or above the run speed, and clears once it has stayed at or below the stop speed, each for a number of 25 ms updates. Effect: the speed that counts as running Evidence: ledger:E1583</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2D4AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x67C" flags="0x0">
    <title>Cranking Run Flag - Stop Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at or below which the run flag counts toward clearing (stock 250 rpm). Run flag of the cranking control: it sets once the engine has stayed at or above the run speed, and clears once it has stayed at or below the stop speed, each for a number of 25 ms updates. Effect: the speed that counts as stopped Evidence: ledger:E1583</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2D4AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x67D" flags="0x0">
    <title>Cranking Run Flag - Run Updates</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 25 ms updates counted at the run speed before the flag sets; it sets on the next update (stock 4). Run flag of the cranking control: it sets once the engine has stayed at or above the run speed, and clears once it has stayed at or below the stop speed, each for a number of 25 ms updates. Effect: raise = the run flag sets later Evidence: ledger:E1583</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2D4B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x67E" flags="0x0">
    <title>Cranking Run Flag - Stop Updates</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 25 ms updates counted at the stop speed before the flag clears; it clears on the next update (stock 2). Run flag of the cranking control: it sets once the engine has stayed at or above the run speed, and clears once it has stayed at or below the stop speed, each for a number of 25 ms updates. Effect: raise = the run flag clears later Evidence: ledger:E1583</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2D4B2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>updates</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x67F" flags="0x0">
    <title>Kickdown Request - Pedal Sensor 1 On Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal sensor 1 position above which the kickdown request sets. Stock 99.4 %. Kickdown request: the pedal flag the transmission uses to treat a floored pedal as a kickdown. It sets above the on threshold and stays set until pedal sensor 1 drops to the off threshold; both also need the pedal position above rest (the cross-checked pedal reading) at or above its minimum. Effect: lower = kickdown requested with less pedal travel Evidence: ledger:E1643</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x31B48" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x680" flags="0x0">
    <title>Kickdown Request - Pedal Sensor 1 Off At or Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal sensor 1 position at or below which the kickdown request clears. Stock 75.3 %. Kickdown request: the pedal flag the transmission uses to treat a floored pedal as a kickdown. It sets above the on threshold and stays set until pedal sensor 1 drops to the off threshold; both also need the pedal position above rest (the cross-checked pedal reading) at or above its minimum. Effect: raise = kickdown drops out with less pedal lift; keep below the on threshold Evidence: ledger:E1643</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x31B4A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x681" flags="0x0">
    <title>Kickdown Request - Pedal Above Rest Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The kickdown request can only set or stay set while the pedal position above rest is at or above this. Stock 97.0 %. Kickdown request: the pedal flag the transmission uses to treat a floored pedal as a kickdown. It sets above the on threshold and stays set until pedal sensor 1 drops to the off threshold; both also need the pedal position above rest (the cross-checked pedal reading) at or above its minimum. Effect: lower = kickdown possible with less pedal; keep near the on threshold Evidence: ledger:E1643</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x31B4C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x682" flags="0x0">
    <title>Cruise Control - Resume Ignore Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After a resume, further resume / accel presses are ignored until the switch has been released for this long. Stock 1.5 s. Cruise control, resume / accel switch. Effect: lower = a second press acts sooner after a resume Evidence: ledger:E1644</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2193C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x683" flags="0x0">
    <title>Cruise Control - Accelerate From Standby Below Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Resume from standby: if vehicle speed minus set speed is below this, cruise accelerates back to the set speed; otherwise it resumes normally. Stock 0 km/h. Cruise control, resume / accel switch. Effect: usually left at 0 Evidence: ledger:E1644</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2196C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x684" flags="0x0">
    <title>Cruise Control - Tap Up Window, Speed Error Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A tap up raises the set speed only while vehicle speed minus set speed is at or above this. Stock -16 km/h. Cruise control, resume / accel switch. Effect: lower = tap ups count while further below the set speed Evidence: ledger:E1644</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2196E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x685" flags="0x0">
    <title>Cruise Control - Tap Up Window, Speed Error Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A tap up raises the set speed only while vehicle speed minus set speed is below this. Also, when the accel switch is released with the truck this far or more above the set speed, the current speed becomes the new set speed. Stock 16 km/h. Cruise control, resume / accel switch. Effect: raise = tap ups count further above the set speed Evidence: ledger:E1644</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x21970" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x686" flags="0x0">
    <title>Cruise Control - Coast Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While the set / coast switch is held, the speed demand ramps down at this rate (negative). Stock -6.0 km/h/s. Cruise control demand register: the speed change still to be applied, worked off every 100 ms. Rate in km/h per second. Effect: more negative = coasts down faster while the switch is held Evidence: ledger:E1645</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x21966" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h/s</units>
    <decimalpl>2</decimalpl>
    <min>-2560.000000</min>
    <max>2559.921875</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/12.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x687" flags="0x0">
    <title>Cruise Control - Tap Ramp Rate, Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rate at which a tap&#x27;s speed change is applied while the controller is inside its hysteresis band. Stock 1.0 km/h/s. Cruise control demand register: the speed change still to be applied, worked off every 100 ms. Rate in km/h per second. Effect: raise = taps take effect faster near the set speed Evidence: ledger:E1645</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x21968" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h/s</units>
    <decimalpl>2</decimalpl>
    <min>-2560.000000</min>
    <max>2559.921875</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/12.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x688" flags="0x0">
    <title>Cruise Control - Tap Ramp Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Rate at which a tap up or tap down speed change is applied. Stock 2.0 km/h/s. Cruise control demand register: the speed change still to be applied, worked off every 100 ms. Rate in km/h per second. Effect: raise = the truck reaches a tapped speed sooner Evidence: ledger:E1645</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2196A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h/s</units>
    <decimalpl>2</decimalpl>
    <min>-2560.000000</min>
    <max>2559.921875</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/12.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x689" flags="0x0">
    <title>Cruise Control - Overspeed Disengage Error</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise disengages when the truck is this far above the set speed (allowing for any speed change still being applied); a set / coast press at this overspeed, with both switches released long enough before it, also disengages instead of tapping down. Stock 230 km/h, which never happens, so this is off on stock. Cruise control. Effect: lower (for example 8 km/h) = cruise drops out when the truck runs well over the set speed, such as downhill Evidence: ledger:E1647</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2194E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x68A" flags="0x0">
    <title>Cruise Control - Overspeed Coast Press, Switches Released Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A set / coast press only disengages at overspeed if both cruise switches had been released for at least this long before it. Stock 3.0 s. Cruise control. Effect: only matters when the overspeed disengage error is lowered Evidence: ledger:E1647</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2193A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x68B" flags="0x0">
    <title>Cruise Control - Switch Hold Time to Reset Set Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When a held cruise switch (resume / accel or set / coast) is released: if it was held at least this long, or the truck is below the set speed, the current speed becomes the new set speed; a shorter press with the truck at or above the set speed keeps the set speed. Stock 1.5 s. Cruise control. Effect: lower = shorter holds already re-set the cruise speed Evidence: ledger:E1648</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x21934" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x68C" flags="0x0">
    <title>Dwell - Run Dwell Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the running dwell follows the dwell target, as the fraction of the gap closed every 12.5 ms update. Stock 0.99, so the dwell follows almost at once. Cranking dwell is not filtered. Effect: lower = dwell changes more slowly (smoother, but lags behind voltage and speed changes) Evidence: ledger:E1649</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2F838" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x68D" flags="0x0">
    <title>Misfire Similar Conditions - Cold Band, Coolant At or Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper edge of the cold coolant band. Stock 80 C (an OBD requirement). Misfire similar conditions: a stored misfire record and the current conditions count as similar only if engine speed and load are close and the coolant is in the same band (both in the cold band, or both in the warm band). Effect: emissions rule value: leave at stock Evidence: ledger:E1650</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3501A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x68E" flags="0x0">
    <title>Misfire Similar Conditions - Warm Band, Coolant At or Above</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower edge of the warm coolant band. Stock 70.25 C (70 C per OBD). Misfire similar conditions: a stored misfire record and the current conditions count as similar only if engine speed and load are close and the coolant is in the same band (both in the cold band, or both in the warm band). Effect: emissions rule value: leave at stock Evidence: ledger:E1650</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3501C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x68F" flags="0x0">
    <title>Vehicle Bus - Cruise Set Speed Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Change in the cruise set speed that triggers a new send of its message. Stock 1.0 km/h. Vehicle bus (serial data to the other modules): the message is sent again once at least the minimum interval has passed since it was last sent and the value has changed by at least the change threshold (or a status in it changed). Effect: lower = the set speed is reported in finer steps Evidence: ledger:E1676</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20256" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x690" flags="0x0">
    <title>Vehicle Bus - Cruise Set Speed Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum time between two sends of the cruise set speed message. Stock 0.3 s. Vehicle bus (serial data to the other modules): the message is sent again once at least the minimum interval has passed since it was last sent and the value has changed by at least the change threshold (or a status in it changed). Effect: lower = sent more often Evidence: ledger:E1676</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20258" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x691" flags="0x0">
    <title>PCM Shutdown - Power Mode Off Time Before Shutdown</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the system power mode must stay off before the PCM is allowed to shut itself down. Effect: longer keeps the PCM awake longer after key off Evidence: ledger:E0435, ledger:E1764</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2CF88" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x692" flags="0x0">
    <title>Throttle - Battery Saver Inactivity Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time with the engine off and no pedal activity after which the throttle control goes to its battery saver state. Effect: longer keeps the throttle powered longer Evidence: ledger:E0592, ledger:E0923, ledger:E1764</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x23FD8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x693" flags="0x0">
    <title>Spark - Medium Resolution Calculation Minimum RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at or above which the spark code switches to its modified medium resolution calculation. Effect: leave at stock Evidence: ledger:E1764</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2CFA2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x694" flags="0x0">
    <title>Throttle Position - Learned Minimum, Highest Allowed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest value the learned closed-throttle position may take. Effect: leave at stock Evidence: ledger:E0420, ledger:E1764</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31508" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x695" flags="0x0">
    <title>Throttle Position - Minimum Learn Extension Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time limit on extending the closed-throttle position learn; past it the learn stops. Effect: leave at stock Evidence: ledger:E1764</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x3150C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x696" flags="0x0">
    <title>Throttle Position - Minimum Learn Ignition Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest system voltage at which the closed-throttle position learn runs. Effect: leave at stock Evidence: ledger:E1764</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31512" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>63.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x697" flags="0x0">
    <title>Throttle Position - Minimum Learn MAP Limit While Cranking</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Manifold pressure limit that stops the closed-throttle position learn when it shows the engine is cranking or running. Effect: leave at stock Evidence: ledger:E1764</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x3151A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x698" flags="0x0">
    <title>Pedal Position - Learned Minimum Initial Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Pedal position value used as the starting point of the learned pedal rest position. Effect: leave at stock Evidence: ledger:E1764</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x3152E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x699" flags="0x0">
    <title>EVAP Small Leak Test - Minimum Fuel Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel level (share of tank capacity) at or above which the small leak EVAP test may run. Effect: diagnostic enable window Evidence: ledger:E0781, ledger:E1764</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x69A" flags="0x0">
    <title>Misfire Diagnostic - Throttle Limit for Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle limit used to delay the misfire diagnostic (commanded throttle with the idle share removed). Effect: diagnostic enable window Evidence: ledger:E0772, ledger:E1764</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A90" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x69B" flags="0x0">
    <title>Power Moding - Relay Delay Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Delay that makes sure the run / crank relay state has settled before the PCM acts on it. Effect: leave at stock Evidence: ledger:E0509, ledger:E1764</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x39A54" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x69C" flags="0x0">
    <title>EVAP Vapor Temp Sensor Circuit High Check Enable (P2027)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the EVAP fuel vapour temperature sensor circuit high check on or off. 1: the PCM runs the check and can set P2027. 0: the check never runs, so P2027 is never set and never reported as passed. Stock 0 (off). Effect: 0 = P2027 check off (stock); 1 = check on Evidence: ledger:E0437, ledger:E1765</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x24614" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x69D" flags="0x0">
    <title>EVAP Vapor Temp Sensor Circuit Low Check Enable (P2026)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the EVAP fuel vapour temperature sensor circuit low check on or off. 1: the PCM runs the check and can set P2026. 0: the check never runs, so P2026 is never set and never reported as passed. Stock 0 (off). Effect: 0 = P2026 check off (stock); 1 = check on Evidence: ledger:E0437, ledger:E1765</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x24616" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x69E" flags="0x0">
    <title>EVAP Engine-Off Leak Test Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the engine-off EVAP leak test on or off. 1: the test may run after key off when its conditions are met (fuel level window and the other enable limits). 0: the engine-off test never runs. Stock 1 (on). Effect: 0 = engine-off EVAP test off; 1 = on (stock) Evidence: ledger:E0769, ledger:E1765</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x225B6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x69F" flags="0x0">
    <title>Crank Signal Filter - Update While Running</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Selects whether the crank signal noise filter time is refreshed from its rpm curve while the engine runs (1) or only set at start (0). Stock 1. Effect: leave at stock Evidence: ledger:E0324, ledger:E1274, ledger:E1765</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x22D58" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = updated while running, 0 = set at start only</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A0" flags="0x0">
    <title>Throttle Position Sensor 1 - Voltage Direction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sets how the throttle position sensor 1 voltage is turned into throttle position. 1: the reading is used as is (voltage rises as the throttle opens). 0: the reading is mirrored (full scale minus the reading, voltage falls as the throttle opens). Stock 0. Must match the throttle body fitted; a wrong setting gives throttle faults. Effect: leave at stock unless the throttle body is changed Evidence: ledger:E0764, ledger:E1768</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31524" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = as read, 0 = mirrored</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A1" flags="0x0">
    <title>Throttle Position Sensor 2 - Voltage Direction</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sets how the throttle position sensor 2 voltage is used. 1: the reading is used as is. 0: the reading is mirrored (full scale minus the reading). Stock 1. Must match the throttle body fitted; a wrong setting gives throttle faults. Effect: leave at stock unless the throttle body is changed Evidence: ledger:E1768</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31510" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = as read, 0 = mirrored</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A2" flags="0x0">
    <title>Purge in Open Loop - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Allows EVAP purge before closed loop. 1: after start the PCM picks the cold or warm run time delay by the start-up coolant split and allows open loop purge once the engine has run that long. 0: open loop purge is never allowed and the delay values have no effect. Stock 0 (off). Effect: 1 allows purge in open loop after the delay Evidence: ledger:E0781, ledger:E1768</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x245F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A3" flags="0x0">
    <title>A/C System Present</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tells the PCM whether A/C is fitted. 1: the A/C refrigerant pressure sensor is read and processed. 0: it is not. Stock 0. Effect: leave at stock unless the A/C is wired to the PCM Evidence: ledger:E1768</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x200AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A4" flags="0x0">
    <title>Transmission Type (1 = Automatic, 0 = Manual)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Tells the PCM which gearbox is fitted. 0: the manual gearbox logic runs (gear worked out from engine speed and vehicle speed with the manual gear detection bands, transfer case low range ratio, shift lamp). 1: that logic is off (automatic). Stock 1. Effect: swap setting: 0 for a manual gearbox Evidence: ledger:E1768</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FB76" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = automatic, 0 = manual</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A5" flags="0x0">
    <title>O2 Sensor Circuit Checks - Number of Upstream Sensors</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of upstream O2 sensors the PCM loops over in its O2 sensor checks. Each counted sensor gets its circuit check (the first one sets P0130). 0: the checks never run. Stock 1. Effect: leave at stock Evidence: ledger:E0437, ledger:E1768</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x398BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>sensors</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A6" flags="0x0">
    <title>Brake Switch B Check Enable (P0703)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the brake switch B handling and its circuit check on or off. 1: the PCM runs the check and can set P0703. 0: the check never runs, so P0703 is never set. Stock 0 (off). Effect: 0 = P0703 check off (stock); 1 = check on Evidence: ledger:E0434, ledger:E1768</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2011E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A7" flags="0x0">
    <title>EVAP Leak Test - Temperature Source Select</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Selects the temperature the EVAP small leak test logic uses. 1: ambient air temperature. 0: the lowest intake air temperature since start. With 1 the engine-running test also does not report P0442 from its small leak result. Stock 1. Effect: leave at stock Evidence: ledger:E0434, ledger:E1768, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37356" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = ambient air, 0 = intake air</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A8" flags="0x0">
    <title>EVAP Service Test Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Allows the EVAP service test that a scan tool can command. 1: the test may start when its conditions are met (engine not running, start-up coolant limit and the other checks). 0: the request is always refused. Stock 1. Effect: 0 = service test refused; 1 = allowed (stock) Evidence: ledger:E1768</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3734A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6A9" flags="0x0">
    <title>Throttle Position - Learned Minimum Default Value</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Closed-throttle position value both throttle position sensors&#x27; learned minimums are set to when the learn is reset. Effect: leave at stock Evidence: ledger:E1769</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31506" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6AA" flags="0x0">
    <title>Throttle Position - Minimum Learn Engine Turning RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed above which the PCM times the engine as turning. Once that time passes its limit, the closed-throttle position learn stops. Stock 50 rpm. Effect: leave at stock Evidence: ledger:E0436, ledger:E1769</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31516" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6AB" flags="0x0">
    <title>Throttle Position - Learned Minimum, Lowest Allowed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest value the learned closed-throttle position may take; a learned value below it is treated as out of range. Effect: leave at stock Evidence: ledger:E0436, ledger:E1769</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x3151C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6AC" flags="0x0">
    <title>Throttle Position Sensor 2 - Full Travel Reading</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor 2 reading taken as full throttle travel. Sensor 2&#x27;s travel share is (reading minus its learned minimum) divided by (this value minus the learned minimum). Stock 88.4 %. Effect: leave at stock Evidence: ledger:E0436, ledger:E1769</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31520" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6AD" flags="0x0">
    <title>Pedal Position - Learned Minimum Increase Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Amount added to the learned pedal rest position on each update while it is allowed to rise, up to the learned minimum initial value. Effect: leave at stock Evidence: ledger:E1769</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x3152C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% per update</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6AE" flags="0x0">
    <title>Exhaust Model - Catalyst Channel Stored at Shutdown</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Selects which catalyst channel of the exhaust temperature model is stored at shutdown. The catalyst channels follow the oxygen sensor channels. Stock 0 (the first catalyst channel). Effect: leave at stock Evidence: ledger:E0776, ledger:E1769</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x352DE" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>index (0 = first catalyst channel)</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6AF" flags="0x0">
    <title>EVAP Engine-Off Test - Minimum System Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. System voltage at or below which the engine-off EVAP leak test does not run or is stopped. Stock 0 V (never blocks). Effect: diagnostic enable window Evidence: ledger:E0769, ledger:E1769</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3614E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>31.999512</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/2048"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6B0" flags="0x0">
    <title>O2 Sensors - Number of Sensors</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of oxygen sensors the O2 sensor checks and the exhaust temperature model work through. Stock 2. Matches the fitted sensors: leave at stock. Effect: leave at stock Evidence: ledger:E0760, ledger:E1769</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x361E4" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>sensors</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6B1" flags="0x0">
    <title>EVAP Small Leak Test - Maximum Fuel Level</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel level (share of tank capacity) at or below which the small leak EVAP test may run. Effect: diagnostic enable window Evidence: ledger:E0781, ledger:E1769</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6B2" flags="0x0">
    <title>EVAP Small Leak Test - Maximum Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle speed below which the small leak EVAP test&#x27;s enable timer runs; at or above it the timer is cleared. Stock 161 km/h. Effect: diagnostic enable window Evidence: ledger:E0781, ledger:E1769</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371C0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6B3" flags="0x0">
    <title>Fuel Trim - Nominal Value (No Correction)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel trim value that means no correction; the long term fuel trims are reset to it. Stock 1.0. Effect: leave at stock Evidence: ledger:E0437, ledger:E1769</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x37D9E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6B4" flags="0x0">
    <title>Misfire - Abnormal Event Ratio Check Disable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the misfire abnormal event ratio is held at 0 and never compared with its limit. 0: the ratio is worked out and checked against the abnormal event ratio limit. Stock 0 (check on). Effect: leave at stock Evidence: ledger:E0780, ledger:E1769</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A3A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check off, 0 = on</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6B5" flags="0x0">
    <title>Vehicle Acceleration - Moving Average Filter Weight</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new trans-side vehicle acceleration moving average value taken into its smoothed copy. Stock 0.98. Effect: lower = smoother, slower acceleration value Evidence: ledger:E1769</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x20060" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>weight</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x6B6" flags="0x30">
    <title>Cam Sensor Input Count (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of cam position sensor inputs the PCM services. Every per-cam-input loop (signal checks, cam sensor selection, cam diagnostics) runs this many times. Stock 2. Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0324, ledger:E1274, ledger:E1770</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>1</indexcount>
      <units>item</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="value" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22C72" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="1" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>cam inputs</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6B7" flags="0x30">
    <title>Cam Sensor Assigned to Each Cam Input (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cam sensor each cam input is treated as, which picks the trouble code that input&#x27;s checks look at: 0 = the P0340 sensor, 1 = the P0365 sensor, 2 = the P0345 sensor, 3 = the P0390 sensor. Stock 1, 0 (input 1 is the P0365 sensor, input 2 the P0340 sensor); the H3 has two cam inputs, so the third and fourth values are never used. Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0776, ledger:E1770</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>cam input</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cam input 1" />
      <LABEL index="1" value="cam input 2" />
      <LABEL index="2" value="cam input 3 (not fitted)" />
      <LABEL index="3" value="cam input 4 (not fitted)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36894" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>cam sensor number</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6B8" flags="0x30">
    <title>Response-Tested O2 Sensor Count (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of upstream O2 sensors that get the response tests (P0133 slow response, P1133 switching). Each listed sensor is checked once per pass. Stock 1. Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0437, ledger:E1770</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>1</indexcount>
      <units>item</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="value" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x361BA" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="1" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>O2 sensors</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6B9" flags="0x30">
    <title>O2 Sensor List - Sensor Numbers (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The O2 sensors the PCM has, as a list the response and heater tests pick from. Each value is a sensor number, which selects that sensor&#x27;s trouble codes. Sensor numbers: 0 = bank 1 sensor 1, 1 = bank 1 sensor 2, 2 = bank 1 sensor 3, 3 = bank 2 sensor 1, 4 = bank 2 sensor 2; 5 has no codes (filler). Stock 0, 1, 5, 5 (bank 1 sensor 1 and bank 1 sensor 2; the last two entries are not used by the stock lists). Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0437, ledger:E1561, ledger:E1770</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>list entry</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="entry 1" />
      <LABEL index="1" value="entry 2" />
      <LABEL index="2" value="entry 3" />
      <LABEL index="3" value="entry 4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x36196" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>O2 sensor number</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6BA" flags="0x30">
    <title>Response-Tested O2 Sensors - List Entries (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. For each upstream O2 sensor that gets the response tests (P0133, P1133), which entry of the O2 sensor list it is (0 = first entry). Stock 0 (the first entry, bank 1 sensor 1); the second value is not used because the count is 1. Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0437, ledger:E1770</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="response-tested sensor 1" />
      <LABEL index="1" value="response-tested sensor 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3619E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>O2 sensor list entry (0 = first)</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6BB" flags="0x30">
    <title>Heated O2 Sensors - List Entries (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. For each heated O2 sensor whose heater is checked (P0135, P0141, P0155, P0161), which entry of the O2 sensor list it is (0 = first entry). Stock 0, 1 (bank 1 sensor 1 and bank 1 sensor 2); the PCM checks two heaters, so the third and fourth values are not used. Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0437, ledger:E1770</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="heated sensor 1" />
      <LABEL index="1" value="heated sensor 2" />
      <LABEL index="2" value="heated sensor 3 (not used)" />
      <LABEL index="3" value="heated sensor 4 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x361A2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>O2 sensor list entry (0 = first)</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6BC" flags="0x30">
    <title>Injector Pulse Width Group by Cylinder (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Which computed pulse width group each cylinder&#x27;s injector takes its pulse width from. Stock 0 for every cylinder (all cylinders use the first group). The array has room for eight cylinders; the H3 has five, so the last three values are never used. Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0436, ledger:E1770</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>cylinder</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="cylinder 1" />
      <LABEL index="1" value="cylinder 2" />
      <LABEL index="2" value="cylinder 3" />
      <LABEL index="3" value="cylinder 4" />
      <LABEL index="4" value="cylinder 5" />
      <LABEL index="5" value="cylinder 6 (not fitted)" />
      <LABEL index="6" value="cylinder 7 (not fitted)" />
      <LABEL index="7" value="cylinder 8 (not fitted)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25296" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>pulse width group (0 = first)</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6BD" flags="0x30">
    <title>Misfire Diagnostic - Cylinder Number by Slot (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The cylinder number the misfire diagnostic gives each of its cylinder slots (the slots follow the firing order). It is used for the cylinder it reports and to find the slot of a given cylinder. Stock 4, 2, 1, 3, 5: the firing order 1, 3, 5, 4, 2 starting at cylinder 4. The last three values are not used on five cylinders. Structural setting: it must match the engine and its wiring. Do not edit. Effect: must match the engine: do not edit Evidence: ledger:E0780, ledger:E1770</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>misfire slot</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="slot 1" />
      <LABEL index="1" value="slot 2" />
      <LABEL index="2" value="slot 3" />
      <LABEL index="3" value="slot 4" />
      <LABEL index="4" value="slot 5" />
      <LABEL index="5" value="slot 6 (not used)" />
      <LABEL index="6" value="slot 7 (not used)" />
      <LABEL index="7" value="slot 8 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38A3C" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>cylinder #</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6BE" flags="0x30">
    <title>Vehicle Bus - Module Lost Communication Check Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. One switch per vehicle bus module the PCM listens for. 1: the PCM runs the check on that module&#x27;s messages and can set or pass its U code (U1041, U1056, U1064, U1065, U1066, U1088, U1096, U1152, U1192 in this order). 0: the check never reports, so that code is never set. Stock on for U1041, U1064 and U1096, off for the rest. Turn a module off only when it is not on the vehicle (for example in an engine swap). Effect: 0 = that module&#x27;s U code is never set; 1 = check on Evidence: ledger:E0435, ledger:E1770</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>bus module (by its code)</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="module U1041" />
      <LABEL index="1" value="module U1056" />
      <LABEL index="2" value="module U1064" />
      <LABEL index="3" value="module U1065" />
      <LABEL index="4" value="module U1066" />
      <LABEL index="5" value="module U1088" />
      <LABEL index="6" value="module U1096" />
      <LABEL index="7" value="module U1152" />
      <LABEL index="8" value="module U1192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x20476" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>1 = check on, 0 = off</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x6BF" flags="0x30">
    <title>Catalyst Monitor - Rich Step First Select</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: selects the order of the fuel steps for the O2 switch points. 1: the test starts with its rich step, and the rich step switch voltages are used. 0: it starts with a lean step, and the lean first switch voltages are used. Stock 1. Effect: leave at stock Evidence: ledger:E0676, ledger:E1770</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="bank 1" />
      <LABEL index="1" value="bank 2 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x346AA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>1 = rich step first, 0 = lean first</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x6C0" flags="0x0">
    <title>Brake Torque Limit - Release Step (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the brake torque limit ends, the engine torque limit it set is raised by this amount on each update of its ramp-out phase. Stock 0.5 Nm. The brake torque limit table is at its maximum (no limit) in every cell on the stock calibration, so this has no effect on the stock calibration (dormant). Effect: raise = the torque limit is released faster Evidence: ledger:E0436, ledger:E1771</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x214C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm per update</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C1" flags="0x0">
    <title>Brake Torque Limit - Engine Vacuum Offset (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Added to the filtered engine vacuum before it is used as the vacuum input of the brake torque limit table. Stock 0.2 kPa. The brake torque limit table is at its maximum (no limit) in every cell on the stock calibration, so this has no effect on the stock calibration (dormant). Effect: leave at stock Evidence: ledger:E0436, ledger:E1771</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x214C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C2" flags="0x0">
    <title>Brake Torque Limit - Engine Vacuum Filter, Falling (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lag filter on the engine vacuum used by the brake torque limit, while vacuum is falling or steady: each update moves the filtered value this fraction of the way to the new reading. Stock 0.10. The brake torque limit table is at its maximum (no limit) in every cell on the stock calibration, so this has no effect on the stock calibration (dormant). Effect: lower = the filtered vacuum follows a falling vacuum more slowly Evidence: ledger:E0436, ledger:E1771</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x214C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C3" flags="0x0">
    <title>Brake Torque Limit - Engine Vacuum Filter, Rising (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lag filter on the engine vacuum used by the brake torque limit, while vacuum is rising: each update moves the filtered value this fraction of the way to the new reading. Stock 0.10. The brake torque limit table is at its maximum (no limit) in every cell on the stock calibration, so this has no effect on the stock calibration (dormant). Effect: lower = the filtered vacuum follows a rising vacuum more slowly Evidence: ledger:E0436, ledger:E1771</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x214C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C4" flags="0x0">
    <title>Brake Torque Limit - Driveline Ratio Share</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of the overall driveline torque ratio used to turn the brake torque limit into an engine torque limit (engine limit = brake torque limit / (driveline ratio x this share)). Stock 50 %. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = lower engine torque limit for the same brake torque limit Evidence: ledger:E0436, ledger:E1771</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x214CA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C5" flags="0x0">
    <title>Cruise Control - Vehicle Acceleration Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cruise control: how fast the vehicle acceleration the cruise controller works from follows the measured change in vehicle speed, as the fraction of the gap closed per update. Stock 0.20. Effect: lower = the cruise acceleration signal is smoothed more (slower to react) Evidence: ledger:E0436, ledger:E1771</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x2192E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C6" flags="0x0">
    <title>Cruise Control - Second-Order Acceleration Filter, Last Output Weight (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of the previous filtered acceleration in the second-order cruise acceleration filter. Stock 0. Used only by the alternative second-order acceleration filter, which runs only when its selector is set; the selector is 0 on the stock calibration (the first-order filter runs instead), so this has no effect on the stock calibration (dormant). Effect: dormant on stock: leave at stock Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x21F86" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>-0.125000</min>
    <max>0.124996</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/262144"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C7" flags="0x0">
    <title>Cruise Control - Second-Order Acceleration Filter, Output Two Updates Back Weight (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of the filtered acceleration from two updates back in the second-order cruise acceleration filter. Stock 0. Used only by the alternative second-order acceleration filter, which runs only when its selector is set; the selector is 0 on the stock calibration (the first-order filter runs instead), so this has no effect on the stock calibration (dormant). Effect: dormant on stock: leave at stock Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x21F88" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>-0.125000</min>
    <max>0.124996</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/262144"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C8" flags="0x0">
    <title>Cruise Control - Second-Order Acceleration Filter, New Input Weight (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of the new raw acceleration (vehicle speed change) in the second-order cruise acceleration filter. Stock 0. Used only by the alternative second-order acceleration filter, which runs only when its selector is set; the selector is 0 on the stock calibration (the first-order filter runs instead), so this has no effect on the stock calibration (dormant). Effect: dormant on stock: leave at stock Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x21F8A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>-0.125000</min>
    <max>0.124996</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/262144"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6C9" flags="0x0">
    <title>Cruise Control - Second-Order Acceleration Filter, Last Input Weight (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of the raw acceleration from the previous update in the second-order cruise acceleration filter. Stock 0. Used only by the alternative second-order acceleration filter, which runs only when its selector is set; the selector is 0 on the stock calibration (the first-order filter runs instead), so this has no effect on the stock calibration (dormant). Effect: dormant on stock: leave at stock Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x21F8C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>-0.125000</min>
    <max>0.124996</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/262144"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6CA" flags="0x0">
    <title>Cruise Control - Second-Order Acceleration Filter, Input Two Updates Back Weight (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Weight of the raw acceleration from two updates back in the second-order cruise acceleration filter. Stock 0. Used only by the alternative second-order acceleration filter, which runs only when its selector is set; the selector is 0 on the stock calibration (the first-order filter runs instead), so this has no effect on the stock calibration (dormant). Effect: dormant on stock: leave at stock Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x21F8E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>fraction</units>
    <decimalpl>4</decimalpl>
    <min>-0.125000</min>
    <max>0.124996</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/262144"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6CB" flags="0x0">
    <title>Low Oil Pressure Check - Recovery Margin</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With the oil pressure sensor path on: once oil pressure has been found below the minimum oil pressure for the engine speed, the low oil pressure state clears only when oil pressure is at or above that minimum plus this margin. Stock 25 kPa. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: raise = oil pressure must recover further before the low pressure state clears Evidence: ledger:E1771, ledger:E1831</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36152" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6CC" flags="0x0">
    <title>Airmass Model - Start-Up Blend Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. During the start-up blend the load and fuel airmass move from the speed-density airmass to the capped prediction blend; each update the blend weight rises by this step until it reaches 1.0 (stock 0.10, so about 10 updates). Part of the cylinder airmass model; reference only, DO NOT EDIT. Effect: raise = the start-up blend completes in fewer updates Evidence: ledger:E0780, ledger:E0803, ledger:E1771</description>
    <CATEGORYMEM index="0" category="3" />
    <EMBEDDEDDATA mmedaddress="0x2C730" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6CD" flags="0x0">
    <title>Spark - Medium Resolution Period Ratio Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inside the medium resolution engine speed window the spark timing code predicts the next crank period as the current period times the ratio of the current to the previous period; this is the lowest ratio allowed. Stock 1.0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: leave at stock Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2CF9E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6CE" flags="0x0">
    <title>Spark - Medium Resolution Period Ratio Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Inside the medium resolution engine speed window the spark timing code predicts the next crank period as the current period times the ratio of the current to the previous period; this is the highest ratio allowed. Stock 1.0. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: leave at stock Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2CFA0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>ratio</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6CF" flags="0x0">
    <title>Engine Speed Rate of Change - Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lag filter on the engine speed rate of change (the change in engine speed since the last update divided by the cylinder period): each update moves the filtered value this fraction of the way to the new value. Stock 0.50. Effect: lower = smoother, slower engine speed rate signal Evidence: ledger:E1771</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x22CC0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D0" flags="0x0">
    <title>Vehicle Speed - Distance Rolling Count Reset Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the PCM keeps the distance rolling count reset bit set in its vehicle speed and distance status data before clearing it, in whole seconds. The count only runs in two of the system power modes and restarts otherwise. Stock 1 s. Effect: leave at stock Evidence: ledger:E0486, ledger:E1772</description>
    <CATEGORYMEM index="0" category="9" />
    <EMBEDDEDDATA mmedaddress="0x20062" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D1" flags="0x0">
    <title>Generator Control - Low Speed Mode Cumulative Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The generator low engine speed mode is active while the engine runs below a speed limit taken from desired idle. Its time in that mode adds up; once the total passes this value the mode is turned off. Stock 100 s. Effect: leave at stock Evidence: ledger:E0608, ledger:E0923, ledger:E1772</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x203EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D2" flags="0x0">
    <title>Theft Deterrent - Fuel Decision Minimum Time Since Power-Up</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The theft deterrent fuel decision step is ready only when the PCM has been powered for at least this long, the engine is running and the engine run time limit below is met. Stock 0.2 s. Effect: leave at stock Evidence: ledger:E1772</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x204F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D3" flags="0x0">
    <title>Theft Deterrent - Fuel Decision Minimum Engine Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The theft deterrent fuel decision step is ready only when the engine has run for at least this long (together with the power-up time limit above). Stock 0 s. Effect: leave at stock Evidence: ledger:E1772</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x204F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D4" flags="0x0">
    <title>Coolant Temp Sensor Failsoft - Maximum Substitute Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With a coolant temperature sensor fault, the PCM uses a substitute coolant temperature that rises a step at a time while the engine runs. This is the highest value the substitute rises to. Stock 40 degC. Effect: higher = the engine is treated as warmer after a long run with a failed sensor Evidence: ledger:E0776, ledger:E1772</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x224DA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D5" flags="0x0">
    <title>Fuel Injector Purge - Start Delay (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Delay, once its conditions are met, before the injector purge sequence starts. The purge is not enabled for any cylinder in the stock calibration (per-cylinder enables all 0), so this has no effect on the stock calibration (dormant). Stock 0 s. Effect: leave at stock Evidence: ledger:E0436, ledger:E1772</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26576" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D6" flags="0x0">
    <title>Throttle Position - Minimum Learn Low Voltage Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long system voltage may stay below the minimum learn voltage before the closed-throttle position learn stops taking samples. Effect: leave at stock Evidence: ledger:E0436, ledger:E1772</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31514" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D7" flags="0x0">
    <title>Throttle Position - Minimum Learn Engine Turning Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time engine speed must stay above the learn&#x27;s cranking speed limit before the closed-throttle position learn treats the engine as cranking or running. Effect: leave at stock Evidence: ledger:E0436, ledger:E1772</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31518" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D8" flags="0x0">
    <title>Throttle Position - Minimum Learn Time Limit With Engine Turning</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time limit on the closed-throttle position learn once the engine is cranking or running; past it the learn stops. Effect: leave at stock Evidence: ledger:E0436, ledger:E1772</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31522" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6D9" flags="0x0">
    <title>EVAP Engine-Off Test - Minimum Fuel Vapor Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest fuel vapour temperature for the engine-off EVAP leak test to start. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: diagnostic enable window Evidence: ledger:E0769, ledger:E1772</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3601C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6DA" flags="0x0">
    <title>EVAP Engine-Off Test - Maximum Fuel Vapor Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel vapour temperature at or above which the engine-off EVAP leak test stops with a temperature abort (also the top of the start window when the temperature check enable is on). Stock about 256 degC (never reached). Effect: diagnostic enable window Evidence: ledger:E0769, ledger:E1772</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3614C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6DB" flags="0x0">
    <title>EVAP Small Leak Test - Enable Conditions Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the small leak (0.020 inch) EVAP test enable conditions (fuel level window and the other limits) must hold before the test is allowed to run. Stock 15 s. Effect: diagnostic enable window Evidence: ledger:E0781, ledger:E1772</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6DC" flags="0x0">
    <title>EVAP Leak Test - Valve Control Wait Time Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the EVAP leak test may wait in its valve control step before the wait is flagged as timed out. Stock 0.5 s. Effect: diagnostic timing Evidence: ledger:E0775, ledger:E1772</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37346" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6DD" flags="0x0">
    <title>EVAP Vapor Temp Sensor Performance Check (P2025) - Minimum Engine-Off Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The fuel vapour temperature sensor performance check (P2025) runs after a start only when the engine had been off for longer than this. Stock 540 s. Effect: diagnostic enable window Evidence: ledger:E0437, ledger:E1772</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37A84" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6DE" flags="0x0">
    <title>Watchdog - Background Task Stall Time Before Reset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the PCM&#x27;s background self-test loop may go without running before the PCM stops servicing its watchdog, which then resets the PCM. Stock 10 s. Effect: leave at stock Evidence: ledger:E0530, ledger:E1772</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x39A7A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6DF" flags="0x0">
    <title>EVAP Running Leak Test - Samples Before Pass, Average 1</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of leak samples the engine-running EVAP test must collect before its first leak average can be judged a pass. A fail can be set at any sample; only the pass waits for this count. Stock 6. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: more samples before a P0442 pass Evidence: ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371EA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6E0" flags="0x0">
    <title>EVAP Running Leak Test - Samples Before Pass, Average 2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of leak samples the engine-running EVAP test must collect before its second leak average (updated on every sample) can be judged a pass. Stock 6. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: more samples before a P0442 pass Evidence: ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x371EC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6E1" flags="0x0">
    <title>EVAP Running Test - Skip Small Leak Phase</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the engine-running EVAP test never enters its small leak pull-down and decision phases, so it never sets P0442 from them. 0: after the gross leak phase the test moves on to the small leak phase, and its result can set P0442 (reporting also needs the leak test temperature source setting at 0). Stock 1 (skipped). Effect: 0 = small leak phase runs; 1 = skipped (stock) Evidence: ledger:E0434, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37352" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = skip, 0 = run</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6E2" flags="0x0">
    <title>EVAP Running Test - Vent On-Time Pull-Down Option</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 0: in both the gross leak and the small leak pull-downs the test drives purge from its vacuum pull-down controller. 1: the test does not take over purge during the gross leak pull-down; in the small leak pull-down purge is held at 0 and the vent is opened for the time from the vent on-time table. Stock 0. Effect: leave at stock Evidence: ledger:E0775, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37354" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = vent on-time, 0 = purge pull-down</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6E3" flags="0x0">
    <title>Fuel Trim Monitor - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the fuel trim monitor runs while the engine is running. 0: the monitor is held reset and never enabled. Stock 1. Effect: 0 = fuel trim monitor off; 1 = on (stock) Evidence: ledger:E0636, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D68" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6E4" flags="0x0">
    <title>Misfire - Total Misfire Count Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. When the total misfire count rises above this value, with the misfire logic&#x27;s other conditions met, the PCM sets its excess misfire flag. Stock 100. Effect: diagnostic threshold Evidence: ledger:E0780, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x396A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x6E5" flags="0x30">
    <title>O2 Sensor Circuit Voltage Faults - Related Sensors Checked</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per O2 sensor: which related sensors&#x27; faults are checked before this sensor&#x27;s low or high voltage circuit fault (P0131 / P0137 low, P0132 / P0138 high) is reported. 1: the first related sensor only. 2: also the second related sensor list. If a checked related sensor is in its own fault condition, the report is held back. Stock 1, 1. Effect: leave at stock Evidence: ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>O2 sensor slot</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="slot 1" />
      <LABEL index="1" value="slot 2" />
      <LABEL index="2" value="slot 3 (not used)" />
      <LABEL index="3" value="slot 4 (not used)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x361BC" mmedelementsizebits="8" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>1 = one list, 2 = two lists</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x6E6" flags="0x0">
    <title>Torque Correction Loop - Output Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest correction, in either direction, that the torque correction loop may output. The loop output is clamped to plus or minus this value. Stock 100 Nm. Effect: leave at stock Evidence: ledger:E1774</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x2056E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6E7" flags="0x0">
    <title>Torque Correction Loop - Peak Hold Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit on the held peak of the torque correction loop output. The torque reduction is measured down from this held peak. Stock 70 Nm. Effect: leave at stock Evidence: ledger:E0677, ledger:E1774</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20572" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6E8" flags="0x0">
    <title>Torque Correction Loop - Maximum Drop From Peak</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest drop from the held peak that is passed on. Beyond a small deadband (5 Nm stock) the drop is taken off the engine torque value the PCM uses in this calculation. Stock 100 Nm. Effect: leave at stock Evidence: ledger:E0677, ledger:E1774</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20574" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>-8192.000000</min>
    <max>8191.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6E9" flags="0x0">
    <title>Driver Pedal Throttle Area - Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: which transmission state uses this map is set by the item Pedal Map Select vs Trans State - Normal in this file; the stock selection on this calibration can differ from the H3 described below, so check that table on your own bin before editing this map. Upper limit on the throttle area requested from the accelerator pedal. Requests above it are held at this value. Stock 100 % (no limit). Effect: lower caps the pedal request Evidence: ledger:E0775, ledger:E1774</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x2315A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6EA" flags="0x0">
    <title>EVAP Engine-Off Test - Fuel Temperature Window Check Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the engine-off EVAP leak test starts only when the fuel vapour temperature is between its minimum and maximum values, and an extra stability check runs while the result is evaluated. 0: the temperature window is ignored. Stock 0. Effect: 0 = window ignored (stock); 1 = window applies Evidence: ledger:E0434, ledger:E1774</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35FF4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6EB" flags="0x0">
    <title>Fuel Injector Purge - Number of Pulse Rounds (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How many times the injector purge pulse is repeated, about 0.5 s apart. 0 and 1 both give a single round. Stock 0. No cylinder is enabled for injector purge in the stock calibration, so this has no effect on the stock calibration (dormant). Effect: leave at stock Evidence: ledger:E0436, ledger:E1774</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x26578" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rounds</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6EC" flags="0x0">
    <title>Torque Correction Loop - Drop Deadband</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The drop from the held peak of the torque correction loop is taken off the engine torque value only once twice the drop is larger than this value. Stock 5 Nm. Effect: leave at stock Evidence: ledger:E0612, ledger:E1796</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20FE2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6ED" flags="0x0">
    <title>System Voltage OK Delay - Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the PCM runs its system voltage OK delay check. 0: the check is skipped and its flag and counter are held clear. Stock 1. Effect: leave at stock Evidence: ledger:E0772, ledger:E1796</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x38674" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6EE" flags="0x0">
    <title>Service Throttle Test - Maximum Vehicle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this vehicle speed the scan tool throttle test is refused. Stock 4 km/h. Used only while the scan tool throttle test runs. Effect: safety interlock Evidence: ledger:E0775, ledger:E1796</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x2417A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x6EF" flags="0x30">
    <title>Coolant Warm-Up Monitor - Trouble Code by Step (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The trouble code each step of the coolant warm-up monitor reports, as an entry of the PCM&#x27;s code table. Stock P0125, P0128, P0128. Do not edit: another entry reports a different, unrelated code. Effect: do not edit Evidence: ledger:E0776, ledger:E1563, ledger:E1796</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>3</indexcount>
      <units>warm-up step</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="step 1" />
      <LABEL index="1" value="step 2" />
      <LABEL index="2" value="step 3" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35208" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="3" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>trouble code number</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x6F0" flags="0x0">
    <title>Misfire - Cylinder Index Offset</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The per-cylinder misfire counter that is credited is moved back by this many positions, wrapping at the cylinder count. Stock 0 (no shift). Effect: leave at stock Evidence: ledger:E0780, ledger:E1796</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A4E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cylinder positions</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6F1" flags="0x0">
    <title>ETC Monitor - Expected Throttle Floor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Under the throttle monitor&#x27;s stated conditions the expected throttle value is raised to at least this value. Stock 27.5 %. Effect: leave at stock Evidence: ledger:E0775, ledger:E1796</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x241B0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.35"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6F2" flags="0x0">
    <title>Purge O2 Feedback - Forced Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Value the purge O2 feedback factor is set to in its reset state. Stock 1.00 (no correction). Effect: leave at stock Evidence: ledger:E0775, ledger:E1796</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x243B8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>multiplier</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>1.999969</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/32768"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6F3" flags="0x0">
    <title>Knock Learn Rate - Under-Sampled Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A cylinder whose knock learn sample count is below this value uses the blended learning rate. Same scale as the axis of the Knock Learn Rate - Sample Count Curve. Stock 2560. Effect: leave at stock Evidence: ledger:E0772, ledger:E1796</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2BA44" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples (raw)</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6F4" flags="0x0">
    <title>Fuel Trim Monitor - Confirm Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. In its confirm state, with the fuel trim neither lean nor rich, the fuel trim monitor waits this long before it sets its result. Stock 3.0 s. Effect: diagnostic timing Evidence: ledger:E0462, ledger:E1796</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37D6E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>6553.500000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/10"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6F5" flags="0x0">
    <title>Throttle Position Sensor 1 - Voltage High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A throttle position sensor 1 reading above this voltage is treated as a circuit fault and sets the sensor 1 high input code (P0123). Stock 4.72 V. Effect: diagnostic limit Evidence: ledger:E0434, ledger:E1819</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x22EBE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>5.019531</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13056"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6F6" flags="0x0">
    <title>Throttle Position Sensor 1 - Voltage Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A throttle position sensor 1 reading below this voltage is treated as a circuit fault and sets the sensor 1 low input code (P0122). Stock 0.28 V. Effect: diagnostic limit Evidence: ledger:E0434, ledger:E1819</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x22EC0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>5.019531</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13056"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6F7" flags="0x0">
    <title>Throttle Position Sensor 2 - Voltage High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A throttle position sensor 2 reading above this voltage is treated as a circuit fault and sets the sensor 2 high input code (P0223). Stock 4.72 V. Effect: diagnostic limit Evidence: ledger:E0434, ledger:E1819</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x22EC2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>5.019531</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13056"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6F8" flags="0x0">
    <title>Throttle Position Sensor 2 - Voltage Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A throttle position sensor 2 reading below this voltage is treated as a circuit fault and sets the sensor 2 low input code (P0222). Stock 0.28 V. Effect: diagnostic limit Evidence: ledger:E0434, ledger:E1819</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x22EC4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>5.019531</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13056"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6F9" flags="0x0">
    <title>P2610 Engine-Off Timer Check - Expected Step</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of engine-off timer counts expected between two samples of the engine-off timer check. A sample with a different step counts as bad, and enough bad samples set P2610. Stock 1. Effect: leave at stock Evidence: ledger:E0434, ledger:E1819</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A48" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>timer counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6FA" flags="0x0">
    <title>Oil Pressure Monitor - Engine Running Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed the engine must stay above (for the running time) before the low oil pressure monitor treats it as running and can set its warning. Stock 550 rpm. Effect: leave at stock Evidence: ledger:E0776, ledger:E1819</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x3617A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6FB" flags="0x0">
    <title>Oil Pressure Monitor - Engine Running Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the engine speed must stay above the running speed before the low oil pressure monitor treats the engine as running. Stock 2.5 s. Effect: leave at stock Evidence: ledger:E0776, ledger:E1819</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x3617C" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6FC" flags="0x0">
    <title>Traction Control Input - Hold Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the last received traction control input values are kept without a new message before they are cleared. Stock 0 (cleared on the first tick after each message). Effect: leave at stock Evidence: ledger:E0434, ledger:E1819</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x302C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6FD" flags="0x0">
    <title>P0128 Check - Minimum Intake Air Temperature</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The thermostat check P0128 only runs on a trip when the lowest intake air temperature since start is above this. Stock -6.75 degC. Effect: diagnostic enable window Evidence: ledger:E0587, ledger:E0920, ledger:E1819</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3518E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6FE" flags="0x0">
    <title>Low Oil Pressure Check - Set Delay</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long low oil pressure must be seen, with the engine running, before the PCM sets its low oil pressure state: the low oil pressure input active (stock, oil pressure estimate path), or with the sensor path on, oil pressure below the minimum oil pressure for the engine speed. Stock 1.0 s. Effect: longer delays the warning Evidence: ledger:E0776, ledger:E1829, ledger:E1831</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36178" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x6FF" flags="0x0">
    <title>Oil Pressure Sensor Path Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the PCM reads engine oil pressure from the oil pressure sensor (Engine Oil Pressure vs Sensor Voltage) and runs the low oil pressure check against the minimum oil pressure for the engine speed. 0: the sensor is not used. Stock 0 (the H3 calibration uses the oil pressure estimate). Effect: 1 only with an oil pressure sensor fitted Evidence: ledger:E0436, ledger:E1831</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x225BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x700" flags="0x0">
    <title>Oil Pressure Estimate Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. 1: the PCM estimates engine oil pressure from coolant temperature and engine speed (Engine Oil Pressure Estimate tables), sends it on the vehicle bus, and sets its low oil pressure state from the low oil pressure input. 0: no estimate. Stock 1. Effect: leave at stock Evidence: ledger:E0436, ledger:E1831</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x225BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x701" flags="0x0">
    <title>Throttle Position - Minimum Learn Change Band</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How far the throttle position reading may move from its lowest value so far before the closed-throttle position learn restarts its settle time and follows the new reading. Also the least change from the stored learned value needed to replace it. Stock 0.50 %. Effect: leave at stock Evidence: ledger:E0436, ledger:E1838</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x3150A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x702" flags="0x0">
    <title>Throttle Position - Minimum Learn Settle Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long the throttle position reading must stay within the learn change band before the closed-throttle position learn stores it as the learned minimum. Stock 0.06 s. Effect: leave at stock Evidence: ledger:E0436, ledger:E1838</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x3150E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x703" flags="0x0">
    <title>Throttle Position Sensor 1 - Backup Full Scale Voltage</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On the backup throttle position path, the throttle position sensor 1 voltage that reads as 100 % (the learned closed-throttle voltage reads as 0 %). Stock 4.42 V. Effect: leave at stock Evidence: ledger:E0764, ledger:E1839</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x31526" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>5.019531</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/13056"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x704" flags="0x0">
    <title>Pedal Position Sensors - Learned Minimum Mismatch Limit (P2138)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Largest allowed difference between the learned closed-pedal values of the two pedal position sensors; a larger difference counts as a failed P2138 sample. Stock 5.0 %. Effect: diagnostic limit Evidence: ledger:E0434, ledger:E1251, ledger:E1839</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22DF2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>100.390625</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/652.8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x705" flags="0x0">
    <title>Idle Speed Control - Spark Term Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lower limit on the idle spark term the idle speed controller works with; a lower idle spark term is raised to this value. The idle spark term is the idle base spark plus the idle underspeed spark correction; the idle speed controller uses the limited term when it sets the idle airflow request. Stock -16.0 deg. Effect: leave at stock Evidence: ledger:E0632, ledger:E1852</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x21FD0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x706" flags="0x0">
    <title>Idle Speed Control - Spark Term Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upper limit on the idle spark term the idle speed controller works with; a higher idle spark term is lowered to this value. The idle spark term is the idle base spark plus the idle underspeed spark correction; the idle speed controller uses the limited term when it sets the idle airflow request. Stock 25.0 deg. Effect: leave at stock Evidence: ledger:E0632, ledger:E1852</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x21FD2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x707" flags="0x0">
    <title>Reduced Engine Power - Speed Filter Rate</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the filtered vehicle speed used by the reduced engine power throttle limit follows the measured speed, as the fraction of the gap closed per update. Part of the reduced engine power throttle limit, which is active only while a throttle control fault is set; it limits the throttle when the vehicle accelerates harder than allowed (a sign of wheel spin or a false speed reading). Stock 0.22. Effect: leave at stock Evidence: ledger:E1867</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x23042" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x708" flags="0x0">
    <title>Reduced Engine Power - Throttle Area Limit at Low Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. While a throttle control fault is active, at 8 km/h or slower the throttle opening is limited to this share of full throttle area. Stock 6.3 %. Effect: raise = more throttle allowed at low speed under reduced engine power Evidence: ledger:E1867</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x23044" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>99.998474</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/655.36"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x709" flags="0x0">
    <title>Reduced Engine Power - High Speed Band Start</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this vehicle speed the high speed acceleration threshold applies. Part of the reduced engine power throttle limit, which is active only while a throttle control fault is set; it limits the throttle when the vehicle accelerates harder than allowed (a sign of wheel spin or a false speed reading). Stock 36.0 km/h. Effect: leave at stock Evidence: ledger:E1867</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x23046" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x70A" flags="0x0">
    <title>Reduced Engine Power - Low Speed Band End</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this vehicle speed the low speed acceleration threshold applies; between this and the high speed band start the middle threshold applies. Part of the reduced engine power throttle limit, which is active only while a throttle control fault is set; it limits the throttle when the vehicle accelerates harder than allowed (a sign of wheel spin or a false speed reading). Stock 16.0 km/h. Effect: leave at stock Evidence: ledger:E1867</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x23048" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x70B" flags="0x0">
    <title>Reduced Engine Power - Acceleration Threshold, High Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle acceleration above which the reduced engine power throttle limit starts, used above the high speed band start. Part of the reduced engine power throttle limit, which is active only while a throttle control fault is set; it limits the throttle when the vehicle accelerates harder than allowed (a sign of wheel spin or a false speed reading). Stock 38.4 km/h/s. Effect: raise = harder acceleration allowed before the limit starts Evidence: ledger:E1867</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x2304A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x70C" flags="0x0">
    <title>Reduced Engine Power - Acceleration Threshold, Middle Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle acceleration above which the reduced engine power throttle limit starts, used between the two speed bands. Part of the reduced engine power throttle limit, which is active only while a throttle control fault is set; it limits the throttle when the vehicle accelerates harder than allowed (a sign of wheel spin or a false speed reading). Stock 38.4 km/h/s. Effect: raise = harder acceleration allowed before the limit starts Evidence: ledger:E1867</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x2304C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x70D" flags="0x0">
    <title>Reduced Engine Power - Acceleration Threshold, Low Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Vehicle acceleration above which the reduced engine power throttle limit starts, used below the low speed band end. Part of the reduced engine power throttle limit, which is active only while a throttle control fault is set; it limits the throttle when the vehicle accelerates harder than allowed (a sign of wheel spin or a false speed reading). Stock 38.4 km/h/s. Effect: raise = harder acceleration allowed before the limit starts Evidence: ledger:E1867</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x2304E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h/s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x70E" flags="0x0">
    <title>Segment 2 (System) - GM Part Number</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. GM service part number of this calibration segment. The same number is stored as text a few bytes later. It identifies which calibration version is in the PCM; it does not change how the engine runs. Read only. Effect: identification only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x20004" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>part number</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>4294967295.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x70F" flags="0x0">
    <title>Segment 2 (System) - Checksum (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Checksum word of this segment: every 16-bit word of the segment, this one included, adds up to zero. Your flash or checksum tool must recompute it after any edit in this segment. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x20000" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x710" flags="0x0">
    <title>Segment 2 (System) - ROM Check CRC (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Check value the PCM&#x27;s ROM test (P0601) compares against while the engine runs: a CRC-16 of the segment, stored with its bytes swapped. If it is not updated after an edit in this segment, the PCM can set P0601. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x2001C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x711" flags="0x0">
    <title>Segment 3 (Fuel / System) - GM Part Number</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. GM service part number of this calibration segment. The same number is stored as text a few bytes later. It identifies which calibration version is in the PCM; it does not change how the engine runs. Read only. Effect: identification only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x2008C" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>part number</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>4294967295.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x712" flags="0x0">
    <title>Segment 3 (Fuel / System) - Checksum (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Checksum word of this segment: every 16-bit word of the segment, this one included, adds up to zero. Your flash or checksum tool must recompute it after any edit in this segment. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x20088" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x713" flags="0x0">
    <title>Segment 3 (Fuel / System) - ROM Check CRC (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Check value the PCM&#x27;s ROM test (P0601) compares against while the engine runs: a CRC-16 of the segment, stored with its bytes swapped. If it is not updated after an edit in this segment, the PCM can set P0601. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x200A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x714" flags="0x0">
    <title>Segment 4 (Engine Calibration) - GM Part Number</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. GM service part number of this calibration segment. The same number is stored as text a few bytes later. It identifies which calibration version is in the PCM; it does not change how the engine runs. Read only. Effect: identification only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x2052E" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>part number</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>4294967295.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x715" flags="0x0">
    <title>Segment 4 (Engine Calibration) - Checksum (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Checksum word of this segment: every 16-bit word of the segment, this one included, adds up to zero. Your flash or checksum tool must recompute it after any edit in this segment. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x2052A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x716" flags="0x0">
    <title>Segment 4 (Engine Calibration) - ROM Check CRC (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Check value the PCM&#x27;s ROM test (P0601) compares against while the engine runs: a CRC-16 of the segment, stored with its bytes swapped. If it is not updated after an edit in this segment, the PCM can set P0601. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x20546" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x717" flags="0x0">
    <title>Segment 5 (Engine Diagnostics) - GM Part Number</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. GM service part number of this calibration segment. The same number is stored as text a few bytes later. It identifies which calibration version is in the PCM; it does not change how the engine runs. Read only. Effect: identification only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x34550" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>part number</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>4294967295.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x718" flags="0x0">
    <title>Segment 5 (Engine Diagnostics) - Checksum (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Checksum word of this segment: every 16-bit word of the segment, this one included, adds up to zero. Your flash or checksum tool must recompute it after any edit in this segment. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x3454C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x719" flags="0x0">
    <title>Segment 5 (Engine Diagnostics) - ROM Check CRC (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Check value the PCM&#x27;s ROM test (P0601) compares against while the engine runs: a CRC-16 of the segment, stored with its bytes swapped. If it is not updated after an edit in this segment, the PCM can set P0601. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x34568" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x71A" flags="0x0">
    <title>Segment 6 (Transmission Calibration) - GM Part Number</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. GM service part number of this calibration segment. The same number is stored as text a few bytes later. It identifies which calibration version is in the PCM; it does not change how the engine runs. Read only. Effect: identification only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x3F88C" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>part number</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>4294967295.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x71B" flags="0x0">
    <title>Segment 6 (Transmission Calibration) - Checksum (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Checksum word of this segment: every 16-bit word of the segment, this one included, adds up to zero. Your flash or checksum tool must recompute it after any edit in this segment. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x3F888" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x71C" flags="0x0">
    <title>Segment 6 (Transmission Calibration) - ROM Check CRC (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Check value the PCM&#x27;s ROM test (P0601) compares against while the engine runs: a CRC-16 of the segment, stored with its bytes swapped. If it is not updated after an edit in this segment, the PCM can set P0601. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x3F8A4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x71D" flags="0x0">
    <title>Segment 7 (Transmission Diagnostics) - GM Part Number</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. GM service part number of this calibration segment. The same number is stored as text a few bytes later. It identifies which calibration version is in the PCM; it does not change how the engine runs. Read only. Effect: identification only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x3FCAE" mmedelementsizebits="32" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>part number</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>4294967295.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x71E" flags="0x0">
    <title>Segment 7 (Transmission Diagnostics) - Checksum (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Checksum word of this segment: every 16-bit word of the segment, this one included, adds up to zero. Your flash or checksum tool must recompute it after any edit in this segment. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x3FCAA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x71F" flags="0x0">
    <title>Segment 7 (Transmission Diagnostics) - ROM Check CRC (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Check value the PCM&#x27;s ROM test (P0601) compares against while the engine runs: a CRC-16 of the segment, stored with its bytes swapped. If it is not updated after an edit in this segment, the PCM can set P0601. Reference only: DO NOT EDIT. Effect: reference only Evidence: ledger:E1290, ledger:catalog</description>
    <CATEGORYMEM index="0" category="13" />
    <EMBEDDEDDATA mmedaddress="0x3FCC6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>raw</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x720" flags="0x30">
    <title>P0507 Idle Speed High - Speed Error Threshold vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed above desired by at least this much (by coolant temperature) runs the P0507 fail timer; once it reaches the high-error fail time one P0507 fail period is counted. Stock 150 rpm at all temperatures. Part of the idle speed diagnostic (P0506 idle speed lower than expected, P0507 higher than expected), which runs only once its enable conditions are met. Effect: raise = more overspeed needed before P0507 counts Evidence: ledger:E0639, ledger:E1239, ledger:E1603</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37FE0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>-4096.000000</min>
      <max>4095.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x721" flags="0x30">
    <title>P0506 Idle Speed Low - Speed Error Threshold vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle speed below desired by at least this much (negative values, by coolant temperature) runs the P0506 fail timer; once it reaches the low-error fail time one P0506 fail period is counted. Stock -75 rpm at all temperatures. Part of the idle speed diagnostic (P0506 idle speed lower than expected, P0507 higher than expected), which runs only once its enable conditions are met. Effect: lower (more negative) = more underspeed needed before P0506 counts Evidence: ledger:E0639, ledger:E1239, ledger:E1603</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38004" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>-4096.000000</min>
      <max>4095.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x722" flags="0x0">
    <title>Vehicle Bus - Intake Air Temperature Change Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Change in the intake air temperature that triggers a new send of its message. Stock 5 C. Vehicle bus (serial data to the other modules): the message is sent again once at least the minimum interval has passed since it was last sent and the value has changed by at least the change threshold (or a status in it changed). Effect: lower = the temperature is reported in finer steps Evidence: ledger:E0627, ledger:E0801, ledger:E0805, ledger:E1603, ledger:E1676</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20242" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x723" flags="0x0">
    <title>Vehicle Bus - Intake Air Temperature Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Minimum time between two sends of the intake air temperature message. Stock 1.0 s. Vehicle bus (serial data to the other modules): the message is sent again once at least the minimum interval has passed since it was last sent and the value has changed by at least the change threshold (or a status in it changed). Effect: lower = sent more often Evidence: ledger:E0627, ledger:E0801, ledger:E0805, ledger:E1603, ledger:E1676</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x20244" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x724" flags="0x30">
    <title>Calculated Load - IAT Density Factor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Intake air temperature factor on the 100 % calculated load airflow. Only changes the calculated load value reported to a scan tool (PID 04). Stock 1.13 at -40 C falling to 0.85 at 140 C. Effect: raise = lower reported calculated load at that intake temperature Evidence: ledger:E0740, ledger:E1340, ledger:E1603</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-34.375" />
      <LABEL index="2" value="-28.75" />
      <LABEL index="3" value="-23.125" />
      <LABEL index="4" value="-17.5" />
      <LABEL index="5" value="-11.875" />
      <LABEL index="6" value="-6.25" />
      <LABEL index="7" value="-0.625" />
      <LABEL index="8" value="5" />
      <LABEL index="9" value="10.625" />
      <LABEL index="10" value="16.25" />
      <LABEL index="11" value="21.875" />
      <LABEL index="12" value="27.5" />
      <LABEL index="13" value="33.125" />
      <LABEL index="14" value="38.75" />
      <LABEL index="15" value="44.375" />
      <LABEL index="16" value="50" />
      <LABEL index="17" value="55.625" />
      <LABEL index="18" value="61.25" />
      <LABEL index="19" value="66.875" />
      <LABEL index="20" value="72.5" />
      <LABEL index="21" value="78.125" />
      <LABEL index="22" value="83.75" />
      <LABEL index="23" value="89.375" />
      <LABEL index="24" value="95" />
      <LABEL index="25" value="100.625" />
      <LABEL index="26" value="106.25" />
      <LABEL index="27" value="111.875" />
      <LABEL index="28" value="117.5" />
      <LABEL index="29" value="123.125" />
      <LABEL index="30" value="128.75" />
      <LABEL index="31" value="134.375" />
      <LABEL index="32" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C788" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x725" flags="0x30">
    <title>Calculated Load - Reference Airflow vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Airflow that counts as 100 % calculated load at each rpm (corrected by baro and the IAT factor). Only changes the calculated load value reported to a scan tool (PID 04), not fuelling. Stock 0 rising to 180 g/s at 6000 rpm. Effect: raise = lower reported calculated load at that rpm Evidence: ledger:E0740, ledger:E1340, ledger:E1603</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C740" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x726" flags="0x0">
    <title>Catalyst Monitor - Maximum Storage Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: storage time recorded when the downstream O2 sensor does not switch within its time limits. Stock 7.0 s. Effect: raise = a catalyst that outlasts the test is scored with a longer storage time Evidence: ledger:E1000, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345E6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x727" flags="0x0">
    <title>Catalyst Monitor Enable - Off Idle Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: an idle period only qualifies for a test if the engine spent at least this long off idle just before it. Stock 35 s. Effect: lower = a shorter drive between idle periods is enough Evidence: ledger:E0998, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345BC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x728" flags="0x0">
    <title>Catalyst Monitor Enable - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420) idle test: an idle period only qualifies once the engine has been running at least this long. Stock 600 s. Effect: lower = the test can run sooner after a start Evidence: ledger:E0814, ledger:E0998, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345BE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x729" flags="0x0">
    <title>Catalyst Monitor - Tests per Engine Run</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Catalyst monitor (P0420): most catalyst tests that may be started in one engine run. Stock 12. Effect: lower = fewer catalyst tests are started per engine run Evidence: ledger:E1082, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x345B4" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>tests</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x72A" flags="0x0">
    <title>Closed Loop Coolant Window Mode - Engine Run Time Below</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. Closed loop fuel, coolant window mode: the short term trim uses a separate set of gains while coolant is inside a window and the engine has run for less than a set time. Dormant on the stock calibration: the run time is 0, so the mode is never selected. This is the run time: the mode is only used while the engine has run for less than this. Stock 0 s, which switches the mode off. Ef...</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x24E38" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x72B" flags="0x30">
    <title>Cold Start Emission Monitor - Speed Term vs RPM (dormant, DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Speed term curve of the cold start emission monitor (fault code P1400): converts engine speed (0 to 2400 rpm) into the monitor&#x27;s speed term. The same curve is applied to the expected and to the actual engine speed, and each speed term is multiplied by the matching spark term before the monitor compares expected with actual. On this calibration the monitor is switched off and the curve&#x27;s size word is blank, so it is never used; the points are shown at the size the lookup has when the monitor is in use. Dormant: no effect on this truck&#x27;s software. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="300" />
      <LABEL index="2" value="600" />
      <LABEL index="3" value="900" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1500" />
      <LABEL index="6" value="1800" />
      <LABEL index="7" value="2100" />
      <LABEL index="8" value="2400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34F5C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x72C" flags="0x30">
    <title>MAP Circuit High - Arming Time vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. After each start the MAP sensor circuit high monitor (P0108 and P1106) waits this long before it counts samples, by coolant temperature at start. Five points from -30 to 30 C in 15 C steps; outside that range the end points are used. Stock 40 s at -30 C, 30 s at -15 C, 20 s at 0 and 15 C, 5 s at 30 C and above. Effect: raise = the high-circuit monitor starts later after a start Evidence: ledger:E0566, ledger:E0890, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>5</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-30" />
      <LABEL index="1" value="-15" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="15" />
      <LABEL index="4" value="30" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x389EA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="5" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x72D" flags="0x30">
    <title>Crank Output Mode 2 - Lower Engine Speed vs Battery Voltage (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Engine speed at or below which the crank-timed output channels enter mode 2, by battery voltage (with the upper speed above it ending the mode). Used only when mode 2 is enabled. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = mode 2 starts at a higher engine speed at that voltage) Evidence: ledger:E0644, ledger:E0749, ledger:E1271, ledger:E1603</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>22</indexcount>
      <units>V (battery)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="4.5" />
      <LABEL index="1" value="5.5" />
      <LABEL index="2" value="6.5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="8.5" />
      <LABEL index="5" value="9.5" />
      <LABEL index="6" value="10.5" />
      <LABEL index="7" value="11.5" />
      <LABEL index="8" value="12.5" />
      <LABEL index="9" value="13.5" />
      <LABEL index="10" value="14.5" />
      <LABEL index="11" value="15.5" />
      <LABEL index="12" value="16.5" />
      <LABEL index="13" value="17.5" />
      <LABEL index="14" value="18.5" />
      <LABEL index="15" value="19.5" />
      <LABEL index="16" value="20.5" />
      <LABEL index="17" value="21.5" />
      <LABEL index="18" value="22.5" />
      <LABEL index="19" value="23.5" />
      <LABEL index="20" value="24.5" />
      <LABEL index="21" value="25.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CFEA" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="22" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x72E" flags="0x30">
    <title>Crank Output Mode 2 - Upper Engine Speed vs Battery Voltage (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Upper engine speed of the mode 2 band of the crank-timed output channels, by battery voltage: once in mode 2, the outputs stay in it until engine speed reaches this. Used only when mode 2 is enabled. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = mode 2 is kept up to a higher engine speed at that voltage) Evidence: ledger:E0644, ledger:E0749, ledger:E1271, ledger:E1603</description>
    <CATEGORYMEM index="0" category="7" />
    <XDFAXIS id="x">
      <indexcount>22</indexcount>
      <units>V (battery)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="4.5" />
      <LABEL index="1" value="5.5" />
      <LABEL index="2" value="6.5" />
      <LABEL index="3" value="7.5" />
      <LABEL index="4" value="8.5" />
      <LABEL index="5" value="9.5" />
      <LABEL index="6" value="10.5" />
      <LABEL index="7" value="11.5" />
      <LABEL index="8" value="12.5" />
      <LABEL index="9" value="13.5" />
      <LABEL index="10" value="14.5" />
      <LABEL index="11" value="15.5" />
      <LABEL index="12" value="16.5" />
      <LABEL index="13" value="17.5" />
      <LABEL index="14" value="18.5" />
      <LABEL index="15" value="19.5" />
      <LABEL index="16" value="20.5" />
      <LABEL index="17" value="21.5" />
      <LABEL index="18" value="22.5" />
      <LABEL index="19" value="23.5" />
      <LABEL index="20" value="24.5" />
      <LABEL index="21" value="25.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CFBC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="22" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x72F" flags="0x30">
    <title>Cold Start Emission Monitor - Expected Spark, Idle Mode, Park / Neutral (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Expected spark advance for the cold start emission monitor (fault code P1400) while the spark control is in its idle mode with the transmission in Park or Neutral, by cylinder airmass (rows, 0.08 to 0.72 g/cyl) and engine speed (columns, 400 to 1600 rpm). The value is multiplied by the monitor&#x27;s four factor curves (run time, start-up coolant, coolant and throttle) and compared with the actual spark advance; in every other spark mode the main expected spark table is used instead. The layout is the one the lookup&#x27;s own input scaling fits (seven speed points, seventeen airmass points). On this calibration the...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1000" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1400" />
      <LABEL index="6" value="1600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34BCE" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x730" flags="0x30">
    <title>Cold Start Emission Monitor - Expected Spark, Idle Mode, In Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Expected spark advance for the cold start emission monitor (fault code P1400) while the spark control is in its idle mode with the transmission in gear, by cylinder airmass (rows, 0.08 to 0.72 g/cyl) and engine speed (columns, 400 to 1600 rpm). The value is multiplied by the monitor&#x27;s four factor curves (run time, start-up coolant, coolant and throttle) and compared with the actual spark advance; in every other spark mode the main expected spark table is used instead. The layout is the one the lookup&#x27;s own input scaling fits (seven speed points, seventeen airmass points). On this calibration the monitor is...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1000" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1400" />
      <LABEL index="6" value="1600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34CC6" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x731" flags="0x0">
    <title>Engine Speed Filter Weight - Filtered Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Share of each new engine speed reading taken into the filtered engine speed every 25 ms. The filtered engine speed is the one the transmission logic reads (garage shift, shift and converter clutch checks). Stock 0.75. Effect: lower = smoother but slower filtered engine speed; 1.0 = no filtering Evidence: ledger:E1570, ledger:E1603</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3F8AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x732" flags="0x0">
    <title>EVAP Vent On-Time - Vacuum Band Lower Limit (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Tank vacuum at or below this uses the first row of the vent on-time table. Stock 12 inH2O. Fuel tank vent solenoid, EVAP test control. Used only with the vent on-time option, which is switched off on this truck, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1559, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x379F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x733" flags="0x30">
    <title>First-Run Mode - Open-Loop Fuel Multiplier vs Run Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. First-run mode runs only during the first 12 s of engine running recorded by the PCM (kept through power-off), with a stored flag set, the mode enable set and start-up coolant inside the coolant window. During it the open-loop commanded fuel/air ratio is multiplied by this, by recorded run time (0 to 64 s). Stock 1.99 up to 6 s, 1.65 at 8 s, 1.30 at 10 s, 1.0 from 12 s. Effect: raise = richer open-loop fuel during first-run mode at that recorded run time Evidence: ledger:E0653, ledger:E0937, ledger:E1227, ledger:E1603</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>s</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="4" />
      <LABEL index="3" value="6" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="12" />
      <LABEL index="7" value="14" />
      <LABEL index="8" value="16" />
      <LABEL index="9" value="18" />
      <LABEL index="10" value="20" />
      <LABEL index="11" value="22" />
      <LABEL index="12" value="24" />
      <LABEL index="13" value="26" />
      <LABEL index="14" value="28" />
      <LABEL index="15" value="30" />
      <LABEL index="16" value="32" />
      <LABEL index="17" value="34" />
      <LABEL index="18" value="36" />
      <LABEL index="19" value="38" />
      <LABEL index="20" value="40" />
      <LABEL index="21" value="42" />
      <LABEL index="22" value="44" />
      <LABEL index="23" value="46" />
      <LABEL index="24" value="48" />
      <LABEL index="25" value="50" />
      <LABEL index="26" value="52" />
      <LABEL index="27" value="54" />
      <LABEL index="28" value="56" />
      <LABEL index="29" value="58" />
      <LABEL index="30" value="60" />
      <LABEL index="31" value="62" />
      <LABEL index="32" value="64" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2956E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x734" flags="0x30">
    <title>Fuel Cutoff RPM Reduction vs Run Time vs Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. RPM subtracted from the in-gear rev limit, vs engine run time and coolant (cold-start rev limiting). All 0 on the stock H3 (E0201) Effect: positive values lower the rev limit when cold / just started Evidence: ledger:E0201, ledger:E0213, ledger:E0218, ledger:E0260, ledger:E0782, ledger:E1413, ledger:E1603</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>s (engine run time)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.0" />
      <LABEL index="1" value="5.3" />
      <LABEL index="2" value="10.6" />
      <LABEL index="3" value="15.9" />
      <LABEL index="4" value="21.2" />
      <LABEL index="5" value="26.6" />
      <LABEL index="6" value="31.9" />
      <LABEL index="7" value="37.2" />
      <LABEL index="8" value="42.5" />
      <LABEL index="9" value="47.8" />
      <LABEL index="10" value="53.1" />
      <LABEL index="11" value="58.4" />
      <LABEL index="12" value="63.8" />
      <LABEL index="13" value="69.1" />
      <LABEL index="14" value="74.4" />
      <LABEL index="15" value="79.7" />
      <LABEL index="16" value="85.0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40.0" />
      <LABEL index="1" value="-29.4" />
      <LABEL index="2" value="-18.8" />
      <LABEL index="3" value="-8.1" />
      <LABEL index="4" value="2.5" />
      <LABEL index="5" value="13.1" />
      <LABEL index="6" value="23.8" />
      <LABEL index="7" value="34.4" />
      <LABEL index="8" value="45.0" />
      <LABEL index="9" value="55.6" />
      <LABEL index="10" value="66.2" />
      <LABEL index="11" value="76.9" />
      <LABEL index="12" value="87.5" />
      <LABEL index="13" value="98.1" />
      <LABEL index="14" value="108.8" />
      <LABEL index="15" value="119.4" />
      <LABEL index="16" value="130.0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22920" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x735" flags="0x30">
    <title>Closed Loop Enable Delay vs Startup Coolant</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Run time before closed loop is allowed, vs coolant at start-up. Stock H3 60 s cold .. 3 s warm (E0184) Effect: raise = later closed loop Evidence: ledger:E0184, ledger:E0210, ledger:E0213, ledger:E0257, ledger:E0260, ledger:E1329, ledger:E1603</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x298A2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x736" flags="0x0">
    <title>Idle Airflow Learn - Restore Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn. How fast the working learned value is pulled toward the stored copy when the truck is moving above the speed and rpm limits. Stock 0.1; the stock speed limit is 255 km/h, so on stock it never runs. Effect: raise = faster pull back to the stored value Evidence: ledger:E0347, ledger:E1603</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29CC0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x737" flags="0x0">
    <title>Idle Airflow Learn - Restore Filter Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn: outside closed loop idle speed control the live learn value is pulled back toward the saved value only above this engine speed. Stock 0 rpm. Effect: raise = the restore filter needs more engine speed Evidence: ledger:E1106, ledger:E1603</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29CC8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x738" flags="0x0">
    <title>Idle Airflow Learn - Restore Filter Vehicle Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow learn: outside closed loop idle speed control the live learn value is pulled back toward the saved value only above this vehicle speed. Stock 255 km/h: the restore filter never runs. Effect: lower = the restore filter runs while driving above this speed Evidence: ledger:E1106, ledger:E1603</description>
    <CATEGORYMEM index="0" category="5" />
    <EMBEDDEDDATA mmedaddress="0x29CCA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x739" flags="0x30">
    <title>Idle Start-Up RPM Flare - Park/Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Extra desired idle rpm after a start (added to the desired idle vs coolant value, E0294) vs time since start (rows) and coolant (columns), Park/Neutral. Stock 200 rpm at start (450 rpm at 20 and 32 C) decaying to 0 by 64 s. The Idle Airflow vs Start-Up RPM Flare table supplies the air for it; after 8 s it is cancelled once the truck moves or the throttle opens. Effect: raise = higher, longer rpm flare after starting Evidence: ledger:E0286, ledger:E0287, ledger:E0294, ledger:E1603</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>s since start</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="4" />
      <LABEL index="2" value="8" />
      <LABEL index="3" value="12" />
      <LABEL index="4" value="16" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="24" />
      <LABEL index="7" value="28" />
      <LABEL index="8" value="32" />
      <LABEL index="9" value="36" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="44" />
      <LABEL index="12" value="48" />
      <LABEL index="13" value="52" />
      <LABEL index="14" value="56" />
      <LABEL index="15" value="60" />
      <LABEL index="16" value="64" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2AE38" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x73A" flags="0x30">
    <title>Desired idle vs coolant temp - PARK/NEUTRAL</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Target idle speed vs engine coolant temperature in park or neutral. Higher than the in-gear target at 20 and 32 C (850 vs 750 rpm); the two curves are identical above 44 C. Warm-up log matches the part of the curve shared with the other idle curve (186 samples at 47-88 C, mean error 4.7 rpm, E0115). Which curve is Park/Neutral and which is in-gear rests on code (E0123). Evidence: ledger:E0048, ledger:E0115, ledger:E0123, ledger:E0158, ledger:E0223, ledger:E0231, ledger:E1603</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC coolant</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2ABB4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>8191.875000</max>
      <MATH equation="X/8"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x73B" flags="0x0">
    <title>MAP Circuit Low - Low Reading Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit low monitor (P0107, and P1107 for intermittent faults): with the ignition on, at or below the engine speed limit, or above it with throttle area at or above the area limit, each MAP sensor reading below the low voltage threshold counts as a low sample. The raw reading does not depend on the MAP sensor gain and offset. This is the low reading threshold in raw sensor counts (65535 = full scale). Stock 328 (0.5 % of full scale). Effect: raise = a higher sensor reading already counts as low Evidence: ledger:E0434, ledger:E0887, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3885E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>A/D counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x73C" flags="0x0">
    <title>Minimum RPM Run Latch</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. RPM threshold that permanently latches a run-detected flag for the remainder of the key cycle once engine speed climbs above it. Stock 50 rpm. Effect: raise = engine must spin faster before the latch sets; lower = the latch sets sooner Evidence: ledger:E0583, ledger:E1603</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x3513C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x73D" flags="0x0">
    <title>Misfire - Overspeed Pause Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Misfire monitor: engine speed at or above which the overspeed pause is requested. The pause length is zero in the stock calibration, so this has no effect. Stock 7200 rpm. Effect: no effect while the overspeed pause length is zero Evidence: ledger:E1065, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A9E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x73E" flags="0x30">
    <title>O2 Heater Turn-On Delay vs Startup Coolant - Downstream Sensor</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How long after engine start the downstream O2 sensor heater stays off (apart from a brief measuring pulse each second), by coolant temperature at start-up. The delay protects a cold sensor from water in the exhaust. Stock 208 s at -16 C and below, 45 s at 8 C, 15 s up to 44 C, 1 s from 56 C. Effect: lower = the heater comes on sooner after a cold start Evidence: ledger:E1019, ledger:E1020, ledger:E1603</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (startup coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2CB58" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>409.593750</max>
      <MATH equation="X/160"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x73F" flags="0x0">
    <title>Output Speed Sensor - Pulse Loss Updates to Zero (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. With the pulse loss handling switched on, each update without an output shaft speed sensor pulse lowers the output speed reading to what one pulse over the elapsed time would mean, and after this many updates without a pulse the reading is 0. Stock 0. The pulse loss handling is switched off on the stock calibration. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1511, ledger:E1603</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FB2A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x740" flags="0x0">
    <title>Over-RPM Status Flag RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine speed at or above which the PCM sets its over-rpm status flag. It is a reported status only: it does not cut fuel, spark or throttle. Stock 6600 rpm. Effect: raise = the over-rpm status sets at a higher rpm Evidence: ledger:E0022, ledger:E0143, ledger:E0151, ledger:E0195, ledger:E0987, ledger:E1603</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22B64" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x741" flags="0x0">
    <title>P0102 Check - MAF Frequency Low Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAF sensor circuit low check P0102: a sample counts as low when the MAF output frequency is at or below this. Stock 100 Hz. Effect: raise = higher frequencies already count as low Evidence: ledger:E1032, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x386AA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Hz</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>16383.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x742" flags="0x0">
    <title>P0103 Check - MAF Frequency High Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAF sensor circuit high check P0103: a sample counts as high when the MAF output frequency is at or above this. Stock 11000 Hz. Effect: raise = higher frequencies are tolerated before a sample counts as high Evidence: ledger:E1032, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x386A8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Hz</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>16383.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x743" flags="0x0">
    <title>P0130 Check Enable - Coolant Temp Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): only runs with coolant temperature at or above this. Stock 70 C. Effect: lower = the check can run on a cooler engine Evidence: ledger:E1004, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x398C4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x744" flags="0x0">
    <title>P0130 Check Enable - Airflow Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): only samples while mass airflow is at or below this. Stock 50 g/s. Effect: raise = the check also samples at higher airflow Evidence: ledger:E1004, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x398D2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x745" flags="0x0">
    <title>P0130 Check Enable - Airflow Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): only samples while mass airflow is at or above this. Stock 10 g/s. Effect: raise = the check needs more airflow Evidence: ledger:E1004, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x398D0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x746" flags="0x0">
    <title>P0130 Check Enable - RPM Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): only samples while engine speed is at or below this. Stock 3400 rpm. Effect: raise = the check also samples at higher rpm Evidence: ledger:E1004, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x398CE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x747" flags="0x0">
    <title>P0130 Check Enable - RPM Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): only samples while engine speed is at or above this. Stock 1000 rpm. Effect: raise = the check needs a higher rpm Evidence: ledger:E1004, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x398CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x748" flags="0x0">
    <title>P0130 Check Enable - Engine Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Upstream O2 sensor not-ready check (P0130): only runs once the engine has been running at least this long. Stock 200 s. Effect: lower = the check can start sooner after a start Evidence: ledger:E1004, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x398C2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x749" flags="0x30">
    <title>P0134 / P0140 Check - Inactive Voltage Band Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor activity check (P0134 upstream, P0140 downstream): a sample counts as inactive when the sensor reads above this and below the band high limit. Stock 400 mV upstream, 425 mV downstream. The array has room for four O2 sensors; this engine has two, so the third and fourth values are never used. Effect: raise = the inactive band gets narrower Evidence: ledger:E0995, ledger:E1561, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>4</indexcount>
      <units>sensor</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="sensor 1 (upstream)" />
      <LABEL index="1" value="sensor 2 (downstream)" />
      <LABEL index="2" value="sensor 3 (not fitted, unused)" />
      <LABEL index="3" value="sensor 4 (not fitted, unused)" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3668A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="4" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>mV</units>
      <decimalpl>2</decimalpl>
      <min>-2048.000000</min>
      <max>2047.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x74A" flags="0x0">
    <title>P0140 Early Pass - Voltage Band Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. O2 sensor activity check, early pass for the downstream sensor (P0140): a sample is inactive while the sensor reads above this and below the band high limit. Stock 300 mV. Effect: raise = lower readings count as active Evidence: ledger:E0995, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x36686" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>mV</units>
    <decimalpl>2</decimalpl>
    <min>-2048.000000</min>
    <max>2047.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x74B" flags="0x30">
    <title>P0230 Circuit Check - Fault Count and Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Fuel pump relay circuit check P0230: the code sets once the first value&#x27;s number of faulted samples is reached; if the second value&#x27;s number of samples is reached first, the check passes and both counts start again. Stock 10 and 12. Effect: raise the first value = more faulted samples are needed to set the code; raise the second = each window is longer Evidence: ledger:E1058, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>2</indexcount>
      <units>value</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="fault samples to fail" />
      <LABEL index="1" value="window samples to pass" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x37F70" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="2" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>samples</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x74C" flags="0x0">
    <title>P0336 Fail - Crank Resyncs per Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0336 (crank position sensor performance): the code sets when the crank signal has to be resynchronised this many times or more within one check window. Stock 20. Effect: raise = more crank resynchronisations are tolerated Evidence: ledger:E1080, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x367E8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>resyncs</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x74D" flags="0x0">
    <title>P0462 Fuel Level Sensor Low - Voltage Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0462 (fuel level sensor circuit low) counts time while the fuel level sender reads below this voltage. Stock 0.53 V. Effect: lower = a lower sender voltage is needed to count toward P0462 Evidence: ledger:E0957, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20348" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>9.999847</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/6553.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x74E" flags="0x0">
    <title>P0463 Fuel Level Sensor High - Voltage Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0463 (fuel level sensor circuit high) counts time while the fuel level sender reads above this voltage. Stock 3.5 V. Effect: raise = a higher sender voltage is needed to count toward P0463 Evidence: ledger:E0957, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x20346" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>9.999847</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/6553.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x74F" flags="0x0">
    <title>P0503 Test - Run Condition, Input Speed Step Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0503 (output speed sensor signal drop): the check runs only while transmission input speed changes by no more than this between two 25 ms samples; a larger step stops it for that sample and restarts the steady time. Stock 500 rpm. Effect: lower = the check is suspended by smaller input speed changes Evidence: ledger:E1293, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3FD0E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>-4096.000000</min>
    <max>4095.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x750" flags="0x0">
    <title>P0506 - Idle Spark Correction Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0506 (idle rpm lower than expected) counts toward a fail while the idle spark correction, the spark the PCM adds to pull a low idle back up, is above this. Stock 50 deg, which the stock idle spark curves (up to 21 deg) never reach. Effect: lower = P0506 can set at a smaller idle spark correction Evidence: ledger:E0990, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3803E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x751" flags="0x0">
    <title>P0506 Idle Speed Low - Fail Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the idle speed must stay below the low speed error threshold before one P0506 fail period is counted. Stock 5 s. Part of the idle speed diagnostic (P0506 idle speed lower than expected, P0507 higher than expected), which runs only once its enable conditions are met. Effect: raise = longer underspeed needed per fail period Evidence: ledger:E0639, ledger:E1239, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37FDC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x752" flags="0x0">
    <title>P0506 / P0507 - Fail Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0506 / P0507 count a failure once the idle spark correction has stayed beyond its threshold for this long. Stock 12.75 s. Effect: raise = the idle speed codes take longer to set Evidence: ledger:E0990, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38042" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>12.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x753" flags="0x0">
    <title>P0507 Idle Speed High - Fail Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Time the idle speed must stay above the high speed error threshold before one P0507 fail period is counted. Stock 15 s. Part of the idle speed diagnostic (P0506 idle speed lower than expected, P0507 higher than expected), which runs only once its enable conditions are met. Effect: raise = longer overspeed needed per fail period Evidence: ledger:E0639, ledger:E1239, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37FDA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x754" flags="0x0">
    <title>P0507 - Idle Spark Correction Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0507 (idle rpm higher than expected) counts toward a fail while the idle spark correction, the spark the PCM removes to pull a high idle back down, is below this. Stock -20 deg, which the stock idle spark curves (down to -9 deg) never reach. Effect: raise (toward 0) = P0507 can set at a smaller idle spark correction Evidence: ledger:E0990, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38040" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>deg</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x755" flags="0x0">
    <title>P0641 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor reference voltage A check (P0641): the code also sets once this many samples in a counting window are out of range. Stock 20. Effect: raise = more out of range samples are needed to set the code Evidence: ledger:E1033, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x31AE6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x756" flags="0x0">
    <title>P0641 Fail - Continuous Fault Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor reference voltage A check (P0641): the code sets once the reference voltage has been out of range continuously for this long. Stock 0.2 s. Effect: raise = a longer continuous fault is needed to set the code Evidence: ledger:E1033, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x31AE2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x757" flags="0x0">
    <title>P0641 Check - Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor reference voltage A check (P0641): the fault sample count starts again after this many samples. Stock 40. Effect: raise = each counting window is longer Evidence: ledger:E1033, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x31AE4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x758" flags="0x0">
    <title>P0651 Fail - Sample Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor reference voltage B check (P0651): the code also sets once this many samples in a counting window are out of range. Stock 20. Effect: raise = more out of range samples are needed to set the code Evidence: ledger:E1033, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x31AEC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x759" flags="0x0">
    <title>P0651 Fail - Continuous Fault Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor reference voltage B check (P0651): the code sets once the reference voltage has been out of range continuously for this long. Stock 0.2 s. Effect: raise = a longer continuous fault is needed to set the code Evidence: ledger:E1033, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x31AE8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x75A" flags="0x0">
    <title>P0651 Check - Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Sensor reference voltage B check (P0651): the fault sample count starts again after this many samples. Stock 40. Effect: raise = each counting window is longer Evidence: ledger:E1033, ledger:E1603</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x31AEA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x75B" flags="0x0">
    <title>PE Delay - Maximum Delay Store</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PE delay store fills with time spent out of power enrichment, up to this cap, and must drain before a delayed PE request takes effect. It drains at the rate set by the PE Delay Countdown Rate table. Stock 14.0 s. Effect: lower = shorter maximum PE delay; 0 = no delay Evidence: ledger:E0307, ledger:E1603</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x295DC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x75C" flags="0x30">
    <title>Power Enrichment EQ vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded fuel mixture during power enrichment, by engine speed (EQ: 1.0 = stoichiometric, higher = richer, lambda = 1 / EQ). This is the only power enrichment mixture table and it has no load or manifold pressure input: under boost every boost level gets the same mixture at a given rpm. The PCM commands the richest of power enrichment, catalyst over-temperature protection and coolant over-temperature enrichment. Stock about 1.20 at 4000 rpm. Effect: raise = richer full-load mixture at that rpm (at every boost level) Evidence: ledger:E0030, ledger:E0041, ledger:E0126, ledger:E0175, ledger:E0257, ledger:E0260, ledger:E0832, le...</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29856" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x75D" flags="0x30">
    <title>Rev limit ECT modifier (Q15 multiplier on the rev limit)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Evidence: ledger:E0034, ledger:E0109, ledger:E0131, ledger:E0168, ledger:E0260, ledger:E1603</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (ECT blended toward IAT when cold)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22B9C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor (0.75 cold .. 1.00 warm)</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x75E" flags="0x0">
    <title>RPM Limiter - Engage RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The limiter / rpm control block becomes active once rpm exceeds this (when its enable flags are set). Stock 1100 rpm. Effect: raise = block engages at higher rpm Evidence: ledger:E0325, ledger:E1603</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22EEA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x75F" flags="0x0">
    <title>RPM Limiter - Release RPM (after release)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Release threshold used once released, for hysteresis. Stock 650 rpm. Effect: keep above the release rpm Evidence: ledger:E0325, ledger:E1603</description>
    <CATEGORYMEM index="0" category="4" />
    <EMBEDDEDDATA mmedaddress="0x22EEE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x760" flags="0x0">
    <title>Traction Control Gear Request - Arming Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. Time the arming condition must add up to before the gear request is armed and its conditions are checked (stock 0.25 s). Part of the traction control gear request, which is switched off on this calibration and is not applied to the shift schedule, so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0506, ledger:E0925, ledger:E1114, ledger:E1440, ledger...</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3029A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x761" flags="0x0">
    <title>Torque Model - Engine Acceleration Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine torque model: share of each new engine acceleration reading taken into the filtered acceleration that the inertia torque is worked out from. Stock 0.5; 1.0 = no filtering. Effect: raise = the inertia torque follows engine speed changes faster Evidence: ledger:E1114, ledger:E1603</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3031C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>factor</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x762" flags="0x0">
    <title>Torque Reduction Cylinder Cut - Restore Hysteresis</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. Torque reduction with cylinder cut: a cut cylinder is given back only when the torque request needs this much more than the cylinders now fuelled. Stock 0.25 of a cylinder. Dormant on the stock calibration: the fewest fuelled cylinders curve is 5 everywhere, so no cylinder is ever cut. Effect: raise = cut cylinders come back later Evidence: ledger:E1133, ledger:E1603</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x3155E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>cylinders</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>15.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x763" flags="0x0">
    <title>Deceleration Flag - Acceleration Filter Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Filter gain for the acceleration the deceleration flag checks (stock 0.1 per update). A deceleration flag, read by the shift and converter clutch logic, is set while smoothed trans-side vehicle acceleration is below the lower limit or above the upper limit for the next gear down. Effect: raise = the deceleration flag reacts faster Evidence: ledger:E1299, ledger:E1603</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FB48" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x764" flags="0x0">
    <title>Transmission Diagnostics Enable - System Voltage High</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most transmission diagnostics (fluid temperature sensor, turbine speed, pressure switch, TCC and gear ratio tests) only run while system voltage is at or below this. Stock 18.0 V. Effect: lower = transmission diagnostics stop at a lower voltage Evidence: ledger:E0977, ledger:E1603</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FD22" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x765" flags="0x0">
    <title>Transmission Diagnostics Enable - System Voltage Low</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Most transmission diagnostics (fluid temperature sensor, turbine speed, pressure switch, TCC and gear ratio tests) only run while system voltage is at or above this. Stock 8.0 V. Effect: raise = transmission diagnostics need a higher voltage to run Evidence: ledger:E0977, ledger:E1603</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3FD24" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>V</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x766" flags="0x30">
    <title>Transient Fuel Evaporation RPM Gain</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. A Q15 multiplicative gain (32768 raw = 1.0, no correction), indexed by engine speed, on the evaporation fraction of the port-wall wetting (wall-film / puddle) fuel model: the fraction of the fuel puddle on the intake port wall that evaporates back into the airstream each update. Feeds directly into the model&#x27;s evaporation-fraction coefficient alongside a MAP x temperature table, through the standard Q15 shift-15 helper. Stock is a uniform 1.0 (no correction) from 0 to 6400 rpm. Effect: raise = more of the fuel puddle evaporates back into the airstream at that engine speed Evidence: ledger:E0755, ledger:E1603</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26B70" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw (Q15, 32768 = 1.0)</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x767" flags="0x0">
    <title>Fuel Level 2 - Sender Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Second fuel level value (used by the starter low-voltage hold and sent in a data message): how fast its filtered sender voltage follows the raw reading, as the fraction of the gap closed per update. Stock 0.80. Effect: lower = the sender reading is smoothed more (slower to change) Evidence: ledger:E1036, ledger:E1603</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x20354" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x768" flags="0x0">
    <title>Fuel Level Sender Filter</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. How fast the PCM&#x27;s filtered fuel level sender voltage follows the raw reading: the fraction of the gap closed per update. Stock 0.99 (almost no filtering). Effect: lower = the sender reading is smoothed more (slower to change) Evidence: ledger:E0956, ledger:E1603</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x37F22" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>fraction per update</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>0.999985</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/65536"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x769" flags="0x0">
    <title>Vehicle Bus - Class 2 Message 4B11 Minimum Interval</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. The PCM sends this percentage to another module on the vehicle bus (Class 2 message 4B11 / 4A11, byte 1, full scale 100 %); which module receives it, and what that module does with it, has not been determined, so the receiver is not established. The PCM itself does not use the value. A new message goes out once the value has changed by the change threshold since the last one sent and at least this long has passed. Stock 0.5 s. Effect: raise = less frequent updates Evidence: ledger:E1243, ledger:E1246, ledger:E1603</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2022A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x76A" flags="0x0">
    <title>P0464 Pass - Sample Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0464 (fuel level sensor intermittent, judged by the engine-off EVAP test): a pass is reported after this many samples unless the bad sample limit was exceeded first. Stock 3. Effect: raise = each decision window is longer Evidence: ledger:E1051, ledger:E1609</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35FF6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x76B" flags="0x0">
    <title>P0507 Fail - Period Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0507 (idle rpm higher than expected) sets once this many fail periods have been counted (each period is one P0506 / P0507 fail time with the idle spark correction beyond its threshold). Stock 1. Effect: raise = more fail periods are needed to set P0507 Evidence: ledger:E1033, ledger:E1609</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38026" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x76C" flags="0x0">
    <title>Closed Loop Slow-Sensor Tables - Minimum O2 Switch Count (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. Closed loop fuel: when the O2 response test counted fewer rich to lean or lean to rich switches than this, the slow sensor tables are used on both sides and the size of the O2 excursion is ignored (the trim then steps at the zero error interval and the purge feedback gets no O2 signal) until a later response test passes. Dormant on the stock calibration: 0 switches, so it never acts. Effect: raise = a sensor that switches rarely in the response test is treat...</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x25180" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>switches</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x76D" flags="0x0">
    <title>A/C Cut on 3-2 Kickdown - Pedal Above (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. When the transmission downshifts from 3rd to 2nd with the accelerator pedal above this, the A/C compressor is cut for the cut time. Stock 100 %. The cut is held off on this truck: stock 100 % pedal can never be exceeded, so this value has no effect (dormant). Effect: lower = the A/C is cut on 3-2 kickdowns at this pedal and above Evidence: ledger:E1540, ledger:E1609</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3F8AC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>200.003052</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.67"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x76E" flags="0x0">
    <title>A/C Cut on 3-2 Kickdown - Cut Time (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this calibration also leaves the code that reads this item inactive (checked by running this operating system&#x27;s code), as described below for the H3. How long the A/C compressor stays cut after a 3-2 kickdown. Stock 0 s. The cut is held off on this truck: stock 100 % pedal can never be exceeded, so this value has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1540, ledger:E1609</description>
    <CATEGORYMEM index="0" category="10" />
    <EMBEDDEDDATA mmedaddress="0x3F8AE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x76F" flags="0x30">
    <title>Knock Detection - Threshold Gain, Slot 2</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection (safety relevant). Threshold gain for knock loop slot 2 (the slot is the position in the knock module&#x27;s per-cylinder loop), by airmass (rows) and rpm (columns). The knock threshold is the background level plus this gain times the knock noise deviation, so 1.0 means one noise deviation above background. Stock 4.00 to 5.50. Raising it makes knock detection less sensitive. Effect: raise = a stronger knock signal is needed before knock retard (less sensitive) Evidence: ledger:E0364, ledger:E0703, ledger:E1674</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="500" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1500" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2500" />
      <LABEL index="6" value="3000" />
      <LABEL index="7" value="3500" />
      <LABEL index="8" value="4000" />
      <LABEL index="9" value="4500" />
      <LABEL index="10" value="5000" />
      <LABEL index="11" value="5500" />
      <LABEL index="12" value="6000" />
      <LABEL index="13" value="6500" />
      <LABEL index="14" value="7000" />
      <LABEL index="15" value="7500" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>g/cyl (airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.24" />
      <LABEL index="1" value="0.3" />
      <LABEL index="2" value="0.36" />
      <LABEL index="3" value="0.42" />
      <LABEL index="4" value="0.48" />
      <LABEL index="5" value="0.54" />
      <LABEL index="6" value="0.6" />
      <LABEL index="7" value="0.66" />
      <LABEL index="8" value="0.72" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x320FE" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain (x knock noise)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>127.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x770" flags="0x30">
    <title>Knock Detection - Threshold Gain, Slot 3</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection (safety relevant). Threshold gain for knock loop slot 3 (the slot is the position in the knock module&#x27;s per-cylinder loop), by airmass (rows) and rpm (columns). The knock threshold is the background level plus this gain times the knock noise deviation, so 1.0 means one noise deviation above background. Stock 2.75 to 3.50. Raising it makes knock detection less sensitive. Effect: raise = a stronger knock signal is needed before knock retard (less sensitive) Evidence: ledger:E0364, ledger:E0703, ledger:E1674</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="500" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1500" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2500" />
      <LABEL index="6" value="3000" />
      <LABEL index="7" value="3500" />
      <LABEL index="8" value="4000" />
      <LABEL index="9" value="4500" />
      <LABEL index="10" value="5000" />
      <LABEL index="11" value="5500" />
      <LABEL index="12" value="6000" />
      <LABEL index="13" value="6500" />
      <LABEL index="14" value="7000" />
      <LABEL index="15" value="7500" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>g/cyl (airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.24" />
      <LABEL index="1" value="0.3" />
      <LABEL index="2" value="0.36" />
      <LABEL index="3" value="0.42" />
      <LABEL index="4" value="0.48" />
      <LABEL index="5" value="0.54" />
      <LABEL index="6" value="0.6" />
      <LABEL index="7" value="0.66" />
      <LABEL index="8" value="0.72" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x32234" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain (x knock noise)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>127.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x771" flags="0x30">
    <title>Knock Detection - Threshold Gain, Slot 4</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Knock detection (safety relevant). Threshold gain for knock loop slot 4 (the slot is the position in the knock module&#x27;s per-cylinder loop), by airmass (rows) and rpm (columns). The knock threshold is the background level plus this gain times the knock noise deviation, so 1.0 means one noise deviation above background. Stock 3.25 to 4.50. Raising it makes knock detection less sensitive. Effect: raise = a stronger knock signal is needed before knock retard (less sensitive) Evidence: ledger:E0364, ledger:E0703, ledger:E1674</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="500" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1500" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2500" />
      <LABEL index="6" value="3000" />
      <LABEL index="7" value="3500" />
      <LABEL index="8" value="4000" />
      <LABEL index="9" value="4500" />
      <LABEL index="10" value="5000" />
      <LABEL index="11" value="5500" />
      <LABEL index="12" value="6000" />
      <LABEL index="13" value="6500" />
      <LABEL index="14" value="7000" />
      <LABEL index="15" value="7500" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>g/cyl (airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.24" />
      <LABEL index="1" value="0.3" />
      <LABEL index="2" value="0.36" />
      <LABEL index="3" value="0.42" />
      <LABEL index="4" value="0.48" />
      <LABEL index="5" value="0.54" />
      <LABEL index="6" value="0.6" />
      <LABEL index="7" value="0.66" />
      <LABEL index="8" value="0.72" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3236A" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain (x knock noise)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>127.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x772" flags="0x30">
    <title>Knock Detection - Threshold Gain, Slot 5 (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: the knock loop runs once per cylinder and this calibration has 4 cylinders, so only slots 1 to 4 are read; this slot is never used here (dormant). Knock detection (safety relevant). Threshold gain for knock loop slot 5 (the slot is the position in the knock module&#x27;s per-cylinder loop), by airmass (rows) and rpm (columns). The knock threshold is the background level plus this gain times the knock noise deviation, so 1.0 means one noise deviation above background. Stock 4.00 to 5.50. Raising it makes knock detection less sensitive. Effect: raise = a stronger knock signal is needed before knock retard (less...</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="500" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1500" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2500" />
      <LABEL index="6" value="3000" />
      <LABEL index="7" value="3500" />
      <LABEL index="8" value="4000" />
      <LABEL index="9" value="4500" />
      <LABEL index="10" value="5000" />
      <LABEL index="11" value="5500" />
      <LABEL index="12" value="6000" />
      <LABEL index="13" value="6500" />
      <LABEL index="14" value="7000" />
      <LABEL index="15" value="7500" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>g/cyl (airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.24" />
      <LABEL index="1" value="0.3" />
      <LABEL index="2" value="0.36" />
      <LABEL index="3" value="0.42" />
      <LABEL index="4" value="0.48" />
      <LABEL index="5" value="0.54" />
      <LABEL index="6" value="0.6" />
      <LABEL index="7" value="0.66" />
      <LABEL index="8" value="0.72" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x324A0" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain (x knock noise)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>127.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x773" flags="0x30">
    <title>Knock Detection - Threshold Gain, Slot 6 (6-cylinder only, dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: the knock loop runs once per cylinder and this calibration has 4 cylinders, so only slots 1 to 4 are read; this slot is never used here (dormant). Knock detection (safety relevant). Threshold gain for knock loop slot 6, by airmass (rows) and rpm (columns), in the same unit as slots 1 to 5: the knock threshold is the background level plus this gain times the knock noise deviation. The loop runs once per cylinder, so only a 6-cylinder calibration reads this slot; the 5-cylinder H3 never does. Dormant: no effect on this truck&#x27;s software. Effect: no effect on this truck Evidence: ledger:E0364, ledger:E0703, l...</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="500" />
      <LABEL index="2" value="1000" />
      <LABEL index="3" value="1500" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2500" />
      <LABEL index="6" value="3000" />
      <LABEL index="7" value="3500" />
      <LABEL index="8" value="4000" />
      <LABEL index="9" value="4500" />
      <LABEL index="10" value="5000" />
      <LABEL index="11" value="5500" />
      <LABEL index="12" value="6000" />
      <LABEL index="13" value="6500" />
      <LABEL index="14" value="7000" />
      <LABEL index="15" value="7500" />
      <LABEL index="16" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>g/cyl (airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.24" />
      <LABEL index="1" value="0.3" />
      <LABEL index="2" value="0.36" />
      <LABEL index="3" value="0.42" />
      <LABEL index="4" value="0.48" />
      <LABEL index="5" value="0.54" />
      <LABEL index="6" value="0.6" />
      <LABEL index="7" value="0.66" />
      <LABEL index="8" value="0.72" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x325D6" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>gain (x knock noise)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>127.998047</max>
      <MATH equation="X/512"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x774" flags="0x30">
    <title>Cranking FA Mult Stage 1 vs. Cranking Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Evidence: ledger:E0148, ledger:E0162, ledger:E0163, ledger:E0167, ledger:E0196, ledger:E0213, ledger:E0221, ledger:E0236, ledger:E0257, ledger:E0260, ledger:E0785, ledger:E1329, ledger:E1684</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>s (engine-off soak time)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="5" />
      <LABEL index="3" value="10" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="30" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="120" />
      <LABEL index="8" value="240" />
      <LABEL index="9" value="600" />
      <LABEL index="10" value="1200" />
      <LABEL index="11" value="1800" />
      <LABEL index="12" value="3600" />
      <LABEL index="13" value="7200" />
      <LABEL index="14" value="10800" />
      <LABEL index="15" value="14400" />
      <LABEL index="16" value="21600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <EMBEDDEDDATA mmedaddress="0x26E1C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26BA8" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X*0.0009765625"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x775" flags="0x30">
    <title>Throttle area -&gt; throttle position model</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Converts throttle-area demand to desired throttle position (and back, elsewhere). Shared by ETC and the transmission shift-throttle path. DO NOT TUNE - changing it shifts every pedal, idle and shift-throttle relationship at once (E0228, E0239) Effect: throttle geometry model Evidence: ledger:E0228, ledger:E0239, ledger:E1329, ledger:E1339, ledger:E1684</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>% throttle area</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.081" />
      <LABEL index="1" value="0.137" />
      <LABEL index="2" value="0.159" />
      <LABEL index="3" value="0.212" />
      <LABEL index="4" value="0.253" />
      <LABEL index="5" value="0.304" />
      <LABEL index="6" value="0.366" />
      <LABEL index="7" value="0.462" />
      <LABEL index="8" value="0.598" />
      <LABEL index="9" value="0.79" />
      <LABEL index="10" value="1.076" />
      <LABEL index="11" value="1.369" />
      <LABEL index="12" value="1.709" />
      <LABEL index="13" value="2.148" />
      <LABEL index="14" value="2.904" />
      <LABEL index="15" value="4.529" />
      <LABEL index="16" value="7.265" />
      <LABEL index="17" value="9.52" />
      <LABEL index="18" value="11.375" />
      <LABEL index="19" value="13.773" />
      <LABEL index="20" value="16.441" />
      <LABEL index="21" value="19.824" />
      <LABEL index="22" value="23.465" />
      <LABEL index="23" value="27.812" />
      <LABEL index="24" value="33.119" />
      <LABEL index="25" value="41.11" />
      <LABEL index="26" value="51.836" />
      <LABEL index="27" value="61.595" />
      <LABEL index="28" value="70.415" />
      <LABEL index="29" value="77.992" />
      <LABEL index="30" value="84.996" />
      <LABEL index="31" value="92.213" />
      <LABEL index="32" value="99.998" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x23F4A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x776" flags="0x30">
    <title>Engine Torque Estimate vs Throttle x RPM (throttle-based model)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Gross torque the PCM predicts from throttle area and rpm, before the baro and intake air temperature multipliers and minus losses and inertia; the electronic throttle&#x27;s torque control and others read it. Rows are the total throttle area request (idle plus pedal), in % of full throttle area. Stock 0 at closed throttle up to 400 Nm. Model: do not edit to change power. Effect: DO NOT EDIT (torque model) Evidence: ledger:E0377, ledger:E0452, ledger:E0927, ledger:E0936, ledger:E1684</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8191" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>% throttle area</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="0.2" />
      <LABEL index="2" value="0.4" />
      <LABEL index="3" value="0.6" />
      <LABEL index="4" value="0.8" />
      <LABEL index="5" value="1" />
      <LABEL index="6" value="1.199" />
      <LABEL index="7" value="1.401" />
      <LABEL index="8" value="1.601" />
      <LABEL index="9" value="1.801" />
      <LABEL index="10" value="2.001" />
      <LABEL index="11" value="2.5" />
      <LABEL index="12" value="3" />
      <LABEL index="13" value="3.501" />
      <LABEL index="14" value="4" />
      <LABEL index="15" value="5.001" />
      <LABEL index="16" value="6" />
      <LABEL index="17" value="7.001" />
      <LABEL index="18" value="8.001" />
      <LABEL index="19" value="9.001" />
      <LABEL index="20" value="10.002" />
      <LABEL index="21" value="12.001" />
      <LABEL index="22" value="14.001" />
      <LABEL index="23" value="16.002" />
      <LABEL index="24" value="18.001" />
      <LABEL index="25" value="20.002" />
      <LABEL index="26" value="25.003" />
      <LABEL index="27" value="30.004" />
      <LABEL index="28" value="35.004" />
      <LABEL index="29" value="40.004" />
      <LABEL index="30" value="45.005" />
      <LABEL index="31" value="50.005" />
      <LABEL index="32" value="100.009" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x31094" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>Nm</units>
      <decimalpl>1</decimalpl>
      <min>-8192.000000</min>
      <max>8191.750000</max>
      <MATH equation="X/4"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x777" flags="0x30">
    <title>Cruise Control - Resume Start Target Offset vs Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this operating system runs the same code and holds the same value as the H3 in its own value, which is what leaves this item without effect, so it stays inactive here too, as described below for the H3. Cruise control. Added to the target speed when resume is pressed below the set speed (in full from 0.5 km/h below the set speed), by vehicle speed. Stock all 0, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = resume starts with a higher target) Evidence: ledger:E1353, ledger:E1688</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.9" />
      <LABEL index="2" value="55.8" />
      <LABEL index="3" value="64.6" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.4" />
      <LABEL index="6" value="91.2" />
      <LABEL index="7" value="100.1" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.9" />
      <LABEL index="10" value="126.8" />
      <LABEL index="11" value="135.6" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.4" />
      <LABEL index="14" value="162.2" />
      <LABEL index="15" value="171.1" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21A3C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x778" flags="0x30">
    <title>Cruise Control - Target Speed Offset vs Speed (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this operating system runs the same code and holds the same value as the H3 in its own value, which is what leaves this item without effect, so it stays inactive here too, as described below for the H3. Cruise control: added to the vehicle speed when the cruise control takes its target speed (set and the matching resume step), by vehicle speed (38 to 180 km/h). Stock 0 at every speed, so the target is the speed itself. This has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration (raise = the cruise target is set above the current speed) Evidence: ledger:E0644, ledger:E0936,...</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.875" />
      <LABEL index="2" value="55.75" />
      <LABEL index="3" value="64.625" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.375" />
      <LABEL index="6" value="91.25" />
      <LABEL index="7" value="100.125" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.875" />
      <LABEL index="10" value="126.75" />
      <LABEL index="11" value="135.625" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.375" />
      <LABEL index="14" value="162.25" />
      <LABEL index="15" value="171.125" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21A18" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>km/h</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x779" flags="0x0">
    <title>Purge in Open Loop - Start-Up Coolant Split (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this operating system runs the same code and holds the same value as the H3 in the open loop purge switch, which is what leaves this item without effect, so it stays inactive here too, as described below for the H3. Start-up coolant temperature that picks the cold delay (below) or the warm delay (at or above). Stock 72 C. Part of an optional path that lets canister purge start while fuel control is still in open loop, after a run time delay chosen by start-up coolant temperature. This open loop purge path is switched off in the stock calibration, so this has no effect on the stock calibration (dormant). Effect...</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x245CC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x77A" flags="0x0">
    <title>Purge in Open Loop - Run Time Delay, Cold Start (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this operating system runs the same code and holds the same value as the H3 in the open loop purge switch, which is what leaves this item without effect, so it stays inactive here too, as described below for the H3. Engine run time before purge may start in open loop after a start below the coolant split. Stock 0 s. Part of an optional path that lets canister purge start while fuel control is still in open loop, after a run time delay chosen by start-up coolant temperature. This open loop purge path is switched off in the stock calibration, so this has no effect on the stock calibration (dormant). Effect: no e...</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x245C6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x77B" flags="0x0">
    <title>Purge in Open Loop - Run Time Delay, Warm Start (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this operating system runs the same code and holds the same value as the H3 in the open loop purge switch, which is what leaves this item without effect, so it stays inactive here too, as described below for the H3. Engine run time before purge may start in open loop after a start at or above the coolant split. Stock 0 s. Part of an optional path that lets canister purge start while fuel control is still in open loop, after a run time delay chosen by start-up coolant temperature. This open loop purge path is switched off in the stock calibration, so this has no effect on the stock calibration (dormant). Effect...</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x245C8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x77C" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Pressure Slope Limit (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this operating system runs the same code and holds the same value as the H3 in the test sub-state skips, which is what leaves this item without effect, so it stays inactive here too, as described below for the H3. Vapour check: a tank pressure rise slope at or above this means too much fuel vapour, and the test stops. Stock 0.024 inH2O/s. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554, ledger:E1688</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37382" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O/s</units>
    <decimalpl>3</decimalpl>
    <min>-8.000000</min>
    <max>7.999756</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4096"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x77D" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Start Vacuum (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this operating system runs the same code and holds the same value as the H3 in the test sub-state skips, which is what leaves this item without effect, so it stays inactive here too, as described below for the H3. Vapour check: the pressure measurement starts once tank vacuum is below this (negative = pressure). Stock -0.4 inH2O (0.4 inH2O pressure). Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554, ledger:E1688</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x37390" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>inH2O</units>
    <decimalpl>3</decimalpl>
    <min>-32.000000</min>
    <max>31.999023</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/1024"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x77E" flags="0x0">
    <title>EVAP Test (Engine Running) - Vapour Check Tracking Start (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this operating system runs the same code and holds the same value as the H3 in the test sub-state skips, which is what leaves this item without effect, so it stays inactive here too, as described below for the H3. Vapour check: time into the measurement from which the peak pressure is tracked for the slope. Stock 25 s. Engine-running EVAP test. Used only in the small leak part of the engine-running test, which the stock option words skip, so this use has no effect (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1554, ledger:E1688</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3738E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x77F" flags="0x30">
    <title>Idle Airflow Closed-Loop Mode 2 - Step vs MAP Error (dormant)</title>
    <description>Change in small steps and log. Packed table: the MARKER column is a structure byte (0x11 row marker), not data - never edit it. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this operating system runs the same code and holds the same value as the H3 in the idle closed loop mode select, which is what leaves this item without effect, so it stays inactive here too, as described below for the H3. Idle airflow integral step per update by manifold pressure error in the alternate (MAP based) closed-loop mode, the counterpart of Idle Airflow Closed-Loop Step vs Airflow Error. Row 1 = In Gear, row 2 = Park / Neutral. Stock all 0. Mode 2 runs only when the closed loop mode select is not 1; it is...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <EMBEDDEDDATA mmedaddress="0x29FDE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <indexcount>18</indexcount>
      <units>MARKER + data (header bytes: DO NOT EDIT; data columns: kPa MAP error)</units>
      <embedinfo type="1" />
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>2</indexcount>
      <units>transmission</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="In Gear" />
      <LABEL index="1" value="Park / Neutral" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29D88" mmedelementsizebits="16" mmedrowcount="2" mmedcolcount="18" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s per update</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x780" flags="0x30">
    <title>Idle Airflow Closed-Loop Mode 2 - MAP Error Breakpoints (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this operating system runs the same code and holds the same value as the H3 in the idle closed loop mode select, which is what leaves this item without effect, so it stays inactive here too, as described below for the H3. Manifold pressure error breakpoints (measured minus the mode 2 MAP target, after the error gain) for the mode 2 closed-loop step table. Stock -16 to +16 kPa in 2 kPa steps. Mode 2 runs only when the closed loop mode select is not 1; it is 1 on the stock calibration, so this has no effect on the stock calibration (dormant). Effect: no effect on the stock calibration Evidence: ledger:E1393, led...</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>cell of the mode 2 step table</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="3" />
      <LABEL index="3" value="4" />
      <LABEL index="4" value="5" />
      <LABEL index="5" value="6" />
      <LABEL index="6" value="7" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="9" />
      <LABEL index="9" value="10" />
      <LABEL index="10" value="11" />
      <LABEL index="11" value="12" />
      <LABEL index="12" value="13" />
      <LABEL index="13" value="14" />
      <LABEL index="14" value="15" />
      <LABEL index="15" value="16" />
      <LABEL index="16" value="17" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29FE0" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>kPa</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x781" flags="0x0">
    <title>Swap - Theft Deterrent (VATS) Code P1630 Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Swap setting. 1 (stock): the PCM runs its P1630 theft deterrent check and sets code P1630 when the theft deterrent status is not correct. 0: the check never runs, so P1630 is never set and never reported as passed. Use it on an engine swap with the theft deterrent fuel enable bypassed, so the swapped PCM is not left with P1630 from the missing body control module. P1630 is a non-emissions code that does not light the check engine lamp. No password or security data is read or changed. For use on your own engine swap only. Effect: 0 = P1630 check off (never set); 1 = stock Evidence: ledger:E0658, ledger:E1695, ledger:E1704</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x204E2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on (stock), 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x782" flags="0x0">
    <title>Swap - Theft Deterrent (VATS) Code P1631 Enable</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Swap setting. 1 (stock): the PCM runs its P1631 theft deterrent check and sets code P1631 when the theft deterrent status is not correct. 0: the check never runs, so P1631 is never set and never reported as passed. Use it on an engine swap with the theft deterrent fuel enable bypassed, so the swapped PCM is not left with P1631 from the missing body control module. P1631 is a non-emissions code that does not light the check engine lamp. No password or security data is read or changed. For use on your own engine swap only. Effect: 0 = P1631 check off (never set); 1 = stock Evidence: ledger:E0659, ledger:E1695, ledger:E1704</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x204E4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on (stock), 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x783" flags="0x30">
    <title>DTC Type and MIL per Code</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. One byte per trouble code (row labels), as in the 0411 DTC processing and MIL tables. The low two bits set the code&#x27;s type: 0 = not reported (the PCM never stores it); 1 = type A, stored on the first failure; 2 = type B, stored when the check fails on two trips in a row; 3 = type C, stored on the first failure and never lights the lamp. Add 4 to request the check engine lamp when the code is stored (types A and B only). Examples: 5 = type A with lamp, 6 = type B with lamp, 3 = stored without lamp, 0 = off. Types 0 and 3 also drop the code from its monitor&#x27;s readiness check: a monitor reports complete once all o...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>243</indexcount>
      <units>code</units>
      <embedinfo type="0" />
      <outputtype>4</outputtype>
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="P0000" />
      <LABEL index="1" value="P0016" />
      <LABEL index="2" value="P0017" />
      <LABEL index="3" value="P0018" />
      <LABEL index="4" value="P0019" />
      <LABEL index="5" value="P0030" />
      <LABEL index="6" value="P0033" />
      <LABEL index="7" value="P0036" />
      <LABEL index="8" value="P0050" />
      <LABEL index="9" value="P0053" />
      <LABEL index="10" value="P0054" />
      <LABEL index="11" value="P0056" />
      <LABEL index="12" value="P0059" />
      <LABEL index="13" value="P0060" />
      <LABEL index="14" value="P0069" />
      <LABEL index="15" value="P0096" />
      <LABEL index="16" value="P0097" />
      <LABEL index="17" value="P0098" />
      <LABEL index="18" value="P0101" />
      <LABEL index="19" value="P0102" />
      <LABEL index="20" value="P0103" />
      <LABEL index="21" value="P0106" />
      <LABEL index="22" value="P0107" />
      <LABEL index="23" value="P0108" />
      <LABEL index="24" value="P0111" />
      <LABEL index="25" value="P0112" />
      <LABEL index="26" value="P0113" />
      <LABEL index="27" value="P0116" />
      <LABEL index="28" value="P0117" />
      <LABEL index="29" value="P0118" />
      <LABEL index="30" value="P0121" />
      <LABEL index="31" value="P0122" />
      <LABEL index="32" value="P0123" />
      <LABEL index="33" value="P0125" />
      <LABEL index="34" value="P0128" />
      <LABEL index="35" value="P0130" />
      <LABEL index="36" value="P0131" />
      <LABEL index="37" value="P0132" />
      <LABEL index="38" value="P0133" />
      <LABEL index="39" value="P0134" />
      <LABEL index="40" value="P0135" />
      <LABEL index="41" value="P0136" />
      <LABEL index="42" value="P0137" />
      <LABEL index="43" value="P0138" />
      <LABEL index="44" value="P0140" />
      <LABEL index="45" value="P0141" />
      <LABEL index="46" value="P0142" />
      <LABEL index="47" value="P0150" />
      <LABEL index="48" value="P0151" />
      <LABEL index="49" value="P0152" />
      <LABEL index="50" value="P0153" />
      <LABEL index="51" value="P0154" />
      <LABEL index="52" value="P0155" />
      <LABEL index="53" value="P0156" />
      <LABEL index="54" value="P0157" />
      <LABEL index="55" value="P0158" />
      <LABEL index="56" value="P0160" />
      <LABEL index="57" value="P0161" />
      <LABEL index="58" value="P0171" />
      <LABEL index="59" value="P0172" />
      <LABEL index="60" value="P0174" />
      <LABEL index="61" value="P0175" />
      <LABEL index="62" value="P0201" />
      <LABEL index="63" value="P0202" />
      <LABEL index="64" value="P0203" />
      <LABEL index="65" value="P0204" />
      <LABEL index="66" value="P0205" />
      <LABEL index="67" value="P0206" />
      <LABEL index="68" value="P0207" />
      <LABEL index="69" value="P0208" />
      <LABEL index="70" value="P0222" />
      <LABEL index="71" value="P0223" />
      <LABEL index="72" value="P0230" />
      <LABEL index="73" value="P023A" />
      <LABEL index="74" value="P0300" />
      <LABEL index="75" value="P0325" />
      <LABEL index="76" value="P0326" />
      <LABEL index="77" value="P0327" />
      <LABEL index="78" value="P0332" />
      <LABEL index="79" value="P0335" />
      <LABEL index="80" value="P0336" />
      <LABEL index="81" value="P0340" />
      <LABEL index="82" value="P0341" />
      <LABEL index="83" value="P0345" />
      <LABEL index="84" value="P0346" />
      <LABEL index="85" value="P0351" />
      <LABEL index="86" value="P0352" />
      <LABEL index="87" value="P0353" />
      <LABEL index="88" value="P0354" />
      <LABEL index="89" value="P0355" />
      <LABEL index="90" value="P0356" />
      <LABEL index="91" value="P0357" />
      <LABEL index="92" value="P0358" />
      <LABEL index="93" value="P0365" />
      <LABEL index="94" value="P0366" />
      <LABEL index="95" value="P0385" />
      <LABEL index="96" value="P0386" />
      <LABEL index="97" value="P0390" />
      <LABEL index="98" value="P0391" />
      <LABEL index="99" value="P0420" />
      <LABEL index="100" value="P0430" />
      <LABEL index="101" value="P0455" />
      <LABEL index="102" value="P0442" />
      <LABEL index="103" value="P0443" />
      <LABEL index="104" value="P0446" />
      <LABEL index="105" value="P0449" />
      <LABEL index="106" value="P0451" />
      <LABEL index="107" value="P0452" />
      <LABEL index="108" value="P0453" />
      <LABEL index="109" value="P0454" />
      <LABEL index="110" value="P0461" />
      <LABEL index="111" value="P0462" />
      <LABEL index="112" value="P0463" />
      <LABEL index="113" value="P0464" />
      <LABEL index="114" value="P0480" />
      <LABEL index="115" value="P0481" />
      <LABEL index="116" value="P0482" />
      <LABEL index="117" value="P0502" />
      <LABEL index="118" value="P0503" />
      <LABEL index="119" value="P0506" />
      <LABEL index="120" value="P0507" />
      <LABEL index="121" value="P0512" />
      <LABEL index="122" value="P0522" />
      <LABEL index="123" value="P0523" />
      <LABEL index="124" value="P0532" />
      <LABEL index="125" value="P0533" />
      <LABEL index="126" value="P0562" />
      <LABEL index="127" value="P0563" />
      <LABEL index="128" value="P0564" />
      <LABEL index="129" value="P0567" />
      <LABEL index="130" value="P0568" />
      <LABEL index="131" value="P0572" />
      <LABEL index="132" value="P0573" />
      <LABEL index="133" value="P0601" />
      <LABEL index="134" value="P0602" />
      <LABEL index="135" value="P0603" />
      <LABEL index="136" value="P0604" />
      <LABEL index="137" value="P0606" />
      <LABEL index="138" value="P0607" />
      <LABEL index="139" value="P0615" />
      <LABEL index="140" value="P0621" />
      <LABEL index="141" value="P0622" />
      <LABEL index="142" value="P0650" />
      <LABEL index="143" value="P0700" />
      <LABEL index="144" value="P0703" />
      <LABEL index="145" value="P0833" />
      <LABEL index="146" value="P0719" />
      <LABEL index="147" value="P0722" />
      <LABEL index="148" value="P0723" />
      <LABEL index="149" value="P0724" />
      <LABEL index="150" value="P0831" />
      <LABEL index="151" value="P0851" />
      <LABEL index="152" value="P0852" />
      <LABEL index="153" value="P1101" />
      <LABEL index="154" value="P1106" />
      <LABEL index="155" value="P1107" />
      <LABEL index="156" value="P1111" />
      <LABEL index="157" value="P1112" />
      <LABEL index="158" value="P1114" />
      <LABEL index="159" value="P1115" />
      <LABEL index="160" value="P0120" />
      <LABEL index="161" value="P1123" />
      <LABEL index="162" value="P1124" />
      <LABEL index="163" value="P1133" />
      <LABEL index="164" value="P1134" />
      <LABEL index="165" value="P1153" />
      <LABEL index="166" value="P1154" />
      <LABEL index="167" value="P1182" />
      <LABEL index="168" value="P1183" />
      <LABEL index="169" value="P1184" />
      <LABEL index="170" value="P1185" />
      <LABEL index="171" value="P1186" />
      <LABEL index="172" value="P0520" />
      <LABEL index="173" value="P0220" />
      <LABEL index="174" value="P2135" />
      <LABEL index="175" value="P2138" />
      <LABEL index="176" value="P2120" />
      <LABEL index="177" value="P2125" />
      <LABEL index="178" value="P0315" />
      <LABEL index="179" value="P1372" />
      <LABEL index="180" value="P1380" />
      <LABEL index="181" value="P1381" />
      <LABEL index="182" value="P1400" />
      <LABEL index="183" value="P2066" />
      <LABEL index="184" value="P2067" />
      <LABEL index="185" value="P2068" />
      <LABEL index="186" value="P0496" />
      <LABEL index="187" value="P2176" />
      <LABEL index="188" value="P0068" />
      <LABEL index="189" value="P2101" />
      <LABEL index="190" value="P1516" />
      <LABEL index="191" value="P2119" />
      <LABEL index="192" value="P0645" />
      <LABEL index="193" value="P0856" />
      <LABEL index="194" value="P1574" />
      <LABEL index="195" value="P1575" />
      <LABEL index="196" value="P1621" />
      <LABEL index="197" value="P1630" />
      <LABEL index="198" value="P1631" />
      <LABEL index="199" value="P1633" />
      <LABEL index="200" value="P1634" />
      <LABEL index="201" value="P0641" />
      <LABEL index="202" value="P0651" />
      <LABEL index="203" value="P1680" />
      <LABEL index="204" value="P1681" />
      <LABEL index="205" value="P1682" />
      <LABEL index="206" value="P2610" />
      <LABEL index="207" value="P1689" />
      <LABEL index="208" value="P1700" />
      <LABEL index="209" value="P2025" />
      <LABEL index="210" value="P2026" />
      <LABEL index="211" value="P2027" />
      <LABEL index="212" value="P2122" />
      <LABEL index="213" value="P2123" />
      <LABEL index="214" value="P2127" />
      <LABEL index="215" value="P2128" />
      <LABEL index="216" value="P2227" />
      <LABEL index="217" value="P2228" />
      <LABEL index="218" value="P2229" />
      <LABEL index="219" value="P2261" />
      <LABEL index="220" value="P2A00" />
      <LABEL index="221" value="P2A01" />
      <LABEL index="222" value="P2A03" />
      <LABEL index="223" value="P2A04" />
      <LABEL index="224" value="P3400" />
      <LABEL index="225" value="U1040" />
      <LABEL index="226" value="U1056" />
      <LABEL index="227" value="U1064" />
      <LABEL index="228" value="U1065" />
      <LABEL index="229" value="U1066" />
      <LABEL index="230" value="U1088" />
      <LABEL index="231" value="U1096" />
      <LABEL index="232" value="U1152" />
      <LABEL index="233" value="U1192" />
      <LABEL index="234" value="U1300" />
      <LABEL index="235" value="U1301" />
      <LABEL index="236" value="U0001" />
      <LABEL index="237" value="U2101" />
      <LABEL index="238" value="U0100" />
      <LABEL index="239" value="U0101" />
      <LABEL index="240" value="U2107" />
      <LABEL index="241" value="U2108" />
      <LABEL index="242" value="U2139" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x35034" mmedelementsizebits="8" mmedrowcount="243" mmedcolcount="1" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>0 off, 1 A, 2 B, 3 C, add 4 for MIL</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x784" flags="0x0">
    <title>Crank Wheel - Teeth per Revolution (DO NOT EDIT)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Number of teeth per crankshaft revolution on the crank wheel, used to turn the measured tooth period into engine speed. Stock 60. Reference only: DO NOT EDIT. Effect: reference only (crank wheel geometry) Evidence: ledger:E0438, ledger:E0775, ledger:E1272, ledger:E1274, ledger:E1763</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x22CAC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>teeth per revolution</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>127.998047</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/512"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x785" flags="0x0">
    <title>Cam Sensor Fault Start - Running Time to Stand Down</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cranking strategy for a failed cam sensor: how long the engine must stay above the running engine speed before the strategy stands down for this start. Stock 0.6 s. Effect: raise = the strategy stays ready longer after the engine starts Evidence: ledger:E0324, ledger:E1274, ledger:E1275, ledger:E1763</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x22D4E" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x786" flags="0x0">
    <title>Cam Sensor Fault Start - Minimum Crank Time Before Fallback</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Cranking strategy for a failed cam sensor: with a cam sensor fault set, the crank / cam position decoding switches to its fallback mode once the crank time reaches this. Stock 0 s (switches at once). Effect: raise = the PCM cranks longer in its normal mode before switching to the fallback mode Evidence: ledger:E0324, ledger:E1274, ledger:E1275, ledger:E1763</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x22D50" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x787" flags="0x0">
    <title>Oil Life Reset - Press Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil life reset with the accelerator (key on, engine not turning): a press is counted when the throttle position signal rises above this. Stock 70 %. Effect: raise = the accelerator must be pressed further for a press to count Evidence: ledger:E1128, ledger:E1763</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2CF8A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>%</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>199.996948</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/327.68"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x788" flags="0x0">
    <title>Traction Control Gear Request - Cold Engine Torque Limit (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. With the engine at or below the traction control cold engine coolant temperature and the traction control torque limit below this (stock 300 Nm), the gear request uses its first set of conditions, the low throttle threshold and the long arming time; otherwise it uses the other two condition sets, the high throttle threshold and the short arming time. Part of the traction control gear request, which is switched off on this calibration and is not applied to the shift schedule, so this has no effect (dormant). Effect: no effect on this truck Evidence: ledger:E0504, ledger:E0918, ledger:E0925, ledger:E1114, ledger:E1440, ledger:E1763</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x30294" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>Nm</units>
    <decimalpl>1</decimalpl>
    <min>0.000000</min>
    <max>16383.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/4"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x789" flags="0x0">
    <title>P0125 / P0128 Fail - Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Coolant warm-up checks P0125 / P0128: the code sets after the failing condition (required air drawn, coolant still below the target) has been seen on this many one second passes. Stock 30. Effect: raise = the failing condition must last longer before the code sets Evidence: ledger:E1056, ledger:E1763</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x35194" mmedelementsizebits="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>count</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>255.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x78A" flags="0x30">
    <title>Cold Start Emission Monitor - Expected Idle Speed, In Gear (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this table has 9 rows and 17 columns on this operating system (from its own table header, checked with its own lookup), where the H3 has 17 by 9; the text below describes the H3 layout. Expected engine speed for the cold start emission monitor (fault code P1400: the check that the engine really runs the fast idle and spark timing used to warm the catalytic converter after a cold start), by time since start (rows, 0 to 42.5 s) and coolant temperature (columns), with the transmission in gear. The monitor compares this with the actual engine speed while the vehicle is stopped with the throttle closed. O...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (ECT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>s (run time)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5.3" />
      <LABEL index="2" value="10.6" />
      <LABEL index="3" value="15.9" />
      <LABEL index="4" value="21.2" />
      <LABEL index="5" value="26.5" />
      <LABEL index="6" value="31.8" />
      <LABEL index="7" value="37.1" />
      <LABEL index="8" value="42.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3495E" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x78B" flags="0x30">
    <title>Cold Start Emission Monitor - Expected Idle Speed, Park / Neutral (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this table has 9 rows and 17 columns on this operating system (from its own table header, checked with its own lookup), where the H3 has 17 by 9; the text below describes the H3 layout. Expected engine speed for the cold start emission monitor (fault code P1400: the check that the engine really runs the fast idle and spark timing used to warm the catalytic converter after a cold start), by time since start (rows, 0 to 42.5 s) and coolant temperature (columns), with the transmission in Park or Neutral. The monitor compares this with the actual engine speed while the vehicle is stopped with the throttl...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (ECT)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-28" />
      <LABEL index="2" value="-16" />
      <LABEL index="3" value="-4" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="20" />
      <LABEL index="6" value="32" />
      <LABEL index="7" value="44" />
      <LABEL index="8" value="56" />
      <LABEL index="9" value="68" />
      <LABEL index="10" value="80" />
      <LABEL index="11" value="92" />
      <LABEL index="12" value="104" />
      <LABEL index="13" value="116" />
      <LABEL index="14" value="128" />
      <LABEL index="15" value="140" />
      <LABEL index="16" value="152" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>s (run time)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="5.3" />
      <LABEL index="2" value="10.6" />
      <LABEL index="3" value="15.9" />
      <LABEL index="4" value="21.2" />
      <LABEL index="5" value="26.5" />
      <LABEL index="6" value="31.8" />
      <LABEL index="7" value="37.1" />
      <LABEL index="8" value="42.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34A96" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>rpm</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x78C" flags="0x30">
    <title>Cold Start Emission Monitor - Expected Spark vs Airmass x RPM (dormant)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this table has 17 rows and 9 columns on this operating system (from its own table header, checked with its own lookup), where the H3 has 9 by 17; the text below describes the H3 layout. Expected spark advance for the cold start emission monitor (fault code P1400), by cylinder airmass (rows) and engine speed (columns), used in every spark mode except the one that has its own pair of expected spark tables. The value is multiplied by four factor curves (run time, start-up coolant, coolant and throttle) and the monitor compares the result with the actual spark advance. On this calibration the monitor is...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x34DBE" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x78D" flags="0x30">
    <title>Maximum Knock Retard vs. RPM vs. MAP</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this table has 17 rows and 17 columns on this operating system (from its own table header, checked with its own lookup), where the H3 has 9 by 17; the text below describes the H3 layout. Located on the H3 by code homology with the Cobalt; scale carried from the Cobalt. Evidence: ledger:E0148, ledger:E0166, ledger:E0196, ledger:E0213, ledger:E0234, ledger:E0257, ledger:E0260, ledger:E1297, ledger:E1795</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="20" />
      <LABEL index="1" value="31.3" />
      <LABEL index="2" value="42.6" />
      <LABEL index="3" value="53.9" />
      <LABEL index="4" value="65.2" />
      <LABEL index="5" value="76.5" />
      <LABEL index="6" value="87.8" />
      <LABEL index="7" value="99.1" />
      <LABEL index="8" value="110.4" />
      <LABEL index="9" value="121.7" />
      <LABEL index="10" value="133" />
      <LABEL index="11" value="144.3" />
      <LABEL index="12" value="155.6" />
      <LABEL index="13" value="166.9" />
      <LABEL index="14" value="178.2" />
      <LABEL index="15" value="189.5" />
      <LABEL index="16" value="200.8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2B723" mmedelementsizebits="8" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x78E" flags="0x30">
    <title>Misfire - Catalyst Damage Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this table has 17 rows and 8 columns on this operating system (from its own table header, checked with its own lookup), where the H3 has 11 by 8; the text below describes the H3 layout. Misfire monitor: misfire rate (misfires per 100 cylinder firings, measured over 200 engine revolutions) at or above which the window counts as catalyst damaging. Looked up at the engine speed and load of the start and of the end of the window; the larger limit is used. Stock 18 % at low speed and load falling to 5 % at high speed or load. Effect: raise = more misfire is tolerated before the catalyst-damage decision and the flas...</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>8</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1000" />
      <LABEL index="2" value="2000" />
      <LABEL index="3" value="3000" />
      <LABEL index="4" value="4000" />
      <LABEL index="5" value="5000" />
      <LABEL index="6" value="6000" />
      <LABEL index="7" value="7000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>% load</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <LABEL index="11" value="110" />
      <LABEL index="12" value="120" />
      <LABEL index="13" value="130" />
      <LABEL index="14" value="140" />
      <LABEL index="15" value="150" />
      <LABEL index="16" value="160" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3934A" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="8" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>%</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x78F" flags="0x30">
    <title>Torque MAP correction vs RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this table has 17 rows and 17 columns on this operating system (from its own table header, checked with its own lookup), where the H3 has 17 by 9; the text below describes the H3 layout. Multiplier on gross torque vs rpm and MAP; stock all 1.0. Torque model - DO NOT TUNE until the live PID 1A2D replay matches (E0246) The model as a whole reproduces logged delivered torque (PID 1A2D) at steady load within about 6 % (correlation 0.98, E0280); still reference-only. Effect: engine torque estimate used by shift pressure, torque reduction, TCC and ETC torque control Evidence: ledger:E0246, ledger:E0280, ledger:E1314...</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="20" />
      <LABEL index="1" value="31.3" />
      <LABEL index="2" value="42.6" />
      <LABEL index="3" value="53.9" />
      <LABEL index="4" value="65.2" />
      <LABEL index="5" value="76.5" />
      <LABEL index="6" value="87.8" />
      <LABEL index="7" value="99.1" />
      <LABEL index="8" value="110.4" />
      <LABEL index="9" value="121.7" />
      <LABEL index="10" value="133" />
      <LABEL index="11" value="144.3" />
      <LABEL index="12" value="155.6" />
      <LABEL index="13" value="166.9" />
      <LABEL index="14" value="178.2" />
      <LABEL index="15" value="189.5" />
      <LABEL index="16" value="200.8" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x30CDC" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x790" flags="0x0">
    <title>Extra Diagnostic Service Gate Enable (inactive)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Enables or disables an additional diagnostic-service gate that must pass an engine speed threshold and two other status checks before a periodic diagnostic service routine runs. Stock is off on this vehicle; the same gate is on in some other GM applications of this controller. Effect: Turning it on allows the diagnostic routine to run once the speed and status conditions are met; off, the routine never runs. Stock is off. Evidence: ledger:E0620, ledger:E0799, ledger:E0805, ledger:E1795</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x39A86" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>flag</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x791" flags="0x0">
    <title>MAP Sensor Circuit High Check Enable (P0108 / P1106)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the MAP sensor circuit high check on or off. 1: the PCM runs the check and can set P0108 and P1106. 0: the check never runs. Stock 1 (on). Effect: 0 = MAP circuit high check off; 1 = on (stock) Evidence: ledger:E1769, ledger:E1795</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x389F8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x792" flags="0x0">
    <title>MAP Sensor Circuit Low Check Enable (P0107 / P1107)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the MAP sensor circuit low check on or off. 1: the PCM runs the check and can set P0107 and P1107. 0: the check never runs. Stock 1 (on). Effect: 0 = MAP circuit low check off; 1 = on (stock) Evidence: ledger:E1769, ledger:E1795</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x389FA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x793" flags="0x0">
    <title>Spark - Medium Resolution Calculation Maximum RPM</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this item is active on this operating system: the code that reads it runs with this calibration&#x27;s settings (checked by running this operating system&#x27;s code), so the dormancy described below for the H3 does not apply here. Engine speed below which the spark code uses its modified medium resolution calculation; it runs only above the minimum RPM and below this maximum. Stock 0 with the minimum at 8000 rpm, so it never runs on the stock calibration (dormant). Effect: leave at stock Evidence: ledger:E0436, ledger:E1769, ledger:E1795</description>
    <CATEGORYMEM index="0" category="1" />
    <EMBEDDEDDATA mmedaddress="0x2CFA4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x794" flags="0x30">
    <title>Commanded Mixture Lean Offset vs Temperature C</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this curve holds non-zero values in this calibration, so the H3 remark that it is inactive (all zero there) does not apply here. Same commanded-mixture lean-offset mechanism as the other selectable variants of this table (a temperature-indexed amount subtracted from the commanded air-fuel mixture, floored so the mixture is never commanded leaner than a 1:1 equivalence ratio): this is variant C, selected instead of the others under a different vehicle condition. Its own calibration is entirely zero at every modelled-temperature point on this vehicle, so selecting it never actually changes the commanded mixture...</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26F4E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ ratio offset</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x795" flags="0x30">
    <title>Commanded Mixture Lean Offset vs Temperature D</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. On OS 12610624: this curve holds non-zero values in this calibration, so the H3 remark that it is inactive (all zero there) does not apply here. Same commanded-mixture lean-offset mechanism as the other selectable variants of this table (a temperature-indexed amount subtracted from the commanded air-fuel mixture, floored so the mixture is never commanded leaner than a 1:1 equivalence ratio): this is variant D, selected instead of the others under a different vehicle condition. Its own calibration is entirely zero at every modelled-temperature point on this vehicle, so selecting it never actually changes the commanded mixture...</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26F96" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ ratio offset</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x796" flags="0x30">
    <title>Commanded Mixture Lean Offset vs Temperature A</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded air-fuel mixture is pulled leaner as the engine warms: this curve sets how much richness is subtracted from the commanded mixture at each modelled engine temperature, from a small offset near -40 C (0.10 equivalence ratio) up to a large offset by 216 C (0.90), floored so the mixture is never commanded leaner than a 1:1 equivalence ratio. One of two selectable variants; this is variant A. 1x33 curve, -40 to 216 C in 8-degree steps. Effect: raise = more richness subtracted at that temperature (mixture commanded leaner, down to the 1:1 floor) Evidence: ledger:E0711, ledger:E1800</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26FDE" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ ratio offset</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x797" flags="0x30">
    <title>Commanded Mixture Lean Offset vs Temperature B</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Commanded air-fuel mixture is pulled leaner as the engine warms: this curve sets how much richness is subtracted from the commanded mixture at each modelled engine temperature, from a small offset near -40 C (0.10 equivalence ratio) up to a large offset by 216 C (0.90), floored so the mixture is never commanded leaner than a 1:1 equivalence ratio. One of two selectable variants; this is variant B (identical stock data to variant A). 1x33 curve, -40 to 216 C in 8-degree steps. Effect: raise = more richness subtracted at that temperature (mixture commanded leaner, down to the 1:1 floor) Evidence: ledger:E0711, ledger:E1800</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x27026" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ ratio offset</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x798" flags="0x30">
    <title>PE/COT Spark Advance Correction vs RPM vs EQ</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Spark added while Power Enrichment / catalyst over-temp enrichment is active, vs rpm and commanded EQ. Stock H3 0..5 deg (E0185) Effect: more = more timing when rich Evidence: ledger:E0185, ledger:E0210, ledger:E0213, ledger:E0260, ledger:E1297, ledger:E1836</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="800" />
      <LABEL index="1" value="1600" />
      <LABEL index="2" value="2400" />
      <LABEL index="3" value="3200" />
      <LABEL index="4" value="4000" />
      <LABEL index="5" value="4800" />
      <LABEL index="6" value="5600" />
      <LABEL index="7" value="6400" />
      <LABEL index="8" value="7200" />
      <LABEL index="9" value="8000" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>11</indexcount>
      <units>EQ ratio</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="1.00" />
      <LABEL index="1" value="1.05" />
      <LABEL index="2" value="1.10" />
      <LABEL index="3" value="1.15" />
      <LABEL index="4" value="1.20" />
      <LABEL index="5" value="1.25" />
      <LABEL index="6" value="1.30" />
      <LABEL index="7" value="1.35" />
      <LABEL index="8" value="1.40" />
      <LABEL index="9" value="1.45" />
      <LABEL index="10" value="1.50" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E01D" mmedelementsizebits="8" mmedrowcount="11" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X*0.5"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x799" flags="0x30">
    <title>Idle Airflow - Alternator Load Adder vs RPM - Park/Neutral</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Idle airflow added vs rpm (columns) and alternator field duty (rows, 0-100 %), Park/Neutral. Stock 0 at the first row rising to 1.18 g/s at the last row from 512 rpm up. Effect: raise = more idle air when that load is present Evidence: ledger:E0286, ledger:E0287, ledger:E0294, ledger:E1836</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>5</indexcount>
      <units>% alternator field duty</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="25" />
      <LABEL index="2" value="50" />
      <LABEL index="3" value="75" />
      <LABEL index="4" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2A776" mmedelementsizebits="16" mmedrowcount="5" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x79A" flags="0x30">
    <title>Catalyst Temp Model - Start-Up Pull Toward Intake Air</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. At start-up the modelled catalyst temperature is moved this share of the way from its last value toward the intake air temperature, by how long the engine was off (0 to 18.2 h). Stock 1.6 % right after shut-off, rising to 7.0 % after 18 h. Effect: raise = the modelled catalyst temperature starts closer to intake air temperature after a stop Evidence: ledger:E0363, ledger:E0936, ledger:E1186, ledger:E1836</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>h (engine-off time)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1.138" />
      <LABEL index="2" value="2.276" />
      <LABEL index="3" value="3.413" />
      <LABEL index="4" value="4.551" />
      <LABEL index="5" value="5.689" />
      <LABEL index="6" value="6.827" />
      <LABEL index="7" value="7.964" />
      <LABEL index="8" value="9.102" />
      <LABEL index="9" value="10.24" />
      <LABEL index="10" value="11.378" />
      <LABEL index="11" value="12.516" />
      <LABEL index="12" value="13.653" />
      <LABEL index="13" value="14.791" />
      <LABEL index="14" value="15.929" />
      <LABEL index="15" value="17.067" />
      <LABEL index="16" value="18.204" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2187A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% of gap closed</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>99.998474</max>
      <MATH equation="X/655.36"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x79B" flags="0x30">
    <title>Pedal Throttle Request Factor vs Commanded Air-Fuel Ratio</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Factor on the driver&#x27;s pedal throttle request, by the commanded air-fuel ratio (0 to 32). The PCM multiplies the pedal map&#x27;s throttle request by this and several other factors. 1.0 = no change; lower = less throttle for the same pedal. Stock 1.0 everywhere. Effect: lower = less throttle for the same pedal position Evidence: ledger:E0594, ledger:E0947, ledger:E1836</description>
    <CATEGORYMEM index="0" category="8" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>AFR (commanded)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="2" />
      <LABEL index="2" value="4" />
      <LABEL index="3" value="6" />
      <LABEL index="4" value="8" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="12" />
      <LABEL index="7" value="14" />
      <LABEL index="8" value="16" />
      <LABEL index="9" value="18" />
      <LABEL index="10" value="20" />
      <LABEL index="11" value="22" />
      <LABEL index="12" value="24" />
      <LABEL index="13" value="26" />
      <LABEL index="14" value="28" />
      <LABEL index="15" value="30" />
      <LABEL index="16" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x231AC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x79C" flags="0x30">
    <title>Cruise Control - Throttle Area vs Cruise Demand</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Throttle opening above the idle throttle area that the cruise control asks for, by the controller&#x27;s internal demand (a lower demand means more throttle). Multiplied by a barometric correction and ramped, it is used in place of the accelerator pedal while cruise holds speed. Stock 100 % at the lowest demand falling to 0 from the middle of the range. Effect: raise = more throttle for the same cruise demand Evidence: ledger:E0943, ledger:E1326, ledger:E1836</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>cruise demand (internal counts)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-5760" />
      <LABEL index="1" value="-5272" />
      <LABEL index="2" value="-4784" />
      <LABEL index="3" value="-4296" />
      <LABEL index="4" value="-3808" />
      <LABEL index="5" value="-3320" />
      <LABEL index="6" value="-2832" />
      <LABEL index="7" value="-2344" />
      <LABEL index="8" value="-1856" />
      <LABEL index="9" value="-1368" />
      <LABEL index="10" value="-880" />
      <LABEL index="11" value="-392" />
      <LABEL index="12" value="96" />
      <LABEL index="13" value="584" />
      <LABEL index="14" value="1072" />
      <LABEL index="15" value="1560" />
      <LABEL index="16" value="2048" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21FA2" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>% throttle area</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>100.000000</max>
      <MATH equation="X/655.35"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x79D" flags="0x0">
    <title>PCM EEPROM Check Enable (P062F)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the PCM EEPROM check on or off. 1: the PCM runs the check and can set P062F. 0: the check never runs, so P062F is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P062F check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725, ledger:E1869</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A20" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x79E" flags="0x0">
    <title>PCM Keep Alive Memory Check Enable (P0603)</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Turns the PCM keep alive memory check on or off. 1: the PCM runs the check and can set P0603. 0: the check never runs, so P0603 is never set and never reported as passed. Stock 1 (on). Use 0 only when the part this check watches is not fitted (for example on an engine swap). Effect: 0 = P0603 check off (never set); 1 = check on Evidence: ledger:E0434, ledger:E1725, ledger:E1869</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38A22" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>1 = check on, 0 = off</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x79F" flags="0x0">
    <title>MAP Circuit High - Throttle Area Below Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit high monitor (P0108, and P1106 for intermittent faults): with the engine running past its arming time, above the engine speed limit at any throttle, or at or below it under the throttle area limit, each MAP sensor reading above the high reading threshold counts as a high sample. The threshold is in raw sensor counts, so it does not follow the MAP sensor gain and offset: on the stock sensor it is about 102.6 kPa, and boost read by the stock sensor sets P0108. This is the throttle area below which the test runs at or below the engine speed limit. Stock 58 %. Effect: lower = the low-speed test stops at a small...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38864" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>399.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A0" flags="0x0">
    <title>MAP Circuit High - Engine Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit high monitor (P0108, and P1106 for intermittent faults): with the engine running past its arming time, above the engine speed limit at any throttle, or at or below it under the throttle area limit, each MAP sensor reading above the high reading threshold counts as a high sample. The threshold is in raw sensor counts, so it does not follow the MAP sensor gain and offset: on the stock sensor it is about 102.6 kPa, and boost read by the stock sensor sets P0108. This is the engine speed limit. Stock 1100 rpm. Effect: raise = the throttle-limited low-speed test covers a higher engine speed Evidence: ledger:E0434...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x386FC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A1" flags="0x0">
    <title>MAP Circuit High - High Reading Threshold</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit high monitor (P0108, and P1106 for intermittent faults): with the engine running past its arming time, above the engine speed limit at any throttle, or at or below it under the throttle area limit, each MAP sensor reading above the high reading threshold counts as a high sample. The threshold is in raw sensor counts, so it does not follow the MAP sensor gain and offset: on the stock sensor it is about 102.6 kPa, and boost read by the stock sensor sets P0108. This is the high reading threshold in raw sensor counts (65535 = full scale). Stock 32113, about 102.6 kPa on the stock sensor. With a different s...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38860" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>A/D counts</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A2" flags="0x0">
    <title>MAP Circuit Low - Throttle Area Below Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit low monitor (P0107, and P1107 for intermittent faults): with the ignition on, at or below the engine speed limit, or above it with throttle area at or above the area limit, each MAP sensor reading below the low voltage threshold counts as a low sample. The raw reading does not depend on the MAP sensor gain and offset. This is the throttle area at or above which the test runs at or below the engine speed limit. Stock 0 % (any). Effect: raise = the low-speed test needs some throttle Evidence: ledger:E0434, ledger:E0887, ledger:E1869</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x3885C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>% throttle area</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>399.993896</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/163.84"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A3" flags="0x0">
    <title>MAP Circuit Low - Engine Speed Limit</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit low monitor (P0107, and P1107 for intermittent faults): with the ignition on, at or below the engine speed limit, or above it with throttle area at or above the area limit, each MAP sensor reading below the low voltage threshold counts as a low sample. The raw reading does not depend on the MAP sensor gain and offset. This is the engine speed limit. Stock 1100 rpm. Effect: raise = the low-throttle test runs up to a higher engine speed Evidence: ledger:E0434, ledger:E0887, ledger:E1869</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38706" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A4" flags="0x0">
    <title>MAP Circuit Low - P0107 Fail Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit low monitor (P0107, and P1107 for intermittent faults): with the ignition on, at or below the engine speed limit, or above it with throttle area at or above the area limit, each MAP sensor reading below the low voltage threshold counts as a low sample. The raw reading does not depend on the MAP sensor gain and offset. For P0107 this is the number of low samples that sets the code. Stock 320. Effect: raise = more low samples needed to set P0107 Evidence: ledger:E0434, ledger:E0887, ledger:E1869</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38702" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A5" flags="0x0">
    <title>MAP Circuit Low - P0107 Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit low monitor (P0107, and P1107 for intermittent faults): with the ignition on, at or below the engine speed limit, or above it with throttle area at or above the area limit, each MAP sensor reading below the low voltage threshold counts as a low sample. The raw reading does not depend on the MAP sensor gain and offset. For P0107 this is the number of samples after which the test passes. Stock 400. Effect: raise = longer P0107 window (keep above the fail count) Evidence: ledger:E0434, ledger:E0887, ledger:E1869</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38704" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A6" flags="0x0">
    <title>MAP Circuit High - P0108 Fail Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit high monitor (P0108, and P1106 for intermittent faults): with the engine running past its arming time, above the engine speed limit at any throttle, or at or below it under the throttle area limit, each MAP sensor reading above the high reading threshold counts as a high sample. The threshold is in raw sensor counts, so it does not follow the MAP sensor gain and offset: on the stock sensor it is about 102.6 kPa, and boost read by the stock sensor sets P0108. For P0108 this is the number of high samples that sets the code. Stock 320. Effect: raise = more high samples needed to set P0108 Evidence: ledger:E043...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x386F8" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A7" flags="0x0">
    <title>MAP Circuit High - P0108 Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit high monitor (P0108, and P1106 for intermittent faults): with the engine running past its arming time, above the engine speed limit at any throttle, or at or below it under the throttle area limit, each MAP sensor reading above the high reading threshold counts as a high sample. The threshold is in raw sensor counts, so it does not follow the MAP sensor gain and offset: on the stock sensor it is about 102.6 kPa, and boost read by the stock sensor sets P0108. For P0108 this is the number of samples after which the test passes. Stock 400. Effect: raise = longer P0108 window (keep above the fail count) Evidenc...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x386FA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A8" flags="0x0">
    <title>MAP Circuit High - P1106 Fail Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit high monitor (P0108, and P1106 for intermittent faults): with the engine running past its arming time, above the engine speed limit at any throttle, or at or below it under the throttle area limit, each MAP sensor reading above the high reading threshold counts as a high sample. The threshold is in raw sensor counts, so it does not follow the MAP sensor gain and offset: on the stock sensor it is about 102.6 kPa, and boost read by the stock sensor sets P0108. For P1106 this is the number of high samples that fails the long window. Stock 640. Effect: raise = more high samples needed to set P1106 Evidence: led...</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x386F4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7A9" flags="0x0">
    <title>MAP Circuit High - P1106 Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit high monitor (P0108, and P1106 for intermittent faults): with the engine running past its arming time, above the engine speed limit at any throttle, or at or below it under the throttle area limit, each MAP sensor reading above the high reading threshold counts as a high sample. The threshold is in raw sensor counts, so it does not follow the MAP sensor gain and offset: on the stock sensor it is about 102.6 kPa, and boost read by the stock sensor sets P0108. For P1106 this is the length of the long window. Stock 6400. Effect: raise = longer P1106 window Evidence: ledger:E0434, ledger:E0889, ledger:E1869</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x386F6" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7AA" flags="0x0">
    <title>MAP Circuit Low - P1107 Fail Count</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit low monitor (P0107, and P1107 for intermittent faults): with the ignition on, at or below the engine speed limit, or above it with throttle area at or above the area limit, each MAP sensor reading below the low voltage threshold counts as a low sample. The raw reading does not depend on the MAP sensor gain and offset. For P1107 this is the number of low samples that fails the long window. Stock 640. Effect: raise = more low samples needed to set P1107 Evidence: ledger:E0434, ledger:E0887, ledger:E1869</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x386FE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7AB" flags="0x0">
    <title>MAP Circuit Low - P1107 Window Samples</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. MAP sensor circuit low monitor (P0107, and P1107 for intermittent faults): with the ignition on, at or below the engine speed limit, or above it with throttle area at or above the area limit, each MAP sensor reading below the low voltage threshold counts as a low sample. The raw reading does not depend on the MAP sensor gain and offset. For P1107 this is the length of the long window. Stock 6400. Effect: raise = longer P1107 window Evidence: ledger:E0434, ledger:E0887, ledger:E1869</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x38700" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7AC" flags="0x0">
    <title>P0462 Fail - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0462 (fuel level sensor circuit low) sets once the sender has read below its low threshold for this long without returning to the normal range. Stock 60 s. Effect: raise = P0462 takes longer to set Evidence: ledger:E0909, ledger:E0957, ledger:E1869</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2034C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7AD" flags="0x0">
    <title>P0463 Fail - Time</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. P0463 (fuel level sensor circuit high) sets once the sender has read above its high threshold for this long without returning to the normal range. Stock 60 s. Effect: raise = P0463 takes longer to set Evidence: ledger:E0957, ledger:E1869</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x2034A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>3276.750000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/20"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7AE" flags="0x0">
    <title>ETC Torque Control - Window, Airmass Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest cylinder airmass (stock 1.0 g/cyl). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335, ledger:E1900</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20FCE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/cyl</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8.191875</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7AF" flags="0x0">
    <title>ETC Torque Control - Window, Airmass Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest cylinder airmass (stock 0.02 g/cyl). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335, ledger:E1900</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20FD0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>g/cyl</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8.191875</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8000"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B0" flags="0x0">
    <title>ETC Torque Control - Window, Coolant Temperature Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest coolant temperature (stock 30 C). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335, ledger:E1900</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20FDA" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>-256.000000</min>
    <max>255.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B1" flags="0x0">
    <title>ETC Torque Control - Window, Engine Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest filtered engine speed (stock 7000 rpm). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335, ledger:E1900</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20FD2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B2" flags="0x0">
    <title>ETC Torque Control - Window, Engine Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest filtered engine speed (stock 400 rpm). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335, ledger:E1900</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20FD4" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B3" flags="0x0">
    <title>ETC Torque Control - Window, Run Time Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine run time since start needed (stock 0 s). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335, ledger:E1900</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20FDC" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B4" flags="0x0">
    <title>ETC Torque Control - Window, Vehicle Speed Maximum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Highest vehicle speed (stock 512 km/h: no limit). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335, ledger:E1900</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20FDE" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B5" flags="0x0">
    <title>ETC Torque Control - Window, Vehicle Speed Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Lowest vehicle speed (stock 1 km/h). Part of the window the ETC torque controller needs before it may run. Inactive on the 2006 H3. Whether it is active on this operating system has not been determined. Effect: no effect on the stock calibration Evidence: ledger:E0341, ledger:E1335, ledger:E1900</description>
    <CATEGORYMEM index="0" category="8" />
    <EMBEDDEDDATA mmedaddress="0x20FE0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>km/h</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>511.992188</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/128"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B6" flags="0x0">
    <title>Oil Life Reset - Time Window</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Engine oil life reset with the accelerator (key on, engine not turning): time from the first press in which all presses must be made; after it the count starts again. Stock 5 s. Effect: raise = more time to complete the presses Evidence: ledger:E1128, ledger:E1900</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x2CF90" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>s</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>409.593750</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/160"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B7" flags="0x0">
    <title>Per-Cylinder Learn Table RPM Enable Minimum</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Per-cylinder learn: the per-cylinder learn and blend block runs only while engine speed is at or above this. Stock 420 rpm. Effect: raise = the per-cylinder learn needs a higher engine speed before it runs Evidence: ledger:E0775, ledger:E1259, ledger:E1900</description>
    <CATEGORYMEM index="0" category="7" />
    <EMBEDDEDDATA mmedaddress="0x22D00" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B8" flags="0x0">
    <title>Service Throttle Test - Minimum MAP</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Below this manifold pressure the scan tool throttle test is refused. Stock 20 kPa. Used only while the scan tool throttle test runs. Effect: safety interlock Evidence: ledger:E0775, ledger:E1796, ledger:E1900</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x24180" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>kPa</units>
    <decimalpl>3</decimalpl>
    <min>0.000000</min>
    <max>255.996094</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/256"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7B9" flags="0x0">
    <title>Service Throttle Test - Maximum Engine Speed</title>
    <description>Change in small steps and log. Located and checked in this OS&#x27;s code (OS 12610624), not confirmed on a vehicle. The routine that reads this item is the same code as on the 2006 Hummer H3 (OS 12627884). Text and quoted stock values describe the H3; this calibration&#x27;s values may differ. Above this engine speed the scan tool throttle test is refused. Stock 270 rpm. Used only while the scan tool throttle test runs. Effect: safety interlock Evidence: ledger:E0775, ledger:E1796, ledger:E1900</description>
    <CATEGORYMEM index="0" category="11" />
    <EMBEDDEDDATA mmedaddress="0x2417C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x7BA" flags="0x30">
    <title>Injector Offset vs Battery Voltage vs MAP</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Injector offset (dead time) in ms by battery voltage (rows) and manifold pressure (columns, 20 to 200 kPa). Same role as the vacuum based offset table; this one is used when Injector Offset Table Select is not 0. Effect: raise = longer injector pulse at that voltage and pressure (richer) Evidence: ledger:E1587</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>kPa (manifold pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="20" />
      <LABEL index="1" value="25.625" />
      <LABEL index="2" value="31.25" />
      <LABEL index="3" value="36.875" />
      <LABEL index="4" value="42.5" />
      <LABEL index="5" value="48.125" />
      <LABEL index="6" value="53.75" />
      <LABEL index="7" value="59.375" />
      <LABEL index="8" value="65" />
      <LABEL index="9" value="70.625" />
      <LABEL index="10" value="76.25" />
      <LABEL index="11" value="81.875" />
      <LABEL index="12" value="87.5" />
      <LABEL index="13" value="93.125" />
      <LABEL index="14" value="98.75" />
      <LABEL index="15" value="104.375" />
      <LABEL index="16" value="110" />
      <LABEL index="17" value="115.625" />
      <LABEL index="18" value="121.25" />
      <LABEL index="19" value="126.875" />
      <LABEL index="20" value="132.5" />
      <LABEL index="21" value="138.125" />
      <LABEL index="22" value="143.75" />
      <LABEL index="23" value="149.375" />
      <LABEL index="24" value="155" />
      <LABEL index="25" value="160.625" />
      <LABEL index="26" value="166.25" />
      <LABEL index="27" value="171.875" />
      <LABEL index="28" value="177.5" />
      <LABEL index="29" value="183.125" />
      <LABEL index="30" value="188.75" />
      <LABEL index="31" value="194.375" />
      <LABEL index="32" value="200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>V (battery)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="4.5" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="5.5" />
      <LABEL index="3" value="6" />
      <LABEL index="4" value="6.5" />
      <LABEL index="5" value="7" />
      <LABEL index="6" value="7.5" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="8.5" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="9.5" />
      <LABEL index="11" value="10" />
      <LABEL index="12" value="10.5" />
      <LABEL index="13" value="11" />
      <LABEL index="14" value="11.5" />
      <LABEL index="15" value="12" />
      <LABEL index="16" value="12.5" />
      <LABEL index="17" value="13" />
      <LABEL index="18" value="13.5" />
      <LABEL index="19" value="14" />
      <LABEL index="20" value="14.5" />
      <LABEL index="21" value="15" />
      <LABEL index="22" value="15.5" />
      <LABEL index="23" value="16" />
      <LABEL index="24" value="16.5" />
      <LABEL index="25" value="17" />
      <LABEL index="26" value="17.5" />
      <LABEL index="27" value="18" />
      <LABEL index="28" value="18.5" />
      <LABEL index="29" value="19" />
      <LABEL index="30" value="19.5" />
      <LABEL index="31" value="20" />
      <LABEL index="32" value="20.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25C9A" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ms</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x7BB" flags="0x0">
    <title>Injector Offset Table Select</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Chooses the injector offset table: 0 = the table by battery voltage and vacuum, any other value = the table by battery voltage and manifold pressure. Effect: changes which injector offset table is used Evidence: ledger:E1587</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x25406" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>selector</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x7BC" flags="0x30">
    <title>Open Loop EQ Multiplier vs MAP vs RPM</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Multiplier on the open loop commanded fuel/air ratio (EQ), by engine speed (rows) and manifold pressure (columns, 20 to 200 kPa). The base open loop EQ table is multiplied by this, then by the open loop airflow gain. 1.0 = no change. Effect: raise = richer open loop fuelling at that speed and pressure Evidence: ledger:E1587</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>kPa (manifold pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="20" />
      <LABEL index="1" value="25.625" />
      <LABEL index="2" value="31.25" />
      <LABEL index="3" value="36.875" />
      <LABEL index="4" value="42.5" />
      <LABEL index="5" value="48.125" />
      <LABEL index="6" value="53.75" />
      <LABEL index="7" value="59.375" />
      <LABEL index="8" value="65" />
      <LABEL index="9" value="70.625" />
      <LABEL index="10" value="76.25" />
      <LABEL index="11" value="81.875" />
      <LABEL index="12" value="87.5" />
      <LABEL index="13" value="93.125" />
      <LABEL index="14" value="98.75" />
      <LABEL index="15" value="104.375" />
      <LABEL index="16" value="110" />
      <LABEL index="17" value="115.625" />
      <LABEL index="18" value="121.25" />
      <LABEL index="19" value="126.875" />
      <LABEL index="20" value="132.5" />
      <LABEL index="21" value="138.125" />
      <LABEL index="22" value="143.75" />
      <LABEL index="23" value="149.375" />
      <LABEL index="24" value="155" />
      <LABEL index="25" value="160.625" />
      <LABEL index="26" value="166.25" />
      <LABEL index="27" value="171.875" />
      <LABEL index="28" value="177.5" />
      <LABEL index="29" value="183.125" />
      <LABEL index="30" value="188.75" />
      <LABEL index="31" value="194.375" />
      <LABEL index="32" value="200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="400" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1200" />
      <LABEL index="4" value="1600" />
      <LABEL index="5" value="2000" />
      <LABEL index="6" value="2400" />
      <LABEL index="7" value="2800" />
      <LABEL index="8" value="3200" />
      <LABEL index="9" value="3600" />
      <LABEL index="10" value="4000" />
      <LABEL index="11" value="4400" />
      <LABEL index="12" value="4800" />
      <LABEL index="13" value="5200" />
      <LABEL index="14" value="5600" />
      <LABEL index="15" value="6000" />
      <LABEL index="16" value="6400" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x27278" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7BD" flags="0x30">
    <title>Open Loop Airflow Gain vs Temperature vs MAP</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Multiplier on the open loop fuel/air ratio after the speed and pressure multiplier, by manifold pressure (rows, 20 to 200 kPa) and modelled intake temperature (columns, -40 to 216 C). 1.0 = no change. Effect: raise = richer open loop fuelling at that pressure and temperature Evidence: ledger:E1587</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>degC (modelled intake temperature)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-32" />
      <LABEL index="2" value="-24" />
      <LABEL index="3" value="-16" />
      <LABEL index="4" value="-8" />
      <LABEL index="5" value="0" />
      <LABEL index="6" value="8" />
      <LABEL index="7" value="16" />
      <LABEL index="8" value="24" />
      <LABEL index="9" value="32" />
      <LABEL index="10" value="40" />
      <LABEL index="11" value="48" />
      <LABEL index="12" value="56" />
      <LABEL index="13" value="64" />
      <LABEL index="14" value="72" />
      <LABEL index="15" value="80" />
      <LABEL index="16" value="88" />
      <LABEL index="17" value="96" />
      <LABEL index="18" value="104" />
      <LABEL index="19" value="112" />
      <LABEL index="20" value="120" />
      <LABEL index="21" value="128" />
      <LABEL index="22" value="136" />
      <LABEL index="23" value="144" />
      <LABEL index="24" value="152" />
      <LABEL index="25" value="160" />
      <LABEL index="26" value="168" />
      <LABEL index="27" value="176" />
      <LABEL index="28" value="184" />
      <LABEL index="29" value="192" />
      <LABEL index="30" value="200" />
      <LABEL index="31" value="208" />
      <LABEL index="32" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>kPa (manifold pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="20" />
      <LABEL index="1" value="25.625" />
      <LABEL index="2" value="31.25" />
      <LABEL index="3" value="36.875" />
      <LABEL index="4" value="42.5" />
      <LABEL index="5" value="48.125" />
      <LABEL index="6" value="53.75" />
      <LABEL index="7" value="59.375" />
      <LABEL index="8" value="65" />
      <LABEL index="9" value="70.625" />
      <LABEL index="10" value="76.25" />
      <LABEL index="11" value="81.875" />
      <LABEL index="12" value="87.5" />
      <LABEL index="13" value="93.125" />
      <LABEL index="14" value="98.75" />
      <LABEL index="15" value="104.375" />
      <LABEL index="16" value="110" />
      <LABEL index="17" value="115.625" />
      <LABEL index="18" value="121.25" />
      <LABEL index="19" value="126.875" />
      <LABEL index="20" value="132.5" />
      <LABEL index="21" value="138.125" />
      <LABEL index="22" value="143.75" />
      <LABEL index="23" value="149.375" />
      <LABEL index="24" value="155" />
      <LABEL index="25" value="160.625" />
      <LABEL index="26" value="166.25" />
      <LABEL index="27" value="171.875" />
      <LABEL index="28" value="177.5" />
      <LABEL index="29" value="183.125" />
      <LABEL index="30" value="188.75" />
      <LABEL index="31" value="194.375" />
      <LABEL index="32" value="200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x28418" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7BE" flags="0x30">
    <title>Transient Fuel - Wall Deposit Fraction vs MAP vs Temp</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Transient fuel: fraction of each injection that sticks to the intake port wall instead of entering the cylinder, by manifold pressure (rows, 20 to 200 kPa) and port temperature (columns). The engine adds fuel to make up for it on tip-in and removes it on tip-out. Effect: raise = more tip-in fuel and more tip-out fuel removal Evidence: ledger:E1587</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (modelled port temperature)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-24" />
      <LABEL index="2" value="-8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="24" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="56" />
      <LABEL index="7" value="72" />
      <LABEL index="8" value="88" />
      <LABEL index="9" value="104" />
      <LABEL index="10" value="120" />
      <LABEL index="11" value="136" />
      <LABEL index="12" value="152" />
      <LABEL index="13" value="168" />
      <LABEL index="14" value="184" />
      <LABEL index="15" value="200" />
      <LABEL index="16" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>kPa (manifold pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="20" />
      <LABEL index="1" value="31.25" />
      <LABEL index="2" value="42.5" />
      <LABEL index="3" value="53.75" />
      <LABEL index="4" value="65" />
      <LABEL index="5" value="76.25" />
      <LABEL index="6" value="87.5" />
      <LABEL index="7" value="98.75" />
      <LABEL index="8" value="110" />
      <LABEL index="9" value="121.25" />
      <LABEL index="10" value="132.5" />
      <LABEL index="11" value="143.75" />
      <LABEL index="12" value="155" />
      <LABEL index="13" value="166.25" />
      <LABEL index="14" value="177.5" />
      <LABEL index="15" value="188.75" />
      <LABEL index="16" value="200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2669C" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7BF" flags="0x30">
    <title>Misfire Catalyst-Protection EQ</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Commanded fuel/air ratio (EQ, 1.0 = stoichiometric) used only while the misfire monitor sees heavy misfire, by engine speed (rows) and manifold pressure (columns, 20 to 200 kPa). Catalyst protection: do not tune. Effect: fuelling during heavy misfire only (catalyst protection) Evidence: ledger:E1587</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>kPa (manifold pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="20" />
      <LABEL index="1" value="31.25" />
      <LABEL index="2" value="42.5" />
      <LABEL index="3" value="53.75" />
      <LABEL index="4" value="65" />
      <LABEL index="5" value="76.25" />
      <LABEL index="6" value="87.5" />
      <LABEL index="7" value="98.75" />
      <LABEL index="8" value="110" />
      <LABEL index="9" value="121.25" />
      <LABEL index="10" value="132.5" />
      <LABEL index="11" value="143.75" />
      <LABEL index="12" value="155" />
      <LABEL index="13" value="166.25" />
      <LABEL index="14" value="177.5" />
      <LABEL index="15" value="188.75" />
      <LABEL index="16" value="200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x27070" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>EQ (fuel/air, 1.0 = stoich; lambda = 1/EQ)</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>63.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7C0" flags="0x30">
    <title>Idle Underspeed Spark vs RPM Error (P/N)</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Idle spark correction in degrees when engine speed is below the idle target, in Park / Neutral, by the absolute speed error. Effect: raise = more spark advance added below the idle target in Park / Neutral Evidence: ledger:E1587</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm error (x0.75 in most modes)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <LABEL index="9" value="144" />
      <LABEL index="10" value="160" />
      <LABEL index="11" value="176" />
      <LABEL index="12" value="192" />
      <LABEL index="13" value="208" />
      <LABEL index="14" value="224" />
      <LABEL index="15" value="240" />
      <LABEL index="16" value="256" />
      <LABEL index="17" value="272" />
      <LABEL index="18" value="288" />
      <LABEL index="19" value="304" />
      <LABEL index="20" value="320" />
      <LABEL index="21" value="336" />
      <LABEL index="22" value="352" />
      <LABEL index="23" value="368" />
      <LABEL index="24" value="384" />
      <LABEL index="25" value="400" />
      <LABEL index="26" value="416" />
      <LABEL index="27" value="432" />
      <LABEL index="28" value="448" />
      <LABEL index="29" value="464" />
      <LABEL index="30" value="480" />
      <LABEL index="31" value="496" />
      <LABEL index="32" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E93C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7C1" flags="0x30">
    <title>Idle Overspeed Spark vs RPM Error (P/N)</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Idle spark correction in degrees when engine speed is above the idle target, in Park / Neutral, by the absolute speed error. Effect: more negative = more spark retard above the idle target in Park / Neutral Evidence: ledger:E1587</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm error (x0.75 in most modes)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <LABEL index="9" value="144" />
      <LABEL index="10" value="160" />
      <LABEL index="11" value="176" />
      <LABEL index="12" value="192" />
      <LABEL index="13" value="208" />
      <LABEL index="14" value="224" />
      <LABEL index="15" value="240" />
      <LABEL index="16" value="256" />
      <LABEL index="17" value="272" />
      <LABEL index="18" value="288" />
      <LABEL index="19" value="304" />
      <LABEL index="20" value="320" />
      <LABEL index="21" value="336" />
      <LABEL index="22" value="352" />
      <LABEL index="23" value="368" />
      <LABEL index="24" value="384" />
      <LABEL index="25" value="400" />
      <LABEL index="26" value="416" />
      <LABEL index="27" value="432" />
      <LABEL index="28" value="448" />
      <LABEL index="29" value="464" />
      <LABEL index="30" value="480" />
      <LABEL index="31" value="496" />
      <LABEL index="32" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E984" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7C2" flags="0x30">
    <title>Idle Underspeed Spark vs RPM Error (In Gear)</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Idle spark correction in degrees when engine speed is below the idle target, in gear, by the absolute speed error. Effect: raise = more spark advance added below the idle target in gear Evidence: ledger:E1587</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm error (x0.75 in most modes)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <LABEL index="9" value="144" />
      <LABEL index="10" value="160" />
      <LABEL index="11" value="176" />
      <LABEL index="12" value="192" />
      <LABEL index="13" value="208" />
      <LABEL index="14" value="224" />
      <LABEL index="15" value="240" />
      <LABEL index="16" value="256" />
      <LABEL index="17" value="272" />
      <LABEL index="18" value="288" />
      <LABEL index="19" value="304" />
      <LABEL index="20" value="320" />
      <LABEL index="21" value="336" />
      <LABEL index="22" value="352" />
      <LABEL index="23" value="368" />
      <LABEL index="24" value="384" />
      <LABEL index="25" value="400" />
      <LABEL index="26" value="416" />
      <LABEL index="27" value="432" />
      <LABEL index="28" value="448" />
      <LABEL index="29" value="464" />
      <LABEL index="30" value="480" />
      <LABEL index="31" value="496" />
      <LABEL index="32" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E9CC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7C3" flags="0x30">
    <title>Idle Overspeed Spark vs RPM Error (In Gear)</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Idle spark correction in degrees when engine speed is above the idle target, in gear, by the absolute speed error. Effect: more negative = more spark retard above the idle target in gear Evidence: ledger:E1587</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm error (x0.75 in most modes)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="16" />
      <LABEL index="2" value="32" />
      <LABEL index="3" value="48" />
      <LABEL index="4" value="64" />
      <LABEL index="5" value="80" />
      <LABEL index="6" value="96" />
      <LABEL index="7" value="112" />
      <LABEL index="8" value="128" />
      <LABEL index="9" value="144" />
      <LABEL index="10" value="160" />
      <LABEL index="11" value="176" />
      <LABEL index="12" value="192" />
      <LABEL index="13" value="208" />
      <LABEL index="14" value="224" />
      <LABEL index="15" value="240" />
      <LABEL index="16" value="256" />
      <LABEL index="17" value="272" />
      <LABEL index="18" value="288" />
      <LABEL index="19" value="304" />
      <LABEL index="20" value="320" />
      <LABEL index="21" value="336" />
      <LABEL index="22" value="352" />
      <LABEL index="23" value="368" />
      <LABEL index="24" value="384" />
      <LABEL index="25" value="400" />
      <LABEL index="26" value="416" />
      <LABEL index="27" value="432" />
      <LABEL index="28" value="448" />
      <LABEL index="29" value="464" />
      <LABEL index="30" value="480" />
      <LABEL index="31" value="496" />
      <LABEL index="32" value="512" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EA14" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>3</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X*0.0078125"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7C4" flags="0x30">
    <title>Injector Offset vs Battery Voltage vs Vacuum</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system, not confirmed on a vehicle. Injector offset (dead time) in ms by battery voltage (rows) and manifold vacuum (columns). The engine adds it to every injector pulse in the injector timer, on the same 1/128 ms clock as the pulse width. The vacuum axis runs from 120 kPa of boost to 80 kPa of vacuum. Used when Injector Offset Table Select is 0; otherwise the MAP based table is used. Effect: raise = longer injector pulse at that voltage and vacuum (richer) Evidence: ledger:E1593</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>kPa vacuum (barometric minus manifold pressure; negative values are boost)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-120" />
      <LABEL index="1" value="-113.75" />
      <LABEL index="2" value="-107.5" />
      <LABEL index="3" value="-101.25" />
      <LABEL index="4" value="-95" />
      <LABEL index="5" value="-88.75" />
      <LABEL index="6" value="-82.5" />
      <LABEL index="7" value="-76.25" />
      <LABEL index="8" value="-70" />
      <LABEL index="9" value="-63.75" />
      <LABEL index="10" value="-57.5" />
      <LABEL index="11" value="-51.25" />
      <LABEL index="12" value="-45" />
      <LABEL index="13" value="-38.75" />
      <LABEL index="14" value="-32.5" />
      <LABEL index="15" value="-26.25" />
      <LABEL index="16" value="-20" />
      <LABEL index="17" value="-13.75" />
      <LABEL index="18" value="-7.5" />
      <LABEL index="19" value="-1.25" />
      <LABEL index="20" value="5" />
      <LABEL index="21" value="11.25" />
      <LABEL index="22" value="17.5" />
      <LABEL index="23" value="23.75" />
      <LABEL index="24" value="30" />
      <LABEL index="25" value="36.25" />
      <LABEL index="26" value="42.5" />
      <LABEL index="27" value="48.75" />
      <LABEL index="28" value="55" />
      <LABEL index="29" value="61.25" />
      <LABEL index="30" value="67.5" />
      <LABEL index="31" value="73.75" />
      <LABEL index="32" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>V (battery)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="4.5" />
      <LABEL index="1" value="5" />
      <LABEL index="2" value="5.5" />
      <LABEL index="3" value="6" />
      <LABEL index="4" value="6.5" />
      <LABEL index="5" value="7" />
      <LABEL index="6" value="7.5" />
      <LABEL index="7" value="8" />
      <LABEL index="8" value="8.5" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="9.5" />
      <LABEL index="11" value="10" />
      <LABEL index="12" value="10.5" />
      <LABEL index="13" value="11" />
      <LABEL index="14" value="11.5" />
      <LABEL index="15" value="12" />
      <LABEL index="16" value="12.5" />
      <LABEL index="17" value="13" />
      <LABEL index="18" value="13.5" />
      <LABEL index="19" value="14" />
      <LABEL index="20" value="14.5" />
      <LABEL index="21" value="15" />
      <LABEL index="22" value="15.5" />
      <LABEL index="23" value="16" />
      <LABEL index="24" value="16.5" />
      <LABEL index="25" value="17" />
      <LABEL index="26" value="17.5" />
      <LABEL index="27" value="18" />
      <LABEL index="28" value="18.5" />
      <LABEL index="29" value="19" />
      <LABEL index="30" value="19.5" />
      <LABEL index="31" value="20" />
      <LABEL index="32" value="20.5" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x25412" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>ms</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7C5" flags="0x30">
    <title>Injector flow rate vs kPa vacuum</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system, not confirmed on a vehicle. Injector flow rate in g/s by manifold vacuum; the vacuum axis runs from 120 kPa of boost to 80 kPa of vacuum. The pulse width calculation divides the fuel mass by this flow. Effect: raise = shorter injector pulse for the same fuel (leaner) Evidence: ledger:E1593</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>kPa vacuum (barometric minus manifold pressure; negative values are boost)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-120" />
      <LABEL index="1" value="-113.75" />
      <LABEL index="2" value="-107.5" />
      <LABEL index="3" value="-101.25" />
      <LABEL index="4" value="-95" />
      <LABEL index="5" value="-88.75" />
      <LABEL index="6" value="-82.5" />
      <LABEL index="7" value="-76.25" />
      <LABEL index="8" value="-70" />
      <LABEL index="9" value="-63.75" />
      <LABEL index="10" value="-57.5" />
      <LABEL index="11" value="-51.25" />
      <LABEL index="12" value="-45" />
      <LABEL index="13" value="-38.75" />
      <LABEL index="14" value="-32.5" />
      <LABEL index="15" value="-26.25" />
      <LABEL index="16" value="-20" />
      <LABEL index="17" value="-13.75" />
      <LABEL index="18" value="-7.5" />
      <LABEL index="19" value="-1.25" />
      <LABEL index="20" value="5" />
      <LABEL index="21" value="11.25" />
      <LABEL index="22" value="17.5" />
      <LABEL index="23" value="23.75" />
      <LABEL index="24" value="30" />
      <LABEL index="25" value="36.25" />
      <LABEL index="26" value="42.5" />
      <LABEL index="27" value="48.75" />
      <LABEL index="28" value="55" />
      <LABEL index="29" value="61.25" />
      <LABEL index="30" value="67.5" />
      <LABEL index="31" value="73.75" />
      <LABEL index="32" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26520" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>g/s</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7C6" flags="0x30">
    <title>Purge Demand - Factor vs Manifold Vacuum</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system, not confirmed on a vehicle. Canister purge amount: factor on the purge flow request, by manifold vacuum (120 kPa of boost to 80 kPa of vacuum). 1.0 = no change. Effect: raise = more purge valve opening at that manifold vacuum Evidence: ledger:E1593</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>kPa vacuum (barometric minus manifold pressure; negative values are boost)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-120" />
      <LABEL index="1" value="-113.75" />
      <LABEL index="2" value="-107.5" />
      <LABEL index="3" value="-101.25" />
      <LABEL index="4" value="-95" />
      <LABEL index="5" value="-88.75" />
      <LABEL index="6" value="-82.5" />
      <LABEL index="7" value="-76.25" />
      <LABEL index="8" value="-70" />
      <LABEL index="9" value="-63.75" />
      <LABEL index="10" value="-57.5" />
      <LABEL index="11" value="-51.25" />
      <LABEL index="12" value="-45" />
      <LABEL index="13" value="-38.75" />
      <LABEL index="14" value="-32.5" />
      <LABEL index="15" value="-26.25" />
      <LABEL index="16" value="-20" />
      <LABEL index="17" value="-13.75" />
      <LABEL index="18" value="-7.5" />
      <LABEL index="19" value="-1.25" />
      <LABEL index="20" value="5" />
      <LABEL index="21" value="11.25" />
      <LABEL index="22" value="17.5" />
      <LABEL index="23" value="23.75" />
      <LABEL index="24" value="30" />
      <LABEL index="25" value="36.25" />
      <LABEL index="26" value="42.5" />
      <LABEL index="27" value="48.75" />
      <LABEL index="28" value="55" />
      <LABEL index="29" value="61.25" />
      <LABEL index="30" value="67.5" />
      <LABEL index="31" value="73.75" />
      <LABEL index="32" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24204" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>multiplier</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7C7" flags="0x30">
    <title>Purge Flow - Reference Flow vs Manifold Vacuum</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system, not confirmed on a vehicle. Canister purge: flow the purge valve can pass at each manifold vacuum (120 kPa of boost to 80 kPa of vacuum). Long term fuel trim uses it to scale the purge learned correction. Effect: raise = the fuel trim side assumes more purge flow at that vacuum Evidence: ledger:E1593</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>kPa vacuum (barometric minus manifold pressure; negative values are boost)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-120" />
      <LABEL index="1" value="-113.75" />
      <LABEL index="2" value="-107.5" />
      <LABEL index="3" value="-101.25" />
      <LABEL index="4" value="-95" />
      <LABEL index="5" value="-88.75" />
      <LABEL index="6" value="-82.5" />
      <LABEL index="7" value="-76.25" />
      <LABEL index="8" value="-70" />
      <LABEL index="9" value="-63.75" />
      <LABEL index="10" value="-57.5" />
      <LABEL index="11" value="-51.25" />
      <LABEL index="12" value="-45" />
      <LABEL index="13" value="-38.75" />
      <LABEL index="14" value="-32.5" />
      <LABEL index="15" value="-26.25" />
      <LABEL index="16" value="-20" />
      <LABEL index="17" value="-13.75" />
      <LABEL index="18" value="-7.5" />
      <LABEL index="19" value="-1.25" />
      <LABEL index="20" value="5" />
      <LABEL index="21" value="11.25" />
      <LABEL index="22" value="17.5" />
      <LABEL index="23" value="23.75" />
      <LABEL index="24" value="30" />
      <LABEL index="25" value="36.25" />
      <LABEL index="26" value="42.5" />
      <LABEL index="27" value="48.75" />
      <LABEL index="28" value="55" />
      <LABEL index="29" value="61.25" />
      <LABEL index="30" value="67.5" />
      <LABEL index="31" value="73.75" />
      <LABEL index="32" value="80" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24452" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>flow units</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7C8" flags="0x30">
    <title>Intake Air Temp Sensor - Temperature Points</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system, not confirmed on a vehicle. Intake air temperature at each of the 33 sensor resistance points; the engine interpolates between them. Effect: reported and used intake air temperature Evidence: ledger:E1593</description>
    <CATEGORYMEM index="0" category="12" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>point</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <LABEL index="17" value="17" />
      <LABEL index="18" value="18" />
      <LABEL index="19" value="19" />
      <LABEL index="20" value="20" />
      <LABEL index="21" value="21" />
      <LABEL index="22" value="22" />
      <LABEL index="23" value="23" />
      <LABEL index="24" value="24" />
      <LABEL index="25" value="25" />
      <LABEL index="26" value="26" />
      <LABEL index="27" value="27" />
      <LABEL index="28" value="28" />
      <LABEL index="29" value="29" />
      <LABEL index="30" value="30" />
      <LABEL index="31" value="31" />
      <LABEL index="32" value="32" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x29A9A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>degC</units>
      <decimalpl>2</decimalpl>
      <min>-256.000000</min>
      <max>255.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7C9" flags="0x30">
    <title>Idle Speed Control - Airflow Max (In Gear)</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the H3 item of the same function, not confirmed on a vehicle. Maximum airflow the idle speed controller may command in in gear, by desired idle rpm (rows) and coolant (columns). The A/C offset is added on top. Values and axes as read on this OS. On this OS the table is 9 x 9. Effect: raise = more idle air at that desired rpm and coolant (keep max &gt;= min) Evidence: ledger:E1593</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-21" />
      <LABEL index="2" value="-2" />
      <LABEL index="3" value="17" />
      <LABEL index="4" value="36" />
      <LABEL index="5" value="55" />
      <LABEL index="6" value="74" />
      <LABEL index="7" value="93" />
      <LABEL index="8" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="550" />
      <LABEL index="1" value="650" />
      <LABEL index="2" value="750" />
      <LABEL index="3" value="850" />
      <LABEL index="4" value="950" />
      <LABEL index="5" value="1050" />
      <LABEL index="6" value="1150" />
      <LABEL index="7" value="1250" />
      <LABEL index="8" value="1350" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22214" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7CA" flags="0x30">
    <title>Idle Speed Control - Airflow Min (In Gear)</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the H3 item of the same function, not confirmed on a vehicle. Minimum airflow the idle speed controller may command in in gear, by desired idle rpm (rows) and coolant (columns). The A/C offset is added on top. Values and axes as read on this OS. On this OS the table is 9 x 9. Effect: raise = more idle air at that desired rpm and coolant (keep max &gt;= min) Evidence: ledger:E1593</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-21" />
      <LABEL index="2" value="-2" />
      <LABEL index="3" value="17" />
      <LABEL index="4" value="36" />
      <LABEL index="5" value="55" />
      <LABEL index="6" value="74" />
      <LABEL index="7" value="93" />
      <LABEL index="8" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="550" />
      <LABEL index="1" value="650" />
      <LABEL index="2" value="750" />
      <LABEL index="3" value="850" />
      <LABEL index="4" value="950" />
      <LABEL index="5" value="1050" />
      <LABEL index="6" value="1150" />
      <LABEL index="7" value="1250" />
      <LABEL index="8" value="1350" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x222BC" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7CB" flags="0x30">
    <title>Transient Fuel - Wall Evaporation Fraction vs MAP vs Temp</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the H3 item of the same function, not confirmed on a vehicle. Fraction of the port wall fuel film that evaporates into the cylinder each update (the wall-wetting time constant), by MAP (rows) and port temperature (columns). Values and axes as read on this OS. On this OS the table is 17 x 17. Effect: raise = wall film dries faster (shorter tip-in/tip-out fuel corrections) Evidence: ledger:E1593</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (modelled temp)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-24" />
      <LABEL index="2" value="-8" />
      <LABEL index="3" value="8" />
      <LABEL index="4" value="24" />
      <LABEL index="5" value="40" />
      <LABEL index="6" value="56" />
      <LABEL index="7" value="72" />
      <LABEL index="8" value="88" />
      <LABEL index="9" value="104" />
      <LABEL index="10" value="120" />
      <LABEL index="11" value="136" />
      <LABEL index="12" value="152" />
      <LABEL index="13" value="168" />
      <LABEL index="14" value="184" />
      <LABEL index="15" value="200" />
      <LABEL index="16" value="216" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="20" />
      <LABEL index="1" value="31.25" />
      <LABEL index="2" value="42.5" />
      <LABEL index="3" value="53.75" />
      <LABEL index="4" value="65" />
      <LABEL index="5" value="76.25" />
      <LABEL index="6" value="87.5" />
      <LABEL index="7" value="98.75" />
      <LABEL index="8" value="110" />
      <LABEL index="9" value="121.25" />
      <LABEL index="10" value="132.5" />
      <LABEL index="11" value="143.75" />
      <LABEL index="12" value="155" />
      <LABEL index="13" value="166.25" />
      <LABEL index="14" value="177.5" />
      <LABEL index="15" value="188.75" />
      <LABEL index="16" value="200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2692C" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>fraction per update</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7CC" flags="0x30">
    <title>Idle Spark Maximum vs RPM vs Airmass</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system, not confirmed on a vehicle. Upper limit on spark advance in the idle spark mode, by cylinder airmass (rows) and engine speed (columns, 400 to 1600 rpm). The coolant and intake air corrections below are added to it, and each cylinder&#x27;s idle spark is held at or below the result. Effect: raise = allows more idle spark advance Evidence: ledger:E1605</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="600" />
      <LABEL index="2" value="800" />
      <LABEL index="3" value="1000" />
      <LABEL index="4" value="1200" />
      <LABEL index="5" value="1400" />
      <LABEL index="6" value="1600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl (cylinder airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2D9B5" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X/2"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7CD" flags="0x30">
    <title>Idle Spark Maximum Coolant Correction vs Coolant vs Airmass</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system, not confirmed on a vehicle. Degrees added to the idle spark maximum, by cylinder airmass (rows) and coolant temperature (columns); multiplied by the coolant correction multiplier by engine speed before it is added. Effect: raise = more idle spark advance allowed at that coolant temperature Evidence: ledger:E1605</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl (cylinder airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E095" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X/2"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7CE" flags="0x30">
    <title>Idle Spark Maximum Coolant Correction Multiplier vs RPM</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system, not confirmed on a vehicle. Multiplier (0 to 1) on the coolant correction of the idle spark maximum, by engine speed. Effect: raise = more of the coolant correction applies at that speed Evidence: ledger:E1605</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E2C8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7CF" flags="0x30">
    <title>Idle Spark Maximum Intake Air Correction vs IAT vs Airmass</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system, not confirmed on a vehicle. Degrees added to the idle spark maximum, by cylinder airmass (rows) and intake air temperature (columns); multiplied by the intake air correction multiplier by engine speed before it is added. Effect: raise = more idle spark advance allowed at that intake air temperature Evidence: ledger:E1605</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (intake air)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl (cylinder airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E2ED" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X/2"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7D0" flags="0x30">
    <title>Idle Spark Maximum Intake Air Correction Multiplier vs RPM</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system, not confirmed on a vehicle. Multiplier (0 to 1) on the intake air correction of the idle spark maximum, by engine speed. Effect: raise = more of the intake air correction applies at that speed Evidence: ledger:E1605</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="512" />
      <LABEL index="2" value="1024" />
      <LABEL index="3" value="1536" />
      <LABEL index="4" value="2048" />
      <LABEL index="5" value="2560" />
      <LABEL index="6" value="3072" />
      <LABEL index="7" value="3584" />
      <LABEL index="8" value="4096" />
      <LABEL index="9" value="4608" />
      <LABEL index="10" value="5120" />
      <LABEL index="11" value="5632" />
      <LABEL index="12" value="6144" />
      <LABEL index="13" value="6656" />
      <LABEL index="14" value="7168" />
      <LABEL index="15" value="7680" />
      <LABEL index="16" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2E520" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>0.999985</max>
      <MATH equation="X/65536"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7D1" flags="0x30">
    <title>Closed Throttle Coast Spark vs RPM vs Airmass</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system, not confirmed on a vehicle. Spark advance for every cylinder while the spark mode sequencer is in its closed throttle coast mode (entered from the idle spark mode with the throttle closed), by cylinder airmass (rows) and engine speed (columns, 0 to 8192 rpm). Knock retard and the spark minimum still apply afterwards. Effect: raise = more spark advance while coasting with the throttle closed Evidence: ledger:E1605</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl (cylinder airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EB2D" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X/2"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7D2" flags="0x30">
    <title>Volumetric Efficiency vs RPM vs MAP</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system, not confirmed on a vehicle. Volumetric efficiency used to compute the airmass in each cylinder, by engine speed (rows) and manifold pressure (columns, 15 to 215 kPa): airmass per cylinder = this value x manifold pressure / charge temperature. Stored in mg K / kPa per cylinder, the same unit as the H3 VE tables. This family has one VE table instead of the H3&#x27;s five cam-phase tables. Effect: raise = more calculated airmass at that speed and pressure (more fuel, less spark) Evidence: ledger:E1614</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>kPa (manifold pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="15" />
      <LABEL index="1" value="21.25" />
      <LABEL index="2" value="27.5" />
      <LABEL index="3" value="33.75" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="46.25" />
      <LABEL index="6" value="52.5" />
      <LABEL index="7" value="58.75" />
      <LABEL index="8" value="65" />
      <LABEL index="9" value="71.25" />
      <LABEL index="10" value="77.5" />
      <LABEL index="11" value="83.75" />
      <LABEL index="12" value="90" />
      <LABEL index="13" value="96.25" />
      <LABEL index="14" value="102.5" />
      <LABEL index="15" value="108.75" />
      <LABEL index="16" value="115" />
      <LABEL index="17" value="121.25" />
      <LABEL index="18" value="127.5" />
      <LABEL index="19" value="133.75" />
      <LABEL index="20" value="140" />
      <LABEL index="21" value="146.25" />
      <LABEL index="22" value="152.5" />
      <LABEL index="23" value="158.75" />
      <LABEL index="24" value="165" />
      <LABEL index="25" value="171.25" />
      <LABEL index="26" value="177.5" />
      <LABEL index="27" value="183.75" />
      <LABEL index="28" value="190" />
      <LABEL index="29" value="196.25" />
      <LABEL index="30" value="202.5" />
      <LABEL index="31" value="208.75" />
      <LABEL index="32" value="215" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2BE0A" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mg K/kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7D3" flags="0x30">
    <title>Pre-Sync Start Pulse Fuel vs Coolant vs Soak Time (dormant)</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Fuel mass per injection, in mg, of the pre-sync start pulse: one pulse fired into every cylinder when cranking starts, before the PCM has synchronised to the crankshaft. By engine-off soak time (rows) and coolant temperature (columns); multiplied by the Pre-Sync Start Pulse Barometric Factor. Both axes are stored breakpoints (the shared Fuel - Coolant Breakpoints and the Cranking Fuel - Soak Time Breakpoints): editing those moves these axes. The pre-sync start pulse sequence is switched off on this calibration, so this has no effect on the stock calibration (dormant). Effect: none while the pre-sync start pulse sequence is switched off (dormant) Evidence: ledger:E1689</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-34" />
      <LABEL index="2" value="-28" />
      <LABEL index="3" value="-22" />
      <LABEL index="4" value="-16" />
      <LABEL index="5" value="-10" />
      <LABEL index="6" value="-4" />
      <LABEL index="7" value="2" />
      <LABEL index="8" value="14" />
      <LABEL index="9" value="26" />
      <LABEL index="10" value="38" />
      <LABEL index="11" value="50" />
      <LABEL index="12" value="62" />
      <LABEL index="13" value="74" />
      <LABEL index="14" value="86" />
      <LABEL index="15" value="98" />
      <LABEL index="16" value="110" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>s (engine-off soak time)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="5" />
      <LABEL index="3" value="10" />
      <LABEL index="4" value="20" />
      <LABEL index="5" value="30" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="120" />
      <LABEL index="8" value="240" />
      <LABEL index="9" value="600" />
      <LABEL index="10" value="1200" />
      <LABEL index="11" value="1800" />
      <LABEL index="12" value="3600" />
      <LABEL index="13" value="7200" />
      <LABEL index="14" value="10800" />
      <LABEL index="15" value="14400" />
      <LABEL index="16" value="21600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2477C" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mg</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>2047.968750</max>
      <MATH equation="X/32"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7D4" flags="0x30">
    <title>Pre-Sync Start Pulse Barometric Factor (dormant)</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Multiplier on the pre-sync start pulse fuel (Pre-Sync Start Pulse Fuel vs Coolant vs Soak Time), by barometric pressure. 1.0 = no change. The pre-sync start pulse sequence is switched off on this calibration, so this has no effect on the stock calibration (dormant). Effect: none while the pre-sync start pulse sequence is switched off (dormant) Evidence: ledger:E1689</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (barometric pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="65" />
      <LABEL index="1" value="70" />
      <LABEL index="2" value="75" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="85" />
      <LABEL index="5" value="90" />
      <LABEL index="6" value="95" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x24760" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>x</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>7.999878</max>
      <MATH equation="X/8192"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7D5" flags="0x30">
    <title>Cranking Fuel - Soak Time Breakpoints, shared (axis, edit with care)</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Stored engine-off soak time breakpoints, in seconds, shared by the cranking fuel tables indexed by soak time (Cranking FA Mult Stage 1 and the pre-sync start pulse fuel): editing them moves the soak time axis of all of those tables at once. Must stay increasing. Effect: moves the axis of every table that uses it: edit with care Evidence: ledger:E1689</description>
    <CATEGORYMEM index="0" category="2" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="1" />
      <LABEL index="2" value="2" />
      <LABEL index="3" value="3" />
      <LABEL index="4" value="4" />
      <LABEL index="5" value="5" />
      <LABEL index="6" value="6" />
      <LABEL index="7" value="7" />
      <LABEL index="8" value="8" />
      <LABEL index="9" value="9" />
      <LABEL index="10" value="10" />
      <LABEL index="11" value="11" />
      <LABEL index="12" value="12" />
      <LABEL index="13" value="13" />
      <LABEL index="14" value="14" />
      <LABEL index="15" value="15" />
      <LABEL index="16" value="16" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x26DEC" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>s</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7D6" flags="0x30">
    <title>Spark Mode Ramp - Cranking to Idle vs Coolant</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Spark reference ramp: when the spark mode changes (cranking, idle, closed throttle coast, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This curve is the ramp from cranking to idle once the engine is running, by coolant temperature. Effect: raise = slower blend from cranking spark to idle spark at that coolant temperature Evidence: ledger:E1689</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>10</indexcount>
      <units>degC (coolant)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-20" />
      <LABEL index="2" value="0" />
      <LABEL index="3" value="20" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="60" />
      <LABEL index="6" value="80" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="120" />
      <LABEL index="9" value="140" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EF70" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="10" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>update cycles</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7D7" flags="0x30">
    <title>Spark Mode Ramp - Idle to Off Idle vs Throttle</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Spark reference ramp: when the spark mode changes (cranking, idle, closed throttle coast, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This curve is the ramp from idle to off idle, by throttle when the change happens. Effect: raise = slower blend from idle spark to off idle spark at that throttle Evidence: ledger:E1689</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>% throttle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EF8E" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>update cycles</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7D8" flags="0x30">
    <title>Spark Mode Ramp - Into Decel Fuel Cut vs RPM</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Spark reference ramp: when the spark mode changes (cranking, idle, closed throttle coast, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This curve is the ramp into decel fuel cut (from closed throttle coast or off idle), by engine speed. Effect: raise = slower blend into the decel fuel cut spark at that engine speed Evidence: ledger:E1689</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EFE4" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>update cycles</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7D9" flags="0x30">
    <title>Spark Mode Ramp - Decel Fuel Cut End to Off Idle vs Throttle</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Spark reference ramp: when the spark mode changes (cranking, idle, closed throttle coast, decel fuel cut, off idle), the spark reference blends from the old mode&#x27;s spark to the new one over this many update cycles (0 = jump at once). This curve is the ramp from decel fuel cut back to off idle, by throttle (0 to 100 % in 10 % steps). Effect: raise = slower blend from the decel fuel cut spark back to off idle spark at that throttle Evidence: ledger:E1689</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>11</indexcount>
      <units>% throttle</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2EFA8" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="11" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>update cycles</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7DA" flags="0x30">
    <title>Alternate VE Table A vs Throttle Area vs RPM (airflow mode 2)</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system (OS 12601774), not confirmed on a vehicle. Alternate volumetric efficiency table A for airflow mode 2, which computes the VE from throttle area instead of manifold pressure, by throttle area (rows) and engine speed (columns). Tables A and B are blended by barometric pressure and the result replaces the normal VE value, in the same unit. Whether this calibration ever enters airflow mode 2 has not been checked. Effect: raise = more calculated airmass in airflow mode 2 Evidence: ledger:E1800</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>% throttle area</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C27A" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mg K/kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7DB" flags="0x30">
    <title>Alternate VE Table B vs Throttle Area vs RPM (airflow mode 2)</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system (OS 12601774), not confirmed on a vehicle. Alternate volumetric efficiency table B for airflow mode 2 (VE from throttle area), by throttle area (rows) and engine speed (columns); blended with table A by barometric pressure. Whether this calibration ever enters airflow mode 2 has not been checked. Effect: raise = more calculated airmass in airflow mode 2 Evidence: ledger:E1800</description>
    <CATEGORYMEM index="0" category="3" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>% throttle area</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="6.25" />
      <LABEL index="2" value="12.5" />
      <LABEL index="3" value="18.75" />
      <LABEL index="4" value="25" />
      <LABEL index="5" value="31.25" />
      <LABEL index="6" value="37.5" />
      <LABEL index="7" value="43.75" />
      <LABEL index="8" value="50" />
      <LABEL index="9" value="56.25" />
      <LABEL index="10" value="62.5" />
      <LABEL index="11" value="68.75" />
      <LABEL index="12" value="75" />
      <LABEL index="13" value="81.25" />
      <LABEL index="14" value="87.5" />
      <LABEL index="15" value="93.75" />
      <LABEL index="16" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2C4C2" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>mg K/kPa</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>4095.937500</max>
      <MATH equation="X/16"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7DC" flags="0x30">
    <title>Cold Off-Idle Spark Retard (main spark)</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system (OS 12601774), not confirmed on a vehicle. Spark retard off idle (spark mode 5) below 6000 rpm, by cylinder airmass (rows) and engine speed (columns), multiplied by the coolant factor curve. The larger of this and the catalyst light-off retard is taken off main spark. On this operating system the cells are 16-bit (1/128 deg per count); the H3 table holds bytes. Effect: raise = more spark retard off idle on a cold engine (less torque, more exhaust heat) Evidence: ledger:E1805</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="400" />
      <LABEL index="1" value="800" />
      <LABEL index="2" value="1200" />
      <LABEL index="3" value="1600" />
      <LABEL index="4" value="2000" />
      <LABEL index="5" value="2400" />
      <LABEL index="6" value="2800" />
      <LABEL index="7" value="3200" />
      <LABEL index="8" value="3600" />
      <LABEL index="9" value="4000" />
      <LABEL index="10" value="4400" />
      <LABEL index="11" value="4800" />
      <LABEL index="12" value="5200" />
      <LABEL index="13" value="5600" />
      <LABEL index="14" value="6000" />
      <LABEL index="15" value="6400" />
      <LABEL index="16" value="6800" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <LABEL index="9" value="0.44" />
      <LABEL index="10" value="0.48" />
      <LABEL index="11" value="0.52" />
      <LABEL index="12" value="0.56" />
      <LABEL index="13" value="0.6" />
      <LABEL index="14" value="0.64" />
      <LABEL index="15" value="0.68" />
      <LABEL index="16" value="0.72" />
      <LABEL index="17" value="0.76" />
      <LABEL index="18" value="0.8" />
      <LABEL index="19" value="0.84" />
      <LABEL index="20" value="0.88" />
      <LABEL index="21" value="0.92" />
      <LABEL index="22" value="0.96" />
      <LABEL index="23" value="1" />
      <LABEL index="24" value="1.04" />
      <LABEL index="25" value="1.08" />
      <LABEL index="26" value="1.12" />
      <LABEL index="27" value="1.16" />
      <LABEL index="28" value="1.2" />
      <LABEL index="29" value="1.24" />
      <LABEL index="30" value="1.28" />
      <LABEL index="31" value="1.32" />
      <LABEL index="32" value="1.36" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2D026" mmedelementsizebits="16" mmedrowcount="33" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>deg retard</units>
      <decimalpl>2</decimalpl>
      <min>0.000000</min>
      <max>511.992188</max>
      <MATH equation="X/128"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7DD" flags="0x30">
    <title>Cold Off-Idle Spark Retard - Coolant Factor</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system (OS 12601774), not confirmed on a vehicle. Multiplier on the cold off-idle spark retard table by coolant temperature (32768 = 1.0 on this operating system; the H3 curve holds bytes, 128 = 1.0). Effect: raise = keep more of the cold off-idle spark retard at that coolant temperature Evidence: ledger:E1805</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-30" />
      <LABEL index="2" value="-20" />
      <LABEL index="3" value="-10" />
      <LABEL index="4" value="0" />
      <LABEL index="5" value="10" />
      <LABEL index="6" value="20" />
      <LABEL index="7" value="30" />
      <LABEL index="8" value="40" />
      <LABEL index="9" value="50" />
      <LABEL index="10" value="60" />
      <LABEL index="11" value="70" />
      <LABEL index="12" value="80" />
      <LABEL index="13" value="90" />
      <LABEL index="14" value="100" />
      <LABEL index="15" value="110" />
      <LABEL index="16" value="120" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2D48A" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7DE" flags="0x30">
    <title>Cruise Control - Target Ramp-Down Step vs MAP x Speed</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system (OS 12601774), not confirmed on a vehicle. Largest step per pass by which the cruise control demand may fall toward the Cruise Control Demand Target table, by engine load (MAP, rows, 0 to 200 kPa) and vehicle speed (columns, 38 to 180 km/h). The step is this value times a separate scale, which is not zero on this operating system&#x27;s calibration (on the H3 it is 0 and this table is dormant there). This operating system&#x27;s table has 17 MAP rows where the H3 has 9. Values are the controller&#x27;s internal demand counts. Shown raw. DO NOT EDIT. Effect: raise = the cruise demand may fall faster toward its target Evidence: ledger:E1805</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.9" />
      <LABEL index="2" value="55.8" />
      <LABEL index="3" value="64.6" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.4" />
      <LABEL index="6" value="91.2" />
      <LABEL index="7" value="100.1" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.9" />
      <LABEL index="10" value="126.8" />
      <LABEL index="11" value="135.6" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.4" />
      <LABEL index="14" value="162.2" />
      <LABEL index="15" value="171.1" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="12.5" />
      <LABEL index="2" value="25" />
      <LABEL index="3" value="37.5" />
      <LABEL index="4" value="50" />
      <LABEL index="5" value="62.5" />
      <LABEL index="6" value="75" />
      <LABEL index="7" value="87.5" />
      <LABEL index="8" value="100" />
      <LABEL index="9" value="112.5" />
      <LABEL index="10" value="125" />
      <LABEL index="11" value="137.5" />
      <LABEL index="12" value="150" />
      <LABEL index="13" value="162.5" />
      <LABEL index="14" value="175" />
      <LABEL index="15" value="187.5" />
      <LABEL index="16" value="200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21AAE" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw (demand counts)</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7DF" flags="0x30">
    <title>Cruise Control Demand Target vs MAP x Speed</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the same item on the earlier Ecotec operating system (OS 12601774), not confirmed on a vehicle. Cruise control demand target by engine load (MAP, rows, 0 to 200 kPa) and vehicle speed (columns, 38 to 180 km/h). While cruise holds speed, the controller moves its demand toward this value corrected by the speed error, and the demand is turned into a throttle request by this operating system&#x27;s cruise throttle stage. This operating system&#x27;s table has 17 MAP rows where the H3 has 9. Values are the controller&#x27;s internal demand counts. Shown raw. DO NOT EDIT. Effect: changes the cruise demand the controller holds at that load and speed Evidence: ledger:E1805</description>
    <CATEGORYMEM index="0" category="4" />
    <XDFAXIS id="x">
      <indexcount>17</indexcount>
      <units>km/h (filtered vehicle speed)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="38" />
      <LABEL index="1" value="46.9" />
      <LABEL index="2" value="55.8" />
      <LABEL index="3" value="64.6" />
      <LABEL index="4" value="73.5" />
      <LABEL index="5" value="82.4" />
      <LABEL index="6" value="91.2" />
      <LABEL index="7" value="100.1" />
      <LABEL index="8" value="109" />
      <LABEL index="9" value="117.9" />
      <LABEL index="10" value="126.8" />
      <LABEL index="11" value="135.6" />
      <LABEL index="12" value="144.5" />
      <LABEL index="13" value="153.4" />
      <LABEL index="14" value="162.2" />
      <LABEL index="15" value="171.1" />
      <LABEL index="16" value="180" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>17</indexcount>
      <units>kPa (MAP)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="12.5" />
      <LABEL index="2" value="25" />
      <LABEL index="3" value="37.5" />
      <LABEL index="4" value="50" />
      <LABEL index="5" value="62.5" />
      <LABEL index="6" value="75" />
      <LABEL index="7" value="87.5" />
      <LABEL index="8" value="100" />
      <LABEL index="9" value="112.5" />
      <LABEL index="10" value="125" />
      <LABEL index="11" value="137.5" />
      <LABEL index="12" value="150" />
      <LABEL index="13" value="162.5" />
      <LABEL index="14" value="175" />
      <LABEL index="15" value="187.5" />
      <LABEL index="16" value="200" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x21CF6" mmedelementsizebits="16" mmedrowcount="17" mmedcolcount="17" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw (demand counts)</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7E0" flags="0x30">
    <title>Spark Reference - Cam Phase Adder Gain vs RPM x Airmass (inactive) (DO NOT EDIT)</title>
    <description>DO NOT TUNE - hardware characterisation. Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator (not carried from the Hummer H3 definition), not confirmed on a vehicle. Gain on the cam phase term that is added to the Spark Reference for Cam Target Reduction table, by airmass (rows) and engine speed (columns); the H3 has a single gain value here. This operating system&#x27;s code multiplies the gain by a cam phase fixed at 0, so the table has no effect on the spark reference. Shown as the raw stored value. Reference only: DO NOT EDIT. Effect: none on this operating system (the cam phase it multiplies is fixed at 0 in the code) Evidence: ledger:E1806</description>
    <CATEGORYMEM index="0" category="14" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>33</indexcount>
      <units>g/cyl (airmass)</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2FCE5" mmedelementsizebits="8" mmedrowcount="33" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>raw</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>255.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x7E1" flags="0x0">
    <title>Fuel Level Sender - In-Range Voltage Minimum</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator, not confirmed on a vehicle. The fuel level sender voltage is compared with this value: below this value the reading is out of range, and the in-range result changes how the fuel level filters are updated. The branch flips exactly at this value (executed edge test, same raw scale as the sender voltage word). Evidence: ledger:E1843</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x3724A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>9.999847</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/6553.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7E2" flags="0x0">
    <title>Fuel Level Sender - In-Range Voltage Maximum</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator, not confirmed on a vehicle. The fuel level sender voltage is compared with this value: above this value the reading is out of range, and the in-range result changes how the fuel level filters are updated. The branch flips exactly at this value (executed edge test, same raw scale as the sender voltage word). Evidence: ledger:E1843</description>
    <CATEGORYMEM index="0" category="12" />
    <EMBEDDEDDATA mmedaddress="0x3724C" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>V</units>
    <decimalpl>4</decimalpl>
    <min>0.000000</min>
    <max>9.999847</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/6553.6"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x7E3" flags="0x30">
    <title>Idle Speed Control - Airflow Max (Park/Neutral)</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator, not confirmed on a vehicle. Maximum airflow the idle speed controller may command in Park/Neutral, by desired idle rpm (rows) and coolant (columns). The A/C offset is added on top. On this OS the table is 9 x 9; its axes are the in-gear table&#x27;s (the same routine looks both up with the same row and column inputs). Effect: raise = more idle air at that desired rpm and coolant (keep max &gt;= min) Evidence: ledger:E1849</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-21" />
      <LABEL index="2" value="-2" />
      <LABEL index="3" value="17" />
      <LABEL index="4" value="36" />
      <LABEL index="5" value="55" />
      <LABEL index="6" value="74" />
      <LABEL index="7" value="93" />
      <LABEL index="8" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="550" />
      <LABEL index="1" value="650" />
      <LABEL index="2" value="750" />
      <LABEL index="3" value="850" />
      <LABEL index="4" value="950" />
      <LABEL index="5" value="1050" />
      <LABEL index="6" value="1150" />
      <LABEL index="7" value="1250" />
      <LABEL index="8" value="1350" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x220AC" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7E4" flags="0x30">
    <title>Idle Speed Control - Airflow Min (Park/Neutral)</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator, not confirmed on a vehicle. Minimum airflow the idle speed controller may command in Park/Neutral, by desired idle rpm (rows) and coolant (columns). The A/C offset is added on top. On this OS the table is 9 x 9; its axes are the in-gear table&#x27;s (the same routine looks both up with the same row and column inputs). Effect: raise = more idle air at that desired rpm and coolant (keep max &gt;= min) Evidence: ledger:E1849</description>
    <CATEGORYMEM index="0" category="5" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>degC</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="-40" />
      <LABEL index="1" value="-21" />
      <LABEL index="2" value="-2" />
      <LABEL index="3" value="17" />
      <LABEL index="4" value="36" />
      <LABEL index="5" value="55" />
      <LABEL index="6" value="74" />
      <LABEL index="7" value="93" />
      <LABEL index="8" value="112" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>rpm (desired idle)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="550" />
      <LABEL index="1" value="650" />
      <LABEL index="2" value="750" />
      <LABEL index="3" value="850" />
      <LABEL index="4" value="950" />
      <LABEL index="5" value="1050" />
      <LABEL index="6" value="1150" />
      <LABEL index="7" value="1250" />
      <LABEL index="8" value="1350" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x22154" mmedelementsizebits="16" mmedrowcount="9" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>g/s</units>
      <decimalpl>3</decimalpl>
      <min>-32.000000</min>
      <max>31.999023</max>
      <MATH equation="X/1024"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7E5" flags="0x30">
    <title>MAP Plausibility - High Limit</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the H3 check, not confirmed on a vehicle. MAP plausibility check: each sample in which manifold pressure is above the high limit or below the low limit for the current engine speed and throttle area counts as out of band; on this operating system both limits are first multiplied by the Limit Factor vs Barometric Pressure. This table is the high limit (kPa, before the factor) by engine speed (columns) and throttle area (rows). The H3 runs the same check with its enable switched off; whether it runs on this operating system has not been determined. Evidence: ledger:E1853</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="800" />
      <LABEL index="1" value="1600" />
      <LABEL index="2" value="2400" />
      <LABEL index="3" value="3200" />
      <LABEL index="4" value="4000" />
      <LABEL index="5" value="4800" />
      <LABEL index="6" value="5600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>11</indexcount>
      <units>% throttle area</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x3870C" mmedelementsizebits="16" mmedrowcount="11" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7E6" flags="0x30">
    <title>MAP Plausibility - Low Limit</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the H3 check, not confirmed on a vehicle. MAP plausibility check: each sample in which manifold pressure is above the high limit or below the low limit for the current engine speed and throttle area counts as out of band; on this operating system both limits are first multiplied by the Limit Factor vs Barometric Pressure. This table is the low limit (kPa, before the factor) by engine speed (columns) and throttle area (rows). The H3 runs the same check with its enable switched off; whether it runs on this operating system has not been determined. Evidence: ledger:E1853</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>7</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="800" />
      <LABEL index="1" value="1600" />
      <LABEL index="2" value="2400" />
      <LABEL index="3" value="3200" />
      <LABEL index="4" value="4000" />
      <LABEL index="5" value="4800" />
      <LABEL index="6" value="5600" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>11</indexcount>
      <units>% throttle area</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="10" />
      <LABEL index="2" value="20" />
      <LABEL index="3" value="30" />
      <LABEL index="4" value="40" />
      <LABEL index="5" value="50" />
      <LABEL index="6" value="60" />
      <LABEL index="7" value="70" />
      <LABEL index="8" value="80" />
      <LABEL index="9" value="90" />
      <LABEL index="10" value="100" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x387AC" mmedelementsizebits="16" mmedrowcount="11" mmedcolcount="7" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>kPa</units>
      <decimalpl>3</decimalpl>
      <min>0.000000</min>
      <max>255.996094</max>
      <MATH equation="X/256"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7E7" flags="0x30">
    <title>MAP Plausibility - Limit Factor vs Barometric Pressure</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the H3 check, not confirmed on a vehicle. MAP plausibility check: each sample in which manifold pressure is above the high limit or below the low limit for the current engine speed and throttle area counts as out of band; on this operating system both limits are first multiplied by the Limit Factor vs Barometric Pressure. This curve is that factor (1.0 = limits as in the tables) by barometric pressure. The H3 runs the same check with its enable switched off; whether it runs on this operating system has not been determined. Evidence: ledger:E1853</description>
    <CATEGORYMEM index="0" category="6" />
    <XDFAXIS id="x">
      <indexcount>9</indexcount>
      <units>kPa (barometric pressure)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="65" />
      <LABEL index="1" value="70" />
      <LABEL index="2" value="75" />
      <LABEL index="3" value="80" />
      <LABEL index="4" value="85" />
      <LABEL index="5" value="90" />
      <LABEL index="6" value="95" />
      <LABEL index="7" value="100" />
      <LABEL index="8" value="105" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x38848" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="9" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>factor</units>
      <decimalpl>4</decimalpl>
      <min>0.000000</min>
      <max>1.999969</max>
      <MATH equation="X/32768"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x7E8" flags="0x0">
    <title>MAP Plausibility - Fail Count</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the H3 check, not confirmed on a vehicle. MAP plausibility check (see the High / Low Limit tables): this is the number of out-of-band samples (manifold pressure outside the high / low limits) that ends a window as a failure. The branch flips exactly at this value (executed edge test against the check&#x27;s own sample counter). The H3 runs the same check with its enable switched off; whether it runs on this operating system has not been determined. Evidence: ledger:E1859</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x386F0" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7E9" flags="0x0">
    <title>MAP Plausibility - Window Samples</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator against the H3 check, not confirmed on a vehicle. MAP plausibility check (see the High / Low Limit tables): this is the number of samples in a window; when the window reaches it first, the window ends as a pass. The branch flips exactly at this value (executed edge test against the check&#x27;s own sample counter). The H3 runs the same check with its enable switched off; whether it runs on this operating system has not been determined. Evidence: ledger:E1859</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x386F2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>samples</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>65535.000000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFTABLE uniqueid="0x7EA" flags="0x30">
    <title>Spark Advance - Spark Mode 7 vs RPM vs Airmass</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator, not confirmed on a vehicle. Spark advance for every cylinder while the spark mode sequencer is in mode 7, by cylinder airmass (rows, 0.08 to 0.40 g/cyl) and engine speed (columns). Used when the spark mode selector is in mode 7. This OS can enter mode 7; whether it does in normal driving has not been determined. Effect: raise = more spark advance in spark mode 7 Evidence: ledger:E1617</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>9</indexcount>
      <units>g/cyl (cylinder airmass)</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0.08" />
      <LABEL index="1" value="0.12" />
      <LABEL index="2" value="0.16" />
      <LABEL index="3" value="0.2" />
      <LABEL index="4" value="0.24" />
      <LABEL index="5" value="0.28" />
      <LABEL index="6" value="0.32" />
      <LABEL index="7" value="0.36" />
      <LABEL index="8" value="0.4" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F2CD" mmedelementsizebits="8" mmedrowcount="9" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x01" />
      <units>deg</units>
      <decimalpl>1</decimalpl>
      <min>-64.000000</min>
      <max>63.500000</max>
      <MATH equation="X/2"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFTABLE uniqueid="0x7EB" flags="0x30">
    <title>Spark Mode Ramp - Into Spark Mode 7 vs RPM</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator, not confirmed on a vehicle. Spark reference ramp: when the spark mode sequencer enters mode 7 the spark reference blends from the old mode&#x27;s spark to the mode 7 spark over this many update cycles, by engine speed. The entry into mode 7 looks this curve up with the same engine speed input as the Into Decel Fuel Cut ramp. Used when the spark mode selector is in mode 7. This OS can enter mode 7; whether it does in normal driving has not been determined. Effect: raise = slower blend into spark mode 7 Evidence: ledger:E1876</description>
    <CATEGORYMEM index="0" category="1" />
    <XDFAXIS id="x">
      <indexcount>33</indexcount>
      <units>rpm</units>
      <embedinfo type="0" />
      <datatype>0</datatype><unittype>0</unittype><DALINK index="0" />
      <LABEL index="0" value="0" />
      <LABEL index="1" value="256" />
      <LABEL index="2" value="512" />
      <LABEL index="3" value="768" />
      <LABEL index="4" value="1024" />
      <LABEL index="5" value="1280" />
      <LABEL index="6" value="1536" />
      <LABEL index="7" value="1792" />
      <LABEL index="8" value="2048" />
      <LABEL index="9" value="2304" />
      <LABEL index="10" value="2560" />
      <LABEL index="11" value="2816" />
      <LABEL index="12" value="3072" />
      <LABEL index="13" value="3328" />
      <LABEL index="14" value="3584" />
      <LABEL index="15" value="3840" />
      <LABEL index="16" value="4096" />
      <LABEL index="17" value="4352" />
      <LABEL index="18" value="4608" />
      <LABEL index="19" value="4864" />
      <LABEL index="20" value="5120" />
      <LABEL index="21" value="5376" />
      <LABEL index="22" value="5632" />
      <LABEL index="23" value="5888" />
      <LABEL index="24" value="6144" />
      <LABEL index="25" value="6400" />
      <LABEL index="26" value="6656" />
      <LABEL index="27" value="6912" />
      <LABEL index="28" value="7168" />
      <LABEL index="29" value="7424" />
      <LABEL index="30" value="7680" />
      <LABEL index="31" value="7936" />
      <LABEL index="32" value="8192" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="y">
      <indexcount>1</indexcount>
      <units>index</units>
      <embedinfo type="0" />
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
    <XDFAXIS id="z">
      <EMBEDDEDDATA mmedaddress="0x2F02C" mmedelementsizebits="16" mmedrowcount="1" mmedcolcount="33" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
      <units>update cycles</units>
      <decimalpl>0</decimalpl>
      <min>0.000000</min>
      <max>65535.000000</max>
      <MATH equation="X"><VAR id="X" /></MATH>
    </XDFAXIS>
  </XDFTABLE>
  <XDFCONSTANT uniqueid="0x7EC" flags="0x0">
    <title>LTFT Floor During Enrichment - Catalyst Model Temperature Threshold</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator, not confirmed on a vehicle. A threshold: the code compares it with RAM word 0xFFFF0096 (catalyst model) and the branch flips exactly at the calibration value (executed edge test, same raw scale); its unit is the unit of that word. Evidence: ledger:E1886</description>
    <CATEGORYMEM index="0" category="2" />
    <EMBEDDEDDATA mmedaddress="0x218A2" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>degC</units>
    <decimalpl>2</decimalpl>
    <min>0.000000</min>
    <max>4095.937500</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/16"><VAR id="X" /></MATH>
  </XDFCONSTANT>
  <XDFCONSTANT uniqueid="0x7ED" flags="0x0">
    <title>Diagnostic RPM Ceiling - Engine RPM Threshold</title>
    <description>Change in small steps and log. OS 12610624 only: located from this operating system&#x27;s own code and checked in the emulator, not confirmed on a vehicle. A threshold: the code compares it with RAM word 0xFFFF1FAE (engine rpm) and the branch flips exactly at the calibration value (executed edge test, same raw scale); its unit is the unit of that word. Evidence: ledger:E1886</description>
    <CATEGORYMEM index="0" category="6" />
    <EMBEDDEDDATA mmedaddress="0x22C5A" mmedelementsizebits="16" mmedmajorstridebits="0" mmedminorstridebits="0" mmedtypeflags="0x00" />
    <units>rpm</units>
    <decimalpl>0</decimalpl>
    <min>0.000000</min>
    <max>8191.875000</max>
    <datatype>0</datatype>
    <unittype>0</unittype>
    <DALINK index="0" />
    <MATH equation="X/8"><VAR id="X" /></MATH>
  </XDFCONSTANT>
</XDFFORMAT>